Apollo 51000-305 Guide d'installation

Catégorie
Détecteurs de monoxyde de carbone (CO)
Taper
Guide d'installation
51000-305
Wireless Carbon Monoxide Alarm
Installation Guide
Attention: This manual should be read prior to use and retained for further
information.
GENERAL INFORMATION
The Wireless Carbon Monoxide Alarm is a 3V battery powered wireless
detector intended for use with a compatible wireless alarm system. The
detector consists of an electrochemical carbon monoxide sensor assembly
coupled to a wireless transmitter. The Wireless Carbon Monoxide Alarm
communicates with the control panel and can send alarm, tamper and
battery condition messages to the system’s receiver. Refer to the wireless
system’s instruction for the maximum number of transmitters that can be
supported.
IMPORTANT: This detector must be tested and maintained regularly
following NFPA 720 requirements.
This device is designed to protect individuals from the acute effects of
carbon monoxide exposure. It will not fully safeguard individuals with
specic medical conditions. If in doubt consult a medical practitioner.
WARNING
This product is intended for use in ordinary indoor residential areas. It is
not designed to measure compliance with Occupational Safety & Health
Administration (OSHA) commercial and industrial standards.
Contents of box:
• Wireless Carbon Monoxide Alarm with base
• Installation guide
• Pack of screws and anchors
• Labels as appropriate
• 1 CR123A Panasonic battery
!
2
APD0602 A140513 Wireless CO Install
The Wireless Carbon Monoxide Alarm contains a sounder which generates
the ANSI S3.41 temporal 4 pattern in an alarm condition (see Table 1 for
temporal 4 pattern). In alarm, a message is also sent to the control panel
and the detector’s ID is displayed at the console. During an alarm condition,
pressing the detector’s hush button will silence the sounder for ve minutes.
The mounting base installation is simplied by the incorporation of features
compatible for both drywall fasteners (not supplied) and other methods.
Tricolored LED (green, yellow, red) and a sounder on the detector provide
local visual and audible indication of the detector’s status as listed in Table 1.
During initial power-up the LED blinks alternately green, yellow then red. It
takes about 60 seconds for the detector’s CO sensor to stabilize.
After power-up has completed and the detector is functioning normally, the
green LED blinks once every 12 seconds.
Status LEDs
Sounder
(does not pulse
the sounder and
LED concurrently)
Radio
signalling
Normal
Green ash every
12 seconds
Off
Normal
(None)
Alarm/ Test
Red ash every
12 seconds
ANSI S3.41
temporal 4 (press
button to hush
for 5 minutes)
Alarm
Detector
trouble
Yellow ash
every 6 seconds
One 100ms chirp
every 45 seconds
Fault
Low battery
Yellow ash
every 12 seconds
One 100ms chirp
every 45 seconds
(press button
to hush for 12
hours)
Low Battery
Detector end
of life
Yellow ash
every 23 seconds
One 100ms chirp
every 45 seconds
Fault
Powerup
Green, yellow,
red ash
sequence every
12 seconds
One 100ms chirp
at end of power-
up sequence
None
Tamper
Green, yellow,
red ash
sequence every
12 seconds
Off Tamper
Table 1. Detector status and indication
3
APD0602 A140513 Wireless CO Install
Status LEDs
Sounder
(does not pulse
the sounder and
LED concurrently)
Radio
signalling
Normal
Green ash every
12 seconds
Off
Normal
(None)
Alarm/ Test
Red ash every
12 seconds
ANSI S3.41
temporal 4 (press
button to hush
for 5 minutes)
Alarm
Detector
trouble
Yellow ash
every 6 seconds
One 100ms chirp
every 45 seconds
Fault
Low battery
Yellow ash
every 12 seconds
One 100ms chirp
every 45 seconds
(press button
to hush for 12
hours)
Low Battery
Detector end
of life
Yellow ash
every 23 seconds
One 100ms chirp
every 45 seconds
Fault
Powerup
Green, yellow,
red ash
sequence every
12 seconds
One 100ms chirp
at end of power-
up sequence
None
Tamper
Green, yellow,
red ash
sequence every
12 seconds
Off Tamper
Detector Trouble: When the sensor supervision is in trouble condition,
the yellow LED blinks once every six seconds and there is a chirp every 45
seconds. After 12 hours the panel will display a loss of supervision message.
Detector end of life feature: When the detector has reached the end of its life,
the yellow LED blinks once every 23 seconds and there is a chirp every 45
seconds. After 12 hours the panel will display a loss of supervision message.
This indicates that the CO sensor inside the detector has passed the end of
its life and the detector must be replaced. The detector lifespan is ve years
from the date of manufacture. Refer to DETECTOR REPLACEMENT section.
Low Battery Detection: The Wireless Carbon Monoxide Alarm is powered
by a single 3-volt CR123A Panasonic Lithium battery (included). The
detector regularly checks for a low battery. If a low battery is detected,
the transmitter sends a low battery message to the control panel, which
displays the detector’s ID at low battery. In addition, the yellow LED of the
detector will blink every 12 seconds. The detector’s sounder will chirp every
45 seconds (yellow LED continues to blink) until the battery is replaced.
Pressing the hush button will silence the chirps for 12 hours, if no other
trouble conditions exist. The battery should be replaced WHEN the chirps
begin. Be sure to replace the battery with a fresh one.
This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: 1. This device may not cause harmful
interference, and 2. This device must accept any interference received,
including interference that may cause undesired operation.
Unauthorized changes or modications could void the user’s authority to
operate the equipment.
BATTERY INSTALLATION AND REPLACEMENT
To replace the battery:
1. Remove the detector from its mounting base by twisting the detector
counterclockwise. Remove and dispose of the battery according to
your local regulations.
2. 2. To ensure proper power-down sequence, wait a minimum of 20
seconds before installing new battery.
3. Install a new 3-volt CR123A Panasonic Lithium battery (available from
your Panasonic dealer) in the battery compartment. Follow the polarity
diagram inside the compartment. If the battery is incorrectly inserted
please remove gently with a non-conductive tool and correctly reinsert.
4. Reinstall the detector onto the mounting base by turning the detector
clockwise.
5. After the power-up sequence the green LED should blink about once
every 12 seconds to indicate normal operation. If the battery is not
4
APD0602 A140513 Wireless CO Install
Attention: This manual should be read prior to use
and retained for further information.
51000-305
Wireless Carbon Monoxide Alarm
Installation Guide
GENERAL INFORMATION
The Wireless Carbon Monoxide Alarm is a 3V battery powered wireless
detector intended for use with a compatible wireless alarm system.
The detector consists of an electrochemical carbon monoxide sensor assembly
coupled to a wireless transmitter. The Wireless Carbon Monoxide Alarm commu-
nicates with the control panel and can send alarm, tamper and battery condition
messages to the systems receiver. Refer to the wireless systems instruction for
the maximum number of transmitters that can be supported.
IMPORTANT: This detector must be tested and maintained regularly following
NFPA 720 requirements.
This device is designed to protect individuals from the acute effects of carbon
monoxide exposure. It will not fully safeguard individuals with speci c medical
conditions. If in doubt consult a medical practitioner.
WARNING
This product is intended for use in ordinary indoor residential areas. It is not
designed to measure compliance with Occupational Safety & Health
Administration (OSHA) commercial and industrial standards.
Contents of box:
- Wireless Carbon Monoxide Alarm with base
- Installation guide
- Pack of screws and xings
- Stickers as appropriate
- 1 CR123A Panasonic battery
The Wireless Carbon Monoxide Alarm contains a sounder which generates the ANSI
S3.41 temporal 4 pattern in an alarm condition (see Table 1 for temporal 4 pattern).
In alarm, a message is also sent to the control panel and the detectors ID is displayed at
t h e c o nso l e . D u r i n g a n a l a r m c o n di t i o n , p r e s si n g t h e d et e c t o r s h u s h b u t t o n w i l l s i l e n c e
the sounder for ve m i n ut e s . T h e m o u nt i n g b as e i n st a ll a t i o n i s s i m pli ed by the incorpo-
r a t i o n o f f e a t u r e s c o m p a t i b l e f o r b o t h d r y w a l l f a s t e n e r s ( n o t s u p p l i e d ) a n d o t h e r m e t h o d s .
Tricolored LED (green, yellow, red) and a sounder on the detector provide local
visual and audible indication of the detectors status as listed in Table 1.
During initial power-up the LED blinks alternately green, yellow then red.
It takes about 60 seconds for the detectors CO sensor to stabilize.
After power-up has completed and the detector is functioning normally, the green
LED blinks once every 12 seconds.
Table 1. Detector status and indication
Detector Trouble: When the sensor supervision is in trouble condition, the yellow
LED blinks once every six seconds and there is a chirp every 45 seconds. After
12 hours the panel will display a loss of supervision message.
Detector end of life feature: When the detector has reached the end of its life,
the yellow LED blinks once every 23 seconds and there is a chirp every
45 seconds. After 12 hours the panel will display a loss of supervision message.
This indicates that the CO sensor inside the detector has passed the end of its life
and the detector must be replaced. The detector lifespan is ve years from
the date of manufacture. Refer to DETECTOR REPLACEMENT section.
Low Battery Detection: The Wireless Carbon Monoxide Alarm is powered by
a single 3-volt CR123A Panasonic Lithium battery (included). The detector regu-
larly checks for a low battery. If a low battery is detected, the transmitter sends
a low battery message to the control panel, which displays the detectors ID at
low battery. In addition, the yellow LED of the detector will blink every 12 seconds.
The detectors sounder will chirp every 45 seconds (yellow LED continues to
blink) until the battery is replaced. Pressing the hush button will silence the chirps
for 12 hours, if no other trouble conditions exist. The battery should be replaced
WHEN the chirps begin. Be sure to replace the battery with a fresh one.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: 1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
Unauthorized changes or modi cations could void the users authority to operate
the equipment.
BATTERY INSTALLATION AND REPLACEMENT
To replace the battery:
1. Remove the detector from its mounting base by twisting the detector counter-
clockwise. Remove and dispose of the battery according to your local regulations.
2. To ensure proper power-down sequence, wait a minimum of 20 seconds before
installing new battery.
3. Install a new 3-volt CR123A Panasonic Lithium battery (available from your
Panasonic dealer) in the battery compartment. Follow the polarity diagram inside
the compartment. If the battery is incorrectly inserted please remove gently with a
non-conductive tool and correctly reinsert.
4. Reinstall the detector onto the mounting base by turning the detector clockwise.
5. After the power-up sequence the green LED should blink about once every
12 seconds to indicate normal operation. If the battery is not installed correctly, the
detector will not operate and the battery may be damaged. If the detector does not
power-up, check for correct battery installation and for a fully charged battery.
CONSTANT EXPOSURES TO HIGH OR LOW TEMPERATURES OR HIGH
HUMIDITY MAY REDUCE BATTERY LIFE.
COMPARTIMENT DE LA BATTERIE
Fig 1. Wireless Carbon Monoxide Alarm
PROGRAMMING
Refer to the appropiate compatible control panel programming guide for the proper
procedure required to enroll the wireless carbon monoxide alarm into the system.
MOUNTING THE DETECTOR
Note: These alarm devices should only be installed and commissioned by a com-
petent engineer/technician.
First, determine the best location for the detector, one that provides proper carbon
monoxide detection (see Figure 2 for suggested detection locations) .
Proper Carbon Monoxide Detection Location
Wall-mounted detectors should be positioned at least as high as a light switch,
and at least six inches (15cm) from the ceiling. In a ceiling location, the detector
should be at least 12 inches (30cm) from any wall.
Where to install, ideally:
- Within 10 feet (3m) of a sleeping area
- Inside the bedroom if it contains a fuel burning appliance
- On every oor of the building
- Ideally, install in any room that contains a fuel burning appliance
- If the appliance or the room is not normally used, such as the boiler room,
the detector should be placed just outside the room so the alarm can be heard
more easily
Where NOT to install, ideally:
- Directly above a sink, cooker, stove or oven
- Do not locate detector within 5 feet (1.5m) of any cooking appliance
- Next to a door or window that would be affected by drafts i.e. extractor fan or air
vent
- Outside
- Do not install in any environment that does not comply with the detectors environ-
mental speci cations
- In or below a cupboard
- Where air ow would be obstructed by curtains or furniture
- Where dirt or dust could collect and block the sensor
- Where it could be knocked, damaged, or inadvertently removed
Fig 2. Detector Location Diagram
Mounting Procedure
Once a suitable location is found, mount the detector as follows:
1. Refer to the diagram below and install the mounting base on the ceiling or on
the wall (if local ordinances permit) using screw locations as required. Use the two
screws and anchors provided. Maneuver the base so the screws are at the elbow
of the screw slots and secure.
2. Fit the detector inside the base by aligning it over the base as shown (detectors
alignment notch should be slightly offset from mounting base tamper release tab),
Status LEDs
Sounder
(does not pulse the
sounder
and LED concurrently)
Radio
signalling
Normal
Green ash every 12
seconds
Off
Normal
(None)
Alarm/
Test
Red ash every 12 seconds
ANSI S3.41 temporal 4
(press button to hush for 5
minutes)
Alarm
Detector
trouble
Yellow ash every 6
seconds
One 100ms chirp every 45
seconds
Fault
Low
battery
Yellow ash every 12
seconds
One 100ms chirp every 45
seconds (press button to
hush for 12 hours)
Low
Battery
Detector
end of
life
Yellow ash every 23
seconds
One 100ms chirp every 45
seconds
Fault
Power-
up
Green, yellow, red ash se-
quence every 12 seconds
One 100ms chirp at end of
power-up sequence
None
Tamper
Green, yellow, red ash se-
quence every 12 seconds
Off Tamper
CHAMBRE
CHAMBRE CHAMBRE
SALONCUISINE
CAVE
PORTES
FERMÉES
GARAGE
À CH
EMPLACEMENT DE L’ALARME DE MONOXYDE DE CARBONE POUR UN DOMICILE
À PLUSIEURS ÉTAGES
INST APD0602 A140513
Attention: This manual should be read prior to use
and retained for further information.
51000-305
Wireless Carbon Monoxide Alarm
Installation Guide
GENERAL INFORMATION
The Wireless Carbon Monoxide Alarm is a 3V battery powered wireless
detector intended for use with a compatible wireless alarm system.
The detector consists of an electrochemical carbon monoxide sensor assembly
coupled to a wireless transmitter. The Wireless Carbon Monoxide Alarm commu-
nicates with the control panel and can send alarm, tamper and battery condition
messages to the systems receiver. Refer to the wireless systems instruction for
the maximum number of transmitters that can be supported.
IMPORTANT: This detector must be tested and maintained regularly following
NFPA 720 requirements.
This device is designed to protect individuals from the acute effects of carbon
monoxide exposure. It will not fully safeguard individuals with speci c medical
conditions. If in doubt consult a medical practitioner.
WARNING
This product is intended for use in ordinary indoor residential areas. It is not
designed to measure compliance with Occupational Safety & Health
Administration (OSHA) commercial and industrial standards.
Contents of box:
- Wireless Carbon Monoxide Alarm with base
- Installation guide
- Pack of screws and xings
- Stickers as appropriate
- 1 CR123A Panasonic battery
The Wireless Carbon Monoxide Alarm contains a sounder which generates the ANSI
S3.41 temporal 4 pattern in an alarm condition (see Table 1 for temporal 4 pattern).
In alarm, a message is also sent to the control panel and the detectors ID is displayed at
t h e c o n s o l e. D u r i n g a n a l a r m c o n d i t i o n , p r e s s i n g t h e d e t e c t o r s h u s h b u t to n w i l l s i l en c e
the sounder for ve m i n ut e s . T h e m o u nt in g b a s e i n s t a l l at i o n i s s i m p l i ed by the incorpo-
r a t i o n o f f e a t u r e s c o m p a t i b l e f o r b o t h d r y w a l l f a s t e n e r s (n o t s u p p l i e d ) a n d o t h e r m e t h o d s .
Tricolored LED (green, yellow, red) and a sounder on the detector provide local
visual and audible indication of the detectors status as listed in Table 1.
During initial power-up the LED blinks alternately green, yellow then red.
It takes about 60 seconds for the detectors CO sensor to stabilize.
After power-up has completed and the detector is functioning normally, the green
LED blinks once every 12 seconds.
Table 1. Detector status and indication
Detector Trouble: When the sensor supervision is in trouble condition, the yellow
LED blinks once every six seconds and there is a chirp every 45 seconds. After
12 hours the panel will display a loss of supervision message.
Detector end of life feature: When the detector has reached the end of its life,
the yellow LED blinks once every 23 seconds and there is a chirp every
45 seconds. After 12 hours the panel will display a loss of supervision message.
This indicates that the CO sensor inside the detector has passed the end of its life
and the detector must be replaced. The detector lifespan is ve years from
the date of manufacture. Refer to DETECTOR REPLACEMENT section.
Low Battery Detection: The Wireless Carbon Monoxide Alarm is powered by
a single 3-volt CR123A Panasonic Lithium battery (included). The detector regu-
larly checks for a low battery. If a low battery is detected, the transmitter sends
a low battery message to the control panel, which displays the detectors ID at
low battery. In addition, the yellow LED of the detector will blink every 12 seconds.
The detectors sounder will chirp every 45 seconds (yellow LED continues to
blink) until the battery is replaced. Pressing the hush button will silence the chirps
for 12 hours, if no other trouble conditions exist. The battery should be replaced
WHEN the chirps begin. Be sure to replace the battery with a fresh one.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: 1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
Unauthorized changes or modi cations could void the users authority to operate
the equipment.
BATTERY INSTALLATION AND REPLACEMENT
To replace the battery:
1. Remove the detector from its mounting base by twisting the detector counter-
clockwise. Remove and dispose of the battery according to your local regulations.
2. To ensure proper power-down sequence, wait a minimum of 20 seconds before
installing new battery.
3. Install a new 3-volt CR123A Panasonic Lithium battery (available from your
Panasonic dealer) in the battery compartment. Follow the polarity diagram inside
the compartment. If the battery is incorrectly inserted please remove gently with a
non-conductive tool and correctly reinsert.
4. Reinstall the detector onto the mounting base by turning the detector clockwise.
5. After the power-up sequence the green LED should blink about once every
12 seconds to indicate normal operation. If the battery is not installed correctly, the
detector will not operate and the battery may be damaged. If the detector does not
power-up, check for correct battery installation and for a fully charged battery.
CONSTANT EXPOSURES TO HIGH OR LOW TEMPERATURES OR HIGH
HUMIDITY MAY REDUCE BATTERY LIFE.
COMPARTIMENT DE LA BATTERIE
Fig 1. Wireless Carbon Monoxide Alarm
PROGRAMMING
Refer to the appropiate compatible control panel programming guide for the proper
procedure required to enroll the wireless carbon monoxide alarm into the system.
MOUNTING THE DETECTOR
Note: These alarm devices should only be installed and commissioned by a com-
petent engineer/technician.
First, determine the best location for the detector, one that provides proper carbon
monoxide detection (see Figure 2 for suggested detection locations) .
Proper Carbon Monoxide Detection Location
Wall-mounted detectors should be positioned at least as high as a light switch,
and at least six inches (15cm) from the ceiling. In a ceiling location, the detector
should be at least 12 inches (30cm) from any wall.
Where to install, ideally:
- Within 10 feet (3m) of a sleeping area
- Inside the bedroom if it contains a fuel burning appliance
- On every oor of the building
- Ideally, install in any room that contains a fuel burning appliance
- If the appliance or the room is not normally used, such as the boiler room,
the detector should be placed just outside the room so the alarm can be heard
more easily
Where NOT to install, ideally:
- Directly above a sink, cooker, stove or oven
- Do not locate detector within 5 feet (1.5m) of any cooking appliance
- Next to a door or window that would be affected by drafts i.e. extractor fan or air
vent
- Outside
- Do not install in any environment that does not comply with the detectors environ-
mental speci cations
- In or below a cupboard
- Where air ow would be obstructed by curtains or furniture
- Where dirt or dust could collect and block the sensor
- Where it could be knocked, damaged, or inadvertently removed
Fig 2. Detector Location Diagram
Mounting Procedure
Once a suitable location is found, mount the detector as follows:
1. Refer to the diagram below and install the mounting base on the ceiling or on
the wall (if local ordinances permit) using screw locations as required. Use the two
screws and anchors provided. Maneuver the base so the screws are at the elbow
of the screw slots and secure.
2. Fit the detector inside the base by aligning it over the base as shown (detectors
alignment notch should be slightly offset from mounting base tamper release tab),
Status LEDs
Sounder
(does not pulse the
sounder
and LED concurrently)
Radio
signalling
Normal
Green ash every 12
seconds
Off
Normal
(None)
Alarm/
Test
Red ash every 12 seconds
ANSI S3.41 temporal 4
(press button to hush for 5
minutes)
Alarm
Detector
trouble
Yellow ash every 6
seconds
One 100ms chirp every 45
seconds
Fault
Low
battery
Yellow ash every 12
seconds
One 100ms chirp every 45
seconds (press button to
hush for 12 hours)
Low
Battery
Detector
end of
life
Yellow ash every 23
seconds
One 100ms chirp every 45
seconds
Fault
Power-
up
Green, yellow, red ash se-
quence every 12 seconds
One 100ms chirp at end of
power-up sequence
None
Tamper
Green, yellow, red ash se-
quence every 12 seconds
Off Tamper
CHAMBRE
CHAMBRE CHAMBRE
SALONCUISINE
CAVE
PORTES
FERMÉES
GARAGE
À CH
EMPLACEMENT DE L’ALARME DE MONOXYDE DE CARBONE POUR UN DOMICILE
À PLUSIEURS ÉTAGES
INST APD0602 A140513
Fig 1. Wireless Carbon Monoxide Alarm
installed correctly, the detector will not operate and the battery may be
damaged. If the detector does not power-up, check for correct battery
installation and for a fully charged battery.
CONSTANT EXPOSURES TO HIGH OR LOW TEMPERATURES OR HIGH
HUMIDITY MAY REDUCE BATTERY LIFE.
PROGRAMMING
Refer to the compatible control panel programming guide for the proper
procedure required to enroll the wireless carbon monoxide alarm into the
system.
MOUNTING THE DETECTOR
Note: These alarm devices should only be installed and commissioned by a
competent engineer/technician.
First, determine the best location for the detector, one that provides proper
carbon monoxide detection (see Figure 2 for suggested detection locations).
Proper Carbon Monoxide Detection Location
Wall-mounted detectors should be positioned at least as high as a light
switch, and at least six inches (15cm) from the ceiling. In a ceiling location,
the detector should be at least 12 inches (30cm) from any wall.
Where to install, ideally:
• Within 10 feet (3m) of a sleeping area
• Inside the bedroom if it contains a fuel burning appliance
• On every oor of the building
• Ideally, install in any room that contains a fuel burning appliance
• If the appliance or the room is not normally used, such as the boiler
room, the detector should be placed just outside the room so the alarm
can be heard more easily
5
APD0602 A140513 Wireless CO Install
Mounting Procedure
Once a suitable location is found, mount the detector as follows:
1. Refer to the diagram below and install the mounting base on the ceiling
or on the wall (if local ordinances permit) using screw locations as
required. Use the two screws and anchors provided. Maneuver the
base A the screws are at the elbow of the screw slots and secure.
2. Fit the detector inside the base by aligning it over the base as shown
(detector’s alignment notch should be slightly offset from mounting
base tamper release tab), then turn the detector in a clockwise direction
until it clicks into place.
Attention: This manual should be read prior to use
and retained for further information.
51000-305
Wireless Carbon Monoxide Alarm
Installation Guide
GENERAL INFORMATION
The Wireless Carbon Monoxide Alarm is a 3V battery powered wireless
detector intended for use with a compatible wireless alarm system.
The detector consists of an electrochemical carbon monoxide sensor assembly
coupled to a wireless transmitter. The Wireless Carbon Monoxide Alarm commu-
nicates with the control panel and can send alarm, tamper and battery condition
messages to the systems receiver. Refer to the wireless systems instruction for
the maximum number of transmitters that can be supported.
IMPORTANT: This detector must be tested and maintained regularly following
NFPA 720 requirements.
This device is designed to protect individuals from the acute effects of carbon
monoxide exposure. It will not fully safeguard individuals with speci c medical
conditions. If in doubt consult a medical practitioner.
WARNING
This product is intended for use in ordinary indoor residential areas. It is not
designed to measure compliance with Occupational Safety & Health
Administration (OSHA) commercial and industrial standards.
Contents of box:
- Wireless Carbon Monoxide Alarm with base
- Installation guide
- Pack of screws and xings
- Stickers as appropriate
- 1 CR123A Panasonic battery
The Wireless Carbon Monoxide Alarm contains a sounder which generates the ANSI
S3.41 temporal 4 pattern in an alarm condition (see Table 1 for temporal 4 pattern).
In alarm, a message is also sent to the control panel and the detectors ID is displayed at
t h e c o n s o l e . D u r in g a n a l a r m c o n d i t i o n, p r e s s i n g t h e d e t e c t o r s h u s h b u t to n w i l l s i l e n c e
the sounder for ve m i nu t e s . T h e m o u n t i n g b as e i ns t a l l a t i o n i s s i m p l i ed by the incorpo-
r a t i o n o f f e a t u r e s c o m p a t i b l e f o r b o t h d r y w a l l f a s t e n e r s (n o t s u p p l i e d ) a n d o t h e r m e t h o d s .
Tricolored LED (green, yellow, red) and a sounder on the detector provide local
visual and audible indication of the detectors status as listed in Table 1.
During initial power-up the LED blinks alternately green, yellow then red.
It takes about 60 seconds for the detectors CO sensor to stabilize.
After power-up has completed and the detector is functioning normally, the green
LED blinks once every 12 seconds.
Table 1. Detector status and indication
Detector Trouble: When the sensor supervision is in trouble condition, the yellow
LED blinks once every six seconds and there is a chirp every 45 seconds. After
12 hours the panel will display a loss of supervision message.
Detector end of life feature: When the detector has reached the end of its life,
the yellow LED blinks once every 23 seconds and there is a chirp every
45 seconds. After 12 hours the panel will display a loss of supervision message.
This indicates that the CO sensor inside the detector has passed the end of its life
and the detector must be replaced. The detector lifespan is ve years from
the date of manufacture. Refer to DETECTOR REPLACEMENT section.
Low Battery Detection: The Wireless Carbon Monoxide Alarm is powered by
a single 3-volt CR123A Panasonic Lithium battery (included). The detector regu-
larly checks for a low battery. If a low battery is detected, the transmitter sends
a low battery message to the control panel, which displays the detectors ID at
low battery. In addition, the yellow LED of the detector will blink every 12 seconds.
The detectors sounder will chirp every 45 seconds (yellow LED continues to
blink) until the battery is replaced. Pressing the hush button will silence the chirps
for 12 hours, if no other trouble conditions exist. The battery should be replaced
WHEN the chirps begin. Be sure to replace the battery with a fresh one.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: 1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
Unauthorized changes or modi cations could void the users authority to operate
the equipment.
BATTERY INSTALLATION AND REPLACEMENT
To replace the battery:
1. Remove the detector from its mounting base by twisting the detector counter-
clockwise. Remove and dispose of the battery according to your local regulations.
2. To ensure proper power-down sequence, wait a minimum of 20 seconds before
installing new battery.
3. Install a new 3-volt CR123A Panasonic Lithium battery (available from your
Panasonic dealer) in the battery compartment. Follow the polarity diagram inside
the compartment. If the battery is incorrectly inserted please remove gently with a
non-conductive tool and correctly reinsert.
4. Reinstall the detector onto the mounting base by turning the detector clockwise.
5. After the power-up sequence the green LED should blink about once every
12 seconds to indicate normal operation. If the battery is not installed correctly, the
detector will not operate and the battery may be damaged. If the detector does not
power-up, check for correct battery installation and for a fully charged battery.
CONSTANT EXPOSURES TO HIGH OR LOW TEMPERATURES OR HIGH
HUMIDITY MAY REDUCE BATTERY LIFE.
COMPARTIMENT DE LA BATTERIE
Fig 1. Wireless Carbon Monoxide Alarm
PROGRAMMING
Refer to the appropiate compatible control panel programming guide for the proper
procedure required to enroll the wireless carbon monoxide alarm into the system.
MOUNTING THE DETECTOR
Note: These alarm devices should only be installed and commissioned by a com-
petent engineer/technician.
First, determine the best location for the detector, one that provides proper carbon
monoxide detection (see Figure 2 for suggested detection locations) .
Proper Carbon Monoxide Detection Location
Wall-mounted detectors should be positioned at least as high as a light switch,
and at least six inches (15cm) from the ceiling. In a ceiling location, the detector
should be at least 12 inches (30cm) from any wall.
Where to install, ideally:
- Within 10 feet (3m) of a sleeping area
- Inside the bedroom if it contains a fuel burning appliance
- On every oor of the building
- Ideally, install in any room that contains a fuel burning appliance
- If the appliance or the room is not normally used, such as the boiler room,
the detector should be placed just outside the room so the alarm can be heard
more easily
Where NOT to install, ideally:
- Directly above a sink, cooker, stove or oven
- Do not locate detector within 5 feet (1.5m) of any cooking appliance
- Next to a door or window that would be affected by drafts i.e. extractor fan or air
vent
- Outside
- Do not install in any environment that does not comply with the detectors environ-
mental speci cations
- In or below a cupboard
- Where air ow would be obstructed by curtains or furniture
- Where dirt or dust could collect and block the sensor
- Where it could be knocked, damaged, or inadvertently removed
Fig 2. Detector Location Diagram
Mounting Procedure
Once a suitable location is found, mount the detector as follows:
1. Refer to the diagram below and install the mounting base on the ceiling or on
the wall (if local ordinances permit) using screw locations as required. Use the two
screws and anchors provided. Maneuver the base so the screws are at the elbow
of the screw slots and secure.
2. Fit the detector inside the base by aligning it over the base as shown (detectors
alignment notch should be slightly offset from mounting base tamper release tab),
Status LEDs
Sounder
(does not pulse the
sounder
and LED concurrently)
Radio
signalling
Normal
Green ash every 12
seconds
Off
Normal
(None)
Alarm/
Test
Red ash every 12 seconds
ANSI S3.41 temporal 4
(press button to hush for 5
minutes)
Alarm
Detector
trouble
Yellow ash every 6
seconds
One 100ms chirp every 45
seconds
Fault
Low
battery
Yellow ash every 12
seconds
One 100ms chirp every 45
seconds (press button to
hush for 12 hours)
Low
Battery
Detector
end of
life
Yellow ash every 23
seconds
One 100ms chirp every 45
seconds
Fault
Power-
up
Green, yellow, red ash se-
quence every 12 seconds
One 100ms chirp at end of
power-up sequence
None
Tamper
Green, yellow, red ash se-
quence every 12 seconds
Off Tamper
CHAMBRE
CHAMBRE CHAMBRE
SALONCUISINE
CAVE
PORTES
FERMÉES
GARAGE
À CH
EMPLACEMENT DE L’ALARME DE MONOXYDE DE CARBONE POUR UN DOMICILE
À PLUSIEURS ÉTAGES
INST APD0602 A140513
Fig 2. Detector Location Diagram
Where NOT to install, ideally:
• Directly above a sink, cooker, stove or oven
• Do not locate detector within 5 feet (1.5m) of any cooking appliance
• Next to a door or window that would be affected by drafts i.e. extractor
fan or air vent
• Outside
• Do not install in any environment that does not comply with the
detector’s environmental specications
• In or below a cupboard
• Where air ow would be obstructed by curtains or furniture
• Where dirt or dust could collect and block the sensor
• Where it could be knocked, damaged, or inadvertently removed
6
APD0602 A140513 Wireless CO Install
3. Test the detector after completing the installation (as described in
the TESTING THE DETECTOR section of this manual) and refer to the
control system’s instructions for additional information concerning the
use of wireless devices.
DO NOT attach the detector to removable ceiling panels.
NOTE: Two warning labels are provided in the detector box. Please stick
one next to the CO detector and another near to a source of fresh air where
members of the household will gather if alarm signal sounds.
then turn the detector in a clockwise direction until it clicks into place.
3. Test the detector after completing the installation (as described in the TESTING
THE DETECTOR section of this manual) and refer to the control systems instruc-
tions for additional information concerning the use of wireless devices.
DO NOT attach the detector to removable ceiling panels.
NOTE: Two warning labels are provided in the detector box. Please stick one
next to the CO detector and another near to a source of fresh air where members
of the household will gather if alarm signal sounds.
Fig 3. Installation du détecteur
CAUTION
Airborne dust particles can enter the detector. Apollo recommends the removal
of detectors before beginning construction or any other dust producing activity.
Carbon monoxide detectors are not to be used with detector guards unless the
combination has been evaluated and found suitable for that purpose.
Tamper Protection
This detector has a built-in tamper switch that will cause a Tamper signal to be
displayed at the console of the alarm system if it is removed from its mounting
base.
The Wireless Carbon Monoxide Alarm includes a tamper resistant feature that
prevents removal from the mounting base without the use of a tool. To engage
the tamper resistant feature, cut the small plastic tab located on the mounting
base and then install the detector. To remove the detector from the base once
it has been made tamper resistant, use appropriate screwdriver to depress
the square tamper release tab located on the skirt of the mounting base
and turn the detector counterclockwise.
TESTING THE DETECTOR
NOTE: Before testing, notify the central station that the detector system is under-
going maintenance in order to prevent unwanted alarms. Testing the detector will
activate an alarm and send a signal to the panel. Also, the test function cannot be
used if the detector has a trouble or end-of-life condition.
Detectors must be tested after installation and following periodic maintenance.
Testing Detector Operation
This test checks the detectors sounder, LEDs, and transmitter.
1. The test button is located on the detector housing.
2. Push and hold the test button for a minimum of 5 seconds. The alarm panel
will trigger and then the detector will go into alarm. The sounder begins the
temporal 4 pattern and the red LED blinks. The alarm panels keypad should
display the detectors name in alarm.
CAUTION: Carbon Monoxide Gas and its Detection
This carbon monoxide detector is designed for indoor use only. Do not expose
to rain or moisture. Do not knock or drop the detector. Do not open or tamper with
the detector as this could cause malfunction. The detector will not protect against
the risk of carbon monoxide poisoning if not properly installed.
CAUTION: This device will only indicate the presence of carbon monoxide gas
at the sensor. Carbon monoxide gas may be present in other areas.
This carbon monoxide alarming device is designed to detect carbon monoxide
gas from ANY source of combustion. It is NOT designed to detect smoke, re
or other gases unless the product has been investigated and determined to
comply with applicable requirements.
This device should not be installed as a substitute for proper installation, use,
and maintenance of fuel burning appliances, including appropriate ventilation
and exhaust systems.
Carbon monoxide gas is a highly poisonous gas which is released when fuels
are burned. It is invisible, has no smell and is therefore impossible to detect with
the human senses. Under normal conditions in a room where fuel burning appli-
ances are well maintained and correctly ventilated, the amount of carbon monox-
ide released into the room by appliances should not be dangerous.
Conditions that can result in transient CO situations:
1. Excessive spillage or reverse venting of fuel-burning appliances caused by
- outdoor ambient conditions, such as wind direction and/or velocity,
including high gusts of wind, and insuf cient draft in the vent pipes,
- negative pressure differential resulting from the use of exhaust fans,
- simultaneous operation of several fuel-burning appliances competing
f for limited internal air,
- loose vent pipe connections from fuel- red appliances,
- obstructions, or unconventional vent pipe designs that can amplify
the above situations,
- poorly designed or maintained chimneys and/or vents,
2. Extended operation of unvented fuel-burning devices (range, oven,
replace, etc),
3. Temperature inversions that can trap exhaust gases near the ground,
4. Car idling in an open or closed attached garage, or near a home.
The following symptoms may be related to CARBON MONOXIDE POISONING
and should be discussed with ALL members of the household:
- Mild exposure: Headache, running nose, sore eyes, often described as  u - l i k e
symptoms
- Medium exposure: Dizziness, drowsiness, vomiting
- Extreme exposure: Unconsciousness, brain damage, death
Many causes of reported CARBON MONOXIDE POISONING indicate that while
victims are aware they are not well, they become so disoriented that they are
unable to save themselves by either exiting the building or calling for assistance.
Also, young children and pets may be the rst to be affected.
WARNING: IMPORTANT INFORMATION FOR THE USER
Individuals with medical problems may consider using warning devices which
provide audible and visual signals for carbon monoxide concentrations under
30 ppm.
WARNING
Actuation of this device indicates the presence of carbon monoxide (CO) which
can KILL YOU.
If alarm signal sounds, four beeps:
1. Operate hush/test button.
2. Immediately move to fresh air  outdoors or by an open window.
3. Check all persons are accounted for.
4. Do not re-enter the premises or move away from the open door/window until
the emergency services responders have arrived, the premises have been aired
out, and your alarm remains in its normal condition.
5. Call your emergency local service, re department or 911
6. If service signal sounds, one chirp, then check the service section to try and
correct.
7. After following steps 1-6, if your alarm reactivates within a 24 hour period,
repeat steps 1-6 and call your local quali ed technician to investigate for sources
of CO from fuel burning equipment and appliances and inspect for proper opera-
tion of this equipment. If problems are identi ed during this inspection, have the
equipment serviced immediately. Note any combustion equipment not inspected
by the technician and consult the manufacturers instructions, or contact the
manufacturers directly for more information about CO safety and this equip-
ment. Make sure that motor vehicles are not, and have not been, operating in an
attached garage or adjacent to the residence.
The premises should be well ventilated when household cleaning supplies or
similar contaminants are used.
DETECTOR REPLACEMENT
This detector is manufactured with a long-life carbon monoxide sensor. Over time
the sensor will lose sensitivity, and will need to be replaced with a new carbon
monoxide detector. The detectors lifespan is 5 years from the date of
manufacture.
NOTE: When the detector is removed from its base, a Tamper message is sent to
the central station.
The detector will also cause a trouble condition once it has reached the end of its
useful life. If this occurs, it is time to replace the detector.
NOTE: Before replacing the detector, notify the proper authorities that main-
tenance is being performed and the system will be temporarily out of service.
Disable the zone or system undergoing maintenance to prevent any unwanted
alarms. Dispose of the detector in accordance with any local regulations.
NOTE: The replacement date that appears on the device is the date beyond
which the device may no longer detect carbon monoxide accurately and should
be immediately replaced.
CAUTION
It should be noted the installation, operation, testing and maintenance of the
Wireless Carbon Monoxide Alarm is different than smoke detectors. Per NFPA
720 section 5.3.7.2 the detector shall not be connected to a zone that signals
a re condition (i.e. smoke detectors zones). Therefore, the Wireless Carbon
Monoxide Alarm must be programmed as a non- re zone. See the controls
Installation Instructions for the appropriate carbon monoxide zone type to be
programmed.
SPECIFICATIONS
Power Source: One 3-volt CR123A Panasonic Lithium Battery (included)
Audible Signal (temp 4 tone): 85 dBA min. in alarm (at 10ft (3m))
Operating Current: 10 A
Temperature Range: 40°F (4.4°C) to 100°F (37.8 °C)
Operating Humidity Range: 15% to 95% Relative Humidity, non-condensing
Pending Agency Listings: UL standard 2075, UL 2034 and CSA 6.19-01
Apollo America, Inc.
25 Corporate Drive
Auburn Hills, MI 48326
(248) 332-3900 Phone/Tech
support
www.apollo-fire.com
CAUTION
Airborne dust particles can enter the detector. Apollo recommends the
removal of detectors before beginning construction or any other dust
producing activity. Carbon monoxide detectors are not to be used with
detector guards unless the combination has been evaluated and found
suitable for that purpose.
Tamper Protection
This detector has a built-in tamper switch that will cause a Tamper signal
to be displayed at the console of the alarm system if it is removed from its
mounting base.
The Wireless Carbon Monoxide Alarm includes a tamper resistant feature
that prevents removal from the mounting base without the use of a tool.
To engage the tamper resistant feature, cut the small plastic tab located on
the mounting base and then install the detector. To remove the detector
from the base once it has been made tamper resistant, use appropriate
7
APD0602 A140513 Wireless CO Install
screwdriver to depress the square tamper release tab located on the skirt of
the mounting base and turn the detector counterclockwise.
TESTING THE DETECTOR
NOTE: Before testing, notify the central station that the detector system
is undergoing maintenance in order to prevent unwanted alarms. Testing
the detector will activate an alarm and send a signal to the panel. Also, the
test function cannot be used if the detector has a trouble or end-of-life
condition.
Detectors must be tested after installation and following periodic
maintenance.
Testing Detector Operation
This test checks the detector’s sounder, LEDs, and transmitter.
1. The test button is located on the detector housing.
2. Push and hold the test button for a minimum of 5 seconds. The alarm
panel will trigger and then the detector will go into alarm. The sounder
begins the temporal 4 pattern and the red LED blinks. The alarm panel’s
keypad should display the detector’s name in alarm.
CAUTION: Carbon Monoxide Gas and its Detection
This carbon monoxide detector is designed for indoor use only. Do not
expose to rain or moisture. Do not knock or drop the detector. Do not
open or tamper with the detector as this could cause malfunction. The
detector will not protect against the risk of carbon monoxide poisoning if
not properly installed.
CAUTION: This device will only indicate the presence of carbon monoxide
gas at the sensor. Carbon monoxide gas may be present in other areas.
This carbon monoxide alarming device is designed to detect carbon
monoxide gas from ANY source of combustion. It is NOT designed to
detect smoke, re or other gases unless the product has been investigated
and determined to comply with applicable requirements.
This device should not be installed as a substitute for proper installation,
use, and maintenance of fuel burning appliances, including appropriate
ventilation and exhaust systems.
Carbon monoxide gas is a highly poisonous gas which is released when
fuels are burned. It is invisible, has no smell and is therefore impossible to
detect with the human senses. Under normal conditions in a room where
fuel burning appliances are well maintained and correctly ventilated, the
amount of carbon monoxide released into the room by appliances should
not be dangerous.
8
APD0602 A140513 Wireless CO Install
Conditions that can result in transient CO situations:
1. Excessive spillage or reverse venting of fuel-burning appliances caused
by
• outdoor ambient conditions, such as wind direction and/or velocity,
including high gusts of wind, and insufcient draft in the vent pipes,
• negative pressure differential resulting from the use of exhaust fans,
• simultaneous operation of several fuel-burning appliances competing
for limited internal air,
• loose vent pipe connections from fuel-red appliances,
• obstructions, or unconventional vent pipe designs that can amplify
the above situations,
• poorly designed or maintained chimneys and/or vents,
2. Extended operation of unvented fuel-burning devices (range, oven,
replace, etc),
3. Temperature inversions that can trap exhaust gases near the ground,
4. Car idling in an open or closed attached garage, or near a home.
The following symptoms are related to CARBON MONOXIOE POISONING
and are to be discussed with All members of the household;
1. Mild Exposure: Slight headache, nausea, vomiting, fatigue (often
described as "Flulike" symptoms).
2. Medium Exposure: Severe throbbing headache, drowsiness, confusion,
fast heart rate.
3. Extreme Exposure: Unconsciousness, convulsions, cardiorespiratory
failure, death.
4. Many cases of reported CARBON MONOXIDE POISONING indicate that
while victims are aware they are not well, they become so disoriented
they are unable to save themselves by either exiting the building or
calling for assistance. Young children and household pets are typically
the rst affected.
WARNING: IMPORTANT INFORMATION FOR THE USER
Individuals with medical problems may consider using warning
devices which provide audible and visual signals for carbon monoxide
concentrations under 30 ppm.
WARNING
Actuation of your CO alarm indicates the presence of carbon monoxide
(CO) which can KILL YOU. If alarm signal sounds:
1. Operate reset/silence button.
2. Call your emergency services (Telephone Number) (fire
department or 911).
3. lmmediately move to fresh air - outdoors or by an open
!
!
9
APD0602 A140513 Wireless CO Install
door/window. Do a head count to check that all persons
are accounted for. Do not reenter the premises nor move
away from the open door/window until the emergency
services responders have arrived, the premises have been
aired out, and your alarm remains in its normal condition.
4. After following steps 1 - 3, if your alarm reactivates within
a 24 hour period, repeat steps 1 - 3 and call a qualified
appliance technician (Telephone Number) to investigate
for sources of CO from fuel burning equipment and
appliances, and inspect for proper operation of this
equipment. If problems are identified during this
inspection have the equipment serviced immediately.
Note any combustion equipment not inspected by the
technician and consult the manufacturers' instructions, or
contact the manufacturers directly, for more information
about CO safety and this equipment. Make sure that
motor vehicles are not, and have not been, operating in
an attached garage or adjacent to the residence.
The premises should be well ventilated when household cleaning supplies
or similar contaminants are used.
DETECTOR REPLACEMENT
This detector is manufactured with a long-life carbon monoxide sensor.
Over time the sensor will lose sensitivity, and will need to be replaced with
a new carbon monoxide detector. The detector’s lifespan is 5 years from the
date of manufacture.
NOTE: When the detector is removed from its base, a Tamper message is
sent to the central station.
The detector will also cause a trouble condition once it has reached the end
of its useful life. If this occurs, it is time to replace the detector.
NOTE: Before replacing the detector, notify the proper authorities that
maintenance is being performed and the system will be temporarily out
of service. Disable the zone or system undergoing maintenance to prevent
any unwanted alarms. Dispose of the detector in accordance with any local
regulations.
NOTE: The replacement date that appears on the device is the date beyond
which the device may no longer detect carbon monoxide accurately and
should be immediately replaced.
10
APD0602 A140513 Wireless CO Install
CAUTION
It should be noted the installation, operation, testing and maintenance of
the Wireless Carbon Monoxide Alarm is different than smoke detectors. Per
NFPA 720 section 5.3.7.2 the detector shall not be connected to a zone that
signals a re condition (i.e. smoke detectors zones). Therefore, the Wireless
Carbon Monoxide Alarm must be programmed as a non-re zone. See the
control’s Installation Instructions for the appropriate carbon monoxide
zone type to be programmed.
SPECIFICATIONS
Power Source: One 3-volt CR123A Panasonic Lithium Battery (included)
Audible Signal (temp 4 tone): 85 dBA min. in alarm (at 10ft (3m))
Operating Current: 10 µA
Temperature Range: 40°F (4.4°C) to 100°F (37.8°C)
Operating Humidity Range: 15% to 95% Relative Humidity, non-condensing
Pending Agency Listings: UL standard 2075, UL 2034 and CSA 6.19-01
51000-305
Détecteur de monoxyde de carbone sans l
Guide d'installation
Attention: Vous devez lire ce manuel avant d’utiliser l’appareil et le conserver pour
les références futures.
RENSEIGNEMENTS GÉNÉRAUX
Le détecteur de monoxyde de carbone sans l est un détecteur sans l alimenté par une
pile 3V conçue pour être utilisée avec des systèmes d'alarme sans l compatibles. Le
détecteur se compose d'un capteur électrochimique de monoxyde de carbone couplé
à un émetteur sans l. Le détecteur de monoxyde de carbone sans l communique
avec le panneau de commande et peut envoyer des messages concernant le statut de
l’alarme, du dispositif de sécurité et de la pile au récepteur du système. Reportez-vous
aux instructions du système sans l pour connaître le nombre maximum d’émetteurs
pouvant être utilisés avec ce système.
IMPORTANT: ce détecteur doit être testé et entretenu régulièrement selon la norme
NFPA 720.
Cet appareil a été conçu pour protéger les personnes des effets nocifs d’une exposition
au monoxyde de carbone. Il ne protégera pas complètement les personnes souffrant
de problèmes médicaux particuliers. En cas de doute, consultez votre médecin.
AVERTISSEMENT
Ce produit a été conçu pour un usage en intérieur dans des locaux résidentiels. Il
n'est pas conçu pour répondre aux normes commerciales ou industrielles dénies
par l'Occupational Safety and Health Administration (L'Agence pour la sécurité et la
santé au travail).
Contenu de la boîte:
• Détecteur de monoxyde de carbone sans l avec son socle
• Guide d'installation
• Paquet de vis et de pièces d'ancrage
• Étiquettes, le cas échéant
• 1 pile CR123A Panasonic
!
12
Installation du détecteur de CO sans l APD0602 A140513
Le détecteur de monoxyde de carbone sans l contient une sonde qui émet une
séquence temporelle à 4 tonalités ANSI S3.41 temporel 3 dans des conditions d’alarme
(voir Tableau 1 pour consulter la séquence temporelle). En état d'alerte, un message est
envoyé aussi au panneau de commande et l'ID du détecteur s'afche sur la console.
En cas de déclenchement d'une alarme, appuyez sur le bouton de silence pour arrêter
la sonde pendant cinq minutes. L'installation du socle de xation est simpliée grâce
à l'intégration de caractéristiques compatibles avec les attaches pour cloisons sèches
(non fournies) et d'autres méthodes.
La DEL tricolore (rouge, jaune, vert) et la sonde du détecteur émettent des signaux visuels
et sonores locaux relatifs au statut du détecteur tel que l'indique le Tableau 1.
Lors de la première mise sous tension, la DEL clignote alternativement entre le vert, le
jaune et le rouge. Il faut environ 60 seconds pour que le capteur de CO du détecteur
se stabilise.
À la n de la mise sous tension, si le détecteur fonctionne normalement, la DEL verte
clignote une fois toutes les 12 secondes.
État DEL
Sonde
(n'appuyez pas
simultanément sur la
sonde et la DEL)
Radio
signalisation
Normal
Clignotement vert
toutes les 12 secondes
Désactivé
Normal
(Aucun)
Alarme/Test
Clignote en rouge
toutes les
12 secondes
ANSI S3A1 temporel 4
(appuyez sur le bouton
pour mettre en silencieux
pendant 5 minutes)
Alarme
Détecteur
Défaut
Clignote en jaune
toutes les
6 secondes
Un bip sonore de
100ms toutes les
45 secondes
Panne
Pile faible
Clignote en jaune
toutes les
12 secondes
Un bip sonore de 100ms
toutes les 45 secondes
(appuyez sur le bouton
pour mettre en silencieux
pendant 12 heures)
Pile faible
Fin de vie
du détecteur
Clignote en jaune
toutes les
23 secondes
Un bip sonore de
100ms toutes les
45 secondes
Panne
Mise sous
tension
Clignote en vert, jaune
puis rouge toute les
12 secondes
Un bip sonore de 100ms
à la n de la séquence de
mise sous tension
Aucun
Languette de
sécurité
Clignote en vert, jaune
puis rouge toute les
12 secondes
Désactivé
Languette
de sécurité
Tableau 1. Statut et indications du détecteur
13
Installation du détecteur de CO sans l APD0602 A140513
État DEL
Sonde
(n'appuyez pas
simultanément sur la
sonde et la DEL)
Radio
signalisation
Normal
Clignotement vert
toutes les 12 secondes
Désactivé
Normal
(Aucun)
Alarme/Test
Clignote en rouge
toutes les
12 secondes
ANSI S3A1 temporel 4
(appuyez sur le bouton
pour mettre en silencieux
pendant 5 minutes)
Alarme
Détecteur
Défaut
Clignote en jaune
toutes les
6 secondes
Un bip sonore de
100ms toutes les
45 secondes
Panne
Pile faible
Clignote en jaune
toutes les
12 secondes
Un bip sonore de 100ms
toutes les 45 secondes
(appuyez sur le bouton
pour mettre en silencieux
pendant 12 heures)
Pile faible
Fin de vie
du détecteur
Clignote en jaune
toutes les
23 secondes
Un bip sonore de
100ms toutes les
45 secondes
Panne
Mise sous
tension
Clignote en vert, jaune
puis rouge toute les
12 secondes
Un bip sonore de 100ms
à la n de la séquence de
mise sous tension
Aucun
Languette de
sécurité
Clignote en vert, jaune
puis rouge toute les
12 secondes
Désactivé
Languette
de sécurité
Défaut du détecteur: Lorsque le contrôle du capteur est en panne, la DEL clignote
en jaune une fois toutes les six secondes et un bip sonore se déclenche toutes les
45 secondes. Au bout de 12 heures, le panneau de contrôle afche un message de
perte de contrôle.
Fin de vie du détecteur: Lorsque le détecteur est en n de vie, la DEL jaune clignote
une fois toutes les 23 secondes et un bip sonore se déclenche toutes les 45
secondes. Au bout de 12 heures, le panneau de contrôle afche un message de
perte de contrôle. Ceci indique que le capteur de CO est usagé et que vous devez
donc changer le détecteur. La durée de vie du détecteur est de cinq ans à partir de
la date de fabrication. Reportez-vous à la section CHANGEMENT DU DÉTECTEUR.
Détection d'un signal de pile faible: Le détecteur de monoxyde de carbone sans l
est alimenté par une pile Panasonic CR123A au lithium de 3 volts (incluse). Il vérie
régulièrement le niveau de la pile. Si une pile faible est détectée, l’émetteur envoie
un message de pile faible au panneau de commande qui afche l’identiant du
détecteur ayant un faible niveau de la pile. Par ailleurs, la DEL jaune du détecteur
va clignoter toutes les 12 secondes. La sonde du détecteur émet un bip sonore
toutes les 45 secondes (la DEL jaune continue à clignoter) jusqu’à ce que la pile
soit remplacée. Appuyer sur le bouton silence permet d'arrêter les signaux courts
pendant 12 heures, s'il n'existe aucun autre défaut. Remplacez la pile dès que les
bips sonores recommencent. Assurez-vous de remplacer l'ancienne pile par une
neuve.
Cet appareil est conforme à la partie 15 des règles de la FCC: Son fonctionnement
est soumis aux deux conditions suivantes : 1. Cet appareil ne doit pas provoquer
d’interférences nuisibles, et 2. Cet appareil doit accepter toute interférence reçue, y
compris les interférences qui peuvent causer un mauvais fonctionnement.
Des changements ou modications non autorisés pourraient entraîner l’annulation
de l’autorisation d’exploiter l’équipement.
INSTALLATION ET REMPLACEMENT DE LA PILE
Pour remplacer la pile:
1. Déposez le détecteur de son socle de xation en le tournant dans le sens
antihoraire. Enlevez la pile et mettez-la au rebut selon la réglementation locale.
2. An de garantir une mise hors tension appropriée, attendez 20 secondes au
moins avant d'installer la pile neuve.
3. lnstallez une pile Panasonic CR123A au lithium de 3 volts (disponible chez
votre revendeur Panasonic) dans le compartiment à piles. Suivez le schéma
de polarité présenté dans le compartiment. Si la pile est mal insérée, retirez-la
délicatement à l’aide d’un outil non conducteur et réinsérez-la correctement.
4. Réinstallez le détecteur sur le socle en le faisant tourner dans le sens horaire.
5. Après la mise sous tension, la DEL verte devrait clignoter une fois toutes les 12
secondes environ, pour indiquer un fonctionnement normal. Si la pile n’est
pas installée correctement, le détecteur ne fonctionnera pas et la pile risque
14
Installation du détecteur de CO sans l APD0602 A140513
Attention: This manual should be read prior to use
and retained for further information.
51000-305
Wireless Carbon Monoxide Alarm
Installation Guide
GENERAL INFORMATION
The Wireless Carbon Monoxide Alarm is a 3V battery powered wireless
detector intended for use with a compatible wireless alarm system.
The detector consists of an electrochemical carbon monoxide sensor assembly
coupled to a wireless transmitter. The Wireless Carbon Monoxide Alarm commu-
nicates with the control panel and can send alarm, tamper and battery condition
messages to the systems receiver. Refer to the wireless systems instruction for
the maximum number of transmitters that can be supported.
IMPORTANT: This detector must be tested and maintained regularly following
NFPA 720 requirements.
This device is designed to protect individuals from the acute effects of carbon
monoxide exposure. It will not fully safeguard individuals with speci c medical
conditions. If in doubt consult a medical practitioner.
WARNING
This product is intended for use in ordinary indoor residential areas. It is not
designed to measure compliance with Occupational Safety & Health
Administration (OSHA) commercial and industrial standards.
Contents of box:
- Wireless Carbon Monoxide Alarm with base
- Installation guide
- Pack of screws and xings
- Stickers as appropriate
- 1 CR123A Panasonic battery
The Wireless Carbon Monoxide Alarm contains a sounder which generates the ANSI
S3.41 temporal 4 pattern in an alarm condition (see Table 1 for temporal 4 pattern).
In alarm, a message is also sent to the control panel and the detectors ID is displayed at
t h e c o nso l e . D u r i n g a n a l a r m c o n di t i o n , p r e s si n g t h e d et e c t o r s h u s h b u t t o n w i l l s i l e n c e
the sounder for ve m i n ut e s . T h e m o u nt i n g b as e i n st a ll a t i o n i s s i m pli ed by the incorpo-
r a t i o n o f f e a t u r e s c o m p a t i b l e f o r b o t h d r y w a l l f a s t e n e r s ( n o t s u p p l i e d ) a n d o t h e r m e t h o d s .
Tricolored LED (green, yellow, red) and a sounder on the detector provide local
visual and audible indication of the detectors status as listed in Table 1.
During initial power-up the LED blinks alternately green, yellow then red.
It takes about 60 seconds for the detectors CO sensor to stabilize.
After power-up has completed and the detector is functioning normally, the green
LED blinks once every 12 seconds.
Table 1. Detector status and indication
Detector Trouble: When the sensor supervision is in trouble condition, the yellow
LED blinks once every six seconds and there is a chirp every 45 seconds. After
12 hours the panel will display a loss of supervision message.
Detector end of life feature: When the detector has reached the end of its life,
the yellow LED blinks once every 23 seconds and there is a chirp every
45 seconds. After 12 hours the panel will display a loss of supervision message.
This indicates that the CO sensor inside the detector has passed the end of its life
and the detector must be replaced. The detector lifespan is ve years from
the date of manufacture. Refer to DETECTOR REPLACEMENT section.
Low Battery Detection: The Wireless Carbon Monoxide Alarm is powered by
a single 3-volt CR123A Panasonic Lithium battery (included). The detector regu-
larly checks for a low battery. If a low battery is detected, the transmitter sends
a low battery message to the control panel, which displays the detectors ID at
low battery. In addition, the yellow LED of the detector will blink every 12 seconds.
The detectors sounder will chirp every 45 seconds (yellow LED continues to
blink) until the battery is replaced. Pressing the hush button will silence the chirps
for 12 hours, if no other trouble conditions exist. The battery should be replaced
WHEN the chirps begin. Be sure to replace the battery with a fresh one.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: 1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
Unauthorized changes or modi cations could void the users authority to operate
the equipment.
BATTERY INSTALLATION AND REPLACEMENT
To replace the battery:
1. Remove the detector from its mounting base by twisting the detector counter-
clockwise. Remove and dispose of the battery according to your local regulations.
2. To ensure proper power-down sequence, wait a minimum of 20 seconds before
installing new battery.
3. Install a new 3-volt CR123A Panasonic Lithium battery (available from your
Panasonic dealer) in the battery compartment. Follow the polarity diagram inside
the compartment. If the battery is incorrectly inserted please remove gently with a
non-conductive tool and correctly reinsert.
4. Reinstall the detector onto the mounting base by turning the detector clockwise.
5. After the power-up sequence the green LED should blink about once every
12 seconds to indicate normal operation. If the battery is not installed correctly, the
detector will not operate and the battery may be damaged. If the detector does not
power-up, check for correct battery installation and for a fully charged battery.
CONSTANT EXPOSURES TO HIGH OR LOW TEMPERATURES OR HIGH
HUMIDITY MAY REDUCE BATTERY LIFE.
COMPARTIMENT DE LA BATTERIE
Fig 1. Wireless Carbon Monoxide Alarm
PROGRAMMING
Refer to the appropiate compatible control panel programming guide for the proper
procedure required to enroll the wireless carbon monoxide alarm into the system.
MOUNTING THE DETECTOR
Note: These alarm devices should only be installed and commissioned by a com-
petent engineer/technician.
First, determine the best location for the detector, one that provides proper carbon
monoxide detection (see Figure 2 for suggested detection locations) .
Proper Carbon Monoxide Detection Location
Wall-mounted detectors should be positioned at least as high as a light switch,
and at least six inches (15cm) from the ceiling. In a ceiling location, the detector
should be at least 12 inches (30cm) from any wall.
Where to install, ideally:
- Within 10 feet (3m) of a sleeping area
- Inside the bedroom if it contains a fuel burning appliance
- On every oor of the building
- Ideally, install in any room that contains a fuel burning appliance
- If the appliance or the room is not normally used, such as the boiler room,
the detector should be placed just outside the room so the alarm can be heard
more easily
Where NOT to install, ideally:
- Directly above a sink, cooker, stove or oven
- Do not locate detector within 5 feet (1.5m) of any cooking appliance
- Next to a door or window that would be affected by drafts i.e. extractor fan or air
vent
- Outside
- Do not install in any environment that does not comply with the detectors environ-
mental speci cations
- In or below a cupboard
- Where air ow would be obstructed by curtains or furniture
- Where dirt or dust could collect and block the sensor
- Where it could be knocked, damaged, or inadvertently removed
Fig 2. Detector Location Diagram
Mounting Procedure
Once a suitable location is found, mount the detector as follows:
1. Refer to the diagram below and install the mounting base on the ceiling or on
the wall (if local ordinances permit) using screw locations as required. Use the two
screws and anchors provided. Maneuver the base so the screws are at the elbow
of the screw slots and secure.
2. Fit the detector inside the base by aligning it over the base as shown (detectors
alignment notch should be slightly offset from mounting base tamper release tab),
Status LEDs
Sounder
(does not pulse the
sounder
and LED concurrently)
Radio
signalling
Normal
Green ash every 12
seconds
Off
Normal
(None)
Alarm/
Test
Red ash every 12 seconds
ANSI S3.41 temporal 4
(press button to hush for 5
minutes)
Alarm
Detector
trouble
Yellow ash every 6
seconds
One 100ms chirp every 45
seconds
Fault
Low
battery
Yellow ash every 12
seconds
One 100ms chirp every 45
seconds (press button to
hush for 12 hours)
Low
Battery
Detector
end of
life
Yellow ash every 23
seconds
One 100ms chirp every 45
seconds
Fault
Power-
up
Green, yellow, red ash se-
quence every 12 seconds
One 100ms chirp at end of
power-up sequence
None
Tamper
Green, yellow, red ash se-
quence every 12 seconds
Off Tamper
CHAMBRE
CHAMBRE CHAMBRE
SALONCUISINE
CAVE
PORTES
FERMÉES
GARAGE
À CH
EMPLACEMENT DE L’ALARME DE MONOXYDE DE CARBONE POUR UN DOMICILE
À PLUSIEURS ÉTAGES
INST APD0602 A140513
Attention: This manual should be read prior to use
and retained for further information.
51000-305
Wireless Carbon Monoxide Alarm
Installation Guide
GENERAL INFORMATION
The Wireless Carbon Monoxide Alarm is a 3V battery powered wireless
detector intended for use with a compatible wireless alarm system.
The detector consists of an electrochemical carbon monoxide sensor assembly
coupled to a wireless transmitter. The Wireless Carbon Monoxide Alarm commu-
nicates with the control panel and can send alarm, tamper and battery condition
messages to the systems receiver. Refer to the wireless systems instruction for
the maximum number of transmitters that can be supported.
IMPORTANT: This detector must be tested and maintained regularly following
NFPA 720 requirements.
This device is designed to protect individuals from the acute effects of carbon
monoxide exposure. It will not fully safeguard individuals with speci c medical
conditions. If in doubt consult a medical practitioner.
WARNING
This product is intended for use in ordinary indoor residential areas. It is not
designed to measure compliance with Occupational Safety & Health
Administration (OSHA) commercial and industrial standards.
Contents of box:
- Wireless Carbon Monoxide Alarm with base
- Installation guide
- Pack of screws and xings
- Stickers as appropriate
- 1 CR123A Panasonic battery
The Wireless Carbon Monoxide Alarm contains a sounder which generates the ANSI
S3.41 temporal 4 pattern in an alarm condition (see Table 1 for temporal 4 pattern).
In alarm, a message is also sent to the control panel and the detectors ID is displayed at
t h e c o n s o l e. D u r i n g a n a l a r m c o n d i t i o n , p r e s s i n g t h e d e t e c t o r s h u s h b u t to n w i l l s i l en c e
the sounder for ve m i n ut e s . T h e m o u nt in g b a s e i n s t a l l at i o n i s s i m p l i ed by the incorpo-
r a t i o n o f f e a t u r e s c o m p a t i b l e f o r b o t h d r y w a l l f a s t e n e r s (n o t s u p p l i e d ) a n d o t h e r m e t h o d s .
Tricolored LED (green, yellow, red) and a sounder on the detector provide local
visual and audible indication of the detectors status as listed in Table 1.
During initial power-up the LED blinks alternately green, yellow then red.
It takes about 60 seconds for the detectors CO sensor to stabilize.
After power-up has completed and the detector is functioning normally, the green
LED blinks once every 12 seconds.
Table 1. Detector status and indication
Detector Trouble: When the sensor supervision is in trouble condition, the yellow
LED blinks once every six seconds and there is a chirp every 45 seconds. After
12 hours the panel will display a loss of supervision message.
Detector end of life feature: When the detector has reached the end of its life,
the yellow LED blinks once every 23 seconds and there is a chirp every
45 seconds. After 12 hours the panel will display a loss of supervision message.
This indicates that the CO sensor inside the detector has passed the end of its life
and the detector must be replaced. The detector lifespan is ve years from
the date of manufacture. Refer to DETECTOR REPLACEMENT section.
Low Battery Detection: The Wireless Carbon Monoxide Alarm is powered by
a single 3-volt CR123A Panasonic Lithium battery (included). The detector regu-
larly checks for a low battery. If a low battery is detected, the transmitter sends
a low battery message to the control panel, which displays the detectors ID at
low battery. In addition, the yellow LED of the detector will blink every 12 seconds.
The detectors sounder will chirp every 45 seconds (yellow LED continues to
blink) until the battery is replaced. Pressing the hush button will silence the chirps
for 12 hours, if no other trouble conditions exist. The battery should be replaced
WHEN the chirps begin. Be sure to replace the battery with a fresh one.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: 1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
Unauthorized changes or modi cations could void the users authority to operate
the equipment.
BATTERY INSTALLATION AND REPLACEMENT
To replace the battery:
1. Remove the detector from its mounting base by twisting the detector counter-
clockwise. Remove and dispose of the battery according to your local regulations.
2. To ensure proper power-down sequence, wait a minimum of 20 seconds before
installing new battery.
3. Install a new 3-volt CR123A Panasonic Lithium battery (available from your
Panasonic dealer) in the battery compartment. Follow the polarity diagram inside
the compartment. If the battery is incorrectly inserted please remove gently with a
non-conductive tool and correctly reinsert.
4. Reinstall the detector onto the mounting base by turning the detector clockwise.
5. After the power-up sequence the green LED should blink about once every
12 seconds to indicate normal operation. If the battery is not installed correctly, the
detector will not operate and the battery may be damaged. If the detector does not
power-up, check for correct battery installation and for a fully charged battery.
CONSTANT EXPOSURES TO HIGH OR LOW TEMPERATURES OR HIGH
HUMIDITY MAY REDUCE BATTERY LIFE.
COMPARTIMENT DE LA BATTERIE
Fig 1. Wireless Carbon Monoxide Alarm
PROGRAMMING
Refer to the appropiate compatible control panel programming guide for the proper
procedure required to enroll the wireless carbon monoxide alarm into the system.
MOUNTING THE DETECTOR
Note: These alarm devices should only be installed and commissioned by a com-
petent engineer/technician.
First, determine the best location for the detector, one that provides proper carbon
monoxide detection (see Figure 2 for suggested detection locations) .
Proper Carbon Monoxide Detection Location
Wall-mounted detectors should be positioned at least as high as a light switch,
and at least six inches (15cm) from the ceiling. In a ceiling location, the detector
should be at least 12 inches (30cm) from any wall.
Where to install, ideally:
- Within 10 feet (3m) of a sleeping area
- Inside the bedroom if it contains a fuel burning appliance
- On every oor of the building
- Ideally, install in any room that contains a fuel burning appliance
- If the appliance or the room is not normally used, such as the boiler room,
the detector should be placed just outside the room so the alarm can be heard
more easily
Where NOT to install, ideally:
- Directly above a sink, cooker, stove or oven
- Do not locate detector within 5 feet (1.5m) of any cooking appliance
- Next to a door or window that would be affected by drafts i.e. extractor fan or air
vent
- Outside
- Do not install in any environment that does not comply with the detectors environ-
mental speci cations
- In or below a cupboard
- Where air ow would be obstructed by curtains or furniture
- Where dirt or dust could collect and block the sensor
- Where it could be knocked, damaged, or inadvertently removed
Fig 2. Detector Location Diagram
Mounting Procedure
Once a suitable location is found, mount the detector as follows:
1. Refer to the diagram below and install the mounting base on the ceiling or on
the wall (if local ordinances permit) using screw locations as required. Use the two
screws and anchors provided. Maneuver the base so the screws are at the elbow
of the screw slots and secure.
2. Fit the detector inside the base by aligning it over the base as shown (detectors
alignment notch should be slightly offset from mounting base tamper release tab),
Status LEDs
Sounder
(does not pulse the
sounder
and LED concurrently)
Radio
signalling
Normal
Green ash every 12
seconds
Off
Normal
(None)
Alarm/
Test
Red ash every 12 seconds
ANSI S3.41 temporal 4
(press button to hush for 5
minutes)
Alarm
Detector
trouble
Yellow ash every 6
seconds
One 100ms chirp every 45
seconds
Fault
Low
battery
Yellow ash every 12
seconds
One 100ms chirp every 45
seconds (press button to
hush for 12 hours)
Low
Battery
Detector
end of
life
Yellow ash every 23
seconds
One 100ms chirp every 45
seconds
Fault
Power-
up
Green, yellow, red ash se-
quence every 12 seconds
One 100ms chirp at end of
power-up sequence
None
Tamper
Green, yellow, red ash se-
quence every 12 seconds
Off Tamper
CHAMBRE
CHAMBRE CHAMBRE
SALONCUISINE
CAVE
PORTES
FERMÉES
GARAGE
À CH
EMPLACEMENT DE L’ALARME DE MONOXYDE DE CARBONE POUR UN DOMICILE
À PLUSIEURS ÉTAGES
INST APD0602 A140513
Fig 1. Détecteur de monoxyde de carbone sans l
d’être endommagée. Si le détecteur ne démarre pas, vériez que vous avez
respecté la polarité de la pile et que celle-ci est bien chargée.
DES EXPOSITIONS CONSTANTES À DES TEMPÉRATURES ÉLEVÉES OU BASSES OU À
UNE HUMIDITÉ ÉLEVÉE PEUVENT RÉDUIRE LA DURÉE DE VIE DES PILES.
PROGRAMMATION
Reportez-vous au guide de programmation du panneau de commande compatible
pour la procédure appropriée nécessaire pour enregistrer le détecteur de monoxyde de
carbone sans l dans le système.
MONTAGE DU DÉTECTEUR
Remarque : Ces dispositifs d’alarme doivent être installés et mis en service par un
ingénieur/technicien compétent.
Commencez par déterminer le meilleur emplacement pour le détecteur, c.-à-d. un lieu
permettant de détecter au mieux le monoxyde de carbone (Voir Figure 2 pour consulter
les emplacements recommandés).
Emplacements permettant une meilleure détection du monoxyde de carbone
Les détecteurs muraux doivent être positionnés au moins à la même hauteur qu’un
interrupteur et à au moins 15cm (6po) du plafond. Si le détecteur est installé au plafond,
ce dernier doit être placé à au moins 30cm (12po) de chaque mur.
Dans l'idéal, installez-le:
• À 3m (10 pieds) d’une chambre à coucher
• Dans une chambre qui contient un appareil à foyer
• À chaque étage d'un bâtiment
• Si possible, installez-en un dans chaque chambre équipée d’un appareil à foyer
• Si l'appareil ou la pièce n’est pas utilisée régulièrement, à l'instar d'une chaufferie,
placez le détecteur juste à l’extérieur de la pièce pour que l’alarme puisse être
entendue plus facilement
15
Installation du détecteur de CO sans l APD0602 A140513
Procédure d'installation
Une fois que vous avez trouvé un emplacement convenable, montez le détecteur
comme suit:
1. Consultez le schéma ci-dessous et installez le socle de xation au plafond ou sur
le mur (si les décrets locaux le permettent) à l’aide des positions de vis indiquées.
Utilisez les deux vis et les pièces d'ancrage fournies. Manipulez le socle pour que les
vis s’emboîtent correctement dans les fentes prévues à cet effet.
2. Ajustez le détecteur dans la base en l’alignant sur la base comme l'indique
l'illustration (l’encoche d’alignement du détecteur devrait être légèrement décalée
de la languette de sécurité du socle), puis tournez le détecteur dans le sens horaire
jusqu’à ce qu’il s'emboîte dans un déclic.
Attention: This manual should be read prior to use
and retained for further information.
51000-305
Wireless Carbon Monoxide Alarm
Installation Guide
GENERAL INFORMATION
The Wireless Carbon Monoxide Alarm is a 3V battery powered wireless
detector intended for use with a compatible wireless alarm system.
The detector consists of an electrochemical carbon monoxide sensor assembly
coupled to a wireless transmitter. The Wireless Carbon Monoxide Alarm commu-
nicates with the control panel and can send alarm, tamper and battery condition
messages to the systems receiver. Refer to the wireless systems instruction for
the maximum number of transmitters that can be supported.
IMPORTANT: This detector must be tested and maintained regularly following
NFPA 720 requirements.
This device is designed to protect individuals from the acute effects of carbon
monoxide exposure. It will not fully safeguard individuals with speci c medical
conditions. If in doubt consult a medical practitioner.
WARNING
This product is intended for use in ordinary indoor residential areas. It is not
designed to measure compliance with Occupational Safety & Health
Administration (OSHA) commercial and industrial standards.
Contents of box:
- Wireless Carbon Monoxide Alarm with base
- Installation guide
- Pack of screws and xings
- Stickers as appropriate
- 1 CR123A Panasonic battery
The Wireless Carbon Monoxide Alarm contains a sounder which generates the ANSI
S3.41 temporal 4 pattern in an alarm condition (see Table 1 for temporal 4 pattern).
In alarm, a message is also sent to the control panel and the detectors ID is displayed at
t h e c o n s o l e . D u r in g a n a l a r m c o n d i t i o n, p r e s s i n g t h e d e t e c t o r s h u s h b u t to n w i l l s i l e n c e
the sounder for ve m i nu t e s . T h e m o u n t i n g b as e i ns t a l l a t i o n i s s i m p l i ed by the incorpo-
r a t i o n o f f e a t u r e s c o m p a t i b l e f o r b o t h d r y w a l l f a s t e n e r s (n o t s u p p l i e d ) a n d o t h e r m e t h o d s .
Tricolored LED (green, yellow, red) and a sounder on the detector provide local
visual and audible indication of the detectors status as listed in Table 1.
During initial power-up the LED blinks alternately green, yellow then red.
It takes about 60 seconds for the detectors CO sensor to stabilize.
After power-up has completed and the detector is functioning normally, the green
LED blinks once every 12 seconds.
Table 1. Detector status and indication
Detector Trouble: When the sensor supervision is in trouble condition, the yellow
LED blinks once every six seconds and there is a chirp every 45 seconds. After
12 hours the panel will display a loss of supervision message.
Detector end of life feature: When the detector has reached the end of its life,
the yellow LED blinks once every 23 seconds and there is a chirp every
45 seconds. After 12 hours the panel will display a loss of supervision message.
This indicates that the CO sensor inside the detector has passed the end of its life
and the detector must be replaced. The detector lifespan is ve years from
the date of manufacture. Refer to DETECTOR REPLACEMENT section.
Low Battery Detection: The Wireless Carbon Monoxide Alarm is powered by
a single 3-volt CR123A Panasonic Lithium battery (included). The detector regu-
larly checks for a low battery. If a low battery is detected, the transmitter sends
a low battery message to the control panel, which displays the detectors ID at
low battery. In addition, the yellow LED of the detector will blink every 12 seconds.
The detectors sounder will chirp every 45 seconds (yellow LED continues to
blink) until the battery is replaced. Pressing the hush button will silence the chirps
for 12 hours, if no other trouble conditions exist. The battery should be replaced
WHEN the chirps begin. Be sure to replace the battery with a fresh one.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: 1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
Unauthorized changes or modi cations could void the users authority to operate
the equipment.
BATTERY INSTALLATION AND REPLACEMENT
To replace the battery:
1. Remove the detector from its mounting base by twisting the detector counter-
clockwise. Remove and dispose of the battery according to your local regulations.
2. To ensure proper power-down sequence, wait a minimum of 20 seconds before
installing new battery.
3. Install a new 3-volt CR123A Panasonic Lithium battery (available from your
Panasonic dealer) in the battery compartment. Follow the polarity diagram inside
the compartment. If the battery is incorrectly inserted please remove gently with a
non-conductive tool and correctly reinsert.
4. Reinstall the detector onto the mounting base by turning the detector clockwise.
5. After the power-up sequence the green LED should blink about once every
12 seconds to indicate normal operation. If the battery is not installed correctly, the
detector will not operate and the battery may be damaged. If the detector does not
power-up, check for correct battery installation and for a fully charged battery.
CONSTANT EXPOSURES TO HIGH OR LOW TEMPERATURES OR HIGH
HUMIDITY MAY REDUCE BATTERY LIFE.
COMPARTIMENT DE LA BATTERIE
Fig 1. Wireless Carbon Monoxide Alarm
PROGRAMMING
Refer to the appropiate compatible control panel programming guide for the proper
procedure required to enroll the wireless carbon monoxide alarm into the system.
MOUNTING THE DETECTOR
Note: These alarm devices should only be installed and commissioned by a com-
petent engineer/technician.
First, determine the best location for the detector, one that provides proper carbon
monoxide detection (see Figure 2 for suggested detection locations) .
Proper Carbon Monoxide Detection Location
Wall-mounted detectors should be positioned at least as high as a light switch,
and at least six inches (15cm) from the ceiling. In a ceiling location, the detector
should be at least 12 inches (30cm) from any wall.
Where to install, ideally:
- Within 10 feet (3m) of a sleeping area
- Inside the bedroom if it contains a fuel burning appliance
- On every oor of the building
- Ideally, install in any room that contains a fuel burning appliance
- If the appliance or the room is not normally used, such as the boiler room,
the detector should be placed just outside the room so the alarm can be heard
more easily
Where NOT to install, ideally:
- Directly above a sink, cooker, stove or oven
- Do not locate detector within 5 feet (1.5m) of any cooking appliance
- Next to a door or window that would be affected by drafts i.e. extractor fan or air
vent
- Outside
- Do not install in any environment that does not comply with the detectors environ-
mental speci cations
- In or below a cupboard
- Where air ow would be obstructed by curtains or furniture
- Where dirt or dust could collect and block the sensor
- Where it could be knocked, damaged, or inadvertently removed
Fig 2. Detector Location Diagram
Mounting Procedure
Once a suitable location is found, mount the detector as follows:
1. Refer to the diagram below and install the mounting base on the ceiling or on
the wall (if local ordinances permit) using screw locations as required. Use the two
screws and anchors provided. Maneuver the base so the screws are at the elbow
of the screw slots and secure.
2. Fit the detector inside the base by aligning it over the base as shown (detectors
alignment notch should be slightly offset from mounting base tamper release tab),
Status LEDs
Sounder
(does not pulse the
sounder
and LED concurrently)
Radio
signalling
Normal
Green ash every 12
seconds
Off
Normal
(None)
Alarm/
Test
Red ash every 12 seconds
ANSI S3.41 temporal 4
(press button to hush for 5
minutes)
Alarm
Detector
trouble
Yellow ash every 6
seconds
One 100ms chirp every 45
seconds
Fault
Low
battery
Yellow ash every 12
seconds
One 100ms chirp every 45
seconds (press button to
hush for 12 hours)
Low
Battery
Detector
end of
life
Yellow ash every 23
seconds
One 100ms chirp every 45
seconds
Fault
Power-
up
Green, yellow, red ash se-
quence every 12 seconds
One 100ms chirp at end of
power-up sequence
None
Tamper
Green, yellow, red ash se-
quence every 12 seconds
Off Tamper
CHAMBRE
CHAMBRE CHAMBRE
SALONCUISINE
CAVE
PORTES
FERMÉES
GARAGE
À CH
EMPLACEMENT DE L’ALARME DE MONOXYDE DE CARBONE POUR UN DOMICILE
À PLUSIEURS ÉTAGES
INST APD0602 A140513
Fig 2. Schéma de l'emplacement du détecteur
Si possible, ne PAS installer l’alarme :
• Directement au-dessus d'un évier, d'une cuisinière, d'un poêle ou d'un four
• Ne placez pas le détecteur à 1,5m (5pi) d’un appareil de cuisson
• À proximité d’une porte ou d’une fenêtre où il peut y avoir des courants d’air (par ex.
un ventilateur d'extraction ou une bouche d’aération)
• À l'extérieur
• Ne l'installez pas dans un environnement qui n'est pas conforme aux spécications
environnementales du détecteur
• Dans ou sous un placard
• Dans des endroits où la circulation d'air serait obstruée par des rideaux ou
des meubles
• Dans un endroit où de la saleté ou de la poussière pourrait s'accumuler et bloquer
le détecteur
• Dans un endroit où il pourrait être cogné, endommagé ou ôté par inadvertance.
16
Installation du détecteur de CO sans l APD0602 A140513
3. Testez le détecteur à la n de l’installation (comme le décrit la section TESTER LE
DÉTECTEUR de ce manuel) et consultez les instructions du système de commande
pour plus de renseignements sur l’utilisation des appareils sans l.
NE FIXEZ PAS le détecteur sur des panneaux amovibles au plafond.
REMARQUE: La boîte du détecteur contient deux autocollants d’avertissement. Collez-
en un à proximité du détecteur de monoxyde de carbone et un autre près d’une source
d’air frais où les occupants du domicile se rassembleront en cas de déclenchement
de l’alarme.
then turn the detector in a clockwise direction until it clicks into place.
3. Test the detector after completing the installation (as described in the TESTING
THE DETECTOR section of this manual) and refer to the control systems instruc-
tions for additional information concerning the use of wireless devices.
DO NOT attach the detector to removable ceiling panels.
NOTE: Two warning labels are provided in the detector box. Please stick one
next to the CO detector and another near to a source of fresh air where members
of the household will gather if alarm signal sounds.
Fig 3. Installation du détecteur
CAUTION
Airborne dust particles can enter the detector. Apollo recommends the removal
of detectors before beginning construction or any other dust producing activity.
Carbon monoxide detectors are not to be used with detector guards unless the
combination has been evaluated and found suitable for that purpose.
Tamper Protection
This detector has a built-in tamper switch that will cause a Tamper signal to be
displayed at the console of the alarm system if it is removed from its mounting
base.
The Wireless Carbon Monoxide Alarm includes a tamper resistant feature that
prevents removal from the mounting base without the use of a tool. To engage
the tamper resistant feature, cut the small plastic tab located on the mounting
base and then install the detector. To remove the detector from the base once
it has been made tamper resistant, use appropriate screwdriver to depress
the square tamper release tab located on the skirt of the mounting base
and turn the detector counterclockwise.
TESTING THE DETECTOR
NOTE: Before testing, notify the central station that the detector system is under-
going maintenance in order to prevent unwanted alarms. Testing the detector will
activate an alarm and send a signal to the panel. Also, the test function cannot be
used if the detector has a trouble or end-of-life condition.
Detectors must be tested after installation and following periodic maintenance.
Testing Detector Operation
This test checks the detectors sounder, LEDs, and transmitter.
1. The test button is located on the detector housing.
2. Push and hold the test button for a minimum of 5 seconds. The alarm panel
will trigger and then the detector will go into alarm. The sounder begins the
temporal 4 pattern and the red LED blinks. The alarm panels keypad should
display the detectors name in alarm.
CAUTION: Carbon Monoxide Gas and its Detection
This carbon monoxide detector is designed for indoor use only. Do not expose
to rain or moisture. Do not knock or drop the detector. Do not open or tamper with
the detector as this could cause malfunction. The detector will not protect against
the risk of carbon monoxide poisoning if not properly installed.
CAUTION: This device will only indicate the presence of carbon monoxide gas
at the sensor. Carbon monoxide gas may be present in other areas.
This carbon monoxide alarming device is designed to detect carbon monoxide
gas from ANY source of combustion. It is NOT designed to detect smoke, re
or other gases unless the product has been investigated and determined to
comply with applicable requirements.
This device should not be installed as a substitute for proper installation, use,
and maintenance of fuel burning appliances, including appropriate ventilation
and exhaust systems.
Carbon monoxide gas is a highly poisonous gas which is released when fuels
are burned. It is invisible, has no smell and is therefore impossible to detect with
the human senses. Under normal conditions in a room where fuel burning appli-
ances are well maintained and correctly ventilated, the amount of carbon monox-
ide released into the room by appliances should not be dangerous.
Conditions that can result in transient CO situations:
1. Excessive spillage or reverse venting of fuel-burning appliances caused by
- outdoor ambient conditions, such as wind direction and/or velocity,
including high gusts of wind, and insuf cient draft in the vent pipes,
- negative pressure differential resulting from the use of exhaust fans,
- simultaneous operation of several fuel-burning appliances competing
f for limited internal air,
- loose vent pipe connections from fuel- red appliances,
- obstructions, or unconventional vent pipe designs that can amplify
the above situations,
- poorly designed or maintained chimneys and/or vents,
2. Extended operation of unvented fuel-burning devices (range, oven,
replace, etc),
3. Temperature inversions that can trap exhaust gases near the ground,
4. Car idling in an open or closed attached garage, or near a home.
The following symptoms may be related to CARBON MONOXIDE POISONING
and should be discussed with ALL members of the household:
- Mild exposure: Headache, running nose, sore eyes, often described as  u - l i k e
symptoms
- Medium exposure: Dizziness, drowsiness, vomiting
- Extreme exposure: Unconsciousness, brain damage, death
Many causes of reported CARBON MONOXIDE POISONING indicate that while
victims are aware they are not well, they become so disoriented that they are
unable to save themselves by either exiting the building or calling for assistance.
Also, young children and pets may be the rst to be affected.
WARNING: IMPORTANT INFORMATION FOR THE USER
Individuals with medical problems may consider using warning devices which
provide audible and visual signals for carbon monoxide concentrations under
30 ppm.
WARNING
Actuation of this device indicates the presence of carbon monoxide (CO) which
can KILL YOU.
If alarm signal sounds, four beeps:
1. Operate hush/test button.
2. Immediately move to fresh air  outdoors or by an open window.
3. Check all persons are accounted for.
4. Do not re-enter the premises or move away from the open door/window until
the emergency services responders have arrived, the premises have been aired
out, and your alarm remains in its normal condition.
5. Call your emergency local service, re department or 911
6. If service signal sounds, one chirp, then check the service section to try and
correct.
7. After following steps 1-6, if your alarm reactivates within a 24 hour period,
repeat steps 1-6 and call your local quali ed technician to investigate for sources
of CO from fuel burning equipment and appliances and inspect for proper opera-
tion of this equipment. If problems are identi ed during this inspection, have the
equipment serviced immediately. Note any combustion equipment not inspected
by the technician and consult the manufacturers instructions, or contact the
manufacturers directly for more information about CO safety and this equip-
ment. Make sure that motor vehicles are not, and have not been, operating in an
attached garage or adjacent to the residence.
The premises should be well ventilated when household cleaning supplies or
similar contaminants are used.
DETECTOR REPLACEMENT
This detector is manufactured with a long-life carbon monoxide sensor. Over time
the sensor will lose sensitivity, and will need to be replaced with a new carbon
monoxide detector. The detectors lifespan is 5 years from the date of
manufacture.
NOTE: When the detector is removed from its base, a Tamper message is sent to
the central station.
The detector will also cause a trouble condition once it has reached the end of its
useful life. If this occurs, it is time to replace the detector.
NOTE: Before replacing the detector, notify the proper authorities that main-
tenance is being performed and the system will be temporarily out of service.
Disable the zone or system undergoing maintenance to prevent any unwanted
alarms. Dispose of the detector in accordance with any local regulations.
NOTE: The replacement date that appears on the device is the date beyond
which the device may no longer detect carbon monoxide accurately and should
be immediately replaced.
CAUTION
It should be noted the installation, operation, testing and maintenance of the
Wireless Carbon Monoxide Alarm is different than smoke detectors. Per NFPA
720 section 5.3.7.2 the detector shall not be connected to a zone that signals
a re condition (i.e. smoke detectors zones). Therefore, the Wireless Carbon
Monoxide Alarm must be programmed as a non- re zone. See the controls
Installation Instructions for the appropriate carbon monoxide zone type to be
programmed.
SPECIFICATIONS
Power Source: One 3-volt CR123A Panasonic Lithium Battery (included)
Audible Signal (temp 4 tone): 85 dBA min. in alarm (at 10ft (3m))
Operating Current: 10 A
Temperature Range: 40°F (4.4°C) to 100°F (37.8 °C)
Operating Humidity Range: 15% to 95% Relative Humidity, non-condensing
Pending Agency Listings: UL standard 2075, UL 2034 and CSA 6.19-01
Apollo America, Inc.
25 Corporate Drive
Auburn Hills, MI 48326
(248) 332-3900 Phone/Tech
support
www.apollo-fire.com
ATTENTION
Des particules de poussière peuvent pénétrer dans le détecteur. Apollo
recommande le retrait des détecteurs avant de commencer la construction ou
toute autre activité produisant de la poussière. Les détecteurs de monoxyde de
carbone ne doivent pas être utilisés avec des grilles de protection à moins que
la combinaison ait été évaluée et jugée appropriée à cet effet.
Languette de sécurité
Ce détecteur a été conçu avec une languette de sécurité qui afche le signal de
sécurité sur la console du système d’alarme en cas de retrait du détecteur de
son socle.
Ce détecteur de monoxyde de carbone sans l est équipé d’un système
d’inviolabilité empêchant de le retirer de son socle sans l’utilisation d’un outil.
Pour activer cette sécurité, coupez la petite languette en plastique située sur
le socle et installez le détecteur. Pour retirer le détecteur de son socle une
fois la sécurité mise en place, utilisez un tournevis adéquat pour appuyer sur
17
Installation du détecteur de CO sans l APD0602 A140513
la languette de sécurité carrée située sur le bord du socle; puis tournez le
détecteur dans le sens antihoraire.
TESTER LE DÉTECTEUR
REMARQUE : Avant le test, informez le poste central que le système du
détecteur est en maintenance an d’empêcher des alarmes superues. Le test
du détecteur active une alarme et envoie un signal au panneau. Par ailleurs, la
fonction de test ne peut pas être utilisée si le détecteur est en panne ou en n
de vie.
Les détecteurs doivent être testés après installation et en fonction de l’entretien
périodique.
Tester le fonctionnement du détecteur
Ce test vérie la sonde du détecteur, les DEL et l’émetteur.
1. Le bouton de test est situé sur le boîtier du détecteur.
2. Appuyez et maintenez le bouton de test pendant au moins 5 secondes.
Le panneau d’alarme se déclenche puis le détecteur se met en alerte. La
sonde émet la séquence temporelle 4 et la DEL rouge clignote. Les touches
du panneau d’alarme doivent en principe afcher le nom du détecteur
ayant déclenché l'alarme
ATTENTION: Le monoxyde de carbone et sa détection
Ce détecteur de monoxyde de carbone a été conçu pour être utilisé à l’intérieur
uniquement. Ne le placez pas dans un lieu exposé à la pluie ou à l’humidité.
Évitez tout choc avec le détecteur ou de le faire tomber. N'ouvrez ni ne forcez
le détecteur car cela risquerait d’entrainer un mauvais fonctionnement. Le
détecteur ne protège pas contre les intoxications au monoxyde de carbone si
celui-ci n’a pas été installé correctement.
ATTENTION: Cet appareil indique la présence de monoxyde de carbone sur le
capteur uniquement. Le monoxyde de carbone peut être présent ailleurs.
Cette alarme de détection de monoxyde de carbone a été conçue pour détecter
ce gaz QUELLE QUE SOIT la source de combustion. Elle n’a PAS été conçue
pour détecter la fumée, les incendies ou tout autre gaz, sauf si ce produit a été
testé et jugé conforme aux normes applicables.
Cet appareil ne doit pas être installé comme substitut de toute installation,
utilisation ou entretien correct d’un appareil à foyer, y compris tout système de
ventilation et d’échappement adéquat.
Le monoxyde de carbone est un gaz extrêmement toxique provenant de la
combustion de carburants. Il est invisible et inodore, donc impossible à détecter
par des moyens humains. Dans des conditions normales, une pièce équipée
d’un appareil à foyer correctement entretenu et bien ventilé, la quantité de
monoxyde de carbone dégagée ne devrait pas être dangereuse.
18
Installation du détecteur de CO sans l APD0602 A140513
Conditions pouvant entraîner la présence de monoxyde de carbone transitoire:
1. Production excessive ou ventilation inversée des appareils à foyer provenant de
• conditions climatiques extérieures, telles que la direction ou la vitesse du
vent, des rafales importantes ou des courants d’air insufsants dans les
tuyaux de ventilation,
• la différence de pression négative due à l’utilisation d’un ventilateur
d'évacuation,
• l'utilisation simultanée de plusieurs appareils à foyer dans un lieu
trop conné,
• du mauvais branchement des tuyaux de ventilation d’appareils à foyer,
• blocages ou d’une installation non conventionnelle des tuyaux de
ventilation pouvant aggraver les conditions ci-dessus,
• cheminées ou systèmes de ventilation mal conçus ou mal entretenus.
2. L'utilisation prolongée d’appareils à foyer mais non ventilés (cuisinière,
four, cheminée, etc.),
3. Température inversée pouvant piéger les gaz d’échappement au sol,
4. Moteur d’un véhicule à l’arrêt tournant au ralenti et conné dans un garage
ouvert ou fermé à l’intérieur ou à proximité du domicile.
Les symptômes suivants sont liés à l'INTOXICATION AU MONOXYDE DE
CARBONE et doivent être avec tous les membres de la famille;
1. Exposition légère : Légers maux de tête, nausées, vomissements, fatigue
(souvent décrit comme «symptômes grippaux»).
2. Exposition moyenne: Céphalées pulsatiles graves, somnolence, confusion,
rythme cardiaque rapide.
3. Exposition extrême: Perte de conscience, convulsions, insufsance cardio-
respiratoire, mort.
4. De nombreux cas signalés d'INTOXICATION AU MONOXYDE DE CARBONE
indiquent que même si les victimes sont conscientes qu'elles ne vont pas
bien, elles deviennent tellement désorientées qu'elles sont incapables de
se sauver et de quitter les lieux ou d'appeler à l'aide. Les jeunes enfants et
les animaux domestiques sont généralement les premiers touchés.
AVERTISSEMENT: RENSEIGNEMENTS IMPORTANTS POUR L'UTILISATEUR
Les personnes ayant des problèmes médicaux peuvent utiliser des dispositifs
d'alarme émettant des signaux sonores et visuels pour des concentrations en
monoxyde de carbone inférieures à 30ppm.
AVERTISSEMENT
Le déclenchement de votre avertisseur de CO indique la présence de monoxyde
de carbone (CO) qui PEUT VOUS TUER. Si le signal d'alarme retentit:
1. Appuyez sur le bouton réinitialiser/silence.
2. Appelez vos services d'urgence (Numéro de téléphone)
(département d'incendie ou 911).
!
!
19
Installation du détecteur de CO sans l APD0602 A140513
3. Déplacez-vous immédiatement vers une source d'air frais,
à l'extérieur ou près d'une porte ouverte / fenêtre. Faites le
décompte des personnes présentes pour vérifier que tout le
monde est pris en compte. Ne rentrez pas dans les locaux
ou ne vous éloignez pas de la porte/fenêtre ouverte jusqu'à
l'arrivée des agents des services d'urgence, l'aération des
locaux et le retour à la normale de votre avertisseur.
4. Une fois que vous avez suivi les étapes 1 à 3, si votre alarme
se réactive dans un délai de 24 heures, répétez les étapes 1 à 3
et appelez un technicien qualifié (numéro de téléphone) pour
enquêter sur les sources de CO des équipements et appareils
à foyer et vérifier le bon fonctionnement de cet équipement.
Si des problèmes sont identifiés au cours de cette inspection,
faites réparer l'équipement immédiatement. Notez tout appareil
à combustion non contrôlé par le technicien et consultez
les instructions du fabricant, ou contactez les fabricants
directement, pour plus de renseignements sur la sécurité du
CO et de cet équipement. Assurez-vous que les véhicules à
moteur ne sont pas ou n'ont pas été en fonctionnement dans
un garage attenant ou à proximité de la résidence.
Ventilez votre habitation lorsque vous utilisez des produits d’entretien et autres
produits chimiques.
REMPLACEMENT DU DÉTECTEUR
Ce détecteur est doté d’un capteur de monoxyde de carbone durable.
Cependant au l du temps, le capteur perd de son acuité et vous devrez changer
le détecteur de monoxyde de carbone. La durée de vie du détecteur est de 5 ans
à compter de la date de fabrication.
REMARQUE: Lorsque vous retirez le détecteur de son socle, un message d’alerte
est envoyé au poste central.
Le détecteur se mettra également en mode panne une fois usagé. Si cela se
produit, il est temps de changer le détecteur.
REMARQUE : Avant de changer le détecteur, veuillez informer les autorités
compétentes que celui-ci est en cours de maintenance et que le système sera
momentanément hors service. Désactivez la zone ou le système en cours de
maintenance an d’éviter toute alarme non désirée. Mettez le détecteur au
rebut conformément à la réglementation locale.
REMARQUE: La date de remplacement gurant sur l’appareil est la date à partir
de laquelle l’appareil risque de ne plus détecter correctement le monoxyde de
carbone et à laquelle il doit donc être changé.
20
Installation du détecteur de CO sans l APD0602 A140513
ATTENTION
Veuillez noter que l’installation, le fonctionnement, le test et l’entretien de
ce détecteur de monoxyde de carbone sans l sont différents de ceux des
détecteurs de fumée. Selon la section 5.3.7.2 de la norme NFPA 720, le détecteur
ne doit pas être connecté à une zone pouvant émettre des signaux concernant
un incendie (ex. des zones équipées de détecteurs de fumée). Ce détecteur de
monoxyde de carbone sans l doit donc être programmé en tant que zone sans
détection d’incendie. Reportez-vous aux instructions d’installation du contrôle
pour connaître le type de zone devant être programmé pour le monoxyde
de carbone.
SPÉCIFICATIONS
Source d’alimentation: 1 pile 3volts CR123A Panasonic au lithium (incluse)
Signal sonore (tonalité temp 4): 85dBA min. en alarme (à 10 pieds (3m))
Courant de fonctionnement: 10µA
Plage de température: 4,4°C (40°F) à 37,8°C (100°F)
Plage d'humidité en fonctionnement : 15 % à 95 % d’humidité relative, sans
condensation
En attente d'homologations: Normes UL 2075, UL 2034 et CSA 6.19-01
Apollo America
25 Corporate Drive
Auburn Hills, MI 48326
248-332-3900 Phone
888-332-2241 Tech Support
www.apollo-re.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Apollo 51000-305 Guide d'installation

Catégorie
Détecteurs de monoxyde de carbone (CO)
Taper
Guide d'installation

dans d''autres langues