Palm Desktop Organizer Read This First Manual

Marque: Palm

Modèle: Desktop Organizer

Taper: Read This First Manual

Palm

™

Desktop

Organizer Software

Read This First

Getting Started

Table of Contents

English

...................................................3

Deutsch ...............................................13

Français...............................................24

Español................................................35

Italiano ................................................46

P/N: 405-1087 A

Introduction

With Palm™ Desktop organizer software, a Palm Computing

handheld and the proper

adapter cable, you have everything you need to connect your handheld to your

Macintosh computer and transfer information between them.

If you have a PowerPC Macintosh, you will need a Palm Macintosh Serial Adapter to

connect your HotSync

Cradle to a printer or modem port on your Macintosh.

If you have an iMac, iBook or G3 Apple computer equipped with USB, you will need a

USB to serial port adapter and the USB drivers from the adapter manufacturer to connect

your HotSync Cradle to the USB port on your Macintosh.

Note: USB users need one of the following to connect a cradle to an iMac, iBook or G3:

• PalmConnect USB Kit

– or –

• a third-party USB adapter cable or device

(check for compatibility with third-party manufactures

and Palm Desktop software)

This documentation assumes you have a Palm USB to serial port adapter.

Handheld package

Handheld

Cradle

Palm Accessory

Macintosh Serial Adapter cable

PalmConnect

USB Kit

USB Serial Adapter cable

The Palm™ Desktop organizer software helps you organize your addresses,

appointments, tasks, and notes. It also contains HotSync

Manager software that

transfers data between your Macintosh and your handheld.

Note: If you have a previous version of Palm Desktop software installed, perform

a HotSync operation now to ensure the latest data is on your handheld.

If you are upgrading, you still need to do a full installation to install the

updates to the HotSync Manager software.

Turn on your Macintosh.

Install the Palm Desktop software.

• Locate the Palm

™

Desktop Installer icon.

• Double-click the Palm

™

Desktop Installer icon.

• Follow the onscreen instructions.

Reboot your Macintosh when the installation is done.

Install the Palm

™

Desktop organizer software

Synchronize your data.

• Place your handheld in the cradle and press the HotSync button.

This operation updates and exchanges data between your Macintosh and your handheld.

Congratulations!

You have successfully completed this installation and performed your first HotSync operation.

Note: The AC power adapter is only required

for Palm V™ handheld users.

Make the connection.

• Connect the USB to serial port adapter to your cradle connector

(or HotSync

Cable).

• Connect the USB to serial port adapter to the USB port on your Macintosh.

USB Macintosh – make the connection

Turn off your Macintosh.

Make the connection.

• Connect the Macintosh adapter to the cable on your cradle.

• Connect the cradle to either the printer or modem port on the back of the computer.

Note: Remember which port you connected the cradle to;

you’ll need that information later.

Turn on your Macintosh.

Synchronize your data.

• Place your handheld in the cradle and press the HotSync

button.

This operation updates and exchanges data between your Macintosh and your handheld.

Congratulations! You have successfully completed this installation and performed

your first HotSync operation.

Modem port

Printer port

PowerPC Macintosh – make the connection

Double click the Palm

™

Desktop icon in the Palm folder.

To enter data, click one of the following Palm Desktop icons. When you transfer

the data to your handheld during a HotSync

operation, the data appears in the

corresponding handheld applications:

To understand the differences between Palm Desktop organizer software and the

handheld applications, see the help file for the Palm Desktop software.

If you were using Claris Organizer, you can now migrate your data to Palm Desktop

organizer software.

• Make a backup copy of your Claris Organizer data file.

• Launch Palm Desktop software, and choose Merge from the File menu.

• Navigate to your existing Claris Organizer data file, then click Open.

Your Claris Organizer data is now included in your Palm Desktop file.

Perform a HotSync operation to transfer the data to your handheld.

Launch Palm

™

Desktop organizer software

Date Book Address Book To Do List Memo Pad

Appointments Contacts Tasks Notes

Palm Desktop Software

Handheld Applications

Migrating data from Claris Organizer

Installing applications on your handheld

You can easily expand your handheld’s capabilities by downloading any of the

thousands of freeware, shareware, and commercial applications available on the

Internet. Just follow these steps:

Download applications from www.palm.com (or other web site).

Unstuff or unzip the application if it is stuffed or zipped.

If you don’t have it already, you need to download StuffIt Expander or

an application to unzip files, such as ZipIt.

Select the application you want to install.

• Double-click the HotSync

Manager icon in the Palm folder.

• Choose Install from the HotSync menu.

• Drag the application files to the Install Palm Applications dialog box.

Perform a HotSync operation to transfer the applications to your handheld.

Conduits from Palm Computing and other software providers allow you to transfer

information between more applications on your handheld and applications on

your Macintosh.

To install a conduit:

Drag the conduit file(s) into the Conduits folder inside the Palm folder.

Configure the conduit in the HotSync Manager application.

• Double-click the HotSync Manager icon in the Palm folder.

• Choose Conduit Settings from the HotSync menu.

• Configure the conduit appropriately.

Perform a HotSync operation to use the conduit.

Installing conduits

How can I update my Macintosh to the latest MacOS?

Go to the Apple web site http://www.apple.com. This web site contains instructions for

updating to the latest release of the MacOS.

Why can’t I perform a HotSync

operation after I plug in my USB to

serial port adapter?

The serial port settings need to be adjusted. To correct this problem:

1. Check the USB to serial port adapter connections.

2. Launch HotSync Manager.

3. Disable HotSync Manager.

4. Click the Serial Port Settings tab.

5. Under Local Setup, select PalmConnect USB from the Port list

-or-

if you are using a third-party adapter cable, select it from the Port list.

6. Click the HotSync Controls tab and select Enabled.

7. Try performing a HotSync operation.

Why does an error message appear when I remove the USB to serial port

adapter and reboot my Macintosh?

HotSync Manager does not support all USB plug and play features. If you temporarily

disconnect the USB to serial port adapter, the following error message appears:

“HotSync Manager has been disabled because the USB cable is not plugged into your

Macintosh. Please reconnect the cable to the USB port before enabling HotSync Manager.”

To proceed, simply click OK in the message box. To prevent this error message from

appearing during reboot, launch HotSync Manager, choose Setup, disable HotSync

Manager, and then disconnect the USB to serial port cable.

Note: For additional troubleshooting tips, see the help file for

Palm Desktop software.

Troubleshooting

Limited warranty

HARDWARE: Palm Computing, Inc., a subsidiary of 3Com Corporation (collectively “3Com”), warrants to the original end user (“Customer”)

that this product will be free from defects in workmanship and materials, under normal use, for one year from the date of original purchase from

3Com or its authorized reseller. 3Com’s sole obligation under this express warranty shall be, at 3Com’s option and expense, to replace the product

or part with a comparable product or part, repair the product or part, or if neither repair nor replacement is reasonably available, 3Com may, in its

sole discretion, refund to Customer the purchase price paid for the product or part. Replacement products or parts may be new or reconditioned.

3Com warrants any replaced or repaired product or part, and any hardware upgrade to which Customer is entitled under an agreement between

Customer and 3Com, for a period of ninety (90) days from shipment, or through the end of the original warranty, whichever is longer. All products

or parts that are replaced become the property of 3Com.

Accessory products, as listed in the applicable 3Com catalogue, are not covered under this Limited Warranty except for the modem for the

connected organizer, the cradles, cables, memory upgrades, and leather items sold under the 3Com

brand. 3Com shall not be responsible for

Customer’s software, firmware, information, or memory data contained in, stored on, or integrated with any products returned to 3Com for repair,

whether under warranty or not.

SOFTWARE: 3Com warrants to Customer that the Palm™ Desktop organizer software and Palm OS™ software licensed from it will perform in

substantial conformance to their program specifications, for a period of ninety (90) days from the date of original purchase from 3Com or its

authorized reseller. 3Com warrants the media containing software against failure during the warranty period. No updates are provided. 3Com does

not provide any warranty for Adobe

Acrobat

Reader or any other third-party applications software that is licensed to Customer by the third party.

3Com’s sole obligation with respect to this express warranty shall be (at 3Com’s discretion) to refund the purchase price paid by Customer for any

defective software product, or to replace any defective media with software which substantially conforms to applicable 3Com published

specifications. 3Com makes no warranty or representation that its software products will meet Customer’s requirements or will work in

combination with any hardware or applications software products provided by third parties, that the operation of the software products will be

uninterrupted or error free, or that all defects in the software products will be corrected.

YEAR 2000 WARRANTY: In addition to the Hardware Warranty and Software Warranty stated above, 3Com warrants that the following date-

data sensitive Palm Computing

products, namely the Pilot 1000, Pilot 5000, PalmPilot™ Personal Edition, PalmPilot Professional Edition, Palm

III™, Palm IIIx™, Palm V™, and Palm VII™ connected organizers, as well as all other 3Com products based on the Palm Computing platform

software as of July 1, 1998 and later, including the companion desktop software for Microsoft

Windows

and MAC OS™ platforms, will continue

performing properly with regard to such date-data on and after January 1, 2000, provided that all other products used by Customer in connection

or combination with the Palm Computing product, including hardware, software, and firmware, accurately exchange date-data with the Palm

Computing product. 3Com makes no certification regarding the Year 2000 status of any other Palm Computing products.

Any Palm Computing platform application supplied by 3Com that makes correct use of Palm Computing platform date and time functions will not

have a problem transitioning to the year 2000. The date and time utilities for the Palm Computing platform use 32 bits to store seconds, starting at

January 1, 1904. This approach allows the correct representation of dates through February 5, 2040. The Date Book software currently displays

dates through December 31, 2031. Provided the product is still being sold by 3Com, 3Com will make software enhancements to remove these

limitations well in advance of these dates.

If it appears that any Palm Computing product does not perform properly with regard to such date-data on and after January 1, 2000, and

Customer notifies Palm Computing before the later of April 1, 2000, or ninety (90) days after original purchase of the product from 3Com or its

authorized reseller, 3Com shall, at its option and expense, provide a software update which would effect the proper performance of the product,

repair the product, deliver to Customer an equivalent product to replace the product, or, if none of the foregoing is feasible, refund to Customer the

purchase price paid for the product.

Any software update or replaced or repaired Palm Computing product will carry a Year 2000 Limited Warranty for ninety (90) days after purchase

or until April 1, 2000, whichever is later.

Customers using date and time utilities other than those supplied by Palm Computing should check with the developer to determine if the

software will correctly handle all of the subtle issues of date and time conversion.

OBTAINING WARRANTY SERVICE: Customer must contact a Palm Computing, Inc. or 3Com Technical Support or Customer Service center

within the applicable warranty period to obtain warranty service authorization. Dated proof of original purchase from 3Com or its authorized

reseller will be required. 3Com is not responsible for Customer products or parts received without a warranty service authorization. In the United

States, 3Com may ship a replacement product or part prior to receiving the original product or part (“advance exchange”). If advance exchange is

not available, then the repaired product or part will be shipped as soon as reasonably possible, which will be no later than thirty (30) days after

3Com receives the original product or part. Repaired or replacement products will be shipped to Customer at 3Com’s expense. The repair and

replacement process for products or parts in locations outside of the United States will vary depending on Customer’s location.

Products or parts shipped by Customer to 3Com must be sent prepaid and packaged appropriately for safe shipment, and it is recommended that

they be insured or sent by a method that provides for tracking of the package. When an advance exchange is provided and Customer fails to return

the original product or part to 3Com within thirty (30) days from the date the warranty service authorization is issued, 3Com will charge Customer

the then-current published catalogue price of such product or part.

WARRANTIES EXCLUSIVE:

IF THIS PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY FOR BREACH OF THAT

WARRANTY SHALL BE REPLACEMENT OR REPAIR OF THE PRODUCT OR PART OR REFUND OF THE PURCHASE PRICE PAID, AT 3COM’S OPTION. TO

THE FULL EXTENT ALLOWED BY LAW, THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES,

TERMS, OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES,

TERMS, OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, SATISFACTORY QUALITY, CORRESPONDENCE WITH

DESCRIPTION, AND NON-INFRINGEMENT, ALL OF WHICH ARE EXPRESSLY DISCLAIMED. 3COM NEITHER ASSUMES NOR AUTHORIZES ANY OTHER

PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS.

3COM SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT OR MALFUNCTION

IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER INSTALLATION OR

TESTING, UNAUTHORIZED ATTEMPTS TO OPEN, REPAIR, OR MODIFY THE PRODUCT, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED

USE, OR BY ACCIDENT, FIRE, LIGHTNING, OTHER HAZARDS, OR ACTS OF GOD. THIS WARRANTY DOES NOT COVER PHYSICAL DAMAGE TO THE

SURFACE OF THE PRODUCT, INCLUDING CRACKS OR SCRATCHES ON THE LCD TOUCHSCREEN OR OUTSIDE CASING. THIS WARRANTY DOES NOT

APPLY WHEN THE MALFUNCTION RESULTS FROM THE USE OF THIS PRODUCT IN CONJUNCTION WITH ACCESSORIES, OTHER PRODUCTS, OR

ANCILLARY OR PERIPHERAL EQUIPMENT AND 3COM DETERMINES THAT THERE IS NO FAULT WITH THE PRODUCT ITSELF. THIS WARRANTY DOES

NOT APPLY TO ANY MALFUNCTION OR FAILURE OF THE PRODUCT OR PART DUE TO ANY COMMUNICATION SERVICE CUSTOMER MAY SUBSCRIBE

TO OR USE WITH THE PRODUCT.

LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW, 3COM ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY,

WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE

DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, OR OTHER FINANCIAL

LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF

THIS PRODUCT, EVEN IF 3COM OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS

LIABILITY TO REPLACEMENT, REPAIR, OR REFUND OF THE PURCHASE PRICE PAID, AT 3COM’S OPTION. THIS DISCLAIMER OF LIABILITY FOR

DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.

DISCLAIMER: Some countries, states, or provinces do not allow the exclusion or limitation of implied warranties or the limitation of incidental or

consequential damages for certain products supplied to consumers, or the limitation of liability for personal injury, so the above limitations and

exclusions may be limited in their application to you. When the implied warranties are not allowed to be excluded in their entirety, they will be

limited to the duration of the applicable written warranty. This warranty gives you specific legal rights which may vary depending on local law.

GOVERNING LAW: This Limited Warranty shall be governed by the laws of the State of California, U.S.A. excluding its conflicts of laws

principles and excluding the United Nations Convention on Contracts for the International Sale of Goods.

Palm Computing, Inc., a subsidiary of 3Com Corporation

5400 Bayfront Plaza

PO Box 58007

Santa Clara, California 95052-8007

United States of America

(408) 326-5000

May 20, 1999

YOU SHOULD CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS BEFORE USING THIS PRODUCT. IT CONTAINS

SOFTWARE, THE USE OF WHICH IS LICENSED BY PALM COMPUTING, INC., A SUBSIDIARY OF 3COM CORPORATION (COLLECTIVELY,

“3COM”), TO ITS CUSTOMERS FOR THEIR USE ONLY AS SET FORTH BELOW. IF YOU DO NOT AGREE TO THE TERMS AND

CONDITIONS OF THIS AGREEMENT, DO NOT USE THE SOFTWARE. USING ANY PART OF THE SOFTWARE INDICATES THAT YOU

ACCEPT THESE TERMS.

LICENSE: 3Com grants you a nonexclusive license to use the accompanying software program(s) (the “Software”) subject to the terms and

restrictions set forth in this License Agreement. You are not permitted to lease or rent (except under separate mutually agreeable terms set forth in

writing), distribute or sublicense the Software or to use the Software in a time-sharing arrangement or in any other unauthorized manner. Further,

no license is granted to you in the human readable code of the Software (source code). Except as provided below, this License Agreement does

not grant you any rights to patents, copyrights, trade secrets, trademarks, or any other rights in respect to the Software.

The Software is licensed to be used on any personal computer and/or any 3Com product, provided that the Software is used only in connection

with 3Com products. With respect to the Desktop Software, you may reproduce and provide one (1) copy of such Software for each personal

computer or 3Com product on which such Software is used as permitted hereunder. With respect to the Device Software, you may use such

Software only on one (1) 3Com product. Otherwise, the Software and supporting documentation may be copied only as essential for backup or

archive purposes in support of your use of the Software as permitted hereunder. You must reproduce and include all copyright notices and any

other proprietary rights notices appearing on the Software on any copies that you make.

Notwithstanding any other provision of this License Agreement, this License Agreement shall not be deemed to apply to the Adobe

Acrobat

Reader

software or any other applications software licensed to you by third parties that is included on the same media as 3Com’s Software (“Other Software”)

if the Other Software provides that the use of the Other Software is subject to the terms and conditions of the third party’s license agreement.

NO ASSIGNMENT; NO REVERSE ENGINEERING: You may transfer the Software and this License Agreement to another party if the other

party agrees in writing to accept the terms and conditions of this License Agreement. If you transfer the Software, you must at the same time either

transfer all copies of the Software as well as the supporting documentation to the same party or destroy any such materials not transferred. Except

as set forth above, you may not transfer or assign the Software or your rights under this License Agreement.

Modification, reverse engineering, reverse compiling, or disassembly of the Software is expressly prohibited. However, if you are a European

Community (“EC”) resident, information necessary to achieve interoperability of the Software with other programs within the meaning of the EC

Directive on the Legal Protection of Computer Programs is available to you from 3Com upon written request.

EXPORT RESTRICTIONS: You agree that you will not export or re-export the Software or accompanying documentation (or any copies thereof)

or any products utilizing the Software or such documentation in violation of any applicable laws or regulations of the United States or the country

in which you obtained them.

The software covered by this agreement may contain strong data encryption code which cannot be exported outside of the U.S. or Canada. You

agree that you will not export/reexport, either physically or electronically, the encryption software or accompanying documentation without

obtaining written authorization from the U.S. Department of Commerce.

TRADE SECRETS; TITLE: You acknowledge and agree that the structure, sequence and organization of the Software are the valuable trade

secrets of 3Com and its suppliers. You agree to hold such trade secrets in confidence. You further acknowledge and agree that ownership of, and

title to, the Software and all subsequent copies thereof regardless of the form or media are held by 3Com and its suppliers.

UNITED STATES GOVERNMENT LEGEND: The Software is commercial in nature and developed solely at private expense. The Software is

delivered as “Commercial Computer Software” as defined in DFARS 252.227-7014 (June 1995) or as a commercial item as defined in FAR

2.101(a) and as such is provided with only such rights as are provided in this License Agreement, which is 3Com’s standard commercial license

for the Software. Technical data is provided with limited rights only as provided in DFAR 252.227-7015 (Nov. 1995) or FAR 52.227-14 (June

1987), whichever is applicable.

TERM AND TERMINATION: This License Agreement is effective until terminated. You may terminate it at any time by destroying the Software

and documentation together with all copies and merged portions in any form. It will also terminate immediately if you fail to comply with any term

or condition of this License Agreement. Upon such termination you agree to destroy the Software and documentation, together with all copies and

merged portions in any form.

3Com end user software license agreement

GOVERNING LAW: This License Agreement shall be governed by the laws of the State of California as such laws are applied to agreements

entered into and to be performed entirely within California between California residents and by the laws of the United States. You agree that the

United Nations Convention on Contracts for the International Sale of Goods (1980) is hereby excluded in its entirety from application to this

License Agreement.

LIMITED WARRANTY; LIMITATION OF LIABILITY: All warranties and limitations of liability applicable to the Software are as stated on the

Limited Warranty Card or in the product manual accompanying the Software. Such warranties and limitations of liability are incorporated herein in

their entirety by this reference.

SEVERABILITY: In the event any provision of this License Agreement is found to be invalid, illegal or unenforceable, the validity, legality and

enforceability of any of the remaining provisions shall not in any way be affected or impaired and a valid, legal and enforceable provision of

similar intent and economic impact shall be substituted therefor.

ENTIRE AGREEMENT: This License Agreement sets forth the entire understanding and agreement between you and 3Com, supersedes all prior

agreements, whether written or oral, with respect to the Software, and may be amended only in a writing signed by both parties.

Palm Computing, Inc., a subsidiary of 3Com Corporation

5400 Bayfront Plaza

PO Box 58007

Santa Clara, California 95052-8007

United States of America

(408) 326-5000

September 3, 1998

Computing, and PalmConnect are registered trademarks, and the HotSync logo, Palm, the Palm Computing Platform

logo, and Palm V are trademarks of Palm Computing, Inc., 3Com Corporation or its subsidiaries. Other product and

brand names may be trademarks or registered trademarks of their respective owners.

Palm

™

Desktop-

Organizer-Software

Bitte zuerst lesen

Erste Schritte

Einleitung

Mit der Palm™ Desktop-Organizer-Software, dem Palm Computing

Organizer und

dem geeigneten Adapterkabel, erhalten Sie alles, was Sie benötigen, um Ihren Palm-

Organizer an den Macintosh anzuschließen und Informationen auszutauschen.

Wenn Sie einen PowerPC Macintosh besitzen, benötigen Sie ein Macintosh-

Adapterkabel, um die HotSync® Docking-Station an den Drucker- oder Modem-Port

Ihres Macintosh anzuschließen.

Wenn Sie einen iMac, iBook oder G3 Apple Computer mit USB-Unterstützung

besitzen, benötigen Sie ein USB-Adapterkabel und die USB-Treiber vom Hersteller

des Adapters, um die HotSync® Docking-Station an den USB-Port Ihres Computers

anzuschließen.

Hinweis: Als Benutzer eines Computers mit USB-Unterstützung benötigen Sie

folgendes Zubehör, um die Docking-Station an einen iMac, iBook oder

G3 anzuschließen:

• PalmConnect USB Kit

– oder –

• ein USB-Adapterkabel bzw. -Gerät eines Fremdherstellers

(überprüfen Sie die Kompatibilität der Produkte von

Fremdherstellern mit der Palm Desktop-Software.)

In dieser Dokumentation wird davon ausgegangen, daß Sie einen Palm

USB-Adapter besitzen.

Organizer-Paket

Palm-Organizer

Docking-Station

Palm Zubehör

Macintosh-Adapterkabel

PalmConnect

USB Kit

USB-Adapterkabel

Mit der Palm™ Desktop-Software können Sie Adressen, Termine, Aufgaben und

Notizen verwalten. Im Lieferumfang befindet sich außerdem die HotSync

Manager-

Software, mit der Daten zwischen Ihrem Macintosh und Ihrem Handheld-Gerät

übertragen werden.

Hinweis: Falls Sie eine frühere Version der Palm Desktop-Software installiert

haben, führen Sie jetzt einen HotSync

aus, um sicherzustellen, daß

sich die aktuellsten Daten auf Ihrem Handheld-Gerät befinden.

Wenn Sie ein Software-Upgrade durchführen, müssen Sie in jedem Fall

eine vollständige Installation durchführen, um das Update zur HotSync

Manager-Software zu installieren.

Schalten Sie Ihren Macintosh ein.

Installieren Sie die Palm Desktop-Software.

• Zeigen Sie auf das Symbol “Palm™ Desktop Installer”.

• Doppelklicken Sie anschließend auf das Symbol des Palm™ Desktop-

Aktualisierungsprogramms.

• Befolgen Sie die Anleitungen auf dem Bildschirm.

Neustarten des Macintosh nach abgeschlossener Installation.

Palm

™

Desktop-Software installieren

Synchronisieren Sie Ihre Daten.

• Setzen Sie Ihr Handheld-Gerät in die Docking-Station ein, und drücken Sie auf die

HotSync

-Taste.

Herzlichen Glückwunsch!

Sie haben die Installation erfolgreich abgeschlossen und den ersten HotSync -Vorgang

durchgeführt.

Hinweis: Der AC-Adapter wird nur für den Palm V™

Organizer benötigt.

Stellen Sie eine Verbindung her.

• Verbinden Sie den Anschlußadapter (USB/seriell) mit der Docking-Station

(oder dem HotSync-Kabel).

• Verbinden Sie den Anschlußadapter (USB/seriell) mit dem USB-Anschluß

Ihres Macintosh.

USB Macintosh – Herstellen der Verbindung

Schalten Sie den Macintosh aus.

So verbinden Sie die Geräte miteinander.

• Schließen Sie den Macintosh-Adapter an das Kabel

der Docking-Station an.

• Schließen Sie die Docking-Station an den Drucker- oder den Modemanschluß an

der Rückseite des Computers an. Vergessen Sie nicht, an welchen Anschluß Sie die

Docking-Station angeschlossen haben, da Sie diese Information später noch einmal

benötigen.

Schalten Sie den Macintosh ein.

Synchronisieren Sie Ihre Daten.

• Setzen Sie Ihr Handheld-Gerät in die Docking-Station ein,

und drücken Sie auf die HotSync

-Taste.

Herzlichen Glückwunsch!

Sie haben die Installation erfolgreich abgeschlossen und den ersten HotSync -Vorgang

durchgeführt.

Modemanschluß

Druckeranschluß

PowerPC Macintosh – Herstellen der Verbindung

Starten Sie die Palm

™

Desktop-Software.

Doppelklicken Sie auf das Palm

™

Desktop-Symbol im Palm-Ordner.

Klicken Sie zur Eingabe von Daten auf eines der folgenden Palm Desktop-Symbole.

Wenn Sie die Daten mit Hilfe eines HotSync

-Vorgangs mit dem Palm Organizer

synchronisieren, erscheinen sie dort in den entsprechenden Anwendungen:

Hinweise zu den Unterschieden zwischen der Palm Desktop-Software und den Palm-

Organizer-Anwendungen, finden Sie in der Hilfedatei der Palm™ Desktop-Software.

Wenn Sie zuvor mit dem Claris Organizer gearbeitet haben, können Sie nun Ihre Daten

in die Palm Desktop-Software übertragen.

• Fertigen Sie eine Sicherheitskopie der Claris Organizer-Datendatei an.

• Starten Sie Palm Desktop, und wählen Sie „Merge“ im Menü „File“.

• Navigieren Sie zur vorhandenen Claris Organizer-Datendatei, und klicken

Sie auf „Open“.

Die Daten des Claris Organizer befinden sich nun in der Palm Desktop-Datei. Führen

Sie einen HotSync

-Vorgang durch, um die Daten zum Organizer zu übertragen.

Palm

™

Desktop-Software starten

Kalender Adressen Aufgabenliste Merkzettel

Palm Desktop Software

Handheld-Anwendungen

Appointments Contacts Tasks Notes

Daten vom Claris Organizer migrieren

Anwendungen auf dem Organizer installieren

Sie können die Fähigkeiten des Organizers auf einfache Art und Weise erweitern,

indem Sie Freeware, Shareware oder kommerzielle Anwendungen aus dem Internet

herunterladen, die dort vielfach zur Verfügung stehen. Gehen Sie dazu

folgendermaßen vor:

Laden Sie Anwendungen von www.palm.com

(oder einer anderen Web-Site) herunter.

Entpacken Sie gegebenenfalls die Anwendung. Falls noch nicht vorhanden,

müssen Sie „UnStuffIt“ oder eine Anwendung zum Entpacken von Dateien wie z. B.

„ZipIt“ herunterladen.

Wählen Sie die zu installierende Anwendung.

• Doppelklicken Sie auf das HotSync

Manager-Symbol im Palm-Ordner.

• Wählen Sie „Install“ im Menü „HotSync

“.

• Ziehen Sie die Anwendungsdateien in das Dialogfeld „Install Palm Applications“.

Führen Sie einen HotSync

-Vorgang durch, um die Anwendungen zum Palm-

Organizer zu übertragen.

Die Conduits von Palm Computing

und anderen Softwareanbietern ermöglichen Ihnen

die Synchronisation von Informationen zwischen mehreren Anwendungen auf dem

Palm-Organizer und dem Macintosh.

So installieren Sie einen Conduit:

Ziehen Sie die Conduit-Datei(en) in den Conduits-Ordner, der sich im Palm-

Ordner befindet.

Konfigurieren Sie den Conduit in der HotSync

Manager-Anwendung.

• Doppelklicken Sie auf das HotSync

Manager-Symbol im Palm-Ordner.

• Wählen Sie „Conduit Settings“ im Menü „HotSync

“.

• Konfigurieren Sie den Conduit entsprechend.

Führen Sie einen HotSync

-Vorgang durch, damit der Conduit verwendet wird.

Conduits installieren

Wie aktualisiere ich meinen Macintosh mit der neuesten MacOS?

Gehen Sie zur Apple Website unter http://www.apple.com. Hier finden Sie Hinweise

zur Aktualisierung mit der neuesten MacOS-Version.

Warum kann ich nach dem Einstecken meines Anschlußadapters

(USB/seriell) keinen HotSync

-Vorgang durchführen?

Die Einstellungen des seriellen Anschlusses müssen geändert werden. Führen Sie

dazu die folgenden Schritte aus:

1. Überprüfen Sie die Verbindungen des Anschlußadapters.

2. Starten Sie den HotSync Manager.

3. Deaktivieren Sie den HotSync Manager.

4. Klicken Sie auf die Registerkarte „Serial Port Settings“.

5. Wählen Sie in „Local Setup“ „PalmConnect USB“ in der Liste der Anschlüsse.

– oder –

Wählen Sie in der Liste der Anschlüsse den entsprechenden Eintrag, wenn Sie ein

Adapterkabel eines Fremdherstellers verwenden.

6. Klicken Sie auf die Registerkarte „HotSync Controls“, und wählen Sie „Enabled“.

7. Versuchen Sie, einen HotSync-Vorgang durchzuführen.

Warum erhalte ich eine Fehlermeldung, wenn ich den Anschlußadapter

entferne und den Macintosh neu starte?

Der HotSync Manager unterstützt nicht alle USB-Plug & Play-Funktionen. Ist die

Verbindung zum Anschlußadapter zeitweise unterbrochen, erhalten Sie folgende

Fehlermeldung: „HotSync Manager has been disabled because the USB cable is not

plugged into your Macintosh. Please reconnect the cable to the USB port before

enabling HotSync Manager.“ Klicken Sie zum Fortfahren auf „OK“. Um zu verhindern,

daß diese Meldung während des Neustarts erneut angezeigt wird, starten Sie HotSync

Manager, wählen Sie „Setup“, deaktivieren Sie HotSync Manager, und ziehen Sie

anschließend das Adapterkabel heraus.

Hinweis: Weitere Tips zur Fehlerbehebung finden Sie in der Hilfedatei der Palm™

Desktop-Software.

Tips für die Fehlerbehebung auf dem Macintosh

La page charge ...

Palm Desktop Organizer Read This First Manual

Marque: Palm

Modèle: Desktop Organizer

Taper: Read This First Manual

Télécharger le PDF

rapport

Palm Desktop Organizer Read This First Manual

Palm Desktop Organizer Read This First Manual

dans d''autres langues

Documents connexes

Autres documents