Continental Fireplaces 2100-1 Le manuel du propriétaire

FRENCH

PG. 41

W415-1929 / A / 10.21.19

ADD MANUAL TITLE

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.timberwolfﬁ replaces.com • ask@timberwolfﬁ replaces.com

ADD SAFETY STANDARD INFORMATION

& EPA QUALIFICATION (IF APPLICABLE)

Product Name / Code

(MUST use title from Price Book)

ADD ____ ILLUSTRATED

ADD PRODUCT IMAGE

SAFETY INFORMATION

- This heater can be very hot when burning.

- Combustible materials such as ﬁ rewood, wet clothing, etc. placed

too close can catch ﬁ re.

- Children and pets must be kept from touching the heater when it is

hot.

- The chimney must be sound and free of cracks. Before installing

this appliance, contact the local building or ﬁ re authority and follow

their guidelines.

- Operate only with the doors tightly closed.

- Burn wood behind the log retainer directly on the ﬁ rebricks.

- Do not use an elevated grate or otherwise raise the ﬁ re.

- This appliance is designed to burn natural wood only. Higher

efﬁ ciencies and lower emissions generally result when burning air

dried seasoned hardwoods, as compared to softwoods or to green

or freshly cut hardwoods.

- Do not start a ﬁ re with chemicals or ﬂ uids such as gasoline, engine

oil, etc.

- Do not burn trash or garbage, lawn clippings/waste, rubber,

waste petroleum products, paints or paint thinners/solvents, plastic,

materials containing asbestos, construction debris, railroad ties or

treated wood, manure or animal remains, salt water driftwood or

salted materials, unseasoned wood, coal, charcoal, coloured paper,

cardboard, plywood or particleboard. Burning these materials may

result in release of toxic fumes or render the appliance ineffective and

cause smoke.

- Do not let the appliance become hot enough for any part to glow

red.

If the information in these instructions are not followed exactly, a ﬁ re

or explosion may result causing property damage, personal injury or

death. Please read the entire manual before you install and use your

appliance. This heeater has not been tested with an unvented gas log

set. To reduce risk of ﬁ re or injury, do not install an unvented gas log

set into the heater.

WARNING

!

ENGLISH

$10.00

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

FOR INDOOR USE ONLY

This wood appliance needs periodic inspection and repair. It is against United States federal regulations to operate this wood

appliance in a manner inconsistent with the operating instructions in this manual.

Wood Stoves ONLY

- At least 14 squares inches (90.3 square centimeters) of outside air

must be admitted to the room or directly to the appliance through a

4” (101.6mm) diameter pipe.

- KEEP THE STOVE TOP TEMPERATURE BELOW 700°F (371°C).

Attempts to achieve heat output rates that exceed design

specifications can result in steel distortion and damage.

IF INSTALLATION + OPERATION, ADD SERIAL

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE

BARCODE LABEL ON THE OWNER’S MANUAL”

CSA / OMNI

/ INTERTEK

LOGO

U.S. ENVIRONMENTAL PROTECTION AGENCY (E.P.A.) CERTIFIED TO COMPLY WITH

2020 PARTICULATE EMISSION STANDARDS USING CORD WOOD. THIS APPLIANCE HAS

BEEN TESTED BY POLYTESTS AND LISTED BY OMNI-TEST LABORATORIES, INC. TO

STANDARDS: CSA B366.2, ULC S627, AND UL 1482. METHODS ALT-125

AS REFERENCED INTO 40 CFR PART 60 SUBPART AAA.

OMNI REPORT NUMBER 0415WS014E.

(2100-1 leg model illustrated)

INSTALLATION AND

OPERATION MANUAL

Timberwolf

®

Economizer Series

2100-1

W415-1929 / A / 10.21.19

EN

2

safety information

• This appliance is hot when operated and can cause

severe burns if contacted.

• Any changes or alterations to this appliance or its

controls can be dangerous and is prohibited.

• Do not operate appliance before reading and

understanding operating instructions. Failure

to operate appliance according to operating

instructions could cause ﬁ re or injury.

• Before installing this appliance, contact the local

building or ﬁ re authority and follow their guidelines.

• This appliance must be installed by a qualiﬁ ed

installer. Never try to repair or replace any part of the appliance unless instructions are given in this manual.

All other work should be done by a trained technician.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not operate without fully assembling all components. Do not install damaged, incomplete or substitute

components.

• Do not let the appliance become hot enough for any part to glow red.

• Risk of cuts and abrasions. Wear protective gloves, footwear and safety glasses during installation. Sheet

metal edges may be sharp.

• All wiring should be done by a qualiﬁ ed electrician and shall be in compliance with local codes. in the

absence of local codes, use the current CSA22.1 Canadian Electric Code in Canada or the current

National Electric Code ANSI/NFPA No. 70 in the United States.

• If equipped, burning your appliance with the ash dump door ajar creates a ﬁ re hazard that may result in

discolouration to the door, internal damage to the appliance or a house and/or chimney ﬁ re.

• Do not connect this appliance to a chimney ﬂ ue serving another appliance.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance. Objects placed in

front of the appliance must be kept a minimum of 48” (121.9cm) away from the front face of the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and

draperies.

• Even after the appliance is off, it will remain hot for an extended period of time.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• Under no circumstances should this appliance be modiﬁ ed.

• This appliance must not be connected to a chimney ﬂ ue pipe servicing a separate solid fuel burning

appliance.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass

should be done by a licensed or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• Only doors / optional fronts certiﬁ ed with the appliance are to be installed on the appliance.

• If the appliance is not properly installed, a house ﬁ re may result. Do not expose the appliance to the

elements (ex. rain, etc.) and keep the appliance dry at all times. Wet insulation will produce an odour when

the appliance is used.

• The chimney must be sound and free of cracks. Clean your chimney a minimum of twice a year and as

required.

• Children and adults should be alerted to the hazards of high surface temperature and should stay away to

avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier

is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,

install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the

room and away from hot surfaces.

• Ensure you have incorporated adequate safety measures to protect infants/toddlers from touching hot

surfaces.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from

hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with

all plastic bags, these are not toys and should be kept away from children and infants.

• Do not start a ﬁ re with chemicals or ﬂ uids such as gasoline, engine oil, etc.

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

!

WARNING

!

WARNING

EN

W415-1929 / A / 10.21.19

3

safety information

!

WARNING

• Your appliance requires periodic maintenance and cleaning. Failure to maintain your appliance may lead to smoke

spillage in your home.

• Ashes must be disposed in a metal container with a tight lid and placed on a non-combustible surface well

away from the home or structure until completely cool.

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.

Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage

to decorations, a TV or other electronic components.

For wood appliances:

• Lower emissions generally result when burning air dried seasoned hardwoods, as compared to softwoods

or too green or freshly cut hardwoods. Burning wet unseasoned wood can cause excessive creosote

accumulation. When this is ignited it can cause a chimney ﬁ re that may result in a serious house ﬁ re.

• This appliance is designed to burn natural wood only. Do not burn trash or garbage, lawn clippings /

waste, rubber, waste petroleum products, paints or paint thinners / solvents, plastic, materials containing

asbestos, construction debris, railroad ties or treated wood, manure or animal remains, salt water driftwood

or salted materials, unseasoned wood, coal, charcoal, coloured paper, gift wrapping, cardboard, plywood or

particleboard. Burning these materials may result in release of toxic fumes or render the appliance ineffective

and cause smoke.

• Burn wood directly on the ﬁ rebricks. Do not elevate grate or otherwise raise the ﬁ re.

• Do not store wood within appliance installation clearances or within the space required for re-fueling and

ash removal.

• If equipped, the catalyst must be installed and in good working order. It is recommended that the catalyst

is inspected at least three times per heating season.

Add California Prop 65 warning

!

WARNING:

This product can expose you to chemicals including lead and lead compounds,

which are known to the State of California to cause cancer, and chemicals including carbon

monoxide, which are known to the State of California to cause birth defects or other reproduc-

tive harm. For more information, go to www.P65Warnings.ca.gov.

W415-1929 / A / 10.21.19

EN

4

table of contents

1.0 general information 5

1.1 dimensions 5

1.2 speciﬁ cations 6

1.3 general instructions 6

1.4 general information 7

1.5 rating plate information 8

2.0 installation planning 9

2.1 appliance placement 9

2.2 minimum clearance to combustibles 9

2.3 alcove installation 10

2.4 ﬂ oor protection 10

2.5 outside air 10

3.0 installation 11

3.1 chimney 11

3.1.1 chimney connection 12

3.1.2 adding sections 13

3.1.3 typical through the ceiling 14

3.1.4 typical through the wall 15

3.1.5 typical existing masonry 16

4.0 finishing 17

4.1 leg installation 17

4.2 pedestal installation 18

4.3 door removal 18

4.4 door handle installation 19

4.5 secondary air tubes 20

4.6 brick and bafﬂ e installation 21

4.7 ash lip installation 22

5.0 optional installation 23

5.1 blower kit installation 23

5.2 ash drawer kit (EP20LAD) 24

5.3 ash pan kit (EP20PAD) 25

6.0 operation 26

6.1 optimum burn method 27

6.2 air control 27

6.3 ﬁ re extinguishers / smoke & carbon

monoxide detectors 27

6.4 fuel 28

6.5 lighting a ﬁ re 28

6.5.1 ﬂ ash ﬁ re 28

6.5.2 extended ﬁ re 29

6.6 smoking 29

6.7 optional fan operation 29

7.0 maintenance 30

7.1 ash removal procedures 30

7.1.1 ash removal with ash drawer 30

7.2 creosote formation and removal 31

7.3 runaway or chimney ﬁ re 31

7.4 chimney cleaning 31

7.5 door glass replacement 32

7.6 gasket replacement 32

7.7 care of glass 32

7.8 wood 33

8.0 replacement parts 34

8.1 overview 35

9.0 accessories 36

10.0 troubleshooting 37

11.0 warranty 38

12.0 notes 39

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd.

reserves the right to change or modify any information within this manual at any time without notice. Changes,

other than editorial, are denoted by a vertical line in the margin.

note:

EN

W415-1929 / A / 10.21.19

5

dimensions

O 6”

(152mm)

6 1/2”

(165mm)

31 1/2”

(800mm)

13”

(330mm)

21 5/8”

(549mm)

19 3/4”

(502mm)

26”

(660mm)

31 3/8”

(770mm)

O 6”

(152mm)

6 1/2”

(165mm)

13”

(330mm)

26”

(660mm)

25 1/4”

(641mm)

16 1/2”

(419mm)

9 1/4”

(235mm)

17”

(432mm)

19 3/4”

(502mm)

21 5/8”

(549mm)

16 1/2”

(419mm)

9 1/4”

(235mm)

22 1/4”

(565mm)

18 1/8”

(460mm)

1.0 general information

1.1 dimensions

TOP VIEW

FRONT VIEW

SIDE VIEW

LEG

MODEL

PEDESTAL

MODEL

W415-1929 / A / 10.21.19

EN

6

dimensions

• Before beginning your installation, consult with your local building code agency or ﬁ re ofﬁ cials and insurance

representative to ensure compliance.

• Non-toxic smoke will be emitted during the paint curing process, to help dissipate the smoke open a window

near the appliance.

• Remove any dust or debris off the top of the appliance before ﬁ ring the appliance as the paint will become

soft as the appliance heats up and will harden as the appliance cures. To cure the paint on your appliance

burn your appliance moderately hot during the ﬁ rst few ﬁ res.

• To keep the gasket from sticking to the appliance as the paint is curing, periodically open the door every 5-10

minutes.

• For the ﬁ rst two weeks use generous amounts of fuel and burn the appliance with the damper wide open for

an hour as the appliance goes through a process of eliminating moisture in the steel and ﬁ rebricks. The initial

heat output will be reduced while the moisture is being drawn from the appliance and it will be necessary

to build several hot ﬁ res to remove this moisture. DURING THIS PROCESS DO NOT OVERFIRE THE

APPLIANCE. REDUCE THE AMOUNT OF AIR COMING INTO THE APPLIANCE IF THE APPLIANCE

OR CHIMNEY BECOMES RED.

!

WARNING

• All wiring should be done by a qualiﬁ ed electrician and shall be in compliance with local codes. In the absence

of local codes, use the current CSA C22.1 Canadian Electric Code (in Canada) or the ANSI / NFPA N

o

70

National Electric Code in the United States.

• Burning your appliance with the ash well open or the ash door ajar creates a ﬁ re hazard and may cause

internal damage to the appliance or a house and/or chimney ﬁ re.

• Do not connect this appliance to a chimney ﬂ ue serving another appliance. Do not connect to any air

distribution duct or system.

• Provide adequate clearance for servicing and operating the appliance.

• Provide adequate ventilation.

• Never obstruct the front opening of the appliance.

• Objects placed in front of the appliance must be kept a minimum of 48” (121.9cm) from the front face of the

appliance.

• Do not install in a mobile home.

1.2 speciﬁ cations

Speciﬁ cations

Emissions 1.57 Grams/Hr

Efﬁ ciency 71.1%

Height pedestal model 31 3/8 (770mm)

Height leg model 31 1/2” (800mm)

Chamber (D.W.H)

11 5/8" x 20 7/8" x 11 5/8"

(295mm x 530mm x 295mm)

Viewing area 146.8 sq. in. (947.4 sq. cm)

Capacity 1.5 Cubic Feet (0.04 Cubic Meters)

Approx. Area Heated ** 600-1800 Square Feet (56-167m²)

Maximum Heat Output *** 52,000 BTU/Hr

Heat Output * 14,582 - 30,042

Duration Low Fire ** 6 Hours

Weight W/O Bricks 180 lbs (82kg)

Weight of Bricks 47 lbs (21kg)

Ideal Wood Length 16" (406mm)

Minimum Stack Height **** 15 feet (4.5m)

Efﬁ ciency Standard B415.1-10

* As tested using test method ALT-125.

** Figures will vary considerably with

individual conditions.

*** Wolf Steel Ltd. estimated realistic

BTU/hr with hardwood logs and regular

refueling.

**** Required in order to achieve proper

draft.

1.3 general instructions

EN

W415-1929 / A / 10.21.19

7

dimensions

This model was speciﬁ cally designed over many months of research to meet the 2020 U.S.A. EPA particulate emission

standards and has been extensively tested in Canadian laboratories. This system is the most efﬁ cient, simple and

trouble free we know and works as follows:

Secondary air from the rear hole travels up the back in the secondary air

housing to the manifold located at the top and shoots out laterally to oxidize the

gases below the smoke exit.

The lower combustion chamber is lined with high temperature ﬁ rebricks on 2

sides, the back and across the bottom, with a layer of ﬁ bre bafﬂ es at the top to

maintain a high temperature in the combustion chamber so that gases mixing

with the preheated air from the secondary air manifold tube are easily ignited

and burned. The appliance sides and back are shielded to direct the heat

upwards and forwards into the room.

Be sure to provide sufﬁ cient combustion air. There are many other appliances in

your home competing for air such as: a kitchen range hood, forced air heating

devices, clothes dryer or a bathroom exhaust fan.

After extended periods of non-operation such as following a vacation or a warm

weather season, the appliance may emit a slight odour for a few hours. This is

caused by dust particles on the ﬁ rebox burning off. Open a window to sufﬁ ciently ventilate the room.

If you experience smoking problems, you may been to open a door, a window or otherwise provide some method

of supplying combustion air to the appliance.

Do not use makeshift compromises during installation. Do not block or restrict air, grille, or louvre openings. Do

not add a hood. Burning your appliance with the door open or ajar creates a ﬁ re hazard that may result in a house

and/or chimney ﬁ re. All venting connections must be in compliance with the chimney manufacturer’s installation

instructions. Clearances referred to throughout this manual are the minimum requirements.

Your appliance must be installed in accordance with all national and local building code standards and the

standard of Chimney and Appliances, Vents and Solid Fuel

Burning Appliance NFPA #211. Consult the authority having

jurisdiction (such as municipal building department, ﬁ re

department, ﬁ re prevention bureau, etc.) to determine the

need to obtain a permit. If you are in doubt about the proper

installation for your situation, contact your dealer or local

building or ﬁ re ofﬁ cial. The manufacturer does not guarantee

that this appliance and its options will completely heat your

entire house.

Expansion / contraction noises during heating up and coolding down cycles are normal and to be expected.

It is recommended that in all cases, the appliance be secured to the ﬂ oor. Use the pallet packing brackets to

accomplish this.

1.4 general information

!

WARNING

• Do not operate this appliance without the legs or pedestal installed.

AIR INLET PATH

EXHAUST PATH

W415-1929 / A / 10.21.19

EN

8

dimensions

1.5 rating plate information

This illustration is for reference only. Refer

to the rating plate on the appliance for

accurate information

The rating plate must remain with the

appliance at all times. It must not be

removed.

note:

REPORT NO. /

NUMÉRO DE RAPPORT:

0415WS014E

UL1482 - 2011 / ULC S627 - 00

MODEL / MODÈLE: 2100

POUR INSTALLATION ET UTILISATION CONFORMÉMENT AUX INSTRUCTIONS DE WOLF

STEEL LTÉE. RENSEIGNEZ-VOUS AUPRÈS DES AUTORITÉS LOCALES DU BÂTIMENT

OU DU SERVICE DES INCENDIES AU SUJET DES RESTRICTIONS ET DES INSPECTIONS

D’INSTALLATION DANS VOTRE RÉGION.

HAUTEUR DE PLAFOND MINIMAL 7” (2,13M) EN UTILISANT UN TUYAU DE

RACCORDEMENT À PAROI SIMPLE.

BASE DE PROTECTION/PROTECTION DU PLANCHER COMBUSTIBLE: SI INSTALLÉ

SUR UN PLANCHER COMBUSTIBLE, L’APPAREIL DOIT ÊTRE PLACÉ SUR UNE PLAQUE

PROTECTRICE INCOMBUSTIBLE S’ÉTENDANT SUR 18” (455mm) (CANADA) / 16”

(406MM) (É.U.) À L’AVANT ET 8” (205MM) À L’ARRIÈRE ET SUR LES CÔTÉS.

TYPE DE CHEMINÉE: CHEMINÉE RÉSIDENTIELLE DE 6" DE DIAMÈTRE (152MM)

HOMOLOGUÉE (UL 103HT).

RACCORD DE CHEMINÉE: DIAMÈTRE DE 6” (152MM) D’ACIER DE CALIBRE 24

MINIMUM. 18” (455MM) DE DÉGAGEMENT MINIMAL ENTRE LE RACCORD HORIZONTAL

ET LE PLAFOND.

NE RIEN ENTREPOSER SOUS LE CHAUFFAGE.

DES MÉTHODES SPÉCIALES SONT REQUISES LORSQUE UNE CHEMINÉE TRAVERSE

UN MUR OU UN PLAFOND. VOIR LES INSTRUCTIONS ET LES CODES DU BÂTIMENT.

NE PAS RACCORDER À LA CHEMINÉE D’UN AUTRE APPAREIL.

COMBUSTIBLE: POUR USAGE AVEC LE BOIS SEULEMENT. N’UTILISEZ PAS DE

CHENET OU NE SURÉLEVEZ PAS LE BOIS. PRÉPAREZ LE FEU DIRECTEMENT SUR

L’ÂTRE.

AVERTISSEMENT: RISQUE D’ÉCHAPPEMENT DE FUMÉE. TENIR LA PORTE FERMÉE

LORSQUE LE POÊLE FONCTIONNE. REMPLACEZ LA VITRE PAR UNE VITRE EN

CÉRAMIQUE SEULEMENT.

NE SURCHAUFFEZ PAS L’APPAREIL. SI L’APPAREIL OU LES RACCORDS ROUGEOIENT,

L’APPAREIL SURCHAUFFÉE. INSPECTEZ ET NETTOYEZ LA CHEMINÉE FRÉQUEMMENT.

DANS CERTAINES CONDITIONS, DES DÉPÔTS DE CRÉOSOTE PEUVENT SE FORMER

RAPIDEMENT.

PATTES OPTIONNELLES : SI LES PATTES OPTIONNELLES SONT INSTALLÉES, ELLES

DOIVENT ÊTRE INSTALLÉES AVANT DE FAIRE FONCTIONNER L’APPAREIL.

SOUFFLERIE OPTIONNELLE: EP65M, 115V, 60HZ, 0,82A. TENEZ LE CORDON

ÉLECTRIQUE LOIN DE L’APPAREIL.

DANGER: RISQUE DE SECOUSSE ÉLECTRIQUE. DÉBRANCHEZ AVANT DE PROCÉDER

À L’ENTRETIEN.

INSTALL AND USE ONLY IN ACCORDANCE WITH WOLF STEEL LTD.’S

INSTRUCTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT

RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA.

MINIMUM CEILING HEIGHT: 7FT (2.13M) USING A SINGLE WALL

CONNECTOR.

HEARTH EXTENSION / COMBUSTIBLE FLOOR PROTECTION: IF

INSTALLED ON A COMBUSTIBLE FLOOR, UNIT MUST BE PLACED ON A

NON-COMBUSTIBLE FLOOR PROTECTOR EXTENDING 18” (455MM)

(CANADA) / 16” (406MM) (U.S.A.) IN FRONT AND 8” (205MM) TO THE SIDES AND

BACK.

CHIMNEY TYPE: MINIMUM 6” (152MM) DIAMETER LISTED (UL 103HT)

RESIDENTIAL CHIMNEY.

CHIMNEY CONNECTOR: 6” (152MM) DIAMETER MINIMUM 24 GAUGE

STEEL MINIMUM CLEARANCE FROM HORIZONTAL CONNECTOR AND

CEILING 18” (455MM).

DO NOT OBSTRUCT SPACE UNDER HEATER.

SPECIAL METHODS ARE REQUIRED WHEN PASSING A CHIMNEY

THROUGH A WALL OR CEILING. SEE INSTRUCTIONS AND BUILDING

CODES.

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER

APPLIANCE.

FUEL: FOR USE WITH SOLID WOOD FUEL ONLY. DO NOT USE GRATE OR

ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH.

WARNING: RISK OF SMOKE SPILLAGE. OPERATE ONLY WITH DOOR

FULLY CLOSED.

REPLACE GLASS ONLY WITH CERAMIC GLASS.

DO NOT OVERFIRE. IF HEATER OR CHIMNEY CONNECTORS GLOW, YOU

ARE OVERFIRING. INSPECT AND CLEAN CHIMNEY FREQUENTLY. UNDER

CERTAIN CONDITIONS OF USE CREOSOTE BUILD-UP MAY OCCUR RAPIDLY.

OPTIONAL LEGS: IF TO BE INSTALLED WITH OPTIONAL LEGS, LEGS

MUST BE INSTALLED PRIOR TO OPERATION.

OPTIONAL BLOWER KIT: EP65M, 115V, 60HZ, 0.82AMP. ROUTE CORD

AWAY FROM UNIT.

DANGER: RISK OF ELECTRICAL SHOCK. DISCONNECT POWER BEFORE

SERVICING UNIT.

LISTED SOLID FUEL BURNING SPACE HEATER /

POÊLE À COMBUSTIBLE SOLIDE HOMOLOGUÉ.

TESTED TO: / TESTÉ SELON:

SINGLE WALL CONNECTOR DOUBLE WALL CONNECTOR

Sidewall / mur de côté (A) 19" (48.3cm)

Sidewall to ﬂue / mur de côté à la buse (B) 28 7/8" (73.3cm)

Backwall / mur arrière (C) 17 1/2" (44.5cm) 12 1/2" (31.8cm)

Backwall to ﬂue / mur arrière à la buse (D) 21" (53.3cm) 16" (40.6cm)

Corner / coin (E) 11" (279mm) 7" (178mm)

Ceiling / plafond (F) 84" (213.4cm) 75" (190.5cm)

Clearances can be reduced with

shielding acceptable to local

authorities. Reduced installation

must comply with NFPA 211 or

CAN/CSA-B365. / Il est possible

de réduire les dégagements à

l’aide d’un protecteur conforme

aux normes des autorités locales.

Une installation réduite doit être

conforme aux normes NFPA 211

ou au CAN/CSA B365.

PARALLEL & CORNER /

PARALLÈLE & COIN

SINGLE WALL CONNECTEOR /

TUYAU DE RACCORDEMENT À

PAROI SIMPLE

DOUBLE WALL CONNECTEOR /

TUYAU DE RACCORDEMENT À

PAROI DOUBLE

B

A

C

F

D

E

BACK WALL /

MUR ARRIÈRE

BACK WALL /

MUR ARRIÈRE

ALCOVE / ALCÔVE

FLOOR

PROTECTION /

PROTECTION DU

PLANCHER

SIDE WALL /

MUR DE CÔTÉ

SIDE WALL /

MUR DE CÔTÉ

48” (1219.2mm)

MAX

KJ

F

G

K

J

I

L

M

N

ALCOVE / ALCÔVE

Ceiling / plafond (G) 75” (190.5cm)

MINIMUM FLOOR PROTECTION / PROTECTION MINIMAL DU PLANCHER

FRONT / DEVANT (L) SIDES / CÔTÉS (M) BACK / ARRIÈRE (N)

CANADA

USA / É-U

18” (45.7cm)

16” (40.6cm)

8” (203mm)

H

I

Sidewall / sur de côté (H)

Sidewall to ﬂue / mur de côté à la buse (I)

Backwall / mur arrière (J)

Backwall to ﬂue / mur arrière à la buse (K)

19" (48.3cm)

28 7/8" (73.3cm)

N/A 12 1/2" (31.8cm)

N/A 16" (40.6cm)

THIS WOOD HEATER NEEDS PERIODIC INSPECTION AND REPAIR FOR PROPER OPERATION. CONSULT THE OWNER’S MANUAL FOR FURTHER INFORMATION.

IT IS AGAINST FEDERAL REGULATIONS TO OPERATE THIS WOOD HEATER IN A MANNER INCONSISTENT WITH THE OPERATING INSTRUCTIONS IN THE

OWNER’S MANUAL. / CE POÊLE À BOIS DOIT ÊTRE INSPECTÉ ET RÉPARÉ PÉRIODIQUEMENT POUR UN FONCTIONNEMENT CORRECT. CONSULTEZ LE MANUEL

DU PROPRIÉTAIRE POUR PLUS D’INFORMATIONS. IL EST CONTRE LES RÈGLEMENTS FÉDÉRAUX POUR FAIRE FONCTIONNER CE POÊLE À BOIS D’UNE

MANIÈRE INCOMPATIBLE AVEC LES INSTRUCTIONS DE FONCTIONNEMENT DANS LE MANUEL DU PROPRIÉTAIRE.

N/A

W385-2373

2100

CAUTION:

ATTENTION:

HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN, CLOTHING AND

FURNITURE AWAY. CONTACT MAY CAUSE SKIN BURNS. SEE NAMEPLATE AND

INSTRUCTIONS.

WOLF STEEL LTD.

QUAND L’APPAREIL FONCTIONNE, LA SURFACE DEVIENT CHAUDE. NE PAS

TOUCHER. TENIR LES ENFANTS, LES VÊTEMENTS ET LES MEUBLES À L’ÉCART. LE

CONTACT PEUT CAUSER DES BRÛLURES À

LA PEAU. VOIR LA PLAQUE D’HOMOLOGATION ET LES INSTRUCTIONS.

24 NAPOLEON ROAD, BARRIE,

ON, L4M 0G8 CANADA

NAC GUANGZHOU P.R.C.

NO.69 HEFENG ROAD, GUANGZHOU,CHINA

MANUFACTURE DATE: / DATE DE FABRICATION:

YEAR/ANNÉE:

2019 2020

2021 2022

MONTH/MOIS:

2023 2024

243658710912111

U.S. ENVIRONMENTAL PROTECTION AGENCY Certiﬁed to comply with 2020

particulate emission standards using cordwood. Certiﬁé conforme à la norme

d’émanation de particles de 2020 en utilisant bois de corde.

40 CFR Part 60,

Subpart AAA

1.57 Grams Per Hour / 2020 Cordwood / 1,57 Grammes par heure

/ Bois de Corde 2020. Efﬁciency / Efﬁcacité: 71.1%

WOLF STEEL USA

103 MILLER DRIVE,

CRITTENDEN, KY,

401030 USA

SAMPLE

MENT AUX INSTRUCTIONS DEENT AUX INSTRUCTIONS

AUTORITÉS LOCALES DU BÂTIMENUTORITÉS LOCALES DU BÂTIM

DES RESTRICTIONS ET DES INSPECTIONES RESTRICTIONS ET DES INSPEC

13M) EN UTILISANT UN TUYAU DEN UTILISANT UN TUYAU DE

CTION DU PLANCHER COMBUSTIBLE: CHER COMBUSTI

S

I IN

S

TALL

É

TALLÉ

LE

TIBLE, L’APPAREIL DOIT ÊTRE PLACÉ SUR UNE PLAQUEÊTRE PLACÉ SUR UNE PLAQUE

TIBLE S’ÉTENDANT SUR 18” (455mm) (CANADA) / 16”455mm) (CANADA) / 16”

T ET 8” (205MM) À L’ARRIÈRE ET SUR LES CÔTÉS.ET 8” (205MM) À L’ARRIÈRE ET SUR LES CÔTÉS.

E:

CHEMINÉE RÉSIDENTIELLE DE 6" DE DIAMÈTRE (152MM) CHEMINÉE RÉSIDENTIELLE DE 6" DE DIAMÈTRE (152MM)

L

L 103HT).03HT).

CHEMINÉE:MINÉE:

DIAMÈTRE DE 6” (152MM) D’ACIER DE CALIBRE 2DIAMÈTRE DE 6” (152MM) D’ACIER DE CALIBRE

L

8” (455MM) DE DÉGAGEMENT MINIMAL ENTRE LE RACCORD HDE DÉGAGEMENT MINIMAL ENTRE LE RACCORD

AFOND.D.

N ENTREPOSER SOUS LE CHAUFFAGE.ENTREPOSER SOUS LE CHAUFFAGE

S MÉTHODES SPÉCIALES SONT REQUISES LORSQUE UNE CHEMÉTHODES SPÉCIALES SONT REQUISES LORSQUE UNE CH

UN MUR OU UN PLAFOND. VOIR LES INSTRUCTIONS ET LES CON MUR OU UN PLAFOND. VOIR LES INSTRUCTIONS ET LES C

NE PAS RACCORDER À LA CHEMINÉE D’UN AUTRE APPARENE PAS RACCORDER À LA CHEMINÉE D’UN AUTRE APPAR

CO

MBU

S

TIBLE

:COMBU

POUR USAGE AVEC LE BOIS SEULEMENUR USAGE AVEC LE BOIS SEULEME

P

CHENET OU NE SURÉLEVEZ PAS LE BOIS. PRÉPAREZ CHENET OU NE SURÉLEVEZ PAS LE BOIS. PRÉPAREZ

L’

Â

TRE.

L’ÂTRE.

A

VERTISSEMENT:

AVERTISSEMENT:

RISQUE D’ÉCHAPPEMENT DERISQUE

MP

LORSQUE LE POÊLE FONCTIONNE. REMPLACLORSQUE LE POÊLE FO

C

É

RAMIQUE SEULEMENT.

RAMIQUE SEULEM

NE SURCHAUFFEZ PAS L’APPAREIL. SI RCHAUFFEZ PA

L’APPAREIL SURCHAUFFÉE. INSPECTL’APPAREIL SURCHAUFF

DANS CERTAINES CONDITIONS, DDANS CERTAINES CONDITIO

RAPIDEMENT

.

RAPID

PATTES OPTIONNELLES :PATTES OPTIONNELLES

MP

DOIVENT ÊTRE INSTALLÉDOIVENT ÊTRE INSTALL

SOUFFLERIE OPTIONOUFFLERIE O

M

ÉLECTRIQUE LOIN CTRIQUE LOI

DANGER

:ER:

RISQU RISQ

M

À L’ENTRETIEÀ L’ENTRETI

SAM

ATE OR R

DOORDOOR

CTORS GLOW, YOUS GLOW, YOU

FREQUENTLY. UNDER NTLY. UNDER

P MAY

OCCUR RAPIDLY.

R RAPIDLY.

OPTIONAL LEGS, LEGS, LEGS

N..

60HZ, 0.82AMP. ROUTE CORD60HZ, 0.82AMP. ROUTE CORD

HOCK. DISCONNECT POWER BEFORECK. DISCONNECT POWER BEFORE

SA

A

SA

S

idewall / mur de côté

(

A

)dewall / mur de côté (A)

Sidewall to ﬂue / mur de côté à la buse Sidewall to ﬂue / mur de côté à la b

Backwall / mur arrière

(

C

)Backwall / mur arrière (C)

Backwall to ﬂue / mur arrière à Backwall to ﬂue / mur arrière à

Co

r

ner / coin

(

E

)coin (E)

Ceiling / plafond (Fg / plafond

SA

LEL & CORNER /

LLÈLE & COIN

LE W

AM

A

BB

A

AA

AM

M

AM

A

M

F

A

AM

A

E

AM

E

A

S

A

SA

A

SA

B

A

C

K WALL

/

ALL /

MUR ARRI

È

RE

ÈRE

S

IDE WALL

/

SIDE WALL /

MUR DE C

Ô

T

ÉMUR DE CÔTÉ

S

IDE WALL

/

SIDE WALL /

MU

R DE

CÔ

T

ÉMUR DE CÔTÉ

SAM

M

S

Ceiling / pCeiling / p

S

Sidew

Sid

S

IO

CONSUONSU

ÊLE À BOIS LE À BOIS

SAMPLE

EN

W415-1929 / A / 10.21.19

9

installation planning

2.0 installation planning

2.1 appliance placement

BACK WALL

B

SIDE WALL

A

BACK WALL

C

SIDE WALL

F

D

E

PARALLEL & CORNER SINGLE WALL CONNECTOR DOUBLE WALL CONNECTOR

Sidewall (A) 19" (48.3cm)

Sidewall to ﬂ ue (B) 28 7/8" (73.3cm)

Backwall (C) 17 1/2" (44.5cm) 12 1/2" (31.8cm)

Backwall to ﬂ ue (D) 21" (53.3cm) 16" (40.6cm)

Corner (E) 11" (279mm) 7" (178mm)

Ceiling (F) 84" (213.4cm) 75" (190.5cm)

Clearances can be reduced with shielding acceptable to local authorities. Reduced installation must comply with

NFPA 211 or CAN/CSA-B365.

2.2 minimum clearance to combustibles

!

WARNING

• Do not install into any area having less than 7 feet (2.1m) (ceiling to appliance bottom, excluding hearth

height).

We recommend having your Timberwolf wood burning appliance installed by a qualiﬁ ed technician. However,

should you choose to install the appliance yourself, it is extremely important that you follow all installation

instructions for the appliance, the chimney and connector if applicable, as well as local building codes. At the very

least, draw a detailed plan of your installation, including clearance dimensions to combustibles, and have your

authorized dealer review them to conﬁ rm that they conform to the relative installation parameters.

When positioning the appliance, it may be necessary to adjust its position to prevent the chimney/vent system

from intersecting with a framing member and to meet the minimum combustible clearance requirements. Its

location should also avoid the potential for drapes or doors to swing within 48” (122cm) in front of the appliance

to prevent a ﬁ re hazard.

note:

W415-1929 / A / 10.21.19

EN

10

installation planning

2.3 alcove installation

If the appliance is to be installed on top of a combustible ﬂ oor, it must be placed on an approved non-combustible

hearth pad, that extends 8" (203mm) beyond the appliance sides and back and 18" (457mm) in Canada /

16” (406mm) in the USA to the front. The reduced clearance from the back of the appliance may result in the

appliance pad terminating shorter than 8" (203mm) beyond the appliance.

Refer to local building codes for suitable ﬂ oor protection materials.

K

J

I

MINIMUM FLOOR PROTECTION

FRONT (L) SIDES (M) BACK (N)

CANADA 18" (45.7cm) 8" (203mm)

USA 16" (406mm) 8" (203mm)

2.4 ﬂ oor protection

The following are signs that fresh air may be required:

• When there is combustion present: Wood burns poorly, smoke spills, back-draft takes place and your

chimney does not draw steadily.

• In the winter there is too much condensation on the windows.

• Opening a window seems to alleviate the above symptoms.

• A ventilation system is installed in the house.

• Other devices are present that exhaust house air.

• The house has tight ﬁ tting windows and/or is equipped with a well-sealed vapour barrier.

Systems such as HRV’s are designed to bring fresh air into your home and will resolve these related performance

issues with your appliance.

Floor protection is required for spark and ash shielding, but not for limiting ﬂ oor temperatures from the radiant

heat of the appliance. The appliance was designed and safety-tested so that without any protection, the ﬂ oor

would not overheat.

note:

If a section of horizontal chimney connector is used, ﬂ oor protection is required under

the chimney connector and 2” (51mm) beyond each side.

note:

L

M

N

M

ALCOVE

PARALLEL & CORNER SINGLE WALL CONNECTOR DOUBLE WALL CONNECTOR

Ceiling (G)

N/A

75" (190.5cm)

Side wall (H) 19” (48.3cm)

Sidewall to ﬂ ue (I) 28 7/8” (73.3cm)

Backwall (J) 12 1/2” (31.8cm)

Backwall to ﬂ ue (K) 16” (40.6cm)

19"

(48.3cm)

28

7

/

8

"

(733.4mm)

ALCOVE

48” (122cm)

MAX

AB

Your appliance may be installed using a listed

double wall connector, such as Security DL6 in

Canada, the Simpson Duravent Plus DVL in the

USA or an equivalent double wall connector,

into an alcove having a depth of no more than 4

feet and a height of at least 6’3". The minimum

clearances are as shown.

F

2.5 outside air

G

I

H

J

K

EN

W415-1929 / A / 10.21.19

11

installation

3.0 installation

!

WARNING

• Wear gloves, protective footwear and safety glasses for protection.

• Carefully follow the instructions for assembly of the pipe and other parts needed to install the appliance.

Failure to do so may result in a ﬁ re, especially if combustibles are too close to the appliance or chimney and air

spacers are blocked, preventing the free movement of cooling air.

• Do not draw outside air from garage spaces. Exhaust products of gasoline engines are hazardous. Do not

install outside air ducts such that the air may be drawn from attic spaces, basements or above the rooﬁ ng

where other heating appliances or fans and chimneys exhaust or utilize air. These precautions will reduce the

possibility of appliance smoking or air ﬂ ow reversal. The outside air inlet must remain clear of leaves, debris, ice

and/or snow. It must be unrestricted while appliance is in use to prevent room air starvation which can cause

smoke spillage and an inability to maintain a ﬁ re. Smoke spillage can also set off smoke alarms.

• Negative pressure within your home may inadvertently affect your appliance.

• To prevent contact with sagging or loose insulation, the appliance must not be installed against vapour barriers

or exposed insulation. Localized overheating could occur and a ﬁ re could result.

• Do not use makeshift compromises during installation. Do not block or restrict air, grille or louvre openings. Do

not add a hood.

• To prevent personal injury, keep hand tools in good condition, sharpen cutting edges and make sure tool

handles are secure.

• Always maintain the minimum air space required in the enclosure to prevent ﬁ res.

• Check with local building ofﬁ cials for any permits required for installation of this appliance and notify your

insurance company prior to proceeding.

3.1 chimney

Your appliance may be connected to a factory built or masonry chimney. If you are using a factory built chimney,

it must comply with ULCS629 (Canada) or UL103 (USA) standards. It must therefore be a 6" (152mm) HT Type

(2100°F) chimney. It is extremely important that it be installed according to the manufacturer’s speciﬁ cations.

The manufacturer’s installation instructions and speciﬁ ed clearances should always be followed in accordance with

local and national codes. In Canada the CSA B365 and the CSA C22.1 installation codes are to be followed. In

the USA the ANSI NFPA 70 and ANSI NFPA 211 installation codes are to be followed.

Chimney and chimney connector must be in good condition and kept clean.

!

WARNING

• Never install a single wall slip section or smoke pipe in a chase structure. The higher temperature of this

single wall pipe may radiate sufﬁ cient heat to combustible chase materials to cause a ﬁ re.

• Do not connect this appliance to a chimney system serving another appliance.

• To avoid danger of ﬁ re, all instructions must be strictly followed, including the provision of air space

clearance between chimney system and enclosure. To protect against the effects of corrosion on those

parts exposed to the weather, we recommend that the chase top be painted with a rust-resistant paint.

• Do not ﬁ ll any framed space around the chimney with insulation or any other material. Insulation placed in

this area could cause adjacent combustibles to overheat.

• Maintain a minimum 2” (51mm) air clearance to all parts of the chimney system at all times (this excludes the

chimney connection). Failure to maintain this 2” (51mm) air clearance will cause a structure ﬁ re. Never ﬁ ll this

space with any type of material.

• Detailed instructions for installation of the chase top, storm collar and termination cap are packaged with

these parts.

• Do not cut rafters or ceiling joists without ﬁ rst consulting a building ofﬁ cial to ensure structural integrity is not

compromised.

• Firestop spacers must be used whenever the chimney penetrates a ceiling/ﬂ oor area.

• The total horizontal vent length should not exceed 40% of the chimney height above the appliance all

horizontal smoke pipe must slope slightly upwards a minimum of 1/4” (6.4mm) per foot and all connections

must be tight and secured by three sheet metal screws equally spaced. An uninsulated smoke pipe shall

not pass through an attic, roof space, closet or similar concealed space, or through a ﬂ oor, ceiling, wall or

partition, or any combustible constructions.

• Do not use any makeshift materials during installation.

W415-1929 / A / 10.21.19

EN

12

installation

3.1.1 chimney connection

Your chimney connector and chimney must have the same diameter as the appliance’s exhaust ﬂ ue outlet. The

appliance pipe must be made of aluminized or cold roll steel with a minimum 24 gauge (0.6mm) thickness. It is

strictly forbidden to use galvanized steel.

A 6” (152.4mm) diameter single or double wall chimney connector, used to connect the appliance to the chimney,

must be installed with the crimped end toward the appliance. This will ensure that the moisture which condenses

from the burning wood will ﬂ ow back into the ﬁ re chamber. Each joint in the chimney connector must be secured

with at least three sheet metal screws, equally spaced around the circumference.

For installation of your chimney connector, the following recommendations may be useful.

• The chimney connector must be short and straight. For optimum performance, it is recommended that all

horizontal runs have a minimum 1/4” (6.4mm) rise per foot (0.3m), with the higher end of the section toward

the chimney. For safe and proper operation of the appliance, see “INSTALLATION” instructions.

• To ensure a good draft, the total horizontal length of the connector should never exceed 8’ (2.4m) to 10’

(3.1m). In the case of vertical installation, the total length of the connector can be longer and connected

without problem to the chimney at the ceiling level.

• There should never be more than two 90° elbows in the entire connector and chimney system. Never start

with a 90° elbow. Always go up vertically for at least 2 feet (0.6m) from the flue collar before using a 90°

elbow.

• The connector must not pass through any combustible material, nor may it pass through a concealed

space (such as an attic, roof space, or closet). If passing through a wall, ceiling or into a masonry chimney,

use either chimney components listed for that speciﬁ c use, or means acceptable to local authorities having

jurisdiction over the installation.

This appliance must be connected to:

A. A chimney complying with the requirements for Type HT

chimneys in the Standard for Chimneys, Factory-Built,

Residential Type and Building Heating Appliance, or

B. A code-approved masonry chimney with a ﬂ ue liner. Vent the

stove into a masonry chimney or an approved, insulated solid-

fuel stainless-steel chimney with as short and straight a length

of 6” (152.4mm) diameter chimney connector as possible.

Connection to a masonry thimble cemented in place.

TOWARD

APPLIANCE

FLUE GAS

DIRECTION

MALE END OF

CONNECTOR

OR CHIMNEY

PIPE

EN

W415-1929 / A / 10.21.19

13

installation

3.1.2 adding sections

An insulated stainless steel

chimney must be supported

at the ceiling or roof and its

installation must comply with

its manufacturer’s instructions.

Add chimney sections, according to the manufacturers installation instructions. If the chimney system passes

through an attic space a rafter radiation shield or attic insulation shield is required. The chimney must extend at

least 3ft (0.9m) above its point of contact with the roof and at least 2ft (0.6m) higher than any wall, roof or building

within 10ft (3.1m). If the chimney extends more than 5ft (1.5m) above the roof, it must be secured using a roof

brace or guide wires. A raincap must be installed to avoid internal damage and corrosion.

3 FT (1m)

MIN

3 FT (1m)

MIN

10 FT (3m)

OR MORE

FLAT ROOF

WALL

RIDGE

LESS THAN

10FT (3m)

2 FT (0.6m) MIN

3 FT (1m)

MIN

2 FT (0.6m)

MIN

LESS THAN

10FT (3m)

3 FT (1m)

MIN

2 FT (0.6m)

MIN

10 FT (3m)

TO NEAREST

ROOFLINE

2 ft

MIN.

10 ft

3 ft

MIN.

ROOF RADIATION

PLATE

ATTIC

RADIATION

SHIELD (AFRS)

2" MIN.

FIRESTOP

(FS+)

ENCLOSURE

2" MIN.

FINISHING SUPPORT

(BS2 OR FCSC) **

7 1/2"

MIN.

BASE TEE

* 18"

MINIMUM

* 18"

MINIMUM

* CLEARANCE CAN BE REDUCED IF A LISTED CHIMNEY

CONNECTOR IS USED.

** CLEARANCES CAN BE LESS THAN 2" WHERE

ESTABLISHED BY THE SUPPORT.

This illustration is for wood

appliances only.

note:

W415-1929 / A / 10.21.19

EN

14

installation

3.1.3 typical through the ceiling

A. Move the stove into position with the ﬂue centered, midpoint between two

joists to prevent having to cut them. Use a plumb bob to line up the center.

B. Cut and frame an opening in the ceiling to provide a 2” (50.8mm)

clearance between the outside of the chimney and any combustible

material. Do not ﬁll this space with any type of material.

Nail headers between the joist for extra support.

Firestop spacers must be placed on the bottom

of each framed opening in any ﬂoor or ceiling

that the chimney passes through. If your

chimney system is enclosed within the attic

area, a rafter radiation shield is required.

C. Hold a plumb bob from the underside of the

roof to determine where the opening in the

roof should be. Cut and frame the roof opening

to maintain proper 2” (50.8mm) clearances.

HEADERS

FIRESTOP SPACER -

UNDERSIDE OF JOIST

FLOOR

PROTECTOR

ROOF

FLASHING

STORM

COLLAR

TERMINAL

COMBUSTIBLE

WALL

MAINTAIN

2” (50.8mm)

CLEARANCE

CHIMNEY

CONNECTOR

CEILING

SUPPORT

LISTED CHIMNEY

INSULATION

CEILING

SUPPORT

LISTED

CHIMNEY

SPECIFIED

CLEARANCE

TO STOVE

note:

The chimney must be supported at the ceiling or

roof so that its weight does not rest on the appliance

and must comply with its manufacturer’s instructions.

EN

W415-1929 / A / 10.21.19

15

installation

3.1.4 typical through the wall

If possible, design the installation so that the connector does not pass through a combustible wall. If during

your installation you must pass through a combustible wall, check with your building inspector before you

begin. Also check with the chimney connector manufacturer for any speciﬁc requirements.

Consult with your dealer regarding special connection components available for use for wall pass-throughs.

Use only parts that have been tested and listed for use in a wall pass-through.

FLOOR

PROTECTOR

ROOF

FLASHING

STORM

COLLAR

TERMINAL

COMBUSTIBLE

WALL

MAINTAIN 2”

(50.8mm) CLEARANCE

THROUGH EAVE

COMBUSTIBLE

CEILING

LISTED

CHIMNEY

COMBUSTIBLE

OUTSIDE WALL

TO

STOVE

2” (50.8mm)

CLEARANCE

INSULATED

“T”

WALL

SUPPORT

WALL SPACER

FOR OUTSIDE

WALL

SECTION

LISTED

CHIMNEY PIPE

THIMBLE

CHIMNEY

CONNECTOR

W415-1929 / A / 10.21.19

EN

16

installation

3.1.5 typical existing masonry

You can also install your appliance using your

existing masonry chimney. To do so, use the

following guidelines. Use a factory-built thimble, or

construct your own brick thimble. If you are using a

masonry chimney, it is important that it be built in

compliance with the speciﬁcations of the Building

Code in your region. It must normally be lined with

ﬁre clay bricks, metal or clay tiles sealed together

with ﬁre cement. (Round ﬂues are the most

efﬁcient). The maximum ﬂue size is 8” (203.2mm) x

8” (203.2mm) square or 6” (152.4mm) round. For

greater diameters it is necessary to install a 6”

(152.4mm) stainless steel liner.

FLOOR

PROTECTOR

CHIMNEY

CONNECTOR

COMBUSTIBLE

WALL

CLEARANCE

EAVE

RAFTER

CLEARANCE WITH FIRESTOP

CEILING JOIST

THIMBLE

EN

W415-1929 / A / 10.21.19

17

4.0 ﬁ nishing

4.1 leg installation

!

WARNING

• Do not remove knockout unless installing the optional ash drawer kit.

To avoid being damaged during shipping, the appliance has been bolted to the pallet and must be unbolted before

the appliance can be installed.

A. With the bolt through the legs, feed the washer and lock washer onto the bolt. Thread the nut a thread or

two onto the bolt and slide the leg onto the slot on appliance (Fig. 4-1).

B. Slide the heat shield over the four bolts. Finally, secure the heat shield in place using the remaining nuts

(Fig. 4-2).

C. Lift the appliance up and gently set down on all four legs. Do not pivot appliance up on its legs, as this

could result in damage to the legs.

D. Place logo as illustrated (Fig. 4-3). For additional logo placement locations, see “optional ash drawer”

section.

LOGO

PLACEMENT

KNOCKOUT

(SEE WARNING

ABOVE)

If installing the optional ash drawer, see “optional ash drawer kit (EP20LAD)” section prior to heat shield and leg

installation. Legs may need to be adjusted in order to properly align with the heat shield holes.

note:

Bolts must be tight prior to heat shield installation.

note:

Fig. 4-1

Fig. 4-2

Fig. 4-3

W415-1929 / A / 10.21.19

EN

18

ﬁ nishing

1. Pivot the door open and lift the door and pins off the bushings.

2. Set the door aside being careful not to scratch the paint.

PINS

BUSHINGS

To avoid being damaged during shipping, the appliance

has been bolted to the pallet and must be unbolted

before the appliance can be installed.

A. Using the machine screws supplied, secure the

pedestal to the four brackets on the bottom of

the ﬁ rebox.

B. Lift the appliance up and gently set down on

pedestal. Do not pivot appliance up as it could

result in damage to the pedestal.

PEDESTAL

LOGO PLACEMENT

4.2 pedestal installation

4.3 door removal

!

WARNING

• Burning your appliance in with the doors open or ajar creates a ﬁ re hazard that may result in a house and/or

chimney ﬁ re.

• Do not strike or slam door.

• Never remove the door when the appliance is hot.

If an optional ash drawer kit is to be installed, ensure

open side of pedestal is at the front of the appliance.

If not, opening should be at the back.

note:

EN

W415-1929 / A / 10.21.19

19

ﬁ nishing

4.4 door handle installation

1. Twist the large wire handle over the end of the handle rod.

2. Twist the smaller wire handle over the end of the air damper rod below the door.

DOOR

HANDLE

DOOR HANDLE

LATCH

LOCK

NUT

DOOR

SPACER

FRONT VIEW

NOTE: Position of

door handle latch.

NOTE: DOOR MAY NOT BE AS

ILLUSTRATED

SPRING

WASHER

!

WARNING

• Burning your appliance in with the doors open or ajar creates a ﬁ re hazard that may result in a house and/or

chimney ﬁ re.

• Do not strike or slam door.

• Never remove the door when the appliance is hot.

W415-1929 / A / 10.21.19

EN

20

ﬁ nishing

4.5 secondary air tubes

2

COTTER

TUBE

RETAINER

1

HOLE

1. Start at the back working forwards by sliding the secondary air tube in the ﬁ rebox and inserting the tube

into the hole, as illustrated in “1”.

2. Slide the tube into the opposite hole. With the holes on the secondary air tube pointing forward, align the

tube with the tube retainer and insert the cotter pin,

as illustrated in “2”.

3. Spread the cotter pin to retain.

La page est en cours de chargement...

Continental Fireplaces 2100-1 Le manuel du propriétaire

Continental Fireplaces 2100-1 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents