Blue Sea Systems 7531 Manuel utilisateur

Marque: Blue Sea Systems

Modèle: 7531

Catégorie: Chargeurs de batterie

Taper: Manuel utilisateur

Ce manuel convient également à

P12

User Manual

7531 and 7532

BATTERY CHARGER

Read and understand the contents of this User Manual. It contains important safety, handling, and operational instructions for P12 Battery Chargers.

This User Manual describes the product mentioned herein at the time of its publication. Speciﬁcations and performance are subject to change at the discretion

of Blue Sea Systems. To view the most current revision of this publication visit bluesea.com/P12.

Scan for

additional

product

information

Table of Contents

Important Safety Instructions 1–2

P12 Battery Charger Overview 3–4

Speciﬁcations 5

Installation Tables 5

• Table A: Minimum Recommended Wire Size

• Table B: Recommended DC Circuit Protection

• Table C: Typical AC Regional Wire Colors

• Table D: AC Wire - Circuit Protection Selection Chart

• Table E: Default Voltages by Battery Type

Product Dimensions and Installation Clearances 6

Included Components 7

Supplies Needed 8

Installation Instructions 9–10

Initial Charger Setup 11

Advanced Charger Setup 12–13

Reset to Manufacturer Defaults 13

Absorption Parameters and Timers, Energy Save Feature Control 14–15

Temperature Parameters 15

Equalization 16–17

Screen Summary 18–19

Alert Screens and Diagnostics 20–21

Optional Installation 22–23

• Automatic Charging Relays (ACRs)

Warranty and Contact Information 24

P12 Charge Management System 25

P12

7531 AND 7532 BATTERY CHARGERS

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

WARNING

Refers to a potentially hazardous situation which, if not avoided, could result in death or serious injury.

The P12 Battery Charger should be installed by a qualiﬁed marine electrician. Improper installation can result in electrical shock which may cause serious

injury or death. To reduce the risk of electrical shock, mount vertically in a dry, well ventilated location. Charge these battery types: Flooded, AGM, Gel, or

TPPL Lead Acid batteries. Consult battery manufacturer speciﬁcations for other battery types to avoid damage. This battery charger is not intended for use

by persons (including children) with lack of ability, experience, or knowledge, unless they have been given supervision or instruction concerning use of the

battery charger by a person responsible for their safety. Do not recharge non-rechargeable batteries. Children should be supervised to ensure that they do

not play with the appliance. Avoid serious injury or death from electrical shock, turn off AC supply power before opening terminations cover.

Risk of Explosive Gases

Working in the vicinity of a Lead-Acid battery is dangerous. Batteries generate explosive gases during normal battery operation. Explosive gasses can ignite

and may cause serious injury or death. Ensure battery location is properly ventilated according to battery manufacturer or industry standards. To reduce risk

of battery explosion, follow these instructions and those published by the battery manufacturer. Do not smoke or cause a spark in the area around batteries

and engines. Each time before using your charger read this manual and follow the instructions. Do not use any accessory devices that directly connect to

the charger other than those manufactured by Blue Sea Systems and designed for use with the P12 Battery Charger. Do not operate the charger if it has

been dropped or damaged. Contact Blue Sea Systems on how to proceed. Wear complete eye protection and protective clothing when dealing with lead

acid batteries. Remove personal metal items such as jewelry & rings when working around batteries.

CAUTION

Refers to a potentially hazardous situation which, if not avoided, may result in injury.

Before beginning electrical installation, read the instruction manual. Disconnect all AC and DC power sources. Do not make ﬁnal connections to the

batteries until DC connections on the charger are made and veriﬁed. Do not make or break electrical connections to batteries while charging or for up to

30 minutes after charging. Other than parts accessed under the termination cover, there are no user serviceable parts within the battery charger enclosure.

Contact Blue Sea Systems for servicing. Charge only user selectable type batteries, other types of batteries may burst causing personal injury and damage.

Do not use the battery charger to charge dry cell batteries that are commonly used with home appliance. These batteries may burst and cause injury to

person and damage to property. Never charge a frozen battery.

GROUNDING PRECAUTIONS

Marine battery chargers and inverters have two grounding connections, one from the AC system and one from the DC system. ABYC requires

the AC grounding system to be connected to the DC grounding system through the distribution systems. Additionally, the chargers make

connections to both systems. It is very important the systems be connected properly before the charger is installed. Otherwise the charger

grounding system may become the sole connection between AC and DC ground and it may not be sized large enough to provide system wide

safety function. The AC grounding conductor is the conductor with green, or green with yellow stripe included in the AC power cable and should

be sized the same as the power and neutral conductors (see Table C page 5 for AC wire color). This will connect to the right most terminal in

the AC connection block. There is also chassis connection terminal for a DC safety grounding wire. The DC safety ground should be green or

marked green and sized equal to, or one wire size smaller, than the DC charge wires.

READ AND SAVE THESE INSTRUCTIONS

1. SAVE THESE INSTRUCTIONS – This manual contains important safety and operating instructions for battery charger Models 7531 and 7532.

2. Do not expose charger to rain or snow.

3. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of ﬁre, electric shock, or injury to persons.

4. Do not operate charger with damaged cord – replace the cord immediately.

5. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualiﬁed serviceman.

6. Do not disassemble charger; take it to a qualiﬁed serviceman when service or repair is required. Incorrect reassembly may result in a risk of

electric shock or ﬁre. The battery charger must be properly assembled in accordance with the assembly instruction before it is used.

7. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk.

WARNING – RISK OF EXPLOSIVE GASES.

a) WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING

NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS

EACH TIME YOU USE THE CHARGER.

b) To reduce risk of battery explosion, follow these instructions and those published by battery manufacturer and manufacturer of any equipment you

intend to use in vicinity of battery. Review cautionary marking on these products and on engine.

PERSONAL PRECAUTIONS

a) Consider having someone close enough by to come to your aid when you work near a lead-acid battery.

b) Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.

c) Wear complete eye protection and clothing protection. Avoid touching eyes while working near battery.

d) If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters eye, immediately ﬂood eye with running cold water for at

least 10 minutes and get medical attention immediately.

IMPORTANT SAFETY INSTRUCTIONS

P12

7531 AND 7532 BATTERY CHARGERS

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

IMPORTANT SAFETY INSTRUCTIONS

Warnings

Specifications

Terminations

Display

P12

7531 AND 7532 BATTERY CHARGERS

Regulatory

e) NEVER smoke or allow a spark or ﬂame in vicinity of battery or engine.

f) Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark or short-circuit battery or other electrical part that

may cause explosion.

g) Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead-acid battery. A lead-acid battery can produce a

short-circuit current high enough to weld a ring or the like to metal, causing a severe burn.

h) Use charger for charging a LEAD-ACID battery only. It is not intended to supply power to a low voltage electrical system other than in a starter-motor

application. Do not use battery charger for charging dry-cell batteries that are commonly used with home appliances. These batteries may burst and

cause injury to persons and damage to property.

i) NEVER charge a frozen battery.

10.

PREPARING TO CHARGE

a) If necessary to remove battery from vessel to charge, always remove grounded terminal from battery ﬁrst. Make sure all accessories in the vehicle are

off, so as not to cause an arc.

b) Be sure area around battery is well ventilated while battery is being charged.

c) Clean battery terminals. Be careful to keep corrosion from coming in contact with eyes.

d) Add distilled water in each cell until battery acid reaches level speciﬁed by battery manufacturer. Do not overﬁll. For a battery without removable cell

caps, such as valve regulated lead acid batteries, carefully follow manufacturer’s recharging instructions.

e) Study all battery manufacturer’s speciﬁc precautions while charging and recommended rates of charge.

f) Determine voltage of battery by referring to vessel owner’s manual and make sure it matches output rating of battery charger.

11.

CHARGER LOCATION

a) Locate charger as far away from battery as DC cables permit.

b) Never place charger directly above battery being charged; gases from battery will corrode and damage charger.

c) Never allow battery acid to drip on charger when reading electrolyte speciﬁc gravity or ﬁlling battery.

d) Do not operate charger in a closed-in area or restrict ventilation in any way.

e) Do not set a battery on top of charger.

GROUNDING INSTRUCTIONS – This battery charger should be connected to a grounded, metal, permanent wiring system; or an equipment-grounding

conductor should be run with circuit conductors and connected to equipment-grounding terminal or lead on battery charger. Connections to battery charger

should comply with all local codes and ordinances.

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

The Blue Sea Systems P12 Battery Charger is dry mount device designed for use in marine applications and other harsh environments where

reliability, ease of use, and high performance are of primary importance. The P12 is designed in Bellingham, Washington, USA.

The P12 is designed to charge three electrically independent batteries or battery banks. The P12 has the unique capability to individually move each battery out of the

Absorption charging stage. This ensures batteries near their full charge do not continue to receive high constant voltages necessary in the Absorption stage. This is optimal

treatment for long battery life. Charge Coordination integrates with the Blue Sea Systems family of Automatic Charging Relays (ACR) to force separation of the battery banks

while the P12 is operational, to allow the batteries to individually exit the absorption stage. After fourteen days of continuous Float, the charger will repeat the normal charge

cycle to assure good battery health.

For reliability, the P12 has a rugged cast aluminum housing with high heat dissipating capability for minimum cooling fan run times. The electronic design has given special

consideration to operation in areas of inconsistent AC power quality. The P12 has a Power Factor Corrected nominal AC input range of 115V to 230V AC within which it will

produce its full rated DC charging output. It will continue to produce reduced DC output to as low as 75V AC. After a shut down below 75V AC or when there is interrupted

switching between AC sources, like switching between generator and shore power, the P12 will automatically perform an orderly restart.

Central to the P12’s ease of use is the large plain-language full graphics control screen capable of displaying in French, English, Italian, German and Spanish. The plain

language display enables clear communication with the operator for setting precise charging parameters and providing a broad range of easily understood fault

communications and operating history. An optional remote display brings much of this functionality to a secondary location away from the charger.

The P12 contains charge proﬁles for most batteries available today, including Flooded Lead Acid (FLA), Gel, Thin Plate Pure Lead (TPPL), and Absorbed Glass Mat (AGM).

In addition, a user conﬁgurable charge proﬁle is available for other battery types.

The P12 has built-in safety features including: ignition protection, over and under temperature protection (sensed internally and at the batteries), DC reverse polarity

protection, DC over voltage protection, surge, and short circuit protection.

The deﬁnitions of the P12 charging stages are deﬁned below. The charging stage LEDs on the front of the charger will indicate the current stage.

Absorption (Constant voltage)

In the Absorption charging stage the batteries complete their charging by being “topped off”. This is a less aggressive charging stage than Bulk where the current going into a

particular battery bank will signiﬁcantly reduce with time. The conditions for a battery bank to be considered “full” vary based on many different factors. In order for a battery

bank to leave the Absorption stage a number of different parameters must be met. The main parameters are the Absorption Timers which can be seen on

page 14. Outputs move individually from Absorption to Pre-Float. When all batteries have completed Absorption, the charger will move them into the Float stage.

Float* (Constant voltage)

Float is the ﬁnal charging stage for fully charged batteries. Batteries in this stage are being maintained at their deﬁned ﬂoat voltage. Typically Float voltage

has a 1.0V or greater difference from the Absorption voltage.

Pre-Float (Constant voltage)

The Pre-Float charging stage is unique to the P12. Since the size of battery banks typically vary from one output to the next, there is a need to charge each bank independently.

Once all batteries are in Absorption, battery banks may ﬁnish charging at different rates. Once a battery bank has met its unique Absorption parameters, the P12 Charger will

independently move it into the Pre-Float stage. Pre-Float is the initial stage to maintain a fully charged battery. Batteries in Pre-Float can have up to a .5V difference

between batteries in Absorption. Up to two outputs can be in Pre-Float simultaneously.

Bulk (Constant current)

The Bulk charging stage is the ﬁrst stage in the battery charging process. It is where a majority of the charging actually takes place leaving batteries at approximately

75% to 80% of their ﬁnal capacity. The goal of the Bulk stage is to drive current into the batteries quickly to increase their voltage. Once all the batteries have reached the

deﬁned Absorption voltage, the charger will move them into the Absorption stage.

14.5V

14.0V

T I M E

Absorption

PreFloat

Bulk

13.5V

Battery 1

Battery 2

Battery 3

PreFloat

Float

Example of Flooded Lead Acid Battery

14.5V

T I M E

Absorption

Bulk

13.5V

Battery 1

Battery 2

Battery 3

Float

Forced Absorption: A period when batteries are potentially over charged.

Example of Flooded Lead Acid Battery

Absorption

Forced Absorption

Conventional Three Stage Battery ChargingFour Stage Battery Charging

Four Stage Battery Charging

P12 Battery Charger Overview

P12

7531 AND 7532 BATTERY CHARGERS

*Energy Saver Mode (CEC)

a) After the absorption cycle is completed for all outputs, the charger moves to “rest” mode – not ﬂoat.

b) As the battery(s) rests, the voltage will drop. If loads are active, the voltage will drop more rapidly.

c) When the voltage has dropped to the lower target re-ﬂoat voltage, the charger will re-start and attempt to enter ﬂoat mode for a minimum of 4 hours.

d) The charger will enter rest mode again and the cycle will repeat.

NOTE: The CEC test is performed on batteries that have no active loads.

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

Rugged, finned

cast aluminum case

Fan vent

Screen selection

buttons

Charging stage

indicators

Termination

cover latches

Charging and

Alert indicators

Graphic LCD Display

Termination

insulating

cover

DC output

DC strain

relief clamp

AC strain

relief and

insulating cover.

AC input terminals

under cover.

Mounting holes

Clearance for:

M6, 1/4", or #12

mounting hardware

NOTE: Mounting holes screw

centers are not symmetrical.

Please see dimension drawing

on page 6

P12 Battery Charger Overview

P12

7531 AND 7532 BATTERY CHARGERS

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

Specifications

* Consult battery manufacturer speciﬁcations for other battery types to avoid damage. Do not mix battery types.

** Battery bank sizes are tested to California Energy Commission compliance (CEC). Larger and smaller size banks could charge well, but consume slightly

more power over the charging cycle.

Regulatory

Designed and constructed for compliance to UL-1236 Marine, CSA 22.2 No. 107.2, and ABYC A-31 standards.

CE Marked

Ignition Protection per ISO 8846 and SAE J1171. Meets FCC Part 15, Class B requirements. To view all regulatory speciﬁcations visit www.bluesea.com/P12.

California Energy Commission (CEC) compliant. The energy saving feature may be disabled by the user following the steps on page 14 of this manual.

7531 7532

Total Output Current (continuous) 25A 40A

Input AC Current 4.5A @ 115V AC / 2.25A @ 230V AC 7.5A @ 115V AC / 3.75A @ 230V AC

Nominal Output Voltage 12V DC 12V DC

Output Connections 3 positive, 1 negative 3 positive, 1 negative

Universal AC Input Voltage 115–230V AC 115–230V AC

Input Frequency Range 50–60 Hz 50–60 Hz

Typical Float Voltage 13.5V DC 13.5V DC

Output Voltage Accuracy 0.05V DC 0.05V DC

Minimum Operating Temperature −20°C (−4°F) −20°C (−4°F)

Full Output Maximum Temperature 45°C (113°F) 45°C (113°F)

Minimum Storage Temperature −30°C (−22°F) −30°C (−22°F)

Maximum Storage Temperature 80°C (176°F) 80°C (176°F)

Warranty 5 Year 5 Year

Battery Types* Flooded, Gel, AGM, TPPL

(Thin Plate Pure Lead) Flooded, Gel, AGM, TPPL (Thin Plate Pure Lead)

Recommended for Battery Bank Sizes**

60Ah Minimum,

Example: 1 x Group 24

330Ah Maximum, Example: 3 x Group 31

60Ah Minimum, Example: 1 x Group 24

440Ah Maximum, Example: 4 x Group 31

Conductor Length in feet (meters) Charger Rating

25A 40A

6 ft (1.83 meters) 14 AWG (2.5mm²) 8 AWG (10mm²)

10 ft (3.05 meters) 12 AWG (4mm²) 8 AWG (10mm²)

15 ft (4.57 meters) 10 AWG (6mm²) 6 AWG (16mm²)

20 ft (6.09 meters) 8 AWG (10mm²) 6 AWG (16mm²)

25 ft (7.62 meters) 6 AWG (16mm²) 4 AWG (25mm²)

Recommended Battery Fuse

30A 60A

Region Line Neutral Ground (Earth)

North America Black White Green

Europe Brown Blue Green-Yellow

Australia/ New Zealand Brown or Red Blue or Black Green-Yellow

Table A: Minimum Recommended Wire Size*

Appropriate Fuses and Fuse Holders Charger Rating

Fuse Type Fuse Holder 25A 40A

MRBF Terminal Fuses 5191 Terminal Fuse Block 5175 (30A Fuse) 5178 (60A Fuse)

AMI®/MIDI® Fuses 7720 Safety Fuse Block 5250 (30A Fuse) 5253 (60A Fuse)

Table B: Recommended DC Circuit Protection

Table C: Typical AC Regional Wire Colors

Table D: AC Wire - Circuit Protection Selection Chart

7531 (25A) 7532 (40A)

Input Watts 450 750

120V AC Application 4.5A @ 100V AC 7.5A @ 100V AC

Minimum AC Wire Size 18 AWG (0.75mm²) 16 AWG (1.5mm²)

Circuit Breaker 10A 15A

230V AC Application* 2.25A @ 200V AC 3.75A @ 200V AC

Minimum Wire Size 18 AWG (0.75mm²) 18 AWG (0.75mm²)

Circuit Breaker 5A – 10A 5A – 10A

Typical of Europe

Type Absorb Volts Float Volts

FLA – Flooded Lead Acid 14.5V 13.5V

AGM – Absorbed Glass Mat 14.35V 13.3V

Gel – Gelled Electrolyte 14.1V 13.5V

TPPL – Thin Plate Pure Lead 14.7V

13.6V

User Adjustable 12.5V Default 12.5V Default

¹ Taken from Odyssey Tech Notes, Northstar operation Manual

Table E: Default Voltages by Battery Type

Batteries should match in chemistry, although many AGM’s and ﬂooded batteries are

compatible. Based on 25°C (77°F)

Based on 3% voltage drop. If fast charge recovery is important, use larger wire. Double the conductor

length entry to get a 1.5% drop, triple the conductor length to get a 1% voltage drop.

P12

7531 AND 7532 BATTERY CHARGERS

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

Product Dimensions

WARNING

For drip proof performance, and to meet ABYC requirements, the P12 Battery Charger must be mounted vertically as shown below.

Installation Clearances

P12

7531 AND 7532 BATTERY CHARGERS

Clearance for

#12, Ø1/4" M6

mounting hardware

7.80"

(198mm)

11.18"

(284mm)

7.40"

(188mm)

8.46"

(215mm)

4.30"

(109.1mm)

12.94"

(328.8mm)

14"-20

TOP

Recommended

side clearance

1.97

(50mm)

Recommended

overall envelope width

12.40

(315mm)

Recommended

clearance

for wire access

and inlet airﬂow.

3.94

(100.2mm)

Recommended

overall

envelope height

19.00

(480.6mm)

Recommended

top clearance

1.97

(50mm)

Recommended

clearance

for cooling fan exhaust.

do not block!

5.91

(150mm)

This

End

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

Included Components

Dielectric Grease

Mounting Screws

#12 x 1-1/4" sheet metal

screws (Use #3 Phillips

screwdriver)

Dielectric Grease

Used for Temperature Sensor and the

Optional Accessory P12 Remote Display Connections. View the

MSDS for the Dielectric Grease at bluesea.com/P12

Temperature Sensor

Flying lead, Battery Temp Sensor with

peel and stick adhesive

AC Strain Relief Insulating Cover Screws

M3 x 25mm pan-head machine screws (Use #1 Phillips screwdriver)

Recommended torque: 5–10 in-lb (0.6–1.1 Nm)

Pan-Head Machine Screws

M3.5 x 6mm

Recommended torque:

10–15 in-lb (1.0–1.8 Nm)

DC Strain Relief Clamp Screws

M3 x 25mm pan-head machine screws

Recommended torque:

5–10 in-lb (0.6–1.1 Nm)

DC Termination Nuts

1/4"-20 serrated ﬂange hex-nuts

(Use 10mm socket wrench with extension)

Recommended torque: 70–80 in-lb (8–9 Nm)

DC Safety Ground Nut

M6 hex-nut

P12

7531 AND 7532 BATTERY CHARGERS

ACR Screw

Terminal Connector

Battery Temperature

Sensor Screw

Terminal Connector

DC Termination Nut

1/4"-20 serrated ﬂange hex-nut

Accessory Pack Includes:

AC Strain Relief

and Insulating Cover

DC Strain

Relief Clamp

DC Strain Relief

Clamp Screw

M3 x 25mm pan-head

machine screw

P12 Battery Charger Hardware:

DC Safety Ground Nut

M6 hex-nut

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

Supplies Needed & Maintenance

1. AC Wire (see Table D page 5)

NOTE: Wire length must reach from the panel to the battery charger AC Connections with proper routing, support, drip loops, service loops, and termination.

NOTE: Yellow is preferred for negative however diagrams are drawn in black for visibility.

3. Fuse holders for connection to each battery. (see Table B page 5)

4. Fuses for fuse holders. (see Table B page 5)

5. Screwdrivers

• Flat blade screwdriver to release cover latch

• Phillips #2 – for AC termination and cover screws, and strain relief wire clamps

• Phillips #3 – for mounting screws

6. Socket wrench

• 7/16" socket with extension and ratchet handle or nut driver – for DC wire terminations

• 10mm socket – for DC safety ground termination

7. Ring terminals

• #6 (M3) ring or snap spade terminals sized for AC/Supply wire gauge (quantity 3)

• ¼" or M6 ring terminals sized for DC wire sizes (quantity 4)

8. Crimping tool or obtain wires that are pre-terminated

9. Appropriate heat shrink if pre-terminated wires were not acquired

2. DC Wire: Black or Yellow for negative and red for each positive. (see Table A page 5)

P12

7531 AND 7532 BATTERY CHARGERS

MAINTENANCE INSTRUCTIONS

Periodic Maintenance Items. All other servicing must be performed by qualiﬁed service personnel!

• Verify P12 Battery Charger screen shows no fault condition and indicates normal operation

• Check fuses or circuit breakers to verify like new condition. Conﬁrm no discoloration or corrosion exists and circuit breakers will manually

trip and reset.

• Check for proper ventilation and that no debris has collected on the fan shroud or items have been improperly stored around

the P12 Battery Charger.

• Check battery terminal connections (both at battery and at the P12 Battery Charger) for corrosion. Clean and reconnect immediately

upon signs of corrosion.

• Check batteries per manufacturer’s instructions and maintenance procedures.

• Check wire condition. Overheating due to excessively long or too small conductors will result in hardening of the insulation or burn

marks at connections. If any of these signs exist, immediately replace with proper sized conductors.

DC Output Fuse Replacement

• Replacement of DC output fuses.

a. CAUTION!! Before replacing output fuses disconnect all sources of AC and all DC batteries and loads from the charger.

If you are not comfortable working on electrical systems, do not proceed. Seek help from a qualiﬁed marine electrician.

b. Remove terminations cover from the charger.

c. The fuses are located on the lower right of the charger adjacent to the negative battery stud.

d. Carefully remove both fuses by pulling the fuse straight out from the socket.

e. Replacement fuses must be ATC

type fuses with ignition protected rating (use of non-ignition protected rated fuses will render the entire

charger non-ignition protected, and therefore unsafe for use in an environment that requires an ignition protected rating).

Proper fuses are as follows: Model 7531, two 20A ATC

Fuses, Model 7532, two 25A ATC

Fuses.

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

Installation & Operating Instructions

Installation Steps

1. Before beginning electrical installation, disconnect all positive and negative AC and DC power sources.

The P12 Battery Charger default startup mode is “User”. The battery charger will maintain a voltage but will not

charge batteries in this mode. After proper installation see page 11 to set up your battery type.

3. The yellow latches are locked/released by turning them ¼ turn with a ﬂat blade screwdriver.

2. To reduce the risk of electrical shock, mount the battery charger vertically, in a dry and well ventilated location.

For drip proof installation, mount the battery charger in a vertical orientation.

NOTE: The charger should be located near the batteries to minimize wire length and its associated voltage drop to maximize charging efﬁciency.

If the batteries are not close together, place the charger near the largest bank of batteries.

NOTE: DC wiring should safely reach each battery positive and the battery negative common bus bar. Fuses should be installed at the battery positive

connections to prevent battery power from feeding back into a fault in the wiring, or in the battery charger. See Table A and B on page 5 for recommended values.

5. Route DC wires from each charger output to battery fuse holder, see Wiring Connections Diagram page 10.

4. Then remove the AC and DC wire termination strain relief clamps by unfastening the screws.

AC Connections Strain Relief DC Connections Strain Relief

Best practices and ABYC standards recommend that every positive wire on the boat, outside the engine starting circuit, must have circuit protection.

Please reference ABYC E-11 electrical standard for the most up to date recommendations.

WARNING

Be sure the area around the charger and batteries is well ventilated while the batteries are being charged. This unit is must be located in a dry, well

ventilated area, free from unsecured hardware. Do not mount the unit directly above or below batteries to prevent corrosive electrolyte or gases from

damaging the unit.

EXTERNAL CONNECTIONS TO CHARGER SHALL COMPLY WITH THE UNITED STATES COAST GUARD ELECTRICAL

REGULATIONS ( 33CFR183 SUB PART I)

P12

7531 AND 7532 BATTERY CHARGERS

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

Main Negative BusBar

Line

Neutral

Ground

AC Connections

#6 (M3) Ring Terminals

DC Connections

1/4" (M6) Ring Terminals

Battery 1

Fuse Fuse Fuse

Temperature

Sense

Remote

Display

RJ45 Port

External

Shutdown

Start Isolation

ACR2

Engine Start

Switch ACR1

Engine Start

Switch ACR2

Start Isolation

ACR1

DC Safety Ground

Battery 2

Battery 3

Installation Instructions (continued)

NOTE: If you have a Blue Sea Systems ACR with Start Isolation it is possible to take advantage of the P12 Battery Charger’s ability to integrate with it. The

P12 is designed to charge three electrically independent batteries or battery banks. The P12 has the unique capability to individually move each battery out of

Absorption charging stage. This ensures batteries near their full charge do not continue to receive high constant voltages necessary in the Absorption stage. This is

optimal treatment for long battery life. Charge Coordination integrates with the Blue Sea Systems family of Automatic Charging Relays (ACRs) to force separation

of the battery banks while the P12 is operational, to allow batteries to individually exit the absorption stage. (see pages 22–23)

6. Route the AC wires from the charger to the AC panel and terminate wires at the charger.

7. Make the AC source connections to the appropriate panel circuit breaker and leave in the “off” position. (see Table D page 5).

The connection to the supply mains is to be in accordance with the national wiring.

NOTE: Connect AC wiring, but do not energize the circuit until AC insulating cover is installed, DC is connected, and DC fuses are installed.

Wiring Connections

1. Attach the battery charger remote connection to the back of the P12 Battery Charger Remote using dielectric grease. Connect to the Remote Display/Com

port of the charger.

2. Connect the Automatic Charging Relay(s) (ACR) wire to the ACR Connection port(s)

Optional Installations see pages 22–23

8. Recommended Connection: Attach the battery temperature sensor wire to the largest battery bank. If all battery banks are the same size attach to bank with the most loads.

Blue Sea Systems recommends using a high quality dielectric grease for remote control and temperature sensor connections.

a. Attach the sensor in the center of the long side of the battery.

b. If multiple batteries are in a battery bank attach sensor

in the center between multiple batteries.

c. When external circumstances could create a signiﬁcant

difference in temperature on one side of a battery versus

another, always attach temperature sensor on warmest side.

9. Install appropriate DC Fuses. (see Table B page 5)

10. Conﬁrm all connections are accurately installed per

Wiring Connections Diagram.

11. Secure AC and DC strain relief covers and fasten down.

12. Secure the termination cover over the connected wires

and latch the yellow tabs.

13. Restore AC power and turn on the AC supply circuit

breaker to the battery charger.

14. Perform the charger’s setup procedure as outlined in

Initial Charger Setup page 11.

P12

7531 AND 7532 BATTERY CHARGERS

NOTE: The external

shutdown input is a ¼"

male quick connect.

Applying a voltage

between +5 and +32

volts DC (referenced to

the battery negative)

will place the charger

into standby mode.

When the voltage is

removed, the charger

will resume charging.

If the installation does

not require use of this

terminal, it may be

left unconnected.

WARNING

If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

All-pole disconnection from the supply mains incorporated in the ﬁxed wiring shall be provided in accordance with AS/NZS 3000.

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

Initial Charger Setup

During Initial Charger Setup, or after resetting to factory defaults, the following screens require user input to provide

functional battery charging.

1. Using the left or right arrow button, scroll to the desired language.

Press the Select button.

2. Once the desired language is highlighted, press OK button.

Press the Cancel button to go back.

3. Using the left or right arrow button, scroll to the desired battery type.

Press the Select button.

4. Once the desired battery type is highlighted, press the OK button.

Press the Cancel button to go back.

Note: If User mode is selected batteries will not charge until Absorb and Float voltages are altered.

See page 12-13 for Advanced Charger Setup.

5. Press the Back button twice to go to the Charger Summary screen.

Note: If battery type is unknown, see the label on the battery or contact a qualiﬁed marine electrician.

CAUTION

Selecting a battery type different from the connected batteries could limit the life of the

batteries and damage them.

Your charger is now operational.

For advanced setup options and information on Absorb and Float voltage, as well as absorb timers,

See page 12.

P12

7531 AND 7532 BATTERY CHARGERS

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

Advanced Charger Setup

1. Press the Menu button.

2. Press the left

or right arrow buttons to scroll to the Fan Speed window

3. Press the Select button.

4. Press the up or down arrow buttons to select the desired speed.

a. High: The fan will spin up to its maximum speed. This is the recommended setting for optimal performance.

b. Low: The fan will spin up to a designated speed (below max). If there is a signiﬁcant load on the charger, it may limit its maximum output current in

order to maintain a safe internal temperature.

c. Off: Forces the Fan to stay off. If there is signiﬁcant load on the charger, it may limit its maximum output current to maintain a safe internal temperature.

6. Press the left

or right arrow buttons to scroll to the Max Output window.

7. Press the Select button.

8. Press the up or down arrow buttons to select the desired maximum output amperage. Low output may be selected to reduce load on the AC source.

AC current is approximately 15% of the DC current at 115V line voltage and 7% of the DC current at 230V line voltage.

9. Press the OK button once desired max amperage output is reached.

10. Press the left

or right arrow buttons to scroll to the Display window.

11. Press the Select button.

NOTE: The designated maximum amperage is the total available amperage to be supplied among all 3 outputs. Selecting an amperage less than the maximum

could result in under charging of batteries.

5. Press the OK button once desired speed is reached.

NOTE: Selecting High or Low will not necessarily turn the fan immediately on or increase the fan speed. In either of these settings the charger will only alter the fan

speed if the internal temperature rises enough to warrant fan circulation. The fan Low setting is for quiet mode.

12. Press the up or down arrow buttons to scroll to the desired display setting.

13. Press the Select button on the desired display setting to enable editing that setting.

a. Once selected, the amount of contrast and backlight can be adjusted using the left and right arrow buttons.

b. Press the OK button to enable desired setting.

14. Scroll to Backlight Timer and press the Select button.

a. Using the left and right arrow buttons you may adjust the length of seconds the backlight will remain on.

b. The backlight timer can be adjusted between 5 and 59 seconds. It may also be set permanently on or permanently off.

15. Press the OK button once desired backlight setting is reached.

16. Scroll to Language and press the Select button to adjust the display language.

17. Using the left or right arrow buttons scroll to the desired language.

18. Press the OK button.

Complete this setup to change language, limit fan noise, adjust backlight display and limit AC current draw.

P12

7531 AND 7532 BATTERY CHARGERS

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

2. Press the left or right arrow buttons to scroll to the Fan Speed window

3. Press the Select button.

4. Press the up or down arrow buttons to select the desired speed.

a. High: The fan will spin up to its maximum speed. This is the recommended setting for optimal performance.

b. Low: The fan will spin up to a designated speed (below max). If there is a signiﬁcant load on the charger, it may limit its maximum output current in

order to maintain a safe internal temperature.

c. Off: Forces the Fan to stay off. If there is signiﬁcant load on the charger, it may limit its maximum output current to maintain a safe internal temperature.

6. Press the left or right arrow buttons to scroll to the Max Output window.

7. Press the Select button.

8. Press the up or down arrow buttons to select the desired maximum output amperage. Low output may be selected to reduce load on the AC source.

AC current is approximately 15% of the DC current at 115V line voltage and 7% of the DC current at 230V line voltage.

19. Once desired display settings are enabled press Back.

20. Press the left or right arrow button to scroll to the Battery window.

21. Press the Select button.

Advanced Charger Setup (continued)

26. Press the Back button twice to return to the Charger Summary screen.

27. Your P12 Battery Charger is now setup and fully operational.

22. While the cursor blinks on battery type press the Select button.

23. Use the left

or right arrow buttons to scroll to desired battery type.

24. Press the OK button.

25. For optimal charging it is recommended to set absorption timers and End Absorb Amps. If Amp Hour Capacity is known, continue to page 14 for more information.

CAUTION

Selecting a battery type different from the connected batteries could limit the life of the batteries and damage them.

NOTE: To adjust Absorb and Float voltage, “User” must be the selected battery type. The default Absorb voltages for each battery type can be seen in Table E above.

Warning: Incorrect Absorb and Float voltages could reduce the life of your batteries. Contact your battery manufacturer for recommended Absorb and Float voltages.

To reset the P12 Battery Charger to factory defaults, press and hold the two right buttons for ten seconds.

Press the OK button for ﬁve seconds to proceed with resetting to factory defaults or press the Cancel button to return to the previous screen.

Note: Resetting the P12 Battery Charger to factory defaults will erase previously saved data and settings.

Reset to Manufacturer Defaults

Type Absorb Volts Float Volts

FLA – Flooded Lead Acid 14.5V 13.5V

AGM – Absorbed Glass Mat 14.35V 13.3V

Gel – Gelled Electrolyte 14.1V 13.5V

TPPL – Thin Plate Pure Lead 14.7V

13.6V

User Adjustable 12.5V Default 12.5V Default

¹ Taken from Odyssey Tech Notes, Northstar operation Manual

Table E: Default Voltages by Battery Type

Batteries should match in chemistry, although many AGM’s and ﬂooded batteries are

compatible. Based on 25°C (77°F)

P12

7531 AND 7532 BATTERY CHARGERS

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

Absorption Parameters and Timers

CAUTION

The default Absorption Timer values are set to satisfy a majority of the battery conﬁgurations that exist. Unwarranted changes to Absorption timers could

result in damage to the batteries and reduced battery life. To optimize Absorption Timer based on speciﬁc conﬁgurations, please contact your

battery manufacturer for setting guidelines for your speciﬁc battery.

The Absorption stage is the charging stage in which a battery “ﬁlls” to max capacity. Absorption timers help deﬁne the amount of time a battery bank will

remain in the Absorption stage. Having a correct Absorption time is vital for optimum charging of a battery bank. Under Absorption can lead to a battery

being consistently under-charged causing sulfate buildup. Over Absorption can dry out the electrolytes in a battery. Both of these conditions can lead to

reduced battery life.

There are three user selectable parameters that help deﬁne when a connected battery bank will be moved from Absorption to either Pre-Float, or Float.

Minimum Absorption Time: 1 hour default

The minimum amount of time a battery bank will be in Absorption. The battery charger will not move a battery from Absorb to Float unless the Minimum Absorption Time is met.

Maximum Absorption Time: 4 hour default

The maximum amount of time a battery bank can remain in Absorption. While still maintaining its Absorption voltage, if a battery has been in Absorption for the maximum

designated time it will move into Float even if End Absorb Amps is elevated. This is commonly caused when active loads are present.

Recommended End Absorption Amps

End Absorb Amps will vary based on your speciﬁc system. To set the correct End Absorb Amps it is recommended

that you monitor the amperage entering your battery banks near the end of the absorption cycle. Constant loads

will affect this number, and should be incorporated into End Absorb Amps if present. However, in a typical system

(without constant loads) it is recommended that the End Absorb Amps be 1% of your battery banks amp-hour

capacity (see Table F).

End Absorption Amps

The maximum amount of current that a battery bank can receive while in Absorption and still change to Float. If a

load is active and drawing more than the designated End Absorption Amps, the battery bank will not leave Absorption

until the maximum Absorption time is met. For a battery bank to move from Absorption to Float before the maximum

Absorption time is met, the minimum Absorption time must be met, and the amperage output must be less than or

equal to the designated End Absorb Amps.

Flooded AGM Gel TPPL

Group

Size

1% End

Amps

1% End

Amps

1% End

Amps

1% End

Amps

24 75 0.8 79 0.8 73 0.7 76 0.8

27 90 0.9 92 0.9 86 0.9 91 0.9

31 105 1.1 105 1.1 97 1.0 102 1.0

4D 150 1.5 198 2.0 183 1.8 185 1.9

8D 200 2.0 245 2.5 225 2.3 228 2.3

Recommended Absorption Time

Minimum and Maximum Absorb Times can vary from installation to installation. It is recommended that Minimum and Maximum Absorption Times be based on the time it takes

a battery bank to reach End Absorb Amps. Read and understand the End Absorb Amps section above and set according to your system. After an accurate End Absorb Amperage

is set, monitor the minimum and maximum time it takes for each battery bank to reach their End Absorb Amps. The Minimum Absorb Time should be based on the minimum time

it takes a particular battery bank to reach End Absorb Amps. The Maximum Absorb Time should be an hour more than it takes a deeply discharged battery bank to reach End

Absorb Amps. It is recommended to monitor charging while the battery banks are in different states of discharge to get the most accurate Minimum and Maximum Absorb Times.

Table F: Approximate End Absorb Amps

(1% of Ah Capacity)

Blue Sea Systems’ P12 Battery Chargers are designed and

tested to comply with California Energy Commission (CEC)

efﬁciency requirements and ship with these settings by default.

To disable this factory setting, select Charger Setup Menu,

select Battery and then press the down arrow and select

Set Absorb Timers. Then press the down arrow four times

to view General Charger Settings screen. Press Select and use

the left or right arrow buttons to toggle between ON

and OFF.

Complies with California Energy Commission (CEC)

efﬁciency requirements

Does not comply with California Energy Commission (CEC)

efﬁciency requirements

Energy Save Feature Control

P12

7531 AND 7532 BATTERY CHARGERS

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

Table F: Approximate End Absorb Amps

(1% of Ah Capacity)

Minimum Charge Temperature: The default is 0ºC

The lowest temperature of the sensor in which the charger will continue charging. If the temperature sensor measures below the minimum charge temperature, the charger will

enter standby mode, and cease to charge.

WARNING

Altering the default temperature parameters could cause serious property or personal damage. Contact your battery manufacturer to clarify the correct

temperature parameters for your speciﬁc batteries.

NOTE: Temperature parameters refer to the temperature measured at the temperature sensor, not the temperature of the charger. In this manual all temperatures

will be referenced in degrees in Celsius (°C). The user selectable range for battery temperature parameters is -20°C to 60°C. Ensure proper placement of battery

temperature sensor by referencing Step 8 on page 10

Maximum Charge Temperature: The default is 49ºC

The highest temperature of the sensor in which the charger will continue charging. If the temperature sensor measures above the maximum charge temperature, the charger will

enter standby mode, and cease to charge.

Battery Temperature Compensation (Tempco)

Battery temperature compensation is output voltage regulation based on battery temperature variances. Since batteries can see extreme temperature differences it is important

to regulate output voltage with temperature. A battery in a freezing environment should not be charged the same as a battery in a hot environment. The P12 Battery Charger

is set at a baseline of 25°C. Every degree variance from this baseline will result in a voltage variance on all outputs. For every degree above 25°C the charger will reduce all

output voltages by the value deﬁned in Battery Tempco. For every degree below 25°C the charger will increase all output voltages by the value deﬁned in Battery Tempco. For

example, with the default Battery Tempco set to -30mv/°C if the temperature sensor reads 26°C, then all output voltages will be reduced by .03V (30mv). If given the same

Battery Tempco and the temperature sensor reads 24°C, then all output voltages will be increased by .03V (30mv).

CAUTION

Charging batteries below 0°C can be potentially dangerous. Internal battery liquid can freeze and charging a frozen battery could cause serious property or

personal damage. Contact your battery manufacturer for minimum safe charging temperature for your batteries before altering.

CAUTION

Charging batteries above 49°C can be potentially dangerous. Contact your battery manufacturer for the maximum safe charging temperature for your

batteries before altering.

CAUTION

Altering the battery temperature compensation value incorrectly can cause adverse effects on

your battery, by potentially reducing its life. Contact your battery manufacturer to ﬁnd out the

speciﬁc temperature compensation parameters for your batteries.

Absorption Timer Counter

The P12 battery charger uses a counter to determine the amount of time a battery bank should remain in Absorb relative to the Maximum Absorb Time. The Absorb timers counter

can be seen in the System Status Screen and also referenced on page 19.

Absorption Parameters and Timers (continued)

Temperature Parameters

Available Timer Modes

When in Float or Standby, the timer will pause.

When in Pre-Float mode the timer for that channel will pause.

When in Bulk mode the remaining time will increase.

When in Absorption mode, the remaining time will decrease.

Once a battery bank’s Absorb timer is reduced to zero, then its output will be changed to Pre-Float. There are

other factors in a battery bank leaving the Absorption stage prior to the Absorb timer running out. Once all battery

banks leave Absorption, all outputs will enter the Float stage, or Rest stage if in Energy Save mode.

P12

7531 AND 7532 BATTERY CHARGERS

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

6. Press “I Accept” to continue.

7. Using the battery manufacturer’s parameters, input the correct equalization voltage, amperage, and time on the battery bank you would like to equalize.

You may only equalize one battery bank at a time.

Equalization

Deﬁnition of Equalization

Equalization is an increased voltage overcharge performed only on ﬂooded lead acid batteries. Once a battery is fully charged equalization increases the voltage and forces

additional charge into the battery to combat negative chemical side effects that can occur in ﬂooded batteries. It is done to compensate for stratiﬁcation, a

condition where the acid concentration is uneven throughout the battery, and typically higher at the bottom. It is also done to remove sulfate crystals that build up

on the lead plates in ﬂooded batteries.

Prior to Equalization

Contact the manufacturer of your ﬂooded lead acid batteries to conﬁrm the parameters of equalizing your speciﬁc batteries. Every battery manufacturer deﬁnes different

equalization parameters which are important to understand prior to equalization. All batteries must be fully charged and not under load from any device. The P12 Battery

Charger will not allow equalization to occur if batteries are discharged or powering any device.

Equalization Process

1. Conﬁrm batteries are fully charged by verifying the charger is in Float mode with no active loads.

2. Turn off or disconnect all DC devices that are connected to the batteries. Disconnect the battery banks not being Equalized by removing the fuses at

the battery connection.

NOTE: Equalization parameters vary based on battery size. Conﬁrm parameters for every battery connected to the charger before continuing.

WARNING

Equalization is a user selectable and potentially dangerous charging stage that should not be performed without sufﬁcient knowledge. Personal or property

damage may occur if equalization is performed incorrectly. It is highly recommended that you seek professional guidance before performing equalization.

Equalization causes off gassing of harmful chemicals inside of the battery. Only perform equalization while the batteries are in a well-ventilated area away

from persons and animals.

CAUTION

Equalization may only be performed on ﬂooded (wet) lead acid batteries. Serious personal or property damage may occur if equalization is

performed on any battery type other than ﬂooded lead acid batteries.

NOTE: Equalization will only occur if the battery type is set to “Flooded Lead Acid” (FLA) or “User”. Do not proceed if you are using any other battery type.

See bluesea.com/P12 for details.

4. From any screen simultaneously press and hold the left and right most buttons for 5 seconds.

5. Read and understand the caution screen before proceeding.

3. Conﬁrm use of ﬂooded lead acid batteries.

NOTE: Equalization will not occur if steps 1 and 2 are not met.

P12

7531 AND 7532 BATTERY CHARGERS

Speciﬁcations are subject to change. See bluesea.com/P12 for current information.

8. To change battery, use the up down arrow buttons to scroll the cursor to the Bat1 window.

9. Press the Select button.

10. Using the left and right arrow buttons, scroll between the three different battery banks connected to the charger.

11. Conﬁrm Equalization parameters for the battery you wish to equalize.

12. Using the up down arrow buttons, scroll the cursor to the StartEQ window.

13. Press the Select button.

14. The charger will now begin to equalize and will display.

15. Monitor batteries and battery temperature throughout the Equalization process.

16. You may pause Equalization at any time by pressing the pause button.

17. If at any point during Equalization a DC load is applied to the battery being equalized, Equalization will stop.

18. You may stop Equalization at any time by pressing the stop

button.

Equalization (continued)

NOTE: If you receive the below warning screen conﬁrm batteries are fully charged and all DC loads connected to the batteries are turned off. Once complete proceed

back to step 1 of the Equalization process.

NOTE: Pressing stop will return you to the Charger Summary screen.

19. Once the max Equalization voltage is reached the battery bank will begin to equalize for the designated Equalization time.

20. After the designated Equalization time is met Equalization will stop and the charger will return to the Charger Summary Screen.

P12

7531 AND 7532 BATTERY CHARGERS