Honeywell RTH6580WF1001/U1 Manuel utilisateur

User Guide

Read and save these

instructions.

For help please visit

honeywellhome.com

RTH6500WF

Smart Series

RTH65801006

Programmable

Thermostat

HOLD

M37771

In the box you will find

• Thermostat

• Wallplate (attached to

thermostat)

• Screws and anchors

• Quick Start Guide

• Thermostat ID Card

• Wire labels

• User Guide

• Quick Reference Card

Find rebates: HoneywellHome.com/Rebates

Input: 24 V~ @ 60 Hz, 1.0 A

69-2715EF—07 ii

Welcome

Congratulations on your purchase of a Smart

programmable thermostat. When registered

to Total Connect Comfort, you can remotely

monitor and control the heating and cooling

system in your home or business—you can

stay connected to your comfort system

wherever you go.

Total Connect Comfort is the perfect solution

if you travel frequently, own a vacation

home, a business or manage an Investment

property or if you are simply looking for peace

of mind.

This thermostat works with common 24 volt systems such as forced air, hydronic,

heat pump, oil, gas, and electric. It will not work with millivolt systems, such as a

gas fireplace, or with 120/240 volt systems such as baseboard electric heat.

MERCURY NOTICE: Do not place your old thermostat in the trash if it contains

mercury in a sealed tube. Contact the Thermostat Recycling Corporation at

www.thermostat-recycle.org or 18002388192 for information on how and

where to properly and safely dispose of your old thermostat.

NOTICE: To avoid possible compressor damage, do not run air conditioner if the

outside temperature drops below 50°F (10°C).

Need help?

Visit honeywellhome.com for assistance before returning the thermostat to the store.

Precautions and Warnings

1 69-2715EF—07

About your new thermostat

Controls and Home screen

quick reference ....................................................... 2

Preset energy-saving schedules ................... 2

Installation

Installing your thermostat ................................ 3

Connecting to your WiFi network ............. 10

Registering your thermostat online .......... 12

Operation

Setting the the time and day ........................ 14

Setting the fan ..................................................... 14

Selecting system mode ................................... 14

Adjusting program schedules ...................... 15

Overriding schedules temporarily ............. 15

Overriding schedules permanently ........... 15

Unregistering thermostat .............................. 16

Disconnecting WiFi ......................................... 16

Special features................................................... 17

Setting functions and options ..................... 18

Appendices

Frequently asked questions .......................... 20

Troubleshooting .................................................. 21

Limited warranty ................................................. 24

Table of contents

Features of your thermostat

With your new thermostat, you can:

• Connect to the Internet to monitor and control your heating/cooling system

• View and change your heating/cooling system settings

• View and set temperature and schedules

• Receive alerts via email and get automatic upgrades

Your new thermostat provides:

• Smart Response Technology

• Compressor protection

• Heat/cool auto changeover

69-2715EF—07 2

M31586

HOLD

Controls and home screen quick reference

Once your thermostat is installed, it will display the home screen. Portions of this

display will change depending on how you are viewing it.

The screen lights when you press any button. It stays lit for 8 seconds after you

complete changes.

Set up messages

describe steps in the

WiFi set up process

WiFi status

Set clock, day,

or schedule

Select fan

settings

Additional

settings

Temperature

adjustment buttons

Permanent override

button

Select system

mode

Preset energy-saving schedules

This thermostat is pre-set with energy-saving program settings for four time periods.

Using the default settings can reduce your heating/cooling expenses if used as

directed. Savings may vary depending on geographic region and usage. To change the

settings, see pages 15.

Default Heat Settings Default Cool Settings

WAKE

6:00 am

70

°

78

°

LEAVE

8:00 am

62

°

85

°

RETURN

6:00 pm

70

°

78

°

SLEEP

10:00 pm

62

°

82

°

3 69-2715EF—07

Setting up your thermostat

Setting up your programmable thermostat is easy. It is preprogrammed and ready to go

as soon as it is installed and registered.

Install your thermostat.

Connect your home WiFi network.

Register online for remote access.

Before you begin, you may want to watch a brief installation video. Use

the QR Code

®

at the front of this guide, or go to

honeywellhome.com/support

2

3

1

Installing your thermostat

You might need the following tools to install this thermostat:

• No. 2 Phillips screwdriver

• Small pocket screwdriver

• Pencil

• Level (optional)

• Drill and bits (3/16” for drywall,

7/32” for plaster) (optional)

• Hammer (optional)

• Electrical tape (optional)

1 Switch OFF power to your

heating/cooling system.

Important! To protect your

equipment, switch OFF the power to

your heating/cooling system at the

breaker box or the system switch.

or

M31535

Circuit

breaker box

Heating/cooling

system power

switch

69-2715EF—07 4

C

MCR33823

If you have an older thermostat with

a sealed mercury tube, turn to page

ii for proper disposal instructions.

Installing your thermostat

2 Remove old thermostat faceplate

and leave wires connected.

2a Take a picture of the wire

connections for later reference.

2b If no wire is connected to a

terminal labeled C or no C

terminal exists on the old

thermostat, view the Alternate

Wiring videos at

honeywellhome.com/wifi-thermostat

Terminal

designation

Important! C wire is required and is

the primary power source for your

thermostat. Without a C wire, your

thermostat will not power up.

3 Label wires.

Do not label by wire color. Use

the supplied sticky tags to label

each wire as you disconnect it.

Label wires according to the old

thermostat terminal designations,

not by wire color.

Note: If no tag matches a wire

terminal label, write the terminal

label on a blank tag.

4 Remove wallplate.

Remove the old wallplate from

the wall after all wires have been

labeled and disconnected.

Terminal

designation

C

MCR31537

Blank sticky

tags

Sticky tags

5 Separate thermostat and its

wallplate.

On your new thermostat, grasp the

finger holds on the top and bottom

of the wallplate with one hand and

the thermostat (front) with the other

hand. Pull pieces apart.

Thermostat

Wallplate (back view)

Finger holds

M33856

PULL HERE

TO REMOVE

PULL HERE

TO REMOVE

5 69-2715EF—07

Installing your thermostat

6 Mount wallplate for thermostat.

Mount your new wallplate using screws and

anchors included with the thermostat.

If necessary:

Drill 3/16-in holes for drywall.

Drill 7/32-in holes for plaster.

Note: You may be able to use your existing wall

anchors. Hold the wallplate up to the existing

anchors to check for alignment

Wallplate

MCR33857

Important! The thermostat requires a C wire to operate. The C, or common, wire

brings 24 VAC power to the thermostat. Many older mechanical or battery operated

thermostats do not require a C wire. If you don’t have a C wire, try:

• Looking for an unused wire that is pushed into the wall. Connect that wire to C and

check that it is connected to the 24 VAC common at your heating/cooling system.

Note: Not all heating/cooling systems label the 24 VAC common C. Check your system

manual or contact the manufacturer to find out which terminal is the 24 VAC common.

View the Alternate Wiring videos at honeywellhome.com/wifi-thermostat

Wiring

For conventional heating/cooling systems (natural gas, oil or electric furnace, air

conditioner), see page 5. See “Glossary” on page 23 for further definition.

For a heat pump system, see page 7. See “Glossary” on page 23 for further

definition.

Wiring (conventional system)

7A Wire the thermostat to your conventional system.

a Starting with the C Wire, match the sticky tag on

the wire to the terminal labels.

You must have a C wire.

b Loosen screw, insert wire on inside edge

of terminal, then tighten screw.

c Verify wire is firmly secured by gently

pulling on wire.

d Repeat steps a–c for all other wires.

e Push any excess wire back into the wall

opening after all wires are installed.

f Continue to page 8.

Labels don’t match? See alternate

wiring key on pages 6.

W2

G W

YR RCK

Y2

C

MCR33878

Y

HEAT PUMP

CONVENTIONAL

AUX/E

G O/B

YRRCK

L

C

G

W

R

Remove metal jumper

only if you have both R

and RC wires

Note: The wiring for your

application might be

different from the shown

above.

69-2715EF—07 6

Installing your thermostat

Wiring (heat pump system only)

7B Wire thermostat to your heat pump.

a Starting with the C Wire, match the sticky tag on the wire to the terminal

labels.

You must have a C wire.

b Loosen screw, insert wire on inside edge

of terminal, then tighten screw.

c Verify wire is firmly secured by gently

pulling on wire.

d Repeat steps a–c for all other wires.

e Push any excess wire back into the wall

opening after all wires are installed

.

f

Continue to page 8.

Note: If old thermostat has separate wires on AUX and

E, place both wires into the E/AUX terminal.

If old thermostat has wire on AUX with a jumper to E,

place wire on E/AUX terminal. No jumper is required.

Labels don’t match? See alternate

wiring key on pages 7.

MCR33877

G

O

Y

R

HEAT PUMP

AUX/E

G O/B

YRRCK

L

C

Aux

Note: The wiring for your

application might be

different from the wiring

shown above.

Alternate wiring (conventional system)

Use this if your wire labels don’t match the terminal labels.

Note: You must have

a C wire or equivalent.

Y2

R

4M

V

RHY1

H

W1F

RYWG

RC

W2

G W

YRRC

Y2

C

MCR33885

CONVENTIONAL

C

B

C1

X

K

1

2

3

Do not use K terminal. For future use.

If your old thermostat had both R and RH wires, remove metal jumper.

Connect the R wire to the RC terminal, and the RH wire to the R terminal.

Remove metal jumper connecting R and RC only if you must connect both

R and RC.

Alternate wiring key (conventional system)

2

3

1

7 69-2715EF—07

Installing your thermostat

Alternate wiring (heat pump system only)

Use this if your wire labels don’t match the terminal labels.

Note: You must have

a C wire or equivalent.

See page 6.

MCR33886

E AUX

XW FH

B

W1

W2

X2

L

OG

F

C

R

VRM

VY1

B

X

RY

RC

HEAT PUMP

AUX/E

G O/B

YRRCK

L

C

1

2

3

4

7

6

5

4

Alternate wiring key (heat pump system only)

Do not use K terminal. For future use.

If old thermostat has separate wires on AUX and E, place both wires into the E/AUX terminal.

If old thermostat has wire on AUX with a jumper to E, place wire on E/AUX terminal. No

jumper is required.

If your old thermostat had an O wire and not a B wire, attach the O wire to the O/B terminal.

If your old thermostat had separate O and B wires, attach the B wire to the C terminal. If

another wire is attached to the C terminal, check honeywellhome.com for help. Attach the O

wire to the O/B terminal.

If your old thermostat had separate Y1, W1 and W2 wires, check honeywellhome.com for help.

If your old thermostat had both V and VR wires, check honeywellhome.com for help.

Leave metal jumper between R and RC terminals in place.

2

3

1

4

5

6

7

69-2715EF—07 8

Installing your thermostat

8 Insert quick reference card.

Fold quick reference card

along score lines, and slide

it into the slot on the back of

the thermostat.

Back of thermostat

Quick

reference

card

MCR33916

MCR33858

9 Attach thermostat to wallplate.

Align the thermostat to the

wallplate and then snap into

place.

M33860

HOLD

10 Switch heating/cooling system ON.

Important!

10a Verify that the C wire is

connected at the thermostat

and at the heating/cooling

system.

10b Make sure the heating/cooling

system door is firmly secured.

10c Switch power back ON for

your heating/cooling system

at the breaker box or its power

switch.

M31544

or

Circuit breaker

box

Heating/

cooling

system power

switch

9 69-2715EF—07

Installing your thermostat

11 Set clock to current day and time.

11a Press s or t to set clock.

11b Press Set Day.

11c Press s or t to select the

day of week.

11d Press Done to save.

(Press and hold a st button to

quickly change a setting.)

MCR33908

HOLD

MCR33909

HOLD

12 Determine your heating/cooling system type.

Important! Heating/cooling system type must be set so that your

thermostat operates properly and does not damage your system.

12a If your system type is conventional single stage (natural gas-powered single

stage with a/c), continue to “Connecting to your WiFi network” on page 10.

12b If your system is:

• Conventional multistage heat and cool

• Any type of heat pump

• Hydronic

• Other

You MUST change the system type by setting system function 1. See page

18 to match your thermostat to your system type.

If you are not sure of your

heating/cooling system type

or have other questions, go to

honeywellhome.com/support

MCR33880

Congratulations! Your thermostat is operational.

13 Test your thermostat

13a Press the

System

button to change to

heating or cooling and begin operation.

13b For remote access to your thermostat,

continue to

“Connecting to your WiFi

network” on page 10.

Heating/cooling system not

turning on? Refer to page 20

or FAQ at honeywellhome.com/

support

69-2715EF—07 10

Connecting to your WiFi network

To complete this process, you must have a wireless device connected to your home

wireless network. Any of these device types will work:

• Tablet (recommended)

• Laptop (recommended)

• Smartphone

If you get stuck... at any point in this procedure, restart the thermostat by

removing the thermostat from the wallplate, wait for 10 seconds, and snap it

back onto the wallplate. Go to Step 1 in this procedure.

View the WiFi Enrollment video at honeywellhome.com/wifi-thermostat

1 Connect to your thermostat.

1a Make sure the thermostat displays

Wi-Fi Setup.

1b On the wireless device (laptop, tablet,

smartphone), view the list of available WiFi

networks.

1c Connect to the network called

NewThermostat_123456 (the number will

vary).

Note: If you are asked to specify a home, public,

or office network, select Home Network.

M33852

HOLD

2 Join your home network.

2a Open your web browser to access the

Thermostat WiFi Setup page. The browser

should automatically direct you to the correct

page; if it does not, go to http://192.168.1.1

2b Find the name of your home network on this

page and select it.

Note: Some routers have enhanced features such as

guest networks; use your home network.

2c Complete the instructions for joining your

WiFi network and click on the Connect

button. (Depending on your network setup, you

may see an instruction such as Enter Password

for your home network.)

Note: If you did not correctly connect to the thermostat, you may

see your home router page. If so, return to Step 1.

M31567

11 69-2715EF—07

Connecting to your WiFi network

Note: If your WiFi network does not appear in the list on the Thermostat WiFi Setup

page:

• Try performing a network rescan by pressing the Rescan button. This is helpful in

areas with a lot of networks.

• If you are connecting to a hidden network, then enter the network SSID in the

textbox, select the encryption type from the drop down menu, and click on the

Add button. This manually adds the network to the top of the list. Click on the new

network in the list and enter the password if necessary. Click on Connect to join

the network.

3 Make sure your thermostat is connected.

While the connection is in process, your thermostat

will flash Wait for up to 3 minutes. When the

connection is complete, the display will show Wi-Fi

Setup Connection Success. The WiFi signal strength will

appear in the top-right corner.

After about 60 seconds, the home screen will

appear and Register at Total Connect will flash until

registration is complete.

If you don’t see these messages, see page 10.

To register online for remote access to your

thermostat continue on page 12.

Note: If the thermostat displays Connection Failure or continues to display

Wi-Fi Setup, confirm you correctly entered your home network password

in step 2. If correct, refer to the FAQ at honeywellhome.com/support

M33875

M33876

69-2715EF—07 12

Registering your thermostat online

M31570

To view and set your thermostat remotely,

you must have a Total Connect Comfort

account. Use the following steps.

1 Open the Total Connect Comfort web

site.

Go to mytotalconnectcomfort.com

View the Thermostat Registration

video at

honeywellhome.com/wifi-thermostat

2 Login or create an account.

If you have an account,

click Login

– or –

click Create An Account

.

2a Follow the instructions on the screen.

2b Check your email for an activation

message from My Total Connect

Comfort. This may take several minutes.

Note: If you do not receive a response, check

your junk mailbox or use an alternate e-mail

address.

2c Follow activation instructions in the

email.

2d Log in.

M31571

3 Register your thermostat.

After you are logged in to your Total Connect Comfort account,

register your thermostat.

3a Follow the instructions on the

screen. After adding your

thermostat location, you must

enter the thermostat’s unique

identifiers:

• MAC ID

• MAC CRC

Note: These IDs are listed on the

Thermostat ID Card included in the

thermostat package. The IDs are not

case sensitive.

Home logo is used under license from Honeywell International Inc.

69-2723EFS—03 M.S. Rev. 12-18

Printed in U.S.A.

Resideo Inc., 1985 Douglas Drive North,

Golden Valley, MN 55422

69-2723EFS-03

Thermostat ID Card

Use the MAC ID and CRC ID to register

this product at mytotalconnectcomfort.com

Carte d’identification de thermostat

Utilisez l’identiﬁcation MAC et l’identiﬁcation CRC pour enregistrer

ce produit à mytotalconnectcomfort.com

Tarjeta de identificación del termostato

Utilice la identiﬁcación MAC y la identiﬁcación CRC para inscribir este

producto en mytotalconnectcomfort.com

ww

w

.r

es

i

deo

.

com

MAC ID MAC CRC

13 69-2715EF—07

3b When the thermostat is

successfully registered,

the Total Connect Comfort

registration screen will

display a SUCCESS

message.

In the thermostat display,

you will see Setup Complete for

about 90 seconds.

Registering your thermostat online

3c Also notice that your thermostat

displays its signal strength.

Congratulations! You’re done.

You can now control your thermostat

from anywhere through your tablet,

laptop, or smartphone

Total Connect Comfort free app is

available for Apple

®

iPhone

®

, iPad

®

and

iPod touch

®

devices at iTunes

®

or at

Google Play

®

for all Android™ devices.

°

72

GET IT ON

Search for local rebates

Your thermostat may now be eligible for local rebates. Search for

offers in your area at HoneywellHome.com/Rebates

69-2715EF—07 14

1 Press Set Clock/Day/Schedule, then press s or

t to set clock.

2 Press Set Day, then press s or t to select

the day of week.

3 Press Done to save.

Note: If the Set Clock/Day/Schedule option is not

displayed, press Done.

Note: If the display flashes Set Clock, the

thermostat will follow your settings for the

Monday “Wake” time period until you reset the

time and day.

Setting the time and day

MCR33855

HOLD

Press Fan to select On or Auto (toggle to

re-select).

Auto

: Fan runs only when the heating or

cooling system is on. Auto is the most

commonly used setting.

On: Fan is always on.

Note: Options may vary depending on your

heating/cooling equipment.

Setting the fan

MCR33895

Selecting system mode

Note: Depending on how your

thermostat was installed,

you may not see all system

settings.

Press System to select:

Heat: Controls only the heating system.

Cool: Controls only the cooling system.

Off: Heating/cooling systems are off.

Auto: Selects heating or cooling depending

on the indoor temperature.

Em Heat (heat pumps with aux. heat):

Controls auxiliary/emergency heat.

Compressor is off.

MCR33880

15 69-2715EF—07

Adjusting program schedules

1 Press Set Clock/Day/Schedule, then Set Schedule.

2 Press s or t to set your Monday (Mon) Wake

time, then press Next.

3 Press s or t to set the temperature for this

period, then press Next.

4 Set time and temperature for the next time

period (Leave). Repeat Steps 2 and 3 for each

time period.

5 Press Next to set time periods for the next day.

Repeat Steps 2 through 4 for each day.

6 Press Done to save and exit.

Note: Make sure the thermostat is set to the system

mode you want to program (Heat or Cool).

MCR33892

Overriding schedules temporarily

Press s or t to immediately adjust the

temperature.

The new temperature will be maintained only

until the next programmed time period begins.

To cancel the temporary setting at any time,

press Cancel. The program schedule will resume.

MCR33896

HOLD

Overriding schedules permanently

1 Press HOLD to permanently adjust

the temperature. This will turn off the

program schedule.

2 Press s or t to adjust the temperature

setting. The temperature you set will

be maintained 24 hours a day until you

manually change it or press Cancel to

resume the program schedule

MCR33897

HOLD

69-2715EF—07 16

Unregistering thermostat

If you remove the thermostat from your

Total Connect Comfort website account

(for example, you’re moving and leaving

the thermostat behind), the thermostat

will display Register at Total Connect until it is

re-registered.

M33876

Disconnecting WiFi

Replacing your router

If you disconnect the thermostat from your WiFi

network:

1 Enter system setup (see page 18).

2 Change setting 39 to 0 (see page 19).

The screen will display Wi-Fi Setup.

Re-connect to a WiFi network by following the steps on page 10.

Turning WiFi off

If you do not plan to control the thermostat remotely, you can remove the WiFi Setup

message from the screen:

1 Enter system setup (see page 18).

2 Change setting 38 to 0 (see page 19). WiFi Setup will be removed from the screen.

If you want to connect to the WiFi network later, change setting 38 back to 1.

M33855

Software updates

Honeywell periodically issues updates to the software

for this thermostat. The updates occur automatically

through your WiFi connection. All your settings are

saved, so you will not need to make any changes after

the update occurs.

While the update is taking place, your thermostat

screen flashes Updating and shows the percentage of the

update that has occurred. When the update is complete,

your home screen will appear as usual.

Note: If you are not connected to WiFi, you will not get

automatic updates.

M34001

Percentage of

update complete

17 69-2715EF—07

M33881

Smart Response Technology

This feature allows the thermostat to “learn”

how long the heating/cooling system takes

to reach programmed temperature settings,

so the temperature is reached at the time

you set.

For example: Set the Wake time to 6:00 am,

and the temperature to 70°. The heat will

come on before 6:00 am, so the temperature

is 70° by 6:00 am.

Note: System setting function 13 controls

Smart Response Technology. See “Smart

Response Technology” on page 19.

The message Recovery

is displayed when the

system is activated

before a scheduled time

period.

Compressor protection

This feature forces the compressor to wait

a few minutes before restarting, to prevent

equipment damage.

The message Cool On (or Heat On for

a heat pump) will flash during the

wait time.

M33882

Auto changeover

This feature is used in climates where both air

conditioning and heating are used on the same

day.

When the system is set to Auto,

the thermostat automatically

selects heating or cooling

depending on the indoor temperature.

Heat and cool settings must be at least 3 degrees

apart. The thermostat will automatically adjust

settings to maintain this 3-degree separation.

Note: System setting function 12 controls Auto

changeover. See “Manual/Auto Changeover” on

page 19.

MCR33893

69-2715EF—07 18

Setting functions and options

You can change options for a number of system functions. Available functions depend

on the type of system you have. The functions, along with available options are

described on pages 1819.

This thermostat is pre-set for a single-stage heating/cooling system.

Setting function 1 for a heat pump will adjust the default settings.

1 Press Fan and s simultaneously and hold

for approximately 3 seconds. The screen

will change to display two numbers and the

button designations will be Done, Back, blank,

Next.

2 Press Next until you see the function number—

the larger number on the left—you want to set.

3 Change options for any function by pressing

s or t until the correct option (smaller

number on right) is displayed.

4 Repeat Steps 2 and 3 until you have set all

functions that you wish to change.

5 When you have made all changes, press Done

to save and exit.

HOLD

MCR33883

MCR33884

HOLD

System setup

Function Settings & Options

1

Select System

Type

If you are not sure

of your heating/

cooling system

type or have other

questions, go to

honeywellhome.

com

0 Heat/cool: Gas, oil or electric heating with central air conditioning.

1 Heat pump: Heat pump without backup or auxiliary heat.

2 Heat only: Gas, oil or hot water heat without central air conditioning.

3 Heat only with fan: Gas, oil or electric heat without central air

conditioning.

4 Cool only: Central air conditioning only.

5 Heat pump: Heat pump with backup or auxiliary heating.

6 Heat/Cool Multiple stages: 2 heat stages (wires on W and W2), 2

cooling stages (wires on Y and Y2).

7 Heat/Cool Multiple stages: 2 heat stages (wires on W and W2), 1

cooling stage (wire on Y).

8 Heat/Cool Multiple stages: 1 heat stage (wires on W), 2 cooling

stages (wire on Y and Y2).

2

Heat Pump

Changeover Valve

(for heat pumps

only)

0 Cooling changeover valve: Use this setting if you connected a wire

labeled “O” to the O/B terminal.

1 Heating changeover valve: Use this setting if you connected a wire

labeled “B” to the O/B terminal.

3

Heating Fan

Control

0 Gas or oil heat: Use this setting if you have a gas or oil heating system

(system controls fan operation).

1 Electric heat: Use this setting if you have an electric heating system

(thermostat controls fan operation).

La page charge ...

Honeywell RTH6580WF1001/U1 Manuel utilisateur

Honeywell RTH6580WF1001/U1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents