Craftsman CMXEOCG982 Manuel utilisateur

Owner's Manual

SMART GARAGE DOOR OPENER

For Residential Use Only

MODELS CMXEOCG322, CMXEOCG572,

CMXEOCG772, and CMXEOCG982

READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS BEFORE FIRST USE OF THIS PRODUCT.

FASTEN THE MANUAL NEAR THE GARAGE DOOR AFTER INSTALLATION.

PERIODIC CHECKS OF THE OPENER ARE REQUIRED TO ENSURE SAFE OPERATION.

DO NOT INSTALL ON A ONE-PIECE DOOR IF USING DEVICES OR FEATURES PROVIDING UNATTENDED CLOSE.

UNATTENDED DEVICES AND FEATURES ARE TO BE USED ONLY WITH SECTIONAL DOORS. SEE PAGE 3.

WRITE DOWN THE CRAFTSMAN

®

SERIAL NUMBER LOCATED ON THE GARAGE DOOR OPENER:

WWW.CRAFTSMAN.COM

INTRODUCTION 3

Safety Symbol Review and Signal Word Review 3

Unattended Operation 3

Preparing Your Garage Door 3

Tools Needed 4

Test the Wi-Fi® Signal Strength in Your Garage 4

Planning 5

Carton Inventory 7

Hardware Inventory 8

ASSEMBLY 9

Assemble the Rail and Install the Trolley 9

Fasten the Rail to the Motor Unit 9

Install the Idler Pulley 10

Install the Belt 11

Tighten the Belt 11

Install the Sprocket Cover 12

INSTALLATION 12

Important Installation Instructions 12

Determine the Header Bracket Location 13

Install the Header Bracket 14

Attach the Rail to the Header Bracket 15

Position the Opener 16

Hang the Opener 17

Install the Lights 18

Attach the Emergency Release Rope and Handle 18

Fasten the Door Bracket 19

Connect Door Arm to Trolley 21

Attach the Warning Labels 22

Install the Door Control 23

Install The Safety Reversal System 24

Electrical Requirements 27

Aligning the Safety Reversing Sensors 27

ADJUSTMENT 28

Introduction 28

Program the Travel 29

Test the Safety Reversal System 30

Test The Safety Reversing Sensors 30

BATTERY BACKUP Model CMXEOCG982 31

Install the Battery 31

Test the Battery 31

Charge the Battery 31

Battery Status LED 31

myQ® SMARTPHONE CONTROL 32

Connect With Your Smartphone 32

OPERATION 33

Important Safety Instructions 33

Features 34

Dual-Function Control Panel Model CMXEOCG572 35

Door Control Model CMXEOCG322 35

Motion Detecting Control Panel Models CMXEOCG772 and CMXEOCG982 36

Remote Control and Wireless Keypad 37

To Erase the Memory 37

To Open the Door Manually 38

The Remote Control Battery 38

Care of Your Opener 38

TROUBLESHOOTING 39

REPAIR PARTS 40

Rail Assembly Parts 40

Installation Parts 40

Motor Unit Assembly Parts 41

ACCESSORIES 43

WARRANTY 43

AUTOMATIC GARAGE DOOR OPENER SAFETY & MAINTENANCE GUIDE 44

2

TABLE OF CONTENTS

INTRODUCTION

SAFETY SYMBOL REVIEW AND SIGNAL WORD REVIEW

This garage door opener has been designed and tested to offer safe service provided

it is installed, operated, maintained and tested in strict accordance with the

instructions and warnings contained in this manual.

Mechanical

Electrical

When you see these Safety Symbols and Signal Words on the following pages, they will

alert you to the possibility of serious injury or death if you do not comply with the

warnings that accompany them. The hazard may come from something mechanical or

from electric shock. Read the warnings carefully.

When you see this Signal Word on the following pages, it will alert you to the

possibility of damage to your garage door and/or the garage door opener if you do not

comply with the cautionary statements that accompany it. Read them carefully.

WARNING: This product can expose you to chemicals including lead, which

are known to the State of California to cause cancer or birth defects or other

reproductive harm. For more information go to www.P65Warnings.ca.gov

UNATTENDED OPERATION

The Timer-to-Close (TTC) feature and myQ

®

are examples of unattended close and are

to be used ONLY with sectional doors. Any device or feature that allows the door to

close without being in the line of sight of the door is considered unattended close.

The Timer-to-Close (TTC) feature and any myQ

®

devices are to be used ONLY with

sectional doors.

PREPARING YOUR GARAGE DOOR

To prevent possible SERIOUSINJURYor DEATH:

• ALWAYS call a trained door systems technician if garage door binds, sticks, or

is out of balance. An unbalanced garage door may NOT reverse when required.

• NEVER try to loosen, move or adjust garage door, door springs, cables,

pulleys, brackets or their hardware, ALLof which are under EXTREME tension.

• Disable ALLlocks and remove ALLropes connected to garage door BEFORE

installation and operating garage door opener to avoid entanglement.

• DO NOT install on a one-piece door if using devices or features providing

unattended close. Unattended devices and features are to be used ONLY with

sectional doors.

To prevent damage to garage door and opener:

• ALWAYS disable locks BEFORE installing and operating the opener.

• ONLY operate garage door opener at 120V, 60Hz to avoid malfunction and

damage.

Before you begin:

1. Disable locks and remove any ropes connected to the garage door.

2. Lift the door halfway up. Release the door. If balanced, it should stay in

place, supported entirely by its springs.

3. Raise and lower the door to check for binding or sticking. If your door binds,

sticks, or is out of balance, call a trained door systems technician.

4. Check the seal on the bottom of the door. Any gap between the floor and the

bottom of the door must not exceed 1/4" (6mm). Otherwise, the safety

reversal system may not work properly.

5. The opener should be installed above the center of the door. If there is a

torsion spring or center bearing plate in the way of the header bracket, it

may be installed within 4feet (1.2 m) to the left or right of the door center.

See page13.

Sectional Door One-Piece Door

3

TOOLS NEEDED

During assembly, installation and adjustment of the opener, instructions will call for

hand tools as illustrated below.

Drill Bits 3/16",

5/16", and 5/32"

Claw Hammer

Carpenter’s Level

(optional)

Pencil

Screwdriver

Drill

Wire Cutters

Adjustable End Wrench

Tape Measure

Pliers

Sockets and Wrench 1/2",

5/8", 7/16", 9/16", and 1/4"

Hack Saw

Stepladder

TEST THE WI-FI

®

SIGNAL STRENGTH IN YOUR GARAGE

Monitor and control your garage door from anywhere using the myQ

®

App. You will

need a router with Wi-Fi and a smartphone or other mobile device. Make sure your

mobile device is connected to your Wi-Fi network. Hold your mobile device in the

place where your garage door opener will be installed and check the Wi-Fi signal

strength.

Wi-Fi signal is weak.

The garage door opener will likely connect to

your Wi-Fi network. If not, try one of the

options below.

No Wi-Fi signal.

Try one of the following:

• Move your router closer to the garage door

opener to minimize interference from walls

and other objects

• Buy a Wi-Fi range extender

Check Signal Strength. If you see:

Wi-Fi signal is strong.

You’re all set!

Install your new garage door opener.

Visit support.chamberlaingroup.com for more details

See myQ

®

App Control page 32 to connect your garage door opener to your Wi-Fi

network. Do NOT connect prior to installation.

Wi-Fi

®

is a registered trademark of Wi-Fi Alliance

4

PLANNING

Identify the type and height of your garage door. Survey your garage area to see if any

of the conditions below apply to your installation. Additional materials may be

required. You may find it helpful to refer back to this page and the accompanying

illustrations as you proceed with the installation of your opener. Depending on your

requirements, there are several installation steps which may call for materials or

hardware not included in the carton.

• Installation Step 1 – Look at the wall or ceiling above the garage door. The

header bracket must be securely fastened to structural supports.

• Installation Step 5 – Do you have a finished ceiling in your garage? If so, a

support bracket and additional fastening hardware may be required.

• Installation Step 12 – Depending upon garage construction, extension

brackets or wood blocks may be needed to install sensors.

• Installation Step 12 – Alternate floor mounting of the safety reversing

sensor will require hardware not provided.

• Do you have an access door in addition to the garage door? If not, an

emergency key release is required.

• Look at the garage door where it meets the floor. Any gap between the floor

and the bottom of the door must not exceed 1/4" (6 mm). Otherwise, the

safety reversal system may not work properly. See Adjustment Step 2. Floor

or door should be repaired.

SECTIONAL DOOR INSTALLATION

• Do you have a steel, aluminum, fiberglass or glass panel door? If so,

horizontal and vertical reinforcement is required (Installation Step 8).

• The opener should be installed above the center of the door. If there is a

torsion spring or center bearing plate in the way of the header bracket, it

may be installed within 4 feet (1.22 m) to the left or right of the door

center. See Installation Steps 1 and 8.

• If your door is more than 7 feet (2.13 m) high, see rail extension kits listed

on Accessories page.

Safety Reversing Sensor

Header Wall

Access Door

Safety

Reversing

Sensor

Gap between ﬂoor

and bottom of door

must not exceed 1/4" (6 mm).

Extension Spring

Horizontal and vertical reinforcement

is needed for lightweight garage doors

(ﬁberglass, steel, aluminum, door with

glass panels, etc.). See page 18 for details.

Support bracket &

fastening hardware

is required.

See page 16.

FINISHED CEILING

Rail

Wall-mounted

Door Control

OR

Torsion Spring

Vertical

Centerline

of Garage

Door

Header

Wall

Garage

Door

Header

Bracket

Straight

Door

Arm

Emergency Release

Rope & Handle

Door

Bracket

Curved

Door Arm

Garage

Door

Spring

Belt

Rail Tab

SECTIONAL DOOR INSTALLATION

CLOSED POSITION

Trolley

Motor unit

5

PLANNING (CONTINUED)

ONE-PIECE DOOR INSTALLATIONS

• Generally, a one-piece door does not require reinforcement. If your door is

lightweight, refer to the information relating to sectional doors in

Installation Step 8.

• Depending on your door’s construction, you may need additional mounting

hardware for the door bracket (Installation Step 8).

Without a properly installed safety reversing sensor, persons (particularly small

children) could be SERIOUSLY INJURED or KILLED by a closing garage door.

• The gap between the bottom of the garage door and the floor MUST NOT

exceed 1/4" (6 mm). Otherwise, the safety reversal system may NOT work

properly.

• The floor or the garage door MUST be repaired to eliminate the gap.

Safety Reversing

Sensor

Access

Door

FINISHED CEILING

Support bracket

& fastening

hardware is required.

See page 16.

Safety Reversing

Sensor

Header Wall

Gap between ﬂoor

and bottom of door must

not exceed 1/4" (6 mm).

Wall-Mounted

Door Control

Rail

Motor Unit

Header

Wall

Header

Bracket

Trolley

Straight

Door

Arm

Emergency

Release

Rope & Handle

Door Bracket

Curved

Door

Arm

Garage

Door

Rail Tab

Belt

Rail

CLOSED POSITION

Access

Door

Safety

Reversing Sensor

Safety

Reversing Sensor

Gap between ﬂoor

and bottom of door

must not exceed

1/4" (6 mm).

Garage

Door

Header

Wall

Header

Bracket

Door

Bracket

Straight

Door

Arm

Curved

Door Arm

Trolley

Emergency

Release

Rope &

Handle

Rail

Belt

Rail Tab

CLOSED POSITION

ONE-PIECE DOOR WITHOUT TRACK

ONE-PIECE DOOR WITH TRACK

6

CARTON INVENTORY

Your garage door opener is packaged in one carton which contains the motor unit and

all parts illustrated below. Accessories will depend on the model purchased. If

anything is missing, carefully check the packing material.

Hardware for assembly and installation is shown on the next page. Save the carton

and packing material until installation and adjustment is complete.

Straight Door Arm Section

(packaged inside the front rail)

Curved Door

Arm Section

Safety Labels

and Literature

2-Conductor Bell Wire

White and White/Red

Idler Pulley

(In Hardware Bag)

Motor Unit with 2 Light Lenses

Hanging Brackets

(packaged inside the front rail)

(2) Safety Reversing Sensors

(1 Sending Sensor and 1 Receiving Sensor)

with 2-Conductor White and White/Black

Bell Wire attached

Door Bracket

3-Button Remote Control

Trolley

Safety Reversing

Sensor Bracket (2)

Rail

Center/Back

Sections

“U” Bracket

Header Bracket

Hardware Bag

Wireless Keypad

Belt

Rail

Front (header)

Section

Motion-Detecting

Control Panel

Battery

For Model CMXEOCG982

For Model CMXEOCG572

For Model CMXEOCG322

LED Bulb (2)

For Model CMXEOCG982

For Models CMXEOCG772

and CMXEOCG982

For Models CMXEOCG572,

CMXEOCG772, and

CMXEOCG982

For Models CMXEOCG572,

CMXEOCG772, and

CMXEOCG982

For Models CMXEOCG572,

CMXEOCG772, and

CMXEOCG982

For Model CMXEOCG322

Sprocket cover

with screws (3)

Sprocket cover

with screws (2)

Dual-Function Control Panel

Motor Unit with 1 Light Lens

Standard Doorbell

7

HARDWARE INVENTORY

Separate all hardware and group as shown below for the assembly and installation procedures.

Idler Bolt

Nut 3/8"

Lock Washer 3/8"

Lock Nut

1/4"-20

Wing Nut

1/4"-20 (2)

Carriage Bolt

1/4"-20x1/2" (2)

Handle

Nut 5/16"-18 (4)

Ring

Fastener (3)

Insulated Staples

(Not shown)

Drywall Anchors (2)

Clevis Pin

5/16"x1"

Rope

Lock Washer 5/16" (4)

Lag Screw

5/16"-9x1-5/8" (4)

Hex Bolt

5/16"-18x7/8" (4)

Clevis Pin

5/16"x1-1/4"

Screw 6-32x1" (2)

Clevis Pin

5/16"x1-1/2"

Bolt 1/4"-20x1-3/4"

Self-Threading Screw

1/4"-14x5/8" (2)

Screw

6ABx1" (2)

Master Link

Threaded Shaft with

Spring Trolley Nut

ASSEMBLY HARDWARE

INSTALLATION HARDWARE

8

ASSEMBLY STEP 1

ASSEMBLE THE RAIL AND INSTALL THE TROLLEY

To prevent INJURY from pinching, keep hands and fingers away from the joints

while assembling the rail.

To avoid installation difficulties, do not run the garage door opener until instructed

to do so.

The front rail has a cut out “window” at the door end. The front rail has a rail tab.

This tab MUST be on the top of the rail when assembled.

1. Remove the straight door arm and hanging bracket packaged inside the front

rail and set aside for Installation Step 5 and 9. NOTE: To prevent INJURY

while unpacking the rail carefully remove the straight door arm stored within

the rail section.

2. Align the rail sections on a flat surface as shown and slide the tapered ends

into the larger ones. Tabs along the side will lock into place.

3. Place the motor unit on packing material to protect the cover, and rest the

back end of the rail on top. For convenience, put a support under the front

end of the rail.

4. As a temporary stop, insert a screwdriver into the hole 10" (25 cm) from the

front end of the rail, as shown.

5. Check to be sure there are 4 plastic wear pads inside the inner trolley. If

they became loose during shipping, check all packing material. Snap them

back into position as shown.

6. Slide the trolley assembly along the rail from the back end to the

screwdriver.

7. Slide the rail onto the “U” bracket, until it reaches all the stops on the top

and sides of the “U” bracket.

To garage

door opener

(TO MOTOR UNIT)

“U” Bracket

SLIDE TO STOPS

ON TOP AND

SIDES OF

“U” BRACKET

Outer Trolley

Inner Trolley

Wear Pads

Front Rail

Section

(TO DOOR)

Rail

Tab

Trolley

Window

Cut-Out

Idler

Pulley

Hole

ASSEMBLY STEP 2

FASTEN THE RAIL TO THE MOTOR UNIT

To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners

mounted in the top of the opener.

1. Insert a 1/4"-20 x 1-3/4" bolt into the cover protection bolt hole on the back

end of the rail as shown. Tighten securely with a 1/4"-20 lock nut. DO NOT

overtighten.

2. Remove the bolts from the top of the motor unit.

3. Use the carton to support the front end of the rail.

4. Place the “U” bracket, flat side down onto the motor unit and align the

bracket holes with the bolt holes.

5. Fasten the “U” bracket with the previously removed bolts; DO NOT use any

power tools. The use of power tools may permanently damage the garage

door opener.

Lock Nut

1/4"-20

HARDWARE SHOWN ACTUAL SIZE

Bolts

(Mounted in

the garage

door opener)

Bolt 1/4"-20x1-3/4"

“U” Bracket

Cover Protection

Bolt Hole

Bolt

Lock Nut

(Locking feature

must be placed

against the rail)

Bolts (Mounted in the garage door opener)

9

ASSEMBLY STEP 3

INSTALL THE IDLER PULLEY

1. Lay the belt beside the rail, as shown. Grasp the end with the hooked

trolley connector and pass approximately 12" (30 cm) of belt through the

window. Keep the ribbed side toward the rail, and allow it to hang until

Assembly Step 4.

2. Remove the tape from the idler pulley. The inside center should be pre-

greased. If dry, regrease to ensure proper operation.

3. Place the idler pulley into the window as shown.

4. Insert the idler bolt from the top through the rail and pulley. Tighten with a

3/8" lock washer and nut underneath the rail until the lock washer is

compressed.

5. Rotate the pulley to be sure it spins freely.

6. Locate the rail tab. The rail tab is between the idler bolt and the trolley in

the front rail section. Use a flathead screwdriver and lift the rail tab until

the tab is vertical (90º).

Idler Bolt

Rail Tab

CORRECT

INCORRECT

Screwdriver

Grease inside pulley

Pulley

Trolley Connector

Lock Washer 3/8"

Nut 3/8"

Trolley

Nut 3/8"

Idler Bolt

HARDWARE SHOWN ACTUAL SIZE

Lock Washer 3/8"

10

ASSEMBLY STEP 4

INSTALL THE BELT

1. Pull the belt around the idler pulley and toward the trolley. The ribbed side

must contact the pulley.

2. Hook the trolley connector into the retaining slot on the trolley as shown

(Figure1).

3. With the trolley against the screwdriver, dispense the remainder of the belt

along the rail lengthtoward the motor unit and around the sprocket

(Figure2). The sprocket teeth must engage the belt.

4. Check to make sure the belt is not twisted. Connect the trolley threaded

shaft with the master link(Figure3).

• Push pins of master link bar through holes in end of belt and trolley

threaded shaft.

• Push master link cap over pins and past pin notches.

• Slide clip-on spring over cap and onto pin notches until both pins are

securely locked in place.

5. Remove the spring trolley nut from the threaded shaft.

6. Insert the trolley threaded shaft through the hole in the trolley.

Master Link

Figure 3

Threaded Shaft with Spring Trolley Nut

Threaded Shaft

Master Link

Sprocket

Figure 2

Figure 1

Trolley

Connector

Retaining

Slot

ASSEMBLY STEP 5

TIGHTEN THE BELT

1. By hand, thread the spring trolley nut on the threaded shaft until it is finger

tight against the trolley. Do not use any tools. Remove the screwdriver.

2. Insert a flathead screwdriver tip into one of the nut ring slots and brace it

firmly against the trolley.

3. Tighten the spring trolley nut with an adjustable wrench or a 7/16" open end

wrench about a quarter turn until the spring releases and snaps the nut ring

against the trolley. This sets the spring to optimum belt tension.

Nut Ring

BEFORE

1"

(2.5

cm)

Nut Ring

AFTER

1-1/4"

(3.18 cm)

Spring

Trolley Nut

Nut Ring Slot

Spring Trolley

11

ASSEMBLY STEP 6

INSTALL THE SPROCKET COVER

To avoid possible SERIOUS INJURY to finger from moving garage door opener:

• ALWAYS keep hand clear of sprocket while operating opener.

• Securely attach sprocket cover BEFORE operating.

1. Position the sprocket cover over the sprocket as shown and fasten to

the mounting plate with #8x3/8" hex screws provided.

Hex Screw #8x3/8"

(Packed with the

sprocket cover)

HARDWARE SHOWN ACTUAL SIZE

Hex Screws

Sprocket Cover

Hex Screws

Sprocket Cover

OR

You have now finished assembling your garage door opener. Please read the following

warnings before proceeding to the installation section.

INSTALLATION

IMPORTANT INSTALLATION INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS.

2. Install garage door opener ONLY on properly balanced and lubricated garage

door. An improperly balanced door may NOT reverse when required and could

result in SEVERE INJURY or DEATH.

3. ALL repairs to cables, spring assemblies and other hardware MUST be made by

a trained door systems technician BEFORE installing opener.

4. Disable ALL locks and remove ALL ropes connected to garage door BEFORE

installing opener to avoid entanglement.

5. Where possible, install the door opener 7 feet (2.13 m) or more above the floor.

6. Mount the emergency release within reach, but at least 6 feet (1.83 m) above

the floor and avoiding contact with vehicles to avoid accidental release.

7. NEVER connect garage door opener to power source until instructed to do so.

8. NEVER wear watches, rings or loose clothing while installing or servicing

opener. They could be caught in garage door or opener mechanisms.

9. Install wall-mounted garage door control:

• within sight of the garage door.

• out of reach of small children at a minimum height of 5feet (1.5m)

above floors, landings, steps or any other adjacent walking surface.

• away from ALL moving parts of the door.

10. Place entrapment warning label on wall next to garage door control in a

prominent location.

11. Place emergency release/safety reverse test label in plain view on inside of

garage door.

12. Upon completion of installation, test safety reversal system. Door MUST reverse

on contact with a 1-1/2" (3.8cm) high object (or a 2x4 laid flat) on the floor.

13. DO NOT install on a one-piece door if using devices or features providing

unattended close. Unattended devices and features are to be used ONLY with

sectional doors.

12

INSTALLATION STEP 1

DETERMINE THE HEADER BRACKET LOCATION

To prevent possible SERIOUS INJURY or DEATH:

• Header bracket MUST be RIGIDLY fastened to structural support on header

wall or ceiling, otherwise garage door might NOT reverse when required. DO

NOT install header bracket over drywall.

• Concrete anchors MUST be used if mounting header bracket or 2x4 into

masonry.

• NEVER try to loosen, move or adjust garage door, springs, cables, pulleys,

brackets, or their hardware, ALL of which are under EXTREME tension.

• ALWAYS call a trained door systems technician if garage door binds, sticks,

or is out of balance. An unbalanced garage door might NOT reverse when

required.

Installation procedures vary according to garage door types. Follow the instructions

which apply to your door.

1. Close the door and mark the inside vertical centerline of the garage door.

2. Extend the line onto the header wall above the door. You can fasten the

header bracket within 4 feet (1.22 m) of the left or right of the door center

only if a torsion spring or center bearing plate is in the way; or you can

attach it to the ceiling (see page 14) when clearance is minimal. (It may be

mounted on the wall upside down if necessary, to gain approximately 1/2"

(1 cm). If you need to install the header bracket on a 2x4 (on wall or ceiling),

use lag screws (not provided) to securely fasten the 2x4 to structural

supports as shown here and on page 14.

3. Open your door to the highest point of travel as shown. Draw an intersecting

horizontal line on the header wall above the high point:

• 2" (5 cm) above the high point for sectional door and one-piece door with

track.

• 8" (20 cm) above the high point for one-piece door without track.

This height will provide travel clearance for the top edge of the door.

NOTE: If the total number of inches exceeds the height available in your garage, use

the maximum height possible, or refer to page14 for ceiling installation.

Header Wall

Vertical Centerline

of Garage Door

Level

(optional)

2x4

Structural

Supports

Unﬁnished

Ceiling

OPTIONAL

CEILING

MOUNT

FOR

HEADER

BRACKET

Door

Jamb

Hardware

Header Wall

Highest Point

of Travel

Door

2" (5 cm)

Door

Track

Header Wall

Highest Point

of Travel

2" (5 cm)

8" (20 cm)

Highest

Point

of Travel

Door

Pivot

8" (20 cm)

Highest

Point

of Travel

Header Wall

Track

One-piece door with horizontal track

One-piece door without track:

jamb hardware

One-piece door without track:

pivot hardware

Sectional door with curved track

13

INSTALLATION STEP 2

INSTALL THE HEADER BRACKET

You can attach the header bracket either to the wall above the garage door, or to the

ceiling. Follow the instructions which will work best for your particular requirements.

Do not install the header bracket over drywall. If installing into masonry, use

concrete anchors (not provided).

WALL HEADER BRACKET INSTALLATION

1. Center the bracket on the vertical centerline with the bottom edge of the

bracket on the horizontal line as shown (with the arrow pointing toward the

ceiling).

2. Mark the vertical set of bracket holes. Drill 3/16" pilot holes and fasten the

bracket securely to a structural support with the hardware provided.

Lag Screws

5/16"-9x1-5/8"

Highest Point of

Garage Door Travel

Vertical

Centerline

of Garage Door

Door Spring

2x4

Structural

Support

Vertical

Centerline

of Garage Door

Header

Bracket

Horizontal

Line

UP

Wall Mount

Optional

Mounting Holes

Figure 1

Header Wall

Garage Door

CEILING HEADER BRACKET INSTALLATION

1. Extend the vertical centerline onto the ceiling as shown.

2. Center the bracket on the vertical mark, no more than 6" (15cm) from the

wall. Make sure the arrow is pointing away from the wall. The bracket can

be mounted flush against the ceiling when clearance is minimal.

3. Mark the side holes. Drill 3/16" pilot holes and fasten bracket securely to a

structural support with the hardware provided.

Lag Screws

5/16"-9x1-5/8"

Door

Spring

6" (15 cm) Maximum

Header

Bracket

Vertical

Centerline

of Garage Door

Garage Door

Vertical Centerline

of Garage Door

UP

Ceiling Mounting Holes

Figure 2

Header Wall

Finished Ceiling

Lag Screw

5/16"-9x1-5/8"

HARDWARE SHOWN ACTUAL SIZE

14

INSTALLATION STEP 3

ATTACH THE RAIL TO THE HEADER BRACKET

1. Position the opener on the garage floor below the header bracket. Use

packing material as a protective base.

NOTE: If the door spring is in the way, you will need help. Have someone

hold the opener securely on a temporary support to allow the rail to clear

the spring.

2. Position the rail bracket against the header bracket.

3. Align the bracket holes and join with a clevis pin as shown.

4. Insert a ring fastener to secure.

Clevis Pin

Ring Fastener

HARDWARE SHOWN ACTUAL SIZE

Clevis Pin 5/16"x1-1/2" Ring Fastener

15

INSTALLATION STEP 4

POSITION THE OPENER

Follow instructions which apply to your door type as illustrated.

SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK

A 2x4 laid flat is convenient for setting an ideal door-to-rail distance.

1. Raise the opener onto a stepladder. You will need help at this point if the

ladder is not tall enough.

2. Open the door all the way and place a 2x4 laid flat on the top section

beneath the rail (Figure 1).

3. If the top section or panel hits the trolley when you raise the door, pull down

on the trolley release arm to disconnect inner and outer sections. Slide the

outer trolley toward the motor unit. The trolley can remain disconnected until

Installation Step 12 is completed.

ENGAGED

RELEASED

Trolley

Release Arm

ONE-PIECE DOOR WITHOUT TRACK

A 2x4 on its side is convenient for setting an ideal door-to-rail distance.

1. Raise the opener onto a stepladder. You will need help at this point if the

ladder is not tall enough.

2. Open the door all the way and place a 2x4 on its side on the top section of

the door beneath the rail (Figure 2).

3. The top of the door should be level with the top of the motor unit. Do not

position the opener more than 4" (10 cm) above this point.

To prevent damage to garage door, rest garage door opener rail on 2x4 placed on

top section of door.

2x4 is used to

determine the correct

mounting height

from ceiling.

Door

Header Bracket

Top of Door

2x4 is used to

determine the correct

mounting height

from ceiling.

Rail

Figure 1

Figure 2

16

INSTALLATION STEP 5

HANG THE OPENER

To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it

SECURELY to structural supports of the garage. Concrete anchors MUST be used

if installing ANY brackets into masonry.

Three representative installations are shown. Yours may be different. Hanging

brackets should be angled (Figure 1) to provide rigid support. On finished ceilings

(Figures 2 and 3), attach a sturdy metal bracket to structural supports before

installing the opener. This bracket and fastening hardware are not provided.

1. Measure the distance from each side of the motor unit to the structural

support.

2. Cut both pieces of the hanging bracket to required lengths.

3. Drill 3/16" pilot holes in the structural supports.

4. Attach one end of each bracket to a support with 5/16"-9x1-5/8" lag screws.

5. Fasten the opener to the hanging brackets with 5/16"-18x7/8" hex bolts,

lock washers and nuts.

6. Check to make sure the rail is centered over the door (or in line with the

header bracket if the bracket is not centered above the door).

7. Remove the 2x4. Operate the door manually. If the door hits the rail, raise

the header bracket.

NOTE: DO NOT connect power to opener at this time.

Measure

Distance

Lag Screws

5/16"-9x1-5/8"

Structural

Supports

Hex Bolt 5/16"-18x7/8"

Lock Washer 5/16"

Nut 5/16"-18

Bracket

(Not Provided)

Lag Screws

5/16"-9x1-5/8"

(Not Provided)

Bolt 5/16"-18x7/8"

Lock Washer 5/16"

Nut 5/16"-18

Hidden

Support

Hex Bolt 5/16"-18x7/8"

Lock Washer 5/16"

Nut 5/16"-18

Hex Bolt 5/16"-18x7/8"

Lock Washer 5/16"

Nut 5/16"-18

Lag Screws

5/16"-9x1-5/8"

(Not Provided)

Bolt 5/16"-18x7/8"

Lock Washer 5/16"

Nut 5/16"-18

Figure 1

Figure 2

Figure 3

FINISHED CEILING

Lag Screw 5/16"-9x1-5/8"

Hex Bolt

5/16"-18x7/8"

Nut 5/16"-18

Lock Washer 5/16"

HARDWARE SHOWN ACTUAL SIZE

17

INSTALLATION STEP 6

INSTALL THE LIGHTS

To prevent possible OVERHEATING of the end panel or light socket:

• Use ONLY A19 light bulbs.

• DO NOT use incandescent bulbs larger than 100W.

• DO NOT use compact fluorescent light bulbs larger than 26W (100W

equivalent).

• DO NOT use halogen bulbs.

• DO NOT use short neck or specialty light bulbs.

LED bulbs may cause remote control radio interference. Visit craftsman.com for

a list of recommended LED bulbs.

1. Pull light lens down.

2. Insert light bulb.

3. Close light lens.

or

OR

INSTALLATION STEP 7

ATTACH THE EMERGENCY RELEASE ROPE AND HANDLE

To prevent possible SERIOUS INJURY or DEATH from a falling garage door:

• If possible, use emergency release handle to disengage trolley ONLY when

garage door is CLOSED. Weak or broken springs or unbalanced door could

result in an open door falling rapidly and/or unexpectedly.

• NEVER use emergency release handle unless garage doorway is clear of

persons and obstructions.

• NEVER use handle to pull door open or closed. If rope knot becomes untied,

you could fall.

1. Insert one end of the emergency release rope through the handle. Make sure

that “NOTICE” is right side up. Secure with an overhand knot at least 1" (2.5

cm) from the end of the rope to prevent slipping.

2. Insert the other end of the emergency release rope through the hole in the

trolley release arm. Mount the emergency release within reach, but at least 6

feet (1.83m) above floor, avoiding contact with vehicles to prevent

accidental release and secure with an overhand knot.

NOTE: If it is necessary to cut the emergency release rope, seal the cut end with a

match or lighter to prevent unraveling. Ensure the emergency release rope and handle

are above the top of all vehicles to avoid entanglement.

Trolley

Release Arm

Emergency

Release Handle

Overhand

Knot

Trolley

18

INSTALLATION STEP 8

FASTEN THE DOOR BRACKET

Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE

reinforcement BEFORE installation of door bracket. Contact the garage door

manufacturer or installing dealer for opener reinforcement instructions or

reinforcement kit.

Follow instructions which apply to your door type as illustrated below or on the

following page.

A horizontal reinforcement brace should be long enough to be secured to two or

three vertical supports. A vertical reinforcement brace should cover the height of

the top panel.

Figure 1 shows one piece of angle iron as the horizontal brace. For the vertical

brace, 2 pieces of angle iron are used to create a U-shaped support. The best

solution is to check with your garage door manufacturer for an opener installation

door reinforcement kit.

NOTE: Many door reinforcement kits provide for direct attachment of the clevis pin

and door arm. In this case you will not need the door bracket; proceed to Step 9.

SECTIONAL DOORS

1. Center the door bracket on the previously marked vertical centerline used

for the header bracket installation. Note correct UP placement, as stamped

inside the bracket.

2. Position the top edge of the bracket 2"-4" (5-10cm) below the top edge of

the door, OR directly below any structural support across the top of the

door.

3. Mark, drill holes and install as follows, depending on your door’s

construction.

Metal or light weight doors using a vertical angle iron brace between the door panel

support and the door bracket:

• Drill 3/16" fastening holes. Secure the door bracket using the two 1/4"-

14x5/8" self-threading screws. (Figure2A)

• Alternately, use two 5/16"-18x2" bolts, lock washers and nuts (not

provided). (Figure2B)

Metal, insulated or light weight factory reinforced doors:

• Drill 3/16" fastening holes. Secure the door bracket using the self-threading

screws. (Figure3)

Wood doors:

• Use top and bottom or side to side door bracket holes. Drill 5/16" holes

through the door and secure bracket with 5/16"-18x2" carriage bolts, lock

washers and nuts (not provided). (Figure4)

NOTE: The 1/4"-14x5/8" self-threading screws are not intended for use on wood

doors.

Figure 1

Door Bracket

Vertical Centerline

of Garage Door

Vertical Reinforcement

Self-Threading

Screw 1/4"-14x5/8"

UP

Figure 2A

Figure 2B

Bolt

(Not

Door

Bracket

Vertical Reinforcement

5/16"-18x2"

(Not

Provided)

Nut

5/16"-18

Lock Washer 5/16"

UP

Vertical

Centerline

of Garage Door

UP

Self-Threading Screw

1/4"-14x5/8"

Vertical

Centerline

of Garage Door

UP

Inside Edge

of Door or

Reinforcement Board

Bolt 5/16"-18x2"

(Not Provided)

Vertical

Centerline

of Garage

Door

Figure 3

Figure 4

Vertical

Centerline

of Garage

Door

Bracket

Location

Header

Bracket

HORIZONTAL AND VERTICAL

REINFORCEMENT IS NEEDED FOR

LIGHTWEIGHT GARAGE DOORS

(FIBERGLASS, ALUMINUM, STEEL,

DOORS WITH GLASS PANEL, ETC.).

(NOT PROVIDED)

Self-Threading

Screw

1/4"-14x5/8"

HARDWARE

SHOWN ACTUAL

SIZE

19

FASTEN THE DOOR BRACKET (CONTINUED)

ONE-PIECE DOORS

Please read and comply with the warnings and reinforcement instructions on the

previous page. They apply to one-piece doors also.

• Center the door bracket on the top of the door, in line with the header

bracket as shown. Mark either the left and right, or the top and bottom

holes.

• Metal Doors: Drill 3/16" pilot holes and fasten the bracket with the 1/4"-

14x5/8" self-threading screws provided.

• Wood Doors: Drill 5/16" holes and use 5/16"x2" carriage bolts, lock

washers and nuts (not provided) or 5/16"x1-1/2" lag screws (not provided)

depending on your installation needs.

NOTE: The door bracket may be installed on the top edge of the door if required for

your installation. (Refer to the dotted line optional placement drawing.)

Header Wall

Vertical

Centerline of

Garage Door

Optional

Placement

of Door

Bracket

Header

Bracket

Door

Bracket

2x4

Support

For a door with no exposed framing,

or for the optional installation, use

lag screws 5/16"x1-1/2" (Not Provided)

to fasten door bracket.

Top of Door

(Inside Garage)

Door

Bracket

Optional

Placement

Top Edge

of Door

Self-Threading

Screw

1/4"-14x5/8"

Door

Bracket

Top of Door

(Inside Garage)

Carriage Bolt

5/16"x2"

(Not Provided)

Optional

Placement

Lock

Washer

5/16"

Nut

5/16"-18

Top Edge

of Door

METAL DOOR

WOOD DOOR

HORIZONTAL AND VERTICAL

REINFORCEMENT IS NEEDED

FOR LIGHTWEIGHT GARAGE

DOORS (FIBERGLASS, ALUMINUM,

STEEL, DOORS WITH GLASS

PANEL, ETC.). (NOT PROVIDED)

Finished Ceiling

Self-Threading Screw

1/4"-14x5/8"

HARDWARE SHOWN

ACTUAL SIZE

20

La page charge ...

Craftsman CMXEOCG982 Manuel utilisateur

Ce manuel convient également à

Craftsman CMXEOCG982 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents