Bull NovaScale T810 F2 Guide de démarrage rapide

NovaScale T810 F2

Getting Started With Your

System

Guide de mise en route

NOVASCALE

REFERENCE

86 X1 76FD 00

NOVASCALE

NovaScale T810 F2

Getting Started With Your System

Guide de mise en route

Hardware/Matériel

December/Décembre 2009

BULL CEDOC

357 AVENUE PATTON

B.P.20845

49008 ANGERS CEDEX 01

FRANCE

REFERENCE

86 X1 76FD 00

The following copyright notice protects this book under Copyright laws which prohibit such actions as, but not limited

to, copying, distributing, modifying, and making derivative works.

2009

Trademarks and Acknowledgements

Citrix and XenServer are trademarks of Citrix Systems, Inc. and/or more of its subsidiaries, and may be registered in

the United States

Patent and Trademark Office and in other countries. Intel and Xeon are registered trademarks of Intel

Corporation in the U.S. and other countries; Microsoft, Hyper-V, Windows, and Windows Server are

either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other

countries. Red Hat and Enterprise Linux are registered trademarks of Red Hat, Inc. in the United States

and other countries; SUSE is a registered trademark of Novell, Inc., in the United States and other

countries. VMware is a registered trademark of VMware, Inc. in the United States and/or other

jurisdictions.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Bull disclaims any proprietary interest in trademarks and

trade names other than its own.

We acknowledge the rights of the proprietors of the trademarks mentioned in this manual.

All brand names and software and hardware product names are subject to trademark and/or patent protection.

Quoting of brand and product names is for information purposes only and does not represent trademark

misuse.

The information in this document is subject to change without notice. Bull will not be liable for errors

contained herein, or for incidental or consequential damages in connection with the use of this material.

Getting Started

With Your System

intercalaire_EN.fm Page 1 Tuesday, April 20, 2010 1:29 PM

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use

of your computer.

WARN ING : A WARNING indicates a potential for property damage,

personal injury, or death.

____________________

intercalaire_EN.fm Page 2 Tuesday, April 20, 2010 1:29 PM

Getting Started With Your System 3

Installation and Configuration

WA RNIN G: Before performing the following procedure, review the safety

instructions that came with the system.

Unpacking the System

Unpack your system and identify each item.

Optional – Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable to

plug into each connector. Be sure to tighten the screws (if any) on the monitor's

cable connector.

section.fm Page 3 Tuesday, April 20, 2010 1:31 PM

4 Getting Started With Your System

Connecting the Power Cable

CAUTION: Be sure to set the voltage selection switch on the power supply for

the voltage that most closely matches the AC power available at your location.

Connect the system’s power cable to the system and, if a monitor is used,

connect the monitor’s power cable to the monitor.

Securing the Power Cable

Bend the system power cable into a loop as shown in the illustration and attach

to the cable clasp.

section.fm Page 4 Tuesday, April 20, 2010 1:31 PM

Getting Started With Your System 5

Plug the other end of the power cable into a grounded electrical outlet or

a separate power source such as an uninterrupted power supply (UPS) or

a power distribution unit (PDU).

NOTE: Ensure that the system is connected to a stand-alone power source with

stable power supply for better performance.

Turning On the System

Press the power button on the system. The power indicator should light.

section.fm Page 5 Tuesday, April 20, 2010 1:31 PM

6 Getting Started With Your System

Operating System Installation

The NovaScale T810 F2 offers an embedded Configuration utility: the Unified

Server Configurator (USC), which includes an OS Deployment Wizard that

assists you with the installation of the Operating System.

Refer to the technical characteristics of the server on

http://www.bull.com/novascale

to get the list of supported operating systems.

NOTE: The list of operating systems offered by the USC may be larger than the

list of the supported Operating Systems.

NOTE: for the installation of a supported Operating System not listed in the USC,

see

http://support.bull.com

.

Residing on an embedded flash memory card, USC is similar to a BIOS utility

in that it can be started during the boot sequence and can function independently

of an installed operating system.

The USC of the NovaScale T810 F2 server does not provide an operating

system drivers repository that may be required for operating system installation.

You have to use a local USB source that has drivers on it, in a specific format to

be read by USC. To get the most up-to-date version of the drivers, it is advised

to download the drivers repository from the Bull Support web site. The

downloaded .iso file has to be burnt to a CDROM which will be used as a local

USB source for the USC.

A drivers repository is also included in the "Bull NovaScale Universal

R400/T800 Series - Resource CD" CDROM shipped with the server.

The OS Deployment wizard extracts these drivers and copies them to a staging

directory. These files are deleted after an 18-hour period or when you press the

<F10> key to either cancel operating system installation or re-enter USC after

rebooting.

NOTE: During the 18-hour period when the drivers are extracted to the temporary

location, you cannot update USC, drivers, or diagnostics using a Driver Update

Package after the operating system is installed, or the Driver Update Package will

display a message that another session is open.

For supported Microsoft® Windows® operating systems, these extracted

drivers are installed during the operating system installation. For supported

Linux operating systems, you must manually install the extracted drivers after

the operating system installation is complete.

section.fm Page 6 Tuesday, April 20, 2010 1:31 PM

Getting Started With Your System 7

Before installing the operating system, the OS Deployment wizard detects if a

boot device is available. A boot device is a physical disk, virtual disk, or other

storage device on which the operating system can be installed.

To begin installation

1

Connect the keyboard, monitor, mouse, and any additional peripherals to

your system.

2

Turn on the system and the attached peripherals.

3

Press

<F10>

in the POST to start the System Services.

NOTE: The Initializing UEFI. Please wait... and the Entering System Services...Starting

Unified Server Configurator messages are displayed.

NOTE: : If <F10> is not available because the System Services is disabled, press <Ctrl E>

in the POST when the message is displayed, to enter in the BMC configuration utility.

Select System Services and press Enter. Set System Services to "Enable". Exit the tool by

saving the changes . At next reboo

t <F10> must be available.

4

Insert the "Bull NovaScale Universal R400/T800 Series - Resource CD"

CDROM in the DVD drive

5

Click

OS Deployment

in the left pane.

6

Click

Deploy OS

in the right pane.

7

Click

8

Select

Local Drive (CD/DVD/USB)

and click

9

Select the repository in the drop down list and click

NOTE: In the Select Media drop down list, the reference of the "Bull NovaScale Universal

R400/T800 Series - Resource CD" CDROM is displayed.

NOTE: : If your system has a RAID controller, you have the option of launching the RAID

Configuration wizard and configuring a virtual disk as the boot device.

If your system does not have a RAID controller or if you choose to bypass the optional RAID

configuration, the OS Deployment wizard installs the operating system to a default location,

which is typically the disk identified as Disk 0 in the BIOS utility

10

Select the operating system you want to install and click

section.fm Page 7 Tuesday, April 20, 2010 1:31 PM

8 Getting Started With Your System

11

USC extracts the drivers required by the operating system you selected.

NOTE: For Red Hat® Enterprise Linux® 4.x server and Red Hat Enterprise Linux 5.x

server, the drivers are extracted to OEMDRV under /oemdrv/*.rpm.

For SUSE® Linux Enterprise Server 10 SP2, the drivers are extracted under

/linux/suse/x86_64-sles10/install/*.rpm.

NOTE: The process for extracting the drivers may take several minutes.

NOTE: All drivers copied by the OS Deployment wizard are removed after 18 hours. You

must complete the operating system installation within 18 hours for the copied drivers to be

available. To remove the drivers before the 18-hour period is over, reboot the system and

press the <F10> key to re-enter USC.

12

After the drivers are extracted, USC prompts you to insert the operating

system installation media.

NOTE: When installing the Microsoft Windows operating system, the extracted drivers are

automatically installed during the operating system installation. When installing the Linux

operating system, the operating system installation uses native drivers. After the Linux

installation is complete, you need to manually install the drivers extracted by USC. See

"Update Drivers for Linux Systems Only".

13

Insert the operating system installation media when prompted and click

NOTE: USC supports internal SATA optical drives and USB optical drives. If the

installation media is corrupt or not readable, then USC may be unable to detect the presence

of a supported optical drive. In this case, you may receive an error message stating that no

optical drive is available. If the media is not valid (if it is the incorrect CD or DVD, for

example), a message displays requesting that you insert the correct installation media

14

Click Finish to reboot the system and continue with the operating system

installation. Upon reboot, the system boots to the operating system

installation media.

NOTE: When the system reboots after you click Finish, you may be prompted to press a

key before booting to the operating system installation media. If you do not press a key, the

system boots to the hard drive and not the operating system installation media.

NOTE: : In the event that the operating system installation is interrupted and the system

reboots before installation completes, you may be prompted to press a key in order to boot

from the operating system installation media.

NOTE: You can cancel the operating system installation by pressing the <F10> key.

Pressing the <F10> key at any point during the installation process or while rebooting causes

any drivers provided by the OS Deployment wizard to be removed.

NOTE: Microsoft Windows Server 2008 UEFI operating system installations are not

currently supported.

CAUTION: During Red Hat 5.x installation, you will receive a warning that a read-only

file system was detected; Linux has detected the temporary storage area of USC that stores

updates for your system. Click OK, and a second warning will appear indicating that the

section.fm Page 8 Tuesday, April 20, 2010 1:31 PM

Getting Started With Your System 9

read-only file system has a loop partition layout and that it needs to be formatted. Click the

Ignore drive button. You may see both warnings several times during the course of Red Hat

5.x installation.

CAUTION: During the beginning of Windows Server® 2003 installation, the installer

will automatically detect and possibly assign the default drive letter C to the USC temporary

storage device OEMDRV. Creating a new Windows-bootable system partition on the hard

drive will assign the partition to a drive letter other than C; this is standard Windows

installer behaviour. To assign the new partition to C, see "Assign a Windows-Bootable

System Partition to the C: Drive".

Update Drivers for Linux Systems Only

On the following operating systems, it is advised to update your system with the

extracted drivers after installation. The drivers are extracted to a drive (or

device) named OEMDRV.

• Red Hat Enterprise Linux 4.7 server - The location of the drivers on the

OEMDRV drive after installation is:

/oemdrv/*.rpm

• Red Hat Enterprise Linux 5.2 server - The location of the drivers on the

OEMDRV drive after installation is:

/oemdrv/*.rpm

• SUSE Linux Enterprise Server 10 with Service Pack 2 - The location of the

drivers on the OEMDRV drive after installation is:

/linux/suse/x86_64-

sles10/install/*.rpm

Use the following command to install the drivers: rpm -Uvh *.rpm.

NOTE: If the command rpm –Uvh *.rpm fails to install a driver because a newly

version of the DKMS package is needed, see the

http://support.bull.com

website to

download the latest version of the DKMS package, then:

• install this DKMS package by launching the command:

rpm –Uvh dkms <version-release>.noarch.rpm

• install the Linux drivers by launching the command:

find ./* -not –name dkms* -exec rpm –Uvh {} \;

Kickstart Installation for the Linux Operating System

If you are using a kickstart installation for the Linux operating system, provide

the following information in the post-installation script:

section.fm Page 9 Tuesday, April 20, 2010 1:31 PM

10 Getting Started With Your System

• Command to mount the USB device containing the operating system drivers

labeled OEMDRV.

For example:

mkdir OEMDRV

mount /dev/sdc1 /mnt/OEMDRV

• Path to the operating system drivers on the OEMDRV drive:

For Red Hat Enterprise Linux:

/oemdrv/*.rpm

For SUSE Linux Enterprise Server:

/linux/suse/x86_64-sles10/install/*.rpm

• Command to install the drivers:

rpm -Uvh *.rpm

Assign a Windows-Bootable System Partition to the C: Drive

After you have completed the USC portion of Windows Server 2003

installation, your server will reboot and begin the text-mode portion of the

installation. During this phase, you may need to perform the following steps to

ensure Windows installs to your C: drive.

NOTE: Following these instructions after Windows Server 2003 setup presents

you with a list of existing drive partitions and/or unpartitioned space available on

your computer.

1

Select the unpartitioned space, and then press <c> to create a hard-disk

partition. Follow the on-screen instructions to create a partition.

NOTE: The partition may not be enumerated as a C: drive.

2

Select the newly-created partition, and then press <d> to delete the partition.

Follow the on-screen instructions to delete the partition.

3

Select the unpartitioned space again, and then press <c> to create a primary

hard-disk partition.

NOTE: The partition will now be enumerated as C: drive.

4

Follow the on-screen instructions to create a partition. Windows will now

install on the C: drive.

For more information on assigning the Windows-bootable system partition to

the C: drive, see

http://support.microsoft.com/kb/896536

.

Other Information You May Need

WARN ING : See the safety and regulatory information that shipped with your

system. Warranty information may be included within this document or as

a separate document.

section.fm Page 10 Tuesday, April 20, 2010 1:31 PM

Getting Started With Your System 11

• The rack documentation included with your rack solution describes how to

install your system into a rack.

•The

Hardware Owner’s Manual

provides information about system features

and describes how to troubleshoot the system and install or replace system

components. This document is available online at

http://support.bull.com/documentation.

• Any media that ships with your system that provides documentation and

tools for configuring and managing your system, system management

software, system updates, and system components that you purchased with

your system.

NOTE: Always check for updates on

http://support.bull.com

and read the

updates first because they often supersede information in other documents.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does not

perform as expected, see

http://support.bull.com/documentation

for further

documentation, or contact your support representative; the phone directory is at

http://support.bull.com

.

section.fm Page 11 Tuesday, April 20, 2010 1:31 PM

12 Getting Started With Your System

Technical Specifications

Processor

Processor type Intel

®

Xeon

®

Processor 3400 series

Expansion Bus

Bus type PCI Express Generation 2

Expansion slots: Slot 1: PCIe x8 (x8 routing), half-length

Slot 2: PCIe x16 (x8 routing), full-length

Slot 3: PCIe x8 (x4 routing), half-length

Slot 4: PCIe x1 (x1 routing), half-length

Memory

Architecture 1066-MHz or 1333-MHz DDR3 unbuffered

Error Correcting Code (ECC) DIMMs

Memory module sockets Four 240-pin

Memory module capacities 1 GB, 2 GB, or 4 GB

Minimum RAM 1 GB

Maximum RAM 16 GB

Drives

Hard drives Up to four 3.5-inch, cabled SAS or SATA

internal drives

Optical drive Optional internal SATA DVD-ROM or SATA

DVD+/-RW

Optional external USB DVD-ROM

NOTE: DVD devices are data only.

Tape drive One optional internal half-height tape backup

device

section.fm Page 12 Tuesday, April 20, 2010 1:31 PM

Getting Started With Your System 13

Connectors

Back

NIC

One RJ-45 (for integrated 1-GB NIC)

Serial

9-pin, DTE, 16550-compatible

USB

Four 4-pin, USB 2.0-compliant

Video

15-pin VGA

eSATA

One 7-pin connector

Front

USB

Two 4-pin, USB 2.0-compliant

Internal

USB

Two 4-pin, USB 2.0-compliant

Video

Video type Matrox G200, integrated in Winbond

WPCM450

Video memory 8 MB

Power

AC power supply (per power supply)

Wattage

305 W

Vo l t a g e

90-135 VAC (115 V)/180-264 VAC (230 V),

50/60 Hz, 9-4.5 A

Heat dissipation

1776 BTU/hr maximum

Maximum inrush current

Under typical line conditions and over the

entire system ambient operating range,

the inrush current may reach 35 A per power

supply for 10 ms or less.

Batteries

System battery

CR 2032 3.0-V lithium ion coin cell

section.fm Page 13 Tuesday, April 20, 2010 1:31 PM

14 Getting Started With Your System

Physical

Height 42.03 cm (16.55 in)

Width 18.9 cm (7.44 in)

Depth 46.38 cm (18.26 in)

Weight (maximum configuration) 15.49 kg (34.14 lb)

Environmental

Temperature

Operating

10° to 35°C (50° to 95°F) with a maximum

temperature gradation of 10°C per hour

NOTE: For altitudes above 2950 feet,

the maximum operating temperature

is derated 1ºF/550 ft.

Storage

–40° to 65°C (–40° to 149°F) with a maximum

temperature gradation of 20°C per hour

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage

5% to 95% (noncondensing)

Maximum vibration

Operating

0.26 Grms at 5–350 Hz for 15 min

Storage

1.54 Grms at 10–250 Hz for 15 min

section.fm Page 14 Tuesday, April 20, 2010 1:31 PM

Getting Started With Your System 15

Maximum shock

Operating

One shock pulse in the positive z axis

(one pulse on each side of the system) of 31 G

for 2.6 ms in the operational orientation

Storage

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes

(one pulse on each side of the system) of 71 G

for up to 2 ms

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one

pulse on each side of the system) of 32 G faired

square wave pulse with velocity change at 270

inches/second (686 centimeters/second)

Altitude

Operating

–16 to 3,048 m (–50 to 10,000 ft)

NOTE: For altitudes above 2950 feet,

the maximum operating temperature

is derated 1ºF/550 ft.

Storage

–16 to 10,600 m (–50 to 35,000 ft)

Airborne Contaminant Level

Class

G2 or lower as defined by ISA-S71.04-1985

Environmental (continued)

section.fm Page 15 Tuesday, April 20, 2010 1:31 PM

16 Getting Started With Your System

section.fm Page 16 Tuesday, April 20, 2010 1:31 PM

La page est en cours de chargement...

Bull NovaScale T810 F2 Guide de démarrage rapide

Bull NovaScale T810 F2 Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents