EGO HT2411-FC Manuel utilisateur

WARNING: To reduce the risk of injury, the user must read and understand the

Operator’s Manual before using this product. Save these instructions for future reference.

OPERATOR'S MANUAL

56-VOLT

LITHIUM-ION

CORDLESS

HEDGE TRIMMER

MODEL NUMBER HT2410/HT2410-FC

Español p. 57

Français p. 27

17-0405_EGO_HT2400_HedgeTrimmer_manual_NA_V2

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC2

TABLE OF CONTENTS

Safety Symbols ..........................................4

Safety Instructions .....................................5-11

Introduction ............................................12

Speciﬁcations ..........................................12

Assembly ..............................................13

Packing List ............................................13

Description .........................................14-15

Operation ...........................................16-20

Maintenance ........................................21-22

Troubleshooting .........................................23

Warranty ...........................................24-25

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC 3

READ ALL INSTRUCTIONS!

READ & UNDERSTAND

OPERATOR’S MANUAL

WARNING:

Some dust created by power cutting contains chemicals known to

the state of California to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

 Lead from lead-based paints

 Crystalline silica from bricks and cement and other masonry products, and

 Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemical: work in a well-ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to ﬁlter out microscopic particles.

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC4

SAFETY SYMBOLS

The purpose of safety symbols is to attract your attention to possible dangers. The

safety symbols and the explanations with them deserve your careful attention and

understanding. The symbol warnings do not, by themselves, eliminate any danger. The

instructions and warnings they give are no substitutes for proper accident prevention

measures.

WARNING:

Be sure to read and understand all safety instructions in this

Operator’s Manual, including all safety alert symbols such as “DANGER,” “WARNING,”

and “CAUTION” before using this tool. Failure to following all instructions listed below

may result in electric shock, ﬁre, and/or serious personal injury.

SYMBOL MEANING

SAFETY ALERT SYMBOL:

Indicates DANGER, WARNING, OR CAUTION.

May be used in conjunction with other symbols or pictographs.

WARNING!

The operation of any power tools can result in foreign

objects being thrown into your eyes, which can result in severe eye

damage. Before beginning power tool operation, always wear safety

goggles or safety glasses with side shield and a full-face shield when

needed. We recommend a Wide Vision Safety Mask for use over

eyeglasses or standard safety glasses with side shields. Always use eye protection

which is marked to comply with ANSI Z87.1.

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC 5

SAFETY INSTRUCTIONS

This page depicts and describes safety symbols that may appear on this product. Read,

understand, and follow all instructions on the machine before attempting to assemble

and operate.

Safety Alert Indicates a potential personal injury hazard.

Read &

Understand

Operator’s

Manual

To reduce the risk of injury, user must read

and understand the operator’s manual before

using this product.

Eye Protection

Always wear safety goggles or safety glasses

with side shields and a full face shield when

operating this product.

Danger- Keep

Hands Away

from Blades

Contact with blade will result in serious

personal injury.

Recycle Symbols

This product uses lithium-ion (Li-ion)

batteries. Local, state, or federal laws may

prohibit disposal of batteries in ordinary

trash. Consult your local waste authority for

information regarding available recycling and/

or disposal options.

IPX4

Ingress

Protection

Degree

Protection from splashing water

V

Volt Voltage

mm Millimeter Length or size

in. Inch Length or size

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC6

Direct Current Type or a characteristic of current

n

0

No-Load Speed Rotational speed, at no load

SPM

Strokes Per

Minute

Stroke speed, at no load

kg Kilogram Weight

lb Pound Weight

GENERAL POWER TOOL SAFETY WARNINGS

WARNING:

Read all safety warnings and instructions. Fail to follow the

warnings and instructions may result in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warning refers to your mains-operated (corded) power tool

or battery-operated (cordless) power tool.

WORK AREA SAFETY

 Keep work area clean and well lit. Cluttered or dark areas invite accidents.

 Do not operate power tools in explosive atmospheres, such as in the presence

of ﬂammable liquids, gases or dust. Power tools create sparks which may ignite

the dust or fumes.

 Keep children and bystanders away while operating a power tool. Distractions

can cause you to lose control.

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC 7

ELECTRICAL SAFETY

 Power tool plugs must match the outlet. Never modify the plug in any way. Do

not use any adapter plugs with earthed (grounded) power tools. Unmodiﬁed

plugs and matching outlets will reduce risk of electric shock.

 Avoid body contact with earthed or grounded surfaces, such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric shock if

your body is earthed or grounded.

 Do not expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

 Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

 When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric

shock.

 If operating a power tool in a damp location is unavoidable, use a GFCI

protected supply. Use of a GFCI reduces the risk of electric shock.

PERSONAL SAFETY

 Stay alert, watch what you are doing and use common sense when operating

a power tool. Do not use a power tool while you are tired or under the

inﬂuence of drugs, alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

 Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal injuries.

 Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the

tool. Carrying power tools with your ﬁnger on the switch or energizing power tools

that have the switch on invites accidents.

 Remove any adjusting key or wrench before turning the power tool on. A

wrench or a key left attached to a rotating part of the power tool may result in

personal injury.

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC8

 Do not overreach. Keep proper footing and balance at all times. This enables

better control of the power tool in unexpected situations.

 Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing

and gloves away from moving parts. Loose clothes, jewelry or long hair can be

caught in moving parts.

 If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust devices

can reduce dust-related hazards.

POWER TOOL USE AND CARE

 Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and more safely at the rate for which it

was designed.

 Do not use the power tool if the switch does not turn it on and off. Any power

tool that cannot be controlled with the switch is dangerous and must be repaired.

 Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce the risk of starting the power

tool accidentally.

 Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

 Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tools

operation. If damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

 Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

 Use the power tool, accessories, tool bits, etc. in accordance with these

instructions, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended could

result in a hazardous situation.

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC 9

BATTERY TOOL USE AND CARE

 Recharge only with the charger speciﬁed by the manufacturer. A charger that

is suitable for one type of battery pack may create a risk of ﬁre when used with

another battery pack.

 Use power tools only with speciﬁcally designated battery packs. Use of any

other battery packs may create a risk of injury and ﬁre.

 When battery pack is not in use, keep it away from other metal objects, like

paper clips, coins, keys, nails, screws or other small metal objects that can

make a connection from one terminal to another. Shorting the battery terminals

together may cause burns or a ﬁre.

 Under abusive conditions, liquid may be ejected from the battery; avoid

contact. If contact accidentally occurs, ﬂush with water. If liquid contact eyes,

additionally seek medical help. Liquid ejected from the battery may cause irritation

or burns.

SERVICE

 Have your power tool serviced by a qualiﬁed repair person using only

identical replacement parts. This will ensure that the safety of the power tool is

maintained.

HEDGE TRIMMER SAFETY WARNINGS

DANGER

– Keep hands away from blade. Contact with blade will result in serious

personal injury.

 Keep all parts of the body away from the cutter blade. Do not remove cut

material or hold material to be cut when blades are moving. Make sure the

switch is off when clearing jammed material. Blades coast after turn off.

A moment of inattention while operating the hedge trimmer may result in serious

personal injury.

 Carry the hedge trimmer by the handle with the cutter blade stopped. When

transporting or storing the hedge trimmer always ﬁt the cutting device cover.

Proper handling of the hedge trimmer will reduce possible personal injury from the

cutter blades.

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC10

 Hold the power tool by insulated gripping surfaces only, because the cutter

blade may contact hidden wiring. Cutter blades contacting a “live” wire may

make exposed metal parts of the power tool “live” and could give the operator an

electric shock.

 Keep cable away from cutting area. During operating the cable may be hidden in

shrubs and can be accidentally cut by the blade.

 Use both hands when operating the hedge trimmer. Using one hand could

cause loss of control and result in serious personal injury.

IMPORTANT SAFETY INSTRUCTIONS

 Do not charge the battery pack in rain, or in wet locations.

 Use only with the battery packs and chargers listed below:

BATTERY CHARGER

BA1120, BA1120-FC, BA1400, BA1400-FC,

BA2240, BA2240-FC, BA2800, BA2800-FC,

BA4200, BA4200-FC

CH2100, CH2100-FC,

CH5500, CH5500-FC

 Do not grasp the exposed cutting blades or cutting edges when picking up or holding

the hedge trimmer.

 Do not use on a ladder, rooftop, tree, or other unstable support. Stable footing on a

solid surface enables better control of the hedge trimmer in unexpected situations.

 Never allow children to operate the hedge trimmer.

 Never remove or tamper with safety devices. Check their proper operation regularly.

Never do anything to interfere with the intended function of a safety device or to

reduce the protection provided by a safety device.

 Never operate the hedge trimmer without proper guards, plates, or other safety

protective devices in place.

 Check damaged parts before further use of the hedge trimmer. Any part that is

damaged should be carefully checked to determine that it will operate properly

and perform its intended function. Check for alignment of moving parts, binding of

moving parts, breakage of parts, mounting, and any other condition that may affect

its operation. Any part that is damaged should be properly repaired or replaced by an

authorized service center unless indicated elsewhere in this manual.

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC 11

 Check the blade and motor mounting bolts at frequent intervals for proper tightness.

Also, visually inspect blade for damage (e.g., bent, cracked, and worn). Replace the

blade only with a blade from the original equipment manufacturer (OEM).

 Replace the blade if it is bent or cracked. An unbalanced blade causes vibration that

could damage the motor drive unit or cause personal injury.

 If the equipment should start to vibrate abnormally, stop the motor and check

immediately for the cause. Vibration is generally a warning of trouble.

 The trimmer shall be used to cut stems less than 1 in. (26mm) thick.

 Trim only in daylight or in good artiﬁcial light.

 Remove or disconnect battery before servicing, cleaning, or removing material from

the hedge trimmer.

 Do not wash with a hose; avoid getting water in motor and electrical connections.

 When servicing use only identical replacement parts listed in this manual. Use of

parts which do not meet the original equipment speciﬁcations may lead to improper

performance and compromised safety.

 Do not incinerate the appliance even if it is severely damaged. The batteries can

explode in a ﬁre.

 Follow instructions for lubricating and changing accessories.

 Keep handles dry, clean and free from oil and grease.

 Do not expose a battery pack or tool to ﬁre or excessive temperature. Exposure to

ﬁre or temperature above 212 °F (100°C) may cause explosion.

 Save these instructions. Refer to them frequently and use them to instruct

others who may use this tool. If you loan this tool to someone else, also loan these

instructions to them to prevent misuse of the product and possible injury.

SAVE THESE INSTRUCTIONS!

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC12

INTRODUCTION

Congratulations on your selection of the new 56V Lithium-ion powered hedge trimmer.

It has been designed, engineered and manufactured to give you the best possible

dependability and performance.

Should you experience any problem you cannot easily remedy, please contact EGO

customer service center 1-855-EGO-5656.

This manual contains important information on to the safe assembly, operation and

maintainance of your product. Read it carefully before using the product. Keep this

manual handy so you can refer to it at any time.

SERIAL NUMBER _____________________ DATE OF PURCHASE _________________

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP THEM IN A

SAFE PLACE FOR FUTURE REFERENCE

SPECIFICATIONS

Voltage 56V

No Load Speed (n

0

) 3000 SPM

Cutting Length 24 in. (610 mm)

Recommended Operating Temperature 32°F-104°F(0°C-40°C)

Recommended Storage Temperature -4°F-158°F(-20°C-70°C)

Weight (Without battery pack, blade guard) 6.16 lb. (2.80kg)

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC 13

ASSEMBLY

WARNING:

If any parts are damaged or missing, do not operate this product

until the parts are replaced. Use of this product with damaged or missing parts could

result in serious personal injury.

WARNING:

Do not attempt to modify this product or create accessories not

recommended for use with this product. Any such alteration or modiﬁcation is misuse

and could result in a hazardous condition leading to possibly serious personal injury.

WARNING:

To prevent accidental starting that could cause serious personal

injury, always remove the battery pack from the tool when assembling parts, making

adjustments, cleaning, or when not in use.

UNPACKING

This product has been shipped completely assembled.

 Carefully remove the product and any accessories from the box. Make sure that

all items listed in the packing list are included.

 Inspect the tool carefully to make sure that no breakage or damage occurred

during shipping.

 Do not discard the packing material until you have carefully inspected and

satisfactorily operated the tool.

 If any parts are damaged or missing, please return the product to the place of

purchase.

PACKING LIST

PART NAME QUANTITY

Hedge Trimmer 1

Blade Guard 1

Operator's Manual 1

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC14

DESCRIPTION

KNOW YOUR HEDGE TRIMMER (Fig.1)

The safe use of this product requires an understanding of the information on the tool

and in this operator’s manual, as well as knowledge of the project you are attempting.

Before using this product, familiarize yourself with all operating features and safety

rules.

Blade

Hanging hole Blade guard

Hanging hole

Hand guard

Tip protector

Front handle

Lock-off button

Rear handle

Battery-release button

Electric contacts

Latch

Front switch lever

Rear switch lever

Battery-mounting slot

Batter-ejection

1

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC 15

Hand Guard

Helps to protect the operator’s hands; deﬂects chips or other debris away from the

operator.

Front Handle

For easy control of the tool.

Rear Handle

Ergonomic handle with overmold improves comfort and grip.

Lock-off Button

Helps to prevent accidental or unauthorized activation of the switch lever. It must be

depressed before the trigger switch can be activated.

Front Switch Lever/Rear Switch Lever

The hedge trimmer can be started only if both switch levers (in rear and front of the

handle) are depressed simultaneously.

Blades

Hardened steel blades for cutting hedges and shrubs.

Blade Guard

The blade guard keeps the operator from coming in contact with the sharp blades

when the tool is not in use. It also helps keep the blades from being nicked or damaged

when the tool is in transportation and storage.

Tip Protector

Protects the outer end of the blade.

Battery-Release Button

Press to release the battery pack from the tool.

Latch

Locks the battery pack in place when installed on the tool.

Battery-ejection

Aids in removing the battery.

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC16

OPERATION

WARNING:

Do not allow familiarity with this product to make you careless.

Remember that a careless fraction of a second is sufﬁcient to inﬂict serious injury.

WARNING:

Always wear eye protection that complies with ANSI Z87.1. Failure

to do so could result in objects being thrown into your eyes and other possible serious

injuries.

WARNING:

Do not use any attachments or accessories not recommended by the

manufacturer of this product. The use of attachments or accessories not recommended

can result in serious personal injury.

WARNING:

To prevent serious personal injury, remove the battery pack from the

tool before servicing, cleaning, changing attachments or removing material from the

unit.

Before each use, inspect the entire product for damaged, missing, or loose parts such

as screws, nuts, bolts, caps, etc. Securely tighten all fasteners and caps and do not

operate this product until all missing or damaged parts are replaced.

APPLICATIONS

You may use this product for the purposes listed below.

 Trimming hedges, shrubs, and bushes with branch diameters less than 1 in.

(26 mm).

TO INSTALL/REMOVE BATTERY PACK (Fig. 2 & 3)

NOTE:

Fully charge the battery pack

before ﬁrst use.

To Install Battery Pack (Fig. 2)

 Align the ribs of the battery pack

with the battery-mounting slots on

the hedge trimmer.

 Slide the battery pack in until it

snaps into position.

2

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC 17

NOTE: Make sure that the latch on the

hedge trimmer snaps into place and the

battery pack is secured to the tool before

beginning operation.

To Remove Battery Pack (Fig. 3)

WARNING:

Always be aware for

the location of your feet, children, or pets

when pressing the battery-release button.

Serious injury could result if the battery

pack falls. NEVER remove the battery

pack at a high location.

 Press the battery-release button; the

battery pack will disengage from the

latch.

 Grasp the battery pack and remove

it from the hedge trimmer.

HOLDING THE HEDGE TRIMMER

(Fig. 4, 5 & 6)

The unit has both a front and rear handle.

With the blade directed away from you,

hold the unit by both handles.

The switch lever in the front handle

can be activated on any of the three

sides, giving you many choices for a

comfortable grip when performing cutting

operations.

WARNING:

Always keep both

hands on the hedge trimmer handles.

Never hold shrubs with one hand while

operating the hedge trimmer with the

other hand. Failure to heed this warning

may result in serious injury.

Press to Release

3

4

5

6

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC18

STARTING/STOPPING THE HEDGE TRIMMER

Before starting the hedge trimmer:

 Make sure that you have a secure and balance footing.

 Stand upright and hold the hedge trimmer in a relaxed position.

 Remove the blade guard.

 Make sure the cutting blade is not touching the ground or any other objects.

 Hold the unit with both hands: one hand on the rear handle and one hand on the

front handle.

TO START THE HEDGE TRIMMER

1. Install the battery pack.

2. Depress and hold the switch lever in the front handle with one hand.

3. Press and hold the lock-off button with the thumb of your other hand, then squeeze

the rear switch lever with your ﬁngers to start the hedge trimmer. Release the lock-

off button and continue to squeeze the trigger for continued operation.

TO STOP THE HEDGE TRIMMER

Move the hedge trimmer away from the cutting area and release the rear switch lever

to stop the hedge trimmer.

WARNING:

Always remove the battery pack from the hedge trimmer during

work breaks and after ﬁnishing work.

USING THE HEDGE TRIMMER

WARNING:

If the blade jams on any electrical cord or line, DO NOT TOUCH THE

BLADE! IT CAN BECOME ELECTRICALLY LIVE AND VERY DANGEROUS. Continue to hold

the hedge trimmer by the insulated rear handle or lay it down and away from you in

a safe manner. Disconnect the electrical service to the damaged line or cord before

attempting to free the blade from the line or cord. Failure to heed this warning will

result in serious personal injury or possible death.

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC 19

WARNING:

If any parts are missing, damaged or broken, do not operate your

trimmer until they have been replaced. Failure to do so could result in possibly serious

personal injury.

WARNING:

To prevent serious personal injury, always use both the front handle

and the rear handle to hold the hedge trimmer during operation.

WARNING:

To prevent serious personal injury, keep hands away from blades.

Do not attempt to remove cut material or hold material to be cut when the blades

are moving. Make sure that the blades have totally stopped and the battery pack is

removed before clearing jammed material from blades. Do not grasp the exposed

cutting blades or cutting edges when picking up or holding the unit.

WARNING:

Clear the area to be cut before each use. Remove all objects, such

as cords, lights, wire, or string that could become entangled in the cutting blade and

create a risk of serious personal injury.

 Before starting the hedge trimmer, maintain proper footing and balance and do

not overreach. Wear safety goggles, non-skid footwear and rubber gloves. Hold

the unit with both hands with the cutting blades directed away from you. Always

use the hedge trimmer properly.

 Do not trim too much at one time. This can cause the blades to bind and slow,

reducing the cutting efﬁciency.

 Do not force the hedge trimmer through heavy shrubbery. This can cause the

blades to bind and slow down. If the blades slow down, reduce the pace of

your work.

 When trimming new growth, use a wide sweeping action, so that the stems are

fed directly into the cutting blade. Older growth will have thicker stems and will

be trimmed most easily by using a sawing movement.

 Always cut stems or twigs that are less than 1 in. thick. Use a non-powered hand

saw or pruning saw to trim large stems.

56V LITHIUM-ION CORDLESS HEDGE TRIMMER — HT2410/HT2410-FC20

TOP CUTTING (Fig. 7)

Use a wide sweeping motion. A slight

downward tilt of the cutting blades in

the direction of motion gives the best

cutting results. If desired, you can use a

string to help guide you as you cut your

hedge level. Decide how high you want

the hedge. Then, stretch a piece of string

along the hedge at this height. Trim the

hedge just above this guide line.

SIDE CUTTING (Fig. 8)

When trimming the sides of the hedge, begin at the bottom and cut upwards. Trim the

side of a hedge so that it will be slight narrower at the top.This shape will expose more

of the hedge to sunlight, resulting in a more uniform growth.

8

7

La page charge ...

EGO HT2411-FC Manuel utilisateur

Ce manuel convient également à

EGO HT2411-FC Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents