Hinkley 903880FMB-NDD Manuel utilisateur

DC

DC MOTOR

CEILING FAN INSTRUCTION MANUAL

DAMP

INDOOR/OUTDOOR FAN

80"SWELL™

SO WE’RE HERE IF YOU HAVE A QUESTION, NEED SOME

HELP OR WANT TO CHAT ABOUT OUR PRODUCTS. SEND

SUGGESTIONS OUR WAY TOO—WE’RE ALWAYS LOOKING TO

MAKE YOUR EXPERIENCE WITH HINKLEY A POSITIVE ONE.

This manual contains complete instructions for the

installation and operation of this fan. It has been

designed to make the installation process as easy as

possible. If you are unfamiliar or uncomfortable with

wiring, please contact a qualiﬁed electrician. If you

need additional assistance or have any questions,

please reach out to us.

For warranty information, visit hinkley.com.

> SERVICE@HINKLEY.COM

> 800.HINKLEY

> LET’S SEE THAT HINKLEY STYLE @HINKLEY

#HINKLEYSTYLE

WARNING:

Read and follow these instructions carefully and be mindful of all warnings shown throughout.

TABLE OF CONTENTS

02 GENERAL INSTALLATION & OPERATING

INSTRUCTIONS

03 IMPORTANT SAFETY PRECAUTIONS

03 TOOLS & MATERIALS REQUIRED

04 UNPACKING YOUR FAN

05 PREPARATION

05 INSTALLING THE HANGING BRACKET

06 HANGING THE FAN

08 ELECTRICAL CONNECTIONS

09 FINISHING THE INSTALLATION

10 BLADE ATTACHMENT

11

12

INSTALLING THE WALL CONTROL

14

OPERATION

14

CARE AND CLEANING

15

TROUBLESHOOTING

15

ENERGY GUIDE

15

SPECIFICATIONS

SMART BY BOND

NOTE: Limit one fan per power circuit.

GENERAL INSTALLATION & OPERATION INSTRUCTIONS

1

2

3

4

5

6

7

8

9

10

02 | hinkley.com

To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning.

To avoid possible electric shock, be sure electricity is turned o at the main power box before wiring. All electrical connections must be made in

accordance with local codes, ordinances and/or the National Electric Code. If you are unfamiliar with the methods of installing electrical wiring

and products, secure the services of a qualied and licensed electrician as well as someone who can check the strength of the supportive ceiling

members and make the proper installation(s) and connections.

WARNING: To reduce the risk of re, electric shock, or other personal injury, mount fan only on an outlet box or supporting system marked

acceptable for fan support of 35 lbs (15.9 kg) or less and use mounting screws provided with the outlet box. Most outlet boxes commonly used

for the support of lighting xtures are not acceptable for fan support and may need to be replaced. Consult a qualied electrician if in doubt.

Make sure that your installation site will not allow rotating fan blades to come in contact with any object. Blades should be at least 7 feet from

oor.

Blades should be attached after motor housing is hung and in place. Fan motor housing should be kept in the carton until ready to be installed

to protect its nish. If you are installing more than one ceiling fan, make sure that you do not mix fan blade sets, as each blade is part of a

weighted set.

After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be

spread apart with the common conductor and the grounding conductor on one side of the outlet box, and the "HOT" wires on the other side.

Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed and should be installed per the light kit's

installation instructions.

After fan is completely installed, check to make sure that all connections are secure to prevent fan from falling and/or causing damage or injury.

The fan can be made to work immediately after installation - the bearings are adequately charged with grease so that, under normal conditions,

further lubrication should not be necessary for the life of the fan.

To operate the reverse function on this fan, press the reverse button while the fan is running.

NOTE: Limit one fan per power circuit.

IMPORTANT SAFETY PRECAUTIONS

TOOLS & MATERIALS REQUIRED

WARNINGS:

• PHILLIPS SCREWDRIVER

• FLAT SCREWDRIVER

• WRENCH OR PLIERS

• WIRE CUTTER

• STEPLADDER

• WIRING SUPPLIES AS REQUIRED BY

ELECTRICAL CODE

• Disconnect power by removing fuse or turning o circuit breaker before installing the fan and/or optional lighting.

• Support directly from building structure.

• To reduce the risk of re, electric shock or personal injury, mount to outlet box marked "acceptable for fan support" and use mounting

screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting xtures are not acceptable for fan

support and may need to be replaced. Consult a qualied electrician if in doubt.

• Do not use an incandescent light dimmer. Do not use this fan with any transformer type fan speed control device.

• To reduce the risk of personal injury, do not bend the blade arms when installing them, balancing the blades or cleaning the fan.

Do not insert any object(s) between rotating fan blades.

NOTE:

The important precautions, safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations

that may occur. It must be understood that common sense, caution and carefulness are factors which cannot be built into this product. These

factors must be supplied by the person(s) installing, caring for and operating the unit.

OFF ON

I

IIIII IVV

VI

UNPACKING YOUR FAN

UNPACK YOUR FAN AND CHECK THE CONTENTS.

04 | hinkley.com

HOVER PACKAGE CONTENT

1Blade Set of 3 BL903880FMB (Walnut)

BL903880FGT

CA903860FMB

CA903860FGT

YC903860FMB

YC903860FGT

DR94016FMB

DR94016FGT

MH903860FMB

MH903860FGT

980013FAS

CN903880

(Driftwood )

2Hanging Bracket

3Ceiling Canopy and Trim Ring

4

5

6

8

7

9

10

1

10

2

5

3

8

9

• Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing.

Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged.

• Examine all parts. You should have the following:

NOTE: Design of parts shown above may look slightly dierent for

your specic model of fan.

4

Downrod Asm.

Yoke Cover

Receiver .

Wall Control w/12v Battery

Wall Plate, Face Plate,

2 Sets of Mounting Screws,

and Machine Screws

Hardware Bag

Fan Housing with Motor

*Remove rubber shipping

supports around motor, if

applicable. Save the screws.

Blade to Motor Screws and

Lock Washers and Flat Washers.

Safety cable hardware

(wood screw, at washer)

Bracket Mounting Hardware

(wood screws, screws, lock

washers, star washers, at washers)

5 Wire Nuts

Balance Kit

Blades Ring

6

7

PREPARATION

INSTALLING THE HANGING BRACKET

PREPARATION:

Parts identiﬁcation on assembled fan.

Ceiling Fan

Outlet Box

Hanger

Bracket

Outlet Box

Screw

Flat Washer

Spring Washer

Fig. 1

Verify you have all parts before beginning the

installation. Check foam insert closely for missing

parts. Remove motor from packing. To avoid

damage to nish, assemble motor on soft padded

surface or use the original foam inset in motor

box.

DO NOT LAY MOTOR HOUSING ON ITS SIDE AS

THIS COULD RESULT IN SHIFTING OF

MOTOR IN DECORATIVE ENCLOSURE.

CAUTION: To avoid possible electrical shock, be sure electricity is turned o at the main

power box before wiring. All wiring must be in accordance with National and Local

Electrical Codes and the ceiling fan must be grounded as a precaution against possible

electric shock.

Blade

Yoke Cover

Downrod

Canopy

Motor Housing

1

2

3

4

Locate ceiling joist where fan is to be mounted, being sure location agrees with

the requirements in the minimum clearance section of this guide. Wood joists

must be sound and of adequate size to support 35 pounds (See page 2, items 3

and 4).

If not already present, mount a UL listed outlet box marked "suitable for fan

support" following the instructions provided with the outlet box. The outlet box

must be able to support a minimum of 35 pounds.

Remove canopy from hanger bracket. Remove twist-lock trim ring by rotaing

counter-clockwise. Remove canopy screw that does not have

key slot in canopy. Loosen screw with key slot and remove canopy.

Attach hanging bracket to outlet box using screws provided with the outlet box.

HANGING THE FAN

1

2

3

4

5

06 | hinkley.com

Fig. 1

Fig. 2

Downrod

Cross pin

Hanger

ball Set screw

Downrod

Mounting Collar

Downrod Pin

Security Screws

Cotter Pin

Top of

Fan Body

Remove ball from downrod by loosening set screw in the side of the

ball. Slide ball down and remove ball pin; remove ball. (Fig. 1)

Carefully support fan body (motor) in its styrofoam packing with the

mounting collar (where the wires come out) facing upward.

Loosen the two security set screws and remove the downrod pin

and retaining clip from the coupling on top of the motor assembly.

(Fig. 2)

Carefully feed the electrical lead wires and safety cable from the fan

through the downrod. Thread downrod into coupler until holes

align. Insert downrod pin through holes in mounting collar and

downrod; clip cotter pin through small hole in end of downrod pin

to hold downrod in place.

Tighten security set screws against downrod using a large at blade

screwdriver to ensure a tight t against downrod. Tighten nuts

against mounting collar.

Blades Ring

07

Fig. 3

Ground Wire

Top of

Fan Body

Yoke Cover

Downrod

Canopy

Hanger ball

Set screw

Cross Pin

REMEMBER to turn o the power before you begin.

To properly install your ceiling fan, follow the steps below.

Slip the blades ring, yoke cover, trim ring and canopy onto the downrod.

(Fig. 3)

Slide the hanger ball onto the downrod, insert the cross pin through the

downrod and tighten. Tighten the set screw.

Feed wires through holes in rubber ball moisture cap and slide cap down

over top of ball. (Fig. 3)

Lift ball/downrod/fan into hanger bracket opening.

NOTE: The tab opposite hanger bracket opening should t in slot on ball.

(Fig. 4)

6

7

8

9

NOTE:

6 feet of lead wire is supplied on the fan for use with

longer downrods.

Trim Ring

Fig. 4

Attach the wood screw and the ﬂat washer to the ceiling joist as

shown (do not fully tighten). Slide the cable clamp onto the

safety cable from the fan. Loop the safety cable around the

wood screw that was just attached to ceiling joist. Feed the end

of the cable into the clamp and pull as much cable through as

possible. Firmly tighten screw in the clamp. Cut o excess cable.

INSTALLATION OF SAFETY CABLE SUPPORT

Safety Cable Clamp

Safety Cable

Wood Ceiling Joist

Safety Cable Loop

Wood Screw

And Washer

ELECTRICAL CONNECTIONS

08 hinkley.com

REMEMBER -Turn o the power! NOTE - Control must be installed within 30 feet of fan.

Use the wire nuts supplied with your fan when making connections. Secure the connectors with electrical tape and make sure there are no loose connections or wire

strands.

Insert the receiver into the ceiling mounting bracket with the at side of the

receiver facing the ceiling. (Fig. 1) For best performance, make sure the Black

Antenna, on the end of the receiver, remains extended and not tangled with

any of the electrical wires.

Make wire connections from the fan to the receiver unit. For this

step use the bundle of 5 wires on the receiver. (Fig. 2)

Connect the YELLOW fan wire to the YELLOW receiver wire.

Connect the GRAY fan wire to the GRAY receiver wire.

Connect the RED fan neutral wire to the RED receiver neutral wire.

Connect the WHITE fan neutral wire to the WHITE receiver neutral wire.

Connect the BLUE fan neutral wire to the BLUE receiver neutral wire.

Connect the wiring from the ceiling to the receiver unit. (Use the 2 wire

bundle on the receiver.) Secure with supplied wire nuts.

Connect the BLACK building supply wire to the BLACK receiver wire.

Connect the WHITE receiver neutral wire to the WHITE building neutral

wire.

Connect the COPPER building ground wire to the YELLOW/GREEN fan

ground wire. Also connect the two GREEN wires (from fan) to building

ground wire.

|

Fig. 2

Fig. 1

Receiver

Hanger

bracket

Receiver

Fan

Outlet box

Ceiling

WH (AC IN)

GRN

GROUND

GRN (downrod)

GRN (hanger bracket)

WH

BLK

BLK (AC IN)

YELLOW/GRN

ORANGE (to motor)

GRAY (to motor)

YELLOW (to motor)

ORANGE (motor)

GRAY (motor)

YELLOW (motor)

1

2

3

NOTE: One fan per power circuit.

FINISHING THE INSTALLATION

1

2

3

4

2

1Tuck connections neatly into ceiling outlet box.

Slide the canopy up to mounting bracket and allign the key

hole on the canopy to the screw on the mounting bracket,

turn canopy until it locks in place at the narrow section of the

key holes.

Align the circular hole on canopy with the remaining

hole on the mounting bracket, secure by tightening the

two set screws.

Assemble trim ring by aligning slots in trim ring with canopy

screw heads.Twist to lock into place.

NOTE: Adjust the canopy screws as necessary until the canopy

and trim ring are snug.

Canopy

Screws

Trim Ring

Ceiling Fan

Outlet Box

Hanger

Bracket Groove

WARNING:

Make sure the hook on the hanging bracket properly sits in the groove in the hanger ball before

attaching the canopy to the bracket by turning the housing until it drops into place.

Blades Ring

BLADE ATTACHMENT

NOTE:

Fasten blade to motor with provided screws, lock washers and at

washers. Repeat procedure for remaining blades. Make sure screws are

TIGHT! Loose motor screws can contribute to unnecessary hum during

operation.

Cordless power screwdrivers are NOT recommended,

as they usually strip the heads of the screws and

usually will not fully compress the lock washers on

the motor screws. Use a large at blade screwdriver

for nal tightening to fully compress the washers. This

will help ensure proper alignment of the blades and

noise-free, wobble-free running.

10 | hinkley.com

NOTE:Remove any rubber supports that are installed for

shipping.

1

2

4

3

Locate 9 blade attachment screws. Slide one

blade onto the motor as shown in Fig.2,

aligning holes in blade with holes on the

edge of the motor.

First install a short screw to the hole in the middle

of the blade, repeat for all three blades.

Place blade ring on the blade, aligning all holes

in blade with all holes on blade ring, install 2 blade

attachment screws.

Make sure to completely tighten completely each screw .

Tighten all screws securely.

Yoke Cover

Downrod

Canopy

Trim Ring

Fig.1

Fig.2

Downrod

Yoke Cover

INSTALLING THE WALL CONTROL

Fig. 2

Wall plate

Switch

Outlet box

Fig. 1

REMEMBER to turn o the power before you begin.

NOTE - Control must be installed within 30 feet of fan.

Remove the existing wall plate and the old switch from the

wall outlet box. (Fig. 1)

Connect the wiring from the wall switch receptacle to wall

transmitter unit

Connect one BLACK wire from the wall to one BLACK wire

(labeled "TO FAN") from the wall transmitter.

Connect the other BLACK wire (labeled "TO POWER

SUPPLY") from the transmitter to the remaining BLACK wire

from the wall (A/C supply source).

Connect the green ground wire form the switch to the ground

wire on the wall outlet box.

Install the wall transmitter on the existing wall outlet box using

the screws provided. Attached the wall plate with the

mounting screws to nish the installation. (Fig. 2)

TransmitterDecorative Wall Plate

1

2

4

3

12 | hinkley.com

OPERATION

1

2

3

4

Your DC brushless motor is equipped with an

automatically learned type remote control. There is

no frequency switches on the receiver or

transmitter. The fan can start to use once the

pairing process is done.

Remove the panel from the transmitter and then

install one 23A/12V battery (included). To prevent

damage to transmitter, remove the battery if not

use for long periods of time (Fig. 16).

I, II, III, IV, V and VI button:

These six buttons are used to set the

fan speed as follows:

I = minimum speed

II = low speed

III = medium low speed

IV = medium speed

V = medium high speed

VI = high speed

button:

This button turns the fan o.

Reverse button:

This button is to control fan direction.

This button must be pressed while fan is

running (suggested speed IV)

Light button:

This button is to control optional light.

Switch the "D" and "ON" dip switch on the

front of transmitter to decide the light in

"ON/OFF" or "Dimmable" condition.

"SET" code setting button:

Follow the below steps to use the set

button. (Fig. 1)

ON - OFF Slide button: Power switch.

(Fig. 16)

Signal light (Fig. 2)

Pairing Process

With the fan’s power o, restore power to the fan.

Press and hold “SET” button for about 5 seconds

and release. If optional light kit is installed, the light

kit will ash twice and the signal light on the wall

control will come on when the button is pressed.

The fan has completed the pairing process with the

wall control and is ready for use.

NOTE: A single fan can be controlled with as many

as 3 wall controls in one room. Every control will

need to repeat the pairing process based on

instructions above and all controls must be within

30 feet of the fan.

Power switch

Signal light

Fig. 1

Fig. 2

1

2

3

4

5

6

7

Fig. 3 Fig. 4

SUMMER MODE

(COUNTERCLOCKWISE DIRECTION)

WINTER MODE

(CLOCKWISE DIRECTION)

8

9

Summer Mode and Winter Mode Operation

Summer Mode (forward):

A DOWNWARD airow creates a cooling eect as shown in Figure 3. This allows you to set your air conditioner on a warmer setting without

aecting your comfort.

Winter Mode (Reverse):

An UPWARD airow moves warmer air o the ceiling area as shown in Figure 4. This allows you to set your heating unit on a cooler setting without

aecting your comfort.

14 | hinkley.com

CARE AND CLEANING

Periodically it may be necessary to re-tighten blade to blade arm screws or blade arm to motor screws to prevent clicking or humming sound during operation. This is

especially true in climates with broad temperature and humidity ranges.

When dusting the blades, you must support the blade to prevent bending - no pressure should be applied to the blades. If you experience any aws in the operation of

your fan, please check the following points.

TROUBLESHOOTING

PROBLEM SOLUTION

FAN WILL

NOT START

FAN SOUNDS

NOISY

FAN WOBBLES

1. Check circuit fuses or breakers.

2. Check wall control LED indicator light. If LED is not illuminated when pushing a button, it is not transmitting a

signal. Please check power to wall control/circuit breaker and all electrical connections.

3. Assure there are no more than 2 fans operating on a circuit through the wall control. Assure that there are no

more than 12 fans operating on a circuit through an on/o wall switch or a breaker (not through a wall control).

4. Assure that the fan in within range of the WiFi (150 ft.) or wall control (30 ft.).

5. Check to assure only one fan is installed in the power circuit.

1. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan will disappear during this time.

2. Make sure all motor housing screws are securely fastened.

3. Make sure the screws that attach the fan blade to the fan are tight.

4. Make sure your ceiling box is secure and rubber isolator pads are used between the mounting bracket and outlet

box.

1. Check that all blade and blade arm screws are secure.

2. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight

and possibly result in smoother operation.

3. Check to assure all dowrods to motor hardware and/or hanger ball are tight.

4. Make sure ceiling box is secure.

CAUTION:

Switch o power supply before carrying out any of these checks.

SPECIFICATIONS

SMART BY BOND

PERFORMANCE

SPECIFICATIONS

STANDARD

HIGH SPEED LOW SPEED

Airﬂow (CFM)

Energy Use (Watts)

Airﬂow Eciency (CFM/W)

Energy Costs (Yearly)

Amps

RPMs

HINKLEY SMART FAN OPTIONS (SOLD SEPARATELY):

https://bondhome.io/app

In addition to the included wall control, you can control your Hinkley fan

through the Bond app using the smart technology accessory controls

SOLD SEPARATELY.

• To use the app, download it for free from the App Store or Google Play.

• Open the app to create your account. You can also login with your Facebook or

Google account.

• Next, set up a WiFi connection. You will need the SSID and WiFi password for

the network you want to connect to.

• You will receive a prompt to choose the ﬁnish of your fan and name your fan

device.

• The app will walk you through the main screen and show you how to change

fan speeds, dim the light, set timers or utilize breeze mode.

NOTE: Maximum of 2 fans can operate on a circuit through the wall control.

Maximum of 12 fans can operate on a circuit through an on/o switch or breaker

when utilizing the app for the fan control (without the wall control in the circuit).

ENERGY GUIDE

AVERAGE PERFORMANCE AND ENERGY INFORMATION

$

3

68,554

20

39.7

276

11

0.50

102

10955 10955 5832

10.9

535

3

0.09

46

HINKLEY IS PROUD TO PROVIDE YOU WITH CEILING FAN

PRODUCTS THAT ENHANCE YOUR SPACE WITH COMFORT,

PURPOSE AND STYLE. AS A FAMILY COMPANY, WE ARE

COMMITTED TO DESIGN, PERFORMANCE AND QUALITY,

AND WHAT’S IMPORTANT TO YOU IS PARAMOUNT TO US.

GLOBAL HEADQUARTERS

33000 Pin Oak Parkway | Avon Lake, Ohio 44012

T (440) 653 5500 | F (440) 653 5555 | hinkley.com

DC

DC MOTOR

MANUAL DE INSTRUCCIONES PARA VENTILADORES DE TECHO

DAMP

VENTILADOR INTERIOR / EXTERIOR

80"SWELL™

La page charge ...

Hinkley 903880FMB-NDD Manuel utilisateur

Ce manuel convient également à

Hinkley 903880FMB-NDD Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents