Boston Acoustics TVEE 22 Manuel utilisateur

Catégorie
Équipement musical supplémentaire
Taper
Manuel utilisateur
User Manual
TVee
Model 22
What’s in the Box
TVee Model 22
Power cord
AAA batteries (2)
AAA
AAA
Remote control User Manual
User Manual
TV ee Model 22
Optical Cable
2
Position your sound bar
Place the sound bar centered under the TV
and flush with the front edge of the cabinet.
It is best if you do not install the sound bar
inside of a cabinet.
3
Connect the TV
Note: Optical is the preferred input; however, if the TV does not have an AUX or Optical output,
use an analog cable(not included) to connect the sound bar to the TV.
Optical (Recommended)
1. Insert one end of the optical cable into the
OPTICAL port on the sound bar.
2. Insert the other end of the cable into the
optical port on the TV.
SUB OUTAUXOPTICALUSBAC IN
4
Connect the power
Connect the power cord to the POWER port on the back of the sound bar.
Connect the other end of the power cord into an AC power outlet.
SUB OUT AUX OPTICAL USB AC IN
5
1.
2.
set up the remote
1. Turn the remote to view the back.
2. Open the back cover of the remote by sliding the bottom half downward.
3. Insert the two AAA batteries into the remote and replace the cover.
AAA
AAA
123
6
verify the connections
1. Turn on the TV.
2.
3.
Make sure the sound bar is powered on
(white status light on front).
4.
Verify that you hear sound from the sound
bar by adjusting the volume using the sound
bar remote. If you do not hear sound, refer
to the Tips and Troubleshooting section.
Toggle the mute button on the remote
to verify that the mute command is
operational.
7
remote control features
Power
Turn on or off.
Night Mode
Input
Change the input source.
(Long press for Auto Input Search)
Volume -
decrease volume.
Virtual X
Turns Virtual X on/off.
Mute/unmute.
EQ
Cycle through EQ settings.
Bass +
increase the bass level.
Press to turn mode on/off.
Volume +
Increase volume.
Treble +
increase the treble level.
Bass -
decrease the bass level.Treble -
decrease the treble level.
TruVolume
Turns TruVolume on/off.
Mute
8
sound modes
The TVee Model 22 has been designed to automatically optimize sound for TV, movie and music.
The engineers have also created Equalizer Mode and Night Mode to further enhance your listening
experience and provide a way to further customize your television sound.
Equalizer Mode
Press the EQ button to cycle through equalizer settings: Movie,
Music.
Night Mode
Press the NIGHT button to enable/disable Night Mode. When enabled
(On), the bass level will be lowered on the sound bar. If an external
subwoofer is connected, bass level will also be lowered.
Note: Night mode will be OFF the next time the sound bar is turned on.
Note: Movie mode is on by default.
Night
mode
Equalizer
mode
9
top panel controls
Power: Turns the sound bar on/off.
Input: Selects the TV input connection (AUX or optical)
Bluetooth: Selects the Bluetooth input.
Volume up and down buttons: Control the volume of the sound bar.
Power
On/Off
Volume
Up
Input Bluetooth
Volume
Down
10
Back panel ports
SUB OUT: Used to subwoofer speakers to the sound bar.
AUX: Connects to your TV’s AUX output.
Optical audio in: Connects to your TV’s optical output.
USB: Used for software updates by the factory.
AC IN: Connects to an AC power source.
SUB OUT AUX OPTICAL USB AC IN
11
LED INDICATOR
The LED indicator will behave differently with each function.
Function LED Behavior Description
Input The LED will blink a different color for
each input.
The LED will blink blue when
searching and turn solid once a device
is paired successfully.
Press the INPUT button on the remote to cycle through the available inputs.
Specific inputs will show a different LED color:
When enabled (On), TruVolume provides a consistent and comfortable
volume level for a more enjoyable listening experience.
Press the VRTX button to enable/disable VirtualX. When enabled (On), all
inputs will produce a virtual sound technology that simulates the effect of
having overhead sound. When disabled (Off ), all sources will playback in
stereo.
Press the TVOL button to enable/disable TruVolume.
Press and hold the button on the sound bar. It will be discoverable for 15
minutes. You can now search for the sound bar using your Bluetooth device.
The sound bar will power down if no device is found.
Press and hold the INPUT button on the remote control for 4 seconds to
enable the auto input detect function.
• Analog 3.5mm/ White LED: 1 blink
• Bluetooth/ LED color: Blue
• Optical digital/ White LED: 2 blinks*
• USB/ White LED: 3 blinks
Bluetooth
Pairing Note: Set your Bluetooth device into pairing mode prior to the sound bar.
DTS
TruVolume one Ding toneOn
two Ding toneoff
one Ding toneOn
two Ding toneoff
On/Off
On/Off
Virtual X
Mute If muted, the LED indicator will slowly pulse. Press the Mute button to mute/unmute the sound bar.
*NoteThe LED will be lit pink for 3 seconds when Dolby Digital decoding, then 3 seconds linear fade to dark.
12
Function LED Behavior Description
Equalizer
Mode A high tone one beep indicates Movie
mode, while a low tone one beep
indicates Music mode.
Press the EQ button to toggle between two preset equalizer settings:
Music and Movie.
Press the TREBLE button then press the Volume up/Volume down button
to increase/ decrease the treble level.
Note: Movie mode is on by default.
Treble
Levels
three Ding tone: Max level
one Ding tone: Minimum level
three Ding tone: Max level
one Ding tone: Minimum level Note: Mid level is the default setting.
Bass
Levels
Press the BASS button then press the Volume up/Volume down button to
increase/decrease the bass level.
Press the NIGHT button to enable/disable Night Mode. When enabled
(On), the bass level will be lowered on the sound bar. If an external
subwoofer is connected, bass level will also be lowered.
If a subwoofer is connected, adjusting the bass level will also adjust the
subwoofer level. Consult your subwoofer's user manual for additional
adjustments that may optimize your listening experience.
Note: Mid level is the default setting.
Night Mode
one Ding tone: on
two Ding tone: off Note: Night mode will be OFF the next time the sound bar is turned on.
On/Off
13
Using Button Combinations
There are 3 functions that are triggered by 3
different button combinations on the sound bar.
Function LED Behavior Description
Factory
Reset
Reset the sound bar to the factory default settings.
To perform a Factory Reset, Press and Hold the Bluetooth( ) and Input buttons
for 5 seconds.
Note: This will erase all settings and preferences that you have set.
LED will fl ash 3 times.
one Ding tone: on
two Ding tone: off
Eco Power Mode
Note: Eco Power Mode setting is OFF by default.
When the Eco Power mode setting is enabled, the sound bar will automatically
power down after a period of inactivity. When disabled, the sound bar will
remain powered on until you turn it off .
To enable/disable this function, Press and Hold the Power ( ) and Volume Up
(+) buttons for 5 seconds.
14
using the remote control learning function
If your TV is connected to the sound bar using the optical cable
and you are not able to control the volume of the sound bar with
your TV remote, you can use the Remote Control Learning
function to control volume and mute functions on your sound bar.
IMPORTANT: Hold both remotes about 12” (30 cm) directly in front
of the sound bar when pressing their respective buttons, and make
sure your remotes have fresh batteries.
Entering remote control learning Mode
Make sure your sound bar is powered on, then press and hold the input and Volume up button on the
sound bar for about 5 seconds. When you hear a two-note tone, release the button. You should now
see yellow light breath.
1. Select a button on your Boston sound bar remote.
Press and release the button on the Boston remote that you want to learn (ex: Volume Up).
You will hear a single tone and see yellow light pulsing.
2. Select a button on your TV remote.
Press and release the button on your TV remote that you want to assign to the button you
selected in Step 1.
3. Verify the results.
• If you hear a single tone and see green light, the command was successfully learned.
• If you hear a two-note tone and see red light, the command was not learned.
12” (30 cm)
15
4. Learn another code.
When you see the yellow light breath again, you are ready to select your next function to learn by
repeating steps 1–3.
Exiting remote control learning Mode
Press and hold the Input and Volume up button on the sound bar again for about 5 seconds. When
you hear a two-note tone, release the button.
Note: The sound bar will automatically exit IR learn mode if it has not received any IR commands for
60 seconds. All learned IR commands will automatically be saved.
Clearing learned remote control Codes
Press and hold the Input and Volume up button on the sound bar for about 10 seconds. You will hear
a two-note tone. Continue holding the button and release the button after you hear a three-note
tone.
using the remote control learning function
16
USING BLUETOOTH MODE
Your sound bar supports music streaming from smartphones, tablets, and computers with Bluetooth
capability. Device compatibility will vary, see your device’s documentation for more information.
A Bluetooth signal has a range of up to 30 feet. Keep in mind that Bluetooth is a compressed audio
format, so streamed music may lose some integrity when compared to a wired connection.
Try the following if your sound quality is less than optimal:
• Once you have paired your source device to the sound bar, as long as you stay within range
of the sound bar, your device should remain paired. The Bluetooth name is displayed as
"Boston Acoustics TVee".
• If the input is changed, the Bluetooth device will disconnect.
• If the source is changed back to Bluetooth, any paired Bluetooth device will reconnect
automatically.
• If you hear any break-up or disconnect while streaming music from your device, move the source
device closer to the sound bar.
• Be sure that there are no solid obstructions in the line-of-sight between the sound bar and the
source device.
• Other wireless devices can affect Bluetooth range, including wireless security cameras, wireless
video baby monitors, cordless phones, and microwave ovens. Turning off or moving these devices
may improve Bluetooth range.
Maximizing Signal
Reduce the volume levels on your device and
on the sound bar before pressing Play. High
volume levels can damage your hearing.
WARNING
17
Tips and troubleshooting
There is no power.
• Press the POWER button on the remote control or on the top of your sound bar.
• Ensure the power cord is securely connected.
• Plug a different device into the electrical outlet to verify that the outlet is working correctly.
I don’t hear any sound.
• Increase the volume. Press Volume Up on the remote control or on the top of your sound bar.
• Press MUTE on the remote to ensure the sound bar is not muted.
• Press INPUT on the remote or on the top of your sound bar to select a different input source.
• When using the optical input, if there is no audio: (A) Try setting the TV output to PCM or
(B) Connect directly to your Blu-ray/other source, some TVs do not pass through digital audio.
• On the optical input, the input LEDs will flash rapidly and vocally announce "Format Not Supported"
if an unsupported format is present. Set the source to output PCM.
• Your TV may be set to variable audio output. Confirm that the audio output setting is set to FIXED
or STANDARD, not VARIABLE. Consult your TV’s user manual for more detailed information.
• If using Bluetooth, ensure that the volume on your source device is turned up and that the device
is not muted.
I hear buzzing or humming.
• Ensure all cables and wires are securely connected.
• Connect a different source device (TV, Blu-ray player, etc) to see if the buzzing persists.
If it does not, the problem may be with the original device.
• Connect your device to a different input on the sound bar.
18
Tips and troubleshooting
The remote isn’t working.
• Replace the remote batteries with new ones.
• Point the remote directly at the center of the Sound Bar when pressing a button.
• If using a Bluetooth connection, some of the buttons on the remote may not be supported by
the streaming application. (e.g., Pandora doesn’t support the Back button.)
How do I perform a factory reset?
• Press and hold the Bluetooth and Input buttons at the white light flashes 3 times, then
release the buttons.
• The light will turn off indicating the reset sequence has started.
19
Specifications
*Sound pressure level measured using pink noise at 1 meter, c-weighted.
Sound Bar: 22" x 4.56" x2.28" (558.8 x 116 x 58 mm)
Connections: One 3.5mm AUX
One Optical (Toslink)
Bluetooth
One USB (Supports .WAV and .MP3 format only)
One Subwoofer
Sound Pressure Level* (System):
Frequency Response (System):
90 dB
70 Hz - 20 KHz
Voltage: 100-240VAC, 50/60Hz
Compliances: UL 62368-1, FCC PART15 Class B
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70

Boston Acoustics TVEE 22 Manuel utilisateur

Catégorie
Équipement musical supplémentaire
Taper
Manuel utilisateur