Hunter Fan 83701 Le manuel du propriétaire

42909-01 02/12/2008

1

I n s t a l l a t i o n G u i d e

83701 Riazzi Bath Ventilator with Light

READ and SAVE THESE INSTRUCTIONS

ENGLISH

See page 2

FRANçAIS

Consulter la page 21

011_42909_EngF_2-12-08.indd 1 2/12/08 2:56:06 PM

42909-01 02/12/2008

2

DISCONNECT ELECTRIC

POWER SUPPLY

AND LOCK OUT

SERVICE PANEL BEFORE

SERVICING UNIT

W A R N I N G

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

1. For general ventilating use only. Do not use to exhaust hazard-

ous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy/unbalanced impellers,

keep drywall spray, construction dust, etc. off power unit.

3. DO NOT install this product in a wall. This product is designed

for installation in ceilings up to a 12/12 pitch (45 degrees).

Ductwork must point upward.

4. Pleasereadspecicationlabelonproductforfurtherinformation

and requirements.

PREVENTATIVE MAINTENANCE

A clean fan provides better service. Disconnect the power supply and

clean the fan as listed below.

TO CLEAN GRILLE: Use a mild detergent, such as dishwashing

liquid, and a soft cloth. DO NOT use abrasive cloths, steel wool pads

or scouring powders.

TO CLEAN FAN ASSEMBLY: Unplug motor cord from receptacle.

To remove motor plate, find the single tab on the motor plate (located

next to the receptacle). Push up rear motor plate tab while pushing

out on the side of the housing or insert a screwdriver into the slot in

the housing (next to tab) and twist screwdriver. Gently vacuum fan,

motor and interior of housing.

METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED

IN WATER.

MAINTENANCE

The motor is permanently lubricated and never needs oiling. If the

motor bearings are making excessive or unusual noises, replace the

motor with the exact service motor. You should replace the impeller at

the same time.

C A U T I O N

W A R N I N G

1. Use this unit only in a manner intended by the manufacturer.

If you have questions, contact the manufacturer.

2. Before servicing or cleaning the unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by quali-

edperson(s)inaccordancewithallapplicablecodesand

standards,includingre-ratedconstruction.

4. Sufcientairisneededforpropercombustionandexhausting

ofgassesthroughtheue(chimney)offuelburningequipment

to prevent backdrafting. Follow the heating equipment manufac-

turer’s guideline and safety standards,such as those published

by the National Fire Prevention Association (NFPA), and the

American Society for Heating, Refrigeration and Air-Conditioning

Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall(s) or ceiling, do not damage

electrical wiring or other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. If this unit is to be installed over a tub or shower, it must be

marked as appropriate for the application and be connected to a

GFCI (Ground Fault Circuit Interrupter) – protected branch circuit.

8. Never place a switch where it can be reached from a tub or

shower.

9. Installfanatleast5feet(1.52m)abovetheoor.

10. This unit must be grounded.

11. Unit must not be installed in a ceiling thermally insulated to a

value greater than R40.

Do Not Install Above

Or Inside This Area

Cooking

Equipment

Floor

45° 45°

COOKING AREA

011_42909_EngF_2-12-08.indd 2 2/12/08 2:56:06 PM

42909-01 02/12/2008

3

E

F

G

H

I

J

M

N

O

x5

*

NOTE:

Strain relief cable

connector must be

installed. Not Included.

A

B

C

95044-01-000

95022-01-000

75867-01-000

03242-07-133

95492-04-000

74508-03-133

96373-01-214

K

77520-01

L

65219

75184-01-133

96374-01-214

Extra Screws

x2

D

x2

3/8” Cable Connector

1

Turn off the power source.

Tools Needed. (Not supplied.)

Estimated assembly time: 30 to 60 minutes

Before Installation

Check all the parts.

If damaged, call

1-888-830-1326

for replacements.

Included.

2

F

J

Loosen screws.

NOTE: Remove all packing materials before installation.

011_42909_EngF_2-12-08.indd 3 2/12/08 2:56:08 PM

42909-01 02/12/2008

4

5

4

7

H

8

G

Remove the motor/blower from the housing.

3

I

F

Remove the pre-loaded screw tip covers.

Remove the wiring cover screw.

6

Back out the pre-loaded screw tips until flush

with the side of the housing.

Remove the wiring cover.

Remove packing material.

011_42909_EngF_2-12-08.indd 4 2/12/08 2:56:11 PM

42909-01 02/12/2008

5

9

F

Pop out the first wiring access slug. Use second if needed. Insert the strain relief (not Included) into the housing

and secure with washer.

Position the correct depth mark at the bottom edge of the

joist based on the thickness of your sheetrock.

New Construction - attaching to joist

10

B

C

Choose Installation Option

For New Construction - attaching to joist go to step A11, page 5

For New Construction - suspended between joists go to step B11, page 8

For Existing Construction - accessible from above go to step C11, page 11

For Existing Construction - accessible only from below go to step D11, page 15

A11

F

5/8

1/2

5/8

1/2

A12

Screw pre-loaded screws into joist or framing.

011_42909_EngF_2-12-08.indd 5 2/12/08 2:56:14 PM

42909-01 02/12/2008

6

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

Red

White

Black

White

Bare Copper

Ground

A14

Night Light

Switch 1 (AC In)

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

A13

0

A16

Route wires through strain relief. For supply connection, use

wires suitable for at least 90º C (194º F).

Connect wires as shown.

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may need

to be purchased.

H

A15

F

Install the wiring cover plate. Make sure all

wiring connections are inside the box or under

the wiring cover plate.

011_42909_EngF_2-12-08.indd 6 2/12/08 2:56:16 PM

42909-01 02/12/2008

7

A19

J

Secure the motor by tightening the 2 screws.

A20

Turn on the power source.

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

0000

A17

Reinstall the motor by inserting the tabs and pushing up into

position. Make sure the wires are not pinched

between the motor and the housing.

0000

I

A18

ON

OFF

A21

Test the motor. If the motor does not run, check the plug

connection.

A22

E1

Go to step

on page 17

to attach grille.

011_42909_EngF_2-12-08.indd 7 2/12/08 2:56:20 PM

42909-01 02/12/2008

8

5/8

1/2

5/8

1/2

B12

Slide the mounting rails into brackets.

Mark position of screws by using holes as a template.

Insert screws, leaving space between the screw

head and the joist. Screws are not provided.

New Construction – suspended between joists

B11

E

F

1/8” bit

B14

B15

F

B13

Position the correct depth mark at the bottom edge of

the joist based on the thickness of your sheetrock.

Drill a hole in the center of each outline.

Attach the rails onto the screws.

B16

011_42909_EngF_2-12-08.indd 8 2/12/08 2:56:23 PM

42909-01 02/12/2008

9

Tighten screws.

Route wires through strain relief. For supply connection, use

wires suitable for at least 90º C (194º F).

Connect wires as shown.

B17

B18

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

Red

White

Black

White

Bare Copper

Ground

B19

Night Light

Switch 1 (AC In)

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

B21

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may need

to be purchased.

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under the

wiring cover plate.

H

B20

G

011_42909_EngF_2-12-08.indd 9 2/12/08 2:56:26 PM

42909-01 02/12/2008

10

B27

E1

Go to step

on page 17

to attach grille.

B22

I

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

I

B23

Reinstall the motor by inserting the tabs and pushing up into

position. Make sure the wires are not pinched

between the motor and the housing.

B25

Turn on the power source.

ON

OFF

B26

B24

J

Test the motor. If the motor does not run,

check the plug connection.

Secure the motor by tightening the 2 screws.

011_42909_EngF_2-12-08.indd 10 2/12/08 2:56:30 PM

42909-01 02/12/2008

11

C12

E

F

Existing Construction – accessible from above

EXISTING FAN

C11

NO EXISTING FAN

9”

9.75”

OR

Remove an existing fan and check to make sure the

opening is large enough to accommodate the new

motor housing (9”x 9.75”).

Cut out an opening for the housing.

Use the motor housing as a template to mark position.

Slide the mounting rails into brackets.

Position the correct depth mark at the bottom edge of the

joist based on the thickness of your sheetrock.

5/8

1/2

5/8

1/2

C13

C14

Mark position of screws by using holes as a template.

011_42909_EngF_2-12-08.indd 11 2/12/08 2:56:33 PM

42909-01 02/12/2008

12

C17

C18

C19

C20

C15

C16

Drill a hole in the center of each outline. Insert screws, leaving space between the screw head

and the joist. Screws are not provided.

Attach the rails onto the screws. Tighten screws.

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may

need to be purchased.

Route wires through strain relief. For supply connection, use

wires suitable for at least 90º C (194º F).

011_42909_EngF_2-12-08.indd 12 2/12/08 2:56:37 PM

42909-01 02/12/2008

13

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

Red

White

Black

White

Bare Copper

Ground

C22

Night Light

Switch 1 (AC In)

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

Tighten the strain relief screws.

Connect wires as shown.

C24

I

H

C23

G

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under the

wiring cover plate.

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

C21

011_42909_EngF_2-12-08.indd 13 2/12/08 2:56:39 PM

42909-01 02/12/2008

14

C25

I

C26

J

C27

ON

OFF

C28

Secure the motor by tightening the 2 screws.

Turn on the power source.

Test the motor. If the motor does not run,

check the plug connection.

C29

E1

Go to step

on page 17

to attach grille.

Reinstall the motor by inserting the tabs and pushing up into

position. Make sure the wires are not pinched

between the motor and the housing.

011_42909_EngF_2-12-08.indd 14 2/12/08 2:56:42 PM

42909-01 02/12/2008

15

EXISTING FAN

D11

F

D12

Existing Construction – accessible only from below

D13

2

1

D14

Route wires through strain relief. For supply connection, use

wires suitable for at least 90º C (194º F).

Remove an existing fan and check to make sure the opening

is large enough to accommodate the new motor housing

(9”x 9.75”).

Move the housing into position above the ceiling

Attach existing ducting to duct connector. Tape joints.

If ducting does not fit securely,

an adapter may need to be purchased.

F

D15

Install the housing flush with the sheetrock and secure by

tightening the pre-loaded screws into the joist.

011_42909_EngF_2-12-08.indd 15 2/12/08 2:56:45 PM

42909-01 02/12/2008

16

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

Red

White

Black

White

Bare Copper

Ground

D16

Night Light

Switch 1 (AC In)

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

I

D18

I

D19

D20

J

Connect wires as shown.

Reinstall the motor by inserting the tabs and pushing up

into position. Make sure the wires are not pinched between

the motor and the housing.

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

Secure the motor by tightening the 2 screws.

H

D17

G

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under

the wiring cover plate.

011_42909_EngF_2-12-08.indd 16 2/12/08 2:56:48 PM

42909-01 02/12/2008

17

ON

OFF

D22

D23

E1

Go to step

on page 17

to attach grille.

D21

Test the motor. If the motor does not run,

check the plug connection.

Turn on the power source.

Attaching the Grille

Remove the thumbscrews. Connect wiring harness. DO NOT ALLOW THE FIXTURE TO

HANG FROM THE WIRING HARNESS.

N

F

E1

M

E2

011_42909_EngF_2-12-08.indd 17 2/12/08 2:56:51 PM

42909-01 02/12/2008

18

Position the strain relief bracket between the plugs as

shown, and screw into place.

K

E3

Align tabs on glass dome assembly with slots on light

fixture, and insert tabs into slots.

Install 2 Max 60 watt A-15 bulbs (Not Included).

E8

Turn glass dome assembly as shown until it locks

into position.

E6

O

E7

Attach thumbscrews.

WARNING: To reduce the risk of electrical shock,

all 4 thumbscrews MUST be properly installed.

N

E5

Align posts A, B, C and D (stamped into motor housing)

with posts A, B, C and D (stamped into light fixture).

Slide light fixture over posts.

M

E4

011_42909_EngF_2-12-08.indd 18 2/12/08 2:56:53 PM

42909-01 02/12/2008

19

Trouble Shooting

Problem: Fan does not come on.

Solution:

 •HunterFanBathVentilatorsareextremelyquiet.Toconrmthatthefanisrunning,placeyourhandneartheventstofeel

the air movement.

• Turn power on, replace fuse, or reset breaker.

• Check all plug connections to be sure they are secure.

• Check the wiring to make sure it matches the wiring diagram.

Problem: Light does not come on.

Solution:

• Replace the light bulb with a new bulb.

• Turn power on, replace fuse, or reset breaker.

• Check all plug connections to be sure they are secure.

• Check the wiring to make sure it matches the wiring diagram.

Problem: Fan is noisy.

Solution:

• Check and tighten all fasteners.

• Check the glass to make sure it is secure.

 •Checktheappertomakesureitmovesfreely.

If you need parts or service assistance, please call 888-830-1326 or visit us at our WEB site at http://www.hunterfan.com.

011_42909_EngF_2-12-08.indd 19 2/12/08 2:56:54 PM

42909-01 02/12/2008

20

2500 Frisco Avenue, Memphis, Tennessee 38114

Printed in China

Warranty

Hunter Fan Company

Bath Exhaust Fan

LIMITED WARRANTY

Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter bath exhaust fan:

IfanypartofyourHunterbathexhaustfan(exceptforglassxturesandlightbulbs)failsatanytimewithinoneyearafterthedateof

sale to you due to a defect in material or workmanship, we will repair or, at our option, replace the defective part free of charge for parts

and labor performed at our nearest service center or at our Service Department in Memphis, Tennessee. After this one-year period, you

will be responsible for all parts and labor costs for repairs on the bath exhaust fan except for motor repairs as provided below.

IfyourHunterbathexhaustfanmotorfailsatanytimewithinveyearsafterthedateofsaletoyouduetoadefectinmaterialorwork

-

manship, labor and materials to repair the defect will be provided free of charge at our nearest service center or our Service Department

in Memphis, Tennessee. If no replacement part can be provided, we will, at our option, either refund the actual purchase price of your

bathexhaustfanorprovideareplacementfreeofcharge.Afterthisve-yearperiod,youwillberesponsibleforallpartsandlaborcosts

for repairs on all parts of the bath exhaust fan.

IF THE ORIGINAL USER OR CONSUMER PURCHASER CEASES TO OWN THE FAN, THIS WARRANTY AND ANY IMPLIED

WARRANTY WHICH THEN REMAINS IN EFFECT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANT-

ABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE VOIDED. NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING ANY

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS MADE IN RESPECT OF GLASS FIXTURES

OR LIGHT BULBS OR THE FINISH ON ANY METAL PORTION OF THE BATH EXHAUST FAN.

THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THE DURATION OF ANY IMPLIED WARRANTY, INCLUD-

ING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IN

RESPECT TO ANY HUNTER FAN BATH EXHAUST FAN MOTOR OR OTHER FAN PART, IS EXPRESSLY LIMITED TO THE PERIOD

OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH MOTORS OR OTHER PARTS.

This warranty is voided if your Hunter bath exhaust fan is not purchased and installed in the U.S.A. This warranty excludes and does

not cover defects, malfunctions or failures of any Hunter bath exhaust fan which were caused by repairs by persons not authorized by

us,useofpartsoraccessoriesnotauthorizedbyus,mishandling,improperinstallation,modicationsordamagetotheHunterbath

exhaust fan while in your possession, or unreasonable use, including failure to provide reasonable and necessary maintenance.

To obtain servicing, contact the nearest Hunter authorized service center of the Hunter Fan Company Service Department, 2500 Frisco

Avenue, Memphis, Tennessee 38114. Please contact us before shipping your bath exhaust fan to us. If we authorize you to ship it to

us, you will be responsible for all insurance and freight or other transportation charges to our factory or service center. We will return

your Hunter bath exhaust fan freight prepaid. Your Hunter bath exhaust fan should be properly packed to avoid damage in transit since

we will not be responsible for any such damage. Proof of purchase is required when requesting warranty service. The purchaser must

present the sales receipt or other document that establishes proof of purchase.

IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITA-

TION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY TO

YOU.

THE WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE

TO STATE.

011_42909_EngF_2-12-08.indd 20 2/12/08 2:56:54 PM

La page charge ...

Hunter Fan 83701 Le manuel du propriétaire

Hunter Fan 83701 Le manuel du propriétaire

dans d''autres langues

Documents connexes