JennAir JXW8936DS Manuel utilisateur

Marque: JennAir

Modèle: JXW8936DS

Catégorie: Hottes

Taper: Manuel utilisateur

Ce manuel convient également à

JENN-AIR

36" (91.4 CM) WALL-MOUNT

CANOPY RANGE HOOD

HOTTE DE CUISINIÈRE JENN-AIR

POUR

MONTAGE MURAL 36" (91,4 CM)

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call:

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.ca.

Instructions d’installation et Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service, composez le 1-800-JENNAIR (1-800-536-6247) ou visitez notre site web

à www.jennair.ca.

Table of Contents/Table des matières .....................................2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONL

IMPOR

TANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISA

TION RÉSIDENTIELLE UNIQUEMENT

2845/W10640309D

TABLE OF CONTENTS TABLE DES MATIÈRES

RANGE HOOD SAFETY .................................................................3

INSTALLATION REQUIREMENTS ................................................. 5

Tools and Parts .............................................................................5

Location Requirements ................................................................5

Venting Requirements ..................................................................6

Electrical Requirements ...............................................................7

INSTALLATION INSTRUCTIONS ................................................... 9

Prepare Location ..........................................................................9

Install Range Hood .....................................................................11

Connect Vent System ................................................................11

Reinstall Motor ...........................................................................12

Make Electrical Connection .......................................................12

Install Chimney Covers ..............................................................13

Complete Installation .................................................................14

RANGE HOOD USE ......................................................................14

Controls and Features ................................................................ 14

RANGE HOOD CARE ...................................................................15

Cleaning .....................................................................................15

WIRING DIAGRAM .......................................................................17

ASSISTANCE OR SERVICE .........................................................18

In the U.S.A. ..............................................................................18

In Canada ...................................................................................18

Accessories ................................................................................18

WARRANTY ..................................................................................19

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE ...............................20

EXIGENCES D’INSTALLATION ...................................................22

Outils et pièces ...........................................................................22

Exigences d’emplacement .........................................................22

Exigences concernant l’évacuation ...........................................23

Spéciﬁcations électriques ..........................................................25

INSTRUCTIONS D’INSTALLATION .............................................27

Préparation de l’emplacement ...................................................27

Installation de la hotte ................................................................29

Raccordement du circuit d’évacuation ...................................... 29

Remontage du moteur ...............................................................30

Raccordement électrique ...........................................................30

Installer les cache-conduits .......................................................31

Achever l’installation ..................................................................32

UTILISATION DE LA HOTTE .......................................................32

Commandes et caractéristiques ................................................32

ENTRETIEN DE LA HOTTE .........................................................34

Nettoyage ...................................................................................34

SCHÉMA DE CÂBLAGE ...............................................................36

ASSISTANCE OU SERVICE .........................................................37

Au Canada ..................................................................................37

Accessoires ................................................................................37

GARANTIE .....................................................................................38

RANGE HOOD SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

IMPORTA NT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools

listed here.

Tools needed:

■ Level

■ Drill with 1

" (3.0 cm) and

" (5.0 mm) drill bits

■ Pencil

■ Wire stripper or utility knife

■ Tape measure or ruler

■ Pliers

■ Caulking gun and weatherproof caulking compound

■ Vent clamps

■ Jigsaw or keyhole saw

■ Flat-blade screwdriver

■ Metal snips

■ Phillips screwdriver

■ TORX

®†

T20

®†

bit or driver

Parts needed:

For hard wire installations, you will also need:

■ Home power supply cable

■

" (12.7 mm) UL listed or CSA approved strain relief

For vented installations, you will also need:

■ 1 wall or roof cap

■ Metal vent system

For non-vented (recirculating) installations, you will

also need:

■ Chimney Kit Recirculation for non-vented (recirculating)

installations only. See the “Assistance or Service” section to

order.

■ Charcoal Filter Kit Part Number W10272069.

See the “Assistance or Service” section to order.

Parts supplied:

Remove parts from packages. Check that all parts are included.

■ Hood canopy assembly with ventilator and lights installed

■ Vent mounting boss (attached to hood canopy assembly)

■ Damper

■ 3 - 3.5 x 9.5 mm screws damper to mounting boss

■ Metal grease ﬁlter installed in hood canopy

■ Chimney cover support bracket

■ 2-piece chimney cover

■ 2 - 8 x 80 mm hanger bolts (TORX

T20

drive)

■ 2 - 8 mm nuts

■ 2 - ﬂat washers

■ 2 - 5 x 40 mm TORX

T20

drive screws for chimney

bracket mounting.

■ 2 - 5 mm wall anchors

■

" (13 mm) special nut tightening tool

■ 2 - plastic spacers for lower chimney

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualiﬁed technician install the range hood. It is the

installer’s responsibility to comply with installation clearances

speciﬁed on the model/serial/rating plate. The model/serial/

rating plate is located behind the left ﬁlter on the rear wall of

the vent hood.

Canopy hood location should be away from strong draft

areas, such as windows, doors, and strong heating vents.

Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance.

The canopy hood mounting location must be capable

of supporting 100 lbs (45.4 kg).

This range hood is recommended for use with cooktops

with a maximum total rating of 78,000 BTUs or less.

Grounded electrical outlet is required. See the “Electrical

Requirements” section.

For non-vented (recirculating) Installation see “Non-vented

(recirculating) Installations” in the “Install Range Hood” section.

Chimney Kit Recirculation and Charcoal Filter Kit Part Number

W10272069 are available from your dealer or an authorized parts

distributor. See the “Assistance or Service” section to order.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations:

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities

and Setups) ANSI A225.1/NFPA 501A or latest edition, or

with local codes.

Product Dimensions

A. 12

" (31.4 cm)

B. 13

" (33.4 cm)

C. 36" (91.4 cm)

D. 19

" (50.1 cm)

E. 2

" (6.0 cm)

F. 25

" (65.0 cm)

G. 33

" (86.0 cm) min.

" (141.0 cm) max.

TORX and †®T20 are registered trademarks of Acument Intellectual Properties, LLC.

Cabinet Dimensions

*For non-vented (recirculating) installations

IMPORTANT:

Minimum distance “X”: 24" (61.0 cm) from electric

cooking surface

Minimum distance “X”: 30" (76.2 cm) from gas

cooking surface

Suggested maximum distance “X”: 36" (91.4 cm)

NOTE: For best performance of the Auto Sense feature, the

range hood should be installed at 24" (61.0 cm) from an electric

cooking surface and 30" (76.2 cm) from a gas cooking surface.

The chimneys can be adjusted for different ceiling heights.

See the following chart.

*NOTE: The range hood chimneys are adjustable and designed

to meet varying ceiling or sofﬁt heights, depending on the

distance “X” between the bottom of the range hood and

the cooking surface. For higher ceilings from 10' 4" to 12'

(3.24 m to 3.66 m), a Stainless Steel Chimney Extension Kit

is available from your dealer or an authorized parts distributor.

The chimney extension replaces the upper chimney shipped

with the range hood. See the “Assistance or Service” section to

order.

Venting Requirements

(vented models only)

■ Vent system must terminate to the outdoors, except for

non-vented (recirculating) installations.

■ Do not terminate the vent system in an attic or other

enclosed area.

■ Do not use 4" (10.2 cm) laundry-type wall cap.

■ Use metal vent only. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

■ The length of vent system and number of elbows should

be kept to a minimum to provide efﬁcient performance.

For the most efﬁcient and quiet operation:

■ Use no more than three 90° elbows.

■ Make sure there is a minimum of 24" (61.0 cm) of straight

vent between the elbows if more than 1 elbow is used.

■ Do not install 2 elbows together.

■ Use clamps to seal all joints in the vent system.

■ The vent system must have a damper. If the roof or wall

cap has a damper, do not use the damper supplied with

the range hood.

■ Use caulking to seal exterior wall or roof opening around

the cap.

■ The size of the vent should be uniform.

Cold Weather Installations:

An additional back draft damper should be installed to minimize

backward cold air ﬂow and a thermal break should be installed

to minimize conduction of outside temperatures as part of the

vent system. The damper should be on the cold air side of the

thermal break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup Air:

Local building codes may require the use of makeup air systems

when using ventilation systems greater than speciﬁed CFM of

air movement. The speciﬁed CFM varies from locale to locale.

Consult your HVAC professional for speciﬁc requirements in

your area.

Venting Methods

This canopy hood is factory set for venting through the roof

or wall.

A 6" (15.2 cm) round vent system is needed for installation (not

included). The hood exhaust opening is 6" (15.2 cm) round.

A 6" to 8" (15.2 cm to 20.3 cm) vent adapter is available for 8"

(20.3 cm) vent systems. See the “Assistance or Service” section

to order.

Vent system can terminate either through the roof or wall.

To vent through a wall, a 90° elbow is needed.

Rear discharge:

A 90° elbow may be installed immediately above the hood.

10" (25.4 cm) min.

13" (33.0 cm) max.

9¹⁄₂" (24.1 cm)

2" (5.1 cm) min.

9" (22.9 cm) min.*

Centerline

Side

cabinet

Side

cabinet

Vent and po

wer

supply cable

entry location

20³⁄₈" (51.8 cm)*

36" (91.4 cm)

“X”

bottom of

canopy

to cooking

surface

10" (25.4 cm) min.

13" (33.0 cm) max.

Cooking surface

Vented Installations

Min. ceiling height Max. ceiling height

Electric cooking

surface

7' 10" (2.39 m) 10' 4" (3.24 m)

Gas cooking

surface

8' 4" (2.54 m) 10' 4" (3.24 m)

Non-Vented (Recirculating) Installations

Min. ceiling height Max. ceiling height

Electric cooking

surface

7' 10" (2.39 m) 10' 4" (3.24 m)

Gas cooking

surface

8' 4" (2.54 m) 10' 4" (3.24 m)

For Non-Vented (recirculating) Installations:

If it is not possible to vent cooking fumes and vapors to the

outside, the hood can be used in the non-vented (recirculating)

version, ﬁtting a charcoal ﬁlter and the deﬂector. Fumes and

vapors are recycled through the upper chimney cover louvers.

To order the charcoal ﬁlter and recirculation kit, see

“Accessories” in the “Assistance and Service” section.

Roof Venting

A. Roof cap

B. 6" (15.2 cm)

round vent

A. Wall cap

B. 6" (15.2 cm)

round vent

A. Deﬂector

B. 6" (15.2 cm)

round vent

Wall Venting

Non-Vented

(recirculating)

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Maximum equivalent vent length is 35 ft (10.7 m).

Example vent system:

The following example falls within the maximum recommended

vent length of 35 ft (10.7 m).

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70

(latest edition), or CSA Standards C22.1-94, Canadian Electrical

Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local

codes and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■ A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit

is required.

Vent Piece 6" (15.2 cm) Round

45° elbow 2.5 ft (0.8 m)

90° elbow 5.0 ft (1.5 m)

90 elbow

6 ft (1.8 m)

2 ft

(0.6 m)

Wall cap

1 - 90° elbow = 5.0 ft (1.5 m)

1 - wall cap = 0.0 ft (0.0 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

Length of system = 13.0 ft (3.9 m)

For 3 Prong Grounded Power Cord:

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

■ This range hood is equipped with a power supply cord

having a 3 prong grounding plug.

■ To minimize possible shock hazard, the cord must be

plugged into a mating, 3 prong, grounding-type outlet,

grounded in accordance with local codes and ordinances.

If a mating outlet is not available, it is the responsibility of

the customer to have the properly grounded outlet installed

by a qualiﬁed electrician.

■ The grounded 3 prong outlet is to be located above the

range hood at a maximum distance of 40" (101.6 cm) from

where the power cord exits the hood. See illustration.

40"

(101.6 cm)

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■

For a grounded, cord-connected range hood:

This range hood must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of electric

shock by providing an escape wire for the electric current.

This range hood is equipped with a cord having a grounding

wire with a grounding plug. The plug must be plugged into

an outlet that is properly installed and grounded.

WARNING: Improper grounding can result in a risk of

electric shock.

Consult a qualified electrician if the grounding instructions

are not completely understood, or if doubt exists as to

whether the range hood is properly grounded.

Do not use an extension cord. If the power supply cord is too

short, have a qualified electrician install an outlet near the

range hood.

For Hard Wire from Home Power Supply:

■ If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the

pigtail leads.

2. Connect the aluminum wiring to the added section

of copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer’s recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating of

the appliance as speciﬁed on the model/serial/rating plate.

The model/serial/rating plate is located behind the ﬁlter on

the rear wall of the range hood.

■ Wire sizes must conform to the requirements of the

National Electrical Code, ANSI/NFPA 70 (latest edition),

or CSA Standards C22. 1-94, Canadian Electrical Code,

Part 1 and C22.2 No. 0-M91 (latest edition), and all local

codes and ordinances.

INSTALLATION INSTRUCTIONS

Prepare Location

■ It is recommended that the vent system be installed before

hood is installed.

■ Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

■ Check your ceiling height and the hood height maximum

before you select your hood.

1. Disconnect power.

2. Determine which venting method to use: roof, wall,

or non-vented.

3. Select a ﬂat surface for assembling the range hood.

Place covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

4. Using 2 or more people, lift range hood onto

covered surface.

5. Remove the motor from the canopy assembly (see the

“Motor Removal” section in this section).

Motor Removal

To remove motor:

1. Remove the ﬁlter cover and metal grease ﬁlter (see the

“Metal Grease Filters” section in the “Range Hood Care”

section).

2. Disconnect the blower motor wiring at the 9-pin connector.

3. Locate the special

" (13 mm) tool inside the range hood

blower housing in the left front corner behind the insulation

pad. Use it to loosen the 4 nuts located inside the blower

housing that mounts the motor to the module top cover.

4. Grasp the motor plate and slide the motor toward the

back of the module housing to the large openings in the

keyhole slots.

A. Special

" (13 mm) tool

B. Motor assembly

C. Keyhole slots (large opening) (4)

" (13 mm) motor mounting nuts (4)

E. Motor plate

F. Module top cover

5. Remove the motor from the range hood.

A. Blower housing

B. Keyhole slots (4)

C. Motor assembly

D. Motor plate

Range Hood Mounting Screws Installation

1. Determine and mark the centerline on the wall where the

canopy hood will be installed.

2. Select a mounting height between a minimum of 24"

(61.0 cm) for an electric cooking surface, a minimum of

30" (76.2 cm) for a gas cooking surface, and a suggested

maximum of 36" (91.4 cm) above the range to the bottom

of the hood. Mark a horizontal reference line on the wall.

3. Measure up from the horizontal mounting height reference

line 21

" (55.7 cm) and draw a parallel horizontal line.

Measure from the centerline 4

" (11.8 cm) in each direction

along the upper horizontal line. Mark the centers for the

fastener locations.

21¹⁵⁄₁₆" (55.7 cm)

4⁵⁄₈"

(11.8 cm)

4⁵⁄₈"

(11.8 cm)

A. Centerline

B. Fastener locations

C. Mounting height reference

(hood bottom line)

IMPORTANT: All screws must be installed into wall wooden

support structure. If there is no wooden support structure

to screw into, additional wall framing supports will be

required. This mounting structure must be capable of

supporting 100 lbs (45.4 kg).

4. Drill

" (4.8 mm) pilot holes at all locations where screws

are being installed into wood.

5. Using a TORX

T20

bit and driver, install the 2 - 8 x 80 mm

hanger bolts. Leave a 1

" (31.8 mm) gap between the wall

and the end of the hanger bolt for sliding the range hood into

place.

1¹⁄₄

(3.18 cm)

Vent Cover Bracket Installation

1. Use chimney cover mounting bracket centered on the

centerline of the wall and ﬂush to the ceiling to mark the

center points of the outermost holes for mounting screws.

Mark and drill 2 -

" (4.8 mm) holes.

2. Install the 5 mm wall anchors.

For Vented Installations Only:

1. Attach the chimney cover bracket to the wall using

2 - 5 x 40 mm screws (D).

A. Ceiling

B. Wall

C. Centerline

D. 5 x 40 mm screws (2)

For Non-Vented (recirculating) Installations Only:

1. Attach the chimney cover bracket and air deﬂector bracket

to the wall using the (2) 5 x 40 mm screws (D).

A. Ceiling

B. Wall

C. Centerline for range hood

2. Install the 5 x 40 mm screw through the top of the air

deﬂector bracket into the ceiling.

NOTE: To use the optional 5 mm wall anchor supplied with

the recirculation kit in the ceiling, locate and mark the hole

through the top of the air deﬂector bracket. Remove the

bracket and drill a

" (4.8 mm) hole and install the 5 mm

wall anchor.

A. Ceiling

B. Wall

Complete Preparation

1. Determine and make all necessary cuts in the wall for the

vent system. Install the vent system before installing the

hood. See the “Venting Requirements” section.

For Vented Installations Only:

■ Using a jigsaw or keyhole saw, cut a 6

" (16.5 cm) diameter

hole in the wall or ceiling for the vent duct.

■ Install the vent duct system through the hole.

Seal all connections with vent clamps.

For Use with Grounded Power Supply Cord:

■ This range hood is equipped with a power supply cord

having a 3 prong grounding plug.

■ A 3 prong receptacle is required to be located at a maximum

distance of 40" (101.6 cm) above the range hood terminal

box. If a mating outlet is not available, it is the responsibility

of the customer to have a properly grounded outlet installed

by a qualiﬁed electrician.

For Use with a Hard Wire Home Power Supply Cable:

■ Determine the required height for the home power supply

cable and drill a 1

" (3.2 cm) hole at this location.

■ Run the home power supply cable according to the National

Electrical Code or CSA Standards and local codes and

ordinances. There must be enough

" conduit and wires

from the fused disconnect (or circuit breaker) box to make

the connection in the hood’s electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

2. Use caulk to seal all openings.

D. 5 x 40 mm screws (2)

E. Air deﬂector bracket

F. Chimney cover bracket

C. Air deﬂector bracket

D. 5 x 40 mm screw

Install Range Hood

1. Using 2 or more people, hang range hood on the 2 mounting

screws through the mounting slots on the back of the hood.

A. Mounting hanger bolts

B. Mounting slots

C. Flat washers and nuts

2. Install the ﬂat washers and nuts to the hanger bolts. Level

the range hood and tighten the nuts.

Connect Vent System

For Vented Installations:

1. Assemble the damper (if needed) to the mounting boss using

(3) 3.5 x 9.5 mm screws.

2. Assemble the vent system to the damper (if used) or the

mounting boss.

A. Metal duct

B. Vent clamps

C. Mounting boss

3. Secure all of the connections with vent clamps.

4. Check that the backdraft damper (if used) works properly.

Front of range hood

Parallel

For Non-Vented (recirculating) Installations:

1. Mount the air deﬂector and ﬂexible duct assembly to the air

deﬂector bracket using (4) 3.5 x 9.5 mm screws supplied

with the Recirculation Kit.

A. Air deﬂector bracket

B. Air deﬂector/ﬂexible duct assembly

C. 3.5 x 9.5 mm screws (4)

2. Loosen the 4 nuts on the mounting boss. The back ﬂange of

each nut should be approximately

" (5 mm) from the face

of the mounting boss.

3. Expand the ﬂexible section of vent duct to the top of the

range hood top plate.

4. Check the mounting boss handle for alignment. The

mounting boss handle must align parallel with the front

of the range. If alignment is needed, loosen one of the

vent clamps and adjust as necessary. Retighten any vent

clamps that are loosened.

5. Secure all of the connections with vent clamps.

6. Reach inside the range hood cavity and grasp the handle

of the mounting boss. Pull down to align the nuts through

the cut-out holes in the module top cover. Push back into

the half-slots to assemble. Tighten the 4 nuts using the

" (13 mm) special tool or

" (13 mm) socket and driver

with extension.

A. Inside of range hood cavity

B. Mounting boss handle

C. Half slots in module top cover (4)

D. Nuts (4)

NOTE: For ceiling heights above 9 ft (1.8 m), an appropriate

length of 6" (15.2 cm) ducting (not supplied) will be required.

Reinstall Motor

1. Place the motor into the module housing, positioning it with

the large keyholes in motor mounting plate towards the back

of the canopy.

2. Grasping the motor plate, push the motor up into the module

housing. Locate the large keyholes over the motor mounting

nuts, push up against the module top cover, and pull the

motor forward to lock into the small keyholes slots.

3. Use the special

" (13 mm) tool and tighten the (4) nuts to

secure the motor.

Make Electrical Connection

For 3 Prong Grounded Power Cord:

1. Plug 3 prong power cord into a grounded 3 prong outlet

located above the range hood.

For Hard Wire from Home Power Supply:

1. Disconnect power.

2. Remove the terminal box cover.

3. Disconnect grounded power cord wires from terminal block.

Loosen the screws labeled “L,” “N,” and “Ground Symbol.”

4. Remove power cord strain relief from terminal box and

remove power cord.

A. Power cord

B. Power cord strain relief

C. Location “L” (black wire)

D. Location “N” (white wire)

E. Location ground symbol (green or bare ground wire)

5. Install a UL listed or CSA approved

" strain relief.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

40"

(101.6 cm)

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

A. Screws

B. Terminal box cover

6. Run the home power supply cable through the strain relief,

into the terminal box.

A. Home power supply cable

B. UL listed or CSA approved strain relief

C. Location “L” (black wire)

D. Location “N” (white wire)

E. Location ground symbol (green or bare ground wire)

7. Loosen the screw labeled “L” on the terminal block and

connect black wire C. Retighten the screw.

8. Loosen the screw labeled “N” on the terminal block and

connect white wire D. Retighten the screw.

9. Loosen the screw labeled with the “Ground Symbol” on the

terminal block and connect green (or bare) ground wire E.

Tighten the screw.

10. Tighten the strain relief screws.

11. Reinstall the terminal box cover.

12. Reconnect power.

Install Chimney Covers

1. On the upper chimney cover, bend out tabs (2) approximately

" (3 mm).

2. Slide rear ﬂanges of upper chimney cover between catch

tabs on chimney cover mounting bracket and lock bent-

out tabs into slots in the back plate of the chimney cover

mounting bracket.

NOTE: Once the upper chimney cover tabs are locked into

the chimney cover mounting bracket, the upper chimney

cover will be hard to remove. If removal is required, place a

thin blade behind the top corner of the upper chimney cover

and the chimney cover mounting bracket to push in the

catch tabs on both sides and pull the rear side ﬂange out

of the chimney cover mounting bracket.

3. Attach the (2) plastic spacers (F), one on each side at the

bottom of the blower module.

4. Widen the lower chimney cover and slide it over the upper

chimney cover and blower module. The lower chimney cover

must rest on the top of the hood.

A. Ceiling

B. Chimney cover mounting bracket

C. Upper chimney cover - rear ﬂanges

D. Upper chimney cover

E. Lower chimney cover

F. Plastic spacers (2)

WARNING

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire

in terminal box.

Failure to do so can result in death or electrical shock.

¹⁄₈"

(3 mm)

Complete Installation

1. For non-vented (recirculating) installations only, install the

charcoal ﬁlters over the metal mesh ﬁlter. See the “Range

Hood Care” section.

2. Install the metal ﬁlter. See the “Range Hood Care” section.

3. Check the operation of the range hood blower and lights.

See the “Range Hood Use” section.

NOTE: To get the most efﬁcient use from your new range

hood, read the “Range Hood Use” section.

The range hood is designed to remove smoke, cooking vapors,

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after

the cooking is complete to clear all smoke and odors from the

kitchen.

The range hood controls are located on the front of the canopy.

A. Louver holes (non-vented

[recirculating] installations only)

B. Chimney covers

C. Lamps

D. Filter door

E. Canopy

F. Control panel

Control Panel

RANGE HOOD USE

Controls and Features

NOTES:

■ To activate the controls, press and release the desired

button.

■ The control feature button will be lit when a control feature

is turned on.

Sleep Mode

The range hood automatically enters Sleep mode when not in

use. After 10 minutes of no range hood activity, all of the control

button lights will turn off. To deactivate Sleep mode, press any

button.

Auto Sense

Auto Sense allows the range hood fan to turn on automatically

when it senses heat higher than its allowable temperature limit.

When Auto Sense is ON, the fan speed will increase or decrease

based on the temperature Auto Sense is measuring.

Auto Sense can be manually increased by pressing a higher fan

speed. The fan will run at the selected speed for 10 minutes

before returning to the speed selected for Auto Sense.

If Auto Sense is ON, the Auto button light will turn off and go into

Sleep Mode when the vent hood is not in use. If the vent hood

is turned on by the consumer or by Auto Sense, the Auto button

light will turn on.

To set Auto Sense:

Press AUTO.

To Select Auto Sense Cooktop Type:

NOTE: The range hood is factory set for the gas cooktop

mode.

Press and hold AUTO for 5 seconds to switch between the

gas cooktop and electric cooktop modes.

The Auto button light will ﬂash 5 times when the range hood

is changed to the electric cooktop mode. Auto Sense is now

set to work with electric cooktops and ranges.

The Auto button light will ﬂash 3 times when the range hood

is changed to the gas cooktop mode. Auto Sense is now set

to work with gas cooktops and ranges.

Changing the cooktop type will change the temperature limit

for Auto Sense to turn on. When the range hood senses a

high enough temperature, the fan will start automatically.

When the temperature drops below the set temperature limit,

the fan will stop automatically. The Auto button light will turn

off after the range hood enters Sleep mode, but Auto Sense

is still active.

To Deactivate Auto Sense:

If the Auto button is lit, press AUTO once to deactivate

Auto Sense. The Auto button light will turn off.

If Auto Sense is in Sleep mode, press AUTO once to

deactivate Sleep mode and turn the Auto button light on.

Press AUTO again to deactivate Auto Sense and turn off

the Auto button light.

Auto Sense will automatically turn off after 2 hours of no

activation of the Auto Sense system. To reset Auto Sense,

press AUTO.

Manual Vent Functions

Auto Low

Med

Hi Boost Filter Light

Fan Speeds

Low

Press LOW to turn the fan on at Low speed.

Med

Press MED to turn the fan on at Medium speed.

Press HI to turn the fan on at High speed.

Boost

Press BOOST to turn the fan on at the

highest speed. Boost will automatically turn

off after 10 minutes and the fan will switch

to High speed.

Timer

The range hood can be set to automatically turn off after

15 minutes.

1. Press and hold the desired fan speed button for 2 seconds.

The fan will run on the chosen speed for 15 minutes and the

fan speed button light will ﬂash continuously.

After 15 minutes, the fan will turn off automatically.

2. Press the desired fan speed button again while the fan timer

is running to cancel the fan timer.

NOTE: Changing the fan speed or turning Auto Sense on will

also cancel the 15-minute timer.

Filter

The Filter button lights up when it is time to replace or clean the

ﬁlter. The button will be lit only when the fan is on. Press FILTER

after replacing the ﬁlter to turn the Filter button light off. See the

“Cleaning” section for how to replace or clean the ﬁlter.

Light

Press LIGHT to turn the range hood lights on and off.

RANGE HOOD CARE

Cleaning

IMPORTANT: Clean the hood and grease ﬁlters frequently

according to the following instructions. Replace grease ﬁlters

before operating hood.

Exterior Surfaces:

To avoid damage to the exterior surface, do not use steel wool

or soap-ﬁlled scouring pads.

Always wipe dry to avoid water marks.

Cleaning Method:

■ Liquid detergent soap and water, or all-purpose cleanser:

Wipe with damp soft cloth or nonabrasive sponge, then rinse

with clean water and wipe dry.

Metal Grease Filters

The ﬁlter should be washed frequently. Place the metal ﬁlter in

the dishwasher or hot detergent solution to clean.

Let the ﬁlter dry thoroughly before replacing it.

NOTE: The metal grease ﬁlter is located behind the center metal

ﬁlter cover. The panel is magnetically secured along the front

and has a tab along the back to hold the ﬁlter cover in place. To

access the grease ﬁlter, grasp the panel on the front corners and

pull down. This releases the panel from the magnets and allows

the panel to swing down. Pull the alignment tab on the ﬁlter

cover out of the alignment slot on the range to remove.

A. Slot for ﬁlter cover alignment

B. Filter cover magnets

C. Filter cover

D. Tab on ﬁlter cover for alignment

To Remove Metal Grease Filters:

1. Turn off fan and lights.

2. Remove the ﬁlter holder frame and grease ﬁlter using a ﬂat-

blade screwdriver to turn the grease ﬁlter release screws 90°

counterclockwise.

A. Grease ﬁlter release screw

B. Filter holder frame

C. Grease ﬁlter

To Replace Metal Grease Filter:

Replace grease ﬁlter and ﬁlter holder frame into range hood.

Align the grease ﬁlter release screw and use a ﬂat-blade

screwdriver to turn the grease ﬁlter release screws 90°

clockwise to lock in place.

Charcoal Filters - For Non-Vented (recirculating)

Installations

NOTE: After approximately 3 years of use the charcoal ﬁlter

should be replaced. To order a replacement Charcoal Filter Kit,

see the “Assistance or Service” section.

The charcoal ﬁlters can be cleaned and reactivated. Clean the

ﬁlter in the dishwasher using normal detergent and choosing the

highest temperature setting.

To reactivate the ﬁlter, the ﬁlter should be dried in an oven for

10 minutes with a maximum temperature of 210°F (100°C).

To Remove Charcoal Filters:

1. Turn fan and lights off.

2. Remove the metal grease ﬁlters. See the “Metal Grease

Filters” section.

3. Remove the upper and side lock springs.

4. Clean or discard the charcoal ﬁlter.

To Replace Charcoal Filters:

1. For non-vented (recirculating installations), install charcoal

ﬁlter, wrapping it around the grease ﬁlter.

2. Place the charcoal ﬁlter mat around the grease ﬁlter and ﬁx it

in place by using the cap lock springs provided.

3. Position the upper cap and ﬁx it in place using the cap lock

spring provided.

A. Charcoal ﬁlter mat

B. Grease ﬁlter

C. Charcoal ﬁlter side lock springs

D. Upper cap

E. Cap lock spring

F. Grease ﬁlter support

WIRING DIAGRAM

SEL0093237

4 23

66 6 6

Power

Connections

Additional lamp only

in 4 lamps version

Fuse

RL2

RL4

RL1

FT1

FT2

FT6 FT4

FT5FT3

BK - 1

YL/

WH - 2

BK - 3

WH -

BU - 5

RD - 4

GY - 3

Motor Specifications

3.7 A

120 VAC

Blue - Red

Blue - Black

Frequency

Power Supply

Wattage Rating

14.90 Ohm

9.92 Ohm

22.00 Ohm

Amperage

Motor Speed/Resistance

18.40 Ohm

420 W

Blue - Gray

60 Hz

Blue - White

Component Layout

Description

Num.

E.M.I. Filter

User Interface

Main Board

Light Driver

Capacitor

LED Lamp

Temperature Sensor

Surge Protector

Motor

YL/

2 Speed

4 Speed

3 Speed

1 Speed

120 VAC

Not

used

Not

used

12 VDC

12 VDC12 VDC

12 VDC

VDC

ASSISTANCE OR SERVICE

If you need service:

Please refer to the warranty page in this manual.

If you need replacement parts:

If you need to order replacement parts, we recommend that

you use only factory speciﬁed parts. Factory speciﬁed parts

will ﬁt right and work right because they are made with the

same precision used to build every new appliance.

To locate factory speciﬁed replacement parts in your area, call

the following customer assistance telephone number or your

nearest designated service center.

In the U.S.A.

Call Jenn-Air Customer eXperience Center toll free:

1-800-JENNAIR (1-800-536-6247) or visit our website

at www.jennair.com.

Our consultants provide assistance with:

■ Scheduling of service. Jenn-Air

appliances designated

service technicians are trained to fulﬁll the product

warranty and provide after-warranty service anywhere

in the United States.

■ Features and speciﬁcations on our full line of appliances.

■ Referrals to local Jenn-Air

appliance dealers.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

For further assistance:

If you need further assistance, you can write to Jenn-Air

Appliances with any questions or concerns at:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

In Canada

Call the Whirlpool Canada LP Customer eXperience Centre toll

free at 1-800-JENNAIR (1-800-536-6247) or visit our website at

www.jennair.ca.

Our consultants provide assistance with:

■ Scheduling of service. Jenn-Air

appliances designated

service technicians are trained to fulﬁll the product warranty

and provide after-warranty service anywhere in Canada.

■ Features and speciﬁcations on our full line of appliances.

■ Referrals to local Jenn-Air

appliance dealers.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

For further assistance:

If you need further assistance, you can write to Jenn-Air

Appliances with any questions or concerns at:

Jenn-Air Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Accessories

Charcoal Filter Kit

(for non-vented installations only)

Order Part Number W10272069

Chimney Extension Kit (vented)

(for 9' 6" to 12' [2.89 m to 3.66 m] ceilings)

Order Part Number W10646864

Chimney Kit Recirculation

(for 7' 9" to 10' 4" [2.36 m to 3.15 m] ceilings)

(for non-vented installations)

Order Part Number W10685949

Chimney Extension Kit (recirculating)

(for 9' 6" to 12' [2.89 m to 3.66 m] ceilings)

(for non-vented installations)

Order Part Number W10686362

6" (15.2 cm) Makeup Air Kit

(consult local building codes)

Order Part Number W10446915

Vent Duct Adapter 6" to 8" (15.2 cm to 20.3 cm)

(for 8" [20.3 cm] duct installations)

Order Part Number W10685950

12/14

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair. Some

questions can be addressed without service. Please take a few minutes to review the Troubleshooting or

Problem Solver section of the Use and Care Guide, scan the QR code on the right to access additional

resources, or visit

https://jennair.custhelp.com.

2. All warranty service is provided exclusively by our authorized Jenn-Air Service Providers. In the U.S. and

Canada, direct all requests for warranty service to:

Jenn-Air Customer eXperience Center

1-800-JENNAIR (1-800-536-6247).

If outside the 50 United States or Canada, contact your authorized Jenn-Air dealer to determine whether another warranty applies.

JENN-AIR®

MAJOR APPLIANCE

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED

TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

■ Name, address and telephone number

■ Model number and serial number

■ A clear, detailed description of the problem

■ Proof of purchase including dealer or retailer name and address

TWO YEAR LIMITED WARRANTY

WHAT IS COVERED WHAT IS NOT COVERED

For two years from the date of

purchase, when this major appliance

is installed, operated and maintained

according to instructions attached to

or furnished with the product, Jenn-

Air brand of Whirlpool Corporation or

Whirlpool Canada LP (hereafter “Jenn-

Air”) will pay for Factory Speciﬁed

Replacement Parts and repair labor

to correct defects in materials or

workmanship that existed when this

major appliance was purchased, or at

its sole discretion replace the product.

In the event of product replacement,

your appliance will be warranted for

the remaining term of the original unit’s

warranty period.

YOUR SOLE AND EXCLUSIVE

REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE PRODUCT

REPAIR AS PROVIDED HEREIN.

Service must be provided by a Jenn-

Air designated service company. This

limited warranty is valid only in the

United States or Canada and applies

only when the major appliance is

used in the country in which it was

purchased. This limited warranty is

effective from the date of original

consumer purchase. Proof of original

purchase date is required to obtain

service under this limited warranty.

1. Commercial, non-residential, multiple-family use, or use inconsistent with published user,

operator or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation, installation not in accordance

with electrical or plumbing codes or correction of household electrical or plumbing (i.e. house

wiring, fuses or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water ﬁlters, preservation solutions, etc.).

5. Defects or damage caused by the use of non-genuine Jenn-Air parts or accessories.

6. Conversion of products from natural gas or L.P. gas.

7. Damage from accident, misuse, abuse, ﬁre, ﬂoods, acts of God or use with products not

approved by Jenn-Air.

8. Repairs to parts or systems to correct product damage or defects caused by unauthorized

service, alteration or modiﬁcation of the appliance.

9. Cosmetic damage including scratches, dents, chips, and other damage to the appliance

ﬁnishes unless such damage results from defects in materials and workmanship and is

reported to Jenn-Air within 30 days.

10. Discoloration, rust or oxidation of surfaces resulting from caustic or corrosive environments

including but not limited to high salt concentrations, high moisture or humidity or exposure to

chemicals.

11. Food or medicine loss due to product failure.

12. Pick-up or delivery. This product is intended for in-home repair.

13. Travel or transportation expenses for service in remote locations where an authorized Jenn-Air

servicer is not available.

14. Removal or reinstallation of inaccessible appliances or built-in ﬁxtures (i.e. trim, decorative

panels, ﬂooring, cabinetry, islands, countertops, drywall, etc.) that interfere with servicing,

removal or replacement of the product.

15. Service or parts for appliances with original model/serial numbers removed, altered or not

easily determined.

The cost of repair or replacement under these excluded circumstances shall be borne by

the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not

allow limitations on the duration of implied warranties of merchantability or ﬁtness, so this limitation may not apply to you. This warranty gives

you speciﬁc legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Jenn-Air makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this

major appliance, you should ask Jenn-Air or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. JENN-

AIR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or

limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you speciﬁc

legal rights, and you also may have other rights that vary from state to state or province to province.

https://jennair.custhelp.com

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

Avertissements de la proposition 65 de l'État de Californie :

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par l’État de Californie pour être à l’origine de

cancers.

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par l’État de Californie pour être à l’origine de

malformations et autres déficiences de naissance.

La page est en cours de chargement...

JennAir JXW8936DS Manuel utilisateur

Marque: JennAir

Modèle: JXW8936DS

Catégorie: Hottes

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: JennAir JXW8936DS User manual

JennAir JXW8936DS Manuel utilisateur

Ce manuel convient également à

JennAir JXW8936DS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents