Sony VLCP40ATA Manuel utilisateur

LCD Data Projector VPL-PX40/PX35

4-090-532-13 (1)

Data Projector

GB

FR

ES

Operating Instructions

Mode d’emploi

Manual de instrucciones

VPL-PX40/PX35

GB

2

WARNING

To prevent fire or shock hazard, do

not expose the unit to rain or

moisture.

To avoid electrical shock, do not

open the cabinet. Refer servicing to

qualified personnel only.

This symbol is intended to

alert the user to the presence

of uninsulated “dangerous

voltage” within the

product’s enclosure that may

be of sufficient magnitude to

constitute a risk of electric

shock to persons.

This symbol is intended to

alert the user to the presence

of important operating and

maintenance (servicing)

instructions in the literature

accompanying the

appliance.

3

GB

For the customers in the USA

This equipment has been tested and found to

comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated

in a commercial environment. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instruction

manual, may cause harmful interference to

radio communications. Operation of this

equipment in a residential area is likely to

cause harmful interference in which case the

user will be required to correct the

interference at his own expense.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

Caution

Use of controls or adjustments or

performance of procedures other than those

specified herein may result in hazardous

radiation exposure.

Notes

• Do not aim the laser at people or not look

into the laser transmitter.

• When the Remote Commander causes

malfunction, consult with qualified Sony

personnel. We change the Remote

Commander as new one according to the

guarantee.

For the customers in Canada

This Class A digital apparatus complies with

Canadian ICES-003.

For the customers in the United

Kingdom

WARNING

THIS APPARATUS MUST BE

EARTHED

This label is located on

the rear of the Remote

Commander.

This label is located on

the side of the Remote

Commander.

This label is located on

the rear of the Remote

Commander.

This label is located on

the rear of the Remote

Commander.

LASER RADIATION

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

RAYONNEMENT LASER

NE PAS REGARDER DANS LE FAISCEA

U

APPAREIL A LASER DE CLASSE 2

LASER–STRAHLING,

NICHT IN DEN STRAHL BLICKEN

LASER KLASSE 2

MAX OUTPUT : 1mW EN60825

-

WAVE LENGTH : 645nm /A11:19

9

LASER RADIATION

DO NOT STARE INTO BEAM

WAVE LENGTH:645nm

MAX OUTPUT:1mW

CLASS II LASER PRODUCT

COMPLIES WITH DHHS 21 CFR

SUBCHAPTER J

SONY CORPORATION

6-7-35 KITASHINAGAWA

SHINAGAWA-KU,TOKYO,JAPAN

A

MANUFACTURED;

CAUTION

AVOID EXPOSURE-

LASER RADIATION IS

EMITTED FROM THIS

APERTURE.

Laser light shines out of this window.

GB

4

IMPORTANT

The wires in this mains lead are coloured in

accordance with the following code:

Green-and-Yellow:Earth

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead

of this apparatus may not correspond with

the coloured markings identifying the

terminals in your plug proceed as follows:

The wire which is coloured green-and-

yellow must be connected to the terminal in

the plug which is marked by the letter E or

by the safety earth symbol I or coloured

green or green-and-yellow.

The wire which is coloured blue must be

connected to the terminal which is marked

with the letter N or coloured black. The wire

which is coloured brown must be connected

to the terminal which is marked with the

letter L or coloured red.

Voor de klanten in Nederland

Gooi de batterij niet weg

maar lever deze in als klein

chemisch afval (KCA).

The socket-outlet should be installed near

the equipment and be easily accessible.

5

GB

Table of Contents

GB

Overview

Precautions .........................................6

Notes on Installation ..........................7

Unsuitable Installation ..................7

Usage in High Altitude .................7

Unsuitable Conditions ..................8

Features ..............................................8

Location and Function of Controls .10

Front/Left Side ...........................10

Rear/Right Side/Bottom .............10

Control Panel ..............................12

Connector Panel .........................13

Remote Commander ...................14

Setting Up and Projecting

Installing the Projector .....................17

Connecting the Projector ..................18

Connecting with a Computer ......18

Connecting with a VCR or 15k

RGB/Component

Equipment .......................20

Selecting the Menu Language ..........22

Projecting .........................................24

Effective Tools for Your

Presentation .....................28

Adjustments and Settings

Using the Menu

Using the MENU ............................. 30

The PICTURE SETTING Menu ..... 31

The INPUT SETTING Menu .......... 33

The SET SETTING Menu ............... 35

The MENU SETTING Menu .......... 36

The INSTALL SETTING Menu ..... 36

The INFORMATION Menu ............ 37

Maintenance

Maintenance .................................... 38

Replacing the Lamp ................... 38

Cleaning the Air Filter ............... 39

Troubleshooting ............................... 41

Warning Messages ..................... 43

Caution Messages ...................... 44

Other

Specifications .................................. 45

Index ............................................... 53

GB

6

Precautions

B Overview

Precautions

On safety

• Check that the operating voltage of your

unit is identical with the voltage of your

local power supply.

• Should any liquid or solid object fall into

the cabinet, unplug the unit and have it

checked by qualified personnel before

operating it further.

• Unplug the unit from the wall outlet if it is

not to be used for several days.

• To disconnect the cord, pull it out by the

plug. Never pull the cord itself.

• The wall outlet should be near the unit and

easily accessible.

• The unit is not disconnected to the AC

power source (mains) as long as it is

connected to the wall outlet, even if the

unit itself has been turned off.

• Do not look into the lens while the lamp is

on.

• Do not place your hand or objects near the

ventilation holes. The air coming out is

hot.

• Be careful not to catch your fingers by the

adjuster when you adjust the height of the

projector. Do not push hard on the top of

the projector with the adjuster out.

On illumination

• To obtain the best picture, the front of the

screen should not be exposed to direct

lighting or sunlight.

• Ceiling-mounted spot lighting is

recommended. Use a cover over

fluorescent lamps to avoid lowering the

contrast ratio.

• Cover any windows that face the screen

with opaque draperies.

• It is desirable to install the projector in a

room where floor and walls are not of

light-reflecting material. If the floor and

walls are of reflecting material, it is

recommended that the carpet and wall

paper be changed to a dark color.

On preventing internal heat build-

up

After you turn off the power with the I / 1

key, do not disconnect the unit from the wall

outlet while the cooling fan is still running.

Caution

The projector is equipped with ventilation

holes (intake) and ventilation holes

(exhaust). Do not block or place anything

near these holes, or internal heat build-up

may occur, causing picture degradation or

damage to the projector.

On cleaning

• To keep the cabinet looking new,

periodically clean it with a soft cloth.

Stubborn stains may be removed with a

cloth lightly dampened with a mild

detergent solution. Never use strong

solvents, such as thinner, benzene, or

abrasive cleansers, since these will

damage the cabinet.

• Avoid touching the lens. To remove dust

on the lens, use a soft dry cloth. Do not use

a damp cloth, detergent solution, or

thinner.

• Clean the filter at regular intervals.

On repacking

• Save the original shipping carton and

packing material; they will come in handy

if you ever have to ship your unit. For

maximum protection, repack your unit as

it was originally packed at the factory.

On LCD projector

• The LCD projector is manufactured using

high-precision technology. You may,

however, see tiny black points and/or

bright points (red, blue, or green) that

continuously appear on the LCD projector.

This is a normal result of the

manufacturing process and does not

indicate a malfunction.

7

GB

Notes on Installation

Overview

Notes on Installation

Do not install the projector in the following

situations. These installations may cause

malfunction or damage to the projector.

Poorly ventilated

• Allow adequate air circulation to prevent

internal heat build-up. Do not place the

unit on surfaces (rugs, blankets, etc.) or

near materials (curtains, draperies) that

may block the ventilation holes.

• When the internal heat builds up due to the

block-up, the temperature sensor will

function with the message “High temp.!

Lamp off in 1 min.” The power will be

turned off automatically after one minute.

• Leave space of more than 30 cm (11

7

/8

inches) around the unit.

• Be careful that the ventilation holes may

inhale tininess such as a piece of paper.

Highly heated and humid

• Avoid installing the unit in a location

where the temperature or humidity is very

high, or temperature is very low.

• To avoid moisture condensation, do not

install the unit in a location where the

temperature may rise rapidly.

Very dusty

Avoid installing the unit in a location where

there is a lot of dust; otherwise, the air filter

will be obstructed. The dust blocking the air

through the filter may cause raising the

internal heat of the projector. Clean it up

periodically.

When using the projector at an altitude of

1,500 m or higher, turn on “High

Altitude Mode” in the INSTALL SETTING

menu. Failing to set this mode when using

the projector at high altitudes could have

adverse effects, such as reducing

the reliability of certain components.

Unsuitable Installation

Usage in High Altitude

GB

8

Features

Do not use the projector under the following

conditions.

Toppling the unit.

Avoid using as the unit topples over on its

side. It may cause malfunction.

Tilting right/left

Avoid using as the unit tilts more than 20

degrees. Do not install the unit other than on

the floor or ceiling. These installations may

cause malfunction.

Blocking the ventilation holes

Avoid using something to cover over the

ventilation holes (exhaust/intake);

otherwise, the internal heat may build up.

When using a screen with an uneven surface,

stripes pattern may rarely appear on the screen

depending on the distance between the screen

and the projector or the zooming

magnifications. This is not a malfunction of the

projector.

Features

High brightness, high picture

quality

• High brightness

This projector is equipped with a high-

efficiency optical system made possible

by adopting Sony’s new proprietary

optical system. Because the VPL-PX40

utilizes a newly developed high N.A. LCD

panel with a microlens and a 265W UHP

lamp, it can reproduce bright images at

3500 ANSI lumens, while the VPL-PX35

with no microlens can reproduce bright

images at 2600 ANSI lumens.

•High resolution

Three 0.99-inch, about 790,000 pixel,

XGA panels provide a resolution of 1024

× 768 dots for RGB input and 750

horizontal TV lines for video input.

Easy Setup

• Permits setup on a front-to-back slope

This projector can be set up on a slope of

up to 90 degrees up or down. The

projector also permits rear projection

using a mirror.

• Optional lenses

The projector can be adapted to a variety

of different types of installations by using

one of three lenses (sold separately), two

with a short focus and one with a long

focus.

• Direct Power On/Power Off function

The AC power for the entire system can be

turned on and off by means of a breaker or

other switch.

• System expandability (network

compatibility)

In addition to conventional serial control

using an RS-232C connector, this

projector also supports connection to an

network environment through an Ethernet

connector. This function can be used to

control multiple projectors and also makes

it possible to acquire status information

from each projector, such as the length of

time the lamp has been on.

Unsuitable Conditions

Note

20°

9

GB

Features

Overview

(For details on the network functions,

contact your dealer or the Sony customer

service.)

Convenient presentation functions

• Equipped with USB connector

Simply by connecting the projector to a

computer through the USB interface, the

Remote Commander provided with the

projector can then be used as a wireless

mouse.

• Remote Commander with laser pointer

The Remote Commander comes equipped

with a laser pointer that is useful when

making presentations.

Accepts various input signals

• Equipped with DVI connector and

5BNC connector

The projector is equipped with a DVI-D

connector that can be used to connect a

digital RGB device.

The projector is also equipped with a

5BNC input connector that supports high-

precision signal connection with a

workstation or other device, as well as

long-distance transmission.

• Scan converter loaded

This projector has a build-in scan

converter that converts the input signal

within 1,024 × 768 dots.

• Compatible input signals

This projector accepts video signals of

composite, S video, and component as

well as 15k RGB, VGA, SVGA, XGA,

SXGA, SXGA+ and UXGA (60 Hz)

signals, which all can be displayed. In this

projector, 46 types of input signals are

preset.

• Compatible with six color systems

NTSC, PAL, SECAM, NTSC

4.43

1)

, PAL-

M, or PAL-N color system can be selected

automatically or manually.

1)NTSC4.43 is the color system used when

playing back a video recorded on NTSC

on a NTSC

4.43 system VCR.

...............................................................................

• Windows is a registered trademark of

Microsoft Corporation in the United States

and/or other countries.

• IBM PC/AT, VGA, SVGA, XGA, SXGA

and UXGA are registered trademarks of

the International Business Machines

Corporation, U.S.A.

• Kensington is a registered trademark of

Kensington Technology Group.

• Macintosh is a registered trademark of

Apple Computer, Inc.

• VESA is a registered trademark of Video

Electronics Standard Association.

• Display Data Channel is a trademark of

Video Electronics Standard Association.

GB

10

Location and Function of Controls

Location and

Function of Controls

a Handle

b Zoom ring

Adjusts the picture size.

c Control panel

For details, see “Control Panel” on

page 12.

d Connector panel

For details, see “Connector Panel” on

page 13.

e AC IN socket

Connects the supplied AC power cord.

f Front remote control detector

g Lens

Remove the lens cap before projection.

h Ventilation holes (exhaust)

i Focus ring

Adjusts the picture focus.

j Rear remote control detector

k Indicators

• LAMP/COVER: Lights up or flashes

under the following conditions:

– Lights up when the lamp has

reached the end of its life or

becomes a high temperature.

– Flashes when the lamp cover or air

filter cover is not secured firmly.

• TEMP (Temperature)/FAN: Lights

up or flashes under the following

conditions:

– Lights up when temperature inside

the projector becomes unusually

high.

– Flashes when the fan is broken.

For details on the LAMP/COVER and

the TEMP/FAN indicators, see on

page 43.

• POWER SAVING: Lights up when

the projector is in power saving mode.

When POWER SAVING in the SET

SETTING menu is set to ON, the

projector goes into power saving mode

if no signal is input for 10 minutes.

Front/Left Side

Rear/Right Side/Bottom

11

GB

Location and Function of Controls

Overview

Although the lamp goes out, the

cooling fan keeps running. The power

saving mode is canceled when a signal

is input or any key is pressed. In power

saving mode, any key does not

function for the first 60 seconds after

the lamp goes out.

• ON/STANDBY: Lights up or flashes

under the following conditions:

– Lights in red when a AC power cord

is plugged into a wall outlet. Once in

standby mode, you can turn on the

projector with the I / 1 key.

– Lights in green when the power is

turned on.

– Flashes in green while the cooling

fan runs after the power is turned off

with the I / 1 key. The fan runs for

about 90 seconds after the power is

turned off.

The ON/STANDBY indicator

flashes quickly for the first 60

seconds. During this time, you

cannot light up the ON/STANDBY

indicator with the I / 1 key.

l Lamp cover

m Security lock

Connects to an optional security cable

(Kensington’s).

Home page address:

http://www.kensington.com/

n Adjuster adjustment buttons

For details, see “How to use the

adjuster” on page 11.

o Adjuster

p Speaker

q Ventilation holes (intake)/air

filter cover

• Do not place anything near the

ventilation holes as it may cause

internal heat build-up.

• Do not place your hand or objects near

the ventilation holes as it may cause the

air coming out heat build-up.

• To maintain optimal performance, clean

the air filter every 1500 hours.

For details, see “Cleaning the Air

Filter” on page 39.

How to use the adjuster

To adjust the height

Adjusts the height of the projector as

follows:

1 Lift the projector and press the

adjuster adjustment buttons.

The adjusters will extend from the

projector.

2 While pressing the buttons, adjust the

projector to the desired height, and

then release the buttons. For fine

adjustment, turn the adjusters to the

right and the left.

• Be careful not to let the projector down on

your fingers.

• Do not push hard on the top of the projector

with the adjusters out.

It may be occurred malfunction.

Note

Notes

Adjuster adjustment buttons

to lower

the

projector

to raise the

projector

GB

12

Location and Function of Controls

a I / 1 (on/standby) key

Turns on and off the projector when the

projector is in standby mode. The ON/

STANDBY indicator lights in green

when the power is turned on.

When turning off the power, press

the I / 1 key twice following the

message on the screen, or press and

hold the key for about one second.

For details on steps for turning off the

power, see “To turn off the power” on

page 28.

b MENU key

Displays the on-screen menu. Press

again to clear the menu.

c Arrow keys (M/m/</,)

Used to select the menu or to make

various adjustments.

d APA (Auto Pixel Alignment) key

Pressing this key while a signal from a

computer is being input automatically

adjusts the picture so that it can be seen

clearly. This function also

simultaneously adjusts the screen size

and makes up/down and left/right shift

adjustments.

Press the APA key when the full image is

displayed on the screen. If the projected

image includes a large black area around

the periphery, the APA function will not

function properly and in some cases,

portions of the image may not be

displayed.

• You can cancel the adjustment by

pressing the APA key again while

“Adjusting” appears on the screen.

• The picture may not be adjusted properly

depending on the kinds of input signals.

• Adjust the items “Dot Phase,” “H Size”

and “Shift” in the INPUT SETTING

menu when you adjust the picture

manually.

e RESET key

Resets the value of an item back to its

factory preset value. This key functions

when the menu or a setting item is

displayed on the screen.

f VOLUME +/– key

Adjusts the volume of the built-in

speakers and output level of the AUDIO

jack.

+:Increases the volume.

–:Decreases the volume.

g ENTER key

Enters the settings of items in the menu

system.

h INPUT key

Selects the input signal. Each time you

press the key, the input signal switches

as follows:

The audio signals are common to the

INPUT B, INPUT C, VIDEO and

S-VIDEO.

Control Panel

INPUT

VOLUME

INPU

INP

U

ET

H

APAMENU

RESETENTER

CONT

I/

Note

t INPUT A t INPUT B t INPUT C t

S VIDEO T VIDEO T INPUT D

13

GB

Location and Function of Controls

Overview

a INPUT A connectors

Connect to a computer.

• HD D-sub 15-pin, female:

Connect to the monitor output on a

computer using the supplied cable.

• AUDIO (stereo mini-jack): Connects

to the audio output on a computer.

b ETHER (RJ-45)

Connects to the LAN cable when the

network function is in use.

Consult the dealer for connection and

installation.

c RS-232C connector (D-sub 9-

pin, female)

Connects to a computer to operate the

projector from the computer.

d CONTROL S IN/PLUG IN

POWER (DC 5V output) jack

Connects to the control S out jacks of the

Sony equipment. Connects to the

CONTROL S OUT jack on the supplied

Remote Commander when using it as a

wired Remote Commander. In this case,

when a stereo cable is used, you do not

need to install the batteries in the

Remote Commander, since the power is

supplied from this jack.

e USB connector (USB plug for

upstream, 4-pin)

Connects to the USB connector on a

computer. When you connect the

projector to the computer, you can

control the mouse function with the

supplied Remote Commander.

f Video input connectors

Connect to external video equipment

such as a VCR.

• S VIDEO (mini DIN 4-pin):

Connects to the S video output (Y/C

video output) of video equipment.

• VIDEO (phono type): Connects to

the composite video output of video

equipment.

• AUDIO input L (MONO)/R (phono

type): Connect to the audio output of

equipment. For stereo equipment, use

both the L and R jacks; for monaural

equipment, use the L (MONO) jack

only.

g INPUT B connectors

Connect to a computer.

• HD D-sub 15-pin, female:

Connects to the monitor output on a

computer using the supplied cable.

• AUDIO (stereo mini-jack)/Shared

by INPUT B and C: Connects to the

audio output on a computer.

h INPUT C connector (RGB (DVI))

(DVI-D)

Connects to a computer equipped with

DVI (digital) output connector with a

DVI cable.

i OUTPUT connectors

MONITOR (HD D-sub 15-pin,

female):

Connect to the video input connector on

the monitor. Outputs signals from the

selected channel and computer signals

only from among the signals from the

INPUT A, INPUT B, or INPUT D RGB

connector. This connector does not

output any signals from the INPUT C

connector.

• AUDIO (stereo mini-jack): Connects

to external active speakers. The

volume of the speakers can be

controlled by the VOLUME +/– keys

on the Remote Commander or the

VOLUME +/– keys on the control

panel.

Connector Panel

VOLUME

~AC IN

INPUT D OUTPUT

INPUT A INPUT B INPUT C

ETHER

(PLUS IN POWER)

(MONO)

LR

RS-232C IN S VIDEO VIDEO AUDIO

RGB AUDIO RGB DVI-D

R/R-Y/Pn G/Y B/B-Y/Ps SYNC/HD VD AUDIO MONITOR AUDIO

AUDIO

ENTERMENU

RESETAPA

CONTROL

REMOTE VIDEO IN

CONTROL S

GB

14

Location and Function of Controls

j INPUT D, 5BNC input

connectors (R/R-Y/P

R, G/Y, B/B-

Y/P

B, SYNC/HD, VD connectors)

(BNC type):

Connect to a high-resolution computer

or VCR where signals are transmitted

long distances; for example, when the

projector has been hung from the

ceiling.

According to the connected equipment,

computer, component (R-Y/Y/B-Y),

HDTV or DTV (DTV GBR, DTV

YP

BPR) signal is selected.

• AUDIO (stereo mini-jack): Connects

to the audio output on a computer.

k AC IN socket

Connects the supplied AC power cord.

The keys which have the same names as on

the control panel function identically.

a I / 1 key

b MUTING keys

Cut off the picture and sound.

• PIC: Cuts off the picture. Press again

to restore the picture.

• AUDIO: Press to temporarily cut off

the audio output from the speaker, and

the output on the AUDIO jack in the

OUTPUT section.

Press again or press the VOLUME +

key to restore the sound.

c INPUT key

Remote Commander

MUTING

PIC

AUDIO

LENS

APA

LASER

INPUT

D KEYSTONE

HELP

PJ NETWORK

ON

COMMAND

OFF

VOLUME

ENTER

FUNCTION

RM-PJM15

PROJECTOR

D ZOOM

CLICK

RESET/

ESCAPE

MENU/

TAB

R

1

2

3

1

2

3

4

8

9

q;

qa

qs

wg

wf

wd

ws

wa

w;

ql

qk

qj

qh

qg

qd,qf

wh

FREEZE

6

7

5

15

GB

Location and Function of Controls

Overview

d D KEYSTONE key

Corrects the trapezoidal distortion

caused by the projection angle. Use the

arrow keys (M/m/</,) to display the

image as a rectangle.

e HELP key

This function is not provided in this

projector.

f FREEZE key

This key freezes the projected image.

Press again to unfreeze the image.

g LASER key

Emits laser beam from the laser

transmitter when you press this key.

h Joy stick

Functions as a mouse of a computer

connected to the unit.

i Arrow keys (M/m/</,)

j R CLICK key

Functions as a right button on a mouse of

a computer connected to the unit.

k ENTER key

l FUNCTION 1/2/3 keys

This key does not work in the unit.

m Strap holder

Attaches the supplied strap.

n CONTROL S OUT jack (stereo

mini-jack)

Connects to the CONTROL S IN jack on

the projector with the connecting cable

(not supplied) when using the Remote

Commander as a wired one. In this case,

you do not need to install the batteries

since the power is supplied via the

CONTROL S IN jack on the projector.

o RESET/ESCAPE key

Functions as a RESET key.

p D ZOOM +/– key

Enlarges the image at a desired location

on the screen.

+: Pressing the + key once displays the

icon. This icon indicates the point you

want to enlarge. Use an arrow key (M/

m/</,) to move the icon to the

point to be enlarged. Press the + key

repeatedly until the image is enlarged

to your requirements.

–: Pressing the – key reduces an image

that has been enlarged with the D

ZOOM + key.

q L CLICK key

Functions as a left button on a mouse of

a computer connected to the unit.

r MENU/TAB key

Functions as a MENU key.

s APA (Auto Pixel Alignment) key

t VOLUME +/– keys

u LENS key

This function is not provided in this

projector.

v PJ/NETWORK (Projector/

Network) selector switch

Set this switch to PJ always.

w COMMAND ON/OFF switch

When this switch is set to OFF, no key

on the Remote Commander function.

This saves the battery power.

x Transmission indicator

Lights up when you press a key on the

Remote Commander.

This indicator does not light up when

you use the laser pointer.

y Infrared transmitter

z Laser transmitter

GB

16

Location and Function of Controls

Battery installation

1 Push and slide to open the lid, then

install the two size AA (R6) batteries

(supplied) with the correct polarity.

2 Replace the lid.

Notes on batteries

• Make sure that the battery orientation is

correct when inserting batteries.

• Do not mix an old battery with a new one

or different types of batteries.

• If you will not use the Remote

Commander for a long time, remove the

batteries to avoid damage from battery

leakage. If batteries have leaked, remove

them, wipe and dry the battery

compartment, and replace the batteries

with new ones.

Notes on laser beam

• Do not look into the laser transmitter.

• Do not aim the laser at people.

Notes on Remote Commander

operation

• Make sure that nothing to obstruct the

infrared beam between the Remote

Commander and the remote control

detector on the projector.

• The operation range is limited. The shorter

the distance between the Remote

Commander and the projector is, the wider

the angle within which the commander can

control the projector.

Be sure to install the battery

from the # side.

While pressing the lid, slide it.

17

GB

Installing the Projector

Setting Up and Projecting

B Setting Up and Projecting

Installing the Projector

This section describes how to install the projector.

For details on ceiling installation, consult with qualified Sony personnel.

Unit: m (ft)

Screen size

(inches)

40 60 80 100 120 150 200 300

Minimum

Distance

1.5

(4.9)

2.3

(7.5)

3.0

(10.0)

3.8

(12.5)

4.6

(15.0)

5.8

(19.0)

7.7

(25.2)

11.6

(37.9)

Maximum

Distance

1.9

(6.2)

2.9

(9.5)

3.8

(12.5)

4.8

(15.7)

5.8

(19.0)

7.2

(23.6)

9.7

(31.7)

14.5

(47.6)

Note

Distance between the screen and

the center of the lens

The distance between the lens and the screen varies depending on the size of the

screen. Use the following table as a guide.

GB

18

Connecting the Projector

When you connect the projector, make sure to:

• Turn off all equipment before making any connections.

• Use the proper cables for each connection.

• Insert the cable plugs firmly; loose connections may increase noise and

reduce performance of picture signals. When pulling out a cable, be sure to

pull it out from the plug, not the cable itself.

To connect the projector, refer to the illustrations on the next and the

following pages.

This section describes how to connect the projector to a computer.

For more information, refer to the computer’s instruction manual.

• The projector accepts 15k RGB, VGA, SVGA, XGA, SXGA, SXGA+ and UXGA

(60 Hz) signals. However, we recommend that you set the output mode of your

computer to XGA mode for the external monitor.

• If you set your computer, such as a notebook type, to output the signal to both your

computer’s display and the external monitor, the picture of the projector may not

appear properly. Set your computer to output the signal to only the external monitor.

For details, refer to the computer’s operating instructions supplied with your

computer.

• This projector is compatible with a DDC2B (Digital Data Channel 2B). If your

computer is compatible with a DDC, turn the projector on according to the following

procedures.

1 Connect the projector to the computer by using the supplied HD D-sub 15-pin cable

or DVI cable.

2 Turn the projector on.

3 Start the computer.

Connecting with a Computer

Notes

19

GB

Connecting the Projector

Setting Up and Projecting

To connect an IBM PC/AT compatible computer

When you use a wireless mouse

On the USB function

When connecting the projector to a computer by using the USB cable for the

first time, the computer recognizes the following devices automatically.

USB human interface device (wireless mouse function)

Recommended operating environment

When you use the USB function, connect your computer as illustrated above.

The USB mouse function can be used on a computer that came with Windows

98, Windows 98 SE, Windows ME, Windows 2000 or Windows XP

preinstalled models.

• Your computer may not start correctly when connected to the projector via the USB

cable. In this case, disconnect the USB cable, restart the computer, then connect the

computer to the projector using the USB cable.

• This projector is not guaranteed for suspend, standby mode. When you use the

projector in suspend, standby mode, disconnect the projector from the USB port on

the computer.

• Operations are not guaranteed for all the recommended computer environments.

Notes

INPUT D OUTPUT

INPUT A INPUT B INPUT C

ETHER

(PLUS IN POWER)

(MONO)

LR

RS-232C IN S VIDEO VIDEO AUDIO

RGB AUDIO RGB DVI-D

R/R-Y/Pn G/Y B/B-Y/Ps SYNC/HD VD AUDIO MONITOR AUDIO

AUDIO

CONTROL

REMOTE VIDEO IN

CONTROL S

to USB connector

Right side

USB cable (supplied)

(Connect the USB cable to use a

wireless mouse.)

to monitor output

Computer

HD D-sub 15-pin cable (supplied)

to audio output

a) Use a no-resistance cable.

b) Connect a DVI cable to use a DVI equipment.

DVI cable (not

supplied)

b)

To DVI-D

output

Stereo audio connecting cable (not supplied)

a)

GB

20

Connecting the Projector

To connect a Macintosh computer

To connect a Macintosh computer equipped with video output connector of a

type having two rows of pins, use a commercially available plug adaptor.

When you connect a USB capable Macintosh computer using the USB cable

to the projector, wireless mouse functions become available.

This section describes how to connect the projector to a VCR and 15k RGB/

component equipment.

For more information, refer to the instruction manuals of the equipment you

are connecting.

To connect a VCR

Connecting with a VCR or 15k RGB/Component Equipment

INPUT B INPUT C

W

ER)

(MONO)

LR

S VIDEO VIDEO AUDIO

RGB DVI

-

D

AUDIO

VIDEO IN

S

Audio connecting cable (not supplied)

VCR

to S video

output

Right side

to audio

output

Video cable (not supplied) or

S-Video cable (not supplied)

to video output

For stereo equipment, use both the L and R jacks.

For monaural equipment, use the L (MONO) jack only.

La page charge ...

Sony VLCP40ATA Manuel utilisateur

Sony VLCP40ATA Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents