DRAKE VM2050 Manuel utilisateur

Marque: DRAKE

Modèle: VM2050

Catégorie: Modulateur

Taper: Manuel utilisateur

Ce manuel convient également à

Instruction Manual

® is a registered trademark of the R.L. Drake Holdings LLC

Printed in China.

VM2050/VM2551

Commercial Video Modulator

(For use in NTSC systems)

Rev: 20151111

1002412A/1002423A

VM SERIES VIDEO MODULATOR

1. Read Instrucons—All the safety and operang instrucons should be read before

the product is operated.

2. Retain Instrucons—The safety and operang instrucons should be retained for

future reference.

3. Heed Warnings—All warnings on the product and in the operang instrucons

should be adhered to.

4. Follow Instrucons—All operang and use instrucons should be followed.

5. Cleaning—Unplug this product from the wall outlet before cleaning. Do not use

liquid cleaners or aerosol cleansers. Use a damp cloth for cleaning.

6. Aachments—Do not use aachments that are not recommended by the product

manufacturer as they may cause hazards.

7. Water and Moisture—Do not use this product near water—for example, near a

bathtub, wash bowl, kitchen sink or laundry tub; in a wet basement; or near a swim-

ming pool; and the like.

8. Accessories—Do not place this product on an unstable cart, stand, tripod, bracket,

or table. The product may fall, causing serious injury to a child or adult, and serious

damage to the product. Use only with a cart, stand, tripod, bracket, or table recom-

mended by the manufacturer, or sold with the product. Any mounng of the product

should follow the manufacturer’s instrucons, and should use a mounng accessory

recommended by the manufacturer.

9. A product and cart combinaon should be moved with care. Quick stops, excessive

force, and uneven surfaces may cause the product and cart combinaon to overturn.

10. Venlaon—Slots and openings in the cabinet are provided for venlaon and to

ensure reliable operaon of the product and to protect it from overheang, and these

openings must not be blocked or covered. The openings should never be blocked by

placing the product on a bed, sofa, rug, or similar surface. This product should not be

placed in a built-in installaon such as bookcase or rack unless proper venlaon is

provided or the manufacturer’s instrucons have been adhered to.

11. Power Sources—This product should be operated only from the type of power

source indicated on the marking label. If you are not sure of the type of power sup-

plied to your home, consult your product dealer or local power company. For products

intended to operate from baery power, or other sources, refer to the operang

instrucons.

12. Grounding or Polarizaon—This product may be equipped with a polarized

alternangcurrent line plug (a plug having one blade wider than the other). This plug

will t into the power outlet only one way. This is a safety feature. If you are unable to

insert the plug fully into the outlet, try reversing the plug. If the plug should sll fail to

t, contact your electrician to replace your obsolete outlet. Do not defeat the safety

purpose of the polarized plug. Alternate Warnings—If this product is equipped with

a three-wire grounding-type plug, a plug having a third (grounding) pin, the plug will

only t into a grounding-type power outlet. This is a safety feature. If you are unable

to insert the plug into the outlet, contact your electrician to replace your obsolete

outlet. Do not defeat the safety purpose of the grounding-type plug.

13. Power-Cord Protecon—Power-supply cords should be routed so that they are

not likely to be walked on or pinched by items placed upon or against them, paying

parcular aenon to cords at plugs, convenience receptacles, and the point where

they exit from the product.

14. Outdoor Antenna Grounding—If an outside antenna or cable system is connect-

ed to the product, be sure the antenna or cable system is grounded so as to provide

some protecon against voltage surges and built-up stac charges. Arcle 810 of the

Naonal Electrical Code, ANSI/NFPA 70, provides informaon with regard to proper

grounding of the mast and supporng structure, grounding of the lead-in wire to an

antenna discharge unit, size of grounding conductors, locaon of antenna-discharge

unit, connecon to grounding electrodes, and requirements for the grounding elec-

trode. See Figure A.

15. Lightning—For added protecon for this product during a lightning storm, or when

it is le unaended and unused for long periods of me, unplug it from the wall outlet

and disconnect the antenna or cable system. This will prevent damage to the product

due to lightning and power-line surges.

16. Power Lines—An outside antenna system should not be located in the vicinity of

overhead power lines, other electric light or power circuits, where it can fall into such

power lines or circuits.

17. Overloading—Do not overload wall outlets, extension cords, or integral conve-

nience receptacles as this can result in a risk of re or electric shock.

18. Object and Liquid Entry—Never push objects of any kind into this product through

openings as they may touch dangerous voltage points or short-out parts that could

result in a re or electric shock. Never spill liquid of any kind on the product.

19. Servicing—Do not aempt to service this product yourself as opening or removing

covers may expose you to dangerous voltage or other hazards. Refer all servicing to

qualied service personnel.

20. Damage Requiring Service—Unplug this product from the wall outlet and refer

servicing to qualied service personnel under the following condions:

a. When the power-supply cord or plug is damaged,

b. If liquid has been spilled, or objects have fallen into the product,

c. If the product has been exposed to rain or water,

d. If the product does not operate normally by following the operang instrucons.

Adjust only those controls that are covered by the operang instrucons as an im-

proper adjustment of other controls may result in damage and will oen require ex-

tensive work by a qualied technician to restore the product to its normal operaon,

e. If the product has been dropped or damaged in any way, and

f. When the product exhibits a disnct change in performance—this indicates a need

for service.

21. Replacement Parts—When replacement parts are required, be sure the service

technician has used replacement parts specied by the manufacturer or have the

same characteriscs as the original part. Unauthorized substutes may result in re,

electric shock or other hazards.

22. Safety Check—Upon compleon of any service or repairs to this product, ask the

service technician to perform safety checks to determine that the product is in proper

operang condion.

23. Wall or Ceiling Mounng—The product should be mounted to a wall or ceiling

only as recommended by the manufacturer.

24. Heat—The product should be situated away from heat sources such as radiators,

heat registers, stoves, or other products (including ampliers) that produce heat.

NOTE TO CATV SYSTEM INSTALLERS:

THIS REMINDER IS PROVIDED TO CALL THE CATV

SYSTEM INSTALLER’S ATTENTION TO ARTICLE 820 - 40

OF THE NEC WHICH PROVIDES GUIDELINES FOR PROPER

GROUNDING AND, IN PARTICULAR, SPECIFIES THAT

THE CABLE GROUND SHALL BE CONNECTED TO THE

GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO

THE POINT OF CABLE ENTRY AS PRACTICAL.

FIGURE A

Example of antenna grounding as per Naonal Electrical Code, ANSI/NFPA 70

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING

CONDUCTORS

(NEC SECTION 810-21)

POWER SERVICE GROUNDING ELECTRODE

SYSTEM (NEC ART 250, PART H)

ELECTRIC

SERVICE

EQUIPMENT

GROUND CLAMPS

GROUND CLAMP

NEC - NATIONAL ELECTRIC CODE

WARNING: TO PREVENT FIRE OR

ELECTRICAL SHOCK DO NOT

EXPOSE TO RAIN OR MOISTURE

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE POWER SUPPLY COVERS

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED PERSONNEL

! CAUTION !

CAUTION STATEMENT

An appliance and cart combinaon should be moved with care. Quick stops, excessive

force and uneven surfaces may cause the appliance and cart combinaon to overturn.

The exclamaon point within an equilateral triangle is intended to alert the user to

the presence of important operang and maintenance (servicing) instrucons in the

literature accompanying the appliance.

The lightning ash with arrow head symbol, within an equilateral triangle, is intended to

alert the user to the presence of uninsulated “dangerous voltage” within the product’s

enclosure that may be of sucient magnitude to constute a risk of electric shock to

persons.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE. DO NOT OPEN THE CABINET, REFER

SERVICING TO QUALIFIED PERSONNEL ONLY.

CAUTION:

TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN

EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN

BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

Important Safety Instructions

Importantes De Sécurité

1. Lire les direcves—Toutes les direcves de sécurité et d’ulisaon devraient être

lues avant de mere l’appareil en opéraon.

2. Conserver les direcves—Les direcves de sécurité et d’ulisaon devraient être

conservées pour consultaon future.

3. Tenir compte des averssements—Tous les averssements apparaissant sur l’appar-

eil et dans les consignes d’ulisaon devraient être respectés.

4. Suivre les direcves—Toutes les direcves d’opéraon et d’ulisaon devraient

être suivies.

5. Neoyage—Débrancher l’appareil de la prise électrique murale avant le neoyage.

Ne pas uliser de neoyants liquides ou aérosols. Employer un linge humide pour le

neoyage.

6. Fixaon—Ne pas uliser d’autres xaons que celles recommandées par le manu-

facturier; elles pourraient être source de dangers.

7. Eau et humidité—Ne pas uliser cet appareil près de l’eau. Par exemple, près d’une

baignoire, d’un bac de lavage, d’un évier de cuisine ou d’une cuvee de lessivage; dans

un sous-sol humide; ou à proximité d’une piscine; et autres environnements similaires.

8. Accessoires—Ne pas installer cet appareil sur un chariot, un socle, un trépied, un

support ou une table instables. L’appareil pourrait tomber, entraînant des blessures

graves à un enfant ou à un adulte, et des dommages importants à l’appareil. Employer

seulement avec un chariot, un socle, un trépied, un support, ou une table recom-

mandés par le fabricant ou vendu avec l’appareil. Toute installaon de l’appareil

devrait être conforme aux direcves du manufacturier et devrait uliser des acces-

soires d’installaon recommandés par celui-ci.

9. Un chariot supportant l’appareil devrait être déplacé avec précauon. Les arrêts

brusques, la force excessive et les surfaces inégales peuvent renverser le chariot.

10. Venlaon—Des fentes et ouvertures dans le châssis sont prévues pour la

venlaon de l’appareil, pour en assurer la abilité d’opéraon et le protéger contre

la surchaue. Ces ouvertures ne doivent pas être bloquées ou recouvertes. Ces

ouvertures ne devraient jamais être bloquées en plaçant l’appareil sur un lit, un sofa,

une couverture, ou une surface semblable. Cet appareil ne devrait pas être installé

dans un meuble encastré comme une bibliothèque ou une étagère à moins de lui

fournir une venlaon adéquate ou que l’installaon soit conforme aux direcves du

manufacturier.

11. Sources d’alimentaon électrique—Cet appareil devrait être ulisé seulement

avec le type d’alimentaon électrique inscrite sur l’équee. Si vous n’êtes pas certain

du type d’alimentaon électrique fourni à votre maison, consultez le vendeur de l’ap-

pareil ou l’entreprises d’énergie locale. Pour des appareils alimentés par une baerie

ou d’autres sources, se référer aux consignes d’ulisaon.

12. Mise à la terre ou Polarisaon—Cet appareil est équipé avec un cordon d’ali-

mentaon à trois ls. Il est a brancher sur une prise ayant un connecteur a la terre.

Assurez-vous que la connecon a la terre ne manque pas.

13. Protecon du cordon d’alimentaon—Les cordons d’alimentaon devraient être

disposés de façon à ce qu’on ne puisse marcher dessus ou qu’ils soient suscepbles

d’être coincés par des arcles placés sur ou contre eux. Une aenon parculière doit

être portée aux ches, prises de courant, et aux points où ils sortent de l’appareil.

14. Mise à la terre de l’antenne extérieure—Si un système extérieur d’antenne ou de

câble est relié à l’appareil, s’assurer que le système d’antenne ou de câble est muni

d’une mise à la terre an de fournir une certaine protecon contre les surtensions et

les charges d’électricité staque. L’arcle 810 du code électrique naonal, ANSI/NFPA

70, fournit l’informaon nécessaire en ce qui concerne la mise à la terre appropriée du

mât et de la structure porteuse, la mise à la terre du câble de connexion à une unité

de décharge d’antenne, le calibre des conducteurs de mise à la terre, la locaon de

l’unité de décharge d’antenne, le raccordement aux électrodes de mise à la terre et les

spécicaons pour les électrodes de mise à la terre.

Voir la gure A.

15. Foudre—Pour une protecon supplémentaire de cet appareil pendant un orage

électrique, ou quand il est laissé sans surveillance et inulisé pendant de longues

périodes, le débrancher de la prise électrique murale et déconnecter le système

d’antenne ou de câble. Ceci préviendra les dommages à l’appareil dus à la foudre et

aux surtensions.

16. Lignes électriques—Un système d’antenne extérieur ne devrait pas être situé à

proximité de lignes électriques aériennes ou de tout autre circuit électrique, où il

pourrait tomber sur de tels circuits ou lignes électriques. Lors de l’installaon d’un

système d’antenne extérieur, d’extrêmes précauons devraient être prises an de

prévenir tout contact avec des lignes ou circuits électriques. Entrer en contact avec de

tels circuits ou lignes électriques pourrait être fatal.

17. Surcharge—Ne pas surcharger les prises de courant murales, les rallonges élec-

triques ou les prises de courant intégrées. Un risque d’incendie ou de choc électrique

pourrait résulter d’une telle surcharge.

18. Inseron d’objet ou de liquide—Ne jamais insérer d’objet par les ouvertures de

cet appareil. Il pourrait toucher des points de voltage dangereux ou court-circuiter des

pièces, ce qui pourrait résulter en incendie ou en choc électrique. Ne jamais verser de

liquide sur l’appareil.

19. Entreen—Ne pas essayer de faire soi-même l’entreen de cet appareil. En ouvrir

ou en rerer les couvercles pourrait vous exposer à des voltages dangereux ou à d’au-

tres dangers. Coner tout entreen à un personnel de service qualié.

20. Dommage exigeant un entreen—Débrancher cet appareil de la prise de courant

électrique et coner l’entreen au personnel de service qualié dans les éventualités

suivantes:

a. Quand le cordon d’alimentaon ou sa che sont endommagés,

b. Si des objets sont tombés dans l’appareil, ou si du liquide y a été renversé,

c. Si l’appareil a été exposé à la pluie ou à l’eau,

d. Si l’appareil ne fonconne pas normalement en suivant les consignes d’ulisaon.

Ajuster seulement les commandes qui sont menonnées dans le guide d’opéraon.

Un mauvais ajustement des autres commandes pourrait causer des dommages à

l’appareil et souvent exiger un travail supplémentaire de la part d’un technicien

qualié pour remere l’appareil en état normal d’opéraon.

e. Si l’appareil a été échappé ou endommagé de n’importe quelle façon, et

f. Quand l’appareil montre un changement notable de performance – ceci indique

qu’un entreen est nécessaire.

21. Pièces de rechange—Si des pièces de rechange sont nécessaires, s’assurer que le

technicien de service a employé des pièces de rechange spéciques du manufacturier

ou ayant les mêmes caractérisques que les pièces originales. L’ulisaon de pièces

de rechange non autorisées pourrait résulter en incendie, choc électrique ou autres

dangers.

22. Véricaon de sécurité—À la suite de toute réparaon ou entreen de cet appar

eil, demander au technicien de service d’exécuter des véricaons de sécurité an de

s’assurer que l’appareil est en condion normale de fonconnement.

23. Montage au mur ou au plafond—L’appareil ne devrait être monté au mur ou au

plafond qu’uniquement de la façon recommandée par le manufacturier.

24. Chaleur—L’appareil devrait être situé loin de sources de chaleur telles que des

radiateurs, des registres de chaleur, des fourneaux, ou d’autres appareils (y compris

amplicateurs) produisant de la chaleur.

NOTE AUX INSTALLATEURS DE SYSTÈME DE CATV:

CE RAPPEL EST FOURNI POUR PORTER À L’ATTENTION DES

INSTALLATEURS DE SYSTÈME DE CATV, L’ARTICLE 820 - 40 DU

NEC QUI DONNE DES DIRECTIVES POUR UNE MISE À LA TERRE

APPROPRIÉE ET, EN PARTICULIER, SPÉCIFIE QUE LE CÂBLE DE

MISE À LA TERRE DEVRAIT ÊTRE RACCORDÉ AU SYSTÈME DE

MISE À LA TERRE DU BÂTIMENT LE PLUS PRÈS POSSIBLE DE

L’ENTRÉE DU CÂBLE.

FIGURE A

Exemple de mise à la terre d’antenne selon le Code Électrique Naonal, ANSI/NFPA 70

ANTENNA

LEAD IN

WIRE

UNITÉ DE DÉCHARCHE D’ANTENNE

(NEC SECTION 810-20)

CONDUCTEURS DE MISE À LA TERRE

(NEC SECTION 810-21)

SYSTÈME DE MISE À LA TERRE DU BÂTIMENT

(NEC ART 250, PART H)

APPAREILS

ÉLECTRIQUES

DE SERVICE

ATTACHES DE

MISE À LA TERRE

ATTACHES DE

MISE À LA TERRE

NEC - CODE ÉLECTRIQUE NATIONAL

AVERTISSEMENT: AFIN D’ÉVITER TOUT RISQUE D’INCENDIE

OU D’ÉLECTROCUTION, NE PAS EXPOSER CET APPAREIL À LA

PLUIE OU À L’HUMIDITÉ.

RISQUE DE CHOC ELECTRIQUE -

NE PAS OUVRIR

ATTENTION: POUR RÉDUIRE LE RISQUE D’ÉLECTROCUTION, NE PAS

ENLEVER LE DOS DE L’APPAREIL NI OUVRIR LE BOÎTIER. AUCUNE PIÈCE N’EST

RÉPARABLE PAR L’UTILISATEUR À L’INTÉRIEUR. SE RÉFÉRER UNIQUEMENT À

DES TECHNICIENS QUALIFIÉS POUR L’ENTRETIEN.

! AVERTISSEMENT !

Une combinaison de l’appareil et chariot doit être déplacé avec précauon. Des arrêts

brusques, une force excessive et des surfaces inégales peuvent causer la combinaison

de l’appareil et le chariot.

Le point d’exclamaon à l’intérieur d’un triangle équilatéral est desné à alerter

l’ulisateur sur la présence d’opéraons d’entreen importantes au sujet desquelles des

renseignements se trouvent dans le manuel d’instrucons.

Le symbole de l’éclair à l’intérieur d’un triangle équilatéral est desné à alerter

l’ulisateur sur la présence d’une “tension dangereuse” non isolée dans le boîer du

produit. cee tension est susante pour provoquer l’électrocuon de personnes.

ATTENTION DÉCLARATION

AVERTISSEMENT:

AFIN D’ÉVITER TOUT RISQUE D’INCENDIE OU D’ÉLECTROCUTION, NE PAS

EXPOSER CET APPAREIL À LA PLUIE OU À L’HUMIDITÉ. NE PAS OUVRIR LE

BOÎTIER, CONFIER TOUS TRAVAUX À DU PERSONNEL TECHNIQUE QUALIFIÉ.

CAUTION:

POUR PREVENIR LES CHOCS ELECTRIQUES, NE PAS UTILISER CETTE FICHE

POLARISEE AVEC UN PROLONGATEUR, UNE PRISE DE COURANT OU UNE

AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A

FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

Table of Contents / Description / Specifications

2 Caution Statements

2 Important Safety Instructions

4 Table of Contents / Description / Speciﬁcations

5 Front/Rear Panel Controls and Indicators

TABLE OF CONTENTS

The R.L Drake VM2050 and VM2550 Video Modulators are high quality, vesgial

sideband units with synthesized visual and aural carriers. They are designed to accept

NTSC video and audio baseband signals from a satellite receiver or similar equipment.

Front panel video and audio level controls with accompanying modulaon

indicators permit easy setup of the proper modulaon levels. The A/V rao and

RF output level controls are also provided on the front panel. A rear panel EAS

alternate IF input is also provided.

Synthesized operaon provides complete frequency agility, allowing front panel

selecon of any standard CATV channel from 2 to 78 (VM2551) and T7 to 78

(VM2050) . FCC required osets for aeronaucal channels are automacally

provided for each channel that requires an oset. For special applicaons, IRC or

HRC CATV frequencies or o-air broadcast frequencies can be selected from the

front panel.

A high quality IF SAW lter with FCC predistoron eliminates adjacent channel

interference and provides opmum delay characteriscs.

A manual or auto-switching alternate IF input, labeled EAS input, is provided for

connecon of an Emergency Alert System 44 MHz IF signal. When the EAS IF signal

appears at the EAS input, the main video and audio modulated IF is replaced by

the EAS input signal.

The EAS/Alternate IF feature allows a choice between manual and automac

selecon of the EAS/ALT IF input signal. This is done through a 3 posion terminal

strip on the rear of the unit. In the manual mode the EAS/ALT IF feature is

acvated by a contact closure switch, which completes a ground connecon. In

the automac mode, two posions on the terminal strip are jumpered together

enabling an automac detecon circuit in the unit. When an EAS/ALT IF signal is

routed to the EAS/ALT port the unit automacally switches to that alternate signal.

DESCRIPTION

SPECIFICATIONS - VM2050 / VM2551

6 Operation

7 Adjustments

8 Channel Assignments

VIDEO INPUT

Connector:

Impedance:

Return Loss:

Video Input Level:

Signal-to-Noise Rao:

Dierenal Gain:

Dierental Phase:

Over-modulaon Indicator:

L/C Delay:

“F” Female

75 Ω

18 dB

0.7 volt Peak-to-Peak

58 dB

2.0%

1.0 degree

87 to 92%

Per FCC Requirements

RF OUTPUT

Connector:

Impedance:

Return Loss:

Channel Modes:

Power Level Range:

Video Flatness:

Carrier-to-Noise:

Broadband Noise:

Spurious Outputs:

Aural/Visual Carrier Rao:

“F” Female

75 Ω

12 dB

CATV (STD,IRC,HRC) UHF, VHF

(SUB VM2050 only)

+50 to +60 dBmV (in 0.2 dB increments)

fv-0.5 to fv+4.2 MHz : 1.5 dB p/v

-63 dB

-77 dBc

-63 dBc

-15 ± 5 dB

GENERAL

AC Power:

Fuse:

Temperature Range:

Dimensions (WxDxH):

Weight:

117 VAC ± 10%, 60 Hz, 23W max

0.4A Type T 250 V

32 to 122 °F (0 to 50 °C)

19.0 x 14.25 x 1.75 in

(482.6 x 361.95 x 44.45 mm)

7 lbs. (3.18 kg)

MONO AUDIO

Connector:

Input Impedance:

Input Level:

Frequency Range:

Frequency Response:

Total Harmonic Distoron:

Signal-to-Noise Rao:

Over-modulaon Threshold:

RCA

Greater than 10k Ω, unbalanced

0.5 to 4.0 volt Peak-to-Peak

50 Hz to 15 kHz

± 0.5 dB

1% @ 25 kHz deviaon

59 dB

25 ± 2 kHz peak deviaon

Input/Output Connector:

Aural Frequency:

Visual Frequency:

“F” Female

41.25 MHz

45.75 MHz

Composite IF Output

Aural:

Visual:

+20 dBmV

+35 dBmV

Input/Output Impedance:

Input/Output Return Loss:

75 Ω

16/15 dB

EAS/Alternave IF

Connector:

Input Level:

“F” Female

+30 dBmV @ 45.75 MHz

Switch Isolaon: Greater than 60dB

VM SERIES VIDEO MODULATOR

Front and Rear Panel Controls and Indicators

Operating Controls

All operating controls and indicators for the modulator are located on, or are accesible from the front panel.

[1] EAS/ALT INDICATOR: Lights Red when EAS/ALT is active.

[2] VIDEO OVERMODULATION LED: Lights when modulation is above 87.5%

[3] VIDEO MODULATION LEVEL: Adjusts percentage of modulation.

[4] AURAL-TO-VISUAL CARRIER RATIO: Controls amplitude of aural RF carrier relative to visual RF carrier.

[5] AUDIO MODULATION LEVEL: Adjusts aural carrier modulation.

[6] AUDIO OVERMODULATION LED: Lights when peak deviation of aural carrier is over 25 kHz.

[7] DISPLAY MODE BUTTON: Used to scroll through channel conﬁguration, output level and modes.

[8] CHANNEL, CHANNEL CONFIGURATION/OUTPUT LEVEL DISPLAY

[9] UP/DOWN BUTTONS: Used to scroll through the channel, channel conﬁguration and output level modes.

[10] ENTER BUTTON: Evokes the current settings in the channel/output display when depressed.

[11] STEREO INDICATOR: Not Used

Note: All connections to the unit are made at the rear panel.

[1] RF OUTPUT: +60dBmV

[2] IF INPUT: +35 dBmV IF Input

[3] EAS/ALT IF INPUT: Emergency Alert or Alternate IF Input

[4] IF OUT: +35 dBmV IF Outpout (See note #8 below)

[5] EAS/ALT IF TERMINAL: EAS/ALT IF mode selection (see page 7)

[6] AUDIO INPUT: Audio input (standard)

[7] VIDEO INPUT: 1 Volt PP video input

[8] IF LOOP CABLE: The IF loop cable (supplied) must be installed to provide RF continuity. The modulator will not have

an RF output without the IF loop installed.

[1] [6] [5] [4] [3] [2] [7] [8] [9]

Figure 1 - Front Panel

[11] [12]

[1] [2] [3] [4] [6] [7]

[5]

Figure 2 - Rear Panel

[8]

Operation6

Opera n

Display Mode

This bu

on scrolls through the selec of Channel, Channel Conﬁgura Output Level mode in this order.

The res

g state (default) of the modulator’s display mode is the channel number.

Channel

The output channel is selected by pressing the UP or DN bu on when in the channel display mode.

The LED display will blink indica

g a transi state.

The actual channel is not changed un

the ENTER bu on is pressed.

If the ENTER bu

on is not pressed, the display will return to res g state a er 30 seconds.

Pressing and holding the UP or DN bu

on will allow for faster scrolling of channel.

All internal a

enuators are temporarily set for maximum a enua during channel change (output is muted).

Channel Conﬁgura

The Channel Conﬁgura is changed by pressing the UP or DN bu on when in the Channel Conﬁgura display mode.

The LED display will blink indica

g a transi state.

The channel conﬁgura

is not changed un the ENTER bu on is pressed.

If the ENTER bu

on is not pressed, the display will return to res g state a er 30 seconds.

If the mode is to be changed and it is not a valid mode for the exis

g channel, when the ENTER bu on is pressed, the new

mode will be selected, and the channel will default to channel-2.

The available Channel Conﬁgura

are as follows:

C = Standard (default from factory)

I = IRC

H = HRC

U = Broadcast VHF/UHF

Error

The Display will show a ﬂashing "EE1" if the PLL1 is not locked.

The Display will show a ﬂashing "EE2" if the PLL2 is not locked.

The Display will show a ﬂashing "EE3" if both PLL1 and PLL2 are not locked.

All internal a

enuators are automa cally set for maximum a enua in any of the above condi (output is muted).

Please contact our Service Department should any of these errors condi

occur.

VM2050 (only) Subchannel display in standard

and

Adjustments

VIDEO LEVEL: With the intended signal source connected and a representa ve video program present turn the Video

Level Adjust control clockwise un

the Video Overmodula light just ﬂashes, then back oﬀ slightly.

Alterna

vely, while watching the picture on a good TV monitor, adjust the control to the highest (clockwise)

level that does NOT cause the highlights (white por

of the picture) to become “washed out”.

AUDIO LEVEL: Turn the Audio Level Adjust control clockwise un the Audio Overmodula light just ﬂashes slightly on

the loudest peaks of the audio program material.

OUTPUT LEVEL: The Output Level is adjusted by pressing the UP or DN bu

on when in the Output Level display mode.

The LED display will blink indica

g a transi on state. The output level is not changed un the ENTER

on is pressed. If the ENTER bu on is not pressed, the display will return to its res g state a er 30

seconds. Pressing and holding the UP or DN bu

on will allow for faster scrolling. The Level increments in

0.2 dB steps. Output level accuracy is typically +/- 1 dB of display, +/- 2 dB worst case.

A/V CARRIER RATIO: To adjust the aural-to-visual carrier ra

o, tune the RF indicator device to the aural carrier frequency

and adjust the Aural Carrier control to obtain the desired aural carrier level. Recommended ra

-15 dB.

EAS/ALT IF:

AUTOMATIC: Connect a jumper to the terminal strip auto posi

EAS will switch on when

a +30 dBmV EAS IF signal is detected.

MANUAL: EAS is ac

ve with a ground connec on the manual posi of the terminal strip.

Channel Assignments

HRC

72.00

54.00

60.00

66.00

78.00

84.00

174.00

180.00

186.00

192.00

198.00

204.00

210.00

120.00

126.00

132.00

138.00

144.00

150.00

156.00

162.00

168.00

216.00

222.00

228.00

234.00

240.00

246.00

252.00

258.00

264.00

270.00

276.00

282.00

288.00

294.00

300.00

306.00

312.00

318.00

324.00

330.00

336.00

342.00

348.00

354.00

360.00

366.00

372.00

378.00

384.00

390.00

396.00

402.00

408.00

414.00

420.00

426.00

432.00

438.00

444.00

450.00

456.00

462.00

468.00

474.00

480.00

486.00

492.00

498.00

504.00

510.00

516.00

522.00

528.00

534.00

540.00

546.00

EIA CH# /

Output Channel

Switch Setting

Visual Carrier

Frequency (MHz)

STD IRC

N/A

55.25

61.25

67.25

77.25

83.25

175.25

181.25

187.25

193.25

199.25

205.25

211.25

121.2625

127.2625

133.2625

139.25

145.25

151.25

157.25

163.25

169.25

217.25

223.2625

229.2625

235.2625

241.2625

247.2625

253.2625

259.2625

265.2625

271.2625

277.2625

283.2625

289.2625

295.2625

301.2625

307.2625

313.2625

319.2625

325.2625

331.275

337.2625

343.2625

349.2625

355.2625

361.2625

367.2625

373.2625

379.2625

385.2625

391.2625

397.2625

403.25

409.25

415.25

421.25

427.25

433.25

439.25

445.25

451.25

457.25

463.25

469.25

475.25

481.25

487.25

73.25

79.25

85.25

TABLE 1:

CATV

493.25

499.25

505.25

511.25

517.25

523.25

529.25

535.25

541.25

547.25

T7 7

T8 13

T9 19

T10 25

T11 31

T12 37

T13 43

T14 49

Sub Band Channels

Channel Standard Video

9 Channel Assignments, continued

Visual Carrier

Frequency (MHz)

471.25

477.25

483.24

489.25

495.25

501.25

507.25

513.25

519.25

525.25

531.25

537.25

543.25

549.25

UHF BROADCAST CHANNELSUHF BROADCAST CHANNELS

UHF BROADCAST CHANNELS

Channel Number

55.25

61.25

67.25

77.25

83.25

175.25

181.25

187.25

193.25

199.25

205.25

211.25

Visual Carrier

Frequency (MHz)

VHF BROADCAST CHANNELSVHF BROADCAST CHANNELS

VHF BROADCAST CHANNELS

Channel Number

TABLE 2:

BROADCAST TV

10 Repairs and Returns

A Return Material Authorization (RMA) Number is required on ALL PRODUCT RETURNS (regardless of whether the

product is being returned for repair or for credit). Product that is received at the factory without an RMA Number will be

returned to the sender, unopened.

RMA Numbers must be used when returning product for credit or repair. Use of RMA Numbers will ensure efcient

processing. When needing to return your product to R.L. Drake Holdings, LLC., please follow these simple steps listed

below (in the order that they appear).

Service

1. Contact R.L. Drake Holdings, LLC.’s Service Department

in one of three ways:

Phone: 732-313-4256

Email: [email protected]

Fax: 732-679-4022

2. Request from Drake Service a copy of the Product Return

Authorization Form.

3. Complete the Product Return Authorization Form fully.

4. Return the completed Product Return Authorization Form

to the Drake Service Department using one of the contact

methods listed in Step 1.

5. After completing Steps 1 through 4, an RMA Number will

be assigned to you.

6. Securely pack the product and mark the box with your

RMA Number. If shipping multiple boxes, all boxes must

be marked with the RMA Number. Place the RMA Number

near the return address in large, bold print (approx. 2” in

height).

1. Contact R.L. Drake Holdings, LLC.’s Service Department

in one of three ways:

Phone: 937-746-6990

Email: [email protected]

Fax: 937-806-1510

2. Request from Drake Service a copy of the Product Return

Authorization Form.

3. Complete the Product Return Authorization Form fully.

4. Return the completed Product Return Authorization Form

to the Drake Service Department using one of the contact

methods listed in Step 1.

5. After completing Steps 1 through 4, an RMA Number will

be assigned to you.

6. Securely pack the product in its original undamaged box

(returning the product without its original packaging in

good, new condition may cause the incursion of additional

fees). Pack this box within another shipping container or

box. Mark the shipping box or container with your RMA

Number. Place the RMA Number near the return address

in large, bold print (approx. 2” in height).

Ship your “CREDIT RETURNS ONLY” return to:

R.L. Drake Holdings, LLC.

Attn: Product Credit Returns

One Jake Brown Road

Old Bridge, NJ 08857

Ship your “SERVICE REPAIR ONLY” return to:

R.L. Drake Holdings, LLC.

Attn: Product Service Returns

One Jake Brown Road

Old Bridge, NJ 08857

SERVICE REPAIRS ONLY CREDIT RETURNS ONLY

*NOTE: All Credit Returns are subject to a 15% Restock Fee

*NOTE: All shipments are to be PRE-PAID by the sender. NO COD’s will be accepted.

IF YOU NEED TECHNICAL HELP

Call our Customer Service/Technical Support line at +1 (937) 746-6990 weekdays between 8:00 A.M. and 4:00 P.M. Eastern Standard

Time. Please have the unit’s serial number available. We will also need to know the specics of any other equipment connected to the

unit. When calling, please have the unit up and running, near the phone if possible. Our technician(s) will likely ask certain questions to

aid in diagnosis of the problem. Also, have a voltmeter handy, if at all possible.

DRAKE also provides technical assistance by

Email: [email protected]

Fax: (937) 806-1510

Many of the products that are sent to us for repair are in perfect working order when we receive them. For these units, there is a

standard checkout fee that will be charged. Please perform whatever steps are applicable from the product’s Instruction Manual before

calling or writing as this could save unnecessary phone charges. Please do not return the product without calling Drake Service and

following the steps above rst; it is preferred to help troubleshoot the problem over the phone (or by Email) rst, saving you both time

and money.

Limited Warranty

Seller will at its sole option, either repair or replace (with a new or factory reconditioned product, as Seller may determine) any product manufactured or sold (or in the case of software,

licensed) by Seller which is defective in materials or workmanship or fails to meet the applicable specifications that are in effect on the date of shipment or such other specifications as may

have been expressly agreed upon in writing: (i) for a period of three (3) years from the date of original purchase for all stock hardware products (other than those specifically referenced herein

below having a shorter warranty period); (ii) for a period of one (1) year from the date of original purchase, with respect to all MegaPort™, IPTV products, test equipment and fiber optics

receivers, transmitters, couplers and integrated receiver/distribution amplifiers; (iii) for a period of one (1) year from the date of original purchase (or such shorter period of time as may be set

forth in the license agreement specific to the particular software being licensed from Seller) with respect to all software products licensed from Seller (other than Core Product Software) that

is (a) developed for a specific function or application, (b) complimentary to and does not function without the Core Product Software, and (c) listed with a specific model number and stock

number in Seller’s Price List (“Non-Core Software”); (iv) for a period of ninety (90) days from the date of original purchase, with respect to non-serialized products and accessories, such as

parts, sub-assemblies, splitters and all other products sold by Seller (other than Core Product Software and Refurbished/Closeout Products) not otherwise referred to in clauses (i) through (iii)

above. The warranty period for computer programs in machine-readable form included in a hardware product, which are essential for the functionality thereof as specifically stated in the pub-

lished product specifications (“Core Product Software”) will be coincident with the warranty period of the applicable hardware product within which such Core Product Software is installed.

Software patches, bug fixes, updates or workarounds do not extend the original warranty period of any Core Product Software or Non-Core Software.

Notwithstanding anything herein to the contrary,

(i) Seller’s sole obligation for software that when properly installed and used does not substantially conform to the published specifications in effect when the software is first shipped by Seller,

is to use commercially reasonable efforts to correct any reproducible material non-conformity (as determined by Seller in its sole discretion) by providing the customer with: (a) telephone or

e-mail access to report non-conformance so that Seller can verify reproducibility, (b) a software patch or bug fix, if available or a workaround to bypass the issue if available, and (c) where

applicable, replacement or damaged or defective external media, such as CD-ROM disk, on which the software was originally delivered;

(ii) Seller does not warrant that the use of any software will be uninterrupted, error-free, free of security vulnerabilities or that the software will meet the customer’s particular requirements; and

the customer’s sole and exclusive remedy for breach of this warranty is, at Seller’s option, to receive (a) suitably modified software, or part thereof, or (b) comparable replacement software

or part thereof;

(iii) Seller retains all right, title and interest in and to and ownership of all software (including all Core Product Software and Non-Core Software) including any and all enhancements, modi-

fications and updates to the same; and

(iv) in some cases, the warranty on certain proprietary sub-assembly modules manufactured by third-party vendors and contained in Seller’s products, third party software installed in certain of

Seller’s products, and on certain private-label products manufactured by third-parties for resale by Seller, will be of shorter duration or otherwise more limited than the standard Seller limited

warranty. In such cases, Seller’s warranty with respect to such third-party proprietary sub-assembly modules, third-party software and private-label products will be limited to the duration and

other terms of such third-party vendor’s warranty, if any. The limited warranty set forth above does not apply to any product sold by Seller, which at the time of sale constituted a Refurbished/

Closeout Product, the limited warranty for which is provided in the following paragraph.

Seller will at its sole option, either repair or replace (with a new or factory-reconditioned product, as Seller may determine) any product sold by Seller which at the time of sale constituted a

refurbished or closeout item (“Refurbished/Closeout Product”), which is defective in materials or workmanship or fails to meet the applicable specifications that are in effect on the date of

shipment of that product or fails to meet such other specifications as may have been expressly agreed upon in writing between the parties, for a period of ninety (90) days from the date of original

purchase. Notwithstanding the foregoing, in some cases the warranty on certain proprietary sub-assembly modules manufactured by third-party vendors and contained in Seller products, third

party software installed in certain of Seller’s products, and on certain private-label products manufactured by third-parties for resale by Seller will be of shorter duration or otherwise more lim-

ited than Seller limited warranty for Refurbished/Closeout Products. In such cases, Seller’s warranty for Refurbished/Closeout Products constituting such third party proprietary sub-assembly

modules, third party software, and private-label products will be limited to the duration and other terms of such third-party vendor’s warranty, if any. In addition, notwithstanding the foregoing,

(i) certain Refurbished/Closeout Products that are not manufactured (but are resold) by Seller, may carry the original OEM warranty for such products, if any, which may be longer or shorter

than Seller’s limited warranty for Refurbished/Closeout Products. All sales of Refurbished/Closeout Products are final.

To obtain service under this warranty, the defective product, together with a copy of the sales receipt, serial number if applicable, or any other satisfactory proof of purchase and a brief descrip-

tion of the defect, must be shipped freight prepaid to Seller at the following address: One Jake Brown Road, Old Bridge, New Jersey 08857.

This warranty does not cover failure of performance or damage resulting from (i) use or installation other than in strict accordance with manufacturer’s written instructions, (ii) disassembly

or repair by someone other than the manufacturer or a manufacturer-authorized repair center, (iii) misuse, misapplication or abuse, (iv) alteration, (v) exposure to unusual physical or electrical

stress, abuse or accident or forces or exposure beyond normal use within specified operational or environmental parameters set forth in applicable product specifications, (vi) lack of reasonable

care or (vii) wind, ice, snow, rain, lightning, or any other weather conditions or acts of God.

OTHER THAN THE WARRANTIES SET FORTH ABOVE, SELLER MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND, EXPRESS OR

IMPLIED, AS TO THE CONDITION, DESCRIPTION, FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR AS TO ANY OTHER MATTER, AND SUCH

WARRANTIES SET FORTH ABOVE SUPERSEDE ANY ORAL OR WRITTEN WARRANTIES OR REPRESENTATIONS MADE OR IMPLIED BY SELLER OR BY ANY

OF SELLER’S EMPLOYEES OR REPRESENTATIVES, OR IN ANY OF SELLER’S BROCHURES MANUALS, CATALOGS, LITERATURE OR OTHER MATERIALS. IN

ALL CASES, BUYER’S SOLE AND EXCLUSIVE REMEDY AND SELLER’S SOLE OBLIGATION FOR ANY BREACH OF THE WARRANTIES CONTAINED HEREIN

SHALL BE LIMITED TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT F.O.B SHIPPING POINT, AS SELLER IN ITS SOLE DISCRETION

SHALL DETERMINE. SELLER SHALL IN NO EVENT AND UNDER NO CIRCUMSTANCES BE LIABLE OR RESPONSIBLE FOR ANY CONSEQUENTIAL, INDIRECT,

INCIDENTAL PUNITIVE, DIRECT OR SPECIAL DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT TORT

LIABILITY OR OTHERWISE OR ANY OTHER LEGAL THEORY, ARISING DIRECTLY OR INDIRECTLY FROM THE SALE, USE, INSTALLATION OR FAILURE OF

ANY PRODUCT ACQUIRED BY BUYER FROM SELLER.

All claims for shortages, defects, and non-conforming goods must be made by the customer in writing within five (5) days of receipt of merchandise, which writing shall state with particularity

all material facts concerning the claim then known to the customer. Upon any such claim, the customer shall hold the goods complained of intact and duly protected, for a period of up to sixty

(60) days. Upon the request of Seller, the customer shall ship such allegedly non-conforming or defective goods, freight prepaid to Seller for examination by Seller’s inspection department

and verification of the defect. Seller, at its option, will either repair, replace or issue a credit for products determined to be defective. Seller’s liability and responsibility for defective products is

specifically limited to the defective item or to credit towards the original billing. All such replacements by Seller shall be made free of charge f.o.b. the delivery point called for in the original

order. Products for which replacement has been made under the provisions of this clause shall become the property of Seller. Under no circumstances are products to be returned to Seller without

Seller’s prior written authorization. Seller reserves the right to scrap any unauthorized returns on a no-credit basis. Any actions for breach of a contract of sale between Seller and a customer

must be commenced by the customer within thirteen (13) months after the cause of action as accrued. A copy of Seller’s standard terms and conditions of sale, including the limited warranty,

is available from Seller upon request. Copies of the limited warranties covering third-party proprietary sub-assembly modules and private-label products manufactured by third-parties may

also be available from Seller on request. (Rev 0713)

R.L. DRAKE HOLDINGS

Sales: 937-746-4556 • Support: 937-746-6990 • Fax: 937-806-1510

www.rldrake.com