GE GFD48ESPKDG Manuel utilisateur

DRYERS

SAFETY INSTRUCTIONS .........4

USING THE DRYER

Controls ............................ 6

Getting Started ...................... 7

Loading ............................. 11

Features .............................12

CARE AND CLEANING ..........13

INSTALLATION

INSTRUCTIONS

..................14

Reversing the door swing ............. 33

Stacking .............................38

TROUBLESHOOTING TIPS ..... 42

CONSUMER SUPPORT

Warranty ........................... 46

Consumer Support ................... 48

GFD49

GFD48

GFDR485

GFDR480

GHDS365

GHDS360

GFDR275

GFDR270

GFDS265

GFDS260

OWNER’S MANUAL &

INSTALLATION

INSTRUCTIONS

Write the model and serial

numbers here:

Model # _________________

Serial # _________________

They are on the label on the front

of the dryer behind the door.

49-90519-3 09-16 GEA

ENGLISH/FRANÇAIS/

ESPAÑOL

GE is a trademark of the General Electric Company. Manufactured under trademark license.

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Register your GE appliance now online. Helpful websites and phone numbers are available in the

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

2

3

Notes.

GEAppliances.com

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, explosion, electric shock, or injury to persons when using your appliance, follow basic

precautions, including the following:



Read all instructions before using the appliance.



DO NOT dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning

solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.

 DO NOT place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical

reaction that could cause a load to catch fire. To reduce the risk of fire due to contaminated loads, the final part of the tumble

dryer cycle occurs without heat (cool down period). Avoid stopping a tumble dryer before the end of the drying cycle unless all

items are quickly removed and spread out so that the heat is dissipated.



DO NOT allow children to play on or in this appliance. Close supervision of children is necessary when this appliance is

used near children.



Before the appliance is removed from service or discarded, remove the door to the drying compartment.



DO NOT reach into the appliance if the drum is moving.



DO NOT install or store this appliance where it will be exposed to the weather.



DO NOT tamper with controls.

 DO NOT repair or replace any part of this appliance or attempt any servicing unless specifically recommended in the

user-maintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.



DO NOT use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric

softener or product.



DO NOT dry articles containing foam rubber or similarly textured rubber-like materials.



Clean lint screen before or after each load.



DO NOT operate the dryer without the lint filter in place.



DO NOT store combustible materials, gasoline or other flammable liquids near the dryer.

Keep area around the exhaust

opening and adjacent surrounding areas free from the accumulation of lint, dust and dirt.



The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.



Unplug the appliance or turn off the circuit breaker before servicing. Pressing the Power or Start/Pause button DOES NOT

disconnect power.



DO NOT operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts,

including a damaged cord or plug.



DO NOT spray any type of aerosol into, on or near dryer at any time. DO NOT use any type of spray cleaner when cleaning dryer

interior. Hazardous fumes or electrical shock could occur

.



See “ELECTRICAL CONNECTION” located in the Installation Instructions for grounding instructions.

SAVE THESE INSTRUCTIONS

WARNING

4

GEAppliances.com

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

- DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• DO NOT try to light any appliance.

• DO NOT touch any electrical switch; DO NOT use any phone in your building.

• Clear the room, building, or area of any occupants.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or the gas

supplier.

SAVE THESE INSTRUCTIONS

5

State of California Proposition 65 Warnings

WARNING

This product contains one or more chemicals known to the State of California to cause cancer, and birth defects

or other reproductive harm.

Gas appliances can cause low-level exposure to some of these substances, including benzene, carbon monoxide, formaldehyde, and

soot, caused primarily by the incomplete combustion of natural gas or LP fuels. Exposure to these substances can be minimized by

properly venting the dryer to the outdoors.

- Fire or Explosion Hazard

WARNING

ADDITIONAL GAS DRYER WARNINGS

About the dryer control panel.

To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS

before operating this appliance.

Throughout this manual, features and appearance may vary from your model.

6

Models:

GFDR485

GFDR480

GHDS365

GHDS360

Models:

GFDR275

GFDR270

1 8 3 7

65416

14

15

2

9 10 11 12

17 13 18 19

1 8 3 7

65416

15

2

9 10 11 12

17 13 18 19

Models:

GFDS265

GFDS260

1 8 3 7

65416

15

2

9 10 11 12

17 13 18 19

WARNING

Models:

GFD49

GFD48

Delay Dry

Add Time

Damp

Extra Dry

Dry

Less Dry

More Dry

Extra

Low

No Hea t

Lo w

High

Medium

Tumble

S

t

eam

Detangle

Ref resh

Delay

Clean

Filt er

My

Cycle

Hold 3 Secs to Store Cycle

Estima

t

ed Time

R

emaining

My Cycle

Status

Steam

Dry

Damp

Cool

Done

Hold 3 Secs t o Cancel

1 8 3 13

65416

15

2

10 11 12

7 18 19

9

14

Power

Press to “wake up” the display. If the display is active, press to turn the dryer off.

NOTE: Pressing Power does not disconnect the appliance from the power supply.

1

Control settings.

GEAppliances.com

7

2

Start/Pause

Press to start a dry cycle. If the dryer is running,

press it once and it will pause the dryer. Press it

again to resume the dry cycle.

Getting Started

1

Press the

Power

button.

2

Select a dry cycle. (Defaults are set

for each cycle. These default

settings can be changed. See

Control settings for more

information.)

3

Press the Start/Pause button.

If the screen is dark, a press

of the Power button will

“wake up” the display.

Normal/Mixed Loads

For loads consisting of cottons and poly-blends.

Cottons

For cottons and most linens. NOTE: Energy Star

®

models are tested on Cottons with default settings.

Bulky/Bedding or

Bulky Items

For large coats, bed spreads, mattress covers, sleeping bags, blankets, comforters, jackets, small rugs,

and similar large and bulky items.

Active Wear

Clothing worn for active sports exercise and some casual wear. Fabrics include new technology

finishes and stretch fibers such as Spandex. Also for clothing labeled Easy Care or Perma Press: For

wrinkle-free and permanent press items.

Delicates

For lingerie and special-care fabrics.

Speed Dry or

Quick Dry

For small loads that are needed in a hurry, such as sports or school uniforms. Can also be used if the

previous cycle left some items damp, such as collars or waistbands.

Towels/Sheets

Use for towels OR sheets. It is not recommended to mix towels and sheets in the same load.

Sanitize

Reduces certain types of bacteria by 99.8%, including: Staphylococcus aureus, Pseudomonas

aeruginosa, and Klebsiella pneumoniae. The antibacterial process occurs when high heat is used

during a portion of this drying cycle.

Steam Dewrinkle

Full Loads

Provides 20 minutes of steam drying to assist with dewrinkling clothes.

Ideal for loads left in dryer

for an extended time.

Warm Up

Provides 10 minutes of warming time to warm up clothes.

Air Fluff

Provides 10 minutes of tumbling time without heat.

Time Dry

Use to set your own dry time. Time Dry is also recommended for small loads. To use:

1. Turn dry cycle dial to Time Dry.

2. Increase the drying time by pressing the Add Time button.

Note: This button only increases the time. When max time is reached, pressing the button again

will reset the counter to the lowest setting.

3. Select the Temp.

4. Close the door.

5. Press Start/Pause.

Dry Cycles

The dry cycle controls the length and tumble speed of the drying process. The chart below will help you match the dry

setting with the loads.

3

Control settings.

Add Time

Press to add time to the Steam Dewrinkle,

Warm Up, Air Fluff or Time Dry cycles in 10

minute increments.

4

Temp

You can change the temperature of your dry

cycle.

5

High For regular to heavy cottons.

Medium For synthetics, blends and items labeled Permanent Press.

Low For delicates, synthetics and items labeled Tumble Dry Low.

Extra Low For lingerie and special-care fabrics.

No Heat This option may only be used with Air Fluff, in which items are tumbled without

heat.

Level

The sensor continuously monitors the amount of

moisture in the load. When the moisture in your

clothes reaches your selected dry level, the dryer

will stop.

NOTE: Sensor dry Level only works with

Cottons, Normal, Active Wear, Delicates,

Speed Dry, Bulky, Towels/Sheets, Sanitize

and Steam Dewrinkle cycles.

6

Extra Dry

(on some models)

Use for heavy-duty fabrics or items that should be very dry, such as towels.

More Dry Use for heavy or mixed type of fabrics.

Dry Use for normal dryness level suitable for most loads. This is the preferred cycle for energy

saving.

Less Dry

Use for lighter fabric (ideal for ironing).

Damp For leaving items partially damp.

7

My Cycle

Set up your favorite combination of settings

and save them here for one touch recall. These

custom settings can be set while a cycle is in

progress.

To store a My Cycle combination of settings:

1. Select your drying cycle.

2. Change Temp and Level settings to fit your

needs.

3. Select any drying options you want.

4. Press and hold the My Cycle button for 3

seconds to store your selection. A beep will

sound and the button will light up.

To recall your stored My Cycle combination:

Press the MY CYCLE button before drying a

load.

To change your stored My Cycle combination:

Repeat steps 1–4.

8

My Cycle

Hold 3 Secs to Store Cycle

(Depending

on model)

GEAppliances.com

Steam Refresh Cycle

For slightly wrinkled dry garments. Significantly

reduces wrinkles on up to 5 garments. After the

Steam Refresh Cycle, the unit will beep and display

“0:00.” If the unit is not turned off or if the door is

not opened, the dryer will continue to tumble for

30 minutes. At the end of 30 minutes, it will display

“0:00” and the cycle will be complete.

NOTE: A single extremely light fabric item may need

to have an additional item included to achieve

optimum results.

8

Detangle (on some models)

Activates alternating forward and reverse tumbling

to reduce tangling, dry more evenly, and improve

drying times. Typical loads such as bed and bath

mixed loads, where sheets, towels and pillow cases

are laundered together, benefit from this capability.

When the dryer reverses direction, there will be a

slight pause and sound change. This is normal.

NOTE: Detangle is selected by default for Towels/

Sheets and Bulky/Bedding cycles.

9

eDry

Reduces the total energy consumption of specific

dryer cycles by adjusting certain heat settings.

NOTE: Cycle times will change when e-Dry is

selected.

This cycle can be used with Cottons, Normal, Active

Wear, Delicates, Speed Dry, Bulky, Towels-Sheets,

Sanitize and Steam Dewrinkle.

10

Extended Tumble

Minimizes wrinkles by adding approximately 60

minutes of no-heat tumbling after clothes are

dry. The beeper will sound every five minutes as a

reminder to remove the clothes.

The estimated time remaining display will show

“0:00”.

The extended tumble time does not get added to

the cycle time on the display.

11

Damp Alert

This option causes the dryer to beep when clothes

have dried to a damp level. Remove items that you

wish to hang dry. The Damp Alert will only beep

when this option is selected, and the dryer will

continue to dry.

Removing clothes and hanging them when they are

damp can reduce the need to iron some items.

12

Delay Dry

Use to delay the start of your dryer.

1. Choose your dry cycle and any options.

2. Press Delay Dry. You can change the delay time

in 1 hour increments, using the Delay Dry button.

3. Press the Start/Pause button to start the

countdown.

NOTE: If the door is opened while the dryer is in

Delay Dry, the countdown time will not restart

unless the door is closed and Start/Pause button

has been pressed again.

13

Delay Dry

(Depending

on model)

Control settings.

Light (on some models)

Press the button to turn on the light in the

dryer.

Press the button again to turn the light off.

This only controls the light when the door is

shut.

NOTE: The light will turn off by itself after one

minute when the door is shut.

14

Lock Control

You can lock the controls to prevent any

selections from being made. Or you can lock

or unlock the controls after you have started a

cycle.

Children cannot accidentally start the dryer by

touching buttons with this option selected.

To lock the dryer, press and hold the Lock

Control button for 3 seconds.

To unlock the dryer controls, press and hold the

Lock Control button for 3 seconds.

A sound is made to indicate the lock/unlock

status.

The indicator light above the button will

illuminate when the controls are locked.

NOTE: The Power button can still be used when

the machine is locked.

15

16

17

eMonitor (on some models)

The eMonitor lights display the relative energy

use of your selected cycle and options. They are

provided as an energy guide and range from

Good (1 light) to Better (5 lights). Cycle (time),

dryness level, temperature, and additional

tumble options can increase or decrease your

energy efficiency. Some cycles will not provide

a display.

18

Clean Filter Message

This message represents only a reminder and

does not always appear when the filter needs

cleaning. The filter should be cleaned after every

drying cycle is complete.

This message will disappear after the Start/

Pause button is pressed. Even though you may

have already cleaned the filter (before or after the

Power button has been pressed), the “Clean Filter”

message will still be displayed until the Start/

Pause button is activated.

19

Display

Displays the approximate time remaining until

the end of the cycle.

As the cycle begins, you will see an initial

approximate total cycle time in the display.

Then lights will “race” in the display. This

means the dryer is continuously monitoring

the amount of moisture in the load. The lights

will continue until the dryer senses a low level

of moisture in the load. At that point, the dryer

will calculate and display the approximate time

remaining.

10

Volume

This button has two functions:

 To change the loudness of the end of cycle

signal, press the button as many times as

needed to reach the desired volume. There are

four sound levels including OFF.

 To turn the button sounds ON/OFF, press

and hold the button for 3 seconds (on some

models).

Loading.

GEAppliances.com

Fabric Care Labels

Below are fabric care label “symbols” that affect the clothing you will be laundering.

Tumble

dry

Dry

Normal

Permanent Press/

wrinkle resistant

Gentle/

delicate

Do not tumble dry

Do not dry

(used with

do not wash)

Heat

setting

High

Medium

Low

No heat/air

Special

instructions

Line dry/

hang to dry

Drip dry

Dry flat

In the shade

Dry Labels

As a general rule, if clothes are sorted properly for the washer,

they are sorted properly for the dryer. Try also to sort items

according to size. For example, do not dry a sheet with socks or

other small items.

Do not add fabric softener sheets once the load has become

warm. They may cause fabric softener stains. Bounce

®

Fabric

Conditioner Dryer Sheets have been approved for use in this

dryer when used in accordance with the manufacturer’s

instructions.

Do not overload. This wastes energy and causes wrinkling.

Sorting and Loading Hints

Always follow the fabric manufacturer’s care label when laundering.

11

• Keep flammable materials and vapors, such as gasoline,

away from dryer.

• DO NOT dry anything that has ever had anything flammable

on it (even after washing).

• No washer can completely remove oil.

• DO NOT dry anything that has ever had any type of oil on it

(including cooking oils).

• Items containing foam, rubber, or plastic must be dried on a

clothesline.

• Failure to do so can result in death, explosion, or fire.

- Fire Hazard

WARNING

About dryer features.

Drying Rack (on some models)

A handy drying rack may be used for drying

delicate items such as washable sweaters.

Place items flat on the drying rack and block

such items as wool sweaters and delicate

fabrics. Dry with low heat.

To install the drying rack, extend the drying

rack into the dryer drum. Rest the front two

legs on the front angled ledge and then rest

the rear two legs on the rear angled edge.

NOTES:

 The drying rack is designed for use with

the Time Dry cycles. Use with sensor

cycles may result in damp items or

extended cycle times.

 Do not use this drying rack when there

are other clothes in the dryer, that are not

placed on the rack.

 The drying rack, WE01X22274, is available

as an accessory. Order on-line at

GEApplianceParts.com, 24 hours a day or

by phone at 877.959.8688 during normal

business hours.

Rest rear legs on

rear angled ledge

Rest front legs on

front angled ledge

12

Care and Cleaning of the Dryer.

GEAppliances.com

The Exterior: Wipe or dust any spills or

washing compounds with a damp cloth.

Dryer control panel and finishes may be

damaged by some laundry pretreatment

soil and stain remover products. Apply these

products away from the dryer. The fabric

may then be washed and dried normally.

Damage to your dryer caused by these

products is not covered by your warranty.

The Lint Filter: Clean the lint filter before

each use.

Pull out the lint filter. Moisten your fingers

and remove the captured lint. Once clean,

slide the filter back into position. Have a

qualified technician vacuum the lint from the

dryer once a year.

NEVER OPERATE THE DRYER WITHOUT ITS

FILTER IN PLACE.

Stainless Steel: To clean stainless steel

surfaces use a damp cloth with a mild, non-

abrasive cleaner suitable for stainless steel

surfaces. Remove the cleaner residue and

then dry with a clean cloth.

The stainless steel used to make the dryer

drum provides the highest reliability available

in a GE Appliances dryer. If the dryer drum

should be scratched or dented during normal

use, the drum will not rust or corrode. These

surface blemishes will not affect the function

or durability of the drum.

Dryer Interior and Duct: The interior of

the appliance and exhaust duct should be

cleaned once a year by qualified service

personnel.

The Exhaust Duct: Inspect and clean the

exhaust ducting at least once a year to

prevent clogging. A partially clogged exhaust

can lengthen the drying time.

The Exhaust Hood: Check with a mirror that

the inside flaps of the hood move freely when

operating. Make sure that there is no wildlife

(birds, insects, etc.) nesting inside the duct or

hood.

13

NOTE: The drum lamp is not consumer

replaceable on models where there is a

domed cover over an LED bulb. If this light

should ever stop working, call for service.

For models that have a flat cover over the

bulb secured by a screw:

Before replacing the light bulb, be sure to

unplug the dryer power cord or disconnect

the dryer at the household distribution panel

by removing the fuse or switching off the

circuit breaker. Reach above dryer opening

from inside the drum to locate the light.

Remove the screw and the plastic cover to

access the bulb. Replace with the appropriate

bulb and then reaffix the cover and screw.

Order replacement bulb WE4M305 on-line

at GEApplianceParts.com, by phone at

877.959.8688 during normal business hours,

or purchase appliance bulb 7C7 from your

local retailer.

The drum lamp turns on automatically when

the dryer door is open. On some models, it

can also be activated from the control panel.

Drum Lamp

(consumer replaceable on some models)

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these instructions for local

electrical inspector’s use.

•

IMPORTANT – Observe all governing codes and

ordinances.

•

Install the clothes dryer according to the manufacturer’s

instructions and local codes.

•

Note to Installer – Be sure to leave these instructions

with the Consumer.

•

Note to Consumer – Keep these instructions for future

reference.

•

Clothes dryer installation must be performed by a

qualified installer.

•

This dryer must be exhausted to the outdoors.

•

Before the old dryer is removed from service or

discarded, remove the dryer door.

•

Service information and the wiring diagram are located

in the control console.

•

Do not allow children on or in the appliance. Close

supervision of children is necessary when the appliance

is used near children.

•

Proper installation is the responsibility of the installer.

•

Product failure due to improper installation is not

covered under the Warranty

.

• Install the dryer where the temperature is above 50°F

for satisfactory operation of the dryer control system.

• Remove and discard existing plastic or metal foil duct

and replace with UL-listed duct.

Questions? Call GE Appliances at 800.GE.CARES (800.432.2737) or visit our Web site at: GEAppliances.com

In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca

- Fire Hazard

WARNING

• Clothes dryer installation must be performed by a

qualified installer.

•

Install the clothes dryer according to these

instructions and local codes.

•

DO NOT install a clothes dryer with flexible plastic

venting materials. If flexible metal (semi-rigid or

foil-type) duct is installed, it must be UL-listed and

installed in accordance with the instructions found

in “Connecting the Dryer to House Vent” later in

this manual. Flexible venting materials are known

to collapse, be easily crushed and trap lint. These

conditions will obstruct dryer airflow and increase

the risk of fire.

•

DO NOT install or store this appliance in any

location where it could be exposed to water or

weather.

•

To reduce the risk of severe injury or death, follow

all installation instructions.

•

Save these instructions. (Installers: Be sure to leave

these instructions with the customer.)

Installation Dryers

Instructions

14

IN THE COMMONWEALTH OF

MASSACHUSETTS, THE FOLLOWING

INSTALLATION INSTRUCTIONS APPLY:

• Installation must be performed by a qualified

or licensed contractor, plumber, or gasfitter

qualified or licensed by the State.

•

If using a ball valve, it shall be a T-handle type.

•

A flexible gas connector, when used, must not

exceed 3 feet.

FOR GAS DRYERS ONLY

Installation Instructions

Tilt the dryer sideways and remove the foam shipping pads by pulling

at the sides and breaking them away from the dryer legs. Be sure to

remove all of the foam pieces around the legs.

Remove the bag containing the literature.

UNPACKING YOUR DRYER

DRYER

DIMENSIONS

Front View

*NOTE:

With Legs: 40 1/2” (102.5 cm) - (3/4” (1.9 cm) adjustability)

With Built-In Pedestal

™

: 46” (117 cm) - (3/4” (1.9 cm) adjustability)

With Optional Pedestal (GFXP1308): 52” (132.1 cm) - (3/4” (1.9 cm) adjustability)

Stacked: 78 1/4” (198.8 cm) - Not applicable for models with Built-In Pedestal

™

39”*

(99cm)

28”

(71.12cm)

46”*

(117cm)

39”*

(99cm)

Side View

32 7/8” (83.5cm)

54 3/8”* (138.1cm)

46”*

(117cm)

Built-In

Pedestal™

models

only

POWER CORDS:

GE Appliances strongly recommends the use of factory

specified parts. Select the power cord to fit your installation

requirements.

GE Appliances strongly recommends the use of factory

specified parts. These hoses are manufactured and tested to

meet GE Appliances specifications.

GE Appliances strongly recommends the use of new water

supply hoses. Hoses degrade over time and need to be

replaced every 5 years to reduce the risk of hose failures and

water damage.

Parts and Accessories

Order on-line at GEApplianceParts.com, 24 hours a day or

by phone at 877.959.8688 during normal business hours.

STEAM WATER HOSES

15

Part Number Type Length Amperage

WX9X2 3-Prong 4 Feet 30

WX9X3 3-Prong 5 Feet 30

WX9X4 3-Prong 6 Feet 30

WX9X18 4-Prong 4 Feet 30

WX9X19 4-Prong 5 Feet 30

WX9X20 4-Prong 6 Feet 30

ACCESSORIES:

Order on-line at GEApplianceParts.com, 24 hours a day or

by phone at 877.959.8688 during normal business hours.

Part Number Accessory

GFP1328SK

28” width White Pedestal

GFP1328PK

28” width Color Matched Pedestal

GEFLSTACK Stacking Kit for Dryer over Washer

PM08X10085

Flexible Metal Dryer Transition Duct

WE01X22274

Clothes Dryer Shoe Rack

Part Number

Accessory

WE25X20060

Complete Kit (hoses, Y-adapter washers)

OR

WH41X10356

Long Hose and

WH41X10357 Short Hose

Installation Instructions

MOBILE OR MANUFACTURED HOME

INSTALLATION

16

• Installation MUST conform to the

MANUFACTURED HOME CONSTRUCTION AND

SAFETY STANDARD, TITLE 24, PART 3280 or

STANDARD FOR MOBILE HOMES CAN/CSA-Z240

MH, or, when such standards are not applicable,

with AMERICAN NATIONAL STANDARD FOR

MOBILE HOME, ANSI/NFPA NO. 501B.

•

The dryer MUST be vented to the outdoors.

•

The exhaust vent MUST be securely fastened to

a non-combustible portion of the mobile home.

•

The vent MUST NOT be terminated beneath a

mobile or manufactured home.

•

The vent duct material MUST BE METAL.

•

KIT 14-D346-33 MUST be used to attach the dryer

securely to the structure.

•

The vent MUST NOT be connected to any other

duct, vent or chimney.

•

DO NOT use sheet metal screws or other

fastening devices which extend into the interior

of the exhaust vent.

•

Provide an opening with a free area of at least

25 square inches for introduction of outside air

into the dryer room.

•

See the sections for electrical connection

information.

REQUIREMENTS FOR ALCOVE OR CLOSET

INSTALLATION

- Explosion Hazard

WARNING

Keep flammable materials and vapors, such as gasoline,

away from dryer.

Place dryer at least 18” (46 cm) above the floor for a

garage installation.

Failure to do so can result in death, explosion, or fire.

• The dryer MUST be vented to the outdoors.

• Minimum clearance between dryer cabinet and

adjacent walls or other surfaces is:

0” either side

1” front and rear

1” top

•

Consideration must be given to provide adequate

clearance for installation and service.

•

Closet doors must be louvered or otherwise

ventilated and have at least 60 square inches of

open area. If the closet contains both a washer

and a dryer, doors must contain a minimum of

120 square inches of open area.

NOTE: WHEN THE EXHAUST DUCT IS LOCATED AT

THE REAR OF THE DRYER, THE CONFIGURATION OF

THE DUCTING MAY REQUIRE GREATER THAN 3” OF

REAR CLEARANCE.

Gas Dryers Only:

•

No other fuel burning appliance shall be installed

in the same closet as a gas dryer.

•

The dryer must be disconnected from the gas

supply piping during pressure testing at pressures

greater than ½ psi (3.5 kPa).

•

A 1/8 inch NPT minimum plugged tapping,

accessible for test gauge connection, must be

installed immediately upstream of the gas supply

connection to the dryer.

MINIMUM CLEARANCE OTHER THAN

ALCOVE OR CLOSET INSTALLATION

Minimum clearance to combustible surfaces and

for air opening are: 0” both sides, 1” rear and 1” top.

Consideration must be given to provide adequate

clearance for installation and service.

17

Installation Instructions

CONNECTING INLET HOSES

CONNECTING INLET HOSES (cont.)

7. Using pliers, tighten all the couplings with an

additional two–thirds turn.

NOTE: Do not overtighten. Damage to the couplings

may result.

8. Turn the water faucet on.

9. Check for leaks around the ‘’Y’’ connector, faucet

and hose couplings.

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed

within 42 in. (107 cm) of your washer’s water

inlet. The faucets MUST be 3/4 in. (1.9 cm) garden

hose-type so inlet hoses can be connected. Water

pressure MUST be between 10 and 120 pounds

per square inch. Your water department can

advise you of your water pressure.

NOTE: A water softener is recommended to reduce

buildup of scale inside the steam generator if the

home water supply is very hard.

To produce steam, the dryer must connect to

the cold water supply. Since the washer must

also connect to the cold water, a “Y” connector

is inserted to allow both inlet hoses to make that

connection at the same time.

NOTE: Use new inlet hoses; never use old hoses.

1. Turn the cold water faucet off. Remove the

washer inlet hose from the washer fill valve

connector (cold).

2. Ensure the rubber flat washer is in place and

attach one female coupling of the short hose

provided onto the washer fill valve connector.

Tighten by hand until firmly seated.

3. Attach one male end of the “Y” connector to the

other female coupling of the short hose. Ensure

the rubber flat washer is in place. Tighten by

hand until firmly seated.

4. Insert the filter screen in the coupling of the

washer’s inlet hose. If a rubber flat washer is

already in place remove it before installing the

filter screen. Attach this coupling to one male end

of the ‘’Y’’ connector. Tighten by hand until firmly

seated.

5. Ensure the rubber flat washer is in place and

attach a 4 ft. to 6 ft. long water inlet hose (may

need to be purchased separately) to one male

end of the ‘’Y’’ connector. Tighten by hand until

firmly seated.

6. Ensure the rubber flat washer is in place and

attach the other end of the dryer’s long inlet

hose to the fill valve connector at the bottom of

the dryer back panel. Tighten by hand until firmly

seated.

CONNECTING INLET HOSES

Installation Instructions

CONNECTING A GAS DRYER (skip for electric dryers)

• Before beginning the installation, turn off the

circuit breaker(s) or remove the dryer’s circuit

fuse(s) at the electrical box. Be sure the dryer

cord is unplugged from the wall.

• Turn the dryer’s gas shut-off valve in the supply

line to the OFF position.

• Disconnect and discard old flexible gas connector

and ducting material.

Shut-off

Valve

18

MATERIALS YOU WILL NEED

 4” dia. metal elbow



Pipe compound or

PTFE tape



Flexible gas line

connector



Duct clamps (2) or

Spring clamps (2)



Safety glasses



4” dia. metal duct

(recommended)



4” Cover plate (Kit

WE49X22606)



4” dia., UL-listed

flexible metal duct

(if needed)



Gloves

 Soap solution for

leak detection



Exhaust hood



Duct tape



Gas pipe adapters (2),

elbow and pipe plug

TOOLS YOU WILL NEED

 10” Adjustable

wrenches (2)



8” Pipe wrench



Flat-blade

screwdriver



Level



Slip-joint pliers

 4’-6’ Water Hose

(on some models)

Installation Instructions

GAS REQUIREMENTS

DRYER GAS SUPPLY CONNECTION

GAS SUPPLY

• A 1/8” National Pipe Taper thread plugged

tapping, accessible for test gauge connection,

must be installed immediately upstream of the

gas supply connection to the dryer. Contact

your local gas utility should you have questions

on the installation of the plugged tapping.

•

Supply line is to be 1/2” rigid pipe and equipped

with an accessible shutoff within 6 feet of, and

in the same room with, the dryer.

•

Use pipe thread compound appropriate for

natural or LP gas or use PTFE tape.

•

Connect flexible metal connector to dryer and

gas supply.

3/8” NPT MALE THREAD GAS SUPPLY

NOTE: Add to vertical dimension

the distance between cabinet

bottom to floor.

4

7

ø16” (11.27 cm)

1

19

ø32”

(4.05 cm)

ADJUSTING FOR ELEVATION

• Gas clothes dryers input ratings are based on

sea level operation and need not be adjusted

for operation at or below 2000 ft. elevation. For

operation at elevations above 2000 ft., input

ratings should be reduced at a rate of 4 percent

for each 1000 ft. above sea level.

•

Installation must conform to local codes and

ordinances or, in their absence, the NATIONAL

FUEL GAS CODE, ANSI Z223.

You must use with this dryer a flexible metal

connector (listed connector ANSI Z21.24 / CSA 6.10).

The length of the connect shall not exceed 3 ft.

- Explosion Hazard

WARNING

• Use a new CSA International approved flexible

gas supply line. Never reuse old flexible

connectors.

• Install an individual manual shut-off valve

within 6ft. of the dryer in accordance with the

National Fuel Gas Code, ANSI Z223.1/NFPA 54.

• Securely tighten all gas connections.

• If connected to LP gas, have a qualified person

make sure gas pressure DOES NOT exceed 13”

water column.

• Examples of a qualified person include: licensed

heating personnel, authorized gas company

personnel, and authorized service personnel.

• Failure to do so can result in death, explosion,

or fire.

19

• The installation must conform with local codes,

or in the absence of local codes, with the

National Fuel Gas Code, ANSI Z223.1/NFPA 54,

or the Natural Gas and Propane Installation

Code, CSA B149.1.

- Fire Hazard

WARNING

FOR USE WITH NATURAL GAS ONLY

Dryer as produced by manufacturer is to be used only

with a natural gas supply. A manufacturer-supplied

conversion kit is required to convert this dryer for

propane gas supply. Use propane gas conversion

kit WE25M87. Conversion must be made by properly

trained and qualified personnel in accordance with

local codes and ordinances.

Install a 1/8” NPT plugged tapping to the dryer

gas line shut-off valve for checking gas inlet

pressure.

Install a flare union adapter to the plugged

tapping.

NOTE: Apply pipe compound or PTFE tape

to the threads of the adapter and plugged

tapping.

Installation Instructions

Attach the flexible metal gas line connector to

the adapter.

B

Tighten the flexible gas line connection, using

two adjustable wrenches.

C

D

Tighten all connections, using two adjustable

wrenches. Do not overtighten.

E

CONNECTING THE DRYER TO THE GAS

SUPPLY (cont.)

Open the gas shut-off valve.

F

Apply pipe compound

or PTFE tape to all

male threads.

Shut-Off

Valve

Plugged

Tapping

CONNECTING THE DRYER TO THE GAS

SUPPLY

Install a female 3/8” NPT elbow at the end of the

dryer gas inlet.

Install a 3/8” flare union adapter to the female

elbow.

IMPORTANT: Use a pipe wrench to securely hold

on to the end of the dryer gas inlet to prevent

twisting the inlet.

NOTE: Apply pipe compound or PTFE tape to the

threads of the adapter and dryer gas inlet.

A

Apply pipe compound to the

adapter and dryer gas inlet.

Elbow

Adapter

Items not supplied

Adapter

1/8” NPT

Pipe Plug for

Checking Gas

Inlet Pressure

Shut-Off Valve

Pipe size at

least 1/2”

3/8” NPT

New Metal

Flexible Gas

Line Connector

CONNECTING A GAS DRYER (cont.)

20

La page charge ...

GE GFD48ESPKDG Manuel utilisateur

GE GFD48ESPKDG Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents