Matrox FastNIC 10/100 10574-MT-0102 Manuel utilisateur

Marque: Matrox

Modèle: FastNIC 10/100 10574-MT-0102

Taper: Manuel utilisateur

Ce manuel convient également à

Matrox FastNIC 10/100

Single Port Fast Ethernet 100BaseTX NIC

PCI Network Interface Card

Installation Guide

10574-MT-0102

The Matrox FastNIC 10/100 is a high-performance Fast Ethernet adapter card,

ideal for typical and “power user” PC workstations. The FastNIC installs into a

standard bus-mastering PCI slot. Driver support is provided for most popular

network operating systems.

Before You Begin

Verify the contents of your package. It should contain the following items:

• Matrox FastNIC 10/100

• Software driver diskette

• Registration card

•This guide

NOTE:

If any of these items are missing, contact your Matrox Networks

representative.

System Requirements

The FastNIC is a standard PCI device. The BIOS of the PC into which the

FastNIC will be installed must conform to the PCI Local Bus Specification v2.0/

2.1. The PCI slot into which you will insert the card must support PCI bus

mastering. If necessary, refer to the documentation that came with the PC for

information regarding its compliance to the PCI standard.

Installing the Card

To install the FastNIC in a PC, perform the following steps:

1. Turn off your PC.

2. Open the case of your PC and locate an empty PCI expansion slot.

3. Unbolt and remove the blank panel adjacent to the PCI slot you will use

for the FastNIC.

4. Carefully insert the FastNIC card into the PCI expansion slot as shown

in the following diagram:

5. Secure the FastNIC card in place with the bolt that previously held the

blank panel you removed previously.

6. Replace the cover of the PC.

Selecting the Right Cable

The FastNIC is a standard Fast Ethernet adapter card. To connect the

FastNIC to another Fast Ethernet device, you must use unshielded twisted-

pair (UTP) Category 5 wiring.

NOTE:

If you only plan to operate the FastNIC at 10Mbps, you can use UTP

Category 3 wiring instead.

Most Fast Ethernet adapters connect to other Fast Ethernet devices through

“straight-through” cables. You may have to use a special cable called a

“cross-over” cable, under the following circumstances:

• When connecting directly to the Fast Ethernet adapter of another PC.

• When connecting to the “Uplink” port of a hub or switch.

• When connecting to any other Ethernet port labeled “MDI.”

Installing the Software Drivers

Software drivers are supplied for the following network operating systems:

• Microsoft Windows NT

• Microsoft Windows 95

• Microsoft Windows for Workgroups

• Novell NetWare

• LAN Manager

•OS/2

• SCO UNIX

NOTE:

Installation instructions for Windows 95, Windows NT, and Novell

NetWare (DOS client) are provided below. For other network operating

systems, please consult the documentation that came with the network

operating system for information on how to install and configure client PC

drivers.

Windows 95

To install the software driver for the Windows 95 operating system, please

perform the following steps:

1. Double-click on the following icons:

2. Click on the Add button:

3. Click on the Have Disk button:

4. Insert the driver diskette into the PC’s floppy drive. Specify the

directory a:\win95 and click OK:

5. By default, the Fast NIC is configured for AutoDetect mode. However,

you can use the Properties window to force the speed and duplex

settings of the card:

Windows NT

To install the software driver for the Windows NT operating system, please

perform the following steps:

1. Double-click on the following icons:

2. Click on the Add button:

3. Click on the Have Disk button:

4. Insert the driver diskette into the PC’s floppy drive. Specify the

directory a:\winnt and click OK:

5. By default, the Fast NIC is configured for AutoDetect mode. However,

you can use the Properties window to force the speed and duplex

settings of the card:

Novell NetWare (DOS Client)

To install the driver support software for a Novell NetWare DOS client,

perform the following steps:

1. Copy the contents of the a:\novell directory to the c:\nwclient directory

on the PC:

copy a:\netware\client\dos\*.* c:\nwclient

NOTE:

If necessary, substitute the appropriate directory name if

c:\nwclient

is not the name of the directory containing the NetWare

client software.

2. Use the DOS Edit command to create a batch file called

startnet.bat

that contains the following commands:

c:\nwclient\lsl

c:\nwclient\l100

c:\nwclient\ipxodi

c:\nwclient\vlm

Understanding the Status Lights

Troubleshooting

A diagnostic utility is supplied with the FastNIC to assist you with

troubleshooting.

Diagnostic Utility

Please test the FastNIC before you call Technical Support. To test the FastNIC,

insert the diskette labeled “FastNIC drivers” into the floppy drive of the PC,

and enter the following command from a command prompt:

a:\ezshoot\shooter

Select the option Diagnose | Diagnosis. If the diagnostic utility indicates an

error, refer to its online help system for troubleshooting information.

Other Troubleshooting Information

This section describes typical problems you may encounter during installation

or configuration, and provides suggested solutions for those problems.

Please refer also to the online help system supplied with the diagnostic utility.

ROBLEM

No communication between the FastNIC and other devices connected to the

network.

OLUTION

#1:

Verify the physical connection of the FastNIC to the hub or switch. Ensure that

physical connectors are firmly inserted at both ends of the cable connecting

the FastNIC to the LAN.

10/100Mb

ACT

LNK

100

OLUTION

#2:

The device may require a cross-over or straight-through wire in order to

connect to the other device. Refer to the instructions contained in section D

to determine which kind of wire to use in order to connect a specific type of

device.

Obtaining Technical Support

Please complete and mail the registration card.

If you are unable to solve a particular problem with installation or

configuration, you can contact Matrox Networks for technical support.

World Wide Web

Updated troubleshooting information is made available through our website

on an ongoing basis:

www.matrox.com/networks

E-mail

We will respond to your e-mailed questions within one business day:

networks.techsupport@matrox.com

Telephone

Technical support is available by telephone Monday through Friday, from

9:00AM to 5:00PM Eastern Time:

(514) 969-6090

Specifications

Standard IEEE802.3/802.3u 10BaseT/100BaseTX

Bus Interface 32 bit bus master

Hardware Interrupts PCI INTA

Base I/O Addresses Assigned by BIOS

Cable Connections RJ-45 (10BaseT) UTP Category 3 and higher.

RJ-45 (100BaseTX) UTP Category 5.

Software Support

• Microsoft Windows NT

• Microsoft Windows 95

• Microsoft Windows for Workgroups

• Novell NetWare

• LAN Manager

•OS/2

• SCO UNIX

Operating

Tem pe r at ur e

0°C - 55°C (32°F - 131°F)

Storage

Tem pe ra tu re

-20°C - 70°C (-4°F - 158°F)

Operating Humidity 10% - 90%

Storage Humidity 5% - 95%

EMC Compliance FCC Class B, CE Mark

Dimensions 125mm x 94mm

Power

Consumption

2W maximum

1.25W Typical

Regulatory Compliance

FCC Compliance Statement

Warning

Changes or modifications to this unit not expressly approved by the party

responsible for the compliance could void the user’s authority to operate this

equipment.

Note

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Industry Canada Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise

emission from digital apparatus set out in the Radio Interference Regulations of

Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant

les limites applicables aux appareils numériques de Classe B prescrites dans le

Règlement sur le brouillage radioélectrique édicté par Industrie Canada.

Matrox FastNIC 10/100 10574-MT-0102 Manuel utilisateur

Marque: Matrox

Modèle: FastNIC 10/100 10574-MT-0102

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Matrox FastNIC 10/100 10574-MT-0102 User manual

Matrox FastNIC 10/100 10574-MT-0102 Manuel utilisateur

Ce manuel convient également à

Matrox FastNIC 10/100 10574-MT-0102 Manuel utilisateur

dans d''autres langues

Autres documents