Zanussi ZWG5100 Manuel utilisateur

Marque: Zanussi

Modèle: ZWG5100

Catégorie: Machines à laver

Taper: Manuel utilisateur

User manual 2

Notice d'utilisation 23

Washing Machine

Lave-linge

ZWG 5100

Contents

Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2

Product description _ _ _ _ _ _ _ _ _ _ _ _ _ 4

Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4

Washing programmes _ _ _ _ _ _ _ _ _ _ _ _ 6

Consumption values _ _ _ _ _ _ _ _ _ _ _ _ _ 9

Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ 10

First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11

Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 12

Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ 14

What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 16

Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 19

Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 19

Electrical connection _ _ _ _ _ _ _ _ _ _ _ _ 21

Environment concerns _ _ _ _ _ _ _ _ _ _ _ 22

Subject to change without notice.

Safety instructions

Important! Read carefully & keep for future

reference.

• The safety of Your appliance complies with

the industry standards and with legal require-

ments on the safety of appliances. However,

as manufacturers, we feel it is our duty to

provide the following safety notes.

• It is most important that this instruction book

should be retained with the appliance for fu-

ture reference. Should the appliance be sold

or transferred to another owner, or should

you move house and leave the appliance, al-

ways ensure that the book is supplied with

the appliance in order that the new owner

can get to know the functioning of the appli-

ance and the relevant warnings.

• You MUST read them carefully before instal-

ling or using the appliance.

• Before first starting up, check the appliance

for any damage incurred during transport.

Never connect up a damaged appliance . If

parts are damaged, contact the Service Cen-

tre.

• If the appliance is delivered in the winter

months when there are minus temperatures.

Store it at room temperature for 24 hours be-

fore using for the first time.

General safety

• It is dangerous to alter the specifications or

attempt to modify this product in any way.

• During high temperature wash programmes

the door glass may get hot. Do not touch it!

• Make sure that small pets and children do

not climb into the drum. To avoid this, please

check into the drum before using.

• Any objects such as coins, safety pins, nails,

screws, stones or any other hard, sharp ma-

terial can cause extensive damage and must

not be placed into the machine.

• Only use the advised quantities of fabric

softener and detergent. Damage to the fabric

can ensue if you over-fill. Refer to the manu-

facturer’s recommendations of quantities.

• Wash small items such as socks, laces,

washable belts in a washing bag or pillow

case as it is possible for such items to slip

down between the tub and the inner drum.

• Do not use your washing machine to wash

articles with whalebones, material without

hems or torn material.

• Always unplug the appliance and turn off the

water supply after use, cleaning and mainte-

nance.

• Under no circumstances should you attempt

to repair the machine yourself. Repairs car-

ried out by inexperienced people may cause

injury or serious malfunctioning. Contact your

local Service Centre. Always insist on genu-

ine spare parts.

Installation

• This appliance is heavy. Care should be tak-

en when moving it.

• When unpacking the appliance, check that it

is not damaged. If in doubt, do not use it and

contact the Service Centre.

www.zanussi.com

• All packing and transit bolts must be re-

moved before use. Serious damage can oc-

cur to the product and to property if this is

not adhered to. See relevant section in the

user manual.

• After having installed the appliance, check

that it is not standing on the inlet and drain

hose and the worktop is not pressing the

electrical supply cable against the wall.

• If the machine is situated on a carpeted floor,

please adjust the feet in order to allow air to

circulate freely under the appliance.

• Always be sure, that there is no water leak-

age from hoses and their connections after

the installation.

• If the appliance is installed in a location sub-

ject to frost, please read the “dangers of

freezing” chapter.

• Any plumbing work required to install this ap-

pliance should be carried out by a qualified

plumber or competent person.

• Any electrical work required to install this ap-

pliance should be carried out by a certified

Service Centre.

Use

• This appliance is designed for domestic use.

It must not be used for purposes other than

those for which it was designed.

• Only wash fabrics which are designed to be

machine washed. Follow the instructions on

each garment label.

• Do not overload the appliance. See the

Washing Programme Table.

• Before washing, ensure that all pockets are

empty and buttons and zips are fastened.

Avoid washing frayed or torn articles and

treat stains such as paint, ink, rust, and grass

before washing. Underwired bras must NOT

be machine washed.

• Garments which have been in contact with

volatile petroleum products should not be

machine washed. If volatile cleaning fluids

are used, care should be taken to ensure that

the fluid is removed from the garment before

placing in the machine.

• Never pull the power supply cable to remove

the plug from the socket; always take hold of

the plug itself.

• Never use the appliance if the power supply

cable, the control panel, the working surface

or the base are damaged so that the inside

of the washing machine is accessible.

Child safety

• This appliance is not intended for use by per-

son (including children) with reduced physi-

cal sensory or mental capabilities or lack of

experience and knowledge unless they have

been given supervision or instruction con-

cerning use of the appliance by a person re-

sponsible for their safety.

• Children should be supervised to ensure that

they do not play with the appliance.

• The packaging components (e.g. plastic film,

polystyrene) can be dangerous to children -

danger of suffocation! Keep them out of chil-

dren’s reach

• Keep all detergents in a safe place out of

children’s reach.

• Make sure that children or pets do not climb

into the drum. To prevent children and pets

becoming trapped inside the drum this ma-

chine incorporates a special feature.

Door safety button

To activate this de-

vice, rotate the button

(without pressing it)

inside the door clock-

wise until the groove

is horizontal. If neces-

sary use a coin.

To disable this de-

vice and restore the

possibility of closing

the door, rotate the

button counter-clock-

wise until the groove

is vertical.

www.zanussi.com

Product description

Detergent dispenser drawer

Control panel

Door opening handle

Rating Plate

Drain pump

Adjustable feet

Detergent dispenser drawer

Compartment for detergent used for pre-

wash and soak phase or for stain remover used

during the stain action phase (if available). The

prewash and soak detergent is added at the be-

ginning of the wash programme. The stain re-

mover is added during the stain action phase.

Compartment for powder or liquid detergent

used for main wash. If using liquid detergent

pour it just before starting the programme.

Compartment for liquid additives (fabric soft-

ener, starch).

Follow the product manufacturer’s recommendations on quantities to use and do not exceed the

«MAX» mark in the detergent dispenser drawer. Any fabric softener or starching additives must

be poured into the compartment before starting the wash programme.

Control panel

www.zanussi.com

Below is a picture of the control panel. It shows the programme selector dial as well as the

buttons and the pilot lights. These are presented by relevant numbers on the following pages.

1 2 3 4 5 6 7

Programme selector dial

Temperature selector dial

SPIN reduction button

OPTIONS button

EXTRA RINSE button

START/PAUSE button

Indicator Pilot Light

Table of symbols

= Off/Reset = Rinses

= Cotton = Drain

= + Prewash = Spin

= Economy = Cold wash

= Economy +

Prewash

= Rinse hold

= Synthetics = Options

= Synthetics

+ Prewash

= Easy Iron

= Delicates = Super Quick

= Special

programmes

= Extra Rinse

= Wool = Start Pause

= Handwash = Door

= Jeans = End cycle

= Sport In-

tensive

= Washing

phase

Programme Selector Dial

It allows you to switch the appliance on/off and/

or to select a programme.

Temperature selector dial

This dial allows you to select the temperature

more suitable to the laundry to be washed.

By selecting the position

(Cold) the ma-

chine will wash with cold water.

Spin Reduction

By pressing this button you can change the

spin speed of the selected programme.

Available options:

Rinse hold

By selecting this function the water of the last

rinse is not emptied out to prevent the fabrics

from creasing. Before opening the door it will

be necessary to empty out the water. To empty

out the water, please read the paragraph «At

the end of the programme».

Easy Iron

By selecting this option the laundry is gently

washed and spun to avoid any creasing. In this

way ironing is easier. Furthermore the machine

will perform some additional rinses in some

www.zanussi.com

programmes. On cotton programmes the maxi-

mum spin speed is reduced automatically.

Super Quick

Short cycle for lightly soiled items or for laundry

which needs only freshening up. We recom-

mend you to reduce the fabrics loading.

Extra Rinse

This appliance is designed to save energy. If it

necessary to rinse the laundry using an extra

quantity of water (extra rinse), select this option.

Some additional rinses will be performed. This

option is recommended for people who are al-

lergic to detergents, and in areas where the

water is very soft.

Start Pause

This button allows you to start or to interrupt

the selected programme.

Indicator pilot lights

After having pressed the button 6, the WASH-

ING pilot light (A) illuminates. When the pilot

light A comes on this means that the machine is

operating.

When the programme has finished the END

CYCLE pilot light (B) comes on.

The DOOR pilot light (C) illuminates when the

programme starts and indicates if the door can

be opened:

• light on: the door cannot be opened. The

machine in working or has stopped with wa-

ter left in the tub.

• light off: the door can be opened. The pro-

gramme is finished or the water has been

emptied out.

• light flashing: the door is opening.

Washing programmes

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent

Compartment

COTTON

Normal

90° - Cold

Main wash - Rinses

Maximum spin speed 1000 rpm

Max. load 6 kg - Reduced load 3 kg

White and coloured cotton (normally soiled items).

SPIN

RINSE HOLD

EASY IRON

SUPER QUICK

EXTRA RINSE

www.zanussi.com

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent

Compartment

COTTON

+ Prewash

90° - Cold

Prewash - Main wash - Rinses

Maximum spin speed 1000 rpm

Max. load 6 kg - Reduced load 3 kg

White and coloured cotton (heavy soiled items).

SPIN

RINSE HOLD

EASY IRON

SUPER QUICK

EXTRA RINSE

COTTON

ECO

90° - 40°

Main wash - Rinses

Maximum spin speed 1000 rpm

Max. load 6 kg

White and coloured cotton. This programme can be se-

lected for slightly or normally soiled cotton items. The tem-

perature will decrease and the washing time will be exten-

ded. This allows to obtain a good washing efficiency by

saving energy.

SPIN

RINSE HOLD

EASY IRON

EXTRA RINSE

COTONI

ECO + Prewash

90° - 40°

Prewash - Main wash - Rinses

Maximum spin speed 1000 rpm

Max. load 6 kg

White and coloured cotton. This programme can be se-

lected for normally soiled cotton items. The temperature

will decrease and the washing time will be extended. This

allows to obtain a good washing efficiency by saving ener-

gy.

SPIN

RINSE HOLD

EASY IRON

EXTRA RINSE

SYNTHETICS

Normal

60° -

(Cold)

Main wash - Rinses

Maximum spin speed 700 rpm for

Max. load 3 kg - Reduced load 1.5 kg

Synthetic or mixed fabrics: underwear, coloured gar-

ments, non-shrink shirts, blouses.

SPIN

RINSE HOLD

EASY IRON

SUPER QUICK

EXTRA RINSE

SYNTHETICS

+ Prewash

60° -

(Cold)

Prewash - Main wash - Rinses

Maximum spin speed 700 rpm

Max. load 3 kg - Reduced load 1.5 kg

Synthetic or mixed fabrics: underwear, coloured gar-

ments, non-shrink shirts, blouses.

SPIN

RINSE HOLD

EASY IRON

SUPER QUICK

EXTRA RINSE

www.zanussi.com

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent

Compartment

DELICATES

40° -

(Cold)

Main wash - Rinses

Maximum spin speed 700 rpm

Max. load kg 3 - Reduced load 1.5 kg

Delicate fabrics: acrylics, viscose, polyester.

SPIN

RINSE HOLD

EASY IRON

EXTRA RINSE

WOOL

40° -

(Cold)

Main wash - Rinses

Maximum spin speed 1000 rpm

Max. load 2 kg

Washing programme for machine washable wool as well

as for hand washable woollens and delicate fabrics.

SPIN

RINSE HOLD

HANDWASH

30° -

(Cold)

Main wash - Rinses

Maximum spin speed 1000 rpm

Max. load 2 kg

Special programme for delicate fabrics with «hand wash-

ing» care symbol.

SPIN

RINSE HOLD

JEANS

60° -

(Cold)

Main wash - Rinses

Maximum spin speed at 1000 rpm

Max. load 4 kg

With this programme it is possible to wash items like

pants, shirts or jackets in denim and also jersey realized

with hi-tech materials.

SPIN

RINSE HOLD

EASY IRON

EXTRA RINSE

SPORT INTENSIVE

40° -

(Cold)

Prewash - Main wash - Rinses

Maximum spin speed at 700 rpm

Max. load 2 kg

This programme is suitable for washing heavily soiled sport

items. The machine will add automatically a prewash phase

before the main wash to eliminate mud stains.

SPIN

RINSE HOLD

EXTRA RINSE

RINSES

Rinses

Maximum spin speed 1000 rpm

Max. load 6 kg

With this programme it is possible to rinse and spin cotton

garments which have been washed by hand. The machine

performs 3 rinses, followed by a final long spin. The spin

speed can be reduced.

SPIN

RINSE HOLD

EASY IRON

EXTRA RINSE

www.zanussi.com

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent

Compartment

DRAIN

Draining of water

Max. load 6 kg

For emptying out the water of the last rinse in programmes

with the Rinse Hold option selected.

SPIN

Drain and long spin

Maximum spin speed 1000 rpm

Max. load 6 kg

Separate spin for hand washed garments and after pro-

grammes with the Rinse Hold option selected. You can

choose the spin speed by pressing the relevant button to

adapt it to the fabrics to be spun.

SPIN

= OFF/RESET

For cancelling the programme which is running or to switch the machine on or off .

1) If you select the Super Quick option by pressing button 4, we recommend that you reduce the maximum

load as indicated. Full loading is possible however with somewhat reduced cleaning results.

2) If using liquid detergents, a programme without PREWASH must be selected.

3) Standard programmes for the Energy Label consumption values. According to regulation 1061/2010, the

«Cotton Eco 60 °C» and «Cotton Eco 40 °C» are respectively the «standard 60 °C cotton programme» and

the «standard 40 °C cotton programme». Set this programme to have a good washing results and decrease

the energy consumption. The time of the washing programme is extended. Set this programme to have a

good washing results and decrease the energy consumption. The time of the washing programme is

extended.

4) The extra rinse option will be activated automatically.

Consumption values

The values of this table are indicative. Different causes can change the data: the quantity and

type of laundry, the water and ambient temperature.

Programmes

Load

(kg)

Energy con-

sumption

(kWh)

Water con-

sumption (litre)

Approximate

programme

duration (mi-

nutes)

Remaining

moisture

(%)

Cottons 60 °C 6 1.30 58 125 66

Cottons 40 °C 6 0.7 58 120 66

Synthetics 40 °C 3 0.5 45 95 37

Delicates 40 °C 3 0.55 60 55 37

Wool/Hand wash

30 °C

2 0.25 53 55 37

www.zanussi.com

Programmes

Load

(kg)

Energy con-

sumption

(kWh)

Water con-

sumption (litre)

Approximate

programme

duration (mi-

nutes)

Remaining

moisture

(%)

Standard cotton programmes

Standard 60 °C

cotton

6 0.88 50 171 66

Standard 60 °C

cotton

3 0.68 33 149 66

Standard 40 °C

cotton

3 0.57 34 139 66

1) These values have been measured in the condition of CEI 60456.

2) At the end of spin phase.

Helpful hints and tips

Sorting out the laundry

Follow the wash code symbols on each gar-

ment label and the manufacturer’s washing in-

structions. Sort the laundry as follows: whites,

coloureds, synthetics, delicates, woollens.

Temperatures

95° or 90°

for normally soiled white cottons

and linen (e.g. tea cloths, towels,

tablecloths, sheets...)

60°/50°

for normally soiled, colour fast

garments (e.g. shirts, night dres-

ses, pyjamas....) in linen, cotton or

synthetic fibres and for lightly

soiled white cotton (e.g. under-

wear)

40°-30°- Cold

for delicate items (e.g. net cur-

tains), mixed laundry including

synthetic fibres and woollens

bearing the label «pure new wool,

machine washable, non-shrink»

Before loading the laundry

Never wash whites and coloureds together.

Whites may lose their «whiteness» in the wash.

New coloured items may run in the first wash;

they should therefore be washed separately the

first time.

Make sure that no metal objects are left

in the laundry (e.g. hair clips, safety pins,

pins).

Button up pillowcases, close zip fasteners,

hooks and poppers. Tie any belts or long tapes.

Remove persistent stains before washing.

Rub particularly soiled areas with a special de-

tergent or detergent paste.

Treat curtains with special care. Remove hooks

or tie them up in a bag or net.

Maximum loads

Recommended loads are indicated in the

washing programme charts.

General rules:

• Cotton, linen: drum full but not too tightly

packed;

• Synthetics: drum no more than half full;

• Delicate fabrics and woollens: drum no

more than one third full.

Washing a maximum load makes the most effi-

cient use of water and energy.

For heavily soiled laundry, reduce the load size.

Removing stains

Stubborn stains may not be removed by just

water and detergent. It is therefore advisable to

treat them prior to washing.

Blood: treat fresh stains with cold water. For

dried stains, soak overnight in water with a spe-

cial detergent then rub in the soap and water.

Oil based paint: moisten with benzine stain

remover, lay the garment on a soft cloth and

dab the stain; treat several times.

www.zanussi.com

Dried grease stains: moisten with turpentine,

lay the garment on a soft surface and dab the

stain with the fingertips and a cotton cloth.

Rust: oxalic acid dissolved in hot water or a

rust removing product used cold. Be careful

with rust stains which are not recent since the

cellulose structure will already have been dam-

aged and the fabric tends to hole.

Mould stains: treat with bleach, rinse well

(whites and fast coloureds only).

Grass: soap lightly and treat with bleach

(whites and fast coloureds only).

Ball point pen and glue: moisten with ace-

tone

, lay the garment on a soft cloth and dab

the stain.

Lipstick: moisten with acetone as above, then

treat stains with methylated spirits. Treat any re-

sidual marks with bleach.

Red wine: soak in water and detergent, rinse

and treat with acetic or citric acid, then rinse.

Treat any residual marks with bleach.

Ink: depending on the type of ink, moisten the

fabric first with acetone

, then with acetic acid;

treat any residual marks on white fabrics with

bleach and then rinse thoroughly.

Tar stains: first treat with stain remover, me-

thylated spirits or benzine, then rub with deter-

gent paste.

Detergents and additives

Good washing results also depend on the

choice of detergent and use of the correct

quantities to avoid waste and protect the envi-

ronment.

Although biodegradable, detergents contain

substances which, in large quantities, can up-

set the delicate balance of nature.

The choice of detergent will depend on the

type of fabric (delicates, woollens, cottons,

etc.), the colour, washing temperature and de-

gree of soiling.

All commonly available washing machine deter-

gents may be used in this appliance:

• powder detergents for all types of fabric

• powder detergents for delicate fabrics (60°C

max) and woollens

• liquid detergents, preferably for low tempera-

ture wash programmes (60°C max) for all

types of fabric, or special for woollens only.

The detergent and any additives must be

placed in the appropriate compartments of the

dispenser drawer before starting the wash pro-

gramme.

If using liquid detergents, a programme with-

out prewash must be selected.

Follow the product manufacturer’s recommen-

dations on quantities to use and do not ex-

ceed the «MAX» mark in the detergent

dispenser drawer.

Quantity of detergent to be used

The type and quantity of detergent will depend

on the type of fabric, load size, degree of soiling

and hardness of the water used.

Follow the product manufacturers’ instructions

on quantities to use.

Use less detergent if:

• you are washing a small load

• the laundry is lightly soiled

• large amounts of foam form during washing.

Degrees of water hardness

Water hardness is classified in so-called “de-

grees” of hardness. Information on hardness of

the water in your area can be obtained from the

relevant water supply company, or from your lo-

cal authority. If the water hardness degree is

medium or high we suggest you to add a water

softener following always the manufacturer’s in-

structions. When the degree of hardness is

soft, readjust the quantity of the detergent.

First use

• Ensure that the electrical and water

connections comply with the installation

instructions.

• Remove the polystyrene block and any

material from the drum.

• Pour 2 litres of water into the main wash

compartment

of the detergent draw-

1) do not use acetone on artificial silk

www.zanussi.com

er in order to activate the ECO valve.

Then run a cotton cycle at the highest

temperature without any laundry in the

machine, to remove any manufacturing

residue from the drum and tub. Pour 1/2

a measure of detergent into the main

wash compartment and start the ma-

chine.

Daily use

Load the laundry

Open the door by

carefully pulling the

door handle out-

wards. Place the

laundry in the drum,

one item at a time,

shaking them out as

much as possible.

Close the door.

Make sure that no

laundry stays be-

tween the seal and

the door. There is a

risk of water leakage

or damage to the

laundry.

Measure out the detergent and the fabric

softener

Pull out the dispenser drawer until it stops.

Measure out the amount of detergent re-

quired, pour it into the main wash compart-

ment

or in the appropriate compartment if

the selected programme/option it requires

(see more details in "Detergent dispenser

drawer").

If required, pour fabric softener into the com-

partment marked

(the amount used must

not exceed the «MAX» mark in the drawer).

Close the drawer gently.

Select the required programme by turning

the programme selector dial (1)

Turn the programme selector dial to the re-

quired programme. The washing machine will

automatically select the maximum spin value

provided for the programme you have chosen.

You can change this value by pressing the cor-

responding button. The green pilot light of the

button 6 starts to flash.

The selector dial can be turned either clockwise

or counterclockwise. Turn to position «O» to re-

set programme/Switching the machine off.

At the end of the programme the selector

dial must be turned to position O, to

switch the machine off.

Caution! If you turn the programme

selector dial to another programme when

the machine is working, the red pilot light of

button 6 will blink 3 times to indicate a wrong

selection. The machine will not perform the new

selected programme.

Select the required temperature by

turning the temperature selector dial (2)

Turn clockwise this dial to select the more con-

venient to your laundry washing temperature.

www.zanussi.com

Reduce the spin speed by pressing button

By selecting a programme, the appliance pro-

poses automatically the maximum spin speed

provided for that programme.

Press button 3 repeatedly to change the spin

speed, if you want your laundry to be spun at a

different speed. The relevant light illuminates.

Select the available options by pressing

buttons 3, 4 and 5

Depending on the programme, different func-

tions can be combined. These must be selec-

ted after choosing the desired programme and

before starting the programme.

When these buttons are pressed, the corre-

sponding pilot lights illuminate. When they are

pressed again, the pilot lights go out. If an in-

correct option is selected, the integrated red

pilot light of the button 6 flashes for 3 times.

For the compatibility among the washing

programmes and the options see chapter

«Washing Programmes».

Start the programme by pressing button 6

To start the selected programme, press the

button 6, the corresponding green pilot light

stops blinking. The pilot lightsA and C illumi-

nate to indicate that the appliance starts oper-

ating and the door is locked.

To interrupt a programme which is running,

press the button 6: the corresponding green pi-

lot light starts blinking.

To restart the programme from the point at

which it was interrupted, press the button 6

again. If you have chosen a delayed start, the

machine will begin the countdown.

If an incorrect option is selected, the red pilot

light of the button 6 blinks for 3 times.

Altering an option or a running

programme

It is possible to change some options before

the programme carries them out.

Before you make any change, you must PAUSE

the appliance by pressing the button 6.

Changing a running programme is possible only

by resetting it. Turn the programme selector di-

al to O and then to the new programme posi-

tion. Start the new programme by pressing the

button 6 again. The washing water in the tub

will be not emptied out.

Interrupting a programme

Press the button 6 to interrupt a programme

which is running, the corresponding green pilot

light starts blinking.

Press the button again to restart the pro-

gramme.

Cancelling a programme

Turn the selector dial to

to cancel a pro-

gramme which is running.

You can select now a new programme.

Opening the door

After the programme has started (or during the

delay time) the door is locked, if you need to

open it, set first the machine to PAUSE by

pressing the button 6. After a few minutes the

light C goes out and it is possible to open the

door.

If this light remains lit and the door is locked,

this means that the machine is already heating

or that the water level is too high. In any case,

do not try to force the door!

If you cannot open the door but you need to

open it you have to switch the machine off by

turning the selector dial to

. After a few mi-

nutes the door can be opened (pay attention

to the water level and temperature!).

After closing the door, it is necessary to select

the programme and options again and to press

button 6.

At the end of the programme

The machine stops automatically. The pilot light

of button 6, the pilot lightsA and C go off. The

light B illuminates.

If a programme or an option that ends with wa-

ter left in the tub has been selected, the pilot

light C remains on and the door is locked to in-

dicate that the water must be emptied out be-

fore opening the door.

Follow the below instructions to empty out the

water:

Turn the programme selector dial to

2. Select the draining or spinning programme.

www.zanussi.com

3. Reduce the spin speed if needed, by

pressing the relevant button.

4. Press button 6.

At the end of the programme, the pilot light C

goes off to indicate that the door can be now

opened. Turn the programme selector dial to

to switch the machine off.

Remove the laundry from the drum and carefully

check that the drum is empty. If you do not in-

tend to carry out another wash, close the water

tap. Leave the door open to prevent the forma-

tion of mildew and unpleasant smells.

Care and cleaning

Warning! You must DISCONNECT the

appliance from the electricity supply,

before you can carry out any cleaning or

maintenance work.

Descaling

The water we use normally contains lime. It is a

good idea to periodically use a water softening

powder in the machine. Do this separately from

any laundry washing, and according to the soft-

ening powder manufacturer's instructions. This

will help to prevent the formation of lime depos-

its.

External cleaning

Clean the exterior cabinet of the appliance with

soap and water only, and then dry thoroughly.

Cleaning the dispenser drawer

The washing powder and additive dispenser

drawer should be cleaned regularly.

Remove the drawer

by pressing the catch

downwards and by

pulling it out. Flush it

out under a tap, to re-

move any traces of

accumulated powder.

To aid cleaning, the

top part of the addi-

tive compartment

should be removed.

Cleaning the drawer recess

Having removed the

drawer, use a small

brush to clean the re-

cess, ensuring that all

washing powder resi-

due is removed from

the upper and lower

part of the recess.

Replace the drawer and run the rinse pro-

gramme without any clothes in the drum.

Cleaning the pump

The pump should be inspected regularly and

particularly if:

• The appliance does not empty and/or spin.

• The appliance makes an unusual noise dur-

ing draining due to objects such as safety

pins, coins etc. blocking the pump.

• A problem with water draining is detected

(see chapter “What to do if...” for more de-

tails).

Warning! Before opening the pump door,

switch the appliance off and remove the

mains plug from the socket.

Proceed as follows:

• Unplug the appliance.

• If it is necessary, wait until the water has

cooled down.

www.zanussi.com

Open the pump door.

Place a container

close to the pump .

Unscrew carefully the

drain filter to drain out

the water.

When no more water comes out, remove the

filter. If necessary, use pliers.

Always keep a rag nearby to dry up any water

spillage when removing the filter.

Clean the filter under a tap, to remove any

traces of fluff.

Remove foreign bod-

ies and fluff from the

pump impeller.

Check carefully whether the pump impeller

rotates (it rotates jerkily). If it doesn’t rotate,

please contact the Service.

Replace the filter into

the pump by inserting

it correctly into the

special guides.

Screw firmly the filter.

Close the pump door.

Caution! When the appliance is in use

and depending on the programme

selected there can be hot water in the pump.

Never remove the filter during a wash cycle.

Always wait until the appliance has finished the

cycle, and is empty.

When refitting the filter, ensure it is securely re-

tightened so as to stop leaks and young

children being able to remove it.

Cleaning the water inlet filters

If the appliance doesn't fill, takes long to fill

with water, the starting button blinks red or

the display (if available) shows the relevant

alarm (see chapter "What to do if..." for more

details), check if the water inlet filters are

blocked .

To clean the water inlet filters:

• Turn off the water

tap.

• Unscrew the hose

from the tap.

• Clean the filter in

the hose with a stiff

brush.

• Screw the hose back onto the tap. Make

sure the connection is tight.

www.zanussi.com

• Unscrew the hose

from the machine.

Keep a rag nearby

because some wa-

ter may flow.

• Clean the filter in

the valve with a

stiff brush or with

the piece of cloth.

35°

45°

• Screw the hose back to the machine and

make sure the connection is tight.

• Turn on the water tap.

Frost precautions

If the machine is installed in a place where the

temperature could drop below 0°C, remove the

remaining water from the inlet hose and the

drain pump.

1. disconnect the mains plug from the mains

socket.

2. close the water tap

3. unscrew the water inlet hose from the tap;

4. put the two ends of the inlet hose in a con-

tainer and let the water flow out of the

hose.

5. empty the drain pump as described in the

‘Emergency emptying out’ section.

6. when the drain pump is empty, install the

water inlet hose again.

Warning!

Make sure that the temperature is more than 0

°C before you use the appliance again.

The manufacturer is not responsible for dam-

ages caused by low temperatures.

Emergency emptying out

If the water is not discharged, proceed as fol-

lows to empty out the machine:

1. Pull out the plug from the power socket.

2. Close the water tap.

3. If necessary, wait until the water has

cooled down.

4. Open the pump door.

5. Place a bowl on the floor.

6. Unscrew carefully the filter. When the bowl

is full, screw the filter again.

– The water drain out by gravity into the

bowl.

– Empty the bowl.

– Repeat the procedure until water stops

flowing out.

7. Clean the pump if necessary as previously

described.

8. Screw firmly the filter again and close the

door pump.

Important! Every time you drain the water

through the emergency emptying hose you

must pour 2 litres of water into the main wash

compartment of the detergent drawer and then

run the drain programme. This will activate the

ECO Valve device avoiding that part of the

detergent remains unused at next washing.

What to do if…

Certain problems are due to lack of simple

maintenance or oversights, which can be

solved easily without calling out an engineer.

Before contacting your local Service Centre,

please carry out the checks listed below.

During machine operation it is possible that the

red pilot light of button 6 blinks to indicate that

the machine is not working.

It is possible to recognize the fault machine by

the number of button 6 light flashes. If the num-

ber of flashes is different from the ones indica-

ted below, this is related to a fault that you can

not solve. In this case, contact your local Serv-

ice Centre.

Press simultaneously the buttons 4 and 5 for a

few seconds. The red button 6 light will flash

www.zanussi.com

for a short time as described (the green flash is

not to be considered) :

• 4 flashes = «The washing machine does

not start», follow the corresponding sug-

gestions in «Possible cause/Solutions» box

and restart the programme.

• 1 flash = «The machine does not fill»,

follow the corresponding suggestions in

«Possible cause/Solutions» box and restart

the programme.

• 2 flashes = «The machine does not

empty and/or does not spin», follow the

corresponding suggestions in «Possible

cause/Solutions» box and restart the pro-

gramme.

Once the problem has been eliminated, press

the button 6 to restart the programme. If after

all checks, the problem persists, contact your

local Service Centre.

Problem Possible cause/Solution

The washing machine does

not start:

The door has not been closed (the button 6 red light blinks).

• Close the door firmly.

The plug is not properly inserted in the power socket.

• Insert the plug into the power socket.

There is no power at the socket.

• Please check your domestic electrical installation.

The main fuse has blown.

• Replace the fuse.

The programme selector dial is not correctly positioned and the button 6

has not been pressed.

• Please turn the selector dial and press the button 6 again.

The machine does not fill:

The water tap is closed (the button 6 red light blinks).

• Open the water tap.

The inlet hose is squashed or kinked (the button 6 red light blinks).

• Check the inlet hose connection.

The filter in the inlet hose or the inlet valve filter are blocked (the button 6

red light blinks).

• Clean the water inlet filters. (See "Cleaning the water inlet filters" for

more details).

The door is not properly closed (the button 6 red light blinks).

• Close the door firmly.

The machine does not empty

and/or does not spin:

The drain hose is squashed or kinked (the button 6 red light blinks).

• Check the drain hose connection.

The drain filter is clogged (the button 6 red light blinks).

• Clean the drain filter.

An option or a programme that ends with the water still in the tub or a

that eliminates all the spinning phases has been selected.

• Select the draining or spinning programme.

The laundry is not evenly distributed in the drum.

• Redistribute the laundry.

www.zanussi.com

Problem Possible cause/Solution

There is water on the floor:

Too much detergent or unsuitable detergent (creates too much foam)

has been used.

• Reduce the detergent quantity or use another one.

Check whether there are any leaks from one of the inlet hose fittings. It is

not always easy to see this as the water runs down the hose; check to

see if it is damp.

• Check the water inlet hose connection.

The drain or inlet hose is damaged.

• Replace it with a new one.

The filter of the drain pump has not been properly screwed in after

cleaning action.

• Screw the filter fully in.

Unsatisfactory washing re-

sults:

Too little detergent or unsuitable detergent has been used.

• Increase the detergent quantity or use another one.

Stubborn stains have not been treated prior to washing.

• Use commercial products to treat the stubborn stains.

The correct temperature was not selected.

• Check if you have selected the correct temperature.

Excessive laundry load.

• Reduce the laundry load.

The door will not open:

The programme is still running.

• Wait the end of washing cycle.

The door lock has not been released.

• Wait until the pilot light C goes off.

There is water in the drum.

• Select drain or spin programme to empty out the water.

The machine vibrates is

noisy:

The transit bolts and packing have not been removed.

• Check the correct installation of the appliance.

The support feet have not been adjusted

• Check the correct levelling of the appliance.

The laundry is not evenly distributed in the drum.

• Redistribute the laundry.

Maybe there is very little laundry in the drum.

• Load more laundry.

Spinning starts late or the

machine does not spin:

The electronic unbalance detection device has cut in because the laun-

dry is not evenly distributed in the drum. The laundry is redistributed by

reverse rotation of the drum. This may happen several times before the

unbalance disappears and normal spinning can resume. If, after 10 mi-

nutes, the laundry is still not evenly distributed in the drum, the machine

will not spin. In this case, redistribute the load manually and select the

spin programme.

• Redistribute the laundry.

The load is too small.

• Add more items, redistribute the load manually and then select the

spinning programme.

www.zanussi.com

Problem Possible cause/Solution

The machine makes an un-

usual noise:

The machine is fitted with a type of motor which makes an unusual noise

compared with other traditional motors. This new motor ensures a softer

start and more even distribution of the laundry in the drum when spin-

ning, as well as increased stability of the machine.

No water is visible in the

drum:

Machines based on modern technology operate very economically using

very little water without affecting performance.

If you are unable to identify or solve the prob-

lem, contact our service centre. Before tele-

phoning, make a note of the model, serial num-

ber and purchase date of your machine: the

Service Centre will require this information.

Mod. ... ... ...

Prod. No. ... ... ...

Ser. No. ... ... ...

. ..

...

Prod. N

...

... ..

... ...

...

Technical data

Dimensions Width

Height

Depth

Depth (Overall dimensions)

60 cm

85 cm

55.3 cm

64.2 cm

Electrical connection

Voltage - Overall power - Fuse

Information on the electrical connection is given on the rating plate, on

the inner edge of the appliance door.

Water supply pressure Minimum

Maximum

0,05 MPa

0,8 MPa

Maximum Load Cotton 6 kg

Spin Speed Maximum 1000 rpm

Installation

Unpacking

Caution! All transit bolts and packing

must be removed before using the

appliance.

You are advised to keep all transit devices

so that they can be refitted if the machine

ever has to be transported again.

After removing all the

packaging, carefully

lay machine on it's

back.

Remove the polystyr-

ene base from the

bottom.

www.zanussi.com

Remove the power supply cable and the ho-

ses from the hose holders on the rear of the

appliance.

Unscrew the three

bolts

Slide out the relevant

plastic spacers

Open the porthole

and remove the poly-

styrene block fitted

on the door seal.

Plug the 3 holes with

the corresponding

plastic caps supplied

in the bag containing

the instruction book-

let.

Positioning

Install the machine on a flat hard floor. Make

sure that air circulation around the machine is

not impeded by carpets, rugs etc. Check that

the machine does not touch the wall or other

kitchen units.

Level the washing

machine by raising or

lowering the feet. The

feet may be tight to

adjust as they incor-

porate a self locking

nut, but the machine

MUST be level and

stable. If necessary,

check the setting with

a spirit level.

Any necessary ad-

justment can be

made with a spanner.

Accurate levelling prevents vibration, noise and

displacement of the machine during operation.

Caution! Never place cardboard, wood or

similar materials under the machine to

compensate for any unevenness in the floor.

After having levelled the appliance, tighten the

lock nuts.

Rubber feet kit (4055126249)

Available from your authorized dealer.

The rubber feet are particularly recommended

on floating, slippery and wooden floors.

Mount the rubber feet to prevent vibration,

noises and displacement of the appliance dur-

ing operation.

Read carefully the instructions supplied with

the kit.

Water inlet

Warning! This appliance must be

connected to a cold water supply

Caution! Before connecting up the

appliance to new pipework or to pipework

that has not been used for some time, run off a

reasonable amount of water to flush out any

debris that may have collected

www.zanussi.com

La page charge ...

Zanussi ZWG5100 Manuel utilisateur

Marque: Zanussi

Modèle: ZWG5100

Catégorie: Machines à laver

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Zanussi ZWG5100 User manual

Zanussi ZWG5100 Manuel utilisateur

Zanussi ZWG5100 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents