Whirlpool WETLV27HW Manuel utilisateur

W11028710A

W11105978A-SP

WASHER/DRYER

USE AND CARE GUIDE

Table of Contents

WASHER/DRYER SAFETY ...........................................2

WHAT’S NEW UNDER THE LID? .................................4

ACCESSORIES ..............................................................5

USING LESS WATER AND ENERGY ...........................5

CHECK YOUR VENT SYSTEM

FOR GOOD AIRFLOW .................................................6

CONTROL PANEL AND FEATURES ............................7

WASHER CYCLE GUIDE ..............................................8

DRYER CYCLE GUIDE ...............................................10

USING YOUR WASHER ..............................................11

USING YOUR DRYER .................................................14

ADDITIONAL FEATURES ............................................15

WASHER/DRYER MAINTENANCE ............................16

TROUBLESHOOTING .................................................20

WARRANTY ................................................................. 26

ASSISTANCE OR SERVICE ........................ Back Cover

Table des matières

SÉCURITÉ DE LA LAVEUSE/SÉCHEUSE .................27

QUOI DE NEUF SOUS LE COUVERCLE? .................30

ACCESSOIRES ............................................................31

RÉDUCTION DE LA CONSOMMATION D’EAU

ET D’ÉNERGIE. ...........................................................31

VÉRIFICATION D’UNE CIRCULATION

D’AIR ADÉQUATE POUR LE SYSTÈME

D’ÉVACUATION .......................................................... 32

TABLEAU DE COMMANDE

ET CARACTÉRISTIQUES ...........................................33

GUIDE DE PROGRAMMES DE LA LAVEUSE ...........35

GUIDE DE PROGRAMMES DE LA SÉCHEUSE ........37

UTILISATION DE LA LAVEUSE ..................................38

UTILISATION DE LA SÉCHEUSE ............................... 41

CARACTÉRISTIQUES SUPPLÉMENTAIRES.............43

ENTRETIEN DE LA LAVEUSE/SÉCHEUSE ...............44

DÉPANNAGE ...............................................................48

GARANTIE ...................................................................59

ASSISTANCE OU SERVICE ............ Couverture arrière

LAVEUSE/SÉCHEUSE

GUIDE D’UTILISATION

ET D’ENTRETIEN

Designed to use only HE High Efﬁciency detergents.

Conçue pour utiliser un détergent haute efﬁcacité seulement.

2

WASHER/DRYER SAFETY

3

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property

damage.

Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this

or any other appliance.

–

WHAT TO DO IF YOU SMELL GAS:

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use any phone in your building.

•

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

•

If you cannot reach your gas supplier, call the re department.

–

Installation and service must be performed by a qualied installer, service agency, or

the gas supplier.

•

Clear the room, building, or area of all occupants.

4

WHAT’S NEW UNDER THE LID?

Your new washer will operate differently than your past agitator-style washer.

Lid Lock

To allow for higher spin speeds, the lid will lock and the

Lid Lock light will turn on. When this light is lit, the lid is

locked and cannot be opened. When this light is blinking,

the washer is paused. When this light is off, the lid can

be opened. If you need to open the lid to add a garment

after this point, the lid will remain unlocked during the

entire agitation portion of the wash phase. The cycle will

automatically pause when the lid is opened, and the cycle

will resume once the lid is closed. The lid will lock before

the spin phase begins. If you need to pause or stop after

this point, you must press the START/PAUSE button and

wait for the lid to unlock. The lid will only unlock after

washer movement has stopped. Depending on when in

the cycle you try to pause, it may take several seconds

to several minutes for the lid to unlock. Press the START/

PAUSE button to resume the cycle.

Sensing

This washer will perform a series of spins to check for load

balance. During this time, a series of clicks and a whirring

noise signal that sensing technology is determining if there

is an off-balance load.

Sounds

At different stages of the wash cycle, you may hear sounds

and pauses that are different from those of your previous

washer. For example, you may hear a clicking and hum

at the beginning of the spin phase as the lid lock goes

through a self-test. There will be different kinds of humming

and whirring sounds as the agitator tests for load balance

or moves the load. And sometimes, you may hear nothing

at all as the washer determines the correct water level for

your load or allows time for clothes to soak.

IMPORTANT:

■ The lid must be closed before the washer basket lls with water and for the wash cycle to start. If the lid is open and lling stops,

close the lid and press the START/PAUSE button to complete the cycle.

■ Fabric Softener knob must be set to Yes when using fabric softener in the fabric softener dispenser. This ensures that fabric

softener is added at the correct time in the rinse phase and is evenly distributed.

Choosing the Right Detergent

Use only High Efciency detergents. The package will be

marked “HE” or “High Efciency.” Using non-HE detergent

will likely result in longer cycle times and reduced rinsing

performance. It may also result in component malfunction

and, over time, buildup of mold or mildew. HE detergents

should be low-sudsing and quick-dispersing to produce

the right amount of suds for the best performance. They

should hold soil in suspension so it is not redeposited

onto clean clothes. Not all detergents labeled as High

Efciency are identical in formulation and their ability to

reduce suds. For example, natural, organic, or homemade

HE detergents may generate a high level of suds. Always

follow the detergent manufacturer’s instructions to

determine the amount of detergent to use.

Use only High Efciency (HE) detergent.

Spray Rinse

Select cycles default to a spray rinse. During these cycles,

you will hear water enter the washer as the tub spins,

allowing the rinse water to penetrate clothes. Check

the “Cycle Guide” for details.

5

ACCESSORIES

This washer does not include inlet water hoses. See Installation

Instructions for installation accessories.

USING LESS WATER AND ENERGY

This washer is designed to use less water and energy, and

complies with all 2015 energy standards. Wash cycles with

controlled temperatures are designed to maintain cleaning

performance while using less water and energy compared to

older traditional washers. As a result, water levels will be lower,

and hot and warm wash temperatures may not be as warm as

you are used to.

Traditional washer

Reduced water washer

Accessories

Dryer vent lint brush

Drying rack

All-purpose appliance cleaner

Laundry supply storage cart

Enhance your new washer/dryer with the following genuine Whirlpool Accessories. For more information on options and ordering, call

1-800-901-2042 or visit us at: www.whirlpool.com/accessories. In Canada, call 1-800-807-6777 or visit us at www.whirlpoolparts.ca.

Fabric Softener Dispenser

This convenient fabric

softener dispenser connects

to the agitator and saves you

from manually adding fabric

softener during the rinse cycle.

Washer Dryer

6

CHECK YOUR VENT SYSTEM FOR GOOD AIRFLOW

Good airow

Along with heat, dryers require good airow to efciently

dry laundry. Proper venting will reduce your drying times and

improve your energy savings. See Installation Instructions.

The venting system attached to the dryer plays a big role

in good airow.

Service calls caused by improper venting are not covered

by the warranty and will be paid by the customer, regardless

of who installed the dryer.

Maintain good airow:

Good Better

■

Clean your lint screen before each load.

■

Replace plastic or foil vent material with 4" (102 mm)

diameter heavy, rigid vent material.

■

Use the shortest length of vent possible.

■

Use no more than four 90° elbows in a vent system;

each bend and curve reduces airow.

■

Remove lint and debris from the exhaust hood.

■

Remove lint from the entire length of the vent system at

least every 2 years. When cleaning is complete, be sure

to follow the Installation Instructions supplied with your

dryer for nal product check.

■

Clear away items from the front of the dryer.

4"

(102 mm)

Use Automatic cycles for better fabric care and energy savings

Use the Automatic Dry cycles to provide the most energy savings and enhanced fabric care from the dryer. During Automatic Dry

cycles, drying air temperature or moisture level are sensed in the load. This sensing occurs throughout the drying cycle, and the

dryer shuts off when the load reaches the selected dryness.

With Timed Drying, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to

overdrying. Use Timed Drying for the occasional damp load that needs a little more drying time or when using the drying rack.

7

3

4

1

CONTROL PANEL AND FEATURES

2

WASH CYCLE KNOB

Use the Wash Cycle knob to select available cycles on your

washer. Turn the knob to select a cycle for your laundry load.

See “Washer Cycle Guide” for detailed descriptions of cycles.

WASH TEMP

You may select a Wash Temperature based on the type of

fabric and soils being washed. Use the warmest wash water

safe for the fabric. Follow garment label instructions.

FABRIC SOFTENER

Set this knob to Yes when adding fabric softener to the

fabric softener dispenser.

START/PAUSE

Press the START/PAUSE button to start the washer.

WASH STATUS INDICATOR LIGHTS

The Cycle Status lights show the progress of a cycle.

At each stage of the process, you may notice sounds

or pauses that are different from your previous washer.

SENSE FILL

When the Start/Pause button is pressed, the washer will ll

and begin sensing to determine load size and balance.

Once sensing is complete, the washer will ll to the

appropriate level for the detected load size and then begin

the wash phase of the cycle.

NOTE: Sensing and wash phases will be paused by opening

the unlocked lid. Close the lid to resume the cycle. If the lid

is left open for more than 10 minutes, the washer will cancel

the cycle and pump out the water. The lid will lock after the

wash phase to begin the initial spinout and remain locked

for the remainder of the cycle.

1

2

3

4

5

Not all features and options are available on all models. Appearance may vary.

6

WASHER

WASH

The washer will ll to the correct water level based on the load

size. Certain cycles may agitate during the ll process to boost

cleaning. You will hear the agitator rotate, followed by a pause

lasting several seconds. When the wash cycle begins, you will

hear the agitator increase speed. The motor sounds may change

at different stages in the wash cycle while the washer performs

different wash actions.

RINSE

Certain cycles use a spray rinse, which adds water to the tub

while the basket spins. You may hear the motor turning on briey

(short hum) to move the basket while lling.

DRAIN/SPIN

The washer spins the load at increasing speeds for proper water

removal, based on the selected cycle.

DONE

Once the cycle is complete, this light will come on. Remove the

load promptly for best results.

LID LOCK

The Lid Lock feature allows for

higher spin speeds. When the Lid

Lock light is lit, the lid is locked and

cannot be opened without pausing

the cycle. When the light is off, the

lid can be opened.

To open the lid after it has been

locked, press START/PAUSE.

The lid will unlock once the

washer movement has stopped.

This may take several minutes if

the load was spinning at high speed.

Press START/PAUSE again to resume the cycle.

5

7

3

4

1 2

6

5

7

STANDARD VENT MODELS

LONG VENT MODELS

8

DRYER CYCLE KNOB

Use your Dryer Cycle knob to select available cycles on your

dryer. Turn the knob to select a cycle for your laundry load.

See “Dryer Cycle Guide” for detailed descriptions of cycles.

TIMED DRY

Will run the dryer for the specied time on the control.

Drying time and temperature will depend on your dryer

model.

NORMAL and DELICATE CYCLES

These cycles sense moisture in the load or air

temperature and shut off when the load reaches the

selected dryness level. They give the best drying in the

shortest time. Drying time will vary based on fabric type,

load size, and dryness setting.

AIR ONLY

This cycle will run the dryer without heat for the specied

time on the control.

6

DRYER

START BUTTON

The Start button is used to start the dryer. The end-of-cycle

signal produces an audible sound when the drying cycle is

nished. Promptly removing clothes at the end of the cycle

reduces wrinkling.

7

†Efcient use of resources, such as energy and water.

IMPORTANT: Do not presoak items in your washer by lifting the lid or stopping the cycle. Failure to follow this instruction can result

in property damage. If needed, presoak items in a small wash basin prior to loading the washer.

WASHER CYCLE GUIDE

Each cycle listing includes a performance chart rating its cleaning

power, gentleness on items, and resource efciency.

Not all cycles or options are available on all models. Refer

to the cycle control knob on your washer.

Wash temperatures are selected using the Wash Temp knob.

Cycles marked with “deep water wash” use a higher level

of water.

For best performance:

■ Choose the cycle that best ts the load being washed.

■ Decrease or increase the maximum target water

temperature for any cycle.

■ Do not leave the washer lid open unattended once

the washer has started to ll.

Items to wash: Cycle:

Load

Size:

Wash/Spin

Speed: Cycle Details:

Cottons, linens,

and mixed-garment

loads

Normal High and

Low/High

Use this cycle for normally soiled cottons and mixed-fabric loads.

No-iron fabrics,

cottons, permanent

press, linens,

synthetics

Casuals High and

Low/Low

Use this cycle to wash loads of no-iron fabrics such as sport

shirts, blouses, casual business clothes, permanent press,

and blends.

Machine-wash silks,

hand-washed fabrics

Delicates Low/Low Use this cycle to wash lightly soiled garments indicating “Machine

Washable Silks” or “Gentle” cycle on the care label. Place small

items in mesh garment bags before washing.

Cleaning

Gentleness

Efciency

†

Good

Best

Cleaning

Gentleness

Efciency

†

Good

Best

Cleaning

Gentleness

Efciency

†

Good

Best

9

Items to wash: Cycle:

Load

Size:

Wash/Spin

Speed: Cycle Details:

Sturdy fabrics,

colorfast items,

towels, jeans

Heavy Duty High/High Use this cycle for heavily soiled or sturdy items, or when using

bleach.

Colored cottons,

linens, casual

and mixed loads

Colors High/High Use this cycle for normally soiled colors and mixed-fabric loads.

Large items such

as sheets, sleeping

bags, small

comforters, jackets,

small washable rugs

Bulky

Items

Low/Low Use this cycle to wash large items such as jackets and small

comforters. The washer will ll with enough water to wet down

the load before the wash portion of the cycle begins, and uses

a higher water level than other cycles.

Lightly soiled

fabrics

Quick

Wash

High/High Use this cycle to quickly wash a small number of lightly soiled

items.

Hand-washed

garments or

dripping-wet items

Drain

& Spin

N/A N/A/

High

This cycle uses a spin to shorten drying times for heavy fabrics

or special-care items washed by hand. Use this cycle to drain

washer after cancelling a cycle or completing a cycle after a

power failure.

No clothes in

washer

Clean

Washer

with

affresh

®

N/A Low/

N/A

Use this cycle every 30 washes to keep the inside of your washer

fresh and clean. This cycle uses a higher water level. Use with

affresh

®

washer cleaner tablet or regular liquid chlorine bleach to

thoroughly clean the inside of your washer. This cycle should not

be interrupted. See “Washer Care.”

IMPORTANT: Do not place garments or other items in the

washer during the Clean Washer with affresh

®

cycle. Use this

cycle with an empty wash tub. Do not use thickened, easy-pour,

or no-splash bleach when running the Clean Washer with affresh

®

cycle as excess suds may occur. See “Washer Care” in “Washer/

Dryer Maintenance.”

WASHER CYCLE GUIDE (CONT.)

†Efcient use of resources, such as energy and water.

IMPORTANT: Do not presoak items in your washer by lifting the lid or stopping the cycle. Failure to follow this instruction can result

in property damage. If needed, presoak items in a small wash basin prior to loading the washer.

Cleaning

Gentleness

Efciency

†

Good

Best

Cleaning

Gentleness

Efciency

†

Good

Best

Cleaning

Gentleness

Efciency

†

Good

Best

Cleaning

Gentleness

Efciency

†

Good

Best

10

Not all cycles and settings are available on all models.

Both the Normal and Delicate cycles are automatic dry cycles.

They give the best drying in the shortest time. They sense

moisture in the load or air temperature and shut off when the

load reaches the selected dryness level. Drying time varies

based on fabric type, load size, and dryness setting.

Select either the Normal or Delicate cycle based on the

fabrics in your load. If you are unsure of the cycle to select

for a load, select the Delicate cycle (lower temperature) rather

than the Normal cycle (higher temperature).

WRINKLE SHIELD

™

option (long vent models)

This feature will run after your drying cycle is complete.

It periodically starts and stops the dryer, tumbling the load

without heat to help avoid wrinkling.

DRYER CYCLE GUIDE – AUTOMATIC DRY CYCLES

NOTE: If loads do not seem as dry as you would like, select Very Dry next time you dry a similar load. If loads seem drier than you

like, select Less Dry next time you dry a similar load.

DRYER CYCLE GUIDE – TIMED DRYING

Not all cycles and settings are available on all models.

Will run the dryer for the selected time.

Standard Vent Models Long Vent Models

NOTE: Government energy certications for this model were based on the Timed Dry cycle with the Maximum drying temperature

setting. The as-shipped defaults of Normal cycle, Less Dry, and the Wrinkle Shield

™

option (when applicable) were not used.

Items to dry: Cycle: Available Options: Cycle Details:

Corduroys, work clothes Normal None Medium to large loads of mixed fabrics and items.

Lingerie, blouses,

washable knit fabrics

Delicate None For gently drying delicate items.

Items to dry: Cycle: Temperature: Available Options: Cycle Details:

Rubber, plastic,

heat-sensitive fabrics

Air Only No Heat Time Adjustment For airing out, refreshing, and loosening up

laundry without heating.

Heavy, bulky, or

lightweight items

Timed Dry High Time Adjustment Completes drying if items are still damp.

11

■ Empty pockets. Loose change, buttons, or any small object

can pass under the agitator and become trapped, causing

unexpected sounds.

■ Sort items by recommended cycle, water temperature,

and colorfastness.

■ Separate heavily soiled items from lightly soiled.

■ Separate delicate items from sturdy fabrics.

■ Do not dry garments if stains remain after washing, because

heat can set stains into fabric.

■ Treat stains promptly.

■ Close zippers, fasten hooks, tie strings and sashes, and

remove non-washable trim and ornaments.

■ Mend rips and tears to avoid further damage to items

during washing.

Helpful Tips:

■ When washing waterproof or water-resistant items, load evenly.

■ Use mesh garment bags to help avoid tangling when washing

delicate or small items.

■ Turn knits inside out to avoid pilling. Separate lint-takers from

lint-givers. Synthetics, knits, and corduroy fabrics will pick up

lint from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care label instructions to

avoid damage to your garments.

1. Sort and prepare your laundry

USING YOUR WASHER

Add a measured amount of HE

detergent or single-dose laundry

packet into the basket.

If using Oxi-type boosters, color-safe

bleach, or fabric softener crystals, add

to the bottom of the washer basket before adding clothes.

IMPORTANT: Use only High Efciency detergents. The package

will be marked “HE” or “High Efciency.” Using non-HE

detergent will likely result in longer cycle times and reduced

rinsing performance. It may also result in component malfunction

and, over time, buildup of mold or mildew. HE detergents should

be low-sudsing and quick-dispersing to produce the right

amount of suds for the best performance. They should hold soil

in suspension so it is not redeposited onto clean clothes. Not all

detergents labeled as High Efciency are identical in formulation

and their ability to reduce suds. For example, natural, organic,

or homemade HE detergents may generate a high level of suds.

NOTE: Follow the manufacturer’s instructions to determine the

amount of laundry products to use.

2. Add laundry products

12

5. Add fabric softener to dispenser

Pour a measured amount of liquid fabric

softener into dispenser; always follow

manufacturer’s directions for correct amount

of fabric softener based on your load size.

Dilute liquid fabric softener by lling the dispenser with warm

water until liquid reaches the underside of the rim. See max ll

line arrows. Do not overll.

Adding Liquid Fabric Softener Manually to Wash Load

During the nal rinse, wait until the washer has completed lling

and press the START/PAUSE button to pause the washer. Lift

the lid and add the measured recommended amount of liquid

fabric softener. Do not allow liquid fabric softener to spill, splash,

drip, or run into the basket or on load. Do not use more than

the recommended amount. Close the lid and press the START/

PAUSE button again to start the washer.

Do not overll, dilute, or use more than 1 cup (236 mL).

Do not use color-safe bleach or Oxi products in the same

cycle with liquid chlorine bleach.

Load garments in loose heaps evenly around basket wall.

For best results, do not pack the load tightly. Do not wrap large

items such as sheets around the agitator; load them in loose

piles around the sides of the basket. Try mixing different-sized

items to reduce tangling.

3. Load laundry into washer

IMPORTANT: Do not tightly pack or force items into washer.

Items need to move freely for best cleaning and to reduce

wrinkling and tangling.

Turn cycle knob to choose your wash cycle. For more

information, see “Washer Cycle Guide.”

6. Select cycle

4. Add liquid chlorine bleach

to dispenser

MAX FILL

Liquid

Chlorine Bleach

13

7. Select wash temperature

Select the desired wash temperature by turning the Wash Temp

knob to the desired setting. All rinses are cold.

NOTE: Always read and follow fabric care label instructions

to avoid damage to your garments.

9. Press START/PAUSE to begin

wash cycle

Press the START/PAUSE button to start the wash cycle. When

the cycle has nished, the Done indicator will light. Promptly

remove garments after cycle has completed to avoid odor,

reduce wrinkling, and prevent rusting of metal hooks, zippers,

and snaps.

Adding garment(s)

If you need to open the lid to add one or two missed

garments: Press the START/PAUSE button. The lid will

unlock once the washer movement has stopped. This may

take several minutes if the load was spinning at high speed.

Add garments, close lid, and press the START/PAUSE button

again to restart the cycle.

NOTE: Washer will not ll with the lid open.

IMPORTANT: If lid is left open for more than 10 minutes, the

water will pump out automatically.

Manual Soak

If you would like to manually soak your garments at any

time during the wash portion of the cycle, press the START/

PAUSE button and leave the lid closed. Once your desired

soak time has elapsed, press the START/PAUSE button again

to continue the cycle. As long as the lid remains closed, your

soak time can be longer than 10 minutes. However, if the lid

is opened during the soak and remains open for more than

10 minutes, the water will pump out automatically.

Set this knob to Yes when adding fabric softener to the fabric

softener dispenser.

8. Select fabric softener (if desired)

Wash Temp Suggested Fabrics

Hot

Some cold water is added

to save energy. This will be

cooler than your hot water

heater setting.

Whites and pastels

Durable garments

Heavy soils

Warm

Some cold water will be

added, so this will be cooler

than what your previous

washer provided.

Bright colors

Moderate to light soils

Cool

Some warm water may

be added to assist in

soil removal and to help

dissolve detergents. Cool

is slightly warmer than cold.

Colors that bleed or fade

Light soils

Cold

This is the temperature

from your faucet. Warm

water may be added to

assist in soil removal and

to help dissolve detergents.

Dark colors that bleed or fade

Light soils

Tap Cold

This is the temperature

from your faucet.

Dark colors that bleed or fade

Light soils

14

USING YOUR DRYER

1. Clean the lint screen

Clean the lint screen before each load.

Pull the lint screen straight up. Roll lint off the screen with your

ngers. Push the lint screen rmly back into place.

Do not rinse or wash screen to remove lint. For additional

cleaning information, see “Cleaning the lint screen.”

2. Load the dryer

Place laundry in the dryer. Close the door.

NOTE: Your model may have a different door than the

one shown.

Do not tightly pack the dryer; clothes should be able to

tumble freely.

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the Important Safety Instructions before operating

this dryer.

Before using your dryer, wipe the dryer drum with a damp cloth

to remove dust from storing and shipping.

3. Select cycle

Select the desired cycle for your load. See “Dryer Cycle

Guide” for more information about each cycle.

Normal and Delicate Cycles

You can select a different dryness level, depending on your

load, by turning the knob to the desired dryness level.

Selecting Very Dry or Less Dry automatically adjusts the

dryness level at which the dryer will shut off. Once a dryness

level is set, it cannot be changed without stopping the cycle.

These automatic dry cycles give the best drying in the shortest

time. Drying time varies based on fabric type, load size, and

dryness setting.

NOTE: Very Dry removes more load moisture. Less Dry

removes less moisture and is used for loads you may want

to put on a hanger to complete drying.

15

4. Press START button to begin cycle

Press and hold the START button to begin the cycle.

Promptly remove garments after cycle has completed

to reduce wrinkling.

ADDITIONAL FEATURES

2. Align the two hooks on the front of the drying rack with

the holes in the dryer door opening and press down fully

into holes. Rest the rear support on the dryer back ledge.

USING THE DRYING RACK

To obtain a drying rack for your dryer, see the “Accessories”

section. Remove and discard any packing material before use.

Use the drying rack for items that you do not want to tumble

dry, such as sweaters and tennis shoes. When you use the

drying rack, the drum continues to turn, but the rack remains

stationary.

The drying rack is intended for use with the Timed Dry

cycles only. The drying rack cannot be used with Automatic

Dry cycles.

To use the drying rack:

IMPORTANT: Do not remove the lint screen.

1. Open dryer door.

3. Place wet items on top of the drying rack. Allow space

around items for air to circulate. The drying rack does

not move, but the drum will rotate. Make sure items do

not hang over the edges or between drying rack grille.

4. Close the door.

5. Select a Timed Dry/Air Only or Low Temperature cycle.

Items containing foam, rubber, or plastic must be dried

on a clothesline or by using the Air Only setting.

6. Start the dryer.

NOTE: Check the lint screen and remove any lint accumulated

from items dried on the drying rack after the cycle is nished.

16

WASHER CARE

Recommendations to Help Keep Your Washer Clean

and Performing at Its Best

1. Always use High Efciency detergents and follow the

detergent manufacturer’s instructions regarding the amount

of detergent to use. Never use more than the recommended

amount because that may increase the rate at which

detergent and soil residue accumulate inside your washer,

which in turn may result in undesirable odor.

2. Use warm and hot wash water settings sometimes (not

exclusively cold water washes), because they do a better

job of controlling the rate at which soils and detergent

accumulate.

3. Always leave the washer lid open between uses to help

dry out the washer and prevent the buildup of odor-causing

residue.

Cleaning Your Top-Loading Washer

Read these instructions completely before beginning the

routine cleaning processes recommended below. This Washer

Maintenance Procedure should be performed, at a minimum,

once per month or every 30 wash cycles, whichever occurs

sooner, to control the rate at which soils and detergent may

otherwise accumulate in your washer.

Cleaning the Inside of the Washer

To keep your washer odor-free, follow the usage instructions

provided above and use this recommended monthly cleaning

procedure:

Recommended Cycle for Cleaning the Washer

Refer to the “Cycle Guide” for the optimal cycle for cleaning

the inside of the washer. Use this cycle with affresh

®

Washer

Cleaner or liquid chlorine bleach as described below.

Begin procedure

affresh

®

Washer Cleaner Cycle procedure (Recommended

for Best Performance):

a. Open the washer lid and remove any clothing or items.

b. Use an affresh

®

Machine Cleaning Wipe or a soft, damp

cloth or sponge to clean the inside of the door.

c. Place an affesh

®

Washer Cleaner tablet in the bottom

of the washer basket.

d. Do not add any detergent or other chemical to the

washer when following this procedure.

e. Close the washer lid.

f. Select the Clean Washer with affresh

®

cycle.

g. Press and hold START/PAUSE to begin the cycle.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, press the START/PAUSE button once. After

the cycle has stopped, run a Quick Wash cycle to rinse cleaner

from washer.

Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Periodically inspect and replace inlet hoses

if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of replacement

on the label with a permanent marker.

WATER INLET HOSES

WASHER/DRYER MAINTENANCE

WASHER CARE (cont.)

Chlorine Bleach Procedure (Alternative):

a. Open the washer lid and remove any clothing

or items.

b. Add 1 cup (236 mL) of liquid chlorine bleach

to the bleach compartment.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage

over time.

c. Close the washer lid.

d. Do not add any detergent or other chemical to the

washer when following this procedure.

e. Select the Clean Washer with affresh

®

cycle.

f. Press and hold START/PAUSE to begin the cycle.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, press the START/PAUSE button once. After

the cycle has stopped, run a Quick Wash cycle to rinse

cleaner from washer.

Description of Clean Washer with affresh

®

Cycle Operation:

1. The Clean Washer with affresh

®

cycle will determine

whether clothing or other items are in the washer.

2. If no items are detected in the washer, it will proceed with

the cycle.

After the cycle is complete, leave the lid open to allow for

better ventilation and drying of the washer interior.

Cleaning the liquid fabric softener dispenser

(on some models)

1. Remove dispenser by grasping top with both hands

and squeezing, while pushing upward with thumbs.

2. Rinse dispenser under warm water or wipe the surfaces

with an affresh

®

Machine Cleaning Wipe or a damp cloth

and towel dry either before or after you run the Clean

Washer with affresh

®

cycle. Use an all-purpose surface

cleaner, if needed.

3. Replace the dispenser.

NOTE: To avoid damage to the washer or clothing,

do not wash clothes with the liquid fabric softener

dispenser removed.

Cleaning the bleach dispenser (on some models)

Wipe the inside of the bleach dispenser with an affresh

®

Machine Cleaning Wipe or a clean, damp cloth. Use an

all-purpose surface cleaner, if needed.

Cleaning the Outside of the Washer

Use an affresh

®

Machine Cleaning Wipe or a soft, damp cloth

or sponge to wipe away any spills. Use an affresh

®

Machine

Cleaning Wipe or only mild soaps or cleaners when cleaning

external washer surfaces.

IMPORTANT: To avoid damaging the washer’s nish,

do not use abrasive products.

17

Keep washer/dryer area clear and free from items that

would block the airow for proper washer/dryer operation.

This includes clearing piles of laundry in front of the washer/

dryer.

CLEANING THE DRYER INTERIOR

To clean dryer drum

1. Apply a liquid, nonammable household cleaner to the

stained area of the drum and rub with a soft cloth until

stain is removed.

2. Wipe drum thoroughly with a damp cloth.

3. Tumble a load of clean cloths or towels to dry the drum.

NOTE: Garments that contain loose dyes, such as denim

blue jeans or brightly colored cotton items, may discolor the

dryer interior. These stains are not harmful to your dryer and

will not stain future loads of clothes. Dry these items inside

out to avoid drum staining.

REMOVING ACCUMULATED LINT

From inside the dryer cabinet

Lint should be removed every 2 years, or more often,

depending on dryer usage. Cleaning should be done

by a qualied servicer.

From the exhaust vent

Lint should be removed every 2 years, or more often,

depending on dryer usage.

CLEANING THE WASHER/DRYER LOCATION

CLEANING THE LINT SCREEN

Every load cleaning

A screen blocked by lint can increase drying time.

The lint screen is located in the door opening of the dryer.

To clean:

1. Pull the lint screen straight up. Roll lint off the screen

with your ngers.

Do not rinse or wash the screen to remove lint. Wet lint

is hard to remove.

2. Push the lint screen rmly back into place.

IMPORTANT:

■

Do not run the dryer with the lint screen loose,

damaged, blocked, or missing. Doing so can cause

overheating and damage to both the dryer and fabrics.

■

If lint falls off the screen into the dryer during removal,

check the exhaust hood and remove the lint. See

“Venting Requirements” in the Installation Instructions.

As-needed cleaning

Laundry detergent and fabric softener residue can build

up on the lint screen. This buildup can cause longer drying

times for your clothes, or cause the dryer to stop before

your load is completely dry. The screen is probably clogged

if lint falls off while the screen is in the dryer.

Clean the lint screen with a nylon brush every 6 months,

or more frequently, if it becomes clogged due to a residue

buildup.

To wash:

1. Roll lint off the screen with your ngers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent.

Scrub lint screen with the brush to remove residue

buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel.

Reinstall screen in dryer.

18

CHANGING THE DRUM LIGHT (on some models)

1. Unplug dryer or disconnect power.

2. Open the dryer door. Locate the light bulb cover on the

back wall of the dryer. Using a Phillips-head screwdriver,

remove the screw located in the lower right-hand corner

of the cover. Remove the cover.

3. Turn bulb counterclockwise. Replace the bulb with

a 10-watt appliance bulb only. Replace the cover and

secure with the screw.

4. Plug into a grounded outlet or reconnect power.

VACATION, STORAGE, AND MOVING CARE

Non-Use or Storage Care

Operate your washer/dryer only when you are at home.

If you will be on vacation or not using your washer/dryer

for an extended period of time, you should:

1. Unplug washer/dryer or disconnect power.

2. Turn off water supply to washer, to avoid ooding due

to water pressure surge.

3. For gas dryers only: Close shut-off valve to gas supply line.

4. Clean lint screen. See “Cleaning the Lint Screen”.

Moving Care

For power supply cord-connected washer/dryers:

1. Unplug the power supply cord.

2. Make sure leveling legs are secure in washer/dryer base.

3. Continue with “For all washer/dryers” in next column.

For direct-wired washer/dryers:

1. Turn off power at fuse or breaker box.

2. Disconnect wiring.

3. Make sure leveling legs are secure in washer/dryer base.

4. Continue with “For all washer/dryers” below.

For gas washer/dryers:

1. Unplug or disconnect power to washer/dryer.

2. Close shut-off valve in gas supply line.

3. Disconnect gas supply line pipe and remove ttings

attached to dryer pipe.

4. Cap the open fuel supply line.

5. Make sure leveling legs are secure in washer/dryer base.

6. Continue with “For all washer/dryers” below.

For all washer/dryers:

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. If washer/dryer will be moved during freezing weather,

follow “Winter Storage Care” directions before moving.

3. Disconnect drain hose from drain system and drain any

remaining water into a pan or bucket. Disconnect drain

hose from back of washer.

4. Place inlet hoses and drain hose inside washer basket.

5. Drape power cord over edge and into washer basket.

6. Place packing tray from original shipping materials

back inside washer/dryer. If you do not have packing

tray, place heavy blankets or towels into basket opening.

Close lids/doors and place tape over lids/doors and

down front of washer/dryer. Keep lids/doors taped

until washer/dryer is placed in new location.

VACATION, STORAGE, AND MOVING CARE (cont.)

19

2. Plug in washer/dryer or reconnect power.

3. Run washer through Bulky Items cycle to clean washer

and remove antifreeze, if used. Use only HE High Efciency

detergent. Use half the manufacturer’s recommended

amount of detergent for a medium-size load.

In the U.S.A.

In Canada

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer/dryer

where it will not freeze. Because some water may stay in

hoses, freezing can damage washer/dryer. If storing or moving

during freezing weather, winterize your washer/dryer.

To winterize washer/dryer:

1. Shut off both water faucets, disconnect and drain water

inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run

washer on Quick Wash cycle for about 30 seconds to mix

antifreeze and remaining water.

3. Unplug washer/dryer or disconnect power.

REINSTALLING/USING WASHER/DRYER AGAIN

To reinstall washer/dryer after non-use, vacation, moving,

or winter storage:

1. Refer to Installation Instructions to locate, level, and

connect washer/dryer.

2. Before using again, run washer/dryer through the following

recommended procedure:

To use washer/dryer again:

1. Flush water pipes and hoses. Reconnect water inlet hoses.

Turn on both water faucets.

(continued in next column)

In the U.S.A. and Canada

20

TROUBLESHOOTING – WASHER

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help –

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

If you experience Possible Causes Solution

Vibration or Off-Balance

Check the following for

proper installation or see

“Using Your Washer”

section.

Feet may not be in contact with

the oor and locked.

Front and rear feet must be in rm contact with oor, and washer/dryer

must be level to operate properly. Jam nuts must be tight against the

bottom of the cabinet.

Washer/dryer may not be level. Check oor for exing or sagging. If ooring is uneven, a 3/4" (19 mm)

piece of plywood under your washer/dryer will reduce sound.

See “Level the Washer/Dryer” in Installation Instructions.

Load could be unbalanced. Load dry items in loose heaps evenly around basket wall. Adding

wet items to washer or adding more water to basket could unbalance

washer.

Do not tightly pack. Avoid washing single items.

Use Bulky Items cycle for oversized, non-absorbent items such as

jackets and small comforters. See “Cycle Guide.”

See “Washer Cycle Guide” and “Using Your Washer” in this Use and

Care Guide.

Noises

Clicking or metallic

noises

Objects caught in washer drain

system.

Empty pockets before washing. Loose items such as coins could fall

between basket and tub or may block pump. It may be necessary to

call for service to remove items.

It is normal to hear metal items on clothing such as metal snaps,

buckles, or zippers touch against the stainless steel basket.

Gurgling or humming Washer may be draining water. It is normal to hear the pump making a continuous humming

sound with periodic gurgling or surging as nal amounts of water

are removed during the Drain & Spin cycle.

Humming Load sensing may be occurring. You may hear the hum of the sensing spins after you have started the

washer. This is normal.

Whirring Basket deceleration may be

occurring.

You may hear the whirring sound of the basket decelerating. This is

normal.

Water Leaks

Check the following for

proper installation:

Washer not level. Water may splash off basket if washer is not level. Check that load is

not unbalanced or tightly packed.

Fill hoses not attached tightly. Tighten ll-hose connection.

Fill hose washers. Make sure all four ll hose at washers are properly seated.

Drain hose connection. Pull drain hose from washer cabinet and properly secure it to

drainpipe or laundry tub.

Do not place tape over drain opening.

Check household plumbing for

leaks or clogged sink or drain.

Water can back up out of a clogged sink or drainpipe. Check all

household plumbing for leaks (laundry tubs, drain pipe, water pipes,

and faucets.)

Washer not loaded as

recommended.

Improper loading can cause basket to be out of alignment and

cause water to splash off tub. See “Using Your Washer” for loading

instructions.

Washer not performing as expected

Not enough water

in washer

Load not completely covered

in water.

Use Bulky Items cycle for higher water ll. See “Cycle Guide” to match

your load with the best cycle.

Run Clean Washer with affresh

®

cycle to optimize the water level and

wash performance due to soil buildup in washer basket.

Washer won’t run or ll,

washer stops working,

or wash light remains

on (indicating that the

washer was unable to ll

appropriately)

Check for proper water supply. Both hoses must be attached and have water owing to inlet valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water ow.

La page est en cours de chargement...

Whirlpool WETLV27HW Manuel utilisateur

Ce manuel convient également à

Whirlpool WETLV27HW Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents