Toro Flex-Force Power System 41cm (16in) 60V MAX Chainsaw Manuel utilisateur

Form No. 3460-237 Rev A

Flex-Force Power System™ 41cm (16in) 60V

MAX Chainsaw

51851

Motosierra 60 V MAX de 41 cm (16") con

Flex-Force Power System™51851

T ronçonneuse Flex-Force Power System™

41 cm (16 po) 60 V MAX51851

www .T oro.com.

*3460-237*

Form No. 3460-234 Rev A

Flex-Force Power System

™

41cm

(16in) 60V MAX Chainsaw

Model No. 51851 —Serial No. 323000001 and Up

Register at www .T oro.com.

Original Instructions (EN)

*3460-234*

For assistance, please see

www .T oro.com/support

for instructional videos

or contact 1-888-384-9939

before returning this

product.

W ARNING

CALIFORNIA

Proposition 65 W arning

The power cord on this product contains

lead, a chemical known to the State

of California to cause birth defects

or other reproductive harm. W ash

hands after handling.

Use of this product may cause exposure

to chemicals known to the State of

California to cause cancer , birth defects,

or other reproductive harm.

Introduction

his chain saw is designed for cutting tree branches,

logs, and wooden beams of a diameter no longer than

the cutting length of the guide bar . It is to be used only

by adults. It is designed to use T oro 60V lithium-ion

battery packs. These battery packs are designed

to be charged only by T oro 60V lithium-ion battery

chargers. Using these products for purposes other

than their intended use could prove dangerous to you

and bystanders. Using these products for purposes

other than their intended use could prove dangerous

to you and bystanders.

Read this information carefully to learn how to operate

and maintain your product properly and to avoid

injury and product damage. Y ou are responsible for

operating the product properly and safely .

V isit www .T oro.com for more information, including

safety tips, training materials, accessory information,

help nding a dealer , or to register your product.

Whenever you need service, genuine T oro parts, or

additional information, contact an Authorized Service

Dealer or T oro Customer Service and have the model

and serial numbers of your product ready . Figure 1

identies the location of the model and serial numbers

on the product. W rite the numbers in the space

provided.

Important: W ith your mobile device, you can

scan the QR code (if equipped) on the serial

number plate to access warranty , parts, and other

product information.

g425184

Figure 1

1. Model and serial number location.

Model No.

Serial No.

81 1 1 L yndale A venue South

Bloomington, MN 55420

2

Contact us at www .T oro.com.

Printed in China

Safety-Alert Symbol

The safety-alert symbol ( Figure 2 ) shown in this

manual and on the machine identies important safety

messages that you must follow to prevent accidents.

g000502

Figure 2

Safety-alert symbol

The safety-alert symbol appears above information

that alerts you to unsafe actions or situations and

is followed by the word DANGER ,W ARNING , or

CAUTION .

DANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious

injury .

W ARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury .

CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury .

This manual uses two other words to highlight

information. Important calls attention to special

mechanical information and Note emphasizes general

information worthy of special attention.

Contents

Safety-Alert Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety ....................................................................... 4

........................................................................... 4

........................................................................... 6

Personal Protective Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Setup ...................................................................... 10

Filling the Chain Saw with Bar and Chain

Oil ................................................................. 10

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1

Attachments/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1

Before Using the Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1

Starting the Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Shutting Of f the Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Cutting with the Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Pruning a T ree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Felling a T ree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Limbing a Fallen T ree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Bucking a Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Installing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Charging the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Recommended Maintenance Schedule(s) . . . . . . . . . . . 20

Checking the Oil Level and Adding Bar and

Chain Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Checking the Chain Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Checking the Flow of Bar and Chain

Oil ................................................................. 21

Adjusting the Chain T ension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Servicing the Guide Bar , Chain, and Drive

Sprocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Installing the Guide Bar and Chain . . . . . . . . . . . . . . . . . . . . 24

Sharpening the Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Preparing the Battery Pack for

Recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3

Safety

W ARNING

Read all safety warnings, instructions,

illustrations and specications provided with

this power tool.

Failure to follow all instructions listed below

may result in electric shock, re and/or

serious injury .

Save all warnings and instructions for future

reference.

The term “power tool” in all the warnings refers

to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

IMPORT ANT SAFETY

INSTRUCTIONS

I. W ork area safety

1. Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of

ammable liquids, gases, or dust. Power

tools create sparks which may ignite the dust

or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

II. Electrical safety

1. Power tool plugs must match the outlet.

Never modify the plug in any way . Do not use

any adapter plugs with earthed (grounded)

power tools. Unmodied plugs and matching

outlets will reduce risk of electric shock.

2. A void body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges

and refrigerators. There is an increased risk

of electric shock if your body is earthed or

grounded.

3. Do not expose power tools to rain or wet

conditions. W ater entering a power tool will

increase the risk of electric shock.

4. Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

5. When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

6. If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply . Use of an RCD

reduces the risk of electric shock.

III. Personal safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inuence of drugs, alcohol, or

medication. A moment of inattention while

operating power tools may result in serious

personal injury .

2. Use personal protective equipment. Always

wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate

conditions reduces personal injuries.

3. Prevent unintentional starting. Ensure

the switch is in the O FF -position before

connecting to power source and/or battery

pack, picking up or carrying the tool. Carrying

power tools with your nger on the switch or

energizing power tools that have the switch on

invites accidents.

4. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury .

5. Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

6. Dress properly . Do not wear loose clothing

or jewelry . Keep your hair and clothing away

from moving parts. Loose clothes, jewelry , or

long hair can be caught in moving parts.

7. If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce

dust-related hazards.

8. Do not let familiarity gained from frequent

use of tools allow you to become complacent

and ignore tool safety principles. A careless

action can cause severe injury within a fraction

of a second.

4

IV . Power tool use and care

1. Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

2. Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

3. Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any

adjustments, changing accessories, or

storing power tools. Such preventive safety

measures reduce the risk of starting the power

tool accidentally .

4. Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions

to operate the power tool. Power tools are

dangerous in the hands of untrained users.

5. Maintain power tools and accessories.

Check for misalignment or binding of moving

parts, breakage of parts, and any other

condition that may affect the power tool’ s

operation. If damaged, have the power tool

repaired before use. Many accidents are

caused by poorly maintained power tools.

6. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

7. Use the power tool, accessories, and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations different from those

intended could result in a hazardous situation.

8. Keep handles and grasping surfaces dry ,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow

for safe handling and control of the tool in

unexpected situations.

V . Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer . A charger that is suitable for

one type of battery pack may create a risk of re

when used with another battery pack.

2. Use power tools only with specically

designated battery packs. Use of any other

battery packs may create a risk of injury and re.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small

metal objects, that can make a connection

from one terminal to another . Shorting the

battery terminals together may cause burns or

a re.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ush with water .

If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery

may cause irritation or burns.

5. Do not use a battery pack or tool that is

damaged or modied. Damaged or modied

batteries may exhibit unpredictable behavior

resulting in re, explosion or risk of injury .

6. Do not expose a battery pack or tool to re

or excessive temperature. Exposure to re or

temperature above 130 °C (265 °F) may cause

explosion.

7. Follow all charging instructions and do

not charge the battery pack or tool outside

the temperature range specied in the

instructions. Charging improperly or at

temperatures outside the specied range may

damage the battery and increase the risk of re.

VI. Service

1. Have your power tool serviced by a

qualied repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

2. Never service damaged battery packs.

Service of battery packs should only be

performed by the manufacturer or authorized

service providers.

5

VII. Chain saw safety

1. Keep all parts of the body away from the

saw chain when the chain saw is operating.

Before you start the chain saw , make sure

the saw chain is not contacting anything.

A moment of inattention while operating chain

saws may cause entanglement of your clothing

or body with the saw chain.

2. Always hold the chain saw with your right

hand on the rear handle and your left hand

on the front handle. Holding the chain saw with

a reversed hand conguration increases the risk

of personal injury and should never be done.

3. Hold the chain saw by insulated gripping

surfaces only , because the saw chain may

contact hidden wiring. Saw chains contacting

a "live" wire may make exposed metal parts of

the chain saw "live'" and could give the operator

an electric shock.

4. W ear eye protection. Further protective

equipment for hearing, head, hands, legs and

feet is recommended. Adequate protective

equipment will reduce personal injury from ying

debris or accidental contact with the saw chain.

5. Do not operate a chain saw in a tree, on

a ladder , from a rooftop, or any unstable

support. Operation of a chain saw in this

manner could result in serious personal injury .

6. Always keep proper footing and operate

the chain saw only when standing on xed,

secure and level surface. Slippery or unstable

surfaces such as ladders may cause a loss of

balance or control of the chain saw .

7. When cutting a limb that is under tension, be

alert for spring back. When the tension in the

wood bers is released, the spring loaded limb

may strike the operator and/or throw the chain

saw out of control.

8. Use extreme caution when cutting brush and

saplings. The slender material may catch the

saw chain and be whipped toward you or pull

you off balance.

9. Carry the chain saw by the front handle with

the chain saw switched off and away from

your body . When transporting or storing the

chain saw , always t the guide bar cover and

remove the battery . Proper handling of the

chain saw will reduce the likelihood of accidental

contact with the moving saw chain.

10. Follow instructions for lubricating, chain

tensioning, and changing the bar and chain.

Improperly tensioned or lubricated chain may

either break or increase the chance for kickback.

1 1. Cut wood only . Do not use chain saw for

purposes not intended. For example: do

not use chain saw for cutting metal, plastic,

masonry or non-wood building materials.

Use of the chain saw for operations different than

intended could result in a hazardous situation.

12. Do not attempt to fell a tree until you have an

understanding of the risks and how to avoid

them. Serious injury could occur to the operator

or bystanders while felling a tree.

13. Follow all instructions when clearing jammed

material, storing or servicing the chain saw .

Make sure the switch is off and the battery

pack is removed. Unexpected actuation of

the machine while clearing jammed material or

servicing may result in serious personal injury .

6

14. Causes and operator prevention of kickback.

Kickback may occur when the nose or tip of the

guide bar touches an object, or when the wood

closes in and pinches the saw chain in the cut.

T ip contact in some cases may cause a sudden

reverse reaction, kicking the guide bar up and

back towards the operator .

Pinching the saw chain along the top of the

guide bar may push the guide bar rapidly back

towards the operator .

Either of these reactions may cause you to lose

control of the saw , which could result in serious

personal injury . Do not rely exclusively upon the

safety devices built into your saw . As a chain

saw user , you should take several steps to keep

your cutting jobs free from accident or injury .

Kickback is the result of chain saw misuse and/or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below:

A. Maintain a rm grip, with thumbs and

ngers encircling the chain saw handles,

with both hands on the saw and position

your body and arm to allow you to resist

kickback forces. Kickback forces can

be controlled by the operator , if proper

precautions are taken. Do not let go of the

chain saw .

B. Do not overreach and do not cut above

shoulder height. This helps prevent

unintended tip contact and enables better

control of the chain saw in unexpected

situations.

C. Only use replacement guide bars

and saw chains specied by the

manufacturer . Incorrect replacement guide

bars and saw chains may cause chain

breakage and/or kickback.

D. Follow the manufacturer ’ s sharpening

and maintenance instructions for the

saw chain. Decreasing the depth gauge

height can lead to increased kickback.

SA VE THESE

INSTRUCTIONS

Personal Protective

Equipment

g316566

Figure 3

1. W ear a hard hat in

situations where debris

may contact the head.

4. W ear gloves

2. W ear hearing protection 5. W ear protective pants or

chaps

3. W ear safety glasses

and/or a face shield

6. W ear substantial,

slip-resistant footwear

7

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger . Replace any decal that is damaged or missing.

decal144-3094

144-3094

1. The battery pack is

charging.

3. The battery pack is over

or under the appropriate

temperature range.

2. The battery pack is fully

charged.

4. Battery pack charging fault

decal144-3098

144-3098

decal144-3096

144-3096

decal144-3090

144-3090

decal145-8271

145-8271

8

decal140-8475

140-8475

1. Read the Operator ’ s

Manual .

3. Keep away from open re

or ames.

2. Call2Recycle® battery

recycling program

4. Do not expose to rain.

decal137-9461

137-9461

1. Battery charge status

decal145-8273

145-8273

1. Cutting hazard of hand.

7. Do no expose to rain.

2. Stay away from moving parts. 8. Read the Operator ’ s Manual .

3. Keep all guards and shields in place. 9. W ear hearing protection.

4. Kickback hazard 10. W ear eye protection.

5. Do not contact objects with the guide bar tip. 1 1. Always use 2 hands when operating the chain saw .

6. Do not operate the chain saw holding it with one hand only .

9

Setup

Important: The battery pack is not fully charged

when it is purchased. Before using the machine

for the rst time, refer to Charging the Battery

Pack ( page 19 ) .

Filling the Chain Saw with

Bar and Chain Oil

Important: Use only bar and chain oil (sold

separately).

Fill the chain saw with bar and chain oil; refer to

Checking the Oil Level and Adding Bar and Chain

Oil ( page 20 ) .

Product Overview

g315699

Figure 4

Left side shown

1. Chain

6. Battery pack

2. Guide bar

7. Button latch

3. Oil window

8. T rigger lock

4. Oil cap

9. T rigger

5. Front handle 10. Bucking teeth

g315700

Figure 5

Right side shown

1. Chain brake 4. Multitool (located beneath

rear handle)

2. Side cover 5. Chain tensioning screw

3. Captive cover nut 6. Guide bar cover

g330065

Figure 6

1. Battery charger Model

88610 (included with

Model 51851)

2. Battery pack Model 88620

(included with Model

51851)

10

Specications

Model

51851/51851T

Bar Length (with 88613 and

88614 equipped)

40.6 cm (16 inches)

Chain Gauge (with 88613

and 88614 equipped)

0.043 inches

Chain Pitch (with 88613 and

88614 equipped)

3/8 inch

Chain Length (with 88613

and 88614 equipped)

56 links

Rated V oltage

60V DC maximum, 54 VDC

nominal usage

W eight (without a battery) 4.35 kg (9.59 lb)

Charger T ype

T oro 60V lithium-ion chargers

Battery T ype T oro 60V lithum-ion batteries

Appropriate T emperature Ranges

Charge/store the battery pack

at

5°C (41°F) to 40°C (104°F)*

Use the battery pack at

-30°C (-22°F) to 49°C (120°F)*

Use the tool at

0°C (32°F) to 49°C (120°F)*

*Charging time will increase if you do not charge the

battery within this range.

Store the tool, battery pack, and battery charger in an

enclosed clean, dry area.

Attachments/Accessories

A selection of T oro approved attachments and

accessories is available for use with the machine

to enhance and expand its capabilities. Contact

your Authorized Service Dealer or authorized T oro

distributor or go to www .T oro.com for a list of all

approved attachments and accessories.

T o ensure optimum performance and continued safety

certication of the machine, use only genuine T oro

replacement parts and accessories. Replacement

parts and accessories made by other manufacturers

could be dangerous.

Operation

Before Using the Chain Saw

Before using the chain saw , do the following:

•Check the chain tension; refer to Adjusting the

Chain T ension ( page 22 ) .

•Clean the chain saw components, inspect them for

excessive wear or damage, and replace them as

needed; refer to Servicing the Guide Bar , Chain,

and Drive Sprocket ( page 23 ) .

•Check the chain for sharpness and damage, and

sharpen or replace as needed; refer to Sharpening

the Chain ( page 24 ) .

•Check the oil level; refer to Checking the Oil Level

and Adding Bar and Chain Oil ( page 20 ) .

•Check the chain brake; refer to Checking the

Chain Brake ( page 21 ) .

•Check the chain saw for damage, general

appearance, and performance; ensure that the

switches move freely , the vents and handles are

clean, and the bar is not bent or damaged.

1 1

Starting the Chain Saw

1. Ensure that the vents on the chain saw are free

from dust and debris ( Figure 7 ).

g315701

Figure 7

1. Side vent

2. Bottom vent

2. Set the chain saw down on a level surface.

3. Align the tongue of the battery pack with the

battery cavity in the chain saw ( Figure 8 ).

g315702

Figure 8

4. Push the battery pack into the battery cavity until

the battery pack locks into place.

5. Remove the protective cover from the chain.

6. Ensure that the chain brake is in the O PERATING

position ( Figure 9 ).

g315703

Figure 9

1. Chain brake ( O PERATING

position)

2. Chain brake ( STOP

position)

7. With your left hand on the front handle and your

right hand on the rear handle, press the trigger

lock, then squeeze the trigger ( Figure 10 ).

g315704

Figure 10

1. Front handle 4. T rigger

2. Chain brake

5. Rear handle

3. T rigger lock

Shutting Off the Chain Saw

T o shut of f the chain saw , release the trigger .

Whenever you are not using the saw or are

transporting the saw to or from the work area, move

the chain brake to the S TOP position ( Figure 9 ) and

remove the battery pack.

12

Cutting with the Chain Saw

W ARNING

Operating a chain saw improperly can cause

serious personal injury or death.

Read and follow all operating instructions

carefully to avoid possible personal injury .

W ARNING

Kickback can cause serious or fatal injury to

you.

Always ensure that the chain brake system

is working properly before you operate the

chain saw .

A void touching objects to be cut with the

nose of the chain saw guide bar .

There are 2 types of kickback:

•A fast upward motion of the chain saw that results

when the chain at the nose or top of the bar

contacts an object

•A fast backward motion of the chain saw that

results when the chain at the nose or top of the bar

is pinched by the object being cut

Figure 1 1 shows the area of the bar to avoid contacting

an object to prevent kickback.

g318677

Figure 1 1

1. Kickback area (nose, top

of the bar)

2. Nose

1. Grip the chain saw with 2 hands, with your left

hand on the front handle and your right hand on

the rear handle as shown in Figure 12 .

Important: Keep your left arm straight with

your elbow locked to help reduce kickback.

g025213

Figure 12

2. Stand on solid, even ground in front of the wood

to be cut.

3. Stand to the left side of the chain saw , not in

line with the chain , and position yourself for

balanced, stable footing while cutting.

Important: Do not stand on the wood that

you are cutting.

4. Ensure that you only cut the wood that you

intend to cut; do not allow the saw chain to

contact the earth, other logs, or any other

objects when cutting.

5. Ensure that the saw chain is rotating at full

speed before starting a cut.

6. Cut with the wood near the rear of the guide bar ,

close to the bucking teeth; press the chain saw

lightly against the wood and allow the weight of

the chain saw to drive the cutting.

Note: Y ou can use the bucking teeth ( Figure

13 ) to apply light pressure.

g315747

Figure 13

1. Bucking teeth

7. Keep steady pressure on the chain saw , cutting

in a straight line, and release pressure only near

the end of the cut.

13

Pruning a T ree

W ARNING

Cutting higher limbs from a tree off the ground

can put you in an unstable position that could

be unsafe for you while handling a chain saw ,

resulting in possible serious personal injury

or death to you or bystanders.

When cutting limbs from a standing tree, use

the following practices:

• Do not climb on limbs or branches with a

chain saw .

• Do not overreach, and cut with both hands

on the chain saw .

• Ensure that all bystanders are away from

the area where branches may fall.

1. Grip the chain saw as shown in Figure 12 .

2. While cutting small branches, apply light

pressure to the branch to be cut.

3. While cutting larger branches, make a shallow

undercut and then complete the cut from the

topside of the branch.

A. Cut from the underside of the limb about 15

cm (6 inches) from the trunk. Cut a third of

the way through the limb.

B. Cut 5.0 to 10.0 cm (2 to 4 inches) farther

out on the limb and from above. Cut the

limb until it falls.

C. Cut the limb stub at the branch collar

(Figure 14 ).

Important: Do not cut the limb past the

collar , ush to the trunk, or leave a large

limb stub; this damages the tree.

g316577

Figure 14

1. First relief undercut

3. Final pruning cut to

remove the limb stub

2. Second through cut 4. Branch collar (where the

trunk transitions to the

limb)

Felling a T ree

W ARNING

Cutting standing trees requires expertise and

poses hazards.

• Before attempting to cut a big tree, practice

cutting a few branches, limbs, or small logs

to familiarize yourself with the chain saw .

• Do not use this chain saw to fell large trees

with a diameter larger than the length of

the guide bar .

DANGER

Loose or tangled limbs above you may be

dislodged by vibration from cutting, causing

severe injury or death.

Always look overhead for loose and tangled

limbs before cutting; if you see any loose

limbs or branches, remove them before

cutting.

The proper operator stance for felling a tree is shown

in Figure 15 .

14

g195831

Figure 15

1. Determine the direction that the tree will fall.

T ake the following variables into consideration:

•Wind direction

•Heavier limbs on 1 side of the tree

•Natural tilt of the tree (if any)

2. Determine a clear , safe retreat path away from

the danger area; refer to Figure 16 .

g024800

Figure 16

1. Retreat path (at a 45°

angle opposite from the

planned direction of fall)

3. Danger area

2. Planned direction of fall

3. Grip the chain saw as shown in ( Figure 12 ).

4. Make the rst cut a third of the way through the

tree diameter on the side where you want the

tree to fall ( Figure 17 ).

Note: Making this cut prevents the chain saw

from being pinched while making the next cut.

g228707

Figure 17

1. First cut 3. Hinge

2. Second cut

4. Back cut

5. Make a second cut to form a notch, starting the

cut at least 5 cm (2 inches) above and away

from the rst cut ( Figure 17 ).

Important: Ensure that the rst cut and the

second cut meet at the same point, forming

a clean notch.

6. Make the back cut from the opposite side of the

notch and about 5 cm (2 inches) higher than the

bottom of the notch as shown in Figure 17 .

Important: Stop the third cut 2.5 to 5.0 cm

(1 to 2 inches) from the notch to form a hinge

between the cuts ( Figure 17 ), which keeps

the tree from falling in the wrong direction

or twisting as it falls.

Note: As the back cut nears the hinge ( Figure

17 ), the tree should begin to fall.

7. When the tree begins to fall, remove the chain

saw , shut it of f, put it down, and retreat along the

path you determined in step 2.

Important: If the tree begins to fall in an

undesired direction, immediately stop the

cut, shut off the chain saw , put the chain saw

down, and use a non-metallic wedge to open

the back cut and push the tree in the desired

direction.

15

Limbing a Fallen T ree

1. Grip the chain saw as shown in Figure 12 .

2. Moving from the base of the tree up, cut of f the smaller limbs from the tree that are not supporting its

weight of f the ground ( Figure 18 ).

3. Cut the larger limbs that support the weight of the tree from the bottom upward so that the limbs do

not pinch the saw blade ( Figure 19 ).

g316601

Figure 18

g315751

Figure 19

16

Bucking a Log

When bucking a log, note where the log is supported

and where there is a load on the log. Cut the log so

that when the ends fall, your guide bar will not be

pinched between them.

Important: If the chain saw binds in the cut, do

not attempt to free it by running the motor . Shut

off the saw , remove the battery , then use a wedge

to pry open the cut and release the saw .

If you are cutting branches from a fallen tree or cutting

a log into lengths, support the log of f the ground

(preferably on a sawbuck).

•If the log is supported on both ends, but not in the

middle, the load is on the center of the log.

– Start from the top and cut about a third of the

way through the log ( Figure 20 A).

– Make a second cut from the underside to meet

the rst cut ( Figure 20 B). This keeps the log

from pinching the saw .

g315765

Figure 20

•If the log is supported on a single end, the load is

on the free end of the log.

– Start from the underside and cut about a third

of the way through the log.

– Make a second cut from the top to meet the rst

cut. This keeps the log from pinching the saw .

•If the log is supported of f the ground along its entire

length, without a heavy load on the log at any

point, cut all the way through the log from the top.

•If the log is on a hill, always stand on the uphill

side of the log ( Figure 21 ).

g315767

Figure 21

1. Direction of slope

•If the whole length of the log is supported on at,

level ground, cut a third of the diameter from the

top, then roll the log over and make another cut to

meet the rst cut ( Figure 22 ).

g315766

Figure 22

17

Installing the Battery Pack

Important: Use the battery pack only in

temperatures that are within the appropriate

range; refer to Specications ( page 1 1 ) .

1. Set the chain saw down on a level surface.

2. Align the tongue of the battery pack with the

battery cavity in the chain saw ( Figure 23 ).

g315702

Figure 23

3. Push the battery pack into the battery cavity until

the battery pack locks into place.

Removing the Battery Pack

1. Place the chain saw on a at surface.

2. Press down on the latch and remove the battery

pack from the cavity .

g315763

Figure 24

1. Latch

18

La page charge ...

Toro Flex-Force Power System 41cm (16in) 60V MAX Chainsaw Manuel utilisateur

Toro Flex-Force Power System 41cm (16in) 60V MAX Chainsaw Manuel utilisateur

dans d''autres langues

Documents connexes