Fanimation FP8404BN Le manuel du propriétaire

Marque: Fanimation

Modèle: FP8404BN

Catégorie: Ventilateurs ménagers

Taper: Le manuel du propriétaire

Ce manuel convient également à

Español p. 18

ATTACH YOUR RECEIPT HERE AND REGISTER YOUR FAN AT FANIMATION.COM

READ AND SAVE THESE INSTRUCTIONS

Serial Number

Purchase Date

MODEL #FP8404**

™

CEILING FAN

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-888-567-2055, 8 a.m.-5 p.m., EST, Monday-Friday.

Net Weight 20.90 lbs (9.48 kgs)

GLEAM

Important Safety Instructions

WARNING: To avoid fire, shock and serious personal injury, follow these instructions.

1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly

diagrams.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent

power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

warning device, such as a tag, to the service panel.

3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling

fan before servicing.

4. Do not insert anything into the fan blades while the fan is operating.

Additional Safety Instructions

1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without

blades.

2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70) and Local Codes. The

ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or

approved by a licensed electrician.

3. The fan base must be securely mounted and capable of reliably supporting at least 35 lbs. (fan and accessories not to

exceed 35 lbs. or 15.88 kgs.). See page 5 of owner’s manual for support requirements. Consult a qualified electrician if in

doubt.

4. The fan must be mounted with the fan blades at least 10 feet from the floor to prevent accidental contact with the fan blades.

5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate

electrical knowledge or experience, have your fan installed by licensed electrician.

6. Suitable for use with solid-state speed controls.

WARNING

TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS FAN MUST BE INSTALLED WITH A GENERAL USE,

ISOLATING WALL CONTROL/SWITCH.

WARNING

This product is designed to use only those parts supplied with this product and/or accessories designated

specifically for use with this product. Using parts and/or accessories not designated for use with this product could result in

personal injury or property damage.

WARNING

To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the

WARNING

Mount to an outlet box marked acceptable for fan support.

brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Please note that changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

5. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be

supervised to ensure that they do not play with the appliance.

8. For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be connected to a

grounded conductor power supply. If the conductor of a fan is identified as an ungrounded conductor, then it should be

connected to an ungrounded conductor power supply. If the conductor of a fan is identified for equipment grounding, then it

should be connected to an equipment-grounding conductor.

WARNING: Do not operate this fan with a variable (Rheostat) wall controller or dimmer switch. Doing so could result in damage

to the ceiling fan's remote control unit.

7. This fan is to be used in dry and damp locations.

LIMITED LIFETIME WARRANTY

Extends to the original purchaser of a Fanimation Fan

1. LIMITED LIFETIME MOTOR WARRANTY - If any part of your fan motor fails, due to a defect in materials or workmanship

during the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective

fan is returned to our national service center. Proof of purchase is required. Customer shall be responsible for all costs

incurred in the removal or reinstallation and shipping of the product for repairs or replacement.

2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due

to defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national service

center. Purchaser will be responsible for labor charges after this one-year period. Customer shall be responsible for all

costs incurred in the removal or reinstallation and shipping of the product for repairs or replacement.

3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or

workmanship, we will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our

national service center.

4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting,

corroding, tarnishing, or peeling.

5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to

extremes of heat or humidity, or as a result of any modification to the original product.

6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that

sold the fan or Fanimation.

7. Fanimation reserves the right to modify or discontinue any product at any time and may subst

itute any part under this

warranty.

9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other

expressed or implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to

those of merchantability and fitness for a particular purpose to the extent permitted by law. Some states do not allow

limitations on implied warranties. Fanimation will not be liable for incidental, consequential, or special damages arising out

of or in conjunction with product use or performance, except as may otherwise be accorded by law. This warranty gives you

special legal rights and you may also have other rights that vary from state to state.

10.A certain amount of wobble is normal and should not be considered a problem or a defect.

Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Energy Efficient Use of Ceiling Fans . . . . . . . . . . . . . . . . . . . . .5

Electrical and Structural Requirements . . . . . . . . . . . . . . . . . .5

How to Assemble Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .7

How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . .9

How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . 10

How to Install Your Canopy Housing . . . . . . . . . . . . . . . . . . . 11

Table of Contents

8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must

accompany authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be

properly

packed to avoid damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

How to Operate Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .12

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Exploded-View Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

How to Install Your Remote Control. . . . . . . . . . . . . . . . . . . . .13

This manual is designed to make it as easy as possible for you

to assemble, install, operate, and maintain your ceiling fan

Wiring outlet box and box connectors must be of type

required by local code. The minimum wire would be a 3-

conductor (2-wire with ground) of the following size:

NOTE: Place the parts from the loose parts bags in a small

container to keep them from being lost. If any parts are missing,

contact your local retailer.

Tools Needed for Assembly Materials

Wire Size A.W.G.Installed Wire Length

Up to 50 ft.

50 - 100 ft.

WARNING

Before assembling your ceiling fan, refer to section on

proper method of wiring your fan (page 10). If you feel you

do not have enough wiring knowledge or experience,

have your fan installed by a licensed electrician.

• One Phillips head screwdriver

• One 1/4˝ flat head screwdriver

• One stepladder

• One wire stripper • Four wire connectors

• One hex wrench

1. Check to see that you have received the following parts:

NOTE:

If you are uncertain of part description, refer to

exploded view illustration.

Unpacking Instructions

For your convenience, check-off boxes are provided next to each step. As each step is completed, place a check

mark in the box. This will insure that all steps have been completed and will be helpful in finding your place should

you be interrupted.

Do not install or use fan if any part is damaged or

missing. This product is designed to use only those

parts supplied with this product and/or any

accessories designated specifically for use with this

product by Fanimation. Substitution of parts or

accessories not designated for use with this product

by Fanimation could result in personal injury or

property damage.

Hanger Bracket

Assembly

Downrod/

Hanger Ball Assembly

Motor Assembly

Hardware Bags

Canopy Screw

Cover Assembly

Ceiling Cnopy

Motor Coupling

Cover Assembly

Hand-held

Remote

Receiver

Unit

NOTE:

Place the parts from the loose parts bags in a small

container to keep them from being lost. If any parts are

missing contact your local retailer.

– Wire Connectors

Energy Efficient Use of Ceiling Fans

Ceiling fan performance and energy savings rely

heavily on the proper installation and use of the ceiling

fan. Here are a few tips to ensure efficient product

performance.

Choosing the Appropriate Mounting Location

Ceiling fans should be installed, or mounted, in the middle

of the room and at least 10 feet above the floor and 18

inches from the walls. If ceiling height allows, install the fan

8 - 9 feet above the floor for optimal airflow. Consult your

Fanimation Retailer for optional mounting accessories.

Turn Off When Not in the Room

Ceiling fans cool people, not rooms. If the room is

unoccupied, turn off the ceiling fan to save energy.

Using the Ceiling Fan Year Round

Summer Season: Use the ceiling fan in the counter-

clockwise direction. The airflow produced by the ceiling

fan creates a wind-chill effect, making you “feel” cooler.

Select a fan speed that provides a comfortable breeze,

lower speeds consume less energy.

WinterSeason: Reverse the motor and operate the ceiling

fan at low speed in the clockwise direction. This produces

a gentle updraft, which forces warm air near the ceiling

down into the occupied space.Remember to adjust your

thermostat when using your ceiling fan - additional energy

and dollar savings could be realized with this simple step!

Electrical and Structural Requirements

Your new ceiling fan will require a grounded electrical

supply line of 120 volts AC, 60 HZ, 15 Amp Circuit.

Electrical code requires use of a fan-rated outlet box to

support the extra weight and motion associated with a

ceiling fan. A fan-rated box will be labeled as such and

typically supports up to a 70lb ceiling fan. Fan-Rated

Outlet Boxes vary in ratings and design. Ensure the

ratings of your ceiling fan outlet box meet the

requirements for the ceiling fan being installed. Figure 1,

Figure 2 and Figure 3 depicts different structural

configurations that may be used for mounting the

outlet box.

Low profile box (Figure 1)

A 1»2-in.-deep pancake box is meant to be screwed to a

joist or block. It’s used if only one cable is coming into

the box. It is also available in a saddle-mount

configuration.

CEILING

2" x 4"

CEILING JOIST

OUTLET BOX

Figure 1

Figure 2

2" x 4"

CEILING JOIST

CEILING

OUTLET BOX

Deep box (Figure 2)

A 2-1»-in.-deep box can be attached to blocking

between joists and is roomy enough to handle more

than one cable.

Electrical and Structural Requirements (Continued)

If your fan is to replace an existing light fixture, turn

electricity off at the main fuse box at this time and

remove the existing light fixture.

Turning off wall switch is not sufficient. To avoid

possible electrical shock, be sure electricity is

turned off at the main fuse box before wiring. All

wiring must be in accordance with National and

Local codes and the ceiling fan must be properly

grounded as a precaution against possible electrical

shock.

WARNING

Deep box with brace (Figure 3)

Paired with a deep box, this hanger is meant to span

between two joists and takes the place of wooden

blocking.

To avoid fire or shock, follow all wiring instructions

carefully. Any electrical work not described in these

instructionsshouldbedoneorapprovedby a

licensed electrician.

WARNING

Figure 3

CEILING JOIST

CEILING

OUTLET BOX

To reduce the risk of fire, electric shock, or personal

injury, mount to outlet box marked acceptable for fan

support of 15.9 kg (35 lbs) or less and use mounting

screws provided with the outlet box. Most outlet

boxes commonly used for the support of luminaires

are not acceptable for fan support and may need to be

replaced, consult a qualified electrician if in doubt.

Do not operate this fan with a variable (Rheostat)

wall controller or dimmer switch. Doing so could

result in damage to the ceiling fan's remote control

unit.

WARNING

Figure 1

How to Assemble Your Ceiling Fan

Downrod

Set Screw

Hanger Ball

1. Remove the hanger ball portion from the downrod/

hanger ball assembly by loosening the set screw in the

hanger ball until the ball falls freely down the downrod.

Remove the pin from the downrod, then remove the

hanger ball. Retain the pin and hanger ball for reinstal-

lation in Step 6. (Figure 1)

Remove the hairpin clip and clevis pin from the

bottom of the downrod. Retain the pin and clip for

reinstallation in Step 4. (Figure 2)

Figure 2

4. Slide downrod into the downrod support on top of

the motor. Install the clevis pin by aligning the holes

in the downrod support with holes in the downrod.

Secure clevis pin with hairpin clip. Install and tighten the

two set screws with nuts in the downrod support.

(Figure 4)

Figure 4

Downrod

Set Screws and

Locking Nuts (2)

Hairpin Clip

Figure 3

Black, White, Blue

wires and Safety Cable

3. Loosen the two set screws and locking nuts in

the downrod support of the motor assembly. Route

the black, white and blue wires and safety cable

through the downrod. (Figure 3)

Set Screws

and nuts (2)

Hairpin Clip

Clevis Pin

WARNING

It is critical that the clevis pin in the downrod support

is properly installed and the set screws and nuts are

securely tightened. Failure to do so could result in

the fan falling.

5. Route wires and safety cable through motor coupling

cover, canopy screw cover and ceiling canopy.

(Figure 5)

Motor Coupling

Cover

Ceiling

Canopy

Canopy Screw

Cover

6. Reinstall the hanger ball on the downrod as follows.

Route the black, white and blue wires and safety cable

through the hanger ball. Position the pin through

the two holes in the downrod and align the hanger

ball so the pin is captured in the groove in the top

of the hanger ball. Pull the hanger ball up tight

against the pin. Securely tighten the set screw in the

hanger ball. A loose set screw could create fan

wobble. (Figure 6)

How to Assemble Your Ceiling Fan (continued)

7. Cut off excess lead wire approximately 6 to 9 inches

above top of the downrod. Strip insulation off 1/2 inch

from the end of each lead wire. (Figure 7)

NOTE:

All set screws must be checked, and retightened

where necessary, before installation.

Figure 6

Figure 7

Figure 5

1. Using the

»8Ý x 2Ý lag bolt and flat washer, attach

safety cable to ceiling joist or wood structural member.

The lag bolt will pass through the flat washer, safety

cable loop, and into the building structure (Figure 3).

You will first drill a óÝ pilot hole into the building structure

to prevent splitting or cracking.

2. Securely attach the hanger bracket to ceiling junction

box acceptable for ceiling fan support..

NOTE: Ceiling support cable cannot be secured to

junction box only, it must be directly secured to ceiling

joist or structural member using the ǪÝ x 2Ý lag bolt and

À at washer. (Figure 3)

3. Make sure the electrical supply wires, including the

hanger bracket grounding wire and safety cable are

pulled through the downrod, between the hanger bracket

and the junction box so that electrical connections can be

made later.

Carefully lift the fan and seat the downrod/hanger ball

assembly on the hanger bracket that was just attached to

the ceiling joist. Be sure the groove in the ball is lined up

with tab on the hanger bracket. (Figure 4)

5. Attach the safety cable to ceiling support cable. Slide

cable clamp onto safety cable (from fan). Place the end

of cable through the loop of ceiling support cable. Pull as

much cable through loop as possible. Feed end of cable

into clamp hole and firmly tighten screw (Figure 4). Cut

off excess safety cable.

ÝÝ r

ÝÝ

À r.

WARNING

The fan must be hung with at least 10´ of clearance from

floor to blades. (Figure 2)

WARNING

The outlet box must be securely anchored and capable

of withstanding a load of at least 35 lbs. Hanger bracket

must seat

rmly against outlet box. If the outlet box is

recessed, remove wallboard until bracket contacts box.

If bracket and/or outlet box are not securely attached,

the fan could wobble or fall.

CAUTION

Do not connect fan blades until the fan is completely

installed. Hanging fan with blades connected may result

in damage to the fan blades.

WARNING

To avoid possible electrical shock, be sure electricity is

turned off at the main fuse box before hanging. (Figure 1)

NOTE: If you are not sure if the outlet box is grounded,

contact a licensed electrician for advice, as it must be

grounded for safe operation.

WARNING

Failure to seat tab in groove could cause damage to

electrical wires and possible shock or fire hazard.

How to Hang Your Ceiling Fan

Figure 2

%'+.+0)

(.114

01.'55

6*#0

(''6

Figure 1

/#+0(75'$1:

911&/'/$'4

r:r#2241:

%'+.+0),1+56

%'+.+0)

,70%6+10 

$1:

*#0)'4$4#%-'6

%'+.+0)

5722146

%#$.'

Figure 3

: 

HARDWARE USED:

Figure 4

6#$

016'5722.;9+4'5#0&(#0

9+4'51/+66'&(14%.#4+6;

&19041&*#0)'4

$#..#55'/$.;

#66#%*5#('6;

%#$.'61%'+.+0)

5722146%#$.'

%'+.+0)5722146

%#$.'%.#/2

95%4'9

To avoid possible shock, do not pinch wires

between the downrod/hanger ball assembly and the

hanger bracket.

WARNING

How to Wire Your Ceiling Fan

MAIN FUSE BOX

Figure 2

Figure 1

Figure 4

Green Wire

from Supply

(Ground)

White Wire

from Supply

White Wire

from Receiver

Green Wire

from Hanger

Bracket (Ground)

Green Wire

from Hanger

Ball (Ground)

Listed

Outlet Box

Household

Supply

Black Wire

from Supply

Black Wire

from Receiver

Receiver

Figure 3

x 6WIRE

CONNECTORS

HARDWARE USED:

ue to

k t

hit

all

To avoid possible electrical shock, be sure electricity is

turned off at the main fuse box before wiring. (Figure 2)

WARNING

NOTE:

If you are not sure if the outlet box is

grounded, contact a licensed electrician for advice, as

it must be grounded for safe operation.

Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire

connectors except for the ground wire. Do not

operate fan until the blades are in place. Noise and

motor damage could result.

WARNING

3. After connections have been made, turn leads

upward and carefully push leads into the outlet

box, with the white and green leads to one side

of the box and the black leads to the other side.

(Figure 4)

CAUTION: INCORRECT WIRE CONNECTION WILL

DAMAGE THIS RECEIVER.

2. Connect green wires from hanger bracket and

downrod to bare (ground) wire using wire connector.

Connect black wire from receiver unit marked “AC IN L”

to black supply wire using wire connector. Connect white

wire from receiver unit marked “AC IN N” to white supply

wire using wire connector. Connect white wire from

receiver unit marked “TO MOTOR N” to white wire from

fan using wire connector supplied with receiver unit.

Connect black wire from receiver unit marked “TO

MOTOR L” to black wire from fan using wire connector

supplied with receiver unit. Lastly, connect blue wire

from receiver unit to the blue fan light wire using wire

connector supplied with receiver unit. (Figure 3)

1. To set the code on receiver unit, slide dip switches to

the same positions as set on the remote. (Figure 1)

NOTE: The remote unit has 32 different code

combinations. To prevent possible interference from or to

other remote units, simply change the combination code

in the remote and receiver.

NOTE: Factory setting is all up. Do not use this position.

AVERTISSEMENT

Pour éviter tout risque d'électrocution, assurez-vous

que l'alimentation électrique est coupée au niveau du

boîtier à fusibles principal avant d'effectuer le câblage.

(Figure 2)

ATTENTION: UNE CONNEXION DE FIL INCORRECTE

PEUT ENDOMMAGER CE RECEPTEUR.

AVERTISSEMENT

Vérifiez que tous les raccordements sont bien

serrés, y compris la mise à la terre, et qu’aucun fil

dénudé n’est visible au niveau des capuchons de

connexion.Ne faites pas fonctionner le ventilateur

avant d'avoir installé les pales. Du bruit et des

dommages au moteur pourraient en résulter

Dip Switch

ON DIP

1 2 3 4 5

Receiver Unit

How to Install Your Canopy Housing

2. Securely attach and tighten the canopy screw cover

over the shoulder screws in the hanger bracket utilizing

the keyslot twist-lock feature. (Figure 2)

1. Remove one of the two shoulder screws in the

hanger bracket. Loosen the second shoulder screw

without fully removing it. Assemble canopy by

rotating key slot in canopy over shoulder screw in

hanger bracket. Tighten shoulder screw. Fully

assemble and tighten second shoulder screw that

was previously removed. (Figure 1)

WARNING

To avoid possible fire or shock, make sure that the

electrical wires are completely inside the canopy

housing and not pinched between the housing and the

ceiling.

NOTE: This step is applicable after the neccessary

wiring is completed.

Canopy Screw

Cover

Ceiling

Canopy

Figure 1

Figure 2

Figure 4

Dip Switch

ON DIP

1 2 3 4 5

Remote

How to Operate Your Ceiling Fan

2. Restore electrical power to the outlet box by turning

the electricity on at the main fuse box. (Figure 2)

Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire

connectors, except for the ground wire. Do not

operate fan until the blades are in place. Noise and

fan damage could result.

WARNING

1. IMPORTANT: Using a full range dimmer switch

(not included) to control fan speed will damage the fan.

To reduce the risk of fire or electrical shock, do not use

a full range dimmer switch to control the fan speed.

(Figure 1)

WARNING

Do not operate this fan with a variable (Rheostat) wall

controller or dimmer switch. Doing so could result in

damage to the ceiling fan's remote control unit.

MAIN FUSE BOX

Figure 2

Figure 1

For illustrative purposes only-not

intended to cover all types of controls

3. To make fan operational, install 23A/12V battery

(included) in hand-held remote transmitter, with fan

power off. Then follow the remote code setting

process. (If not used for long periods of time, remove

battery toprevent damage to transmitter). Store the

remote away from excessive heat or humidly.

(Figure 3)

4. To set the remote code with a small screwdriver or

ball point pen (neither included), slide dip switches firmly

up or down. (Figure 4)

NOTE: The remote unit has 32 different code

combinations. To prevent possible interference from or to

other remote units, simply change the combination code

in the remote and receiver.

NOTE: Factory setting is all up. Do not use this position.

12V 23A

Battery (1 pcs)

Figure 3

5. Remote functions: (Figure 5)

Figure 5

Maintenance

1. Periodic cleaning of your new ceiling fan is the only

maintenance that is needed. When cleaning, use

only a soft brush or lint free cloth to avoid

scratching the finish. Abrasive cleaning agents are

not required and should be avoided to prevent

damage to finish.

Do not use water when cleaning your ceiling fan.

It could damage the motor or the finish and create

the possibility of electrical shock.

CAUTION

How to Install Your Remote Control

Figure 1

1. Installing Wall Holder: (Figure 1)

Attach wall holder using the two provided screws.

How to Operate Your Ceiling Fan (continued)

6. If airflow is desired in the opposite direction, turn

the fan off and wait for the blades to stop turning.

Then slide the reverse switch on top of motor

assembly to the opposite position and turn fan on

again. (Figure 6 )

Reverse Switch Information

Season Rotation Direction Switch Position

Summer Counter-Clockwise

Left

Winter Clockwise

Right

Figure 6

Reverse Switch

For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan.

WARNING

Troubleshooting

Trouble Probable Cause Suggested Remedy

1.FAN WILL

NOT START

1. Check main and branch circuit fuses

or circuit breakers.

2. Check line wire connections to fan

and switch wire connections in the

switch housings.

CAUTION: Make sure main power is

turned off !

1. Fuse or circuit breaker blown.

2. Loose power line connections to the

fan, or loose switch wire connections

in the switch housing.

2.FAN SOUNDS NOISY

1. Check to make sure all screws in

motor housing are snug (do not

overtighten).

2. Check to make sure wire connectors

in switch housing are not rattling

against each other or against the

interior wall of the switch housing.

CAUTION: Make sure main power is

turned off !

3. Some fan motors are sensitive to

signals from solid-state variable

speed controls. Solid-state controls

are not recommended, choose an

alternative control method.

1. Loose screws in motor housing.

2. Wire connectors inside housing

rattling.

3. Motor noise caused by solid state

variable speed control.

3.FAN WOBBLES

EXCESSIVELY

1. Tighten both setscrews securely in

downrod support.

2. Tighten the setscrew in the downrod/

hanger ball assembly.

3. Tighten the hanger bracket screws to

the outlet box, and secure outlet box.

1. Setscrew in downrod support is loose.

2. Setscrew in downrod/hanger ball

assembly is loose.

3. Hanger bracket and/or ceiling outlet

box is not securely fastened.

4.NOT ENOUGH AIR

MOVEMENT

3. Dead battery in remote control. 3. Replace with new battery.

1. If possible, consider using a longer

downrod (not included, you can buy

the longer downrod from

fanimation.com).

4. Make sure reversing switch position is

all the way to one side.

4. Reversing switch in neutral position.

#traP noitpircseD # ecnerefeR

ADR1-45**

PG154**

APPAC1414**Motor Coupling Cover Assembly

AMA8404**Motor Assembly

TR500

RCCA04005000

AP255BL

AP260**

Receiver Unit

Hand-Held Remote

HDWFP8404

Hanger Bracket Assembly

Hanger Ball/Downrod Assembly

Ceiling Canopy

Canopy Screw Cover Assembly

Parts List

Model No. FP8404**

HOW TO ORDER REPAIR PARTS

When ordering repair parts, always give the following information:

Part Number

Part Description

Fan Model Number

Contact your retail store for repair parts.

Before discarding packaging material, be certain all parts have been removed.

** Insert FINISH CODES (Refer to fan model number located on downrod support)

Hardware Bag Containing:

Wire Connectors (4)

Bag Assembly Safety Cable

Model FP8404**

Exploded-View Illustration

NOTE: The illustration shown is not to scale or its actual con guration may vary.

Product/parts are subject to change without notice.

Figure 1

Gleam

™

7 8

2019/01 V.01

10983 Bennett Parkway

Zionsville, IN 46077

Phone: 888-567-2055

Outside U.S.: 317-733-4113

FANIMATION.COM

FAX: 866-482-5215

ADJUNTE SU RECIBO AQUÍ Y REGISTRE SU VENTILADOR EN FANIMATION.COM

LEA Y GUARDE ESTAS INSTRUCCIONES

Peso neto 9.48 kg (20.90 lbs)

Preguntas, problemas, piezas faltantes? Antes de volver a la tienda, llame a nuestro

Departamento de Servicio al Cliente al 1-888-567-2055, 8 a.m. - 5 pm, hora del Este, de

lunes - viernes.

Número de serie

Fecha de compra

MODELO #FP8404**

™

VENTILADOR DE TECHO GLEAM

ADVERTENCIA:

Instrucciones de seguridad importantes

ADVERTENCIA: Siga estas instrucciones para prevenir incendios, descargas eléctricas y lesiones personales graves.

Lea el manual del propietario y la información de seguridad antes de instalar su nuevo ventilador. Observe los diagramas de 1.

ensamblaje adjuntos.

Antes de llevar a cabo el mantenimiento o la limpieza de la unidad, desconecte la electricidad en el panel de servicio y bloquee los

medios de desconexión del mismo para evitar que se active accidentalmente. Si no se pueden bloquear los medios de desconexión

del servicio, coloque un dispositivo de advertencia, como una etiqueta, en el panel de servicio.

Tenga cuidado con la estructura y las aspas del ventilador cuando limpie, pinte o trabaje cerca del mismo. Desconecte siempre la

electricidad del ventilador de techo antes de llevar a cabo el mantenimiento.

No coloque nada en las aspas del ventilador cuando éste se encuentra en funcionamiento.

Instrucciones de seguridad adicionales

Para evitar posibles descargas eléctricas, asegúrese de que la electricidad esté desconectada en la caja de fusibles antes de realizar1.

la instalación eléctrica, y no haga funcionar el ventilador sin las aspas.

Todos los procedimientos de conexión eléctrica e instalación deben cumplir con los Códigos eléctricos nacionales (ANSI/NFPA

70) y Códigos locales. El ventilador de techo debe estar conectado a tierra a fin de prevenir posibles descargas eléctricas. La

instalación eléctrica debe ser llevada a cabo o aprobada por un electricista autorizado.

Se debe fijar bien la base del ventilador; ésta debe ser capaz de soportar sin problemas al menos 15,9 kg (35 lb). Consulte la página

22 del manual del propietario para ver los requisitos de soporte. Si tiene dudas, consulte a un electricista calificado.

Las aspas del ventilador deben instalarse por lo menos a 3 m (10 pies) del suelo, a fin de evitar un contacto accidental con las mismas.

Siga las recomendaciones sobre el método correcto de instalación eléctrica de su ventilador de techo. Si no posee la experiencia o 5.

los conocimientos eléctricos adecuados, contrate a un electricista autorizado para instalar el ventilador.

Apto para usar con controles de velocidad de estado sólido.

ADVERTENCIA: Monte a una caja de salida aceptable para apoyo de los aficionados.

PARA REDUCIR EL RIESGO DE DESCARGAS ELÉCTRICAS, ESTE VENTILADOR SE DEBE INSTALAR CON UN

CONTROL/INTERRUPTOR DE PARED AISLADO.

ADVERTENCIA: Este producto está diseñado para ser usado sólo con las piezas suministradas o los accesorios indicados

específicamente para el mismo. Si utiliza piezas o accesorios que no están indicados para su uso con este producto, podría

sufrir lesiones personales o dañar el ventilador. ADVERTENCIA: Este producto está diseñado para ser usado sólo con las piezas

suministradas o los accesorios indicados específicamente para el mismo. Si utiliza piezas o accesorios que no están indicados para su

uso con este producto, podría sufrir lesiones personales o dañar el ventilador.

ADVERTENCIA: Para reducir el riesgo de lesiones personales, no doble los soportes de las aspas (borde o soporte de aspas) al instalar

los soportes, balancear las aspas o limpiar el ventila

dor. No coloque objetos extraños entre las aspas del ventilador en funcionamiento.

(1) Este equipo no causará interferencias perjudiciales y (2) este equipo tolerará cualquier interferencia recibida, incluidas las

interferencias que puedan provocar un funcionamiento no deseado. Si el radiador intencional puede ser clasificado como un

dispositivo digital de clase B o un periférico del ordenador, entonces se deberán incluir los siguientes o equivalentes:

Nota: Tras someterlo a las pruebas correspondientes, se ha determinado que este equipo cumple con los límites establecidos para

dispositivos digitales de Clase B de conformidad con la parte 15 de la Normativa FCC. Estos límites se han establecido con el objetivo

de aportar una protección razonable contra interferencias perjudiciales cuando el equipo se utiliza en el hogar. Este equipo genera,

utiliza y puede emitir energía de radiofrecuencia y, a menos que se instale y se utilice de acuerdo con el manual de instrucciones, puede

provocar interferencias perjudiciales en las comunicaciones por radio y televisión. Si el equipo produce interferencias perjudiciales en la

recepción de radio o televisión, lo cual puede probarse encendiendo y apagando el equipo, se recomienda al usuario corregir dichas

interferencias tomando una o varias de las siguientes medidas:

- Modificar la orientación o ubicación de la antena de recepción;

- Aumentar la separación entre el equipo y el receptor;

- Conectar el equipo a una toma de corriente o circuito diferente al del receptor;

Consulte al distribuidor o a un técnico especialista de radio o TV para obtener más ayuda.

Nota: Para un dispositivo digital de clase A, la declaración de 15. 105(a) debe ser incluida cuando sea apropiada para el dispositivo en

cuestión.

5. El dispositivo no ha sido diseñador para ser utilizado por niños o personas enfermas sin supervisión. Los niños deben ser supervisados

para asegurarse de que no juegan con el dispositivo.

7. Este ventilador es apto sólo para lugares secos o húmedos.

8. En lo que respecta a las conexiones de suministro, si el conductor del ventilador está identificado como conductor con conexión a tierra,

se le debe conectar a un suministro de electricidad con conductor de puesta a tierra. Si el conductor del ventilador está identificado

como conductor que no es de puesta a tierra, se le debe conectar a un suministro de electricidad con conductor sin puesta a tierra.

Si el conductor del ventilador está identificado para equipos de puesta a tierra, se le debe conectar al conductor de equipos de puesta

a tierra.

ADVERTENCIA: No utilice este ventilador con un controlador variable de pared (Rheostat) o un regulador de intensidad. Si lo hiciera

podría dañar la unidad del mando a distancia del ventilador de techo.

AVERTISSEMENT: CE VENTILATEUR DOIT ÊTRE INSTALLÉ AVEC UNE COMMANDE/INTERRUPTEUR MURAL ISOLANT À

USAGE GÉNÉRAL AFIN DE RÉDUIRE LES RISQUES D'ÉLECTROCUTION.

AVERTISSEMENT: Ce produit est conçu pour utiliser uniquement les pièces l'accompagnant et/ou les accessoires spécifiquement

conçus pour ce produit. L'utilisation de pièces et/ou d'accessoires qui ne sont pas conçus pour être utilisés avec ce produit peut

provoquer des blessures ou des dommages matériels.

AVERTISSEMENT: Afin de réduire le risque de blessure, ne pliez pas le support de pale (bride ou porte-pale) lors de l'installation des

supports, de l'équilibrage des pales ou du nettoyage du ventilateur. N'insérez pas de corps étrangers entre les pales du ventilateur en

rotation.

AVERTISSEMENT:

AVERTISSEMENT: Montez sur une boîte de sortie indiquée comme étant acceptable pour supporter un ventilateur.

N'utilisez pas ce ventilateur avec un contrôleur mural (rhéostat) variable ou un gradateur. Cela pourrait endommager la

télécommande du ventilateur de plafond.

Este manual está diseñado para facilitar, en la medida de lo posible, el ensamblaje,

la instalación, el funcionamiento y el mantenimiento de su ventilador de techo

La caja de distribución eléctrica y los conectores de la caja

deben ser del tipo requerido por el código local. El cable más

pequeño debe ser un cable de tres conductores (de dos

conductores con conexión a tierra) del siguiente tamaño:

Herramientas necesarias para el ensamblaje

Materiales

longitud del cable instalado tamaño del cable según el A.W.G.

(Calibre de Alambre Estadounidense)

hasta 15,2 m (50 pies)

de 15,2 a 30,5 m (50 a 100 pies)

• Destornillador Phillips

• Escalera de tijera

• Destornillador de ¼˝

• Pelacables

•

Cuatro conectores de

cables

NOTA: coloque las piezas de las bolsas de piezas individuales

en un contenedor pequeño para evitar que se extravíen. Si faltan

piezas, póngase en contacto con su proveedor local.

ADVERTENCIA

Antes de ensamblar el ventilador de techo, consulte la

sección sobre el método correcto de instalación eléctrica del

ventilador (página 28). Si siente que no posee la experiencia

o los conocimientos eléctricos necesarios, contrate a un

electricista autorizado para instalar el ventilador.

Reportez-vous à la section sur la méthode appropriée

de câblage du ventilateur (page 28) avant d'assembler

votre ventilateur de plafond. Faites installer votre

ventilateur par un électricien agréé si vous pensez que

vous n'avez pas assez de connaissances ou d'expérience

en câblage.

AVERTISSEMENT

9. Se entiende que las reparaciones y las sustituciones son el único recurso disponible de Fanimation. No existe ninguna otra

garantía expresa o implícita. Por la presente, Fanimation niega todas las garantías implícitas, que incluyen, entre otras, la

comerciabilidad y la aptitud para determinado fin hasta donde la ley lo permita. Algunos estados no permiten limitaciones sobre las

garantías implícitas. Fanimation no se hará responsable por daños accidentales, resultantes o especiales derivados del uso o el

rendimiento del producto o en conjunción con éste, excepto en los casos en los que la ley así lo disponga. Esta garantía le otorga

derechos legales especiales y es posible que también goce de otros derechos que pueden variar según el estado.

10. Es normal que se produzca un cierto movimiento oscilante y esto no debe considerarse un problema o defecto.

7. Fanimation se reserva el derecho de modificar o discontinuar un producto en cualquier momento, o sustituir cualquier pieza según

lo establecido por esta garantía.

8. En ningún caso se podrá devolver un ventilador sin previa autorización por parte de Fanimation. Las devoluciones autorizadas

deberán ir acompañadas del recibo de venta y deberán enviarse a Fanimation, previo pago del flete. El ventilador que se devuelva

deberá estar embalado en forma adecuada a fin de evitar daños durante el transporte. Fanimation no se hará responsable de los

daños que resulten del embalaje incorrecto del producto.

Todos los gastos de remoción y reinstalación del ventilador son responsabilidad exclusiva del propietario, y no de la tienda que6.

vendió el ventilador ni de Fanimation.

Esta garantía es nula y no se aplica a daños por instalación incorrecta, negligencia, accidentes, uso indebido, exposición al calor o 5.

a la humedad en exceso, o como resultado de cualquier modificación realizada al producto original.

Debido a las diversas condiciones climáticas, esta garantía no cubre cambios en la terminación, incluidos oxidación, corrosión,4.

falta de brillo o peladuras.

GARANTÍA LIMITADA DE POR VIDA DEL MOTOR - Si se produjera una falla en alguna de las partes del motor de su ventilador debido 1.

a un defecto en los materiales o en la fabricación durante el tiempo de vida del comprador original, Fanim

ation proporcionará la pieza de

repuesto sin cargo una vez que el ventilador defectuoso sea devuelto a nuestro centro de servicios nacional. Se requiere comprobante de

venta. El cliente se hará responsable de todos los gastos de remoción o reinstalación y envío del producto para reparaciones o sustitución.

GARANTÍA DE MANO DE OBRA DEL MOTOR POR UN AÑO - Si el motor de su ventilador fallara antes de cumplirse un año a partir del 2.

momento de su compra original debido a defectos en los materiales o en la fabricación, se le efectuará la reparación del mismo sin cargo

en nuestro centro de servicios nacional. El comprador se hará responsable de los gastos de mano de obra luego del período de un año.

El cliente se hará responsable de todos los gastos de remoción o reinstalación y envío del producto pa

ra reparaciones o sustitución.

Si otra pieza del ventilador fallara dentro del período de un año a partir de la fecha de compra original debido a un defecto en los 3.

materiales o en la fabricación, repararemos o sustituiremos, según creamos conveniente, la pieza defectuosa sin cargo alguno en

nuestro centro de servicios nacional.

GARANTÍA LIMITADA DE POR VIDA

Se extiende al comprador original de un ventilador Fanimation

Tabla de contenidos

Instrucciones para el desempaque. . . . . . . . . . . . . . . . . . . . . . . . .....

............

Requisitos eléctricos y estructurales. . . . . . . . . . . . . . . . . . . ........

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . .

Cómo instalar la carcasa de la cubierta . . . . . . . . . . . . . . . . . . . . . . . .

........................

...........................

Cómo instalar su mando a distancia

...........................

Mantenimiento

.............................................

Solución de problemas . . . . . . . . . . . . . . . . . . . . ..................

Lista de piezas . . . . . . . . .....................................

Ilustración del despiece ........ ................. . . . .........

La page charge ...

Fanimation FP8404BN Le manuel du propriétaire

Marque: Fanimation

Modèle: FP8404BN

Catégorie: Ventilateurs ménagers

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Fanimation FP8404BN Owner's manual
español: Fanimation FP8404BN El manual del propietario

Fanimation FP8404BN Le manuel du propriétaire

Ce manuel convient également à

Fanimation FP8404BN Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents