CHAUVET DJ GigBAR Move + ILS Manuel utilisateur

User Manual - EU Version

English

Español

Français

Deutsch

Nederlands

LASER LIGHT

AVOID DIRECT EYE EXPOSURE

CLASS 3R LASER PRODUCT

CLASSIFIED PER EN/IEC 60825-1: 2014

Complies with FDA performance standards for

laser products except for deviations pursuant

to Laser Notice No. 56, dated May 8, 2019.

Table of Contents

GigBAR MOVE + ILS User Manual Rev. 8

2

TABLE OF CONTENTS

1. Before You Begin ......................................................................................... 12

What Is Included ...................................................................................................... 12

Unpacking Instructions............................................................................................. 12

Text Conventions ..................................................................................................... 12

Symbols ................................................................................................................... 12

Disclaimer ................................................................................................................ 13

FCC Compliance...................................................................................................... 13

Intellectual Property ................................................................................................. 13

Safety Notes............................................................................................................. 14

Laser Safety Notes................................................................................................... 15

Laser Safety Label Reproduction............................................................................. 16

Laser Emission Data................................................................................................ 16

Laser Compliance Statement................................................................................... 16

2. Introduction................................................................................................... 17

Product Overview..................................................................................................... 17

Product Dimensions................................................................................................. 18

3. Setup.............................................................................................................. 19

AC Power................................................................................................................. 19

Fuse Replacement ......................................................................................................... 19

Power Linking................................................................................................................. 19

ILS Connection......................................................................................................... 19

Mounting .................................................................................................................. 20

Orientation...................................................................................................................... 20

Rigging........................................................................................................................... 20

Proper Usage........................................................................................................... 20

4. Operation....................................................................................................... 21

Control Panel Operation........................................................................................... 21

Menu Map ................................................................................................................ 21

Configuration (Standalone) ...................................................................................... 24

Automatic Mixed Effect Mode ........................................................................................ 24

Sound-Active Mixed Effect Mode................................................................................... 24

Sound Sensitivity............................................................................................................ 24

Dimmer........................................................................................................................... 24

Strobe............................................................................................................................. 25

Program Time ................................................................................................................ 25

Pars Color ...................................................................................................................... 25

Spot Speed .................................................................................................................... 25

Sound Lost..................................................................................................................... 25

Pan Reverse .................................................................................................................. 26

Tilt Reverse.................................................................................................................... 26

Pan Range ..................................................................................................................... 26

Tilt Range....................................................................................................................... 26

Factory Reset................................................................................................................. 26

Configuration (DMX) ................................................................................................ 27

DMX Channel Assignments and Values .................................................................. 28

Gobos............................................................................................................................. 28

52 Channels................................................................................................................... 28

30 Channels................................................................................................................... 32

3 Channels..................................................................................................................... 34

Wireless Footswitch ................................................................................................. 35

Footswitch Operation ..................................................................................................... 35

GigBAR RF Remote Control .................................................................................... 36

GigBAR RF Remote Operation ...................................................................................... 36

Master/Slave Mode .................................................................................................. 38

5. Maintenance.................................................................................................. 39

Product Maintenance ............................................................................................... 39

6. Technical Specifications.............................................................................. 40

Contact Us......................................................................................................... 42

Warranty & Returns.................................................................................................. 42

GigBAR MOVE + ILS User Manual Rev. 8

Tabla de contenido

3

TABLA DE CONTENIDO

1. Antes de Empezar ........................................................................................ 43

Qué va Incluido ........................................................................................................ 43

Instrucciones de Desembalaje................................................................................. 43

Convenciones del Manual........................................................................................ 43

Símbolos .................................................................................................................. 43

Exención de responsabilidad ................................................................................... 44

Cumplimiento de la FCC.......................................................................................... 44

Propiedad intelectual................................................................................................ 44

Notas de Seguridad ................................................................................................. 45

Notas de Seguridad sobre Láser ............................................................................. 46

Reproducción de la Etiqueta de Seguridad del Láser.............................................. 47

Datos de Emisión Láser........................................................................................... 47

Declaración de Conformidad Láser.......................................................................... 47

2. Introducción.................................................................................................. 48

Vista general del producto ....................................................................................... 48

Dimensiones del producto........................................................................................ 49

3. Instalación..................................................................................................... 50

Corriente alterna ...................................................................................................... 50

Sustitución del fusible .................................................................................................... 50

Alimentación en cadena................................................................................................. 50

Conexión ILS............................................................................................................ 51

Montaje .................................................................................................................... 51

Orientación..................................................................................................................... 51

Colocación ..................................................................................................................... 51

Uso Adecuado.......................................................................................................... 52

4. Funcionamiento............................................................................................ 53

Funcionamiento del panel de control ....................................................................... 53

Mapa de menú ......................................................................................................... 53

Configuración (Independiente)................................................................................. 57

Modo Efecto Mezclado Automático................................................................................ 57

Modo Efecto Mezclado de Sonido Activo por Sonido .................................................... 57

Sensibilidad al sonido .................................................................................................... 57

Atenuador....................................................................................................................... 57

Estroboscopio ................................................................................................................ 58

Tiempo de programa...................................................................................................... 58

Colores de pars.............................................................................................................. 58

Velocidad puntual........................................................................................................... 58

Pérdida de sonido .......................................................................................................... 58

Paneo inverso ................................................................................................................ 59

Inclinación inversa.......................................................................................................... 59

Rango de paneo............................................................................................................. 59

Rango de inclinación...................................................................................................... 59

Restablecimiento de fábrica........................................................................................... 59

Configuración (DMX)................................................................................................ 60

Dirección de inicio .......................................................................................................... 60

Valores y asignaciones de canal DMX..................................................................... 61

Gobos............................................................................................................................. 61

52 canales...................................................................................................................... 61

30 canales...................................................................................................................... 65

3 canales........................................................................................................................ 67

Funcionamiento del Conmutador de Pie.................................................................. 68

Control remoto RF.................................................................................................... 69

Funcionamiento de control remoto RF .......................................................................... 69

Modo Maestro/Esclavo............................................................................................. 71

5. Mantenimiento .............................................................................................. 72

Mantenimiento del producto..................................................................................... 72

6. Especificaciones Técnicas.......................................................................... 73

Contacto............................................................................................................ 75

Garantía y devoluciones .......................................................................................... 75

Table des matières

GigBAR MOVE + ILS User Manual Rev. 8

4

TABLE DES MATIÈRES

1. Avant de Commencer................................................................................... 76

Ce Qui Est Compris ................................................................................................. 76

Instructions Relatives au Déballage......................................................................... 76

Conventions manuelles............................................................................................ 76

Symboles ................................................................................................................. 76

Clause de Non-Responsabilité................................................................................. 77

Conformité FCC ....................................................................................................... 77

Propriété intellectuelle.............................................................................................. 77

Consignes de Sécurité............................................................................................. 78

Consignes de Sécurité Relatives au Laser .............................................................. 79

Reproduction de l’Étiquette de Sécurité Laser......................................................... 80

Données d'émission laser ........................................................................................ 80

Déclaration de Conformité Laser ............................................................................. 80

2. Introduction................................................................................................... 81

Vue d'ensemble du produit ...................................................................................... 81

Dimensions du produit ............................................................................................. 82

3. Configuration................................................................................................ 83

Alimentation CA ....................................................................................................... 83

Remplacement des fusibles........................................................................................... 83

Connexion électrique ..................................................................................................... 83

Connexion ILS.......................................................................................................... 84

Installation................................................................................................................ 84

Orientation...................................................................................................................... 84

Suspension .................................................................................................................... 84

Utilisation Adéquate ................................................................................................. 85

4. Fonctionnement............................................................................................ 86

Fonctionnement du Panneau de Commande .......................................................... 86

Plan du menu........................................................................................................... 86

Configuration (Autonome)........................................................................................ 90

Mode effet mélangé automatique................................................................................... 90

Mode effet mélangé activé par le son ............................................................................ 90

Sensibilité sonore........................................................................................................... 90

Dimmer........................................................................................................................... 90

Stroboscope................................................................................................................... 91

L’heure du programme................................................................................................... 91

Couleurs de pars............................................................................................................ 91

Vitesse du spot............................................................................................................... 91

Perte de son................................................................................................................... 91

Panoramique inversé ..................................................................................................... 92

Tilt inversé...................................................................................................................... 92

Plage de pan.................................................................................................................. 92

Plage de tilt .................................................................................................................... 92

Réinitialisation des paramètres d'usine.......................................................................... 92

Configuration (DMX) ................................................................................................ 93

Adresse de départ.......................................................................................................... 93

Affectation de canaux DMX et valeurs..................................................................... 94

Gobos............................................................................................................................. 94

52 canaux....................................................................................................................... 94

30 canaux....................................................................................................................... 98

3 canaux......................................................................................................................... 100

Utilisation de la pédale sans fil................................................................................. 101

RF télécommande.................................................................................................... 101

Fonctionnement de la télécommande RF ...................................................................... 102

Mode maître/esclave................................................................................................ 104

5. Entretien........................................................................................................ 105

Entretien de l'appareil .............................................................................................. 105

6. Spécificités Techniques............................................................................... 106

7. Nous Contacter............................................................................................. 108

Garantie et retours ................................................................................................... 108

GigBAR MOVE + ILS User Manual Rev. 8

Inhaltsverzeichnis

5

INHALTSVERZEICHNIS

1. Erste Schritte ................................................................................................ 109

Packungsinhalt......................................................................................................... 109

Anweisungen für das Auspacken............................................................................. 109

Konventionen des Handbuchs ................................................................................. 109

Symbole ................................................................................................................... 109

Haftungsausschluss................................................................................................. 110

FCC-Konformität ...................................................................................................... 110

Geistiges Eigentum.................................................................................................. 110

Sicherheitshinweise ................................................................................................. 111

Hinweise zur Lasersicherheit ................................................................................... 112

Warn- und Sicherheitsschilder auf dem Lasergerät................................................. 113

Laseremissionsdaten ............................................................................................... 113

Laser-Konformitätserklärung.................................................................................... 113

2. Einleitung ...................................................................................................... 114

Produktüberblick ...................................................................................................... 114

Produktabmessungen .............................................................................................. 115

3. Einrichten des Geräts .................................................................................. 116

Wechselstrom .......................................................................................................... 116

Auswechseln der Sicherung........................................................................................... 116

Reihenschaltung der Geräte .......................................................................................... 116

ILS-Anschluss .......................................................................................................... 116

Montage ................................................................................................................... 117

Montagerichtung ............................................................................................................ 117

Hängende Montage........................................................................................................ 117

Bestimmungsgemäße Verwendung......................................................................... 117

4. Betrieb ........................................................................................................... 118

Betrieb des Bedienfeldes ......................................................................................... 118

Menüstruktur ............................................................................................................ 118

Konfiguration (Einzelplatzmodus) ............................................................................ 122

Automatische-Modus ..................................................................................................... 122

Musiksteuerungs-Modus ................................................................................................ 122

Klangempfindlichkeit ...................................................................................................... 122

Dimmer........................................................................................................................... 123

Stroboskop..................................................................................................................... 123

Programmzeit................................................................................................................. 123

Pars-Farben ................................................................................................................... 123

Spot-Geschwindigkeit .................................................................................................... 123

Tonausfall....................................................................................................................... 124

Schwenken umgekehrt................................................................................................... 124

Neigen umgekehrt.......................................................................................................... 124

Schwenkbereich............................................................................................................. 124

Neigungsbereich ............................................................................................................ 125

Zurücksetzen auf Werkseinstellungen ........................................................................... 125

Konfiguration (DMX)................................................................................................. 125

Startadresse................................................................................................................... 125

DMX-Kanal – Zuordnungen und Werte.................................................................... 126

Gobos............................................................................................................................. 126

52-Kanal......................................................................................................................... 126

30-Kanal......................................................................................................................... 130

3-Kanal........................................................................................................................... 132

Betrieb mit drahtlosem Fußschalter ......................................................................... 133

GigBAR Funkfernbedienung .................................................................................... 133

Bedienung der GigBAR RF-Fernbedienung................................................................... 134

Master/Slave-Modus ................................................................................................ 136

5. Wartung......................................................................................................... 137

Wartung des Geräts................................................................................................. 137

6. Technische Daten......................................................................................... 138

Kontaktiere Uns................................................................................................ 140

Garantie und Reklamationen ................................................................................... 140

Inhoudsopgave

GigBAR MOVE + ILS User Manual Rev. 8

6

INHOUDSOPGAVE

1. Voordat tu begint.......................................................................................... 141

Wat is er inbegrepen................................................................................................ 141

Uitpakinstructies....................................................................................................... 141

Tekstconventies ....................................................................................................... 141

Symbolen ................................................................................................................. 141

Disclaimer ................................................................................................................ 142

FCC-naleving ........................................................................................................... 142

Intellectueel eigendom ............................................................................................. 142

Veiligheidsinstructies................................................................................................ 143

Veiligheidsinstructies voor de laser.......................................................................... 144

Reproductie van veiligheidsetiket voor de laser....................................................... 145

Emissiegegevens van de laser ................................................................................ 145

Nalevingsverklaring van de laser ............................................................................. 145

2. Inleiding......................................................................................................... 146

Productoverzicht ...................................................................................................... 146

Productafmetingen................................................................................................... 147

3. Instelling........................................................................................................ 148

AC-stroom................................................................................................................ 148

Vervangen van de zekering ........................................................................................... 148

Power Linking................................................................................................................. 148

ILS Aansluiting ......................................................................................................... 148

Montage ................................................................................................................... 149

Oriëntatie........................................................................................................................ 149

Opbouw.......................................................................................................................... 149

Correct gebruik......................................................................................................... 149

4. Werking ......................................................................................................... 150

Werking van het bedieningspaneel.......................................................................... 150

Menu Map ................................................................................................................ 150

Configuratie (zelfstandig) ......................................................................................... 153

Automatisch gemengd effect stand................................................................................ 153

Geluidsactieve modus.................................................................................................... 153

Geluidsgevoeligheid....................................................................................................... 153

Dimmer........................................................................................................................... 154

Stroboscoop................................................................................................................... 154

Programmatijd................................................................................................................ 154

Pars kleuren................................................................................................................... 154

Spotsnelheid .................................................................................................................. 154

Sound Lost..................................................................................................................... 155

Pannen omkeren............................................................................................................ 155

Kantelen omkeren.......................................................................................................... 155

Panbereik....................................................................................................................... 155

Kantelbereik ................................................................................................................... 155

Fabrieksinstellingen ....................................................................................................... 156

Configuratie (DMX) .................................................................................................. 156

Startadres....................................................................................................................... 156

DMX-kanaaltoewijzingen en waarden...................................................................... 157

Gobos............................................................................................................................. 157

52-kanaals...................................................................................................................... 157

30-kanaals...................................................................................................................... 161

3-kanaals........................................................................................................................ 163

Bediening van de voetschakelaar ............................................................................ 164

GigBAR RF afstandsbediening ................................................................................ 164

GigBAR RF-afstandsbediening ...................................................................................... 165

Master/Slave-modus ................................................................................................ 167

5. Onderhoud .................................................................................................... 168

Productonderhoud.................................................................................................... 168

6. Technische Specificaties............................................................................. 169

Neem contact Op.............................................................................................. 171

Garantie & Retouren ................................................................................................ 171

12

Before You Begin

GigBAR MOVE + ILS User Manual Rev. 8

1. Before You Begin

What Is Included

Unpacking Instructions

Carefully unpack the product immediately and check the container to make sure all the parts are in the

package and are in good condition.

Claims

If the box or the contents (the product and included accessories) appear damaged from shipping, or show

signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier

immediately may invalidate your claim. In addition, keep the box and contents for inspection.

For other issues, such as missing components or parts, damage not related to shipping, or concealed

damage, file a claim with Chauvet within 7 days of delivery.

Text Conventions

Symbols

• GigBAR MOVE + ILS

•Power cord

• RF remote

• Carrying bag

•Tripod

• Tripod carrying bag

• Footswitch

• User manual

Convention Meaning

1–512 A range of values

50/60 A set of values of which only one can be chosen

Settings A menu option not to be modified

<ENTER> A key to be pressed on the product’s control panel

ON A value to be entered or selected

Symbol Meaning

Critical installation, configuration, or operation information. Not following these

instructions may make the product not work, cause damage to the product, or cause

harm to the operator.

Important installation or configuration information. The product may not function

correctly if this information is not used.

Useful information.

Laser safety information.

13

GigBAR MOVE + ILS User Manual Rev. 8

Before You Begin

Disclaimer

Chauvet believes that the information contained in this manual is accurate in all respects. However,

Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss,

damage or disruption caused by any errors or omissions in this document, whether such errors or

omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the

content of this document without any obligation to notify any person or company of such revision, however,

Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest

version from www.chauvetdj.com.

FCC Compliance

This device complies with Part 15 Part B of the FCC rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause

undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

Intellectual Property

The works of authorship contained in this manual, including, but not limited to, all design, text and images

are owned by Chauvet.

Electronically published by Chauvet in the United States of America.

CHAUVET, the Chauvet logo, and GigBAR MOVE + ILS are registered trademarks or trademarks of

Chauvet & Sons LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other

company and product names and logos referred to herein may be trademarks of their respective

companies.

14

Before You Begin

GigBAR MOVE + ILS User Manual Rev. 8

Safety Notes

The Safety Notes include important laser system safety information. Read and understand all instructions

before powering on the laser for the first time. Knowing these safety instructions is crucial to avoiding laser

eye injury and breaking the law. Keep this User Manual in a safe place for future reference.

STOP AND READ ALL LASER SAFETY DATA

• Lasers can be hazardous and have unique safety considerations. Permanent eye injury and

blindness are possible if lasers are used incorrectly. Pay close attention to each safety

REMARK and WARNING statement in this User Manual. Read all instructions carefully

BEFORE operating this device.

• Always connect the product to a grounded circuit to avoid the risk of electrocution.

• Always disconnect the product from the power source before cleaning.

• Avoid direct eye exposure to the light source while the product is on.

• Make sure the power cord is not crimped or damaged.

• Never disconnect the product from power by pulling or tugging on the cord.

• If mounting the product overhead, always secure to a fastening device using a safety cable.

• Make sure there are no flammable materials close to the product when operating.

• Do not touch the product’s housing when operating because it may be very hot.

• This product is not intended for permanent installation.

• Always make sure that the voltage of the outlet to which you are connecting the product is

within the range stated on the decal or rear panel of the product.

• The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose the

product to rain or moisture.

• Always install the product in a location with adequate ventilation, at least 20 in (50 cm) from

adjacent surfaces.

• Be sure that no ventilation slots on the product’s housing are blocked.

• Never connect the product to a dimmer.

• Make sure to replace the fuse with another of the same type and rating.

• Always use the mounting bracket to carry the product.

• Do not switch the product on/off in short intervals. This will reduce the laser diode life.

• Do not shake this product. Avoid brute force when mounting or operating this product.

• ALWAYS use a safety cable when mounting the product overhead.

• The ambient operating temperature for the laser is 59 °F to 95 °F (15 °C to 35 °C). Do not

operate this product outside this range.

• In the event of a serious operating problem, stop using the product immediately.

• Never try to repair the product. Repairs carried out by unskilled people can lead to damage or

malfunction. Contact the nearest authorized technical assistance center.

CAUTION! Use of controls, adjustments, or procedures other than THOSE specified IN

THIS USER MANUAL may result in hazardous radiation exposure.

• Avoid direct eye contact with laser light. Never intentionally expose your eyes or others to

direct laser light.

• This laser product can potentially cause instant eye injury or blindness if laser light directly

strikes the eyes.

• It is illegal and dangerous to shine this laser into audience areas, where the audience or other

personnel could get direct laser beams or bright reflections into their eyes.

• It is a U.S. federal offense to shine any laser at aircraft.

• To eliminate wear and improve its lifespan, during periods of non-use completely disconnect

from power via breaker or by unplugging it.

• DO NOT attempt any repairs. Repairs and servicing must be carried out by a certified

technician. Unauthorized modifications are forbidden for safety reasons!

Keep this User Manual for future consultation. If transferring ownership of the product to

another user, be sure this document is kept with the laser.

15

GigBAR MOVE + ILS User Manual Rev. 8

Before You Begin

Non-Interlocked Housing Warning

Laser Safety Notes

Laser light is different from any other light. Laser light can cause eye injury if the product is not set up and

used properly. Laser light is a thousand times more concentrated than any other kind of light. This

concentration can cause instant eye injuries by burning the retina (the light-sensitive portion at the back of

the eye). The heat from a laser light cannot be felt, but it can still injure or blind product operators and the

audience. Even very small amounts of laser light at long distances are potentially hazardous.

DO NOT assume that exposure to an individual laser beam is safe, even a tiny beam split off from a larger

beam. This laser product uses dozens of milliwatts of laser power—Class 3B levels internally—and splits

them into multiple beams—Class 3R levels. The individual Class 3R level beams are potentially hazardous

to the eyes.

DO NOT assume that a moving laser light is safe. Laser light is never without risk. Since eye injuries can

occur instantly, it is critical to prevent the possibility of ANY direct eye exposure. According to laser safety

regulations, it is not legal to aim Class 3R lasers into areas where people can be exposed, even if the laser

is aimed below people’s faces, such as at a dance floor.

• This unit contains high power laser devices internally.

• Do not open the laser housing, due to potential exposure to unsafe levels of laser radiation.

• The laser power levels, accessible if the unit is opened, can cause instant blindness, skin

burns, and fires.

STOP AND READ ALL THE LASER SAFETY NOTES BELOW

• Do not operate the laser without first reading and understanding all the safety and technical

data in this manual.

• ALWAYS set up and install all laser effects so that any laser light is at least 3 meters (9.8 feet)

above the floor on which people are standing. See the Proper Usage section of this manual.

• After setup, and prior to public use, test the lasers to ensure they are functioning properly. Do

not use the product if any defect is detected.

• DO NOT point lasers at people or animals.

• DO NOT look into the laser aperture or laser beams.

• DO NOT point lasers into areas where people could be exposed to them.

• DO NOT point lasers at highly reflective surfaces such as windows, mirrors, and shiny metal.

Even laser reflections can be hazardous.

• Never point a laser at aircraft; this is a U.S. federal offense.

• Never point unterminated laser beams into the sky.

• Do not expose the output optic (aperture) to harsh cleaning chemicals.

• Do not use the laser if the housing is damaged, open, or if the optics appear damaged in any

way.

• Never open the laser housing. The high laser power levels inside of the protective housing can

start fires or burn skin, and will cause instant eye injury.

• Never leave this product running unattended.

• The operation of a Class 3R laser show is allowed only if the lasers are operated by a skilled

and well-trained professional, who is familiar with the data included in this manual.

• The legal requirements for using laser entertainment products vary from country to country.

The user is responsible for the legal requirements in the location/country of use.

CAUTION! Do not operate this device in ways not specified in this User Manual. Failure to

follow the instructions will void the warranty, may damage the product, or injure the user

or the audience.

CAUTION! This product cannot be discarded with household waste. Contact your local

waste management service for electronic disposal regulations in your area.

16

Before You Begin

GigBAR MOVE + ILS User Manual Rev. 8

Laser Safety Label Reproduction

Laser Exposure Warning

Laser Emission Data

As measured under IEC measurement conditions for classification.

Laser Compliance Statement

Complies with FDA performance standards for laser products except for deviations pursuant to Laser

Notice No. 56, dated May 08, 2019. No maintenance is required to keep this product in compliance with

laser performance standards.

LASER LIGHT AVOID DIRECT EYE EXPOSURE

Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1

Standard “For Safe Use of Lasers”, available from the Laser Institute of America: www.lia.org.

Many local governments, corporations, agencies, military, and others, require all lasers to be

used under the guidelines of ANSI Z136.1. Laser Display guidance can be obtained via the

International Laser Display Association: www.ilda.com.

Laser Classification Class 3R

Red Laser Medium LD/650 nm/80 mW

Green Laser Medium LD/520 nm/30 mW

Blue Laser Medium LD/450 nm/80 mW

Beam Diameter <5 mm at aperture

Pulse Data All pulses < 4 Hz (>0.25 sec)

Divergence (each beam) <2 mrad

Divergence (total light) <160 degrees

Laser Power of Each Beam from Aperture* <5 mW

*As measured under IEC measurement conditions for classification.

LASER APERTURE

MODEL: GIGBARMOVE+ILS

ITEM CODE: 10051948

FUSE: T 3.15 A, 250 V

POWER LINKING: 8 A (2 UNITS @ 120 V)

(4 UNITS @ 230 V)

ORIGIN: MADE IN CHINA

USA / CANADA

POWER: 100-125 VAC, 60 Hz

3 A, 250 W

WORLDWIDE

POWER: 100-240 VAC, 50/60 Hz

1.8-3 A, 248 W

THIS APPLIANCE MUST BE GROUNDED

CETTE UNITÉ DOIT ÊTRE RELIÉE À LA TERRE

USE ONLY FUSE OF SAME TYPE & RATING

N’UTILISER QUE DES FUSIBLES DU TYPE ET

DE L’AMPÉRAGE INDIQUÉ

NOT FOR HOUSEHOLD USE

IMPROPRE A L’USAGE DOMESTIQUE

DRY LOCATIONS

EMPLACEMENTS SECS

DISCONNECT POWER BEFORE SERVICING

DÉBRANCHER AVANT TOUT ENTRETIEN

FOR INDOOR USE ONLY

USAGE INTÉRIEUR UNIQUEMENT

WORLDWIDE HEADQUARTERS,

SUNRISE, FLORIDA USA

520/650/450nm

CW, <5mW

WARNING

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov

IEC/EN60825-1:2014



  !"#$%&'(

RoHS

Lorem ipsum

17

GigBAR MOVE + ILS User Manual Rev. 8

Introduction

2. Introduction

Product Overview

DMX

in/out

Fuse

holder

Power

in/out Menu

buttons

LED

display

Laser

Par 1

Spot 1

Microphone

Strobes (x4)

Back Panel View

Front Panel View

Derby 1 Derby 2

Spot 2

Par 2

Safety

loop

USB

port

18

Introduction

GigBAR MOVE + ILS User Manual Rev. 8

Product Dimensions

17.7 in

449 mm

43 in

1100 mm

2.5 in

63 mm 5.9 in

152 mm

6.7 in

169 mm

5 in

126 mm

19

GigBAR MOVE + ILS User Manual Rev. 8

Setup

3. Setup

AC Power

The GigBAR MOVE + ILS has an auto-ranging power supply, and it can work with an input voltage range

of 100 to 240 VAC, 50/60 Hz.

To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current

value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.

The listed current rating indicates the product’s average current draw under normal conditions.

Fuse Replacement

1. Disconnect the product from power.

2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.

3. Pry the fuse holder out of the housing.

4. Remove the blown fuse from the holder and replace with a fuse of the exact same type and rating.

5. Insert the fuse holder back in place and reconnect power.

Power Linking

The product provides power linking via the outlet located in the back of the product. See the diagram below

for further explanation.

Power-Linking Diagram

ILS Connection

ILS (Integrated Lighting System) provides 4 modes that synchronize with the GigBAR MOVE + ILS: Modes

1 and 3 synchronize with side 1 of the GigBAR MOVE + ILS, whereas modes 2 and 4 synchronize with

side 2 of the GigBAR MOVE + ILS. When linked, effects will sync with the most similar effect on the

selected side of the GigBAR MOVE + ILS: Kinta effects will sync with one of the kintas, moving heads will

sync with one of the moving heads, and wash effects will sync with one of the pars. Laser effects will sync

with the laser, and strobe effects will sync with the strobe effects regardless of ILS mode.

•

Always connect the product to a protected circuit (a circuit breaker or fuse). Make sure

the product has an appropriate electrical ground to avoid the risk of electrocution or fire

.

• To eliminate unnecessary wear and improve its lifespan, during periods of non-use

completely disconnect the product from power via breaker or by unplugging it.

Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the

rheostat or dimmer channel serves only as a 0 to 100% switch.

Disconnect the product from the power outlet before replacing the fuse.

Always replace a blown fuse with one of the same type and rating.

It is possible to power link up to 2 GigBAR MOVE + ILS products on 120 VAC or up to 4

GigBAR MOVE + ILS products on 230 VAC.

Safety cap

Spare fuse holder

(inside safety cap)

Installed fuse

(held by plastic clip)

1st Product 2nd Product 3rd Product

Power

Source

Additional

Products

20

Setup

GigBAR MOVE + ILS User Manual Rev. 8

Mounting

Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.

Orientation

The GigBAR MOVE + ILS must be mounted in a position that includes planning for safe laser usage. In

addition, make sure adequate ventilation is provided around the product.

Rigging

• Before deciding on a location for the product, always make sure there is easy access to the product

for maintenance and programming.

• Make sure that the structure or surface onto which you are mounting the product can support the

product’s weight (see the Technical Specifications)

• When mounting the product overhead, always use a safety cable. Mount the product securely to a

rigging point, such as an elevated platform or a truss.

• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.

• The bracket adjustment knobs allow for directional adjustment when aiming the product to the desired

angle. Only loosen or tighten the bracket knobs manually. Using tools could damage the knobs.

Mounting Diagram

Proper Usage

This product is for overhead mounting only. For safety purposes, Chauvet recommends mounting lighting

effect products on steady elevated platforms or sturdy overhead supports using suitable hanging clamps.

In all cases, use safety cables. Obtain appropriate mounting hardware from your lighting vendor.

International laser safety regulations require that laser products must be operated in the fashion

illustrated below, with a minimum of 3 meters (9.8 ft) of vertical separation between the floor and

the lowest laser light. Additionally, 3 meters of horizontal separation is required between laser light

and audience or other public spaces.

CAUTION! Use of controls, adjustments, or procedures other than THOSE specified IN

THIS USER MANUAL may result in hazardous radiation exposure.

Safety cable

(such as CH-05

from Chauvet)

Tripod mounting

insertion point

3 meters

21

GigBAR MOVE + ILS User Manual Rev. 8

Operation

4. Operation

This product is not designed for continual use. Make sure there are regular breaks during operation to

maximize the life of the lasers. Always disconnect the GigBAR MOVE + ILS from power when not in use.

Control Panel Operation

To access the control panel functions, use the four buttons located underneath the display. Please refer to

the Product Overview to see the button locations on the control panel.

Menu Map

Refer to the GigBAR MOVE + ILS product page on

www.chauvetdj.com

for the latest menu map.

Button Function

<MENU> Selects an operation mode or backs out of the current menu option

<UP> Navigates upwards through the menu list or increases a selected numeric value

<DOWN> Navigates downwards through the menu list or decreases a selected numeric value

<ENTER> Activates a menu option or selected value

Mode Programming Levels Description

AUTO

Program

Mix 1–4 Sets auto mixed effects show

Spots 1 Selects moving heads auto show

Strobe 1 Selects strobe auto show

Laser 1 Selects laser auto show

Derby 1 Selects derby auto show

Par 1 Selects pars auto show

S+SP 1 Selects strobe and moving heads auto show

L+SP 1 Selects laser and moving heads auto show

LS 1 Selects laser and strobe auto show

D+SP 1 Selects derby and moving heads auto show

DS 1 Selects derby and strobe auto show

DL 1 Selects derby and laser auto show

P+SP 1 Selects pars and moving heads auto show

PS 1 Selects pars and strobe auto show

PL 1 Selects pars and laser auto show

PD 1 Selects pars and derby auto show

PS+SP 1

Selects pars, strobe, and moving heads auto show

PL+SP 1

Selects pars, laser, and moving heads auto show

PLS 1

Selects pars, laser, and strobe auto show

PD+SP 1

Selects pars, derby, and moving heads auto show

PDS 1

Selects pars, derby, and strobe auto show

PDL 1

Selects pars, derby, and laser auto show

DLS+SP 1

Selects derby, laser, strobe, and moving heads auto show

PLS+SP 1

Selects pars, laser, strobe, and moving heads auto show

PDS+SP 1

Selects pars, derby, strobe, and moving heads auto show

PDL+SP 1

Selects pars, derby, laser, and moving heads auto show

PDLS 1

Selects pars, derby, laser, and strobe auto show

Mode Snap/Fade Selects the transition between auto programs

Speed 0–99 Sets automatic program speed

Spots XY Speed 0–99 Adjusts the pan and tilt speed of the spots

Dimmer 0–255 Adjusts the dimmer

Strobe 0–20 Selects the strobe

Program Time 1–255 (seconds) Sets the program time

Pars Color

Tri The auto program will only use the red, green, and

blue colors

Quad The auto program will only use the red, green, blue,

and amber colors

Hex The auto program will use all the colors

22

Operation

GigBAR MOVE + ILS User Manual Rev. 8

SOUND

Program

Mix 1–4 Sets mixed effects to sound mode

Spots 1 Sets moving heads to sound mode

Strobe 1 Sets strobe to sound mode

Laser 1 Sets laser to sound mode

Derby 1 Sets derby to sound mode

Par 1 Sets pars to sound mode

S+SP 1 Sets strobe and moving heads to sound mode

L+SP 1 Sets laser and moving heads to sound mode

LS 1 Sets laser and strobe to sound mode

D+SP 1 Sets derby and moving heads to sound mode

DS 1 Sets derby and strobe to sound mode

DL 1 Sets derby and laser to sound mode

P+SP 1 Sets pars and moving heads to sound mode

PS 1 Sets pars and strobe to sound mode

PL 1 Sets pars and laser to sound mode

PD 1 Sets pars and derby to sound mode

PS+SP 1

Sets pars, strobe, and moving heads

to sound mode

PL+SP 1

Sets pars, laser, and moving heads

to sound mode

PLS 1

Sets pars, laser, and strobe

to sound mode

PD+SP 1

Sets pars, derby, and moving heads

to sound mode

PDS 1

Sets pars, derby, and strobe

to sound mode

PDL 1

Sets pars, derby, and laser

to sound mode

DLS+SP 1

Sets derby, laser, strobe, and moving heads to sound mode

PLS+SP 1

Sets pars, laser, strobe, and moving heads to sound mode

PDS+SP 1

Sets pars, derby, strobe, and moving heads to sound mode

PDL+SP 1

Sets pars, derby, laser, and moving heads to sound mode

PDLS 1

Sets pars, derby, laser, and strobe

to sound mode

Sensitivity 0–99 Sets sound sensitivity

Spot Speed 0Activates sound-active moving heads

1–99 Adjusts moving head speed, slow to fast

Dimmer 0–255 Adjusts dimmer

Strobe 0–20 Selects the strobe

Program Time 1–255 (seconds) Sets the program time

Sound Lost

Slow The par, derby, laser, and strobe will stop on the last

setting. The moving heads, color/gobo will stop on

the last setting, and the movement will run slowly.

Freeze The entire bar will freeze on the last setting.

Blackout The entire bar will blackout.

Pars Color

Tri The auto program will only use the red, green, and

blue colors

Quad The auto program will only use the red, green, blue,

and amber colors

Hex The auto program will use all the colors

Manual

Mode

Par Red

0–255

Selects the Par color

Par Green

Par Blue

Par Amber

Par White

Par UV

Derby Red

Selects the Derby color

Derby Green

Derby Blue

Derby White

Mode Programming Levels Description

23

GigBAR MOVE + ILS User Manual Rev. 8

Operation

Manual

Mode

Derby Motor

0–255

Rotates the LED clockwise or counterclockwise

Laser

Turns the laser on and off manually

Flash Dimmer

Adjusts the dimmer of the white LED

Pan

Adjusts the pan angle

Tilt

Adjusts the tilt angle

Color Selects the color manually

Gobo Selects the gobo manually

Dimmer Adjusts the brightness

Shutter Adjusts the shutter

DMX DMX

3CH

Selects the DMX channel30CH

52CH

Address 001–510 Sets DMX starting address

Slave Sets the fixture on Slave mode

SETUP

RF

COMMON Enables control of the fixture using any RF remote

BIND Enables control of the GigBAR MOVE + ILS using

only the RF remote paired to the fixture

OFF Turns infrared off

RF Binding

Pairs an RF remote to a specific GigBAR MOVE + ILS

fixture

(Hold and press Blackout button on the RF remote)

FOOT

COMMON Enables control of the fixture using any footswitch

BIND Enables control of the GigBAR MOVE + ILS using

only the footswitch paired to the fixture

OFF Turns footswitch control off

FOOT Binding

Pairs a footswitch to a specific GigBAR MOVE + ILS

fixture

(Hold and press Blackout pedal on the footswitch)

DFI

OFF Disables DFI

RX Enables/disables receiving of DFI signal

TX Enables/disables transmitting of DFI signal

DFI CH 1–16 Selects DFI channel

Pan1 Reverse

ON Enables/disables Spot 1 pan reverse

OFF

Tilt1 Reverse ON Enables/disables Spot 1 tilt reverse

OFF

Pan2 Reverse

ON Enables/disables Spot 2 pan reverse

OFF

Tilt2 Reverse ON Enables/disables Spot 2 tilt reverse

OFF

RESET NO Resets to factory defaults

YES

• The DMX value will display in white if not receiving the DMX signal, and will display in

yellow if receiving the DMX signal.

• The menu display will turn off if there is no operation within 60 seconds.

• In DMX mode, the fixture will save the last settings when the DMX signal was lost. When

in Master/Slave mode, it will blackout when the DMX signal is lost.

Mode Programming Levels Description

24

Operation

GigBAR MOVE + ILS User Manual Rev. 8

Configuration (Standalone)

Set the product in one of the standalone modes to control without a DMX controller.

Automatic Mixed Effect Mode

To run the GigBAR MOVE + ILS in automatic mode, follow the instructions below.

1. Press <MENU> to view the main menu on the display.

2. Use <UP> or <DOWN> until AUTO is highlighted.

3. Press <ENTER>.

4. Use <UP> or <DOWN> to select Program.

5. Press <ENTER>.

6. Use <UP> or <DOWN> to select from the Auto Program options: Mix 1–4, Spots, Strobe, Laser,

Derby, Par, S+SP, L+SP, LS, D+SP, DS, DL, P+SP, PS, PL, PD, PS+SP, PL+SP, PLS, PD+SP,

PDS, PDL, DLS+SP, PLS+SP, PDS+SP, PDL+SP, or PDLS.

7. Press <ENTER>.

8. Use <UP> or <DOWN> to select Mode.

9. Press <ENTER>.

10. Use <UP> or <DOWN> to select between Snap (snap transition between programs) and Fade

(fading transition between programs).

11. Press <ENTER>.

12. Use <UP> or <DOWN> to select Speed.

13. Press <ENTER>.

14. Use <UP> or <DOWN> to select to adjust the program speed, from 0–99.

15. Press <ENTER>.

Sound-Active Mixed Effect Mode

To run the GigBAR MOVE + ILS in sound-active mode, do the following:

1. Press <MENU> to view the main menu on the display.

2. Use <UP> or <DOWN> until SOUND is selected.

3. Press <ENTER>.

4. Use <UP> or <DOWN> to select Program.

5. Press <ENTER>.

6. Use <UP> or <DOWN> to select from the Auto Program options: Mix 1–4, Spots, Strobe, Laser,

Derby, Par, S+SP, L+SP, LS, D+SP, DS, DL, P+SP, PS, PL, PD, PS+SP, PL+SP, PLS, PD+SP,

PDS, PDL, DLS+SP, PLS+SP, PDS+SP, PDL+SP, or PDLS.

7. Press <ENTER>.

Sound Sensitivity

To set the sound sensitivity on the GigBAR MOVE + ILS, follow the instructions below:

1. Press <MENU> to view the main menu on the display.

2. Use <UP> or <DOWN> until SOUND is selected.

3. Press <ENTER>.

4. Use <UP> or <DOWN> to select Sensitivity.

5. Press <ENTER>

6. Use <UP> or <DOWN> to set the sound sensitivity from 0–99.

7. Press <ENTER>.

Dimmer

To adjust the dimmer on the GigBAR MOVE + ILS, do the following:

1. Press <MENU> to view the main menu on the display.

2. Use <UP> or <DOWN> until AUTO or SOUND is selected.

3. Press <ENTER>.

4. Use <UP> or <DOWN> to select Dimmer.

5. Press <ENTER>.

6. Use <UP> or <DOWN> to set the dimmer from 0–255.

7. Press <ENTER>.

Never connect a product that is operating in any standalone mode to a DMX string

connected to a DMX controller. Products in standalone mode may transmit DMX signals

that could interfere with the DMX signals from the controller.

• The product will only respond to low frequencies of music (bass and drums).

• The laser will black out when in Sound-Active mode after 3 seconds of silence or noise

below the sensitivity setting.

25

GigBAR MOVE + ILS User Manual Rev. 8

Operation

Strobe

To set the strobe on the GigBAR MOVE + ILS, follow the instructions below:

1. Press <MENU> to view the main menu on the display.

2. Use <UP> or <DOWN> until AUTO or SOUND is selected.

3. Press <ENTER>.

4. Use <UP> or <DOWN> to select Strobe.

5. Press <ENTER>.

6. Use <UP> or <DOWN> to set the strobe from 0–20.

7. Press <ENTER>.

Program Time

To set the program time on the GigBAR MOVE + ILS, do the following:

1. Press <MENU> to view the main menu on the display.

2. Use <UP> or <DOWN> until AUTO or SOUND is selected.

3. Press <ENTER>.

4. Use <UP> or <DOWN> to select Program Time.

5. Press <ENTER>.

6. Use <UP> or <DOWN> to set the timer from 0–255 (seconds).

7. Press <ENTER>.

Pars Color

To set what color the pars will display when set to auto program, follow the instructions below:

1. Press <MENU> to view the main menu on the display.

2. Use <UP> or <DOWN> until AUTO or SOUND is selected.

3. Press <ENTER>.

4. Use <UP> or <DOWN> to select Pars Color.

5. Press <ENTER>.

6. Use <UP> or <DOWN> to select among Tri (use RGB), Quad (use RGBA), or Hex (use all colors).

7. Press <ENTER>.

Spot Speed

To manually control the moving head speed in sound-active mode on the GigBAR MOVE + ILS, do the

following:

1. Press <MENU> to view the main menu on the display.

2. Use <UP> or <DOWN> until SOUND is selected.

3. Press <ENTER>.

4. Use <UP> or <DOWN> to select Spot Speed.

5. Press <ENTER>.

6. Use <UP> or <DOWN> to set the speed from 0 (activates sound-active moving heads) or 1–99

(adjusts the speed of the moving head, from slow to fast).

7. Press <ENTER>.

Sound Lost

To set what the entire bar will do when sound is lost, follow the instructions below:

1. Press <MENU> to view the main menu on the display.

2. Use <UP> or <DOWN> until SOUND is selected.

3. Press <ENTER>.

4. Use <UP> or <DOWN> to select Sound Lost.

5. Press <ENTER>.

6. Use <UP> or <DOWN> to choose from Slow (the par, derby, laser, and strobe will stop on the last

setting, whereas the moving heads and color/gobo will stop on the last setting, and the movement

will run slowly), Freeze (the entire bar will freeze on the last setting), or Blackout (the entire bar

will blackout).

7. Press <ENTER>.

La page charge ...

CHAUVET DJ GigBAR Move + ILS Manuel utilisateur

CHAUVET DJ GigBAR Move + ILS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents