Glo-Ray®
Designer Merchandising Warmers
Présentoirs Chauffants Designer
GR2SD Series/Série
Installation and Operating Manual
Manuel d’installation et d’utilisation
P/N 07.04.273.00 © 2020 Hatco Corporation
hatcocorp.com
Register Online!
(see page 2)
S’inscrire en ligne!
(voir page 19)
Do not operate this equipment unless you
have read and understood the contents
of this manual! Failure to follow the
instructions contained in this manual
may result in serious injury or death.
This manual contains important safety
information concerning the maintenance,
use, and operation of this product. If
you’re unable to understand the contents
of this manual, please bring it to the
attention of your supervisor. Keep this
manual in a safe location for future
reference.
English = p 2
WARNING
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en
este manual puede resultar en un serio
lesión o muerte. Este manual contiene
importante información sobre seguridad
concerniente al mantenimiento, uso y
operación de este producto. Si usted
no puede entender el contenido de
este manual por favor pregunte a su
supervisor. Almacenar este manual en
una localización segura para la referencia
futura.
ADVERTENCIA
Ne pas utiliser cet équipement sans avoir
lu et compris le contenu de ce manuel ! Le
non-respect des instructions contenues
dans ce manuel peut entraîner de
graves blessures ou la mort. Ce manuel
contient des informations importantes
concernant l’entretien, l’utilisation et le
fonctionnement de ce produit. Si vous ne
comprenez pas le contenu de ce manuel,
veuillez le signaler à votre supérieur.
Conservez ce manuel dans un endroit
sûr pour pouvoir vous y référer plus tard.
Français = p 19
AVERTISSEMENT
Form No. GR2SDM-0920
2
English
This manual provides installation, safety, and operating
instructions for Glo-Ray Designer Merchandising Warmers.
Hatco recommends all installation, operating, and safety
instructions appearing in this manual be read prior to installation
or operation of a unit.
Safety information that appears in this manual is identified by
the following signal word panels:
WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to
personal injury.
INTRODUCTION
Hatco Glo-Ray® Designer Merchandising Warmers, GR2SDH
(Horizontal Shelf) and GR2SDS (Slant Shelf), are perfect for
holding wrapped sandwiches or boxed pizza on a buffet line
or at temporary serving areas. These warmers safely hold
hot wrapped products and keep them at optimum serving
temperatures without affecting quality. Prefocused infrared
heat from above and a thermostatically-controlled heated base
extends the holding times of most wrapped food.
Glo-Ray Designer Merchandising Warmers are built with
quality to meet the demands of foodservice operations and
provide years of trouble-free performance. The metal-sheathed
tubular heating elements are guaranteed against breakage and
burnout for two years.
Glo-Ray Designer Merchandising Warmers are products of
extensive research and field testing. The materials used were
selected for maximum durability, attractive appearance and
optimum performance. Every unit is inspected and tested
thoroughly prior to shipment.
Important Owner Information ..............................................2
Introduction ...........................................................................2
Important Safety Information ..............................................3
Model Description ................................................................4
All Models ............................................................................ 4
GR2SDH Models ................................................................. 4
GR2SDS Models .................................................................4
Model Designation ...............................................................4
Specifications .......................................................................5
Plug Configurations .............................................................5
Electrical Rating Chart .........................................................5
Dimensions .......................................................................... 7
Installation ...........................................................................12
General .............................................................................. 12
Operation .............................................................................13
General .............................................................................. 13
Control Panel .....................................................................13
Operating the Unit .............................................................13
Maintenance ........................................................................14
General .............................................................................. 14
Daily Cleaning ...................................................................14
Replacing a Display Light ..................................................14
Troubleshooting Guide ......................................................15
Options and Accessories ..................................................15
Limited Warranty ................................................................18
IMPORTANT OWNER INFORMATION
Record the model number, serial number (specification label
located on the bottom of the unit), voltage, and purchase date
of the unit in the spaces below. Please have this information
available when calling Hatco for service assistance.
Model No. _______________________________________
Serial No. ________________________________________
Voltage __________________________________________
Date of Purchase __________________________________
Register your unit!
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the Hatco website at
www.hatcocorp.com, select the Support pull-down menu,
and click on “Warranty”.
Business
Hours: 7:00 to 5:00 Monday–Friday,
Central Time (CT)
(Summer Hours: June to September—
7:00 to 5:00 Monday–Thursday
7:00 to 4:00 Friday)
Telephone: 800-558-0607; 414-671-6350
E-mail: [email protected]
24 Hour 7 Day Parts and Service
Assistance available in the United States
and Canada by calling 800-558-0607.
Additional information can be found by visiting our web site at
www.hatcocorp.com.
CONTENTS
Form No. GR2SDM-0920 3
English IMPORTANT SAFETY INFORMATION
WARNING
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
Make sure all operators have been instructed on the safe
and proper use of the unit.
Make sure food product has been heated to the proper
food-safe temperature before placing in unit. Failure to
heat food product properly may result in serious health
risks. This unit is for holding pre-heated food product only.
CAUTION
BURN HAZARD: Some exterior surfaces on the unit will get
hot. Use caution when touching these areas.
Locate unit at proper counter height in an area that is
convenient for use. The location should be level to prevent
unit or its contents from falling accidentally and strong
enough to support the weight of unit and contents.
The National Sanitation Foundation (NSF) requires that
units over 36″ (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point
of use, 4″ (102 mm) legs are included to allow for proper
cleaning access below unit.
NOTICE
Only light bulbs which meet or exceed NSF standards,
specifically designed for food holding areas must be used.
Breakage of light bulbs not specially coated could result in
personal injury and/or food contamination.
Do not lay unit on the side with the control panel. Damage
to unit could occur.
IMPORTANT—DO NOT use paper towel or glass cleaner
to clean plastic surfaces such as sneeze guards and
flip-up doors. Paper towel and glass cleaner may scratch
the material. Wipe off plastic surfaces using a soft, clean,
water-dampened cloth.
Do not slide pans across hardcoat surface, use rough-
bottomed pans, or drop anything on hardcoat surface.
Scratching may occur. Damage to hardcoat surface caused
by misuse is not covered under warranty.
Transport unit in upright position only. Before moving or
tipping unit, secure all glass surfaces with tape. Failure to
do so may result in damage to unit or personal injury.
Do not locate unit in area with excessive air movement
around unit. Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods, air
conditioning ducts, and exterior doors).
Use non-abrasive cleaners only. Abrasive cleaners could
scratch the finish of the unit, marring its appearance and
making it susceptible to soil accumulation.
WARNING
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install the proper voltage
and size electrical receptacle.
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any maintenance or
cleaning.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 21°C (70°F).
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use
jet-clean spray to clean this unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not clean unit when it is energized or hot.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts may subject operators of the
equipment to hazardous electrical voltage, resulting in
electrical shock or burn. Genuine Hatco Replacement
Parts are specified to operate safely in the environments
in which they are used. Some aftermarket or generic
replacement parts do not have the characteristics that
will allow them to operate safely in Hatco equipment.
FIRE HAZARD: Locate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
EXPLOSION HAZARD: Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or
any other appliance.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
Form No. GR2SDM-0920
4
English
MODEL DESIGNATION
MODEL DESCRIPTION
All Models
All Glo-Ray® GR2SD models are constructed of aluminum
and stainless steel and feature tempered glass side panels, a
thermostatically-controlled heated base, infrared upper heating
elements, incandescent lights, product divider rods, legs,
Designer color inset panels, and a cord and plug set.
GR2SDH Models
The GR2SDH models are horizontal shelf warmers designed to
hold wrapped or boxed product.
The single and dual shelf models are available in widths
Glass Side
Panel
Product Divider Rod
GR2SDH-xx Model
GR2SDS Models
The GR2SDS models are slant shelf warmers designed to hold
wrapped or boxed product. The shelves are slanted for the
convenience of self-serve.
The single or dual shelf models are available in widths ranging
Glass Side
Panel
Product Divider Rod
GR2SDS-xxD Model
NOTE: GR2SDH and GR2SDS models cannot be converted
to each other.
G R 2 S D H - xx D
Glo-Ray
Designer
Sandwich Display
No Character = Single Shelf
D = Dual Shelf
T = Triple Shelf
Heated Surface Width (inches)
H = Horizontal Shelf
S = Slant Shelf
Form No. GR2SDM-0920 5
English
Model Voltage Watts Amps Plug Configuration Shipping Weight
GR2SDH-36T 120/208-240 3015 12.8 NEMA L14-20P 387 lbs. (176 kg)
GR2SDH-48T 120/208-240 4020 17.2 NEMA L14-20P 485 lbs. (220 kg)
Model Voltage Watts Amps Plug Configuration Shipping Weight
GR2SDH-24D 120 1640 13.7 NEMA 5-15P, NEMA 5-20P 126 lbs. (57 kg)
GR2SDH-30D 120/208-240 2040 8.5 NEMA L14-20P 158 lbs. (72 kg)
GR2SDH-36D 120/208-240 2440 10.2 NEMA L14-20P 205 lbs. (93 kg)
GR2SDH-42D 120/208-240 2980 12.4 NEMA L14-20P 225 lbs. (102 kg)
GR2SDH-48D 120/208-240 3380 14.1 NEMA L14-20P 254 lbs. (115 kg)
GR2SDH-54D 120/208-240 3780 15.8 NEMA L14-20P 274 lbs. (124 kg)
GR2SDH-60D 120/208-240 4420 18.4 NEMA L14-30P 328 lbs. (149 kg)
Model Voltage Watts Amps Plug Configuration Shipping Weight
GR2SDH-24 120 820 6.8 NEMA 5-15P, NEMA 5-20P 87 lbs. (40 kg)
GR2SDH-30 120 1020 8.5 NEMA 5-20P 120 lbs. (55 kg)
GR2SDH-36 120 1220 10.2 NEMA 5-20P 129 lbs. (59 kg)
GR2SDH-42 120 1490 12.4 NEMA 5-20P 138 lbs. (63 kg)
GR2SDH-48 120 1690 14.1 NEMA 5-20P 160 lbs. (73 kg)
GR2SDH-54 120 1890 15.8 NEMA 5-20P 172 lbs. (78 kg)
GR2SDH-60 120 2210 18.4 NEMA 5-30P 200 lbs. (91 kg)
SPECIFICATIONS
Plug Configurations
Units are supplied from the factory with an electrical cord and
plug installed. Plugs are supplied according to the applications.
WARNING
ELECTRIC SHOCK HAZARD: Plug unit into a properly
grounded electrical receptacle of the correct voltage,
size, and plug configuration. If plug and receptacle do not
match, contact a qualified electrician to determine and
install the proper voltage and size electrical receptacle.
NOTE: The specification label is located on the bottom of the
unit. See label for serial number and verification of unit
electrical information.
NOTE: Receptacle not supplied by Hatco.
NEMA 5-15P NEMA 5-20P NEMA 5-30P
NEMA L14-20P NEMA L14-30P
NEMA 14-20P NEMA 14-30P
Plug Configurations
Electrical Rating Chart — GR2SDH-xx Models
Electrical Rating Chart — GR2SDH-xxD Models
Electrical Rating Chart — GR2SDH-xxT Models
Form No. GR2SDM-0920
6
English
Model Voltage Watts Amps Plug Configuration Shipping Weight
GR2SDS-24 120 820 6.8 NEMA 5-15P 102 lbs. (46 kg)
GR2SDS-30 120 1020 8.5 NEMA 5-15P 110 lbs. (50 kg)
GR2SDS-36 120 1220 10.2 NEMA 5-15P 136 lbs. (62 kg)
GR2SDS-42 120 1490 12.4 NEMA 5-15P, NEMA 5-20P 155 lbs. (70 kg)
GR2SDS-48 120 1690 14.1 NEMA 5-15P, NEMA 5-20P 164 lbs. (74 kg)
GR2SDS-54 120 1890 15.8 NEMA 5-20P 182 lbs. (83 kg)
GR2SDS-60 120 2210 18.4 NEMA 5-30P 202 lbs. (92 kg)
Model Voltage Watts Amps Plug Configuration Shipping Weight
GR2SDS-24D 120 1640 13.7 NEMA 5-15P, NEMA 5-20P 160 lbs. (73 kg)
GR2SDS-30D 120/208-240 2040 8.5 NEMA L14-20P 184 lbs. (83 kg)
GR2SDS-36D 120/208-240 2440 10.2 NEMA L14-20P 200 lbs. (91 kg)
GR2SDS-42D 120/208-240 2980 12.4 NEMA L14-20P 218 lbs. (99 kg)
GR2SDS-48D 120/208-240 3380 14.1 NEMA L14-20P 255 lbs. (116 kg)
GR2SDS-54D 120/208-240 3780 15.8 NEMA L14-20P 265 lbs. (120 kg)
GR2SDS-60D 120/208-240 4420 18.4 NEMA L14-30P 296 lbs. (135 kg)
SPECIFICATIONS
Electrical Rating Chart — GR2SDS-xx Models
Electrical Rating Chart — GR2SDS-xxD Models
Form No. GR2SDM-0920 7
English
Model Width
(A) Depth
(B)‡ Height
(C)
Heated
Shelf Width
(D)
Heated
Shelf Depth
(E)
Footprint
Width
(F)
Footprint
Depth
(G)
GR2SDH-24 30-1/4
(768 mm)
27
(686 mm)
18-1/8
(460 mm)
23-7/8
(606 mm)
23-7/8
(606 mm)
22-5/8
(575 mm)
20-1/2
(521 mm)
GR2SDH-30 36-1/4
(921 mm)
27
(686 mm)
18-1/8
(460 mm)
29-7/8
(759 mm)
23-7/8
(606 mm)
28-5/8
(727 mm)
20-1/2
(521 mm)
GR2SDH-36 42-1/4
(1073 mm)
27
(686 mm)
18-1/8
(460 mm)
35-7/8
(911 mm)
23-7/8
(606 mm)
34-5/8
(879 mm)
20-1/2
(521 mm)
GR2SDH-42 48-1/4
(1226 mm)
27
(686 mm)
18-1/8
(460 mm)
41-7/8
(1064 mm)
23-7/8
(606 mm)
40-5/8
(1032 mm)
20-1/2
(521 mm)
GR2SDH-48 54-1/4
(1378 mm)
27
(686 mm)
18-1/8
(460 mm)
47-7/8
(1216 mm)
23-7/8
(606 mm)
46-5/8
(1184 mm)
20-1/2
(521 mm)
GR2SDH-54 60-1/4
(1530 mm)
27
(686 mm)
18-1/8
(460 mm)
53-7/8
(1368 mm)
23-7/8
(606 mm)
52-5/8
(1337 mm)
20-1/2
(521 mm)
GR2SDH-60 66-1/4
(1683 mm)
27
(686 mm)
18-1/8
(460 mm)
59-7/8
(1521 mm)
23-7/8
(606 mm)
58-5/8
(1489 mm)
20-1/2
(521 mm)
SPECIFICATIONS
Dimensions — GR2SDH-xx Models
‡
(48 mm) to Depth (B).
A
C
F
B
G
Front View Side View
D
E
1-7/8″
(48 mm)
8″
(204 mm)
GR2SDH-xx Dimensions
Form No. GR2SDM-0920
8
English
Model Width
(A) Depth
(B)‡ Height
(C)
Heated
Shelf Width
(D)
Heated
Shelf Depth
(E)
Footprint
Width
(F)
Footprint
Depth
(G)
GR2SDH-24D 30-1/4
(768 mm)
27
(686 mm)
29
(737 mm)
23-7/8
(606 mm)
23-7/8
(606 mm)
22-5/8
(575 mm)
20-1/2
(521 mm)
GR2SDH-30D 36-1/4
(921 mm)
27
(686 mm)
29
(737 mm)
29-7/8
(759 mm)
23-7/8
(606 mm)
28-5/8
(727 mm)
20-1/2
(521 mm)
GR2SDH-36D 42-1/4
(1073 mm)
27
(686 mm)
29
(737 mm)
35-7/8
(911 mm)
23-7/8
(606 mm)
34-5/8
(879 mm)
20-1/2
(521 mm)
GR2SDH-42D 48-1/4
(1226 mm)
27
(686 mm)
29
(737 mm)
41-7/8
(1064 mm)
23-7/8
(606 mm)
40-5/8
(1032 mm)
20-1/2
(521 mm)
GR2SDH-48D 54-1/4
(1378 mm)
27
(686 mm)
29
(737 mm)
47-7/8
(1216 mm)
23-7/8
(606 mm)
46-5/8
(1184 mm)
20-1/2
(521 mm)
GR2SDH-54D 60-1/4
(1530 mm)
27
(686 mm)
29
(737 mm)
53-7/8
(1368 mm)
23-7/8
(606 mm)
52-5/8
(1337 mm)
20-1/2
(521 mm)
GR2SDH-60D 66-1/4
(1683 mm)
27
(686 mm)
29
(737 mm)
59-7/8
(1521 mm)
23-7/8
(606 mm)
58-5/8
(1489 mm)
20-1/2
(521 mm)
SPECIFICATIONS
Dimensions — GR2SDH-xxD Models
A
C
FG
Front View
D
B
E
8″
(204 mm)
8″
(204 mm)
1-7/8″
(48 mm)
GR2SDH-xxD Dimensions
‡ Depth (B) dimension is for units with a thermostatic control. For units with an optional digital temperature controller add 48 mm
Form No. GR2SDM-0920 9
English
Model Width
(A) Depth
(B)‡ Height
(C)
Heated
Shelf Width
(D)
Heated
Shelf Depth
(E)
Footprint
Width
(F)
Footprint
Depth
(G)
GR2SDH-36T 42-1/4
(1080 mm)
27
(686 mm)
40-3/16
(1020 mm)
35-7/8
(911 mm)
24
(610 mm)
34-5/8
(878 mm)
20-1/2
(521 mm)
GR2SDH-48T 54-1/4
(1378 mm)
27
(686 mm)
40-3/16
(1020 mm)
47-7/8
(1216 mm)
24
(610 mm)
46-5/8
(1183 mm)
20-1/2
(521 mm)
SPECIFICATIONS
Dimensions — GR2SDH-xxT Models
A
C
FG
D
Front View Side View
B
E
8″
(204 mm)
8″
(204 mm)
8″
(204 mm)
GR2SDH-xxT Dimensions
‡
(48 mm) to Depth (B).
Form No. GR2SDM-0920
10
English
Model Width
(A) Depth
(B)‡ Height
(C)
Heated
Shelf Width
(D)
Heated
Shelf Depth
(E)
Footprint
Width
(F)
Footprint
Depth
(G)
GR2SDS-24 30-1/4
(768 mm)
26-5/8
(676 mm)
22-7/8
(581 mm)
23-7/8
(606 mm)
23-7/8
(606 mm)
22-5/8
(575 mm)
20-1/2
(521 mm)
GR2SDS-30 36-1/4
(921 mm)
26-5/8
(676 mm)
22-7/8
(581 mm)
29-7/8
(759 mm)
23-7/8
(606 mm)
28-5/8
(727 mm)
20-1/2
(521 mm)
GR2SDS-36 42-1/4
(1073 mm)
26-5/8
(676 mm)
22-7/8
(581 mm)
35-7/8
(911 mm)
23-7/8
(606 mm)
34-5/8
(879 mm)
20-1/2
(521 mm)
GR2SDS-42 48-1/4
(1226 mm)
26-5/8
(676 mm)
22-7/8
(581 mm)
41-7/8
(1064 mm)
23-7/8
(606 mm)
40-5/8
(1032 mm)
20-1/2
(521 mm)
GR2SDS-48 54-1/4
(1378 mm)
26-5/8
(676 mm)
22-7/8
(581 mm)
47-7/8
(1216 mm)
23-7/8
(606 mm)
46-5/8
(1184 mm)
20-1/2
(521 mm)
GR2SDS-54 60-1/4
(1530 mm)
26-5/8
(676 mm)
22-7/8
(581 mm)
53-7/8
(1368 mm)
23-7/8
(606 mm)
52-5/8
(1337 mm)
20-1/2
(521 mm)
GR2SDS-60 66-1/4
(1683 mm)
26-5/8
(676 mm)
22-7/8
(581 mm)
59-7/8
(1521 mm)
23-7/8
(606 mm)
58-5/8
(1489 mm)
20-1/2
(521 mm)
SPECIFICATIONS
Dimensions — GR2SDS-xx Models
A
C
F
B
G
D
Front View Side View
E
18-5/8″
(472 mm)
7-7/8″
(201 mm)
1-7/8″
(48 mm)
GR2SDS-xx Dimensions
‡
(48 mm) to Depth (B).
Form No. GR2SDM-0920 11
English
Model Width
(A) Depth
(B)‡ Height
(C)
Heated
Shelf Width
(D)
Heated
Shelf Depth
(E)
Footprint
Width
(F)
Footprint
Depth
(G)
GR2SDS-24D 30-1/4
(768 mm)
26-5/8
(676 mm)
33-7/8
(860 mm)
23-7/8
(606 mm)
23-7/8
(606 mm)
22-5/8
(575 mm)
20-1/2
(521 mm)
GR2SDS-30D 36-1/4
(921 mm)
26-5/8
(676 mm)
33-7/8
(860 mm)
29-7/8
(759 mm)
23-7/8
(606 mm)
28-5/8
(727 mm)
20-1/2
(521 mm)
GR2SDS-36D 42-1/4
(1073 mm)
26-5/8
(676 mm)
33-7/8
(860 mm)
35-7/8
(911 mm)
23-7/8
(606 mm)
34-5/8
(879 mm)
20-1/2
(521 mm)
GR2SDS-42D 48-1/4
(1226 mm)
26-5/8
(676 mm)
33-7/8
(860 mm)
41-7/8
(1064 mm)
23-7/8
(606 mm)
40-5/8
(1032 mm)
20-1/2
(521 mm)
GR2SDS-48D 54-1/4
(1378 mm)
26-5/8
(676 mm)
33-7/8
(860 mm)
47-7/8
(1216 mm)
23-7/8
(606 mm)
46-5/8
(1184 mm)
20-1/2
(521 mm)
GR2SDS-54D 60-1/4
(1530 mm)
26-5/8
(676 mm)
33-7/8
(860 mm)
53-7/8
(1368 mm)
23-7/8
(606 mm)
52-5/8
(1337 mm)
20-1/2
(521 mm)
GR2SDS-60D 66-1/4
(1683 mm)
26-5/8
(676 mm)
33-7/8
(860 mm)
59-7/8
(1521 mm)
23-7/8
(606 mm)
58-5/8
(1489 mm)
20-1/2
(521 mm)
SPECIFICATIONS
Dimensions — GR2SDS-xxD Models
A
C
FG
D
Front View Side View
B
E
29-5/8″
(752 mm)
7-7/8″
(201 mm)
7-7/8″
(201 mm)
1-7/8″
(48 mm)
GR2SDS-xxD Dimensions
‡
(48 mm) to Depth (B).
Form No. GR2SDM-0920
12
English
INSTALLATION
5. Install the channel dividers and product divider bars.
a. Position the channel dividers onto the locator pins on
the front edge and back edge of the unit.
b. Place the product divider bars into the channel dividers.
The bars can be adjusted easily to separate holding
areas as needed.
Locator Pin
Channel Divider
Product Divider Rod
Installing Product Divider Bars
6. Install the glass side panels on each side of the unit. To
install the side panels:
a. Angle the top edge into the upper channel.
b. Carefully lower the bottom edge into the lower channel.
Do not allow the panel to drop into position.
Glass Side Panel
Upper Channel
Lower Channel
Side Glass Panel Installation
7. Place the unit in the desired location. Two people are
required for this step.
• Locate the unit in an area where the ambient air
temperature is constant and a minimum of 70°F
(21°C). Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods,
air conditioning ducts, and exterior doors).
• Make sure the unit is at the proper counter height in an
area convenient for use.
• Make sure the countertop is level and strong enough to
support the weight of the unit and food product.
8. For units without plugs, have a qualified electrician install
proper plug or hardwire to on-site power source.
General
Glo-Ray® Designer Merchandising Warmers are shipped
with most components pre-assembled. Care should be taken
when unpacking shipping carton to avoid damage to unit and
components enclosed.
WARNING
ELECTRIC SHOCK HAZARD: Unit is not weatherproof.
Locate the unit indoors where the ambient air temperature
is a minimum of 21°C (70°F).
FIRE HAZARD: Do not install unit above or around
combustible surfaces. Discoloration or combustion
could occur. Unit must be installed in non-combustible
surroundings only.
CAUTION
Locate unit at the proper counter height in an area that is
convenient for use. The location should be level to prevent
the unit or its contents from falling accidentally and strong
enough to support the weight of the unit and contents.
The National Sanitation Foundation (NSF) requires that
units over 36″ (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point
of use, 4″ (102 mm) legs are included to allow for proper
cleaning access below unit.
Transport unit in upright position only. Before moving or
tipping unit, secure all glass surfaces with tape. Failure to
do so may result in damage to unit or personal injury.
1. Remove the unit from the shipping carton and remove all
packing materials.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
2. Remove tape and protective packaging from all surfaces
of the unit.
3. Carefully lay the unit on its side and install the four
Designer legs. Two people are required for this step.
At each corner on the bottom of the unit:
a. Thread a hex bolt through the short rubber foot (bolt
head on recessed side of foot), through the Designer leg
and into the corner hole on the base. Tighten securely.
Designer Leg
Rubber Foot
Hex Bolt
4. After all the legs are secure, return the unit to its upright
position. Two people are required for this step.
Form No. GR2SDM-0920 13
English
General
Use the following procedures to operate the Glo-Ray Designer
Merchandising Warmers.
WARNING
Read all safety messages in the IMPORTANT SAFETY
INFORMATION section before operating this equipment.
CAUTION
BURN HAZARD: Some exterior surfaces on the unit will
get hot. Avoid unnecessary contact with unit.
NOTICE
Do not place food product directly onto hardcoat surface.
Food product must be wrapped, boxed, or on a food pan.
Control Panel
The following descriptions of the controls used to operate the
unit. all controls are located on the control panel at the back
of the unit.
NOTE: The “1” on the control panel indicates controls for the
base. The “2” indicates controls for the shelf.
Base Temperature Control
The Base Temperature Control knob controls heat to the
base of the unit. Turning the Base Temperature Control knob
clockwise will increase the temperature setting. Turning the
Base Temperature Control knob counterclockwise will decrease
the temperature setting.
Shelf Temperature Control
The Shelf Temperature Control knob controls heat to the center
shelf of dual and triple shelf units. Turning the Shelf Temperature
Control knob clockwise will increase the temperature setting.
Turning the Shelf Temperature Control knob counterclockwise
will decrease the temperature setting.
Base Power I/O (on/off) Toggle Switch
The Base Power I/O (on/off) Toggle Switch controls power to
the base.
Shelf Power I/O (on/off) Toggle Switch
The Shelf Power I/O (on/off) Toggle Switch controls power to
the center shelf.
Operating the Unit
Startup
1. Plug unit into a properly grounded electrical receptacle of
the correct voltage, size and plug configuration. See the
SPECIFICATIONS section for details.
2. Move the Power I/O (on/off) toggle switch(es) to the I (on)
position.
• The overhead strip heaters and overhead lights will turn
on.
• The heated base(s) will energize.
3. Turn the Temperature Control(s) to the desired temperature
setting for the heated base(s). The operating temperature
range of the heated base(s) is from room temperature to
approximately 185°–200°F (85°–93°C).
• Turning the Temperature Control clockwise will increase
the temperature setting. Turning the Temperature
Control counterclockwise will decrease the temperature
setting.
NOTE: For units equipped with a digital temperature controller,
refer to the OPTIONS AND ACCESSORIES section of
this manual.
4. Allow the unit 30 minutes to reach operating temperature
before placing preheated food product.
Shutdown
1. Move the Power I/O (on/off) switch(es) to the O (off)
position. The overhead strip heaters, overhead lights, and
heated base(s) will shut off.
2. Perform the “Daily Cleaning” procedure in the
MAINTENANCE section of this manual.
OPERATION
HATCO CORPORATION MILWAUKEE, WI U.S.A.
www.hatcocorp.com
Base Power I/O (on/off)
Toggle Switch
Base
Indicator
Light
Base
Temperature
Control
Shelf
Indicator
Light
Shelf
Temperature
Control
Shelf Power I/O (on/off)
Toggle Switch
Control Panel (Dual Model Shown)
Form No. GR2SDM-0920
14
English
MAINTENANCE
General
Hatco Glo-Ray® Designer Merchandising Warmers are
designed for maximum durability and performance, with
minimum maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any maintenance or
cleaning.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
Daily Cleaning
To preserve the finish of the unit as well as maintain
performance, it is recommended that the unit be cleaned daily.
NOTICE
Submerging or saturating unit with water will damage unit
and void product warranty.
IMPORTANT—DO NOT use paper towel or glass cleaner
to clean plastic surfaces such as sneeze guards and
flip-up doors. Paper towel and glass cleaner may scratch
the material. Wipe off plastic surfaces using a soft, clean,
water-dampened cloth.
Use non-abrasive cleaners only. Abrasive cleaners could
scratch the finish of the unit, marring its appearance and
making it susceptible to soil accumulation.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Wipe down all exterior and interior surfaces using a damp
cloth. A non-abrasive cleaner may be used for difficult
stains. Hard to reach areas should be cleaned using small
brush and mild soap.
3. Clean the glass side panels using a standard glass cleaner.
4. Clean the plastic sneeze guards and flip-up doors (if
equipped) using soft cleaning cloths, mild soap, and water,
if equipped. NOTICE: Do not use paper towel or glass
cleaner on plastic sneeze guards — scratching may
occur.
Replacing A Display Light
WARNING
Use only light bulbs that meet or exceed National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of light bulbs
not specially coated could result in personal injury and/or
food contamination.
The display light is an incandescent bulb that illuminates the
warming area. This bulb has a special coating to guard against
injury and food contamination in the event of breakage.
To replace a light bulb:
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Unscrew the light bulb from the unit and replace it with a
new, specially-coated incandescent light bulb.
NOTE: Hatco shatter-resistant light bulbs meet NSF standards
for food holding and display areas. For 120, 120/208,
and 120/240 volt applications, use Hatco P/N
02.30.265.00.
NOTE: Halogen bulbs are available as an option. For 120,
120/208, and 120/240 volt applications, use Hatco P/N
02.30.081.00.
Form No. GR2SDM-0920 15
English
Symptom Probable Cause Corrective Action
Light bulb not working. Light bulb defective. Replace light bulb.
Power turned OFF. Move Power I/O (on/off) switch(es) to the On (I)
position.
Base food holding area not hot
enough.
Temperature control set too low. Adjust temperature control to a higher setting.
Base Power I/O (on/off) Toggle Switch in the O
(off) position.
Move Base Power I/O (on/off) Toggle Switch to the
I (on) position.
Heating element(s) not working. Contact an Authorized Hatco Service Agent or Hatco
for assistance.
Temperature control not working properly.
Excessive air movement around unit. Restrict or redirect air movement (i.e., air conditioning
duct or exhaust fan) away from unit or install flip-up
doors on unit to contain heat and block air flow.
Unit connected to incorrect power supply. Contact an Authorized Hatco Service Agent or Hatco
for assistance.
Base food holding area too hot. Temperature control set too high. Adjust Temperature control to a lower setting.
Temperature control not working properly. Contact an Authorized Hatco Service Agent or Hatco
for assistance.
Unit connected to incorrect power supply.
No heat, but light works. Temperature control set too low. Adjust Temperature control to a higher setting.
Heating element(s) not working. Contact an Authorized Hatco Service Agent or Hatco
for assistance.
Temperature control not working properly.
No heat and no light. Power turned OFF. Move Power I/O (on/off) switch(es) to the I (on)
position.
Circuit breaker tripped. Reset circuit breaker. If circuit breaker continues to
trip, contact Authorized Service Agent or Hatco for
assistance.
TROUBLESHOOTING GUIDE
WARNING
This unit must be serviced by trained and qualified
personnel only. Service by unqualified personnel may lead
to electric shock or burn.
WARNING
ELECTRIC SHOCK HAZARD: Turn power switch OFF,
unplug power cord, and allow unit to cool before
performing any maintenance or cleaning.
Troubleshooting Questions?
If you continue to have problems resolving an issue, please contact the nearest Authorized Hatco Service Agency or Hatco for
assistance. To locate the nearest Service Agency, log onto the Hatco website at www.hatcocorp.com, select the Support pull-
down menu, and click on “Find A Service Agent”; or contact the Hatco Parts and Service Team at:
Telephone: 800-558-0607 or 414-671-6350 e-mail: [email protected]
OPTIONS AND ACCESSORIES
Chef LED Bulbs
Chef LED bulbs are available for all lighted units. Chef LED
bulbs are LED light bulbs that offer energy savings over
incandescent bulbs. Use the following for replacement bulbs:
120 Volts
2700K: R02.30.185.01
3000K: R02.30.195.01
4000K: R02.30.196.01
230 Volts
2700K: R02.30.197.01
3000K: R02.30.198.01
4000K: R02.30.199.01
Form No. GR2SDM-0920
16
English
OPTIONS AND ACCESSORIES
Sneeze Guards
Sneeze guards are available for the unit. GR2SDH models can
be fitted with sneeze guards above each shelf on both sides
of the unit. GR2SDS models can be fitted with sneeze guards
above each shelf on the customer side of the unit only. Use the
following procedure to install sneeze guards.
NOTE: This option is factory-installed only, not available for retrofit.
1. Remove protective paper from all surfaces.
2. Slide the sneeze guard into the channel on the unit and
align the holes on the sneeze guard with the screw holes
in the channel.
3. Insert the thumbscrews from the top side of the channel,
through the sneeze guard, and out through the bottom of
the channel.
4. Place the cap nuts on the thumbscrews and tighten until
snug. Do not over-tighten the nuts.
Sneeze Guard
Cap Nut
Thumbscrew
Channel
Installing a Sneeze Guard
Flip-Up Doors
Flip-up doors are available for either the customer side or the
control side of the unit. Flip-up doors help keep heat in and air
currents away from the heat zone. They can only be installed
on one side of the unit and not on the same side with sneeze
guards. Use the following procedure to install flip-up doors (the
procedure is the same for either side as well as each shelf).
NOTE: Units 48 and larger require 2 doors per shelf and a
center mounting bracket.
1. Remove the two screws from the element end cover above
the desired shelf on each side of the unit.
2. Install the left mounting bracket and right mounting bracket
onto the appropriate side of the unit. To install each bracket:
a. Align the holes on the mounting bracket with the screw
holes on the element end cover of the unit.
b. Insert the previously removed screws through the
mounting bracket and into the unit. Tighten securely.
Digital Temperature Controller
Single and dual shelved units may be equipped with an optional
digital temperature controller that regulates and displays the
base temperature(s). Use the following procedures to operate
the digital temperature controller.
NOTE: This option is factory-installed only, not available for
retrofit.
NOTE: Units manufactured for use outside of Canada will have
digital temperature controllers that indicate temperature
in Celsius (°C).
“out 1” Fahrenheit
Symbol
Down Arrow
Key Up Arrow
Key
SET
Key
Digital Temperature Controller
1. Move the unit Power I/O (on/off) toggle switch(es) to the I
(on) position.
• The digital temperature controller will energize and the
current temperature of the heated base(s) will appear on
the display. CAUTION! Some exterior surfaces on the
unit will get hot. Use caution when touching these
areas.
• The phrase “out 1” will appear in the upper left corner of
the display to show that the base is in heat mode.
2. Press and release the key. The current setpoint
temperature will be shown on the display and ”out 1” will
flash in the upper left corner.
3. Press the key or key within 15 seconds to
change the setpoint temperature. If no key is pressed
within 15 seconds, the display will revert to the current
temperature of the heated base(s)
4. Press the key or wait 15 seconds to lock in the new
setpoint temperature. The setpoint temperature range of
the controller is from room temperature to 70°C (158°F).
Locking/Unlocking the Digital Temperature
Controller
The keys on the digital temperature controller can be locked to
prevent unauthorized changes to the settings.
To lock the keys of the digital temperature controller:
• Press and hold both the key and key at the
same time for over two seconds. The message “Loc” will
appear on the display.
To unlock the keys of the digital temperature controller:
• Press and hold both the key and key at the
same time until the message “UnL” appears on the display.
Form No. GR2SDM-0920 17
English
Stainless Steel Divider Rods
Additional stainless steel divider rods are available to help
keep product separate in the channels.
Designer Inset Color Panels
Choose from several Designer colors to coordinate the inset
panels on the merchandising warmer to surrounding decór.
NOTE: This option is factory-installed only, not available for
retrofit.
Display Sign Holder
Advertise specials or showcase product with easy-to-use signs.
To install sign holder, follow these steps.
1. Attach strap clip brackets to sign holder brackets with
screws and cap nuts.
• Two hole positions on the sign holder brackets provide
angle adjustment. Select the desired holes for placement
on either a slant or horizontal unit.
Screw
Cap
Nut
Right Strap
Clip Bracket
Left Strap
Clip Bracket
Sign Holder
Assembly
Adjustment
Holes
Attaching the Strap Clip Assemblies
2. Position the strap clip brackets on top of the warmer and
carefully snap them over the top of the bull nose trim piece
on the front and rear of the warmer.
3. Insert a thin sign panel behind the clear panel provided.
Bullnose
Trim Piece
Strap Clip
Brackets
Sign Holder
Assembly
Display Sign Holder
Left Mounting
Bracket
Center Mounting
Bracket
Right Mounting
Bracket
Flip-Up Door Mounting Brackets
NOTE:For units 48″ and larger, a center
mounting bracket is required. Remove
the screws from the center of the
middle or top housing and use them
to mount the center mounting bracket.
3. Remove one of the hinge screws from the
end of the hinge on the flip-up door assembly
4. Install the flip-up door onto the mounting brackets.
a. Pass the assembled hinge screw on the door through
the hole in either the left or right mounting bracket (use
b. Align the screw hole at the opposite end of the door
hinge with the hole in the mounting bracket.
c. Insert the hinge screw through the mounting bracket and
into the door hinge. Tighten the hinge screw until the
door is secure. Do not over-tighten.
NOTE: Apply thread locking compound to the removed hinge
screw before installation.
Left
Mounting
Bracket
End
Cover
Screw
End
Cover
Left Mounting
Bracket
End Cover
Screw
Hinge
Hinge Screw Flip-Up
Door
Flip-Up Door Installation
OPTIONS AND ACCESSORIES
Form No. GR2SDM-0920
18
English
1. PRODUCT WARRANTY
Hatco warrants the products that it manufactures (the “Products”)
to be free from defects in materials and workmanship, under
normal use and service, for a period of one (1) year from the
date of purchase when installed and maintained in accordance
with Hatco’s written instructions or 18 months from the date
of shipment from Hatco. Buyer must establish the Product’s
purchase date by registering the Product with Hatco or by other
means satisfactory to Hatco in its sole discretion.
Hatco warrants the following Product components to be free
from defects in materials and workmanship from the date of
purchase (subject to the foregoing conditions) for the period(s)
of time and on the conditions listed below:
a) One (1) Year Parts and Labor PLUS One (1) Additional
Year Parts-Only Warranty:
Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Strip Heater Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
Holding Cabinet Elements (metal sheathed air heating)
Heated Well Elements — HW and HWB Series
(metal sheathed)
b) Two (2) Year Parts and Labor Warranty:
Induction Ranges
Induction Warmers
c) One (1) Year Parts and Labor PLUS Four (4) Years
Parts-Only Warranty:
3CS and FR Tanks
d) One (1) Year Parts and Labor PLUS Nine (9) Years
Parts-Only Warranty on:
Electric Booster Heater Tanks
Gas Booster Heater Tanks
e) Ninety (90) Day Parts-Only Warranty:
Replacement Parts
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND
IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE OR PATENT OR OTHER
INTELLECTUAL PROPERTY RIGHT INFRINGEMENT. Without
limiting the generality of the foregoing, SUCH WARRANTIES
DO NOT COVER: Coated incandescent light bulbs, fluorescent
lights, heat lamp bulbs, coated halogen light bulbs, halogen
heat lamp bulbs, xenon light bulbs, LED light tubes, glass
components, and fuses; Product failure in booster tank, fin
tube heat exchanger, or other water heating equipment caused
by liming, sediment buildup, chemical attack, or freezing;
or Product misuse, tampering or misapplication, improper
installation, or application of improper voltage.
2. LIMITATION OF REMEDIES AND DAMAGES
Hatco’s liability and Buyer’s exclusive remedy hereunder will
be limited solely, at Hatco’s option, to repair or replacement
using new or refurbished parts or Product by Hatco or a Hatco-
authorized service agency (other than where Buyer is located
outside of the United States, Canada, United Kingdom, or
Australia, in which case Hatco’s liability and Buyer’s exclusive
remedy hereunder will be limited solely to replacement of part
under warranty) with respect to any claim made within the
applicable warranty period referred to above. Hatco reserves
the right to accept or reject any such claim in whole or in part. In
the context of this Limited Warranty, “refurbished” means a part
or Product that has been returned to its original specifications
by Hatco or a Hatco-authorized service agency. Hatco will not
accept the return of any Product without prior written approval
from Hatco, and all such approved returns shall be made
at Buyer’s sole expense. HATCO WILL NOT BE LIABLE,
UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED
TO LABOR COSTS OR LOST PROFITS RESULTING FROM
THE USE OF OR INABILITY TO USE THE PRODUCTS OR
FROM THE PRODUCTS BEING INCORPORATED IN OR
BECOMING A COMPONENT OF ANY OTHER PRODUCT OR
GOODS.
LIMITED WARRANTY
Formulaire n° GR2SDM-0920 19
Français
Ce manuel contient des instructions relatives à l’installation, à la
sécurité et au fonctionnement des présentoirs chauffants Hatco
Glo-Ray Designer. Hatco vous recommande de lire l’ensemble
des instructions d’installation, de sécurité et de fonctionnement
contenues dans ce manuel avant d’installer et d’utiliser appareil.
Les consignes de sécurité qui apparaissent dans ce manuel
sont identifiées par les mots indicateurs suivants :
AVERTISSEMENT
AVERTISSEMENT indique une situation dangereuse qui,
si elle n’est pas évitée, peut provoquer la mort ou des
blessures graves.
ATTENTION
ATTENTION indique une situation dangereuse qui, si elle
n’est pas évitée, peut provoquer des blessures légères ou
moyennes.
AVIS
AVIS est utilisé pour des questions sans rapport avec des
blessures corporelles.
INTRODUCTION
Les présentoirs chauffants Designer Hatco Glo-Ray®, GR2SDH
(rayonnage horizontal) et GR2SDS (rayonnage incliné) sont
parfaitement conçus pour présenter des sandwiches ou des
pizzas emballés sur un buffet ou dans un espace de service
temporaire. Ces appareils chauffants maintiendront vos
aliments emballés à des températures optimales ; ils seront
prêts à être servis à tout moment sans que la qualité ne soit
altérée. Le système chauffant à infrarouge focalisé, situé
au-dessus de la cuve, et une base chauffante à contrôle
thermostatique permet de conserver vos produits emballés au
chaud plus longtemps.
Les présentoirs chauffants Designer Glo-Ray répondent à des
normes de qualité conformes aux exigences du secteur de la
restauration et offrent des performances optimales pendant
des années. Les éléments métalliques chauffants tubulaires
sont garantis deux ans contre toute rupture et panne électrique.
Les présentoirs chauffants Designer Glo-Ray de Hatco sont
le résultat de longues recherches et de nombreux essais sur
le terrain. Les matériaux utilisés ont été sélectionnés pour
une durabilité maximum, une apparence séduisante et des
performances optimum. Chaque unité est inspectée et testée
minutieusement avant d’être expédiée.
Informations Importantes pour le Propriétaire ....................19
Introduction .........................................................................19
Consignes de Sécurité Importantes ................................. 20
Description du Modèle .......................................................21
Tous les Modèles ...............................................................21
Modèles GR2SDH ............................................................. 21
Modèles GR2SDS .............................................................21
Désignation du Modèle ...................................................... 21
Caractéristiques Techniques ............................................22
Configuration des Fiches ...................................................22
Tableau des Caractéristiques électriques..........................22
Dimensions ........................................................................ 24
Installation ...........................................................................28
Généralités ........................................................................28
Mode d’emploi ....................................................................29
Généralités ........................................................................29
Panneau de contrôle .........................................................29
Fonctionnement de l’appareil ............................................29
Maintenance ........................................................................30
Généralités ........................................................................30
Nettoyage quotidien ...........................................................30
Remplacement du tube d’éclairage ...................................30
Guide de Dépannage ..........................................................31
Options et Accessoires .....................................................32
Garantie Limitée .................................................................35
INFORMATIONS IMPORTANTES POUR LE PROPRIÉTAIRE
Notez le numéro de modèle, le numéro de série, la tension
et la date d’achat de l’appareil dans les espaces ci-dessous
(étiquette des caractéristiques techniques située sur le dessous
de l’appareil). Veuillez avoir cette information à portée de la
main si vous appelez Hatco pour assistance.
Modèle No. ______________________________________
Numéro de série __________________________________
Voltage _________________________________________
Date d’achat _____________________________________
Enregistrez votre appareil!
Remplissez la garantie en ligne pour éviter les retards
pour faire jouer la garantie. Accédez au site Web Hatco
www.hatcocorp.com, sélectionnez le menu déroulant
Support (Assistance), puis cliquez sur « Warranty » (Garantie).
Horaires
ouvrables : 7h00 à 17h00 du lundi au vendredi
Heure du Centre (CT)
(Horaires d’été : juin à septembre—
7h00 à 17h00 du lundi au jeudi
7h00 à 16h00 le vendredi)
Téléphone: 800-558-0607; 414-671-6350
Courriel: [email protected]
Service d'assistance et de pièces de
rechange disponible 7j/7, 24h/24 aux
États-Unis et au Canada en composant
le 800-558-0607.
Des renseignements supplémentaires sont disponibles sur
notre site Web à www.hatcocorp.com.
SOMMAIRE
Formulaire n° GR2SDM-0920
20
Français
CONSIGNES DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT
S’assurer que le produit alimentaire a été chauffé à une
température adaptée au maintien de sa salubrité avant de
le mettre dans l’appareil sous peine de risques graves pour
la santé. Cet appareil est destiné au maintien au chaud de
produits alimentaires préchauffés uniquement.
ATTENTION
DANGER DE BRÛLURE : Certaines surfaces extérieures
de l’appareil deviennent chaudes. Toucher ces zones de
l’appareil avec précaution.
Placer l’appareil sur un plan de travail de hauteur correcte
à un endroit qui convient pour son utilisation. Le support
doit être de niveau pour éviter toute chute accidentelle du
grille-pain ou de son contenu et suffisamment solide pour
résister au poids de l’appareil et de son contenu.
La National Sanitation Foundation (NSF) exige que les
appareils d’une largeur supérieure à 914 mm (36″) ou
pesant plus de 36 kg (80 lb) soient fixés sur le plan de
travail ou installés au-dessus de ce dernier. Si l’appareil
ne peut pas être fixé sur l’emplacement d’utilisation,
des pieds de 102 mm (4″) sont fournis pour permettre le
nettoyage en dessous de l’appareil.
AVIS
N’utilisez que des ampoules électriques qui correspondent
ou qui sont supérieures aux normes NSF et qui sont
spécifiquement conçues pour les espaces de conservation
des aliments. Les bris d’une ampoule électrique non
équipée d’un revêtement adapté peuvent provoquer
des dommages corporels et/ou une contamination des
aliments.
Ne couchez pas l’unité sur le côté comportant le panneau
de commande. L’appareil pourrait être endommagé.
Utiliser uniquement des produits nettoyants non abrasifs.
Les produits nettoyants abrasifs peuvent rayer la finition
de l’appareil, ce qui altère son apparence et le rend plus
susceptible d’accumuler la saleté.
Installer l’appareil dans une zone à l’écart des courants
d’air. Éviter les zones pouvant être soumises à des
mouvements d’air ou à des courants d’air actifs (c.-à-d. à
proximité des ventilateurs/hottes d’aspiration, des portes
et des conduites de climatisation).
IMPORTANT—N’utilisez PAS de serviettes en papier ou
de nettoyant pour vitres pour nettoyer les surfaces en
polycarbonate. Les serviettes en papier et le nettoyant
pour vitres peuvent rayer l’équipement. Essuyez les
surfaces en polycarbonate à l’aide d’un chiffon doux,
propre et humide.
AVERTISSEMENT
DANGER DE DÉCHARGE ÉLECTRIQUE :
• Brancher l’appareil sur une prise de courant avec terre
de tension, de format et de configuration des broches
corrects. Si la fiche et la prise ne se correspondent pas,
s’adresser à un électricien qualifié pour déterminer et
installer une prise de courant de format et de tension
corrects.
• Éteignez l’appareil et débranchez le cordon
d’alimentation de la prise secteur et laissez refroidir
avant une maintenance ou un nettoyage.
• NE PAS immerger l’appareil ni le saturer d’eau.
L’appareil n’est pas étanche à l’eau. Ne pas le faire
fonctionner s’il a été immergé ou saturé d’eau.
• L’appareil n’est pas à l’épreuve des intempéries. Placer
l’appareil à l’intérieur à une température ambiante de
21°C minimum.
• Ne pas nettoyer à la vapeur ni utiliser trop d’eau sur
l’appareil.
• Cet appareil n’est pas étanche aux jets. Ne pas utiliser
de jet sous pression pour nettoyer l’appareil.
• Ne pas nettoyer l’appareil lorsqu’il est sous tension.
• Cet appareil doit uniquement être réparé par un
personnel qualifié. Toute réparation par un personnel
non qualifié peut entraîner une électrocution et des
brûlures.
• Utilisez uniquement des pièces de rechange d’origine
Hatco lorsque l’entretien est nécessaire. Utilisez des
pièces détachées Hatco authentiques sous peine
d’annuler toutes les garanties et d’exposer l’utilisateur
à des tensions électriques dangereuses pouvant
entraîner une électrocution ou des brûlures. Les pièces
de rechange authentiques Hatco sont spécifiées pour
fonctionner en toute sécurité dans les environnements
dans lesquels elles sont utilisées. Certaines pièces de
rechange génériques ou d’après-vente n’ont pas les
caractéristiques qui leur permettent d’opérer en toute
sécurité dans les équipements Hatco.
DANGER D’INCENDIE: Placer l’appareil à un minimum
de 25 mm (1″) des parois et matières combustibles. Si
une distance sûre n’est pas maintenue, la chaleur peut
provoquer une combustion ou une altération de couleur.
RISQUE D’EXPLOSION: Ne pas conserver ou utiliser
d’essence ou d’autres vapeurs ou liquides inflammables à
proximité de cet appareil ou de tout autre dispositif.
Assurez-vous que tous les opérateurs ont été formés à
l’utilisation sûre et correcte de l’appareil.
Cet appareil ne contient aucune pièce réparable par
l’utilisateur. Si cet appareil doit être réparé, contacter un
réparateur Hatco agréé ou le Service après-vente Hatco au
800-558-0607 ou 414-671-6350.
Cet appareil ne doit pas être utilisé par des enfants ou des
personnes avec des capacités physiques, sensorielles ou
mentales diminuées. Assurez-vous que les enfants sont
bien surveillés et tenez-les à l’écart de l’appareil.
Lisez les consignes de sécurité importantes suivantes avant d’utiliser cet équipement pour éviter
toute blessure grave ou la mort et pour éviter d’endommager l’équipement ou la propriété.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
dans d''autres langues
- English: Hatco GR2SD Series User manual
Documents connexes
-
Hatco Glo-Ray GR2SDH-36 Le manuel du propriétaire
-
Hatco GR3SDH Le manuel du propriétaire
-
-
Hatco GR3SDH, GR3SDH-xxD, GR3SDS, GR3SDS-xxD Series Le manuel du propriétaire
-
-
-
-
-
-