Jenn-Air Range 8113P529-60 Manuel utilisateur

JENN-AIR

®

GAS

DOWNDRAFT SLIDE-IN RANGE

Important Safety Instructions .....................................1-4

Ducting Information........................................................... 5

Care & Cleaning ..............................................................5-8

Maintenance.....................................................................8-9

Troubleshooting ......................................................... 10-11

Surface Cooking......................................................... 12-14

Oven Cooking.............................................................. 15-20

Options .......................................................................... 21-23

Favorites ........................................................................ 23-24

Setup .............................................................................. 24-26

Accessories .........................................................................26

Warranty & Service...........................................................27

Guide d’utilisation et d’entretien .................................28

Guía de uso y cuidado ....................................................58

USE & CARE

GUIDE

TABLE OF CONTENTS

®

8113P529-60 11/11/05, 3:55 PM1

1

Installer: Please leave this guide with this appliance.

Consumer: Please read and keep this guide for future

reference. Keep sales receipt and/or cancelled check as

proof of purchase.

Model Number __________________________________

Serial Number __________________________________

Date of Purchase ________________________________

If you have questions, call:

Jenn-Air Customer Assistance

1-800-JENNAIR (1-800-536-6247)

1-800-688-2080 (U.S. TTY for hearing or speech impaired)

(Mon.-Fri., 8 am-8 pm Eastern Time)

Internet: http://www.jennair.com

In our continuing effort to improve the quality and

performance of our cooking products, it may be necessary

to make changes to the appliance without revising this

guide.

For service information, see page 27.

IMPORTANT SAFETY

INSTRUCTIONS

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible conditions

and situations that may occur. Common sense, caution,

and care must be exercised when installing,

maintaining, or operating the appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words, Labels

WARNING – Hazards or unsafe practices which

COULD result in severe personal injury or death.

CAUTION – Hazards or unsafe practices which

COULD result in minor personal injury.

WARNING

CAUTION

Read and follow all instructions before using this

appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a

result of improper usage of the appliance. Use appliance

only for its intended purpose as described in this guide.

To ensure proper and safe operation: Appliance

must be properly installed and grounded by a qualified

General Instructions

WARNING: To reduce risk of

tipping of the appliance from

abnormal usage or by excessive loading of the

oven door, the appliance must be secured by a

properly installed anti-tip device.

WARNING

• ALL RANGES CAN TIP AND

CAUSE INJURIES TO PERSONS

• INSTALL ANTI-TIP DEVICE

PACKED WITH RANGE

• FOLLOW ALL INSTALLATION

INSTRUCTIONS

technician. Do not attempt to adjust, repair, service,

or replace any part of your appliance unless it is

specifically recommended in this guide. All other

servicing should be referred to a qualified servicer.

Always disconnect power to appliance before servicing.

If the information in this guide is not followed

exactly, a fire or explosion may result causing

property damage, personal injury or death.

– Do not store or use gasoline or other flam-

mable vapors and liquids in the vicinity of this

or any appliance.

– IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the fire department.

– Installation and service must be performed by

a qualified installer, service agency or the gas

supplier.

WARNING

Gas leaks may occur in your system and result in a

dangerous situation. Gas leaks may not be detected

by smell alone. Gas suppliers recommend you

purchase and install an UL approved gas detector.

Install and use in accordance with the manufacturer’s

instructions.

WARNING

To check if device is properly installed, look underneath

range with a flashlight to make sure one of the rear

8113P529-60 11/11/05, 3:55 PM2

2

leveling legs is properly engaged in the bracket slot. The

anti-tip device secures the rear leveling leg to the floor

when properly engaged. You should check this anytime

the range has been moved.

To Prevent Fire or

Smoke Damage

Be sure all packing materials are removed from the

appliance before operating it.

Keep area around appliance clear and free from

combustible materials. Flammable materials should not

be stored in an oven.

Many plastics are vulnerable to heat. Keep plastics away

from parts of the appliance that may become warm or

hot. Do not leave plastic items on the cooktop as they

may melt or soften if left too close to the vent or a

lighted surface burner.

To prevent grease fires, do not let cooking grease or

other flammable materials accumulate in or near the

appliance.

If appliance is installed near a window, proper

precautions should be taken to prevent curtains from

blowing over burners.

NEVER leave any items on the cooktop. The hot air from

the vent may ignite flammable items and may increase

pressure in closed containers which may cause them to

burst.

Many aerosol-type spray cans are EXPLOSIVE when

exposed to heat and may be highly flammable. Avoid

their use or storage near an appliance.

To eliminate the hazard of reaching over hot surface

burners, cabinet storage should not be provided

directly above a unit. If storage is provided, it should be

limited to items which are used infrequently and which

are safely stored in an area subjected to heat from an

appliance. Temperatures may be unsafe for some items,

such as volatile liquids, cleaners or aerosol sprays.

In Case of Fire

Turn off appliance and ventilating hood to avoid

spreading the flame. Extinguish flame, then turn on

hood to remove smoke and odor.

• Cooktop: Smother fire or flame in a pan with a lid or

cookie sheet.

NEVER pick up or move a flaming pan.

• Oven: Smother fire or flame by closing the oven door.

Do not use water on grease fires. Use baking soda, a

dry chemical or foam-type extinguisher to smother fire

or flame.

CAUTION

NEVER store items of interest to children in cabinets

above an appliance or on backguard of a range.

Children climbing on the appliance door to reach items

could be seriously injured.

NEVER leave children alone or unsupervised near the

appliance when it is in use or is still hot. Children should

never be allowed to sit or stand on any part of the

appliance as they could be injured or burned.

Children must be taught that the appliance and utensils in

it can be hot. Let hot utensils cool in a safe place, out of

reach of small children. Children should be taught that an

appliance is not a toy. Children should not be allowed to

play with controls or other parts of the appliance.

About Your Appliance

Child Safety

WARNING

NEVER use appliance door as a step stool or seat as this

may result in possible tipping of the appliance and serious

injuries.

NEVER use this appliance as a space heater to heat or

warm a room. Doing so may result in carbon

monoxide poisoning and overheating of the oven.

NEVER cover any slots, holes or passages in the oven

bottom or cover the entire rack with materials such as

aluminum foil. Doing so blocks air flow through the

oven and may cause carbon monoxide poisoning.

Aluminum foil may also trap heat, causing a fire

hazard.

NEVER obstruct the flow of combustion and ventilation

air by blocking the oven vent or air intakes. Doing so

restricts air to the burners and may result in carbon

monoxide poisoning.

Avoid touching oven vent area while oven is on and for

several minutes after oven is turned off. Some parts of

the vent and surrounding area become hot enough to

cause burns. After oven is turned off, do not touch the

oven vent or surrounding areas until they have had

sufficient time to cool.

Other potentially hot surfaces include cooktop, areas

facing the cooktop, oven vent, surface near the vent

opening, oven door, area around the oven door and oven

window.

Cont.

8113P529-60 11/11/05, 3:55 PM3

3

To prevent potential hazard to the user and damage to

the appliance, do not use appliance as a space heater to

heat or warm a room. Also, do not use the oven as a

storage area for food or cooking utensils.

NEVER use aluminum foil to cover an oven rack or oven

bottom. Misuse could result in risk of electric shock, fire,

or damage to the appliance. Use foil only as directed in

this guide.

Cooking Safety

Always place a pan on a surface burner before turning it

on. Be sure you know which knob controls which surface

burner. Make sure the correct burner is turned on and

that the burner has ignited. When cooking is completed,

turn burner off before removing pan to prevent exposure

to burner flame.

Always adjust surface burner flame so that it does not

extend beyond the bottom edge of the pan. An excessive

flame is hazardous, wastes energy and may damage the

appliance, pan or cabinets above the appliance.

NEVER leave a surface cooking operation unattended,

especially when using a high heat setting or when deep

fat frying. Boilovers cause smoking and greasy spillovers

may ignite. Clean up greasy spills as soon as possible.

Do not use high heat for extended cooking operations.

NEVER heat an unopened container on the surface

burner or in the oven. Pressure build-up may cause

container to burst resulting in serious personal injury or

damage to the appliance.

Use dry, sturdy potholders. Damp potholders may cause

burns from steam. Dish towels or other substitutes

should never be used as potholders because they can

trail across hot surface burners and ignite or get caught

on appliance parts.

Always let quantities of hot fat used for deep fat frying

cool before attempting to move or handle.

Do not let cooking grease or other flammable materials

accumulate in or near the appliance, hood or vent fan.

Clean hood frequently to prevent grease from

accumulating on hood or filter. When flaming foods

under the hood, turn the fan on.

NEVER wear garments made of flammable material or

loose fitting or long-sleeved apparel while cooking.

Clothing may ignite or catch utensil handles.

Utensil Safety

Use pans with flat bottoms and handles that are easily

grasped and stay cool. Avoid using unstable, warped,

easily tipped or loose-handled pans. Also avoid using

pans, especially small pans, with heavy handles as they

could be unstable and easily tip. Pans that are heavy to

move when filled with food may also be hazardous.

Be sure utensil is large enough to properly contain food

and avoid boilovers. Pan size is particularly important in

deep fat frying. Be sure pan will accommodate the

volume of food that is to be added as well as the bubble

action of fat.

To minimize burns, ignition of flammable materials and

spillage due to unintentional contact with the utensil, do

not extend handles over adjacent surface burners.

Always turn pan handles toward the side or back of the

appliance, not out into the room where they are easily hit

or reached by small children.

Never let a pan boil dry as this could damage the utensil

and the appliance.

Always place oven racks in the desired positions while

oven is cool. Slide oven rack out to add or remove food,

using dry, sturdy potholders. Always avoid reaching into

the oven to add or remove food. If a rack must be

moved while hot, use a dry potholder. Always turn the

oven off at the end of cooking.

Use care when opening the oven door. Let hot air or

steam escape before moving or replacing food.

PREPARED FOOD WARNING: Follow food

manufacturer’s instructions. If a plastic frozen food

container and/or its cover distorts, warps, or is otherwise

damaged during cooking, immediately discard the food

and its container. The food could be contaminated.

NEVER use aluminum foil to cover oven racks or oven

bottom. This could result in risk of electric shock, fire, or

damage to the appliance. Use foil only as directed in this

guide.

Do not touch a hot oven light bulb with a damp cloth as

the bulb could break. Should the bulb break, disconnect

power to the appliance before removing bulb to avoid

electrical shock.

Follow the manufacturer’s directions when using oven

cooking bags.

Only certain types of glass, glass/ceramic, ceramic or

glazed utensils are suitable for cooktop or oven usage

without breaking due to the sudden change in

temperature. Follow manufacturer’s instructions when

using glass.

This appliance has been tested for safe performance

using conventional cookware. Do not use any devices

or accessories that are not specifically recommended in

8113P529-60 11/11/05, 3:55 PM4

4

CAUTION

Do not clean door gasket. The door gasket is essential

for a good seal. Care should be taken not to rub,

damage, or move the gasket.

Do not use oven cleaners or oven liners of any kind in or

around any part of the self-clean oven.

Important Safety Notice

and Warning

The California Safe Drinking Water and Toxic

Enforcement Act of 1986 (Proposition 65) requires the

Governor of California to publish a list of substances

known to the State of California to cause cancer or

reproductive harm, and requires businesses to warn

customers of potential exposures to such substances.

Users of this appliance are hereby warned that when

the oven is engaged in the self-clean cycle, there may

be some low-level exposure to some of the listed

substances, including carbon monoxide. Exposure to

these substances can be minimized by properly venting

the oven to the outdoors by opening the windows and/

or door in the room where the appliance is located

during the self-clean cycle.

IMPORTANT NOTICE REGARDING PET BIRDS:

Never keep pet birds in the kitchen or in rooms where

the fumes from the kitchen could reach. Birds have a

very sensitive respiratory system. Fumes released during

an oven self-cleaning cycle may be harmful or fatal to

birds. Fumes released due to overheated cooking oil, fat,

margarine and overheated non-stick cookware may be

equally harmful.

Save These Instructions for Future Reference

this guide. Do not use element covers for the surface

units, stovetop grills, or add-on oven convection

systems. The use of devices or accessories that are not

expressly recommended in this guide can create serious

safety hazards, result in performance problems, and

reduce the life of the components of the appliance.

Deep Fat Fryers

Use extreme caution when moving the grease pan or

disposing of hot grease. Allow grease to cool before

attempting to move pan.

Ventilating Hoods

Clean range hood and filters frequently to prevent

grease or other flammable materials from accumulating

on hood or filter and to avoid grease fires.

When flaming foods under the hood, turn the fan on.

Cleaning Safety

Clean cooktop with caution. Turn off all controls and

wait for appliance parts to cool before touching or

cleaning. Use care to avoid steam burns if a wet sponge

or cloth is used to wipe spills on a hot surface. Some

cleaners can produce noxious fumes if applied to a hot

surface.

Clean only parts listed in this guide.

Self-Clean Oven

Before self-cleaning the oven, remove the oven racks,

broiler pan, food and any other utensils. Wipe

spillovers to prevent excessive smoke and flare-ups.

8113P529-60 11/11/05, 3:55 PM5

5

Jenn-Air’s ventilation system is designed to capture both

cooking fumes and smoke from the cooktop surface. If

the system does not, here are some ducting installation

situations to check:

• 6” diameter round or 3

1

/

4

” x 10” rectangular ducting

should be used for duct lengths 10’-60’.

• There should be a minimum clearance of 6” for

cooktop installed near a side wall.

If there is not an obvious improper installation, there

may be a concealed problem such as a pinched joint,

obstruction in the pipe, etc. Installation is

the responsibility of the installer and

questions should be addressed first by the

installer. The installer should very carefully

check the ducting installation instructions.

• Use the Flow Tester Card provided with

your appliance to check the air flow.

DUCTING INFORMATION

6

Cont.

3. Select CONTINUE using the Quickset pad. The Quickset

pads are located on either side of the control panel dsplay.

4. Set LIGHT soil level by entering 200 using the number

pads for two hours of cleaning time. Press the Enter pad.

OR

Select MEDIUM for a moderately soiled oven and three

hours of cleaning time.

To Delay a Self-Clean Cycle:

1. Press Clean pad.

2. REMOVE RACKS will be displayed.

Remove the racks.

3. Select CONTINUE using the Quickset pad..

4. Set LIGHT soil level by entering 200 using the number

pads for two hours of cleaning time. Press the Enter pad.

OR

Select MEDIUM for a moderately soiled oven and three

hours of cleaning time.

OR

Select HEAVY for a heavily soiled oven and four hours of

cleaning time.

5. The door will lock. CLEAN, TIME, LOCKED and the

cleaning time countdown will be displayed

Notes:

• If the oven door is left open, CLOSE DOOR will appear in

the display until the door is closed.

• If more than 30 seconds elapse between pressing the

Clean pad and pressing a number pad, the program will

automatically return to the previous display.

• The oven door will be damaged if it is forced to open

during cleaning or cooling process.

• The first few times the oven is cleaned, some smoke and

odor may be detected. This is normal and will lessen or

disappear with use. If the oven is heavily soiled, or if the

broiler pan was accidently left in the oven, excessive

smoke and odor may occur.

• As the oven heats and cools, you may hear sounds of

metal parts expanding and contracting. This is normal

and will not damage your appliance.

6. After door locks, press the More Options pad.

7. Select DELAY using the Quickset pad.

8. Select the number of hours you want to delay the start of the

self-clean cycle.

9. The delay time and cleaning time will be displayed.

After Self-Cleaning

About one hour after the end of the clean cycle, the lock

will disengage and OVEN COOLING will go off in the

display. At this point, the door can be opened.

Some soil may leave a light gray, powdery ash which can be

removed with a damp cloth. If soil remains, it indicates that

the clean cycle was not long enough. The soil will be removed

during the next clean cycle.

If the oven racks were left in the oven and do not slide

smoothly after a clean cycle, wipe racks and embossed rack

supports with a small amount of vegetable oil to restore ease

of movement.

A white discoloration may appear after cleaning if acidic or

sugary foods were not wiped up before the clean cycle. This is

normal and will NOT affect performance.

OR

Select HEAVY for a heavily soiled oven and four hours of

cleaning time.

5. CLEAN, TIME, LOCKED and the cleaning time countdown

will be displayed while the oven is cleaning. OVEN

COOLING will appear in the display when the cleaning

time has been completed and the oven is still locked.

Important: The door lock will disengage approximately one

hour after the cleaning time is completed. OVEN COOLING

will go off in the display when the oven door has unlocked.

7

PART PROCEDURE

CAUTION

Cleaning Procedures

• Be sure appliance is off and all parts are cool before handling

or cleaning. This is to avoid damage and possible burns.

• To prevent staining or discoloration, clean appliance after each use.

• If a part is removed, be sure it is correctly replaced.

* Brand names are registered trademarks of the

respective manufacturers.

** To order call 1-800-JENNAIR (1-800-536-6247).

Broiler Pan Never cover insert with aluminum foil as this prevents the fat from draining to the pan below.

and Insert • Place soapy cloth over insert and pan; let soak to loosen soil.

• Wash in warm, soapy water. Use scouring pad to remove stubborn soil.

• Broiler pan and insert can be cleaned in dishwasher.

Burner Caps Removable Burner Caps

and Sealed • Allow burner to cool. Remove burner cap and wash in soapy water with a plastic scouring pad. For

Gas Burners stubborn soils, clean with a soap-filled, nonabrasive pad or Cooktop Cleaning Creme*

(Part #20000001)** and a sponge.

• Do not clean in the dishwasher or self-cleaning oven.

Sealed Gas Burners

• Clean frequently. Allow burner to cool. Clean with soap and plastic scouring pad. For stubborn or

dried-on soils, clean with a soap-filled, nonabrasive pad, stiff brush, toothbrush, the soft rubber tip on

the toothbrush (if equipped) or a straight pin. Do not enlarge or distort holes.

• Be careful not to get water into burner ports.

• Use care when cleaning the ignitor. If the ignitor is wet or damaged the surface burner will not light.

Burner Grates - • Wash with warm, soapy water and a nonabrasive, plastic, scrubbing pad. For stubborn soils,

Porcelain on clean with a soap-filled, nonabrasive, plastic pad or Cooktop Cleaning Creme* and a sponge. If soil

Cast Iron remains, reapply Cooktop Cleaning Creme*, cover with a damp paper towel and soak for 30 minutes.

Scrub again, rinse and dry.

• Do not clean in the dishwasher or self-cleaning oven.

Cooktop – Porcelain enamel is glass fused on metal and may crack or chip with misuse. It is acid-resistant, not acid-

Porcelain proof. All spillovers, especially acidic or sugary spillovers, should be wiped up immediately with a dry cloth.

Enamel • When cool, wash with soapy water, rinse and dry.

• Never wipe off a warm or hot surface with a damp cloth. This may cause cracking or chipping.

• Never use oven cleaners, abrasive or caustic cleaning agents on exterior finish of range.

Clock and • To activate control lock for cleaning, see Locking the Control, page 16.

Control Pad • Wipe with damp cloth. Dry thoroughly.

Area • Glass cleaners may be used if sprayed on a cloth first. DO NOT spray directly on control pads and

display area.

• Do not use other cleaning sprays, abrasive cleaners or large amounts of water on the panel.

Control Knobs • Remove knobs in the OFF position by pulling forward.

• Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish.

• Turn on each element to be sure the knobs have been correctly replaced.

Oven Window • Avoid using excessive amounts of water which may seep under or behind glass, causing staining.

and Door - • Wash with soap and water. Rinse with clear water and dry. Glass cleaner can be used if sprayed on a cloth.

Glass • Do not use abrasive materials such as scouring pads, steel wool or powdered cleaners as they will scratch.

Oven Interior • Follow instructions on pages 5-6 to set a self-clean cycle.

Oven Racks • Clean with warm, soapy water.

• Remove stubborn soil with cleansing powder or soap-filled scouring pad. Rinse and dry.

• Racks will permanently discolor and may not slide smoothly if left in the oven during a self-clean

operation. If this occurs, wipe the rack edge and rack support with a small amount of vegetable oil to

restore ease of movement, then wipe off excess oil.

8113P529-60 11/11/05, 3:55 PM8

8

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

** To order direct, call 1-800-JENNAIR (1-800-536-6247).

PART PROCEDURE

Side Panels, • When cool, wash with warm, soapy water, rinse and dry. Never wipe a warm or hot surface with a damp

and Door cloth as this may damage the surface and may cause a steam burn.

Handles - • For stubborn soil, use mildly abrasive cleaning agents such as baking soda paste or Bon Ami*. Do not use

Painted Enamel abrasive cleaners such as steel wool pads or oven cleaners. These products will scratch or permanently

damage the surface.

Note: Use a dry towel or cloth to wipe up spills, especially acidic or sugary spills. Surface may

discolor or dull if soil is not immediately removed. This is especially important for white surfaces.

Stainless Steel • DO NOT USE ANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH.

(select models) • DO NOT USE ABRASIVE OR ORANGE CLEANERS.

• ALWAYS WIPE WITH THE GRAIN WHEN CLEANING.

• Daily Cleaning/Light Soil –– Wipe with one of the following - soapy water, white vinegar/water solution,

Formula 409 Glass and Surface Cleaner* or a similar glass cleaner - using a sponge or soft cloth. Rinse

and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray* (Part No.

20000008)**.

• Moderate/Heavy Soil –– Wipe with one of the following - Bon Ami, Smart Cleanser, or Soft Scrub* -

using a damp sponge or soft cloth. Rinse and dry. Stubborn soils may be removed with a damp multi-

purpose Scotch-Brite* pad; rub evenly with the grain. Rinse and dry. To restore luster and remove streaks,

follow with Stainless Steel Magic Spray*.

• Discoloration –– Using a damp sponge or soft cloth, wipe with Cameo Stainless Steel Cleaner*. Rinse

immediately and dry. To remove streaks and restore luster, follow with Stainless Steel Magic Spray*.

CAUTION

Oven Door

NEVER place excessive weight on or stand on an open

oven door. This could cause the range to tip over, break

the door, or injure the user.

• NEVER attempt to open or close door or operate oven until

door is properly replaced.

• NEVER place fingers between hinge and front oven frame.

Hinge arms are spring mounted. If accidentally hit, the

hinge will slam shut against oven frame and could injure

your fingers.

To remove:

1. When cool, open the oven door

to the broil stop position

(opened about four inches).

2. Grasp door at each side. Do not

use the door handle to lift door.

3. Lift up evenly until door clears

hinge arms.

To replace:

1. Grasp door at each side.

MAINTENANCE

Cont.

2. Align slots in the door with the hinge arms on the range.

3. Slide the door down onto the hinge arms until the door is

completely seated on the hinges. Push down on the top

corners of the door to completely seat door on hinges.

Door should not appear crooked.

Important: The oven door on a new range may feel “spongy”

when it is closed. This is normal and will decrease with use.

Oven Window

To protect the oven door window:

1. Do not use abrasive cleaning agents such as steel wool

scouring pads or powdered cleansers as they may scratch

the glass.

2. Do not hit the glass with pots, pans, furniture, toys, or

other objects.

3. Do not close the oven door until the oven racks are in

place.

Scratching, hitting, jarring or stressing the glass may weaken

its structure causing an increased risk of breakage at a later

date.

8113P529-60 11/11/05, 3:55 PM9

9

Leveling Legs

ANTI-TIP BRACKET

LEVELING LEG

Be sure the anti-tip bracket secures one of the rear

leveling legs to the floor. This bracket prevents the range

from accidentally tipping.

Be sure the range is leveled when installed. If

the range is not level, turn the leveling legs,

located at each corner of the range, until range

is level.

ANTI-TIP BRACKET

LEVELING LEG

CAUTION

To assure the proper replacement bulb is used, order bulb

from Jenn-Air. Call 1-800-JENNAIR (1-800-536-6247), ask for

part number 74004458 - halogen bulb.

To Replace Oven Light Bulb:

1. Disconnect power to the oven.

2. When oven is cool, use fingertips to grasp edge of bulb

cover. Pull out and remove.

3. Carefully remove old bulb by pulling straight out of

ceramic base.

4. To avoid damaging or decreasing the life of the new bulb,

do not touch the bulb with bare hands or fingers. Hold

with a dry cloth or paper towel. Push new bulb prongs

straight into small holes of ceramic base.

5. Replace bulb cover by snapping into place.

6. Reconnect power to the oven. Reset clock.

Oven Light

CAUTION

• Disconnect power to oven before replacing light bulb.

• Allow oven to cool before replacing light bulb.

• Make sure bulb cover and bulb are cool before touching.

Removal of Gas Appliance

Gas appliance connectors used to connect this appliance to

the gas supply are not designed for continuous movement.

Once installed, DO NOT repeatedly move this gas appliance

for cleaning or to relocate. If this appliance has to be moved

and/or removed for servicing, follow the procedure described

in the installation instructions. For information, contact Jenn-

Air Customer Service at 1-800-JENNAIR (1-800-536-6247).

To prevent range from accidentally tipping, range must be

secured to the floor by sliding rear leveling leg into the anti-

tip bracket.

Electrical Connection

Appliances which require electrical

power are equipped with a three-prong

grounding plug which must be plugged

directly into a properly grounded three-

hole 120 volt electrical outlet.

Always disconnect power to appliance before servicing.

The three-prong grounding plug offers protection against

shock hazards. DO NOT CUT OR REMOVE THE THIRD

GROUNDING PRONG FROM THE POWER CORD PLUG.

If an ungrounded, two-hole or other type electrical outlet is

encountered, it is the personal responsibility of the

appliance owner to have the outlet replaced with a

properly grounded three-hole electrical outlet.

10

TROUBLESHOOTING

For most concerns, • Check if oven controls have been properly set.

try these first. • Check to be sure plug is securely inserted into receptacle.

• Check or re-set circuit breaker. Check or replace fuse.

• Check power supply.

Part or all of appliance does • Check if surface and/or oven controls have been properly set. See pgs. 12 & 17.

not work. • Check if oven door is unlocked after self-clean cycle. See pg. 6.

• Check if oven is set for a delayed cook or clean program. See pgs. 17 & 6.

• Check if Control Lock is activated. See pg. 16.

• Check if control is in Sabbath Mode. See pg. 25.

Clock, indicator words, and/or • Oven may be set for a Cook & Hold or delay function.

lights operate but oven does • Control Lock may have been set. See pg. 16.

not heat.

Surface burner fails to light. • Check to be sure unit is properly connected to power supply.

• Check for a blown circuit fuse or a tripped main circuit breaker.

• Check to be sure ignitor is dry and clicking. Burner will not light if ignitor is damaged,

soiled or wet. If ignitor doesn’t click, turn control knob OFF.

The flame is uneven. • Burner ports may be clogged.

Surface burner flame lifts • Check to be sure a pan is sitting on the grate above.

off ports.

Food is not broiling properly • Check oven rack positions. Food may be too close to flame.

or smokes excessively. • Aluminum foil was incorrectly used. Never line the broiler insert with foil.

• Trim excess fat from meat before broiling.

• A soiled broiler pan was used.

• Preheat oven for 2-3 minutes before placing food in the oven.

• Broil with the oven door closed.

Baking results are not as • Check the oven temperature selected. Make sure oven is preheated when recipe

expected or differ from or directions recommend preheat.

previous oven. • Make sure the oven vent has not been blocked. See page 20 for location.

• Check to make sure range is level.

• Temperatures often vary between a new oven and an old one. As ovens age, the oven

temperature often “drifts” and may become hotter or cooler. See page 25 for

instructions on adjusting the oven temperature. Important: It is not recommended

to adjust the temperature if only one or two recipes are in question.

• Use correct pan. Dark pans produce dark browning. Shiny pans produce light browning.

• Check rack positions and pan placement. Stagger pans when using two racks. Allow

1-2 inches between pans and oven wall.

• Check the use of foil in the oven. Never use foil to cover an entire oven rack. Place

a small piece of foil on the rack below the pan to catch spillovers.

Oven will not self-clean. • Check to make sure the cycle is not set for a delayed start. See pg. 6.

• Check if door is closed.

• Check if control is in Sabbath Mode. See pg. 25.

• Oven may be over 400° F. Oven temperature must be below 400° F to program a

clean cycle.

PROBLEM SOLUTION

Cont.

8113P529-60 11/11/05, 3:55 PM11

11

Oven did not clean properly. • Longer cleaning time may be needed.

• Excessive spillovers, especially sugary and/or acidic foods, were not removed prior

to the self-clean cycle.

Oven door will not unlock after • Oven interior is still hot. Allow about one hour for the oven to cool after the

self-clean cycle. completion of a self-clean cycle. The door can be opened when the LOCK indicator

word is not displayed.

• The control and door may be locked. See pg. 6.

There are no beeps and • Oven may be in Sabbath Mode. See page 25.

no display.

Moisture collects on oven • This is normal when cooking foods high in moisture.

window or steam comes from • Excessive moisture was used when cleaning the window.

oven vent.

There is a strong odor or light • This is normal for a new range and will disappear after a few uses. Initiating a clean

smoke when oven is turned on. cycle will “burn off” the odors more quickly.

• Turning on a ventilation fan will help remove the smoke and/or odor.

• Excessive food soils on the oven bottom. Use a self-clean cycle.

Ventilation system is not • Check on cross ventilation in room or make up air.

capturing smoke efficiently. • Outside wall cap may be trapped shut.

• Range may be improperly installed; check ducting information. See pg. 5.

• Air filter may be improperly installed. See pg. 14.

Fault Codes • The oven may detect a fault during programming or during operation. If a fault is

detected, the message FAULT DETECTED - PRESS POWER TO CLEAR or FAULT

DETECTED - PRESS ENTER TO TRY AGAIN may appear. Follow directions in the display.

If the fault reappears or does not clear, call an authorized servicer or the toll-free number

in the display.

• If the same operation is attempted before having the oven repaired, the message

FEATURE NOT AVAILABLE will appear. The feature will remain inoperable until service

is obtained.

• If the oven is heavily soiled, excessive flareups may result in a fault code during cleaning.

Press the CANCEL pad and allow the oven to cool completely, wipe out excess soil, then

reset the clean cycle. If the fault code reappears, contact an authorized servicer.

Noises may be heard. • The oven makes several low-level noises. You may hear the oven relays as they go on

and off. This is normal.

• As the oven heats and cools, you may hear sounds of metal parts expanding and

contracting. This is normal and will not damage your appliance.

SAb flashing and then • Oven is in Sabbath Mode. To cancel, press and hold the Setup pad for five seconds.

displayed continuously.

Cannot add another Favorite. • Favorites is full. To delete a favorite and add another, see page 23.

PROBLEM SOLUTION

8113P529-60 11/11/05, 3:55 PM12

12

SURFACE COOKING

Surface Controls

Pilotless Ignition

Pilotless ignition eliminates the

need for a constant standing

pilot light. Each surface burner

has a spark ignitor. Use care

when cleaning around the

surface burner.

If the surface burner does

not light, check if ignitor is

broken, soiled or wet.

Setting the controls:

The size and type of cookware will affect the heat setting.

1. Place a pan on the burner grate.

• The burner flame may lift off or appear separated from

the port if a pan is not placed on the grate.

2. Push in and turn the knob to the desired setting.

• A clicking (spark) sound will be heard and the burner

will light.

Important: Each surface burner is equipped to provide

automatic reignition if the flame should somehow get

blown out.

Operating During a

Power Failure

Surface Control Knobs

Use to turn on the surface burners. An infinite choice of heat

settings is available from Low to High. At the High setting a

detent or notch may be felt. The knobs can be set on or

between any of the settings.

Graphics next to the knob identify which burner

the knob controls. For example, the graphic at left

shows the right front burner location.

CAUTION

• If flame should go out during a cooking operation and

the burner does not reignite itself, turn the burner off. If a

strong gas odor is detected, open a window and wait five

minutes before relighting the burner.

• Be sure all surface controls are set in the OFF position

prior to supplying gas to the range.

• NEVER touch cooktop until it has cooled. Expect some

parts of the cooktop, especially around the burners, to

become warm or hot during cooking. Use potholders to

protect hands.

CAUTION

When lighting the surface burners, be sure all of the

controls are in the OFF position. Strike the match first and

hold it in position before turning the knob on.

13

Cooktop

Notes:

• A properly adjusted burner with clean ports will light

within a few seconds. If using natural gas, the flame

will be blue with a deeper blue inner cone.

If the burner flame is yellow or is noisy, the air/gas

mixture may be incorrect. Contact a service technician

to adjust. (Adjustments are not covered by the

warranty.)

With LP gas, slight yellow tips on the flames are

acceptable. This is normal and adjustment is not

necessary.

• With some types of gas, you may hear a “popping”

sound when the surface burner is turned off. This is a

normal operating sound of the burner.

• If the control knob is turned very quickly from High to

Low, the flame may go out, particularly if the burner is

cold. If this occurs, turn the knob to the OFF position,

wait several seconds and relight the burner.

• The flame should be adjusted so it does not extend

beyond the edge of the pan.

To prevent the cooktop from discoloring

or staining:

• Clean cooktop after each use.

• Wipe acidic or sugary spills as soon as the cooktop has

cooled as these spills may discolor the

porcelain.

Unlike a range with standard gas burners,

this cooktop does not lift up nor is it

removable. Do not attempt to lift the

cooktop for any reason.

Burner Grates

The grates must be properly positioned before cooking.

When installing the grates, place the tab ends toward the

center, matching the straight bars.

Improper installation of the grates may result in chipping of

the cooktop.

Sealed Burners

The sealed burners of your range are secured to the cooktop

and are not designed to be removed. Since the burners are

sealed into the cooktop, boilovers or spills will not seep

underneath the cooktop.

However, the burner should be cleaned after each use. The

cap portion of the burner is easily removed for cleaning. (See

page 7 for cleaning directions.)

The burner caps must be correctly placed on the burner base

for proper operation of the burner.

High Performance Burner

There is one 16,000 BTU* high speed burner on your range,

located in the right front position. This burner offers higher

speed cooking that can be used to quickly bring water to a

boil and for large-quantity cooking.

Low Turn Down Burner

This burner is located in the right rear

position. The Simmer setting can be

used to steam or poach foods, to cook

delicate sauces or continue cooking

covered foods. The ultra-low Melt

setting is best for melting

chocolate and butter.

Important: When using the normal settings

for preparing foods, it may take a few minutes for the cooking

area to cool to the Melt heat setting.

* BTU ratings will vary when using LP gas.

Dual Ring Burner (select models)

The cooking surface is equipped with a dual

ring burner located in the left front

position. To operate, push in on the

control knob and turn counterclockwise

to light the burner. Continue turning

until the desired setting is reached. The

lighting sequence is: inner burner on

High, then inner burner on Low, then both

rings on High, then both rings on Low.

14

15

OVEN COOKING

A Rapid Preheat Use to decrease preheating time.

B Convect Use for convection baking and roasting.

C Bake Use for baking and roasting.

D Broil Use for broiling and top browning.

E TIMER 1 Sets timer.

F Display Displays oven functions, options and

window time of day.

G TIMER 2 Sets timer.

H Number Pads Use to enter time and temperature,

or to enter Favorites names.

I Favorites Use to access, program or save

baking cycles.

J More Options Use to access additional features.

K Clean Use to set self-clean cycle.

L Setup Use to view or change factory

default settings.

M Vent Fan Activates the ventilation fan on

the cooktop.

N Oven Light Use to turn the oven light on or off.

O CANCEL Cancels all operations except Timer,

Clock, Favorites, Setup and Vent Fan.

P Quickset pads Use to select options in display

window (next to display window

on both sides).

The control panel is designed for ease in programming. The display window shows options for each function and moves from step

to step through the programming process. Control panel features vary by model. Oven display above is programmed for a bake

operation.

A B C D E F G H

Control Panel

Quickset Pads

Quickset pads are located on each side of the display window

and are used to select the desired function or option in the

display window. To select the option or function, press the

Quickset pad next to the word.

Important: Four seconds after entering the function,

option, number or letter, the function will automatically be

entered. If more than 30 seconds elapse between steps in

programming, the function will be canceled and the

display will return to the previous display.

Clock

Setting the Clock:

1. Press the Setup pad.

2. Select CLOCK using the Quickset pads.

3. Select TIME.

4. Enter the time using the number pads.

5. Press Enter pad.

6. Select AM or PM in 12 hour mode. (For 24 hour clock, see

page 16.)

7. To exit the Setup mode, press Setup pad.

If you need to back out of a function or option in the display,

press the Back pad. When your programming is complete,

press the Enter pad or wait four seconds and the function will

start automatically.

Up arrows indicate additional screens with additional options.

Press the Quickset pads next to the arrows to scroll through

the display.

I J K L M N O P

8113P529-60 11/11/05, 3:55 PM16

16

Activating and canceling the clock/day

of week display:

1. Press Setup pad.

2. Select CLOCK.

3. Press the arrow to scroll until DISABLE is displayed.

4. Select DISABLE.

5. Select TIME.

6. Select OFF to turn the clock display off, or select ON to turn

the clock display on.

7. Select OFF to turn the day of the week display off. Select

ON to turn the weekday display on.

8. To exit the Setup mode, press Setup pad.

Entering the day of the week:

1. Press Setup pad.

2. Select CLOCK.

3. Press the arrow to scroll until DAY is displayed.

4. Use Quickset arrow to scroll through the days.

5. Select day desired.

6. To exit the Setup mode, press Setup pad.

To set the clock for a 12 or 24 hour format:

The clock can be set to display time in either a 12 hour or 24

hour format.

1. Press the Setup pad.

2. Select CLOCK.

3. Use the arrow to scroll to the next screen.

4. Select 12/24 HOUR.

5. Select 12 HR or 24 HR.

6. To exit Setup mode, press Setup pad.

Timers

Setting the Timers (Timer 1 or Timer 2):

1. Press TIMER 1 or TIMER 2 pad.

2. Press one of the displayed times using the

Quickset pads, or press the number pads to

enter the desired time.

Important: Each press of the displayed time choices adds

additional time. For example, pressing “10 MIN” three

times provides 30 minutes on the timer (0:30).

3. Press Enter pad.

Changing the amount of time entered once the

Timer starts:

1. Press the TIMER 1 or TIMER 2 pad once.

2. Press the displayed times on the Quickset

pads repeatedly until the desired time is entered.

OR

3. Press the number pads to enter the new desired time.

4. Press Enter pad.

Canceling the Timer:

1. Press the TIMER 1 or TIMER 2 pad twice.

If both Timers are active:

If the desired Timer is already in the foreground, press once

for edit mode and twice to cancel the Timer. If the desired

Timer is not in the foreground, follow the steps below.

1. Press the desired TIMER pad once. The selected Timer will

come to the foreground.

2. Press the TIMER pad a second time to access the edit

mode in order to make changes.

3. Pressing the TIMER pad a third time will cancel the Timer.

Changing the Timer beeps:

The signal beeps for TIMER 1 and TIMER 2 can be changed.

The options available are two beeps every thirty seconds, two

beeps every sixty seconds or one beep only. The default

setting is one beep.

1. Press the Setup pad.

2. Select the arrow to scroll until TONES

is displayed.

3. Select TONES.

4. Select TIMERS TONES.

5. Select the desired timer beep format (2-30 SEC, 2-60 SEC

or 1 BEEP).

6. Press Setup pad to exit Setup mode.

Locking the Control and Oven Door

The oven control and oven door can be locked to prevent

accidental programming. If an oven function is currently

being used, the control and door cannot be locked.

To lock the control and door:

Press the Back and Enter pads at the same time, holding for

three seconds or until CONTROL LOCKED appears in the

display.

To unlock the control and door:

Press the Back and Enter pads at the same time, holding for

three seconds. UNLOCKING DOOR will appear in the display

when the control and door are unlocking.

8113P529-60 11/11/05, 3:55 PM17

17

Notes:

• If more than thirty seconds elapse between pressing a

pad and pressing a number pad, the display will return

to the previous display.

• Whenever the temperature appears in the display, the

oven is heating.

• To change the oven temperature during cooking, press

the Bake pad and select a displayed temperature or use

the number pads to enter the desired temperature.

• The oven will automatically shut off after 12 hours if it is

accidentally left on. To set a Sabbath Mode, see Sabbath

Mode, page 25.

Bake Options

• The temperature in the display will increase in 1°

increments until the oven reaches the preset

temperature. Allow about 15 minutes for the oven

to preheat.

• When the oven is preheated, the oven will beep and

PREHEAT will no longer be displayed.

3. At the end of cooking, turn the oven off by

pressing the CANCEL pad. Remove food

from the oven. The oven will continue

operating until the CANCEL pad is pressed.

Baking

To set Bake:

1. Press the Bake pad.

2. Select the oven temperature using the Quickset pads.

OR

Enter the desired temperature using the number pads.

Press Enter pad to set.

• The temperature can be set from 170° F to 550° F

in 5° increments.

• After three seconds, the oven will begin to preheat.

BAKE and PREHEAT will appear in the display along

with 100° or the actual oven temperature, whichever

is higher.

To set a Delay:

1. After Bake has been programmed, press

the More Options pad.

2. Select DELAY.

3. Select the amount of time you want to delay the start of

cooking using the displayed times or the number pads.

4. Select the amount of time you want to cook using the

displayed times or the number pads.

5. The display will show BAKE, the temperature, the delay

time and the cook time countdown.

6. When the delay time has expired, the oven will begin

heating. COOK TIME, the cook time countdown, PREHEAT,

BAKE and the actual oven temperature will be displayed.

CAUTION

Do not use delayed baking for highly perishable foods such

as dairy products, pork, poultry or seafood.

Cook & Hold and Delay options are available when baking.

When using the Cook & Hold option, the oven begins to heat

immediately after the control has been set. Then, the oven

cooks for a specified length of time. When that time has

elapsed, the oven will automatically reduce temperature to

170° F and keep the food warm for up to an hour and then

automatically turn off.

When using Delay, the oven begins to cook later in the day.

Set the amount of time that you want to delay before the oven

turns on and how long you want to cook. The oven begins to

Notes:

• The oven control comes from the factory set for Auto

Convect Conversion. When using Convect Bake enter the

conventional baking temperature. The control

automatically converts the temperature to 25° less than

the conventional temperature.

• When using Convect Roast the temperature will not be

automatically reduced. Enter the conventional roasting

temperature and time. The control then lets you know

when 75% of the time has elapsed and alerts you to check

the food for doneness.

• To turn Auto Convect Conversion off, see page 24.

18

Convect Bake

To set Convect Bake:

1. Press the Convect pad.

2. Select CNVT BAKE using the Quickset pads.

3. Select the oven temperature using the Quickset pads

19

Broil

For optimal results, preheat for five minutes with the door

closed and use a pan designed for broiling. Oven door should

be open to the broil stop position (about 4 inches) when

broiling.

To set Broil:

1. Place the oven rack in the proper rack position (see

Broiling Chart).

2. Press the Broil pad.

3. Select HIGH – 550° F for high broil.

OR

Select LOW – 450° F for low broil.

• The oven has a variable broil feature which means that

a lower broil temperature can be selected (300°-550° F).

To select a lower temperature, press the appropriate

number pads. Press Enter pad to set the lower

temperature.

4. Preheat the oven for five minutes.

5. Place food in the oven and close the door to the broil stop

position.

6. Press the CANCEL pad when broiling

is done.

Notes:

• See Broiling Chart for foods and broiling times.

• If more than 30 seconds elapse between pressing the Broil

pad, Quickset pads, or number pads, the oven will not be

set and the display will return to the previous display.

• HIGH is used for most broiling. Use a lower broil

temperature when broiling longer-cooking foods. The

lower temperature allows food to cook to the well done

stage without excessive browning.

• Expect broil times to increase and browning to be slightly

lighter if the appliance is installed on a 208 volt circuit.

• Food should be turned halfway through broiling time.

• Broil times may be longer when lower broiling

temperatures are selected.

Notes:

• For best results, use rack position 2 or 3 when using the

Rapid Preheat option.

• For optimum baking and browning results, Rapid Preheat

is not recommended when baking on multiple racks.

SUGGESTED RACK

FOODS BROIL TIME POSITION*

Beef (broiled to 165° F)

6 Hamburgers, 1/2” thick 10 – 12 minutes 4

2 Ribeye Steaks, 1” thick 18 - 22 minutes 4

2 New York Strip Steaks, 1” thick 18 - 22 minutes 4

2 T-Bone Steaks, 1” thick 18 - 22 minutes 4

Poultry (broiled to 170° F on Low) Low Broil

4 Boneless/Skinless Breasts 12 – 15 minutes 4

4 Bone-In Chicken Breasts 20 – 33 minutes 3

Pork (broiled to 160° F)

4 Boneless Pork Chops, 1” thick 20 - 28 minutes 4

4 Bone-In Pork Chops, 1” thick 25 - 28 minutes 4

Ham Slice, 1” thick 12 - 16 minutes 4

Fish (broiled to 140° F)

4 Swordfish Steaks, 1” thick 10 - 14 minutes 3

2 Halibut Steaks, 1” thick 10 - 14 minutes 3

Orange Roughy, 1 ” thick 10 - 12 minutes 4

Shrimp (16-20 ct. per lb.) 8 - 10 minutes 4

2 Salmon Fillets, 1/2” thick 8 - 12 minutes 4

2 Salmon Steaks, 1” thick 10 - 14 minutes 3

*Important: To reduce browning and excess smoke when broiling, use a lower rack position and increase

the broil time.

Broiling Chart

8113P529-60 11/11/05, 3:55 PM20

La page charge ...

Jenn-Air Range 8113P529-60 Manuel utilisateur

Jenn-Air Range 8113P529-60 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents