Pioneer Car Amplifier PRS-D1100M Manuel utilisateur

Marque: Pioneer

Modèle: Car Amplifier PRS-D1100M

Catégorie: Amplificateurs audio

Taper: Manuel utilisateur

Ce manuel convient également à

ENGLISH

FRANÇAIS

ESPAÑOL

ITALIANO

NEDERLANDS

êìëëäàâ

CLASS D MONO AMPLIFIER

AMPLIFICATEUR MONO DE CLASSE D

Owner’s Manual

PRS-D1100M

Mode d’emploi

1
Before Using This Product  ...................... 1
Information to User  .......................................... 1
Important .......................................................... 1
Visit our website ................................................ 2
About This Product ............................................ 2
CAUTION ........................................................ 2
WARNING ........................................................2
Setting the Unit  .......................................... 3
Terminal Cover  ................................................ 3
Power Indicator  ................................................ 3
Subsonic Select Switch  .................................... 3
Bass Boost Control ............................................ 3
BFC (Beat Frequency Control) Switch  ............ 3
MODE SELECT Switch   .................................. 4
Gain Control ...................................................... 4
Cut Off Frequency Control for LPF .................. 4
Input Switch  ...................................................... 4
POWER MODE Switch .................................... 4
Connecting the Unit  .................................. 5
Connection Diagram  ........................................ 6
Connecting the Power Terminal ........................ 7
Connecting the Speaker Output Terminals  ...... 8
Using the Speaker Input  .................................... 8
Connecting the Speaker Wires  .......................... 9
Installation ................................................ 13
Example of installation on the floor mat 
or on the chassis  ...................................... 14
Replacing the terminal cover  .......................... 14
Specifications .......................................... 15
Thank you for purchasing this PIONEER
product. It is designed to give you many
years of enjoyment.
PIONEER SUGGESTS USING A PRO-
FESSIONAL INSTALLER DUE TO THE
COMPLEXITY OF THIS PRODUCT.
Please read all instructions and WARN-
INGS in this manual before attempting
operation. Should you have any questions,
contact your nearest Pioneer authorized
dealer or installation specialist.
Information to User
Alteration or modifications carried out
without appropriate authorization may
invalidate the user’s right to operate the
equipment.
Important
The serial number of this amplifier is writ-
ten on the bottom of the unit. For your 
own security and convenience, write it
down on the enclosed warranty card. Keep
the card handy for future reference.
Contents Before Using This Product
After-sales service for Pioneer
products
Please contact the dealer or distributor from where
you purchased the product for its after-sales ser-
vice (including warranty conditions) or any other
information. In case the necessary information is
not available, please contact the companies listed
below:
Please do not ship your product to the companies
at the addresses listed below for repair without
advance contact.
7 U.S.A.
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
7 CANADA
Pioneer Electronics of Canada, Inc.
CUSTOMER SATISFACTION
DEPARTMENT
300 Allstate Parkway
Markham, Ontario L3R OP2
1-877-283-5901
For warranty information please see the Limited
Warranty sheet included with your product.

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

Visit our website

Visit us at the following site:

1 Register your product. We will keep the details of

your purchase on file to help you refer to this

information in the event of an insurance claim

such as loss or theft.

2 Receive updates on the latest products and tech-

nologies.

3 Download owner’s manuals, order product cata-

logues, research new products, and much more.

About This Product

This product is a class D amplifier for the

subwoofer. If both L (left) and R (right)

channels are connected to the RCA input

of this product, output is mixed because

this product is a mono amplifier.

CAUTION

Never replace the fuse with one of greater

value or rating than the original fuse. Use of

an improper fuse could result in overheating

and smoke and could cause damage to the

product and injury including burns.

WARNING

• Handling the cord on this product or cords associat-

ed with accessories sold with the product will

expose you to lead, a chemical known to the State

of California and other governmental entities to

cause cancer and birth defects or other reproductive

harm. Wash hands after handling.

• Always use the special red battery and ground

wire [RD-223] and [RD-222], which are sold sep-

arately. Connect the battery wire directly to the

car battery positive terminal (+) and the ground

wire to the car body. There is the risk of a fuse

burning out if only one of these is connected.

• Do not touch the amplifier with wet hands.

Otherwise you may get an electric shock. Also, do

not touch the amplifier when it is wet.

• For traffic safety and to maintain safe driving

conditions, keep the volume low enough so that

you can still hear normal traffic sound.

• Check the connections of the power supply and

speakers if the fuse of the separately sold battery

wire or the amplifier fuse blows. Detect the cause

and solve the problem, then replace the fuse with

another one of the same size and rating.

• To prevent malfunction of the amplifier and speak-

ers, the protective circuit will cut the power supply

to the amplifier (sound will stop) when an abnor-

mal condition occurs. In such a case, switch the

power to the system OFF and check the

connection of the power supply and speakers.

Detect the cause and solve the problem.

• Contact the dealer if you cannot detect the cause.

• To prevent an electric shock or short-circuit

during connection and installation, be sure to

disconnect the negative (–) terminal of the battery

beforehand.

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier. Be

sure to protect all cables and important equipment

such as fuel lines, brake lines and the electrical

wiring from damage.

• DO NOT allow amplifier to come into contact with

liquids due to, for example, the location where the

amplifier is installed. Electrical shock could result.

Also, amplifier and speaker damage, smoke, and

overheating could result from contact with liquids.

In addition, the amplifier surface and the surface of

any attached speakers could become hot to the

touch and minor burns could result.

Setting the Unit

Power Indicator

The power indicator

lights when the power

is switched on.

Terminal Cover

Before setting up the unit, unfasten the

screws with a 4 mm hexagonal wrench

and remove the terminal cover.

Bass Boost Control

You can select a bass boost level from

0, 6, 9 and 12 dB.

For instruction of connecting the bass

boost remote control to the amplifier,

see the “Connection Diagram” section.

BFC (Beat Frequency Control)

Switch

BFC switch is on the bottom of the unit.

If you hear a beat while listening to an

AM broadcast with your car stereo,

change the BFC switch using a small

standard tip screwdriver.

Subsonic Select Switch

The subsonic filter cuts inaudible

frequencies below 20 Hz to eliminate

unwanted vibrations and minimize

power loss.

• To adjust the switch, use standard tip screwdriver if needed.

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

Gain Control

If the sound level is too low, even when the volume of the car stereo used along with this

power amplifier is turned up, turn gain control clockwise. If the sound distorts when the vol-

ume is turned up, turn the gain control counter-clockwise.

• When using with an RCA equipped car stereo (standard output of 500 mV), set to the NORMAL

position. When using with an RCA equipped Pioneer car stereo with max. output of 4 V or more,

adjust level to match the car stereo output level.

• If you hear too much noise when using the speaker input terminals, turn the gain control

counter-clockwise.

Input Switch

It is possible to input from a car stereo external output or a car stereo speaker output. Switch

the input switch before turning on the power. Since switching the input switch while the

power is on can cause a loud noise to be emitted from the speakers, the power is turned off

by a protection function. When using an external output, slide the switch to the left. For

connection instructions, see the “Connection Diagram” section. When using a speaker out-

put, slide the switch to the right. In this case, it is necessary to use the supplied speaker input

wire with RCA pin cord. For details, see the “Using the Speaker Input” section.

MODE SELECT Switch

You can select amplifier’s sync mode from MASTER, SYNC and SYNC INV. Set the

MODE SELECT switch to the MASTER position when using one amplifier only. When

using synchronously connecting two or more of these amplifiers in combination, set the first

amplifier to MASTER, and set the remaining amplifiers to SYNC or SYNC INV according

to the manner in which they are connected. The only time the amplifier is switched to the

SYNC INV mode is when amplifiers are synchronously connected with the ex. bridge.

When switching to the SYNC INV mode, the seal over the MODE SELECT switch must be

peeled off and you can find SYNC INV switch. Peel off the seal after checking that connec-

tions are correct. See the “Connecting the Speaker Wires” section for details on the MODE

SELECT switch.

POWER MODE Switch

When using speakers with synthetic impeadance 2

Ω

to 8

Ω

, slide the switch to the right

(NORMAL). When using speakers with synthetic impeadance from 1

Ω

to less than 2

Ω

slide the switch to the left (HI-CURRENT). These settings are only used when using a sin-

gle amplifier. See the “Connecting the Speaker Wires” section when combining the use of

multiple amplifiers.

If the speaker impedance exceeds 2

Ω

when using ex. bridge), although the POWER

MODE switch be may set to the HI-CURRENT position, setting to the NORMAL position

makes it possible to enjoy high power sound.

Cut Off Frequency Control for LPF

You can select a cut off frequency from 40 Hz to 240 Hz.

Connecting the Unit

CAUTION:

To prevent damage and/or injury

• Do not ground the speaker wire directly or con-

nect a negative (–) lead wire for several speakers.

• This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre-

ational vehicle, truck or bus, check the battery

voltage.

• If the car stereo is kept on for a long time while

the engine is at rest or idling, the battery may go

dead. Turn the car stereo off when the engine is at

rest or idling.

• If the system remote control wire of the amplifier

is connected to the power terminal through the

ignition switch (12 V DC), the amplifier will

always be on when the ignition is on— regardless

of whether the car stereo is on or off. Because of

this, the battery could go dead if the engine is at

rest or idling.

• DO NOT connect a subwoofer with a lower

impedance than specified in the “Connecting the

Unit” section. Amplifier damage, smoke, and

overheating could result from a non-specified

connection. The amplifier surface could also

become hot to the touch and minor burns could

result.

• Connect either of three subwoofers to the amplifi-

er; 1: a subwoofer with a 420 W or larger nomi-

nal input and an impedance 4 Ω, 2: a subwoofer

with a 600 W or larger nominal input and an

impedance 2 Ω or 3: a subwoofer with a 600 W

or larger nominal input and an impedance 1 Ω. If

the nominal input and impedance are out of the

above ranges, the subwoofer may catch fire, emit

smoke or become damaged.

• Install and route the separately sold battery wire

as far away as possible from the speaker wires.

Install and route the separately sold battery wire,

ground wire, speaker wires and the amplifier as

far away as possible from the antenna, antenna

cable and tuner.

• Cords for this product and those for other prod-

ucts may be different colors even if they have the

same function. When connecting this product to

another product, refer to the supplied manuals of

both products and connect cords that have the

same function.

CAUTION

• Disconnect the negative (–) terminal of the bat-

tery to avoid the risk of short-circuit and damage

to the unit.

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around it where they lie against metal parts.

• Do not route wires where they will get hot, for

example where the heater will blow over them. If

the insulation heats up, it may become damaged,

resulting in a short-circuit through the vehicle

body.

• Make sure that wires will not interfere with mov-

ing parts of the vehicle, such as the gearshift,

handbrake or seat sliding mechanism.

• Do not shorten any wires. Otherwise the protec-

tion circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply wire to tap

from the wire. The current capacity of the wire

will be exceeded, causing overheating.

• Never replace the fuse with one of greater value

or rating than the original fuse. Use of an improp-

er fuse could result in overheating and smoke and

could cause damage to the product and injury

including burns.

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

Connection Diagram

• This diagram shows connections using external output. Slide the input switch to the left.

• In the case of connecting the external output from a car stereo to an RCA input, use the jack used for full-

range output. This is because the LPF of the amplifier cannot be turned OFF. If this jack cannot be used,

connect the subwoofer output jack to the RCA input.

• When you connect with speaker output, connections defers from the diagram. For details, see the “Using

the Speaker Input” section. In either case, you need to set the input switch. For details, see the “Setting the

Unit” section.

• Always use the special red battery and ground wire ([RD-223] and [RD-222]), which are sold separately.

Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to the car

body. There is the risk of a fuse burning out if only one of these is connected.

Fuse (40 A)

Car stereo with

RCA output jacks

External Output

Connecting wire with RCA

pin plugs (sold separately).

RCA input jack

System remote control wire (sold separately)

Connect the male terminal of this wire to the system remote control terminal of the car

stereo (SYSTEM REMOTE CONTROL). The female terminal can be connected to the

auto-antenna relay control terminal. If the car stereo does not have a system remote control

terminal, connect the male terminal to the power terminal through the ignition switch.

Speaker output terminal

See the “Connecting the

Speaker Wires” section for

speaker connection instruc-

tions.

Bass Boost Remote

Control Wire

Bass Boost

Remote Control

6 m (19 feet 8 inch)

Jack for the bass boost

remote control

Connect this jack and

the bass boost remote

control with the bass

boost remote control

wire.

SYNC OUTPUT/SYNC INPUT jack

See the “Connecting the Speaker Wires”

section for SYNC OUTPUT/SYNC

INPUT jack connection instructions.

Fuse (30 A) × 3

Grommet

Special red battery wire

After making all other connections at the amplifier,

connect the battery wire terminal of the amplifier to

the positive (+) terminal of the battery.

Ground wire (black)

Connect to metal body or chassis.

[RD-223]

(sold separately)

[RD-222] (sold separately)

Connecting the Unit

Connecting the Power Terminal

• Always use the special red battery and ground

wire ([RD-223] and [RD-222]), which are sold

separately. Connect the battery wire directly to

the car battery positive terminal (+) and the

ground wire to the car body. There is the risk of a

fuse burning out if only one of these is connected.

1. Pass the battery wire from the

engine compartment to the interior

of the vehicle.

• After making all other connections to the

amplifier, connect the battery wire terminal

of the amplifier to the positive (+) terminal of

the battery.

[RD-223]

[RD-222]

2. Twist the battery wire, ground wire

and system remote control wire.

3. Attach lugs to wire ends. Lugs not

supplied.

• Use pliers, etc., to crimp lugs to wires.

4. Connect the wires to the terminal.

• Fix the wires securely with the terminal

screws.

WARNING

Failure to securely fasten the battery wire to the ter-

minal using the terminal screws could cause the ter-

minal area to overheat and could result in damage

and injury including minor burns.

GND terminal

Power terminal

Battery wire

System remote

control terminal

System remote

control wire

Ground wire

Twist

Battery wire

Ground wire

Lug

Fuse (30 A)

Engine

compart-

ment

Interior of

the vehicle

Drill a 14 mm

(1/2 inch) hole

into the vehicle

body.

Insert the O-ring rubber

grommet into the vehicle

body.

Positive terminal

Fuse (30 A)

Engine

compart-

ment

Interior of

the vehicle

Drill an 8 mm

(3/8 inch) hole

into the vehicle

body.

Insert the O-ring rubber

grommet into the vehicle

body.

Positive terminal

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

Connecting the Speaker Output

Terminals

1. Expose the end of the speaker wires

using nippers or a cutter by about

10 mm (3/8 inch) and twist.

2. Attach lugs to speaker wire ends.

Lugs not supplied.

• Use pliers, etc., to crimp lugs to wires.

3. Connect the speaker wires to the

speaker output terminals.

• Fix the speaker wires securely with the termi-

nal screws.

Using the Speaker Input

Connect the car stereo speaker output

wires to the amplifier using the supplied

speaker input wire with RCA pin cord.

• Slide the input switch to the right.

7 Connections when using the speaker

input

• As a result of connecting the car stereo speaker

output wire to the amplifier, the power of the

amplifier is turned on automatically when the car

stereo is turned on. It is not necessary to connect

the system remote control wire in this case.

• In the case the amplifier and head unit are con-

nected using a speaker input wire with RCA pin

cord, the amplifier power is only turned on when

one amplifier is being used. If two or more ampli-

fiers are synchronously connected in combina-

tion, connect the head unit and all of the ampli-

fiers with the system remote control wire.

Note:

• Connect the system remote control wire when the

power of the amplifier is not to be turned on

when the car stereo is turned on.

10 mm

(3/8 inch)

Twist

Speaker wire

Lug

Speaker

output

terminal

Terminal screw

Speaker wire

Speaker

output

Car Stereo

Speaker input

wire with RCA

pin cord

To RCA input

jack of this unit.

White: Black: Black: Red:

Left + Left ≠ Right ≠ Right +

Connecting the Unit

Connecting the Speaker Wires

Connect the speaker leads and set MODE SELECT switch and POWER MODE switch to suit the configura-

tion according to the figures shown below and the next page.

• When synchronously connecting two or more amplifiers in combination, only use these amplifiers. Do not

mix these amplifiers with other amplifiers.

• When synchronously connecting two or more amplifiers in combination, set the gain control, subsonic

select switch, cut off frequency control for LPF and bass boost control on the amplifier that has been set to

MASTER with the MODE SELECT switch. These settings are inactive when set on an amplifier set to

SYNC or SYNC INV.

CAUTION

Do NOT install or use this amplifier by wiring speakers rated at 2 Ω (or lower) in parallel to achieve a 1 Ω (or

lower) bridged mode (Diagram B).

Amplifier damage, smoke, and overheating could result from improper bridging. The amplifier surface could

also become hot to the touch and minor burns could result.

To properly install or use a bridged mode and achieve a 2 Ω load, wire two 4 Ω speakers in parallel with Left

+ and Right – (Diagram A) or use a single 2 Ω speaker.

If the synthetic impedance is from 2 Ω to less than 4 Ω, always make sure to set the POWER MODE switch to

the HI-CURRENT position.

In addition, refer to the speaker instruction manual for information on the correct connection procedure.

Single Amplifier

• Use speakers having an impedance from 1 Ω to 8 Ω.

• The setting of the POWER MODE switch varies according to the speaker impedance. See the “Setting the

Unit” section for details.

Diagram A - Proper

2 Ω Bridged Mode

4 Ω

Speaker

4 Ω

Speaker

Diagram B - Improper

1 Ω Bridged Mode

2 Ω

Speake

2 Ω

Speaker

MODE SELECT switch must

be in MASTER position.

Connect to a car stereo.

For details, see the “Connection Diagram”.

1 Ω to 8 Ω

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

Two Amplifier (Ex. Bridge)

• Only use speakers having an impedance of 2 Ω to 16 Ω. In addition, in the case of connecting multiple

speakers with a bridge, check that the synthetic impedance is at least 2 Ω.

• The setting of the POWER MODE switch varies according to the speaker impedance. Slide the POWER

MODE switch to the HI-CURRENT position if the impedance is from 2 Ω to less than 4 Ω, or slide it to the

NORMAL position if the impedance is from 4 Ω to 16 Ω. The same setting is used for both amplifiers.

• When switching to the SYNC INV mode, the seal over the MODE SELECT switch must be peeled off and

you can find SYNC INV switch. Peel off the seal after checking that connections are correct.

Two Amplifier

• Use speakers having an impedance from 1 Ω to 8 Ω.

• The setting of the POWER MODE switch varies according to the speaker impedance. See the “Setting the

Unit” section for details. The same setting is used for both amplifiers.

MODE SELECT switch

must be in SYNC INV

position.

Connecting wire with RCA

pin plugs (sold separately).

Connecting

speaker wire

(sold separately).

MODE SELECT switch

must be in SYNC position.

MODE SELECT switch must

be in MASTER position.

Connect to a car stereo.

For details, see the

“Connection Diagram”.

2 Ω to 16 Ω

1 Ω to 8 Ω

SYNC OUTPUT

MODE SELECT switch must

be in MASTER position.

Connect to a car stereo.

For details, see the

“Connection Diagram”.

Connecting wire with RCA

pin plugs (sold separately).

SYNC INPUT

SYNC OUTPUT

SYNC INPUT

Connecting the Unit

Four Amplifier (Ex. Bridge)

MODE SELECT switch

must be in MASTER position.

Connecting wire with RCA

pin plugs (sold separately).

MODE SELECT switch must

be in SYNC INV position.

Connect to a car stereo.

For details, see the

“Connection Diagram”.

MODE SELECT switch must be

in SYNC INV position.

MODE SELECT switch must

be in SYNC INV position.

Connecting wire with RCA

pin plugs (sold separately).

Connecting wire with RCA

pin plugs (sold separately).

Connecting speaker

wire (sold separately).

Connecting speaker

wire (sold separately).

SYNC OUTPUT

SYNC INPUT

SYNC OUTPUT

SYNC INPUT

2 Ω to

16 Ω

• Only use speakers having an impedance of 2 Ω to 16 Ω. In addition, in the case of connecting multiple

speakers with a bridge, check that the synthetic impedance is at least 2 Ω.

• The setting of the POWER MODE switch varies according to the speaker impedance. Slide the POWER

MODE switch to the HI-CURRENT position if the impedance is from 2 Ω to less than 4 Ω, or slide it to the

NORMAL position if the impedance is from 4 Ω to 16 Ω. The same setting is used for four amplifiers.

• When switching to the SYNC INV mode, the seal over the MODE SELECT switch must be peeled off and

you can find SYNC INV switch. Peel off the seal after checking that connections are correct.

SYNC OUTPUT

SYNC INPUT

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

Four Amplifier

MODE SELECT switch

must be in MASTER position.

Connect to a car stereo.

For details, see the

“Connection Diagram”.

Connecting wire with RCA

pin plugs (sold separately).

Connecting wire with RCA

pin plugs (sold separately).

Connecting wire with RCA

pin plugs (sold separately).

MODE SELECT switch

must be in SYNC position.

MODE SELECT switch

must be in SYNC position.

MODE SELECT switch

must be in SYNC position.

1 Ω to 8 Ω

SYNC OUTPUT

SYNC

INPUT

SYNC

OUTPUT

SYNC INPUT

• Use speakers having an impedance from 1 Ω to 8 Ω.

• The setting of the POWER MODE switch varies according to the speaker impedance. See the “Setting the

Unit” section for details. The same setting is used for four amplifiers.

SYNC OUTPUT

SYNC INPUT

Installation

CAUTION

• Do not install in:

—Places where it could injure the driver or pas-

sengers if the vehicle stops suddenly.

—Places where it may interfere with the driver,

such as on the floor in front of the driver’s

seat.

• Make sure that wires are not caught in the sliding

mechanism of the seats, resulting in a short-cir-

cuit.

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier.

Protect all cables and important equipment such

as fuel lines, brake lines and electrical wiring

from damage.

• Install tapping screws in such a way that the

screw tip does not touch any wire. This is impor-

tant to prevent wires from being cut by vibration

of the car, which can result in fire.

• DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could

become hot to the touch and minor burns could

result.

• To ensure proper installation, use the supplied

parts in the manner specified. If any parts other

than the supplied ones are used, they may damage

internal parts of the amplifier, or they may

become loose causing the amplifier to shut down.

• Never replace the fuse with one of greater value

or rating than the original fuse. Use of an improp-

er fuse could result in overheating and smoke and

could cause damage to the product and injury

including burns.

CAUTION:

To prevent malfunction and/or injury

• To ensure proper heat dissipation of the amplifier,

be sure of the following during installation.

—Allow adequate space above the amplifier for

proper ventilation.

—Do not cover the amplifier with a floor mat or

carpet.

• DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could

become hot to the touch and minor burns could

result.

• Do not install the amplifier on unstable places

such as the spare tire board.

• The best location for installation differs with the

car model and installation location. Secure the

amplifier at a sufficiently rigid location.

• Make temporary connections first and check that

the amplifier and the system operate properly.

• After installing the amplifier, confirm that the

spare tire, jack and tools can be easily removed.

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

Example of installation on the floor

mat or on the chassis

1. Place the amplifier where it is to be

installed. Insert the supplied tap-

ping screws (4 × 18 mm) into the

screw holes. Push on the screws with

a screwdriver so they make marks

where the installation holes are to

be located.

2. Drill 2.5 mm (1/8 inch) diameter

holes at the point marked, and

install the amplifier, either on the

carpet or directly to the chassis.

Replacing the terminal cover

1. Align the unit and terminal cover,

and insert the screw.

2. Tighten the screw with a 4 mm

hexagonal wrench.

Drill a 2.5 mm (1/8 inch)

diameter hole

Tapping-screws

(4 × 18 mm)

Floor mat

or chassis

Screw

Terminal Cover

Specifications

Power source ........................................................................................................ 14.4 V DC (10.8 V to 15.1 V allowable)

Grounding system .......................................................................................................................................... Negative type

Current consumption ........................................................................................................ 39 A (at continuous power, 4 Ω)

Average current drawn* .......................................................................................................... 12 A (4 Ω for one channel)

20 A (2 Ω for one channel)

28 A (1 Ω for one channel)

Fuse (external) ........................................................................................................................................................ 40 A × 2

Dimensions ...................................................................................................................... 304 (W) × 56 (H) × 195 (D) mm

[12 (W) × 2-1/4 (H) × 7-5/8 (D) in.]

Weight .................................................................................................... 2.9 kg (6.4 lbs.) (Leads for wiring not included)

Maximum power output ................................................................................ 800 W × 1 (4 Ω) / 1 200 W × 1 (1 Ω to 2 Ω)

Continuous power (14.4 V) ...................................... NORMAL mode: 4 Ω, 20 Hz to 240 Hz, 1.0% THD, 400 W × 1

2 Ω, 100 Hz, 1.0% THD, 600 W × 1

HI-CURRENT mode: 4 Ω, 20 Hz to 240 Hz, 1.0% THD, 150 W × 1

2 Ω, 100 Hz, 1.0% THD, 300 W × 1

1 Ω, 100 Hz, 1.0% THD, 600 W × 1

Load impedance ........................................................................................................................ 4 Ω (1 Ω to 8 Ω allowable)

Frequency response .......................................................................................................... 10 Hz to 240 Hz (+0 dB, –3 dB)

S/N ratio ........................................................................................................................................ 92 dB (IHF-A network)

Distortion .......................................................................................................................................... 0.5 % (10 W, 100 Hz)

Low pass filter ............................................................................................................ Cut off frequency: 40 Hz to 240 Hz

Cut off slope: –18 dB/oct

Subsonic filter (HPF) .............................................................................................................................. Frequency: 20 Hz

Slope: –18 dB

Bass boost ................................................................................................................................................ Frequency: 50 Hz

Level: 0 / 6 / 9 / 12 dB

Gain control .................................................................................................................................... RCA: 400 mV to 6.5 V

SP: 1.6 V to 26 V

Maximum input level / impedance ...................................................................................................... RCA: 6.5 V / 22 kΩ

SP: 26 V / 90 kΩ

Note:

• Specifications and the design are subject to possible modification without notice

due to improvements.

*Average current drawn

• The average current drawn is nearly the maximum current drawn by this unit

when an audio signal is input. Use this value when working out total current

drawn by multiple power amplifiers.

Power output .......................................................... NORMAL mode: 400 W RMS × 1 channel

(at 4 Ω and 1% THD+N)

600 W RMS × 1 channel

(at 100 Hz , 2 Ω and 1% THD+N)

HI-CURRENT mode: 150 W RMS × 1 channel

(at 4 Ω and 1% THD+N)

300 W RMS × 1 channel

(at 100 Hz , 2 Ω and 1% THD+N)

600 W RMS × 1 channel

(at 100 Hz , 1 Ω and 1% THD+N)

S/N ratio ................................................................................ 66 dBA (reference: 1 W into 4 Ω)

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

1
Avant d’utiliser cet appareil .................... 1
Visitez notre site Web ...................................... 2
Quelques mots concernant 
cet appareil  ................................................ 2
PRÉCAUTION .................................................. 2
ATTENTION .................................................... 2
Réglage de l’appareil ................................ 3
Couvre-bornes .................................................. 3
Témoin d’alimentation  ...................................... 3
Sélecteur infrasonore  ........................................ 3
Commande de l’accentuation des graves  .......... 3
Interrupteur BFC (Commande de fréquence 
de battement) .............................................. 3
Commutateur MODE SELECT  ........................ 4
Commande du gain ............................................ 4
Commande de la fréquence de 
coupure pour LPF  ...................................... 4
Sélecteur d’entrée .............................................. 4
Commutateur POWER MODE  ........................ 4
Raccordement de l’appareil  .................... 5
Schéma de raccordement  .................................. 6
Raccordement de la borne d’alimentation  ........ 7
Raccordement des bornes de sortie vers 
les haut-parleurs  ........................................ 8
Utilisation de l’entrée de haut-parleur  .............. 8
Connexion des câbles des haut-parleurs .............. 9
Installation ................................................ 13
Exemple d’installation sur le tapis de sol 
ou sur le châssis ........................................ 14
Remise en place du couvre-bornes .................. 14
Caractéristiques techniques  ................ 15
Nous vous remercions d’avoir porté votre
choix sur un appareil PIONEER. Il a été
conçu et fabriqué pour vous apporter de
nombreuses années de satisfaction.
En raison des problèmes posés par 
l’installation de cet appareil, Pioneer vous
conseille de consulter un professionnel.
Avant d’utiliser l’appareil, prenez 
connaissance de ce mode d’emploi et tout
spécialement des AVERTISSEMENTS.
Pour toute question concernant cet
appareil, veuillez vous adresser au 
revendeur ou à l’installateur.
Table des matières Avant d’utiliser cet appareil
Service après-vente pour un 
produit Pioneer
Pour toute question, et en particulier pour toute
question relative au service après-vente (y compris
celles qui relèvent de la garantie), veuillez vous
adresser au revendeur ou au distributeur auprès de
qui vous avez acquis ce produit. Dans l’hypothèse
où vous ne pourriez pas être renseigné comme
vous le désirez, consultez l’une des sociétés 
mentionnées ci-dessous.
N’expédiez pas le produit à l’une de ces sociétés,
quelle qu’en soit la raison, avant d’y avoir été
expressément invité.
7 Etats-Unis
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
7 Canada
Pioneer électroniques du Canada, Inc.
Département de service aux consomma-
teurs
300 Allstate Parkway
Markham, Ontario L3R OP2
1-877-283-5901
Pour toute question concernant la garantie,
veuillez consulter le document Garantie Limitée
qui accompagne le produit.

ENGLISH

FRANÇAIS

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

Visitez notre site Web

Rendez-nous visite sur le site suivant:

1 Enregistrez votre produit. Nous conserverons sur

fichier les détails de votre achat pour vous perme-

ttre de vous reporter à ces informations en cas de

déclaration de sinistre à votre assurance pour

perte ou vol.

2 Recevez les mises à jour sur les derniers produits

et les plus récentes technologies.

3 Téléchargez les manuels de l’utilisateur, com-

mandez les catalogues des produits, recherchez

de nouveaux produits, et bien plus.

Quelques mots concernant

cet appareil

Cet appareil est un amplificateur pour

haut-parleur d’extrême grave. Si les deux

canaux, L (gauche) et R (droit), sont

connectés à l’entrée cinch (RCA) de cet

appareil, la sortie est mixée parce que cet

appareil est un amplificateur monaural.

PRÉCAUTION

Ne remplacez pas le fusible par un fusible

de plus grande valeur ou de plus grand

calibre. L’utilisation d'un fusible inadapté

peut entraîner une surchauffe et de la

fumée, et peut provoquer l’endommage-

ment de l’appareil et des blessures, y com-

pris des brûlures.

ATTENTION

• Utilisez le faisceau de câbles de liaison à la

batterie (un câble rouge et un câble de masse) qui

est vendu séparément ([RD-223] et [RD-222]).

Reliez le câble rouge à la borne positive (+) de la

batterie et le câble de masse à la carrosserie du

véhicule. Le fusible risque de griller si un seul de

ce fils est connecté.

• Ne touchez pas l’amplificateur quand vous avez

les mains mouillées, faute de quoi vous risquez

de ressentir une secousse électrique. Pareillement,

ne touchez pas l’amplificateur s’il est mouillé.

• Pour votre sécurité et celles des autres usagers de

la route, maintenez le niveau d’écoute à une

valeur telle que les bruits de la circulation

demeurent nettement perceptibles.

• Si le fusible monté sur le câble de liaison à la

batterie, câble qui est vendu séparément, a grillé

ou bien s’il en est ainsi de celui de l’amplifica-

teur, vérifiez soigneusement toutes les connex-

ions d’alimentation. Recherchez la cause de

l’anomalie puis corrigez-la; enfin, remplacez le

fusible grillé par un fusible de même taille et de

même calibre.

• Pour éviter d’endommager l’amplificateur et les

haut-parleurs, le circuit de protection coupe

l’alimentation de l’amplificateur (les sons ne sont

plus émis) dès que survient une situation

anormale. Dans ce cas, mettez l’ensemble des

appareils hors tension et contrôlez les liaisons

entre l’amplificateur et les haut-parleurs. Le cas

échéant, recherchez la cause de l’anomalie et

corrigez-la.

• Consultez le revendeur si vous n’êtes pas en

mesure de résoudre le problème qui se pose à

vous.

• Pour éviter toute secousse électrique et tout

risque de court-circuit au cours des opérations de

raccordement et d’installation, n’oubliez pas de

débrancher le câble relié au pôle négatif de la

batterie (–) avant d’effectuer quelque opération

que ce soit.

• Avant d’effectuer un perçage requis par

l’installation de l’amplificateur, assurez-vous que

vous pouvez le faire sans danger pour les câbles,

canalisations, flexibles, etc., qui sont placés

derrière le panneau que vous devez percer.

• NE LAISSEZ PAS l’amplificateur entrer en con-

tact avec des liquides à cause, par exemple, de

l’emplacement où il a été placé. Cela pourrait

entraîner une secousse électrique. De plus, le con-

tact avec un liquide pourrait endommager l’am-

plificateur et les enceintes, produire de la fumée

ou surchauffer l’appareil. Enfin, la surface de

l’amplificateur et des enceintes connectées peut

devenir chaude au toucher et entraîner de légères

brûlures.

Réglage de l’appareil

Témoin

d’alimentation

Ce témoin s’éclaire

lorsque l’amplificateur

est sous tension.

Interrupteur BFC (Commande de

fréquence de battement)

L’interrupteur BFC se trouve sous l’appareil.

Si vous entendez un battement pendant

l’écoute d’une transmission AM avec votre

autoradio, changer la position de

l’interrupteur BFC en utilisant un petit

tournevis standard.

Couvre-bornes

Avant de mettre l’appareil en place,

dévissez les vis avec un tournevis à

pointe hexagonale de 4 mm et retirez le

couvre-bornes.

Commande de l’accentua-

tion des graves

Vous pouvez choisir un niveau

d’accentuation de 0, 6, 9 ou 12 dB.

Pour connaître la manière de relier

le boîtier de télécommande

d’accentuation des graves à

l’amplificateur, reportez-vous à la

section “Schéma de raccordement”.

Sélecteur infrasonore

Le filtre infrasonore coupe les

fréquences inférieures à 20 Hz afin de

supprimer les vibrations indésirables et

de réduire les pertes de puissance.

• Pour ajuster les commutateurs, utilisez un tournevis standard si nécessaire.

La page charge ...

Pioneer Car Amplifier PRS-D1100M Manuel utilisateur

Marque: Pioneer

Modèle: Car Amplifier PRS-D1100M

Catégorie: Amplificateurs audio

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Pioneer Car Amplifier PRS-D1100M User manual
español: Pioneer Car Amplifier PRS-D1100M Manual de usuario

Pioneer Car Amplifier PRS-D1100M Manuel utilisateur

Ce manuel convient également à

Pioneer Car Amplifier PRS-D1100M Manuel utilisateur

dans d''autres langues

Documents connexes