Ryobi Trimmer 790r Manuel utilisateur

Marque: Ryobi

Modèle: Trimmer 790r

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

780r
790r

2-Cycle Gas Trimmer/Brushcutter

OPERATOR’S MANUAL

FOR QUESTIONS, CALL 1-800-345-8746 in U.S. or

1-800-668-1238 in CANADA

www.RyobiOutdoor.com

IMPORTANT MANUAL DO NOT THROW AWAY

780r

THANK YOU

Thank you for buying this quality product. This modern

outdoor power tool will provide many hours of useful

service. You will find it to be a great labor-saving device.

This operator’s manual provides you with easy-to-

understand operating instructions. Read the whole

manual and follow all the instructions to keep your new

outdoor power tool in top operating condition.

PRODUCT REFERENCES, ILLUSTRATIONS

AND SPECIFICATIONS

All information, illustrations and specifications in this

manual are based on the latest product information

available at the time of printing. We reserve the right to

make changes at any time without notice.

2003 MTD SOUTHWEST INC

Bump Head™ is a trademark of MTD SOUTHWEST INC.

SplitLine™ is a trademark of MTD SOUTHWEST INC.

SERVICE INFORMATION

Service on this unit both within and after the warranty

period should be performed only by an authorized and

approved service dealer.

• Call 1-800-345-8746 in the United States, or

1-800-668-1238 in Canada, to obtain a list of

authorized service dealers near you

• Go to www.RyobiOutdoor.com on the World Wide

Web for a list of authorized service dealers

DO NOT RETURN THE UNIT TO THE RETAILER.

NOTE: PROOF OF PURCHASE WILL BE REQUIRED

FOR WARRANTY SERVICE.

Make sure you carefully read and understand this

manual before starting or operating this equipment.

THIS PRODUCT IS COVERED BY ONE OR MORE

US PATENTS, OTHER PATENTS PENDING.

INTRODUCTION TABLE OF CONTENTS

I. California Proposition 65 Warning . . . . . . . . . . . . . . . . 3

II. Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . 3-7

A. Important Safety Information . . . . . . . . . . . . . . . . . 4

B. Safety and International Symbols . . . . . . . . . . . . . 6

C. Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

III. Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . 8-10

A. Install and Adjust the J handle . . . . . . . . . . . . . . . 8

B. Install the Harness . . . . . . . . . . . . . . . . . . . . . . . . . 8

C. Remove and Install the Attachment Shield . . . . . . .8

D. Remove the Cutting Attachment and

Install the Cutting Blade . . . . . . . . . . . . . . . . . . . . .9

E. Remove the Cutting Blade and

Install the Cutting Attachment . . . . . . . . . . . . . . . .10

IV. Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . . 11

V. Starting/Stopping Instructions . . . . . . . . . . . . . . . . . 12

VI. Operating Instructions . . . . . . . . . . . . . . . . . . . . 13-14

A. Holding the Trimmer . . . . . . . . . . . . . . . . . . . . . . 13

B. Adjusting Trimming Line Length . . . . . . . . . . . . . 13

C. Tips for Best Trimming Results . . . . . . . . . . . . . . 13

D. Decorative Trimming . . . . . . . . . . . . . . . . . . . . . . 14

E. Using the Cutting Blade . . . . . . . . . . . . . . . . . . . . .14

VII. Maintenance and Repair Instructions . . . . . . . . . 15-20

A. Maintenance Schedule . . . . . . . . . . . . . . . . . . . . 15

B. Line Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 15

C. Installing a Prewound Reel . . . . . . . . . . . . . . . . . 17

D. Air Filter Maintenance . . . . . . . . . . . . . . . . . . . . . 17

E. Spark Arrestor Maintenance . . . . . . . . . . . . . . . . .18

F. Carburetor Adjustment . . . . . . . . . . . . . . . . . . . . 19

G. Replacing the Spark Plug . . . . . . . . . . . . . . . . . . 19

H. Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

I. Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

J. Long Term Storage . . . . . . . . . . . . . . . . . . . . . . . .20

K. Accessories/Replacement Parts . . . . . . . . . . . . . .20

VIII.Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . 21

IX. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

X. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

XI. Parts List . . . . . . . . . . . . . . . . . . . . . .Inside Back Cover

CONTENTS OF CARTON

• Model 780r Trimmer/Brushcutter

∆ Large Bump Head Cutting Attachment

∆ 4-Tooth Brush Blade and Hardware

∆ J-Handle and Hardware

• Cutting Attachment Shield with Hardware

• Shoulder Harness

• Locking Rod Tool

•Operator's Manual

• Product Registration Card

• Bottle of 2-Cycle Oil

∆ This item will either be installed on the unit or in the

hardware pack

NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington. All U.S.

Forest Land and the state of California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by

law that certain internal combustion engines operated on forest brush and/or grass-covered areas be equipped with a

spark arrestor, maintained in effective working order, or the engine be constructed, equipped and maintained for the

prevention of fire. Check with your state or local authorities for regulations pertaining to these requirements. Failure to

follow these requirements could subject you to liability or a fine. This unit is factory equipped with a spark arrestor. If

it requires replacement, ask your LOCAL SERVICE DEALER to install the Accessory Part #182747 Spark Arrestor Kit.

Read the Operator’s Manual(s) and follow all warnings and safety instructions. Failure to do so

can result in serious injury to the operator and/or bystanders.

FOR QUESTIONS, CALL 1-800-345-8746 IN U.S. OR 1-800-668-1238 in CANADA

SPARK ARRESTOR

WARNING!

RULES FOR SAFE OPERATION

CALIFORNIA PROPOSITION 65 WARNING

WARNING

THE ENGINE EXHAUST FROM THIS

PRODUCT CONTAINS CHEMICALS

KNOWN TO THE STATE OF CALIFORNIA

TO CAUSE CANCER, BIRTH DEFECTS

OR OTHER REPRODUCTIVE HARM.

DANGER: Failure to obey a safety warning

will result in serious injury to yourself or to

others. Always follow the safety

precautions to reduce the risk of fire,

electric shock and personal injury.

WARNING: Failure to obey a safety

warning can result in injury to yourself and

others. Always follow the safety

precautions to reduce the risk of fire,

electric shock and personal injury.

CAUTION: Failure to obey a safety warning

may result in property damage or personal

injury to yourself or to others. Always follow

the safety precautions to reduce the risk of

fire, electric shock and personal injury.

SAFETY ALERT SYMBOL: Indicates

danger, warning or caution. Attention is

required in order to avoid serious personal

injury. May be used in conjunction with

other symbols or pictographs.

SYMBOL MEANING

The purpose of safety symbols is to attract your

attention to possible dangers. The safety symbols,

and their explanations, deserve your careful attention

and understanding. The safety warnings do not by

themselves eliminate any danger. The instructions or

warnings they give are not substitutes for proper

accident prevention measures.

NOTE: Advises you of information or instructions vital

to the operation or maintenance of the

equipment.

SYMBOL MEANING

READ ALL INSTRUCTIONS

BEFORE OPERATING

• Read the instructions carefully. Be familiar with the

controls and proper use of the unit.

• Do not operate this unit when tired, ill or under the

influence of alcohol, drugs or medication.

• Children under the age of 15 must not use the unit;

teens may operate the unit with adult guidance.

• Inspect the unit before use. Replace damaged parts.

Check for fuel leaks. Make sure all fasteners are in

place and secure. Replace cutting attachment parts

that are cracked, chipped or damaged in any way.

Make sure the cutting attachment is properly installed

and securely fastened. Be sure that the cutting

attachment shield is properly attached, and positioned

as recommended. Failure to do so can result in

personal injury to the operator and bystanders, as well

as damage to the unit.

• Use only 0.095 inch (2.41 mm) diameter Genuine

Factory Parts™ replacement line. Never use metal-

reinforced line, wire, chain or rope. These can break

off and become dangerous projectiles.

• Be aware of risk of injury to the head, hands and feet.

• Clear the area to be cut before each use. Remove

rocks, broken glass, nails, wire, string and other

objects which may be thrown or become entangled in

the cutting attachment. Clear the area of children,

bystanders and pets; keep them outside a 50-foot

(15 m.) radius, at a minimum. Even then, they are still

at risk from thrown objects. Encourage bystanders to

wear eye protection. If you are approached, stop the

unit immediately.

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments

or repairs before using the unit.

SAFETY WARNINGS FOR GAS TRIMMERS

• Store fuel only in containers specifically designed and

approved for the storage of such materials.

• IMPORTANT SAFETY INFORMATION •

• Always stop the engine and allow it to cool before

filling the fuel tank. Never remove the fuel tank cap or

add fuel when the engine is hot. Never operate the unit

without the fuel cap securely in place. Loosen the fuel

tank cap slowly to relieve any pressure in the tank.

• Add fuel in a clean, well-ventilated outdoor area where

there are no sparks or flames. Remove the fuel cap

slowly, and only after the engine stops. Do not smoke

while fueling or mixing fuel. Wipe up any spilled fuel

from the unit immediately.

• Avoid creating a source of ignition for spilled fuel. Do

not start the engine until fuel vapors dissipate.

• Move the unit at least 30 feet (9.1 m) from the fueling

source and site before starting the engine. Do not

smoke. Keep sparks and open flames away from the

area while adding fuel or operating the unit.

WHILE OPERATING

• Never start or run the unit inside a closed room or

building. Breathing exhaust fumes can be fatal.

Operate this unit only in a well-ventilated outdoor area.

• Wear safety glasses or goggles that meet ANSI Z87.1

standards and are marked as such. Wear ear/hearing

protection when operating this unit. Wear a face or

dust mask if the operation is dusty.

• Wear heavy long pants, boots, gloves and a long

sleeve shirt. Do not wear loose clothing, jewelry, short

pants, sandals or go barefoot. Secure hair above

shoulder level.

• The cutting attachment shield must always be in place

while operating the unit as a trimmer. Do not operate

unit without both trimming lines extended, and the

proper line installed. Do not extend the trimming line

beyond the length of the shield.

• This unit has a clutch. The cutting attachment remains

stationary when the engine is idling. If it does not, have

the unit adjusted by an authorized service technician.

• Adjust the J-handle to your size in order to provide the

best grip.

• Be sure the cutting attachment is not in contact with

anything before starting the unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Be in the starting position

whenever pulling the starter rope. The operator and

unit must be in a stable position while starting. Refer

to Starting/Stopping Instructions.

• Use the right tool. Only use this tool for its intended

purpose.

WARNING

When using the unit, you must

follow the safety rules. For your own safety

and that of bystanders, please read these

instructions before operating the unit.

Please keep the instructions for later use.

WARNING: Gasoline is highly flammable,

and its vapors can explode if ignited. Take

the following precautions:

RULES FOR SAFE OPERATION

• Do not overreach. Always keep proper footing and

balance.

• Always hold the unit with both hands when operating.

Keep a firm grip on both handles or grips.

• Keep hands, face, and feet at a distance from all

moving parts. Do not touch or try to stop the cutting

attachment when it rotates.

• Do not touch the engine, gear housing or muffler.

These parts get extremely hot from operation, even

after the unit is turned off.

• Do not operate the engine faster than the speed

needed to cut, trim or edge. Do not run the engine at

high speed when not cutting.

• Always stop the engine when cutting is delayed or

when walking from one cutting location to another.

• If you strike or become entangled with a foreign

object, stop the engine immediately and check for

damage. Do not operate before repairing damage. Do

not operate the unit with loose or damaged parts.

• Stop the unit, switch the engine to off, and disconnect

the spark plug for maintenance or repair.

• Use only Genuine Factory Parts™ replacement parts

and accessories for this unit. These are available from

your authorized service dealer. Use of any

unauthorized parts or accessories could lead to

serious injury to the user, or damage to the unit, and

void your warranty.

• Keep unit clean of vegetation and other materials.

They may become lodged between the cutting

attachment and shield.

• To reduce fire hazard, replace a faulty muffler and

spark arrestor. Keep the engine and muffler free from

grass, leaves, excessive grease or carbon build up.

WHILE OPERATING WITH CUTTING BLADE

• Read and understand all safety warnings before

operating this unit.

• Always use the shoulder harness when using the

brush blade accessory.

• Keep the J-handle between the operator and cutting

attachment or blade at all times.

• NEVER cut when the cutting blade is 30 inches

(76 cm) or more above the ground level.

• Blade thrust may occur when the spinning blade

contacts an object that it does not immediately cut.

Blade thrust can be violent enough to propel the unit

and/or operator in any direction, possibly causing a

loss of control. Blade thrust can occur without warning

if the blade snags, stalls or binds. This is more likely to

occur in areas where it is difficult to see the material

being cut.

• For operation with the brush blade, do not cut

anything thicker than 1/2 inch or a violent kickback

could occur.

• Do not attempt to touch or stop the blade when it is

rotating.

•A coasting blade can cause injury while it continues to

spin after the engine is stopped or the throttle trigger

is released. Maintain proper control until the blade has

completely stopped rotating.

• Do not run the unit at high speed when not cutting.

• If you strike or become entangled with a foreign

object, stop the engine immediately and check for

damage. Have any damage repaired before attempting

further operations. Do not operate unit with a bent,

cracked or dull blade. Discard blades that are bent,

warped, cracked or broken.

• Do not sharpen the cutting blade. Sharpening the blade

can cause the blade tip to break off while in use. This

can result in severe personal injury. Replace the blade.

• Do not use the cutting blade for edging or as an edger;

severe personal injury to yourself or others may incur.

Use the cutting blade only for the purpose described

in this manual.

• Stop the engine IMMEDIATELY if you feel excessive

vibration. Vibration is a sign of trouble. Inspect

thoroughly for loose nuts, bolts or damage before

continuing. Repair or replace affected parts as

necessary.

After Use

• Clean cutting blades with a household cleaner to

remove any gum buildup. Oil the blade with machine

oil to prevent rust.

• Lock up and store the cutting blade in an appropriate

area to protect the blade from unauthorized use or

damage.

OTHER SAFETY WARNINGS

• Never store a fueled unit inside a building where fumes

may reach an open flame or spark.

• Allow the engine to cool before storing or transporting.

Be sure to secure the unit while transporting.

• Store the unit in a dry area, locked up or up high to

prevent unauthorized use or damage, out of the reach

of children.

• Never douse or squirt the unit with water or any other

liquid. Keep handles dry, clean and free from debris.

Clean after each use, see Cleaning and Storage

instructions.

• Keep these instructions. Refer to them often and use

them to instruct other users. If you loan someone this

unit, also loan them these instructions.

SAVE THESE INSTRUCTIONS

RULES FOR SAFE OPERATION

SYMBOL MEANING

• ON/OFF STOP CONTROL

OFF or STOP

• THROWN OBJECTS AND

ROTATING CUTTER CAN

CAUSE SEVERE INJURY

WARNING: Do not operate without

the cutting attachment shield in place.

Keep away from the rotating cutting

attachment.

• HOT SURFACE WARNING

Do not touch a hot muffler, gear housing

or cylinder. You may get burned. These

parts get extremely hot from operation.

They remain hot for a short time after the

unit is turned off.

• SHARP BLADE

WARNING: Sharp blade on cutting

attachment shield. To prevent serious

injury, do not touch line cutting blade.

• BRUSHCUTTERS • REPLACE

DULL BLADE

Do not sharpen the cutting blade.

Sharpening the blade can cause the

blade tip to break off while in use. This

can result in severe personal injury.

•TRIMMER/BRUSHCUTTER

SAFETY

WARNING: Thrown objects and

rotating cutter can cause severe injury.

Keep bystanders, especially children

and pets, at least 50 feet (15 m) away

from the cutting area. The cutting

attachment shield must be used when

using the trimmer cutting attachment.

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning or caution.

May be used in conjunction with other

symbols or pictographs.

•WARNING - READ

OPERATOR'S MANUAL

Read the operator’s manual(s) and follow

all warnings and safety instructions.

Failure to do so can result in serious injury

to the operator and/or bystanders.

• WEAR EYE AND HEARING

PROTECTION

WARNING: Thrown objects and loud

noise can cause severe eye injury and

hearing loss. Wear eye protection

meeting ANSI Z87.1 standards and ear

protection when operating this unit.

Use a full face shield when needed.

•KEEP BYSTANDERS AWAY

WARNING: Keep all bystanders,

especially children and pets, at least

50 feet (15 m) from the operating area.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel.

• OIL

Refer to operator's manual for the

proper type of oil.

•ON/OFF STOP CONTROL

ON / START / RUN

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product.

Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

RULES FOR SAFE OPERATION

APPLICATIONS

As a trimmer:

• Cutting grass and light weeds

• Edging

• Decorative trimming around trees, fences, etc.

As a brushcutter:

• Cutting weeds and light bush of up to 1/2 inch in

diameter

Cutting Attachment Shield

Fuel Cap

Throttle

Control

J-Handle

Cutting Attachment

Gear Housing

Shaft Grip

Primer Bulb

Air Filter/Muffler

Cover

Spark Plug

On/Off Stop Control

Shaft

Housing

Starter Rope Grip

KNOW YOUR UNIT

Blade Shield /

Shield Mount

Cutting Blade

Line Cutting Blade

Muffler

Support Fitting

Throttle Lock-Out

Throttle Control

EZ-Start

Lever

ASSEMBLY INSTRUCTIONS

On some units, the J-handle may be pre-installed. In this

case you must loosen screws and adjust the handle to fit

the operator. Go to step 5 if the J-handle is pre-installed.

INSTALL AND ADJUST THE J-HANDLE

1. Place the J-handle between the top and middle

clamp pieces (Fig. 1).

(4) Screws

Top Clamp

J-Handle

Middle Clamp

Bottom Clamp

Nuts

2. While holding the three pieces together, install the four

(4) screws through the top clamp and into middle clamp.

NOTE: The holes in the top and middle clamp will line up

only when assembled correctly.

3. Place the clamps and the J-handle over the shaft

housing and onto the bottom clamp.

4. Hold each hex nut in the bottom clamp recess with a

finger. Start screws with a large Phillips screwdriver.

Do not tighten until you make the handle adjustment.

5. Slide the J-handle in or out until the arrow/white line on

the decal touches the clamp assembly (Fig. 2). You must

first loosen the screws if the handle is pre-installed.

Fig. 1

Fig. 2

Fig. 3

6. While holding the unit in the operating position (Fig. 3),

position the J-handle to the location that provides you

the best grip.

7. Tighten the clamp screws evenly, until the J-handle

is secure.

Decal

INSTALL THE HARNESS

1. Push the strap through the center of the buckle.

2. Pull the strap over the cross bar and down through

the slot in the buckle (Fig. 4).

3. Put the harness on over head and onto shoulder.

Snap it on to the support fitting (Fig. 5).

4. Adjust length to fit the operator’s size. Pull tab to

lengthen, pull strap to shorten (Fig 6).

Support Fitting

WARNING: Always use the shoulder

harness when using the cutting blade to

avoid serious personal injury.

Fig. 4

Fig. 5

Fig. 6

REMOVE AND INSTALL THE CUTTING

ATTACHMENT SHIELD

Remove the cutting attachment shield when

using the unit as a brushcutter

Remove the cutting attachment shield from the shield

mount by removing the three (3) screws with a flat blade

screwdriver (Fig. 7). Store parts for future use.

WARNING: The cutting attachment shield

should NOT be installed when operating

the unit with a blade. Remove the cutting

attachment shield before removing or

installing the blade.

Install the cutting attachment shield when using

the unit as a grass trimmer

Install the cutting attachment shield on the shield mount

by inserting the three (3) screws into the shield mount.

Tighten securely with a flat blade screwdriver (Fig. 7).

REMOVE THE CUTTING ATTACHMENT AND

INSTALL THE CUTTING BLADE

NOTE: To make cutting blade removal and installation easier,

place the unit on the ground or on a work bench

Remove the Cutting Attachment Shield

See Remove and Install the Cutting Attachment Shield.

Remove the Cutting Attachment

Align the shaft bushing hole with the locking rod slot and

insert the locking rod into the shaft bushing hole (Fig. 8).

(3) Screws

Cutting

Attachment

Shield

Shield Mount

Gear Housing

Fig. 7

ASSEMBLY INSTRUCTIONS

WARNING: The gear housing gets hot with

use. It can result in injury to the operator.

The housing remains hot for a short time

even after the unit is turned off. Do not

touch the gear housing until it has cooled.

WARNING: To avoid serious personal

injury, the cutting attachment shield MUST

be in place at all times while operating the

unit as a grass trimmer.

Cutting Attachment

Locking Rod

Slot

Locking Rod

Shaft Bushing Hole

Locking Rod Slot

Output Shaft

Bushing

Locking Rod

Output Shaft

2. Hold the locking rod in place by grasping it next to

the boom of the unit (Fig. 9).

3. While holding the locking rod, remove the cutting

attachment by turning it clockwise off of the output shaft

(Fig. 10). Store the cutting attachment for future use.

NOTE: The blade retainer under the cutting attachment

will be used when installing the cutting blade.

Fig. 8

Fig. 10

Fig. 9

Install the Cutting Blade

4. Place the cutting blade on the output shaft bushing

(Fig. 11).

WARNING: To avoid serious personal

injury, always wear gloves while handling or

installing the blade.

Shield

Mount

Locking Rod

Cutting

Blade

Blade Retainer

Nut

Output Shaft

Bushing

Pilot Hole

Fig. 11

Fig. 15

Fig. 12

Pilot Step

REMOVE THE CUTTING BLADE AND

INSTALL THE CUTTING ATTACHMENT

Remove the Cutting Blade

1. Align the shaft bushing hole with the locking rod slot

and insert the locking rod into the bushing hole (Fig. 8).

2. Hold the locking rod in place by grasping it next to

the boom of the unit (Fig. 14).

3. While holding the locking rod, loosen the nut on the

blade by turning it clockwise with a 5/8 inch closed-

end or socket wrench (Fig. 14).

Fig. 13

9. Remove the locking rod from the locking rod slot.

1/4-1/2 turn

Counterclockwise

6. Align the shaft bushing hole with the locking rod

slot and insert the locking rod into the bushing hole

(Fig. 8).

7. Put the blade retainer and nut on the output shaft.

Make sure that the blade is installed correctly.

8. Tighten nut counterclockwise against the blade while

holding the locking rod:

• If using a torque wrench and an 5/8 inch socket tighten

to: 325 - 335 in•lb, 27 - 28 ft.•lb, 37 - 38 N•m.

•Without a torque wrench, use a 5/8 inch closed-end or

socket wrench, turning the nut until the blade retainer

is snug against the shaft bushing. Make sure that the

blade is installed correctly, then rotate the nut an

additional 1/4 to 1/2 turn counterclockwise (Fig. 13).

Cutting Attachment

Locking Rod

Clockwise

6. Remove the locking rod.

7. Install the cutting attachment shield. Refer to Remove

and Install the Cutting Attachment Shield.

Blade Retainer

Output Shaft

Bushing

Fig. 14

WARNING: To avoid serious personal

injury or damage to the unit, do not start or

operate this unit with the locking rod in the

locking rod slot.

WARNING: To avoid serious personal

injury, always wear gloves while handling or

installing the blade.

WARNING: Do not sharpen the cutting blade.

Sharpening the blade can cause the blade tip

to break off while in use. This can result in

severe personal injury. Replace the blade.

ASSEMBLY INSTRUCTIONS

WARNING: To avoid serious personal injury,

the cutting head guard MUST be in place at

all times while operating the unit as a trimmer.

5. Make sure that the cutting blade is centered on the

pilot step and sitting flat against the output shaft

bushing (Fig. 12).

WARNING: If the cutting blade is off-

center, the unit will vibrate and the blade

may fly off, causing possible serious

personal injury.

4. Remove the nut, blade retainer and blade. Store the

nut and blade together for future use in a secure

place. Store out of children’s reach.

Install the Cutting Attachment

Align the shaft bushing hole with the locking rod slot and

insert the locking rod into the shaft bushing hole (Fig. 8).

Place the blade retainer on the output shaft with the flat

surface against the output shaft bushing (Fig. 15). Screw

the cutting attachment counterclockwise onto the output

shaft. Tighten securely.

NOTE: The blade retainer must be installed on the output

shaft in the position shown for the cutting

attachment to work correctly.

OIL AND FUEL INFORMATION

NOTE: Dispose of the old fuel/oil mix in accordance to

Federal, State and Local regulations.

CAUTION: For proper engine operation and

maximum reliability, pay strict attention to

the oil and fuel mixing instructions on the

2-cycle oil container. Using improperly

mixed fuel can severely damage the engine.

WARNING: Gasoline is extremely

flammable. Ignited Vapors may explode.

Always stop the engine and allow it to cool

before filling the fuel tank. Do not smoke

while filling the tank. Keep sparks and open

flames at a distance from the area.

WARNING: Remove fuel cap slowly to avoid

injury from fuel spray. Never operate the unit

without the fuel cap securely in place

WARNING: Add fuel in a clean, well

ventilated area outdoors. Wipe up any

spilled fuel immediately. Avoid creating a

source of ignition for spilt fuel. Do not start

the engine until fuel vapors dissipate.

OIL AND FUEL MIXING INSTRUCTIONS

Old and/or improperly mixed fuel are the main reasons

for the unit not running properly. Be sure to use fresh,

clean unleaded fuel. Follow the instructions carefully for

the proper fuel/oil mixture.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and

oxygenates such as ethanol, methanol, or MTBE (ether).

Alcohol-blended fuel absorbs water. As little as 1%

water in the fuel can make fuel and oil separate. It forms

acids when stored. When using alcohol-blended fuel,

use fresh fuel (less than 60 days old).

Using Blended Fuels

If you choose to use a blended fuel, or its use is

unavoidable, follow recommended precautions:

• Always use the fresh fuel mix explained in your

operator's manual

• Always agitate the fuel mix before fueling the unit

• Drain the tank and run the engine dry before storing

the unit

Using Fuel Additives

The bottle of 2-cycle oil that came with your unit

contains a fuel additive which will help inhibit corrosion

and minimize the formation of gum deposits. It is

recommended that you use our 2-cycle oil with this unit.

If unavailable, use a good 2-cycle oil designed for

air-cooled engines along with a fuel additive, such as

STA-BIL

Gas Stabilizer or an equivalent. Add 0.8 oz.

(23 ml.) of fuel additive per gallon of fuel according to the

instructions on the container. NEVER add fuel additives

directly to the unit's fuel tank.

Thoroughly mix the proper ratio of 2-cycle engine oil

with unleaded gasoline in a separate fuel can. Use a 40:1

fuel/oil ratio. Do not mix them directly in the engine fuel

tank. See the table below for specific gas and oil mixing

ratios.

NOTE: One gallon (3.8 liters) of unleaded gasoline mixed

with one 3.2 oz. (95 ml.) bottle of

2-cycle oil makes a 40:1 fuel/oil ratio.

UNLEADED GAS 2 CYCLE OIL

1 US. GALLON + 3.2 FL. OZ.

(3.8 LITERS) (95 ml)

1 LITER + 25 ml

MIXING RATIO - 40:1

STARTING/STOPPING INSTRUCTIONS

Fig. 16

Fig. 17

On/Off Stop Control

Start/On (I)

Stop/Off (O)

Throttle Lock-Out

Throttle Control

Starter Rope

Throttle Control

STOPPING INSTRUCTIONS

1. Release your hand from the throttle control (Fig. 18).

Allow the engine to cool down by idling.

2. Put the On/Off Stop Control in the OFF (O) position

(Fig. 16).

Primer Bulb

EZ-Start™

Lever

Fig. 18

STARTING INSTRUCTIONS

1. Mix gas with oil. Fill fuel tank with fuel/oil mixture.

Refer to Oil and Fuel Mixing Instructions.

2. Make sure the On/Off Stop Control is in the ON (I)

position (Fig. 16).

3. Fully press and release the primer bulb 10 times,

slowly, until FUEL IS VISIBLE IN THE PRIMER

BULB (Fig. 17). If you can’t see fuel in the bulb, press

and release the bulb as many times as it takes before

you can see fuel in it.

4. Push the EZ-Start™ Lever to the left until it clicks and

locks into place (Fig. 17).

5. While the unit is in the starting position (Fig. 18), DO

NOT SQUEEZE THE THROTTLE CONTROL. Pull the

starter rope briskly 5 times, making sure the EZ-Start™

lever is pushed to the left. If the engine starts to run

before the fifth pull, proceed to step 6. If the engine

does not start, go back to step 3.

NOTE: When starting, the EZ-Start™ Lever will

automatically click off when you squeeze the

throttle control.

NOTE: If the outside temperature or engine temperature

exceeds 90º F and the engine fails to start after 5

pulls, fully squeeze the throttle control and pull

the starter rope briskly 3 to 8 more times. The

engine should start within these pulls.

6. Squeeze the throttle control for 5 to 10 seconds in

order to warm up the engine. The EZ-Start™ Lever

will click off automatically (Fig. 17).

NOTE: if the engine stalls before you squeeze the throttle

control, hold the throttle control and pull the

starter rope until the trimmer starts.

NOTE: If the engine stalls while squeezing the throttle,

go back to step 4.

NOTE: To start a warm engine, begin at step 4.

WARNING:

Operate this unit only in a well-

ventilated outdoor area. Carbon monoxide

exhaust fumes can be lethal in a confined area.

WARNING: Avoid accidental starting. Make

sure you are in the starting position when

pulling the starter rope (Fig. 18).

To avoid

serious injury, the operator and unit must be

in a stable position while starting.

HOLDING THE TRIMMER

Before operating the unit, stand in the operating position

(Fig. 19). Check for the following:

• The operator is wearing eye protection and proper

clothing

• With a slightly-bent right arm, the operator’s right hand

is holding the shaft grip

• The operator’s left arm is straight, the left hand holding

the J-handle

• The unit is at waist level

• The cutting attachment is parallel to the ground and

easily contacts the grass without the need to bend over

Once you are in the operating position, hook the

shoulder strap to the unit.

WARNING: Always wear eye, hearing, foot

and body protection to reduce the risk of

injury when operating this unit.

OPERATING INSTRUCTIONS

Fig. 19

ADJUSTING TRIMMING LINE LENGTH

The Bump Head™ cutting attachment allows you to

release trimming line without stopping the engine. To

release more line, lightly tap the cutting attachment on the

ground (Fig. 20) while operating the trimmer at high speed.

NOTE: Always keep the trimming line fully extended.

Line release becomes more difficult as the cutting

line becomes shorter.

Fig. 20

Each time the head is bumped, about 1 inch (25.4 mm) of

trimming line is released. A blade in the cutting

attachment shield will cut the line to the proper length if

excess line is released.

For best results, tap the Bump Head™ on bare ground or

hard soil. If line release is attempted in tall grass, the

engine may stall. Always keep the trimming line fully

extended. Line release becomes more difficult as the

cutting line becomes shorter.

NOTE: Do not rest the Bump Head™ on the ground

while the unit is running.

Some line breakage will occur from:

• Entanglement with foreign matter

• Normal line fatigue

• Attempting to cut thick, stalky weeds

• Forcing the line into objects such as walls or fence posts

TIPS FOR BEST TRIMMING RESULTS

• For best trimming results, operate unit at full throttle.

• Keep the cutting attachment parallel to the ground.

• Do not force the cutting attachment. Allow the tip of

the line to do the cutting, especially along walls.

Cutting with more than the tip will reduce cutting

efficiency and may overload the engine.

• Cut grass over 8 inches (200 mm) by working from top

to bottom in small increments to avoid premature line

wear or engine drag.

• Cut from left to right whenever possible. Cutting to the

right improves the unit's cutting efficiency. Clippings

are thrown away from the operator.

• Slowly move the trimmer into and out of the cutting

area at the desired height. Move either in a forward-

backward or side-to-side motion. Cutting shorter

lengths produces the best results.

• Trim only when grass and weeds are dry.

• The life of your cutting line is dependent upon:

•Following the previously-explained trimming techniques

• What vegetation is cut

• Where vegetation is cut

For example, the line will wear faster when trimming against

a foundation wall as opposed to trimming around a tree.

CAUTION:

Do not remove or alter the line

cutting blade assembly. Excessive line length

will make the clutch overheat. This may lead to

serious personal injury or damage to the unit.

Fig. 21

Fig. 22

Fig. 23

DECORATIVE TRIMMING

Decorative trimming is accomplished by removing all

vegetation around trees, posts, fences and more.

Rotate the whole unit so that the cutting attachment is at

a 30° angle to the ground (Fig. 21).

USING THE CUTTING BLADE

Before operating the unit with the cutting blade, stand in

the operating position (Fig. 22). Refer to Holding the

Trimmer.

Cutting Blade Operating Tips

To establish a rhythmic cutting procedure:

• Plant feet firmly, comfortably apart.

• Bring the engine to full throttle before entering the

material to be cut. At full throttle the blade has

maximum cutting power and is less likely to bind, stall

or cause blade thrust (which can result in serious

personal injury to the operator or others).

• Cut while swinging the upper part of your body from

left to right.

• Always release the throttle trigger and allow the engine

to return to idle speed when not cutting.

• When you are finished, always unsnap the unit from

the harness before taking off the harness.

• Swing the unit in the opposite direction that the blade

spins, which increases the cutting action.

• After the return swing, move forward to the next area

to be cut plant your feet again.

• The cutting blade is designed with a second cutting

edge. You can use it by removing the blade, turning it

upside down, and reinstalling it.

To reduce the chance of material wrapping around the

blade, follow these steps:

• Cut at full throttle

• Swing the unit into material to be cut from your left to

your right (Fig. 23)

• Avoid the material just cut as you make the return swing

OPERATING INSTRUCTIONS

WARNING: Always wear eye, hearing, foot,

body protection and the shoulder strap to

reduce the risk of injury when operating this unit.

WARNING: Do not clear away any cut

material with the engine running or blade

turning. To avoid serious personal injury,

turn off the engine. Allow the blade to stop

before removing materials wrapped around

the blade shaft.

WARNING: Do not sharpen the cutting

blade. Sharpening the blade can cause the

blade tip to break off while in use. This can

result in severe personal injury to yourself

or others. Replace the blade.

WARNING: The blade continues to spin after

the engine is turned off. The coasting blade

can seriously cut you if accidentally touched.

WARNING: Blade thrust may occur when

the spinning blade contacts an object that

it does not immediately cut. Blade thrust

can be violent enough to cause the unit

and/or operator to be propelled in any

direction, and possibly lose control of the

unit. Blade thrust can occur without

warning if the blade snags, stalls or binds.

This is more likely to occur in areas where it

is difficult to see the material being cut.

WARNING: Do not use the cutting blade

for edging or as an edger. Severe personal

injury to yourself or others can result.

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the

frequency stated in the table. These procedures should

also be a part of any seasonal tune-up.

NOTE: Some maintenance procedures may require

special tools or skills. If you are unsure about

these procedures take your unit to any non-road

engine repair establishment, individual or

authorized service dealer.

NOTE: Maintenance, replacement, or repair of the

emission control devices and system may be

performed by any non-road engine repair

establishment, individual or authorized service

dealer.

In order to assure peak performance of your engine,

inspection of the engine exhaust port may be necessary

after 50 hours of operation. If you notice lost RPM, poor

performance or general lack of acceleration, this service

may be required. If you feel your engine is in need of this

inspection, refer service to any non-road engine repair

establishment, individual or authorized service dealer for

repair. DO NOT attempt to perform this process yourself

as engine damage may result from contaminants

involved in the cleaning process for the port.

FREQUENCY MAINTENANCE REQUIRED REFER TO

Before starting engine Fill fuel tank with fresh fuel Page 11

Every 10 hours Clean and re-oil air filter Page 17

Every 25 hours

Check and clean spark arrestor

Check spark plug condition and gap

Page 18

Page 19

Every 50 hours

Inspect exhaust port and spark arrestor screen for clogging or

obstruction to assure maximum performance levels

Page 18

MAINTENANCE AND REPAIR INSTRUCTIONS

WARNING: To prevent serious injury, never

perform maintenance or repairs with unit

running. Always service and repair a cool unit.

Disconnect the spark plug wire to ensure that

the unit cannot start.

Indexing Teeth

Fig. 25

Fig. 26

LINE INSTALLATION

This section covers both SplitLine™ and standard single

line installation.

Always use Genuine Factory Parts™ 0.095 in. (2.41 mm)

replacement line. Line other than the specified may make

the engine overheat or fail.

There are two methods to replace the trimming line:

• Wind the inner reel with new line

• Install a prewound inner reel

Winding the Existing Inner Reel

1. Hold the outer spool with one hand and unscrew the

Bump Knob clockwise (Fig. 24). Inspect the bolt inside

the bump knob to make sure it moves freely. Replace

the bump knob if damaged.

2. Remove the inner reel from the outer spool (Fig. 24).

3. Remove spring from the inner reel (Fig. 24).

4. Use a clean cloth to clean the the inner reel, spring,

shaft and inner surface of the outer spool (Fig. 25).

5. Check the indexing teeth on the inner reel and outer

spool for wear (Fig. 26). If necessary, remove burrs or

replace the reel and spool.

Inner Reel

Spring

Outer Spool

Bump Knob

Bolt

Fig. 24

WARNING: Never use metal-reinforced

line, wire, chain or rope. These can break

off and become dangerous projectiles.

MAINTENANCE AND REPAIR INSTRUCTIONS

Fig. 28

Fig. 29

Fig. 30

Fig. 31

Fig. 32

Fig. 27

NOTE: SplitLine™ can only be used with the inner reel

with the slotted holes. Single line can be used on

either type of inner reel. Use Figure 27 to identify

the inner reel you have.

NOTE: Always use the correct line length when installing

trimming line on the unit. The line may not release

properly if the line is too long.

Single Line Installation

Go To Step 8 for SplitLine™ Installation

6. Take approximately 40 feet (12.2 m) of new trimming

line, loop it into two equal lengths. Insert each end of

the line through one of the two holes in the inner reel

(Fig. 28). Pull the line through the inner reel so that

the loop is as small as possible.

7. Wind the lines in tight even layers, onto the reel

(Fig. 29). Wind the line in the direction indicated on

the inner reel. Place your index finger between the

two lines to stop the lines from overlapping. Do not

overlap the ends of the line. Proceed to step 11.

Spring

SplitLine™ Installation

8. Take approximately 20 feet (6.1 m) of new trimming

line. Insert one end of the line through one of the two

holes in the inner reel (Fig. 30). Pull the line through

the inner reel until only about 4 inches is left out.

9. Insert the end of the line into the open hole in the

inner reel and pull the line tight to make the loop as

small as possible (Fig. 30).

10. Before winding, split the line back about 6 inches.

11. Wind the line in tight even layers in the direction

indicated on the inner reel.

NOTE: Failure to wind the line in the direction indicated will

cause the cutting attachment to operate incorrectly.

Loop

Slotted

Holes

For Use with SplitLine™

or Single Line

For Use with Single

Line ONLY

Loop

Holding Slots

NOTE: The spring must be assembled on the inner reel

before reassembling the cutting attachment.

14. Hold the inner reel in place and install the bump knob

by turning counterclockwise. Tighten securely.

12. Insert the ends of the line into the two holding slots

(Fig. 31).

13. Insert the ends of the line through the eyelets in the

outer spool and place inner reel with spring inside the

outer spool (Fig. 32). Push the inner reel and outer

spool together. While holding the inner reel and outer

spool, grasp the ends and pull firmly to release the

line from the holding slots in the reel.

MAINTENANCE AND REPAIR INSTRUCTIONS

Fig. 33

AIR FILTER MAINTENANCE

Removing the Air Filter/Muffler Cover

1. Remove the four (4) screws securing the air

filter/muffler cover (Fig. 33). Use a flat blade or

T-20 Torx bit screwdriver.

2. Pull the cover from the engine. Do not force.

Screws

INSTALLING A PREWOUND REEL

1. Hold the outer spool with one hand and unscrew the

bump knob clockwise (Fig. 24). Inspect the bolt inside

the bump knob to make sure it moves freely. Replace

the bump knob if damaged.

2. Remove the old inner reel from the outer spool

(Fig. 24).

3. Remove the spring from the old inner reel

(Fig. 24).

4. Place the spring in the new inner reel.

NOTE:The spring must be assembled on the inner reel

before reassembling the cutting attachment.

5. Insert the ends of the line through the eyelets in the

outer spool (Fig. 32).

6. Place the new inner reel inside the outer spool. Push the

inner reel and outer spool together. While holding the

inner reel and outer spool, grasp the ends and pull firmly

to release the line from the holding slots in the spool.

7. Hold the inner reel in place and install the bump knob

by turning counterclockwise. Tighten securely.

Replacement Parts

See Accessories / Replacement Parts.

WARNING: To avoid serious personal injury,

always turn your trimmer off and allow it to

cool before you clean or service it.

Cleaning the Air Filter

Clean and re-oil the air filter every 10 hours of operation.

It is an important item to maintain. Failure to maintain the

air filter will VOID the warranty.

1. Remove air filter/muffler cover. Refer to Removing

the Air Filter/Muffler Cover.

2. Turn cover over and look inside to locate the air filter.

Remove the air filter from inside the air filter/muffler

cover (Fig. 34).

3. Wash the filter in detergent and water (Fig. 35). Rinse

the filter thoroughly. Squeeze out excess water. Allow

it to dry completely.

4. Apply enough clean SAE 30 oil to lightly coat the filter

(Fig. 36).

5. Squeeze the filter to spread and remove excess oil

(Fig. 37).

Fig. 34

Fig. 35

Fig. 36

Fig. 37

6. Replace the air filter inside the air filter/muffler cover

(Fig. 34).

NOTE: Operating the unit without the air filter and air

filter/muffler cover assembly will VOID the

warranty.

Air Filter

Inside Muffler

Cover

EZ-Start™

Lever

Reinstalling the Air Filter/Muffler Cover

1. Place the air filter/muffler cover over the back of the

carburetor and muffler. Align the screw holes.

2. Insert the four (4) screws into the holes in the air

filter/muffler cover (Fig. 33) and tighten.

Do not over tighten.

SPARK ARRESTOR MAINTENANCE

1. Remove air filter/muffler cover. Refer to Removing

the Air Filter/Muffler Cover.

2. Locate muffler front and the two (2) bolts securing it

to the engine (Fig. 38). Remove the two (2) bolts

using a flatblade screwdriver or 5/16-inch socket or

nut driver. Pull muffler off of the engine.

3. Turn muffler over to the back side and locate the

exhaust gasket. Remove the muffler gasket from the

muffler (Fig. 38).

NOTE: If the exhaust gasket is torn or damaged, replace

it with a new gasket before reassembling muffler.

4. Using a small flatblade screwdriver, carefully pry up

the spark arrestor from the recessed hole (Fig. 39).

Remove the spark arrestor from the muffler.

5. Clean the spark arrestor with a wire brush. Replace it

if it is damaged or if it is impossible to clean

thoroughly (Fig. 39).

6. Reinstall the spark arrestor by pressing it into the

recessed hole on the muffler's back side. Make sure

it fits tightly against the muffler and is not raised up.

7. Place the exhaust gasket against muffler's back side.

Align the gasket bolt holes with the bolt holes in the

muffler. While holding exhaust gasket in place, insert

the bolts into the muffler's front side (Fig. 38).

8. Place the muffler (with the exhaust gasket in place

and bolts inserted), against the engine, aligning the

bolt holes. Tighten the bolts to secure the muffler to

the engine.

If using a torque wrench, torque to:

80-90 in.•lb. (9-10.2 N•m)

9. Reinstall the air filter/muffler cover.

Fig. 39

Fig. 38

Muffler - Front Side

Muffler - Back Side

Bolts

Exhaust

Gasket

Spark

Arrestor

Muffler - Back Side

Spark

Arrestor

Flatblade

Screwdriver

Spark Arrestor

WARNING:

If the muffler is not tightened

securely, it could fall off causing damage to

the unit and possible serious personal injury

MAINTENANCE AND REPAIR INSTRUCTIONS

Check Fuel Mixture

Old and/or improperly mixed fuel is usually the reason

for improper unit performance. Drain and refill the tank

with fresh, properly-mixed fuel prior to making any

adjustments. Refer to Oil and Fuel Information.

Clean Air Filter

The condition of the air filter is important to the operation

of the unit. A dirty air filter will restrict air flow and

change the air/fuel mixture. This is often mistaken for an

out of adjustment carburetor. Check the condition of the

air filter before adjusting the idle speed screw. Refer to

Air Filter Maintenance.

Adjust Idle Speed Screw

If, after checking the fuel mixture and cleaning the air

filter, the engine still will not idle, adjust the idle speed

screw as follows:

1. Start the engine and let it run at a high idle for a

minute to warm up. Refer to Starting/Stopping

Instructions.

2. Release the throttle trigger and let the engine idle. If

the engine stops, insert a small phillips or flat blade

screwdriver into the hole in the air filter/muffler cover

(Fig. 40). Turn the idle speed screw in, clockwise,

1/8 of a turn at a time (as needed) until the engine

idles smoothly.

CARBURETOR ADJUSTMENT

The idle speed of the engine is adjustable through the air

filter/muffler cover (Fig. 40).

NOTE: Careless adjustments can seriously damage your

unit. An authorized service dealer should make

carburetor adjustments.

Fig. 40

Idle Speed Screw

NOTE: The cutting attachment should not rotate when

the engine idles.

3. If the cutting attachment rotates when the engine

idles, turn the idle speed screw counterclockwise

1/8 of a turn at a time (as needed), to reduce idle

speed.

Checking the fuel mixture, cleaning the air filter, and

adjusting the idle speed should solve most engine

problems. If not and:

• the engine will not idle

• the engine hesitates or stalls on acceleration

• there is a loss of engine power

Have the carburetor adjusted by an authorized service

dealer.

REPLACING THE SPARK PLUG

Use a Champion RDJ7Y spark plug, or equivalent. The

correct air gap is 0.020 inch (0.5 mm). Remove the plug

after every 25 hours of operation and check its condition.

1. Stop the engine and allow it to cool. Grasp the plug

wire firmly and pull it from the spark plug.

2. Clean around the spark plug. Remove the spark plug

from the cylinder head by turning a 5/8-inch socket

counterclockwise.

3. Replace a cracked, fouled or dirty spark plug. Set

the air gap at 0.020 in. (0.5 mm) using a feeler gauge

(Fig. 41).

4. Install a correctly-gapped spark plug in the cylinder

head. Tighten by turning the 5/8-inch socket

clockwise until snug.

If using a torque wrench torque to:

110-120 in.•lb. (12.3-13.5 N•m)

Do not over tighten.

0.020 in.

(0.5 mm)

Fig. 41

CAUTION: Do not sand blast, scrape or

clean electrodes. Grit in the engine could

damage the cylinder.

WARNING: The cutting attachment may be

spinning during idle speed adjustments.

Wear protective clothing and observe all

safety instructions to prevent serious

personal injury.

WARNING: To prevent serious personal

injury, make sure the cutting attachment

has stopped rotating before you turn it off

and set it down.

MAINTENANCE AND REPAIR INSTRUCTIONS

CLEANING

Use a small brush to clean off the outside of the unit.

Do not use strong detergents. Household cleaners that

contain aromatic oils such as pine and lemon, and

solvents such as kerosene, can damage plastic housing

or handle. Wipe off any moisture with a soft cloth.

STORAGE

• Never store a fueled unit where fumes may reach an

open flame or spark.

• Allow the engine to cool before storing.

• Store the unit locked up to prevent unauthorized use

or damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

LONG TERM STORAGE

If you plan on storing the unit for an extended time, use

the following storage procedure:

1. Drain all fuel from the fuel tank into a container with

the same 2-cycle fuel mixture. Do not use fuel that

has been stored for more than 60 days. Dispose of

the old fuel/oil mix in accordance to Federal, State

and Local regulations.

2. Start the engine and allow it to run until it stalls. This

ensures that all fuel has been drained from the

carburetor.

3. Allow the engine to cool. Remove the spark plug and

put 1 oz. (30 ml) of any high quality motor oil or

2-cycle oil into the cylinder. Pull the starter rope

slowly to distribute the oil. Reinstall the spark plug.

NOTE: Remove the spark plug and drain all of the oil

from the cylinder before attempting to start the

trimmer after storage.

4. Thoroughly clean the unit and inspect it for any loose

or damaged parts. Repair or replace damaged parts

and tighten loose screws, nuts or bolts. The unit is

ready for storage.

TRANSPORTING

• Allow the engine to cool before transporting.

• Drain fuel from unit.

• Tighten fuel cap before transporting.

• Secure the unit while transporting.

WARNING: To avoid serious personal injury,

always turn your trimmer off and allow it to

cool before you clean or service it.

ACCESSORIES/REPLACEMENT PARTS

2-Cycle Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147543

Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610311

Spark Arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . .182747

Replacement Line . . . . . . . . . . . . . . . . . . . . . . . . 180120

Replacement Line Cartridge . . . . . . . . . . . . . . . . 147345

Inner Reel Spring . . . . . . . . . . . . . . . . . . . . . . . . 610636

Outer Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 683301

Inner Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147495

Bump Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180814

Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180000

Shoulder Strap . . . . . . . . . . . . . . . . . . . . . . . . . . 682075

For specific replacement parts, refer to the parts list

located on the inside back cover of this manual.

La page charge ...

Ryobi Trimmer 790r Manuel utilisateur

Marque: Ryobi

Modèle: Trimmer 790r

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

780r
790r

Télécharger le PDF

rapport

dans d''autres langues

English: Ryobi Trimmer 790r User manual
español: Ryobi Trimmer 790r Manual de usuario

Ryobi Trimmer 790r Manuel utilisateur

Ce manuel convient également à

Ryobi Trimmer 790r Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents