Yamaha RS700 Le manuel du propriétaire

Marque: Yamaha

Modèle: RS700

Catégorie: Tuners audio

Taper: Le manuel du propriétaire

Owner’s Manual

Network Receiver

• The R-N303 and R-N303D network receivers allow you to play back sound in

high-quality stereo at your own home.

• This manual explains preparations and operations for everyday users of the unit.

i En

English

PLEASE READ CAREFULLY BEFORE USE. BE SURE TO FOLLOW THESE INSTRUCTIONS.

The precautions listed below are to prevent risk of harm to the user and others, as well as to prevent property

damage, and to help the user use this unit properly and safely. Be sure to follow these instructions.

After reading this manual, be sure to keep it in a safe place where

it can be referenced at any time.

WARNING

This content indicates “risk of serious injury or death.”

■ Power supply/power cord

• Do not do anything that could damage the power cord.

- Do not place it near a heater.

- Do not bend it excessively or alter it.

- Do not scratch it.

- Do not place it under a heavy object.

Using the power cord with the core of the cord exposed could

cause electric shocks or a fire.

• Do not touch the power plug or cord if there is a chance of

lightning. Failure to observe this may cause electric shocks.

• Use this unit with the power supply voltage printed on it.

Failure to connect to an appropriate AC outlet may cause a fire,

electric shocks, or malfunctions.

• Check the electric plug periodically and remove any dirt or dust

which may have accumulated on it. Failure to observe this may

cause a fire or electric shocks.

• When setting up the unit, make sure that the AC outlet you are

using is easily accessible. If some trouble or malfunction

occurs, immediately turn off the power switch and disconnect

the plug from the AC outlet. Even when the power switch is

turned off, as long as the power cord is not unplugged from the

wall AC outlet, the unit will not be disconnected from the

power source.

• If you hear thunder or suspect approaching lightning, quickly

turn off the power switch and pull the power plug from the AC

outlet. Failure to observe this may cause a fire or malfunctions.

• If not using the unit for long periods of time, be sure to pull the

power plug from the AC outlet. Failure to observe this may

cause a fire or malfunctions.

■ Do not disassemble

• Do not disassemble or modify this unit. Failure to observe this

may cause a fire, electric shocks, injury, or malfunctions. If you

notice any irregularities, be sure to request an inspection or

repair from the dealer where you purchased the unit or from

qualified Yamaha service personnel.

■ Water warning

• Do not expose the unit to rain, use it near water or in damp or

wet conditions, or place on it any containers (such as vases,

bottles or glasses) containing liquids which might spill into any

openings. A liquid such as water getting into the unit may cause

a fire, electric shocks, or malfunctions. If any liquid such as

water seeps into the device, turn off the power immediately and

unplug the power cord from the AC outlet. Then, request an

inspection from the dealer where you purchased the unit or from

qualified Yamaha service personnel.

• Never insert or remove an electric plug with wet hands. Do not

handle this unit with wet hands. Failure to observe this may

cause electric shocks or malfunctions.

■ Fire warning

• Do not place any burning items or open flames near the unit,

since they may cause a fire.

■ Maintenance and care

• Do not use aerosols or spray-type chemicals that contain

combustible gas for cleaning or lubrication. The combustible

gas will remain inside the unit, which may cause explosion or

fire.

■ Battery use

• Do not disassemble a battery. If the contents of the battery get

on your hands or in your eyes, it can cause blindness or

chemical burns.

• Do not dispose of batteries in fire. Doing so may result in the

battery bursting, causing a fire or injury.

• Do not expose a battery to high temperatures, such as direct

sunlight or a fire. The battery may burst, causing a fire or injury.

• Do not attempt to recharge batteries that are not intended to be

charged. Charging could cause the battery to burst or leak,

which can cause blindness, chemical burns, or injury.

• If the batteries do leak, avoid contact with the leaked fluid.

If the battery fluid should come in contact with your eyes,

mouth, or skin, wash immediately with water and consult a

doctor. Battery fluid is corrosive and may possibly cause loss of

sight or chemical burns.

■ Wireless unit

• Do not use this unit near medical devices or inside medical

facilities. Radio waves from this unit may affect electromedical

devices.

• Do not use this unit within 15 cm (6 in) of persons with a heart

pacemaker implant or a defibrillator implant. Radio waves from

this unit may affect electro-medical devices, such as a heart

pacemaker implant or defibrillator implant.

■ If you notice any abnormality

• If any of the following abnormalities occur, immediately turn

off the power and disconnect the power plug. If you are using

batteries, remove the batteries from this unit.

- The power cord/plug is damaged.

- An unusual smell or smoke is emitted from the unit.

- Foreign material gets into the interior of the unit.

- There is a loss of sound during use.

- There is a crack or damage in the unit.

Continued use could cause electric shocks, a fire, or

malfunctions. Immediately request an inspection or repair from

PRECAUTIONS

• Be sure to request inspections or repairs from the dealer

where you purchased the unit or from qualified Yamaha

service personnel.

• Yamaha cannot be held responsible for damage caused by

improper use or modifications to the unit.

• This product is for ordinary homes. Do not use for

applications requiring high reliability, such as managing

lives, health care or high-value assets.

ii En

English

the dealer where you purchased the unit or from qualified

Yamaha service personnel.

• Be careful not to drop or apply strong impact to this unit. If you

suspect the unit may have been damaged due to dropping or

impact, immediately turn off the power and pull the power plug

from the AC outlet. Failure to observe this may cause electric

shocks, a fire, or malfunctions. Immediately request an

inspection from the dealer where you purchased the unit or from

qualified Yamaha service personnel.

CAUTION

This content indicates “risk of injury.”

■ Power supply/power cord

• Do not use an AC outlet where the power plug fits loosely when

inserted. Failure to observe this may cause a fire, electric

shocks, or burns.

• When removing the electric plug from an AC outlet, always

hold the plug itself and not the cord. Pulling by the cord can

damage it and cause electric shocks or a fire.

• Insert the power plug firmly all the way into the AC outlet.

Using the unit when it is not plugged in sufficiently can cause

dust to accumulate on the plug, causing a fire or burns.

■ Installation

• Do not place the unit in an unstable position where it might

accidentally drop or fall over and cause injuries.

• Do not block this unit's ventilation holes (cooling slits). This

unit has ventilation holes on the top/bottom to prevent the

internal temperature from becoming too high. Failure to

observe this may trap heat inside the unit, causing a fire or

malfunctions.

• When installing this unit:

- Do not cover it with any cloth.

- Do not install it on a carpet or rug.

- Make sure the top surface faces up; do not install on its sides

or upside down.

- Do not use the device in a confined, poorly-ventilated

location.

Failure to observe the above may trap heat inside the unit,

causing a fire or malfunctions. Ensure that there is adequate

space around the unit: at least 30 cm (11-3/4 in) on top, 20 cm

(7-7/8 in) on the sides, and 20 cm (7-7/8 in) on the rear.

• Ensure that the top is facing upwards. Failure to observe this

may cause malfunctions or for the unit to fall and cause injury.

• Do not place the unit in a location where it may come into

contact with corrosive gases or salt air. Doing so may result in

malfunction.

• Avoid being near the unit during a disaster, such as an

earthquake. Since the unit may turn over or fall and cause

injury, quickly move away from the unit and go to a safe place.

• Before moving this unit, be sure to turn off the power switch and

disconnect all connection cables. Failure to observe this may

damage the cables or cause you or someone else to trip and fall.

■ Hearing loss

• Do not use the unit/speakers or headphones for a long period of

time at a high or uncomfortable volume level, since this can

cause permanent hearing loss. If you experience any hearing

loss or ringing in the ears, consult a physician.

• Before connecting the unit to other devices, turn off the power

for all devices. Also, before turning the power of all devices on

or off, make sure that all volume levels are set to the minimum.

Failing to do so may result in hearing loss, electric shock, or

device damage.

• When turning on the AC power in your audio system, always

turn on the unit LAST, to avoid hearing loss and speaker

damage. When turning the power off the unit should be turned

off FIRST for the same reason. Failure to observe the above

may cause hearing impairment or speaker damage.

■ Maintenance

• Remove the power plug from the AC outlet when cleaning the

unit. Failure to observe this may cause electric shocks.

■ Handling caution

• Do not insert foreign materials such as metal or paper into the

ventilation holes of this unit. Failure to observe this may cause a

fire, electric shocks, or malfunctions. If foreign material gets

into the unit, immediately shut off the power and pull the power

plug from the AC outlet / then turn off any amplifiers and

receivers and request an inspection from the dealer where you

purchased the unit or from qualified Yamaha service personnel.

• Do not rest your weight on the unit or place heavy objects on it.

Avoid applying excessive force to the buttons, switches or

connectors. Failure to observe the above may cause injury or

unit damage.

• Avoid pulling the connected cables to prevent injuries or

damage to the unit by causing it to fall.

■ Battery use

• Always replace all batteries at the same time. Do not use new

batteries together with old ones. Using new ones with old ones

could cause a fire, burns, or inflammation due to fluid leaks.

• Do not mix battery types, such as alkaline batteries with

manganese batteries, or batteries from different makers, or

different types of batteries from the same maker, since this can

cause a fire, burns, or inflammation due to fluid leaks.

• Keep batteries away from children. A child could accidentally

swallow a battery. Failure to observe this may also cause

inflammation due to battery fluid leaks.

• Do not put in a pocket or bag, carry, or store batteries together

with pieces of metal. The battery could short, burst, or leak,

causing a fire or injury.

• Always make sure all batteries are inserted in conformity with

the +/- polarity markings. Failure to do so might result in a fire,

burns, or inflammation due to fluid leaks.

• When the batteries run out, or if the unit is not to be used for a

long time remove the batteries from the remote control to

prevent possible leakage of the battery fluid.

• When storing or discarding batteries, insulate the terminal area

by applying tape, or some other protection. Mixing them with

other batteries or metal objects can cause a fire, burns, or

inflammation due to fluid.

Caution

Do not touch the surface marked with

this label.

The surface may become hot during

operation.

iii En

Notice

Indicates points that you must observe in order to

prevent product failure, damage or malfunction and

data loss, as well as to protect the environment.

■ Power

• Indicates points that you must observe in order to prevent

product failure, damage or malfunction and data loss, as well as

to protect the environment.

■ Installation

• Do not use this unit in the vicinity of other electronic

equipment, such as a TV, radio or mobile phone. Failure to

observe this may cause this unit or the TV or radio to produce

noise.

• Do not use this unit in a location that is exposed to direct

sunlight (such as a vehicle interior), that becomes extremely

hot, such as near a heater, or extremely cold, or that is subject to

excessive dust or vibration. Failure to observe this may cause

the unit's panel to become deformed, the internal components to

malfunction, or for operation to become unstable.

• Install this unit as far away from other electronic equipment as

possible. Digital signals from this unit may interfere with other

electronic equipment.

• If using a wireless network or Bluetooth, avoid installing this

unit near metal walls or desks, microwave ovens, or other

wireless network devices.

■ Connections

• If connecting external units, be sure to thoroughly read the

manual for each unit and connect them in accordance with the

instructions. Failure to properly handle a unit in accordance

with the instructions could cause malfunctions.

• Do not connect this unit to industrial units. Digital audio

interface standards for consumer use and industrial use are

different. This unit has been designed to connect to a consumer-

use digital audio interface. Connections to an industrial-use

digital audio interface could not only cause this unit to

malfunction, but could also damage the speakers.

■ Handling

• Do not place vinyl, plastic, or rubber products on this unit.

Failure to observe this may cause discoloration or deformation

in the panel of this unit.

• If the ambient temperature changes drastically (such as during

unit transportation or under rapid heating or cooling) and there

is a chance condensation may have formed in the unit, leave the

unit for several hours without turning on the power until it is

completely dry before use. Using the unit while there is

condensation can cause malfunctions.

■ Maintenance

• When cleaning the unit, use a dry, soft cloth. Using chemicals

such as benzine or thinner, cleaning agents, or chemical

scrubbing cloths can cause discoloration or deformation.

■ Batteries

• Be sure to discard used batteries in accordance with local

regulations.

Information

Indicates information of note regarding this product.

■ About content in this manual

• The illustrations and screens in this manual are for instructional

purposes only.

• The company names and product names in this manual are the

trademarks or registered trademarks of their respective

companies.

• Software may be revised and updated without prior notice.

• Information marked by the “ WARNING” icon indicates

points that may lead to death or serious injury if not observed.

• Information marked with the “ CAUTION” icon indicates

points that may lead to injury if not observed.

• Information in the “Notice” sections indicates points that you

must observe to prevent product failure, damage or malfunction

and data loss.

• Information listed in the “Note” sections indicates

supplementary information.

• This manual describes the “iPod touch”, “iPhone” and “iPad”

collectively as the “iPhone”. (“iPhone” refers to the “iPod

touch”, “iPhone” and “iPad”, unless otherwise specified.)

• In this manual, illustrations of English menu screens are used as

examples.

Notice and Information

Contents

1 En

English

PREPARATION INTRODUCTION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

INTRODUCTION

What you can do with this unit ................................. 2

Sources that can be played back on this unit ................. 2

Supplied accessories ................................................... 3

Controls and functions ............................................... 4

Front panel ..................................................................... 4

Front display .................................................................. 6

Rear panel ...................................................................... 7

Remote control............................................................... 8

PREPARATION

Connections ............................................................... 10

Connecting audio devices ............................................ 10

Connecting the speakers .............................................. 11

Connecting the FM/AM antennas (R-N303) ............... 12

Connecting the DAB/FM antenna (R-N303D)............ 12

Connecting the network cable ..................................... 13

Preparing a wireless antenna ....................................... 13

Connecting power cord................................................ 13

Turning on the unit ...................................................... 13

Connecting to a network .......................................... 14

Sharing the iOS device setting..................................... 15

Configuring with the router’s WPS push button ......... 16

Set the wireless network connection manually............ 16

Connecting a mobile device to the unit directly

(Wireless Direct) ..................................................... 17

Verify the network connection status .......................... 18

Configuring MusicCast................................................ 19

BASIC OPERATION

Playback .................................................................... 20

Playing a source........................................................... 20

Switching information on the front display................. 20

Using the sleep timer ................................................... 21

Listening to FM/AM radio....................................... 22

FM/AM tuning............................................................. 22

Using preset functions ................................................. 22

Radio Data System tuning

(Only for U.K. and Europe models) ........................ 25

Listening to DAB radio (R-N303D)......................... 26

Preparing the DAB tuning ........................................... 26

Selecting a DAB radio station for reception................ 26

Using preset function................................................... 27

Displaying the DAB information................................. 28

Checking reception strength of each DAB channel

label ......................................................................... 29

Playing back music via Bluetooth............................ 30

Connecting a Bluetooth device (pairing) ..................... 30

Playing back Bluetooth device contents ...................... 30

Disconnecting a Bluetooth connection ........................ 31

Playing back music stored on media servers

(PCs/NAS) ............................................................. 32

Setting the media sharing of music files...................... 32

Playback of PC music contents.................................... 33

Listening to Internet radio....................................... 34

Playing back music with AirPlay ............................ 35

Playback of iTunes/iPhone music contents ................. 35

Registering the current playback song/station

(Preset function) ....................................................36

Registering to a preset ................................................. 36

Recalling a preset......................................................... 36

Clearing a preset .......................................................... 36

ADVANCED OPERATION

Configuring playback settings for different

playback sources (OPTION menu)......................37

OPTION menu items ................................................... 37

Configuring various functions (SETUP menu) ......39

SETUP menu items ..................................................... 39

Network ....................................................................... 40

Bluetooth ..................................................................... 41

Balance ........................................................................ 41

Max Volume ................................................................ 41

InitialVolume............................................................... 42

AutoPowerStby (Auto Power Standby)....................... 42

Configuring the system settings

(ADVANCED SETUP menu)...............................43

ADVANCED SETUP menu items .............................. 43

Checking the firmware version (VERSION)............... 43

Selecting the remote control ID (REMOTE ID).......... 43

Setting tuner frequency step (TU) ............................... 43

Restoring the default settings (INIT)........................... 43

Updating the firmware (UPDATE) ............................. 44

Updating the unit’s firmware...................................45

ADDITIONAL INFORMATION

Troubleshooting.........................................................46

Supported devices and file formats .........................52

Supported devices........................................................ 52

Supported file formats ................................................. 52

Specifications .............................................................53

Trademarks ...............................................................55

Index ...........................................................................56

Contents

2 En

INTRODUCTION

This unit is a network receiver compatible with a network source such as a media server and mobile device.

It supports playback from not only analog sources such as a CD player or AM/FM radio, but also from Bluetooth devices

and network streaming services.

Sources that can be played back on this unit

You need a commercially available wireless router (access point) when you use a mobile device.

1 Play back the Internet radio (p. 34)

2 Play back the streaming service

(See the supplement for each service.)

3 Play back music files stored on your PC (p. 32)

4 Play back music files stored on your NAS

(p. 32)

5 Play back music files with AirPlay (p. 35)

6 Play back audio content from Bluetooth

devices (p. 30)

7 Play back your external component (p. 10)

8 Listening to radio (p. 22, 26)

Note

For details on connecting the external devices, see “Connections” (p. 10).

What you can do with this unit

SPEAKERSPHONES

VOLUME

SELECT

BLUETOOTH

RETURN

PUSH ENTER

CONNECT

DISPLAY MODE

MEMORY BAND

PRESET

TUNING

BASS

TREBLE

INPUT

This unit

1 Internet

2 Streaming service

Modem

Router*

3 PC

5 AirPlay (iTunes)

4 NAS

5 AirPlay (iPhone/iPad/iPod touch)

6 Bluetooth

7 CD player etc.

Mobile

device

8 Radio

What you can do with this unit

3 En

English

INTRODUCTION

Check that the following accessories are supplied with the product.

Supplied accessories

Network Receiver

Réseau Ampli-Tuner

Remote control FM antenna (R-N303)AM antenna (R-N303)

Batteries (x2)

(AA, R6, UM-3)

DAB/FM antenna

(R-N303D)

One of the above is supplied depending

on the region of purchase.

R-N303/R-N303D Owner’s Manual

CD-ROM (Europe model)

R-N303/R-N303D Owner’s Manual

(except Europe model, this book)

R-N303/R-N303D Quick Start Guide

(Europe model)

Network Receiver

4 En

Front panel

1 A (power)

Turns on/off (standby) the unit.

2 STANDBY/ON indicator

Brightly lit: Power is on

Dimly lit: Standby mode

Note

When not using this unit for an extended period of time, be sure

to unplug it from the power outlet. This unit uses a minimal

amount of power even in standby mode.

3 Front display

Shows information about the operational status of this

unit (p. 6).

4 DISPLAY

Selects the information displayed on the front display

(p. 20).

5 MODE

Sets the FM band reception mode to automatic stereo

or monaural (p. 22).

6 MEMORY

Registers the current radio station as a preset when

TUNER is selected as the input source (p. 23, 27).

Registers the current playback song or streaming

station as a preset when NET are selected as the input

source (p. 36).

7 BAND

Sets the radio tuner band when TUNER is selected as

the input source. (p. 22, 26)

8 PRESET j / i

Recalls a preset radio station (p. 24, 22) or song/

streaming station (p. 36).

9 BLUETOOTH indicator

Lights up when the unit is connecting to a Bluetooth

device.

0 Wi-Fi indicator

This lights when connecting to a wireless network, or

when the unit is operating as an access point.

It also lights up if you register the unit with the

MusicCast CONTROLLER app, even if the unit is

connected to a wired network.

A Remote control sensor

Receives infrared signals from the remote control.

B TUNING jj / ii

Selects the tuning frequency (p. 22) or a DAB radio

station (p. 26) when TUNER is selected as the input

source.

Controls and functions

SPEAKERSPHONES

VOLUME

SELECT

BLUETOOTH

RETURN

PUSH ENTER

CONNECT

DISPLAY MODE

MEMORY BAND

PRESET

TUNING

BASS

TREBLE

INPUT

1 2 3 0954 6 7

H JIC

ED F G

8 BA

5 En

Controls and functions

English

INTRODUCTION

C PHONES jack

Outputs audio to your headphones for private

listening.

D SPEAKERS A/B

Turns on or off the speaker set connected to the

SPEAKERS A and/or SPEAKERS B terminals on the

rear panel each time the corresponding button is

pressed.

E BASS +/–

Increases or decreases the low frequency response.

Control range: –10 to +10 (20 Hz)

F TREBLE +/–

Increases or decreases the high frequency response.

Control range: –10 to +10 (20 kHz)

G INPUT l / h

Selects the input source you want to listen to.

H SELECT/ENTER (jog dial)

Turn the dial to select a numeric value or setting, and

press the dial to confirm.

I RETURN

Returns to the previous indication of the front display.

CONNECT

Use to control the unit using the dedicated MusicCast

CONTROLLER app for mobile devices.

See MusicCast Setup Guide for details.

J VOLUME control

Increases or decreases the sound output level.

6 En

Controls and functions

Front display

Note

You can change the brightness level of the front display by pressing DIMMER (p. 8).

1 Information display

Displays the current status (such as input name).

You can switch the information that is displayed when

you press DISPLAY (p. 20).

2 STEREO indicator

Lights up when the unit is receiving a stereo FM radio

signal.

3 TUNED indicator

Lights up when the unit is receiving an FM/AM radio

station signal.

Note

AM radio is available only for R-N303.

4 Speaker indicators

“SP A” lights up when the SPEAKERS A output is

enabled and “SP B” lights up when the SPEAKERS B

output is enabled.

5 MUTE indicator

Blinks when audio is muted.

6 SLEEP indicator

Lights up when the sleep timer is on (p. 21).

STEREO SP

MUTE

TUNED

SLEEP

42 3 5 6

7 En

Controls and functions

English

INTRODUCTION

Rear panel

1 SERVICE jack

This jack is for support use, and is normally not used.

2 NETWORK jack

For connecting to a network with a network cable

(p. 13).

3 ANTENNA terminals

For connecting to the radio antennas (p. 12).

4 Wireless antenna

For connecting to a network device wirelessly (p. 13).

5 Power cord

For connecting to an AC wall outlet (p. 13).

6 OPTICAL jack

For connecting to audio components equipped with

optical digital output (p. 10).

7 COAXIAL jack

For connecting to audio components equipped with a

coaxial digital output (p. 10).

8 PHONO jacks (R-N303 except Europe model)

For connecting to a turntable (p. 10).

9 CD jacks

For connecting to a CD player (p. 10).

0 LINE 1-3 jacks

(R-N303 Europe model, R-N303D)

LINE 1-2 jacks (R-N303 except Europe model)

For connecting to analog audio components (p. 10).

A SPEAKERS terminals

Used to connect speakers (p. 11).

B VOLTAGE SELEC TOR

(Only for General model)

SPEAKERS

ANTENNA

GND

PHONO LINE

OUT

CLASS 2 WIRING

CABLAGE CLASSE 2

A OR B:

8Ω

MIN.

SPEAKER

NETWORK

SERVICE

DIGITAL

OPTICAL

COAXIAL

VOLTAGE SELECTOR

22020

240 V

CD LINE

OUT

76A

1324 5

089

9 0

(R-N303 except Europe model)

* The R-N303 Europe model and R-N303D are as shown below.

8 En

Controls and functions

Remote control

1 Infrared signal transmitter

Sends infrared signals.

2 A (power)

Turns on/off (standby) the unit.

3 SLEEP

Sets the sleep timer (p. 21).

4 DIMMER

Changes the brightness level of the front display.

Choose brightness from 5 levels by pressing this key

repeatedly.

5 SPEAKERS A/B

Turns on and off the set of speakers connected to the

SPEAKERS A and/or SPEAKERS B terminals on the

rear panel of this unit when the corresponding key is

pressed.

6 Input selection keys

Select the input source you want to listen to.

Note

NET key is for network source. Press repeatedly to select a

desired network source.

7 Radio keys

Operate the radio.

BAND Sets the radio tuner band when

TUNER is selected as the input

source (p. 22, 26).

TUNING jj / ii Selects the tuning frequency

(p. 22) or a DAB radio station

(p. 26) when TUNER is selected

as the input source.

8 MEMORY

Registers the current radio station as a preset when

TUNER is selected as the input source (p. 23, 27).

Registers the current playback song or streaming

station as a preset when NET are selected as the input

source (p. 36).

9 CLEAR

Deletes the preset memory (p. 24, 28, 36).

0 MODE

Sets the FM band reception mode to automatic stereo

or monaural (p. 22).

A Menu operation keys

Cursor keys Selects a menu, setting value or

other parameter.

ENTER Confirms a selected item.

RETURN Returns to the previous state.

B HOME

Moves up top level when selecting music files,

folders, etc.

C SETUP

Displays the “SETUP” menu (p. 39).

D NOW PLAYING

Displays music information when selecting music

files, folders, etc.

LINE 1

TUNER NET

BLUETOOTH

BAND

PRESET

TUNING

MUTE

NOW PLAYING

RETURN

OPTION

VOLUME

CLEAR MODE DISPLAY

MEMORY

LINE 2 PHONO

ENTER

DIMMER

SLEEP

SPEAKERS

OPTICAL

COAXIAL

HOME

SETUP

REPEAT

SHUFFLE

(R-N303, except Europe model)

9 En

Controls and functions

English

INTRODUCTION

E Playback keys

Let you play back and perform other operations for

network sources and Bluetooth devices.

Note

Yamaha does not guarantee the operation of all Bluetooth devices.

F PRESET j / i

Recalls a preset radio station (p. 24, 22) or song/

streaming station (p. 36).

G DISPLAY

Selects the information displayed on the front display

(p. 20).

H OPTION

Displays the “OPTION” menu (p. 37).

I MUTE

Mutes the audio output.

J VOLUME +/–

Increases or decreases the sound output level.

■ Installing batteries

Change all batteries if you notice the operation range of

the remote control narrows. Before inserting new

batteries, wipe the battery compartment clean.

■ Operation range

Point the remote control at the remote control sensor on

this unit and remain within the operating range shown

below. The area between the remote control and this unit

must be clear of large obstacles.

AA, R6, UM-3 batteries

Approximately

6 m (20 ft)

Remote control

10 En

PREPARATION

Connecting audio devices

Make sure to connect L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will

be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and

lack bass. Refer to the owner’s manual for each of your components.

Make sure to use RCA cables to connect audio components.

CAUTION

• Do not connect this unit or other components to the main power until all connections between components are

complete.

• Do not let bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the

speakers.

Note

The input jacks are different on the R-N303 Europe model and on the R-N303D (p. 7).

Connections

Only PCM signals can be input to the digital (OPTICAL/COAXIAL) jacks of this unit.

SPEAKERS

ANTENNA

GND

PHONO LINE

OUT

CLASS 2 WIRING

CABLAGE CLASSE 2

A OR B:

8Ω

MIN.

SPEAKER

NETWORK

SERVICE

DIGITAL

OPTICAL

COAXIAL

Audio

input

Audio

output

Speakers B

DVD player, etc.

Audio output

(digital coaxial)

Audio output

(digital optical)

CD player, etc.

Audio

output

CD player

CD recorder, etc.

Speakers A

(R-N303 except Europe model)

Turntable

Audio

output

GND

11 En

Connections

English

PREPARATION

Note

• Do not bundle audio cables and speaker cables together with the

power cord. Doing so may generate noise.

• The PHONO jacks are designed for connecting a turntable with

an MM cartridge.

• Connect your turntable to the GND terminal to reduce noise in

the signal. However, for some turntables, you may hear less

noise without the GND connection.

• On the R-N303D and R-N303 Europe models, to prevent sound

loops, no sound will be outputted from the LINE 3(OUT) jack

while the LINE 3 input is selected. On other models, no sound

will be outputted from the LINE 2(OUT) jack while the LINE 2

input is selected.

Connecting the speakers

CAUTION

Connect the speakers with an impedance as shown below.

If you connect speakers with an excessively low

impedance, this unit may overheat.

■ Connecting speaker cables

aRemove approximately 10 mm (3/8") of insulation

from the ends of the speaker cable and twist the bare

wires of the cable firmly together.

bLoosen the speaker terminal.

cInsert the bare wires of the cable into the gap on the

side (upper right or bottom left) of the terminal.

dTighten the terminal.

Note

When inserting speaker cables into the speaker terminals, insert

only the bare speaker wire. If insulated cable is inserted, the

connection may be poor and sound may not be heard.

■ Connecting via banana plug

(North America, Australia,

General models only)

Tighten the knob and then insert the banana plug into the

end of the corresponding terminal.

■ Bi-wire connection

Bi-wire connection separates the woofer from the

combined midrange and tweeter section. A bi-wire

compatible speaker has four binding post terminals. These

two sets of terminals allow the speaker to be split into two

independent sections. With these connections, the mid and

high frequency drivers are connected to one set of terminals

and the low frequency driver to another set of terminals.

Connect the other speaker to the other set of terminals in

the same way.

Note

• When making bi-wire connections, remove the shorting bridges

or cables on the speaker. Refer to the speakers’ instruction

manuals for more information.

• To use the bi-wire connections, press SPEAKERS A and

SPEAKERS B (p. 8) so that both speaker indicators (“SP A”

and “SP B”) light up on the front display.

Speaker connection Speaker impedance

SPEAKERS A or

SPEAKERS B

8  or higher

SPEAKERS A and

SPEAKERS B

16  or higher

(except for North America model)

Bi-wiring 8  or higher

10 mm

(3/8")

Red:positive (+)

Black:negative (–)

Banana plug

SPEAKER

CLASS 2 WI

CABLAGE CL

A OR B:

8Ω

MIN.

This unit

Speaker

SPEAKERSPHONES

VOLUME

SELECT

RETURN

PUSH ENTER

CONNECT

DISPLAY MODE

MEMORY BAND

PRESET

TUNING

BASS

TREBLE

INPUT

SPEAKERS A/B

DIMMER

SLEEP

SPEAKERS

OPTICAL

COAXIAL

SPEAKERS A/B

12 En

Connections

Connecting the FM/AM antennas

(R-N303)

Connect the supplied FM/AM antenna to this unit.

Fix the end of the FM antenna to a wall, and place the AM

antenna.

Note

• If you experience poor reception quality, install an outdoor

antenna.

• Unwind only the length of cable needed from the AM antenna

unit.

• The wires of the AM antenna have no polarity.

■ Assembling the supplied AM antenna

■ Connecting the wires of the AM antenna

Connecting the DAB/FM antenna

(R-N303D)

Connect the supplied DAB/FM antenna to this unit and fix

the antenna ends to a wall.

Note

• If you experience poor reception quality, install an outdoor

antenna.

• The antenna should be stretched out horizontally.

ANTENNA

GND

PHONO LINE

OUT

NETWORK

SERVICE

DIGITAL

OPTICAL

COAXIAL

FM antenna AM antenna

(except Europe model)

Insert

Hold down

ANTENNA

OUT

NETWORK

SERVICE

DIGITAL

OPTICAL

COAXIAL

LINE

FMDAB

DAB/FM antenna

13 En

Connections

English

PREPARATION

Connecting the network cable

Connect the unit to your router with a commercially-

available STP network cable (CAT-5 or higher straight

cable).

Note

Use STP (Shielded Twisted Pair) cable to prevent

electromagnetic interference.

Preparing a wireless antenna

If you connect the unit wirelessly, erect the wireless

antenna. For information on how to connect the unit to a

wireless network, see “Connecting to network” (p. 14).

For more information on using this unit with a Bluetooth

device, see “Playing back music via Bluetooth” (p. 30).

Notice

Do not apply excessive force on the wireless antenna. Doing so

may damage the antenna.

Connecting power cord

Plug the power cord into an AC wall outlet after all other

connections are complete.

WARNING

Only for General model:

Before connecting the power cord, make sure you set

VOLTAGE SELECTOR of this unit according to your

local voltage. Improper setting of VOLTAGE SELECTOR

may cause fire and damage to this unit.

Turning on the unit

Press A (power) to turn on the unit.

ANTENNA

NETWORK

SERVICE

LAN

WAN

Network Attached

Storage

(NAS)

Internet

Modem

Router

Network cable

This unit (rear)

Mobile device

(such as iPhone)

(R-N303)

MAINS

VOLTAGE SELECTOR

22020

240 V

VOLTAGE SELECTOR

22020

240 V

To the AC wall outlet

with the power cord

LINE 1

TUNER NET

BLUETOOTH

BAND

PRESET

TUNING

CLEAR MODE DISPLAY

MEMORY

LINE 2 PHONO

DIMMER

SLEEP

SPEAKERS

OPTICAL

COAXIAL

(power)

14 En

There are several methods to connect the unit to a network. Select a connection method according to your environment.

Note

• Some security software installed on your PC or the firewall settings of network devices (such as a router) may block the access of the

unit to the network devices or the Internet. In these cases, configure the security software or firewall settings appropriately.

• Each server must be connected to the same subnet as the unit.

• To use the service via the Internet, broadband connection is strongly recommended.

• When playing a high-resolution audio source via the network, we recommend connecting by cable to the router for stable playback.

■ Connecting with a wireless router (access point)

Connect to the network with the method listed below that corresponds to your environment.

■ Connecting to a router using a cable

Note

• For information on how to set the IP address and other menu items, please refer to page 40.

• To switch from a wireless LAN connection to a wired LAN connection, set the “Connection” under the “Network” setup menu to

“Wired” (p. 40).

Connecting to a network

WAC (Wireless Accessory Configuration)

If you turn on the power to the unit right after you purchase or

initialize it, the unit will automatically use the network settings of the

iOS device (iPhone/iPad/iPod touch) and try to connect to a wireless

LAN (unless the unit is already connected to a wired LAN).

If you have an iOS device, follow the procedure from Step 6 in the section “Sharing the iOS device setting” (p. 15).

If you plan to connect the unit wirelessly by another method, press RETURN to exit the current screen, and then proceed to one of

the sections below.

R-N303 XXXXXX

WAC

R-N303 (example)

Connecting using the Wi-Fi setting of the iOS

device (iPhone / iPad / iPod touch)

Share the Wi-Fi setting of the iOS

device (p. 15)

Connecting using WPS push button configuration

on the wireless router (or access point)

Use the WPS push button

configuration (p. 16)

Connecting with a wireless router (access point)

without WPS push button configuration

Set the network connection

manually (p. 16)

Connecting with the MusicCast CONTROLLER

app

See “Configuring MusicCast”

(p. 19) for details.

Connecting using the DHCP server function of the

router

You can connect to the network by

simply making a wired connection

(p. 13)

15 En

Connecting to a network

English

PREPARATION

■ Connecting without a wired router or wireless router (access point)

Note

When the unit is connected to the network with Wireless Direct, it cannot connect to any other wireless router (access point). To play

back contents from the Internet or to update the firmware of this unit over the network, connect the unit to a network with a wired router

or wireless router (access point).

Sharing the iOS device setting

You can easily setup a wireless connection by applying the

connection settings on iOS devices (iPhone/iPad/iPod

touch).

Before proceeding, confirm that your iOS device is

connected to a wireless router (access point).

Note

• If you perform the following procedure, all network settings will be

initialized.

• This configuration does not work if the security protocol of your

wireless router (access point) is WEP. In this case, use another

connection method.

1 Press SETUP.

2 Use the cursor keys ( / ) to select

“Network” and press ENTER.

Note

To return to the previous state, press RETURN.

3 Use the cursor keys ( / ) to select

“Connection” and press ENTER.

4 Use the cursor keys ( / ) to select

“Wireless” and press ENTER.

5 Use the cursor keys ( / ) to select “Share

Setting” and then press ENTER twice.

Note

When connected to a wired network, the front display will show

the messages “LAN CBL” and “Pls disconnect”. Unplug the

network cable from the unit, and press the ENTER key.

6 On the iOS device, select the unit as the

AirPlay speaker in the Wi-Fi screen.

7 Check that the “Network” field is set to your

preferred network, and then tap “Next”.

When the sharing process finishes, the unit is

automatically connected to the selected network

(access point).

When the setting finishes, verify whether the unit is

connected to a wireless network (p. 18).

Connecting wirelessly to a mobile device

(Wireless Direct)

Connect wirelessly with Wireless

Direct (p. 17)

MUTE

NOW PLAYING

RETURN

OPTION

VOLUME

CLEAR MODE DISPLAY

ENTER

HOME

SETUP

RETURN

SETUP

ENTER

Cursor keys

 / 

¡WPS

WIRELESS

The name of this unit

Example (iOS 10)

Tap here to start setup

The network currently

selected

16 En

Connecting to a network

Configuring with the router’s WPS

push button

You can easily set up a wireless connection with one push

of the WPS button.

Note

This configuration does not work if the security method of your

wireless router (access point) is WEP or WPA2-TKIP. In this

case, use another connection method.

1 Press SETUP.

2 Use the cursor keys ( / ) to select

“Network” and press ENTER.

Note

To return to the previous state, press RETURN.

3 Use the cursor keys ( / ) to select

“Connection” and press ENTER.

4 Use the cursor keys ( / ) to select

“Wireless” and press ENTER.

5 Press ENTER twice.

“Connecting” appears on the front display.

6 Push the WPS button on the wireless router

(access point).

When the connection process finishes, “Completed”

appears on the front display. When the setting

finishes, verify whether the unit is connected to a

wireless network (p. 18).

If “Completed” does not appear, repeat from Step 1 or

try another connection method.

7 To exit from the menu, press SETUP.

Set the wireless network connection

manually

Before performing the following procedure, check the

security method and security key on the wireless router

(access point).

1 Press SETUP.

2 Use the cursor keys ( / ) to select

“Network” and press ENTER.

Note

To return to the previous state, press RETURN.

3 Use the cursor keys ( / ) to select

“Connection” and press ENTER.

4 Use the cursor keys ( / ) to select

“Wireless” and press ENTER.

5 Use the cursor keys ( / ) to select

“ManualSetting” and press ENTER.

6 Use the cursor keys ( / ) to select “SSID”

and press ENTER.

About WPS

WPS (Wi-Fi Protected Setup) is a standard established by the

Wi-Fi Alliance, which allows easy establishment of a

wireless home network.

MUTE

NOW PLAYING

RETURN

OPTION

VOLUME

CLEAR MODE DISPLAY

ENTER

HOME

SETUP

RETURN

SETUP

ENTER

Cursor keys

 / 

¡WPS

WIRELESS

MUTE

NOW PLAYING

RETURN

OPTION

VOLUME

CLEAR MODE DISPLAY

ENTER

HOME

SETUP

ENTER

RETURN

SETUP

Cursor keys

¡SSID

MANUAL

SSID

La page charge ...

Yamaha RS700 Le manuel du propriétaire

Marque: Yamaha

Modèle: RS700

Catégorie: Tuners audio

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

italiano: Yamaha RS700 Manuale del proprietario
English: Yamaha RS700 Owner's manual
Deutsch: Yamaha RS700 Bedienungsanleitung
русский: Yamaha RS700 Инструкция по применению
Nederlands: Yamaha RS700 de handleiding
dansk: Yamaha RS700 Brugervejledning
svenska: Yamaha RS700 Bruksanvisning
Türkçe: Yamaha RS700 El kitabı
suomi: Yamaha RS700 Omistajan opas

Yamaha RS700 Le manuel du propriétaire

Yamaha RS700 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents