Ring Smart Lighting Bridge App Mode d'emploi
- Taper
- Mode d'emploi
Quick Start
1. Set up and install your Ring Bridge.
2. Open the Ring app.
Then, tap Set Up a Device and follow the in-app instructions.
3. Scan this code.
This identifies your Ring Mailbox Sensor for fast and easy setup.
For additional help, visit:
ring.com/help
Let’s get started.
SAFETY INFORMATION
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE.
BATTERY SAFETY
This product contains alkaline batteries. This device requires batteries for use. Only use new 1.5V alkaline or 1.2 NiMH rechargeable AAA-sized
batteries. Never mix old and new batteries. Keep all of the batteries out of the reach of children. Do not open, disassemble, puncture, cut,
bend, shred or heat the batteries and do not allow metal objects to touch the battery terminals on the remote as they can become hot and
cause burns. Remove all batteries if they are worn out or before storing your Device for an extended period of time. Dispose of all batteries in
accordance with applicable laws and regulations and do not dispose of batteries by throwing them into a fire. If any batteries begin to leak,
take steps to prevent the fluid from coming into direct contact with skin or clothes as the fluid could be corrosive and may be toxic. Remove
the batteries and clean the battery compartment in accordance with the battery manufacturer’s recommendations.
PRODUCT SPECIFICATIONS
Model Number: Ring Mailbox Sensor
Electrical Rating: 3 x AAA-cell batteries
Temperature Rating: -4°F to 122°F (-20°C to 50°C)
RECYCLING YOUR DEVICE PROPERLY
In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle, your device in accordance with
your local laws and regulations.
FCC Compliance: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The party responsible for FCC compliance is: Ring LLC, 1523 26th St, Santa Monica, CA USA, 90404
By purchasing or using the product, you agree to the Terms of Service found at ring.com/terms.
For information on our warranty, theft protection, and Ring Protect Plans, see ring.com/legal.
IMPORTANT PRODUCT INFORMATION
Safety and Compliance Information
Use Responsibly. Read all instructions and safety information before use.
©2020 Ring LLC or its aliates. Ring and all related
marks are trademarks of Ring LLC or its aliates.
QR+FR
I
p
L SHAPE CARD 350G C2S
114
131
IMPORTANT PRODUCT INFORMATION
FOR UNITES STATES CUSTOMERS
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Information on this device is on file with the FCC and can be found by
inputting the device’s FCC ID into the FCC ID Search form available at
https://www.fcc.gov/oet/ea/fccid.
The output power of the radio technology used in the Products is below the
radio frequency exposure limits set by the FCC. Nevertheless, it is advised to
use the product in such a manner that minimizes the potential for human
contact during normal operation. This device should be installed and
operated with at least 20 cm between the radiator and your body.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this
equipment.
FOR CANADIAN CUSTOMERS
Innovation, Science and Economic Development Canada (ISED)
Compliance.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this
equipment.
Information Regarding Exposure to Radio Frequency Energy
This equipment complies with IC RSS-102 RF exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with a minimum distance
of 20 cm between the radiator and your body.
POUR LES CLIENTS CANADIENS
Conformité Innovation Sciences et Développement Économique Canada
(ISDE)
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage .
(2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Renseignements relatifs à l’exposition à l’énergie des radiofréquences
Cet équipement est conforme aux limites d’exposition IC CNR-102 prévues
pour des environnements non contrôlés.
Cet équipement doit être installé et utilisé avec un minimum de 20 cm de
distance entre la source de rayonnement et votre corps.
CAN ICES-3 (B)/NMB-3(B)
-
1
-
2
Ring Smart Lighting Bridge App Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Ring 5B21S8-BEN0 Manuel utilisateur
-
Ring 5D22E2 Mode d'emploi
-
Ring 5F49E9 Manuel utilisateur
-
Ring BHAXN001 Mode d'emploi
-
Ring SF49E9 Mode d'emploi
-
Ring 169MAILBXB Mode d'emploi
-
Ring 169AGBS Mode d'emploi
-
-
-
