Mitsubishi Electric RD77MS Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
RD77-U-HW
Before Using the Product
Please read this document before use. Keep this for future reference and make sure that end
users will read this.
Related manuals
Before using the product, please read the manuals that are supplied with the base unit and the
servo amplifier.
Confirm the following descriptions:
●SAFETY PRECAUTIONS
●CONDITIONS OF USE FOR THE PRODUCT
●EMC AND LOW VOLTAGE DIRECTIVES
●WARRANTY
Details of the product are also described in the manual shown below (sold separately).
Please read the manual and understand the functions and performance of the product to use it
correctly.
• MELSEC iQ-R Simple Motion Module User's Manual (Startup)
IB-0300245
• MELSEC iQ-R Simple Motion Module User's Manual (Application)
IB-0300247
• MELSEC iQ-R Simple Motion Module User's Manual (Advanced Synchronous Control)
IB-0300249
Manuels correspondants
Avant d'utiliser le produit, prendre la peine de lire les manuels fournis avec l'unité de base et le
servo-amplificateur.
Revoir les points suivants :
●PRÉCAUTIONS DE SÉCURITÉ
●CONDITIONS D'UTILISATION DE PRODUIT
●DIRECTIVES EMC ET BASSE TENSION
●GARANTIE
Packing list
Check that the following items are included in the package.
Signal layout for external input connection connector
Affectation des signaux au connecteur de raccordement d'entrée
externe
RD77MS2 does not have 2A20 to 2A1 terminals and 2B20 to 2B1 terminals.
*1 The 2A(B)20 to 2A(B)8 terminals are "No connect", 2A5 to 2A1 are "SIN15 to SIN11", and 2B5 to 2B1 are
"SIN20 to SIN16".
*2 Input type from manual pulse generator/incremental synchronous encoder is switched in "[Pr.89] Manual pulse
generator/Incremental synchronous encoder input type selection". (Only the value specified against the axis 1
is valid.)
0: Differential-output type
1: Voltage-output/open-collector type (Default value)
*3 Set the signal input form in "[Pr.24] Manual pulse generator/Incremental synchronous encoder input selection".
*4 Voltage-output/open-collector type of manual pulse generator/incremental synchronous encoder:
Connect the A-phase/PULSE signal to HA, and the B-phase/SIGN signal to HB.
*5 Differential-output type of manual pulse generator/incremental synchronous encoder:
Connect the A-phase/PULSE signal to HAH, and the A-phase/PULSE inverse signal to HAL.
Connect the B-phase/SIGN signal to HBH, and the B-phase/SIGN inverse signal to HBL.
*6 Do not connect to any terminals explained as "No connect".
*7 Set the external command signal [DI, FLS, RLS, DOG, STOP] in "[Pr.116] FLS signal selection","[Pr.117] RLS
signal selection", "[Pr.118] DOG signal selection", "[Pr.119] STOP signal selection" and "[Pr.95] External
command signal selection".
*8 Do not use 1A20, 1A19, 1A(B)15 and 1A(B)14 for other than the power supply of manual pulse generator.
The table below shows applicable external input wiring connector. When wiring, use applicable
wires.
Le tableau ci-dessous indique quels connecteurs on peut utiliser comme connecteur de câblage
des entrées externes. Pour le câblage, utiliser les fils prescrits.
Operating ambient temperature
Use the product within the following range.
• 0 to 55 (when an extended temperature range base unit is not used)
• 0 to 60 (when an extended temperature range base unit is used)
Température ambiante de fonctionnement
Ce produit doit être utilisé dans les conditions suivantes.
•0 et 55
(quand une unité de base à gamme de température élargie n'est pas utilisée)
•0 et 60
(quand une unité de base à gamme de température élargie est utilisée)
BCN-B62008-335-D(1806)MEE
RD77MS2 RD77MS4 RD77MS8 RD77MS16 RD77MS16-AP020
Item Quantity
Module 1
"Before Using the Product" (this document) 1
Pin
number
Signal name Pin
number
Signal name
1B20 Manual pulse
generator/Incremental
synchronous encoder B-
phase/SIGN (HB)
*2*3*4
1A20 Manual pulse generator
power supply output
(+5VDC) (5V)
*8
1B19 Manual pulse
generator/Incremental
synchronous encoder A-
phase/PULSE (HA)
*2*3*4
1A19 Manual pulse generator
power supply output
(+5VDC) (5V)
*8
1B18 Manual pulse
generator/Incremental
synchronous encoder B-
phase/SIGN (HBL)
*2*3*5
1A18 Manual pulse
generator/Incremental
synchronous encoder B-
phase/SIGN (HBH)
*2*3*5
1B17 Manual pulse
generator/Incremental
synchronous encoder A-
phase/PULSE (HAL)
*2*3*5
1A17
Manual pulse
generator/Incremental
synchronous encoder A-
phase/PULSE (HAH)
*2*3*5
1B16 No connect
*6
1A16 No connect
*6
1B15 Manual pulse generator
power supply output
(+5VDC) (5V)
*8
1A15 Manual pulse generator
power supply output
(+5VDC) (5V)
*8
1B14 Manual pulse generator
power supply output
(GND) (SG)
*8
1A14 Manual pulse generator
power supply output
(GND) (SG)
*8
1B13 No connect
*6
1A13 No connect
*6
1B12 1A12
1B11 1A11
1B10 1A10
1B9 1A9
1B8 Forced stop input signal
common (EMI.COM)
1A8 Forced stop input signal
(EMI)
1B7 Common (COM) 1A7 Common (COM)
1B6 Common (COM) 1A6 Common (COM)
1B5 Input signal (SIN10)
*7
1A5 Input signal (SIN5)
*7
1B4 Input signal (SIN9)
*7
1A4 Input signal (SIN4)
*7
1B3 Input signal (SIN8)
*7
1A3 Input signal (SIN3)
*7
1B2 Input signal (SIN7)
*7
1A2 Input signal (SIN2)
*7
1B1 Input signal (SIN6)
*7
1A1 Input signal (SIN1)
*7
2B20
*1 *1
2B19
2B18
2B17
2B16
2B15
2B14
2B13
2B12
2B11
2B10
2B9
2B8
2B7
2B6
2B5
2B4
2B3
2B2
2B1
2A20
2A19
2A18
2A17
2A16
2A15
2A14
2A13
2A12
2A11
2A10
2A9
2A8
2A7
2A6
2A5
2A4
2A3
2A2
2A1
1B20
1B19
1B18
1B17
1B16
1B15
1B14
1B13
1B12
1B11
1B10
1B9
1B8
1B7
1B6
1B5
1B4
1B3
1B2
1B1
1A20
1A19
1A18
1A17
1A16
1A15
1A14
1A13
1A12
1A11
1A10
1A9
1A8
1A7
1A6
1A5
1A4
1A3
1A2
1A1
Front view of the module
External input connection
connector
(module side)
English French English French
Signal name Nom de signal Manual pulse generator
power supply output
(+5VDC)
Sortie alimentation
générateur d'impulsions
manuel (+5VDC)
Pin number Broche N° Manual pulse generator
power supply output
(GND)
Sortie alimentation
générateur d'impulsions
manuel (GND)
External input connection
connector (module side)
Connecteur de
raccordement d'entrée
externe (côté module)
Forced stop input signal
common
Signal d'entrée d'arrêt
forcé Commun
Front view of the module Vue de l'avant du module Common Commun
Manual pulse
generator/Incremental
synchronous encoder *-
phase/SIGN
Générateur d'impulsions
manuel/Encodeur synchrone
incrémentiel Phase */SIGN
Input signal Signal d'entrée
Manual pulse
generator/Incremental
synchronous encoder *-
phase/PULSE
Générateur d'impulsions
manuel/Encodeur synchrone
incrémentiel Phase */PULSE
Forced stop input signal Signal d'entrée d'arrêt
forcé
No connect Non connecté
English French
RD77MS2 does not have 2A20 to 2A1 terminals and
2B20 to 2B1 terminals.
Les bornes 2A20 à 2A1 et 2B20 à 2B1 n'existent pas sur
le RD77MS2.
The 2A(B)20 to 2A(B)8 terminals are "No connect",
2A5 to 2A1 are "SIN15 to SIN11", and 2B5 to 2B1 are
"SIN20 to SIN16".
Les bornes 2A(B)20 à 2A(B)8 sont "Non connecté", 2A5 à
2A1 sont "SIN15 à SIN11", et 2B5 à 2B1 sont "SIN20 à
SIN16".
Input type from manual pulse generator/incremental
synchronous encoder is switched in "[Pr.89] Manual
pulse generator/Incremental synchronous encoder
input type selection". (Only the value specified against
the axis 1 is valid.)
• 0: Differential-output type
• 1: Voltage-output/open-collector type (Default value)
Le type d'entrée en provenance du générateur
d'impulsions manuel/encodeur synchrone incrémentiel
permute en "[Pr.89] Manual pulse generator/Incremental
synchronous encoder input type selection". (Seule la
valeur spécifiée pour axe 1 est valide.)
• 0: Type différentiel-sortie
• 1: Type tension-sortie/ouvert-collecteur (valeur par
défaut)
Set the signal input form in "[Pr.24] Manual pulse
generator/Incremental synchronous encoder input
selection".
Adopter une forme d'entrée de signal dans "[Pr.24]
Manual pulse generator/Incremental synchronous
encoder input selection".
Voltage-output/open-collector type of manual pulse
generator/incremental synchronous encoder:
Connect the A-phase/PULSE signal to HA, and the B-
phase/SIGN signal to HB.
Type tension-sortie/ouvert-collecteur du générateur
d'impulsions manuel/encodeur synchrone incrémentiel:
Raccorder le signal Phase A/PULSE sur HA, et le signal
Phase B/SIGN sur HB.
Differential-output type of manual pulse
generator/incremental synchronous encoder:
Connect the A-phase/PULSE signal to HAH, and the
A-phase/PULSE inverse signal to HAL.
Connect the B-phase/SIGN signal to HBH, and the B-
phase/SIGN inverse signal to HBL.
Type différentiel-sortie du générateur d'impulsions
manuel/encodeur synchrone incrémentiel:
Raccorder le signal Phase A/PULSE sur HAH, et le signal
Phase A/PULSE inversé sur HAL.
Raccorder le signal Phase B/SIGN sur HBH, et le signal
Phase B/SIGN inversé sur HBL.
Do not connect to any terminals explained as "No
connect".
Ne rien raccorder à aucune des bornes portant la mention
"Non connecté".
Set the external command signal [DI, FLS, RLS, DOG,
STOP] in "[Pr.116] FLS signal selection","[Pr.117] RLS
signal selection", "[Pr.118] DOG signal selection",
"[Pr.119] STOP signal selection" and "[Pr.95] External
command signal selection".
Régler le signal de commande externe [DI, FLS, RLS,
DOG, STOP] dans "[Pr.116] FLS signal
selection","[Pr.117] RLS signal selection", "[Pr.118] DOG
signal selection", "[Pr.119] STOP signal selection"et
"[Pr.95] External command signal selection".
Do not use 1A20, 1A19, 1A(B)15 and 1A(B)14 for
other than the power supply of manual pulse
generator.
Ne pas utiliser 1A20, 1A19, 1A(B)15 et 1A(B)14 dans un
but autre que l'alimentation du générateur d'impulsions
manuel.
External input wiring connector Wire
Model Tightening torque Diameter Type Material Temperature rating
A6CON1 0.20 to 0.29 Nm AWG22 Stranded Copper 75 or more
A6CON2 AWG24
A6CON4 AWG22
Connecteur de câblage des entrées
externes
Fil
Modèle Couple de serrage Diamètre Type Matériau Gamme de
température
A6CON1 0,20 à 0,29 Nm AWG22 Torsadé Cuivre 75
ou plus
A6CON2 AWG24
A6CON4 AWG22
-
1
Mitsubishi Electric RD77MS Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
Documents connexes
-
Mitsubishi Electric RD77GF Le manuel du propriétaire
-
-
-
-
-
-
-
-
-