Emac NLX1638NP Guide d'installation

Taper
Guide d'installation
R03.001_11/01/2012
TECHNICAL FILE
Novosuelo/Novopared
Stainless steel
General Features
Material: Stainless steel AISI 304
Length: 8ft2in / 2,5 m.l.
Dimensions (h): 5/16”, 3/8”, 1/2”, 9/16”
8, 10, 12, 15
Packaging: 30 u./box
Finishes: High brightness
Applications
Novosuelo/Novopared Stainless steel is a prole designed to protect edges of ceramic installations.
It can also be installed as a ooring separator or countertop nish among others.
Technical Features and tests
Page 1 of 3
Materials
Alloy
AISI-304
Test of chemical composition of each
batch
AIMME
Corrosion resistance
Salt spray test
+ 504 hours without variation
+ 650 hours without variation (models
made of stainless steel covered with
titanium)
UNE 112017:92
AIMME
Stainless Steel
Novosuelo/Novopared stainless steel is a prole made of stainless steel AISI-304. All material batches
are tested with the chemical composition test to determine that they fulll with the specication of the
alloy. Stainless steel used in Emac® products has also been tested with salt spray test, exceeding 500
hours of exposition without signs of corrosion.
Stainless steel is a highly durable and resistent material, with an excellent supercial appearance that
does not degrade along the time. The nishes available are high brightness, brushed or the “futura”
range whose covering contains titanium. All the nishes are slightly porous and smooth, making easier
the hygiene of the installation.
*You can nd out more information by consulting the Technical Files of materials available in www.emac.es
Prole with simple lines made of stainless steel AISI 304 alloy. This
prole has been designed to be installed as an edge protector,
ooring separator, countertop nish... It can be installed with oor or
wall tiles between 8 and 15 mm width. Available in high brightness
nish.
R03.001_11/01/2012
TECHNICAL FILE
Novosuelo/ Novopared Stainless steel
Installation
Page 2 of 3
1. Tile one of the sides of the wall to be tiled. Then, spread a big amount of thin-set mortar on the
other side.
2. Place the Novosuelo/Novopared on the corner and press to let the thin-set mortar pass through
the holes of the anchoring wing.Coloque el Novosuelo/Novopared sobre el ángulo y presione para
que el material de agarre pase a través de los agujeros mecanizados del ala de jación.
3. Place tiles along the anchoring wing and then press them softly to get an optimal adhesion.
4. Continue tiling until the installation is nished
5. Clean the possible leftover and let dry.
Walls
Floors
1 2 3 4 5
1
2
3
4 5
Cleaning and maintenance
To visualize the video, capture
this image with your mobile
(QR code reader software is
required) or just click on it.
1. Spread a big amount of thin-set mortar on the surface to be tiled.
2. Then, place the prole and press it to let the thin-set mortar pass through the holes on the anchoring
wing.
3. Place a tile on the anchoring wing of the prole and press to get an optimal contact with the thin-
set mortar.
4. Repeat the previous step placing tiles along the prole until the installation is nished. Before
curing, tap with a rubber hammer to align the prole with the pavement.
5. Finally clean the leftover material and let dry.
* If you are going to polish the ooring, you must install the prole slightly below the tile to avoid possible damages.
To visualize the video, capture
this image with your mobile
(QR code reader software is
required) or just click on it.
It’s necessary the immediate cleaning of the material after its installation to avoid that remainings of
mortar, concrete or iron particles from wool or tool could cause corrosion.
For outdoor applications, such as facades, the rain is an efcient cleaner. Pay special attention to
difcult access areas and be sure you remove all the remainings of dust and the rest of elements. You
can do this cleaning once per month.
For indoor applications, you can use water with detergent or liquid soap to remove dirtiness and
possible ngerprints marked on the surface. In highly brilliant nishes, you can use a glass cleaner.
There are specic cleaners in the markets for stainless steel which clean the material and reduce
possible stains. Whenever you clean stainless steel, ensure you rinse it well and dry totally to prevent
fogging.
Steel wool or similar products, are not recommended because they could scratch the surface and
create pitting corrosion. Pay special attention while using materials containing chlorides, they are not
indicated because could oxidize the material. Hydrochloric acid or iron products in a long contact with
the material are neither recommended. Do not use cleaners for common steel for the cleaning of
stainless steel.
TECHNICAL FILE
R03.001_11/01/2012
Technical Information
You can nd out more information about the technical features of Emac®’s products by downloading
their Technical File from www.emac.es.
If you have any query please contact our Technical Department in tecnico@emac.es
The data provided are only for information and have been obtained by our supplier or Emac®.
Does not constitute legal guarantee in terms of properties and / or functionality of the application of material
Emac Complementos S.L. (Spain) info@emac.es // Emac America L.L.C. (FL,USA) sales@emac.es // Emac Italia S.R.L. (Italy) [email protected]
www.emac.es
Novosuelo/ Novopared Stainless steel
Page 3 of 3
Indoors Wall tiling Flooring
  • Page 1 1
  • Page 2 2
  • Page 3 3

Emac NLX1638NP Guide d'installation

Taper
Guide d'installation

dans d''autres langues