KitchenAid KBLC36FTS - 36" Bottom-Freezer Refrigerator Guide d'installation

BOTTOM-MOUNT

BUILT-IN REFRIGERATOR

Installation Guide

IMPORTANT: READ AND

SAVE

THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.

REFRIGERADOR EMPOTRADO CON

CONGELADOR EN LA PARTE INFERIOR

Guía de instalación

IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. LA INSTALACIÓN REQUIERE DE 2 O MÁS PERSONAS.

RÉFRIGÉRATEUR ENCASTRÉ AVEC

CONGÉLATEUR EN DESSOUS

Guide d’installation

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. L’INSTALLATION NÉCESSITE L’INTERVENTION DE 2 PERSONNES OU PLUS.

Table of Contents/Índice/Table des matières ..................................................................2

W10379132A

2

TABLE OF CONTENTS

REFRIGERATOR SAFETY...........................................................................3

MODELS....................................................................................................... 4

INSTALLATION REQUIREMENTS ............................................................. 5

Tools and Parts......................................................................................... 5

Location Requirements............................................................................. 5

Electrical Requirements............................................................................ 6

Water Supply Requirements..................................................................... 7

Tipping Radius..........................................................................................7

Product Dimensions .................................................................................8

Door Swing Dimensions ........................................................................... 9

Overlay Series Door Panel and Cabinetry Clearance

(36" [91.4 cm] Models)............................................................................10

Overlay Series Door Panel & Cabinetry Clearance

(42" [106.7 cm] Models)..........................................................................12

Overlay Series Custom Panels ...............................................................14

Custom Overlay Panel Dimensions........................................................14

Classic, Architect

®

, and Overlay Series Factory Panels and Kits

(36" [91.4 cm] Models)............................................................................16

Classic Series Custom Panels (36" [91.4 cm] Models).......................... 16

Classic and Architect

®

Series Custom Side Panels ............................... 17

Overlay Series Custom Side Panels....................................................... 18

INSTALLATION INSTRUCTIONS ............................................................. 20

Unpack the Refrigerator ......................................................................... 20

Reduce Tipping Radius .......................................................................... 20

Move the Refrigerator into House .......................................................... 20

Install Anti-Tip Boards ............................................................................ 21

Connect the Water Supply ..................................................................... 21

Plug in Refrigerator................................................................................. 23

Move Refrigerator to Final Location....................................................... 23

Level and Align Refrigerator ................................................................... 23

Install Overlay and Classic Series Custom Panels ................................ 24

Adjust Door(s) ......................................................................................... 25

Install Side Panel .................................................................................... 27

Install Base Grille .................................................................................... 28

Complete Installation.............................................................................. 28

ÍNDICE

SEGURIDAD DEL REFRIGERADOR........................................................29

MODELOS..................................................................................................30

REQUISITOS DE INSTALACIÓN ..............................................................31

Piezas y herramientas.............................................................................31

Requisitos de ubicación .........................................................................31

Requisitos eléctricos...............................................................................32

Requisitos del suministro de agua .........................................................33

Arco de vuelco........................................................................................33

Medidas del producto.............................................................................34

Medidas de oscilación de la puerta........................................................35

Espacio para el panel de la puerta de la serie Overlay y

para los gabinetes (modelos de 36" [91,4 cm])......................................36

Espacio para el panel de la puerta de la serie Overlay y

para los gabinetes (modelos de 42" [106,7 cm])....................................38

Paneles a la medida de la Serie Overlay ................................................40

Dimensiones del panel recubierto a la medida ......................................40

Paneles y juegos de fábrica para las Series

Classic, Architect

®

y Overlay (modelos de 36" [91,4 cm])...................... 42

Paneles a la medida para la Serie Classic

(modelos de 36" [91,4 cm])..................................................................... 42

Paneles laterales a la medida para las Series Classic y Architect

®

....... 43

Paneles laterales a la medida para la Serie Overlay .............................. 44

INSTRUCCIONES DE INSTALACIÓN...................................................... 46

Desempaque el refrigerador................................................................... 46

Cómo reducir el arco de vuelco ............................................................. 46

Cómo hacer entrar el refrigerador en la casa ........................................ 46

Cómo instalar los tableros antivuelco .................................................... 47

Conexión del suministro de agua........................................................... 47

Cómo enchufar el refrigerador ............................................................... 49

Cómo mover el refrigerador a su ubicación final................................... 49

Nivelación y alineamiento del refrigerador............................................. 49

Cómo instalar los paneles a la medida para

las Series Overlay y Classic.................................................................... 50

Cómo ajustar la(s) puerta(s).................................................................... 52

Cómo instalar el panel lateral ................................................................. 53

Cómo instalar la rejilla de la base........................................................... 54

Cómo terminar la instalación.................................................................. 54

TABLE DES MATIÈRES

SÉCURITÉ DU RÉFRIGÉRATEUR ...........................................................55

MODÈLES ..................................................................................................56

EXIGENCES D’INSTALLATION................................................................57

Outillage et pièces ..................................................................................57

Exigences d’emplacement .....................................................................57

Spécifications électriques ......................................................................58

Spécifications de l’alimentation en eau..................................................59

Rayon de basculement...........................................................................59

Dimensions du produit............................................................................60

Dimensions pour le pivotement des portes ...........................................61

Série Overlay - Panneau de porte et placard –

dimensions et espace libre (modèles de 36" [91,4 cm]) ........................62

Série Overlay - Panneau de porte et placard –

dimensions et espace libre (modèles de 42" [106,7 cm]) ......................64

Panneaux personnalisés de la série Overlay..........................................66

Panneaux personnalisés - Dimensions .................................................. 66

Ensembles de panneaux d'origine de la série

Classic, Architect

®

et Overlay (modèles de 36" [91,4 cm]).....................68

Panneaux personnalisés de la série Classic

(modèles de 36" [91.4 cm]).................................................................... 68

Panneaux latéraux personnalisés des séries Classic et Architect

®

....... 69

Panneaux latéraux personnalisés de la série Overlay............................ 70

INSTRUCTIONS D’INSTALLATION ......................................................... 72

Déballage du réfrigérateur...................................................................... 72

Réduction du rayon de basculement ..................................................... 72

Faire entrer le réfrigérateur dans le domicile.......................................... 72

Installation de planches antibasculement.............................................. 73

Raccordement à l'alimentation en eau................................................... 73

Brancher le réfrigérateur......................................................................... 75

Déplacement du réfrigérateur à l'emplacement final............................. 75

Réglage de l'aplomb et alignement du réfrigérateur.............................. 75

Installation des panneaux personnalisés des

séries Overlay et Classic ........................................................................ 76

Ajustement de la (des) porte(s)............................................................... 78

Installation du panneau latéral................................................................ 79

Installation de la grille de la base ........................................................... 80

Achever l’installation............................................................................... 80

3

REFRIGERATOR SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

4

MODELS

Architect

®

Series (36" [91.4 cm] Models)

Features wraparound styling that complements the contoured

door handles. This series provides a warm commercial-looking

built-in refrigerator.

KBRC36FTS KBLC36FTS

Classic Series (36" [91.4 cm] Models)

Features traditional style trim, factory-installed, to provide a

“framed” look. This series requires the installation of custom panels

that are not included.

KBRS36FTB KBRS36FTX KBLS36FTB

KBLS36FTX

Overlay Series (36" [91.4 cm] Models)

Features factory-installed, overlay style trim, to provide a

“frameless” look. This series requires the installation of custom

panels, handles, and standoffs.

KBRO36FTX KBLO36FTX

Architect

®

Series (42" [106.7 cm] Models)

Features wraparound styling that complements the contoured door

handles. This series provides a warm commercial-looking built-in

refrigerator.

KBFC42FTS

5

INSTALLATION

REQUIREMENTS

Tools and Parts

IMPORTANT:

■ Installer: Leave Installation Instructions with the homeowner.

■ Homeowner: Keep Installation Instructions for future

reference. Save these Installation Instructions for the local

electrical inspector’s use.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

PARTS NEEDED:

■ Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)

■ One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)

■ Order factory panels, make custom panels or consult a

qualified cabinetmaker or carpenter to make the panels.

Classic Series: Order factory panels, make custom panels, or

consult a qualified cabinetmaker or carpenter to make the

panels. See “Installation Requirements” for more information.

Overlay Series: Make custom panels, or consult a qualified

cabinetmaker or carpenter to make the panels. See

“Installation Requirements” for more information.

Architect

®

Series is shipped complete.

■ If you are connecting the water line directly to copper tubing

and not to a shutoff valve, you need a ferrule, a union, and a

¹⁄₄" compression fitting.

Location Requirements

The refrigerator can be recessed in an opening between cabinets

or installed at the end of a cabinet run using a side panel to

enclose the refrigerator.

IMPORTANT:

■ Observe all governing codes and ordinances.

■ It is recommended that you do not install the refrigerator near

an oven, radiator, or other heat source.

■ Do not install in a location where the temperature will fall

below 55°F (13°C).

■ Floor must support the refrigerator weight, more than 600 lbs

(272 kg), door panels and contents of the refrigerator.

■ Ceiling height must allow for side tipping radius. See “Tipping

Radius.”

■ Location should permit door to open fully. See “Door Swing

Dimensions.”

■ Location must permit top grille removal. See “Opening

Dimensions.”

Opening Dimensions

■ To avoid tipping during use, the solid soffit must be within 1"

(2.5 cm) maximum above the refrigerator. If the solid soffit is

higher than 1" (2.5 cm) or one is not available, then the

refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to the

rear wall studs 80" to 90" (203 to 229 cm) above the floor. See

“Install Anti-Tip Boards” for more information.

Overlay Series (42" [106.7 cm] Models)

Features factory-installed, overlay style trim, to provide a

“frameless” look. This series requires the installation of custom

panels, handles, and standoffs.

KBFO42FTX

■ Cordless drill ■ Tor x

®†

T15 and T27 screwdrivers

■ Drill bits ■ ¹¹⁄₃₂" Nut driver

■ Two adjustable

wrenches

■ ³⁄₈", ¹⁄₄", and ¹⁄₂" Open-end

wrenches

■ Phillips screwdriver ■ ⁵⁄₃₂" Hex key

■ Small level ■ ¹⁄₄" and ⁵⁄₁₆" Socket drivers

■ Appliance dolly ■ Tape measure

■ Utility knife

†®TORX is a registered trademark of Saturn Fasteners, Inc.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

6

NOTE: A clearance of ¹⁄₂" (1.3 cm) must be maintained in front

of the refrigerator’s side trim in order for the top grille to be

removed.

■ A grounded 3 prong electrical outlet should be placed within

4" (10.2 cm) of the right side cabinets or end panel. See

“Electrical Requirements” for additional information.

■ The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible

area. If the water shutoff valve is not in the cabinets, the

plumbing for the water line can come through the floor or the

back wall. See “Water Supply Requirements” for more specific

information.

NOTE: Flooring under refrigerator must be at same level as the

room.

Electrical Requirements

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz., AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault

Circuit Interrupter) protected outlet, nuisance tripping of the

power supply may occur, resulting in loss of cooling. Food quality

and flavor may be affected. If nuisance tripping has occurred, and

if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, remove the top grille and turn the master

power switch to OFF or disconnect power at the circuit breaker

box.

When you are finished, turn ON the master power switch or

reconnect power at the circuit breaker box. Then reset the control

to the desired setting.

Model Width A (as shown above) Dimension B

(as shown above)

36

42

35¹⁄₂" (90.2 cm)

41¹⁄₂" (105.4 cm)

4" (10.2 cm)

10" (25.4 cm)

¹⁄₂"

(1.3 cm)

80" - 90"

(203-229 cm)

6"

(15.2 cm)

83¹⁄₂" (212.1 cm) min.

84

³⁄₄" (215 cm) max.

to bottom of solid soffit

24"

(60.96 cm) min.

1"

(2.54 cm)

77"

(196 cm)

6"

(15.2 cm)

6"

(15.2 cm)

A

Width

(see chart following)

B

Dimension

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

7

Water Supply Requirements

■ All installations must meet local plumbing code requirements.

■ The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible

area. The right-hand side is recommended. The access hole

through the cabinet must be within ¹⁄₂" (12.7 mm) of the rear

wall.

NOTE: If the water shutoff valve is in the back wall behind the

refrigerator, it must be at an angle so that the tube is not

kinked when the refrigerator is pushed into its final location.

■ If the water shutoff valve is not in the cabinets, the plumbing

for the water line can come through the floor. A ¹⁄₂" (12.7 mm)

hole for plumbing should be drilled at least 6" (15.2 cm) from

the right or left hand side cabinet or panel. On the floor, the

hole should be no more than 1" (2.54 cm) away from the back

wall. See “Connect the Water Supply.”

■ If additional tubing is needed, use copper tubing and check

for leaks. Install the copper tubing only in areas where the

household temperatures will remain above freezing.

■ Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve

which reduces water flow and clogs more easily.

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi

(207 and 827 kPa) is required to operate the water dispenser and

ice maker. If you have questions about your water pressure, call a

licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi

(207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

■ If your refrigerator has a water filter cartridge, it may further

reduce the water pressure when used in conjunction with a

reverse osmosis system. Remove the water filter cartridge.

If you have questions about your water pressure, call a licensed,

qualified plumber.

Tipping Radius

Be sure there is adequate ceiling height to stand the refrigerator

upright when it is moved into place.

■ The dolly wheel height must be added to the tipping radius

when a dolly is used.

■ If needed, the tipping radius can be reduced. See “Reduce

Tipping Radius.”

Side Tipping Radius (36" [91.4 cm] Models)

Side Tipping Radius (42" [106.7 cm] Models)

24"

(60.96 cm) min.

1"

(2.54 cm)

6"

(15.2 cm)

6"

(15.2 cm)

6"

(15.2 cm)

A. Tip this side only.

90¹⁄₂"

(229.9 cm)

A

93"

(236.2 cm)

A

8

Product Dimensions

Side View

■ The depth from the front of the top grille to the back of the

refrigerator cabinet is 25³⁄₈" (64.5 cm).

■ The power cord is 84" (213 cm) long.

■ The water line attached to the back of the refrigerator is 5 ft

(1.5 m) long. Height dimensions are shown with leveling legs

extended ¹⁄₈" (3 mm) below the rollers.

*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.

Top View

36" (91.4 cm) Models

42" (106.7 cm) Models

Front View

■ Width dimensions were measured from trim edge to trim

edge.

■ Height dimensions are shown with leveling legs extended ¹⁄₈"

(3 mm) below the rollers.

36" (91.4 cm) Models

*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.

A

23¹⁄₂"

(59.7 cm)

84" (213.4 cm)

Power Cord

*83³⁄₈"

(211.8 cm)

*3

¹⁄₂" (8.9 cm)

25³⁄₈"

(64.5 cm)

35¹⁄₄"

(89.5 cm)

25³⁄₈"

(64.5 cm)

41

¹⁄₄"

(105 cm)

36¹⁄₄" (92 cm)

*83³⁄₈"

(211.8 cm)

9

42" (106.7 cm) Models

*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.

Door Swing Dimensions

The location must permit the door to open to a minimum of 90°.

Allow 4¹⁄₂" (11.4 cm) minimum space between the side of the

refrigerator and a corner wall.

NOTE: More clearance may be required if you are using overlay

panels or custom handles.

To adjust the door swing, see “Adjust Door Swing.”

36" (91.4 cm) Models

42" (106.7 cm) Models

42¹⁄₄" (107.3 cm)

*83³⁄₈"

(211.8 cm)

110˚

90˚

23"

(58 cm)

max.

51"

(130 cm)

59"

(150 cm)

130˚

110˚

90˚

130˚

110˚

90˚

13

¹⁄₂"

(34.3 cm)

max.

40⁷⁄₁₆"

(102.7 cm)

44¹⁄₄"

(112.3 cm)

130˚

10

Overlay Series Door Panel and Cabinetry Clearance (36" [91.4 cm] Models)

The custom door panels and adjacent cabinetry must be designed so that there is sufficient clearance for the doors to swing open. If

the refrigerator is to be installed close to the wall, see “Door Swing 90°” on next page.

When the doors are closed the refrigerator will extend beyond the face of the adjacent cabinetry to some degree.

NOTE: For Overlay Series models, rout the

hinge side of the custom door panels to a

radius that is equal to at least half the

thickness of the panel if a 130˚ door swing is

desired. See “Adjust Doors.”

Spacer Panel

1

/4" (6.35 mm)

3

/4" (1.9 cm)

1" (2.5 cm)

1

/2" (1.3 cm)

1"

1

/4"

1

/2"

1"

(2.5 cm)

1

(3.2 cm)

1

/4"

1

(3.8 cm)

1

/2"

1

/2"

Refrigerator

Side Trim

Door

Hinge

Backer Panel

Overlay Panel

Door Swing 110˚

Actual Size

Refrigerator to

Cabinetry Clearance

(2.5 cm)

(3.2 cm)

(3.8 cm)

(1.3 cm)

NOTE: Allow ¹⁄₂"

(1.3 cm) clearance

between overlay

panel and cabinetry.

Cabinetry

3

/4"

(1.9 cm)

11

Allow a minimum of 4¹⁄₂" (11.4 cm) of space between the side of the refrigerator and a corner wall. More clearance may be needed if

thicker custom panels or custom handles are used. Do not overlook baseboards.

1

/4" (6.35 mm)

3

/4" (1.9 cm)

1" (2.5 cm)

1

/2" (1.3 cm)

3

/4"

1"

1

/4"

1

/2"

1

/2"

Refrigerator

Side Trim

Door

Backer Panel

Overlay Panel

Hinge

Door Swing 90˚

Actual Size

Refrigerator to

Cabinetry Clearance

(1.9 cm)

(2.5 cm)

(3.8 cm)

(1.3 cm)

(3.2 cm)

Spacer Panel

Cabinetry

1

/2"

3

/4"

1"

(1.3 cm)

(1.9 cm)

(2.5 cm)

90˚ Door

Stop Position

12

Overlay Series Door Panel and Cabinetry Clearance (42" [106.7 cm] Models)

The custom door panels and adjacent cabinetry must be designed so that there is sufficient clearance for the doors to swing open. If

the refrigerator is to be installed close to the wall, see “Door Swing 90°” on next page.

When the doors are closed the refrigerator will extend beyond the face of the adjacent cabinetry to some degree.

NOTE: For Overlay Series models, rout the

hinge side of the custom door panels to a

radius that is equal to at least half the

thickness of the panel if a 130˚ door swing is

desired. See “Adjust Doors.”

Spacer Panel

1

/4" (6.35 mm)

3

/4" (1.9 cm)

1" (2.5 cm)

1

/2" (1.3 cm)

1"

1

/4"

1

/2"

1"

(2.5 cm)

1

(3.2 cm)

1

/4"

1

(3.8 cm)

1

/2"

1

/2"

Refrigerator

Side Trim

Door

Hinge

Backer Panel

Overlay Panel

Door Swing 110˚

Actual Size

Refrigerator to

Cabinetry Clearance

(2.5 cm)

(3.2 cm)

(3.8 cm)

(1.3 cm)

NOTE: Allow ¹⁄₂"

(1.3 cm) clearance

between overlay

panel and cabinetry.

Cabinetry

3

/4"

(1.9 cm)

13

Allow a minimum of 4¹⁄₂" (11.4 cm) of space between the side of the refrigerator and a corner wall. More clearance may be needed if

thicker custom panels or custom handles are used. Do not overlook baseboards.

1

/4" (6.35 mm)

3

/4" (1.9 cm)

1" (2.5 cm)

1

/2" (1.3 cm)

3

/4"

1"

1

/4"

1

/2"

1

/2"

Refrigerator

Side Trim

Door

Backer Panel

Overlay Panel

Hinge

Door Swing 90˚

Actual Size

Refrigerator to

Cabinetry Clearance

(1.9 cm)

(2.5 cm)

(3.8 cm)

(1.3 cm)

(3.2 cm)

Spacer Panel

Cabinetry

1

/2"

3

/4"

1"

(1.3 cm)

(1.9 cm)

(2.5 cm)

90˚ Door

Stop Position

14

Overlay Series Custom Panels

Custom overlay panels allow you to blend the exterior of your

refrigerator into the overall kitchen décor and to use custom

handles for additional design flexibility.

The custom panels must have backer panels attached in order to

mount them to the refrigerator. It is most common to work with

three panels, as shown in the following graphic: a decorative

overlay panel, a ¹/₈" (3.18 mm) spacer panel or spacer strips and a

¹/₄" (6.35 mm) backer panel.

In some cases, your cabinet manufacturer may choose to work

with one panel routed for the different dimensions. Follow these

panel dimension and placement instructions to be sure that the

custom overlay panels will fit properly.

IMPORTANT:

■ For 36" (91.4 cm) models, the refrigerator door overlay panel

cannot exceed 50 lbs (23 kg) and the freezer drawer overlay

panel cannot exceed 20 lbs (9.1 kg).

■ For 42" (106.7 cm) models, the refrigerator door overlay panel

cannot exceed 30 lbs (13.5 kg) and the freezer drawer overlay

panel cannot exceed 25 lbs (11.4 kg).

■ The weight of the top grille overlay panel cannot exceed

10 lbs (4.5 kg) for both models.

To minimize panel weight, you may use 2" (5.08 cm) spacer strips

around the perimeter in place of full-sheet solid spacer panels.

The spacer strips must be set in at least 1" (2.54 cm) from the top,

bottom and side edges of the backer panel. If you use spacer

strips, it is also recommended that you use two 2" (5.08 cm) strips

horizontally centered for added support.

Custom Overlay Panel Dimensions

Overlay Panel

Spacer Panel

Backer Panel

5

/8" to

3

/4"

(15.88 to

19.05 mm)

1

/8"

(3.18 mm)

1

/4"

(6.35 mm)

1" minimum

(2.54 cm)

Door/Grille Trim

Spacer Panel

Offset Dimension

1

/8"

(3.18 mm)

Overlay Panel

Backer Panel

Custom Overlay Panels (36" [91.4 cm] Models) Custom Backer Panels (36" [91.4 cm] Models)

34³⁄₄"

(88.27 cm)

7¹⁄₄"

(18.42 cm)

34³⁄₄"

(88.27 cm)

34³⁄₄"

(88.27 cm)

51¹⁄₈"

(129.86 cm)

20³⁄₄"

(52.71 cm)

TOP GRILLE PANEL

Maximum Weight: 10 lbs (4.5 kg)

FREEZER DOOR PANEL

Maximum Weight: 20 lbs (9.1 kg)

REFRIGERATOR DOOR PANEL

Maximum Weight: 50 lbs (23 kg)

33³⁄₄"

(85.73 cm)

6³⁄₁₆"

(15.72 cm)

Bottom Offset

³⁄₈" (9.5 mm)

49¹⁄₈"

(124.78 cm)

20³⁄₁₆"

(51.28 cm)

34¹⁄₄"

(87.00 cm)

34¹⁄₄"

(87.00 cm)

Bottom Offset

⁷⁄₁₆" (11.1 mm)

Bottom Offset

¹⁄₄" (6.35 mm)

Center

Backer

Panel

left to

right

Center

Backer

Panel

left to

right

Center

Backer

Panel

left to

right

15

3-Piece Grille Overlay Panel Configuration 3-Piece Door Overlay Panel Configuration

1-Piece Overlay Panel Configuration

In some cases, your cabinet manufacturer may choose to work

with one panel routed for the different dimensions. Follow these

panel dimesions and placement instructions to be sure that the

custom overlay panels will fit properly.

Custom Overlay Panels (42" [106.7 cm] Models) Custom Backer Panels (42" [106.7 cm] Models)

Spacer Panels (All models)

NOTE: Spacer panels must be at least 1" (2.54 cm) from the top, bottom, and side edges of the backer panel.

40

⁷⁄₁₆

"

(102.7 cm)

20"

(50.8 cm)

20"

(50.8 cm)

40

⁷⁄₁₆

"

(102.7 cm)

7

¹⁄₄

"

(18.4 cm)

51

¹⁄₄

"

(130.2 cm)

51

¹⁄₄

"

(130.2 cm)

20

¹⁄₄

"

(51.4 cm)

TOP GRILLE PANEL

Maximum Weight: 10 lbs (4.5 kg)

FREEZER DOOR PANEL

Maximum Weight: 25 lbs (11.4 kg)

REFRIGERATOR

DOOR PANEL

Maximum Weight:

30 lbs (13.5 kg)

REFRIGERATOR

DOOR PANEL

Maximum Weight:

30 lbs (13.5 kg)

39

5

/

8"

(100.6 cm)

6

1

/

4"

(15.9 cm)

Bottom Offset

1

/

2" (1.27 cm)

49

3

/

16"

(124.93 cm)

19

7

/

8"

(50.48 cm)

19

5

/

8"

(49.85 cm)

40"

(101.6 cm)

Bottom

Offset

1

/

2"

(1.27 cm)

49

3

/

16"

(124.93 cm)

Bottom

Offset

1

/

2"

(1.27 cm)

Offset all sides

3

/

16" (4.7 mm)

Exterior

Panel

extends

above

door.

Side Offset

3

/

8" (9.5 mm)

19

5

/

8"

(49.85 cm)

Side

Offset

3

/

16"

(4.7 mm)

Side

Offset

3

/

16"

(4.7 mm)

Top View Side View

A. Offset dimension

B.

¹₄

" (6.25 mm) Backer panel

C.

¹₈

" (3.18 mm) Spacer panel

D.

³₄

" (1.92 cm) Decorative

overlay panel

1"

(2.54 cm)

D

C

B

A

A. Offset dimension

B.

¹₄

" (6.25 mm) Backer panel

C.

¹₈

" (3.18 mm) Spacer panel

D.

³₄

" (1.92 cm) Decorative overlay panel

1"

(2.54 cm)

DA C

B

16

Classic, Architect

®

, and Overlay Series

Factory Panels and Kits

(36" [91.4 cm] Models)

All factory parts are available through your KitchenAid dealer or by

calling KitchenAid Parts and Accessories at 1-800-442-9991. In

Canada, call 1-800-807-6777.

Architect

®

Series 72" (183 cm) Top Grille Panel Kit

A 72" (183 cm) wide Top Grille Panel Kit is available. This kit allows

2 units (one left-hand swing and one right-hand) to be installed

side by side with a single grille.

Extended Door Handle Kits

Use extended door handles when additional finger clearance is

needed between the door handles and custom panel. Follow the

kit instructions for installing the door handles.

Classic Series Custom Panels

(36" [91.4 cm] Models)

If you plan to install custom wood panels, you will need to create

the panels yourself or consult a qualified cabinetmaker or

carpenter. See dimension drawings for panel specifications.

IMPORTANT: Panels weighing more than recommended may

cause damage to your refrigerator.

NOTE: Dimensions shown have a (±)¹⁄₁₆" (1.5 mm) tolerance.

Panels that are more than ¹⁄₄" (6.35 mm) thick must be routed. If

panels are less than ¹⁄₄" (6.35 mm) thick, install a filler panel

between the door and the decorative panel.

Top Grille Panel

The top panel should not weigh more than 10 lbs (4.5 kg).

Refrigerator and Freezer Panels

The freezer panel should not weigh more than 20 lbs (9.1 kg). The

refrigerator panel should not weigh more than 50 lbs (22 kg).

Top Grille Panel – Routing Requirements

If the custom panels are thicker than ¹⁄₄" (6.35mm), the top and

bottom edges of the top panel should be edge routed ¹⁄₂"

(1.27 cm) and ³⁄₈" (9.5 mm), respectively. Both ends should be

edge routed ⁷⁄₈" (2.2 cm) as shown.

Color 72" (183 cm)

Stainless Steel (Architect

®

Series) #W10153554

Color Left-Hand Swing Right-Hand

Swing

White (Classic

Series)

#4396119 #8171424

Black (Classic

Series)

#4396116 #8171427

Stainless Steel

(Classic Series)

#4396118 #8171425

Matte Aluminum

Etched (Classic

Series)

#4396120 #8171423

Matte Aluminum

(Overlay Series)

#4396718

34¹⁄₂"

(87.63 cm)

7¹⁄₄"

(18.4 cm)

34¹⁄₄"

(87 cm)

34¹⁄₄"

(87 cm)

49"

(124.5 cm)

20¹⁄₈"

(51.1 cm)

¹⁄₄"

(6.35 mm)

max.

⁷⁄₈"

(2.2 cm)

Top

Grille

¹⁄₄

"

(6.35 mm)

max.

⁷⁄₈"

(2.2 cm)

Top

Grille

17

NOTE: When creating a panel with face detail, the offsets will be

hidden and must be accounted for in order to center the detail in

the top grille.

Door Panel – Routing Requirements

If the custom panels are thicker than ¹⁄₄" (6.35 mm), then all edges

of the panels must be routed. If the standard handle is used, rout

the entire handle side of both panels 3¹⁄₄" (8.25 cm) to allow for

finger clearance. Then rout the hinge side of the refrigerator panel

1" (2.54 cm). Rout both sides of the freezer panel 1" (2.54 cm).

Standard Handle – Top View

If an extended handle kit is used, rout the handle side ¹⁄₄"

(6.35 mm). All other routing dimensions would remain the same as

the standard handle. Make sure your product location will allow

doors with extended handles to be opened to 90 degrees. See

“Door Swing Dimensions.”

For more information on ordering extended handles, see “Classic

Series Factory Panels and Kits.”

NOTE: For both types of handles, rout the top and bottom edges

of the refrigerator panel ¹⁄₂" (1.27 cm). Rout the bottom of the

freezer panel ¹⁄₂" (1.27 cm).

Door Panel - Side View

Extended Handle - Top View

Classic and Architect

®

Series

Custom Side Panels

Custom side panels may be needed when not enough space is

available to have cabinets on both sides of the refrigerator or

when the refrigerator is placed and the end of a cabinet run. You

may choose an Inset, Flush, or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of

installation you are planning.

NOTES:

■ The dimensions shown are actual product dimensions and

may not reflect the needed panel installation dimensions.

■ The side panel should be a minimum of ¹⁄₂" (1.27 cm) thick

to avoid warping.

■ If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on the rear wall.

Refrigerator

¹⁄₂"

(1.3 cm)

min.

¹⁄₄"

(6.35 mm) max.

Top

Bottom

³⁄₈"

(9.5 mm)

min.

¹⁄₄"

(6.35 mm) max.

Center face

detail between

offsets

2" (5 cm)

min.

¹⁄₄" (6.35 mm) max.

3¹⁄₄"

(8.25 cm)

min.

Door

Panel

Handle

1"

(2.54 cm)

Door

Panel

Hinge Side

¹⁄₂" (1.3 cm)

min.

¹⁄₄"

(6.35 mm)

max.

Panel

¹⁄₄"

(6.35 mm)

Door

Panel

Handle

1"

(2.54 cm)

Door

Panel

Hinge Side

1"

(2.54 cm)

max

24¹⁄₈"

(61.3 cm)

23

¹⁄₂"

(59.7 cm)

23¹¹⁄₁₆"

(60.3 cm)

18

Side Trim

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add ⁷⁄₃₂" (5.6 mm) to this measurement to allow the side

panel to fit into the trim.

2. If the panel is more than ¹⁄₄" (6.35 mm) thick, rout the front

edge to allow the side panel to fit into the trim.

Flush Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall.

2. Attach the support board with a screw or adhesive that is

compatible with aluminum and wood.

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to back wall.

2. Rout the front edge of the support board or attach a ¹⁄₄"

(6.35 mm) board to hold the panel in the cabinet side trim.

Overlay Series Custom Side Panels

Custom side panels may be needed when not enough space is

available to have cabinets on both sides of the refrigerator or

when the refrigerator is placed and the end of a cabinet run. You

may choose an Inset or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of

installation you are planning.

NOTES:

■ The dimensions shown are actual product dimensions and

may not reflect the needed installation dimensions.

■ The side panel should be a minimum of ¹⁄₂" (1.27 cm) thick

to avoid warping.

■ If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on the rear wall.

Refrigerator (36" [91.4 cm] Models)

¹¹⁄₆₄"

(4.5 mm)

¹⁄₄"

(6.35 mm)

³⁄₁₆"

(4.7 mm)

⁷⁄₃₂"

(5.5 mm)

¹³⁄₃₂" (10 mm)

⁵⁄₈"

(15.7 mm)

A

23¹¹⁄₁₆"

(60.16 cm)

Overlay

19

Refrigerator (42" [106.7 cm] Models)

Side Trim (36" [91.4 cm] Models)

Side Trim (42" [106.7 cm] Models)

Inset Installation Dimensions

36" [91.4 cm] Models

1. Measure the distance from point A (as shown) to the back

wall. Add ¹⁄₃₂" (0.8 mm) to this measurement to allow the side

panel to fit into the trim.

2. If the panel is more than ³⁄₈" (9.5 mm) thick, rout the front edge

to allow the side panel to fit into the trim

42" [106.7 cm] Models

1. Measure the distance from point A (as shown) to the back

wall. Add ¹⁄₃₂" (0.8 mm) to this measurement to allow the side

panel to fit into the trim.

2. If the panel is more than ³⁄₈" (9.5 mm) thick, rout the front edge

to allow the side panel to fit into the trim

Recessed Inset Installation Dimensions

36" [91.4 cm] Models

1. Measure the distance from point A (as shown) to back wall.

2. Rout the front edge of the support board or attach a ³⁄₈"

(9.5 mm) board to hold the panel in the cabinet side trim.

42" [106.7 cm] Models

1. Measure the distance from point A (as shown) to back wall.

2. Rout the front edge of the support board or attach a ³⁄₈"

(9.5 mm) board to hold the panel in the cabinet side trim.

23³⁄₈"

(59.40 cm)

Overlay

³⁄₁₆"

(4.5 mm)

³⁄₈"

(9.7 mm)

¹⁄₁₆"

(1.5 mm)

³⁄₃₂"

(2.38 mm)

³⁄₁₆"

(4.5 mm)

³⁄₈"

(9.7 mm)

¹⁄₁₆"

(1.5 mm)

¹⁄₈"

(3.2 mm)

A

20

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

IMPORTANT:

■ Do not remove the film covering until the refrigerator is in its

operating location.

■ All four leveling legs must contact the floor to support and

stabilize the full weight of the refrigerator.

■ Keep the cardboard shipping piece or plywood under the

refrigerator until it is installed in the operating location.

1. Remove and save the literature package bag taped to the side

of the refrigerator and the parts bag behind the grille. Remove

the four brackets (two on each side) that attach the shipping

base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the

refrigerator is in its final location.

2. If necessary, reduce the tipping radius. See “Tipping Radius”

for ceiling height requirements or “Reduce Tipping Radius” for

step-by-step instructions. If you do not need to reduce the

tipping radius, proceed to “Move the Refrigerator into House.”

Reduce Tipping Radius

(if required)

Before bringing the refrigerator into the home, be sure there is

adequate ceiling height to stand the refrigerator upright. See

“Tipping Radius” in the “Installation Requirements” section for

more information.

If you do not have adequate ceiling height to stand the refrigerator

upright, the tipping radius can be reduced by removing the top

grille and side trims (see the following chart).

1. Grasp both ends of the top grille.

2. Push the top grille straight up; then pull straight out. Lay the

grille on a soft surface.

3. Remove the six screws attaching each cabinet side trim to the

refrigerator and remove the side trims.

Move the Refrigerator into House

1. Place an appliance dolly under the left side of the refrigerator

as shown. Place the corner posts from the packing materials

over the trims and handles as appropriate to avoid damage.

Slowly tighten the strap.

NOTE: Pass the dolly strap under the handles.

36" (91.4 cm) Models

Model Reduced Tipping Radius

36 88" (223.5 cm)

42 88¹⁄₂" (224.8 cm)

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

A. Top grille

B. Cabinet side trim

B BA

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

La page charge ...

KitchenAid KBLC36FTS - 36" Bottom-Freezer Refrigerator Guide d'installation

KitchenAid KBLC36FTS - 36" Bottom-Freezer Refrigerator Guide d'installation

dans d''autres langues

Documents connexes

Autres documents