NAPOLEON EPI22 Manuel utilisateur

Catégorie
Poêles
Taper
Manuel utilisateur
EN
FR
PG
33
W415-1466 / B / 08.20.18
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.
This wood appliance needs periodic inspection and repair for proper operation. It is against United
States federal regulations to operate this wood appliance in a manner inconsistent with operating
instructions in this manual.
INSTALLATION AND
OPERATING INSTRUCTIONS
1.14G
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone 1 (866) 820-8686 • www.timberwolffi replaces.com • ask@timberwolffi replaces.com
SAFETY INFORMATION
!
WARNING
If the information in these instructions is not followed exactly,
a re or explosion may result causing property damage,
personal injury or death. Improper installation, adjustment,
alteration, service or maintenance can cause injury or property
damage, bodily injury or even death. Please read entire
manual before you install and use your appliance.
- This appliance can be very hot when burning.
- Combustible materials such as  rewood, wet clothing, etc. placed too
close can catch  re.
- Children and pets must be kept from touching the appliance when it is hot.
- The chimney must be sound and free of cracks. Before installing this unit,
contact the local building or  re authority and follow their guidelines.
- Operate only with the door tightly closed.
- Burn wood behind the log retainer directly on the  rebricks.
- Do not use an elevated grate or otherwise raise the  re.
- At least 14 square inches (90 square centimeters) of outside air must be
admitted to the room or directly to the unit through a 4” (102mm) diameter
pipe.
- This appliance is designed to burn natural wood only. Higher ef ciencies
and lower emissions generally result when burning air dried seasoned
hardwoods, as compared to softwoods or to green or freshly cut
hardwoods.
- Do not start a  re with chemicals or  uids such as gasoline, engine oil, etc.
- Do not burn trash or garbage, lawn clippings / waste, rubber, waste
petroleum products, paints or paint thinners / solvents, plastic, materials
containing asbestos, construction debris, railroad ties or treated wood,
manure or animal remains, salt water driftwood or salted materials,
unseasoned wood, coal, charcoal, coloured paper, cardboard, plywood or
particleboard.
- Do not let the appliance become hot enough for any part to glow red.
- KEEP THE STOVE TOP TEMPERATURE BELOW 700°F (371°C). Attempts to
achieve heat output rates that exceed design speci cations can result in
steel distortion and damage.
$10.00
LA VITRE CHAUDE CAUSERA
DES BRÛLURES.
NE PAS TOUCHER LA VITRE
AVANT QU’ELLE AIT REFROIDI.
NE JAMAIS LAISSER LES
ENFANTS TOUCHER LA VITRE.
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
!
WARNING
!
AVERTISSEMENT
FOR INDOOR USE ONLY!
MODEL EPI22 MEETS THE 2015 U.S ENVIRONMENTAL PROTECTION AGENCY (E.P.A.) CRIB WOOD EMISSION LIMITS FOR WOOD STOVES SOLD AFTER MAY
15, 2015, 40 C.F. R. PART 60. THESE APPLIANCES HAVE BEEN TESTED AND LISTED BY OMNI-TEST LABORATORIES, INC. TO STANDARDS: ULC-S628, UL1482.
EPI22
WOOD INSERT
W415-1466 / B
/ 08.20.18
EN
2
NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.
TABLE OF CONTENTS
1.0 INSTALLATION OVERVIEW 3
2.0 INTRODUCTION 4
2.1 DIMENSIONS (COMPLETE WITH FLASHING) 5
2.2 SPECIFICATIONS 5
2.3 GENERAL INSTRUCTIONS 5
2.4 GENERAL INFORMATION 6
2.5 E.P.A. COMPLIANCE 7
2.6 RATING PLATE LOCATION 8
3.0 PRE-INSTALLATION PREPARATION 9
3.1 MINIMUM CLEARANCE TO COMBUSTIBLES 9
4.0 INSTALLATION 10
4.1 TYPICAL EXISTING MASONRY 11
4.2 FACTORY BUILT FIREPLACE 12
5.0 FINISHING 13
5.1 SECONDARY AIR TUBES 13
5.2 DOOR INSTALLATION 14
5.3 DOOR HANDLE INSTALLATION 14
5.4 BRICKS AND BAFFLES INSTALLATION 15
5.5 FLASHING INSTALLATION 16
5.6 BLOWER INSTALLATION 17
6.0 OPERATION 18
6.1 OPTIMUM BURN METHOD 19
6.2 AIR CONTROL 20
6.3 FIRE EXTINGUISHERS / SMOKE DETECTORS 20
6.4 FUEL 20
6.5 LIGHTING A FIRE 21
6.5.1 FLASH FIRE 21
6.5.2 EXTENDED FIRE 21
6.6 SMOKING 21
7.0 MAINTENANCE 22
7.1 ASH REMOVAL PROCEDURES 22
7.2 CREOSOTE FORMATION AND REMOVAL 22
7.3 RUNAWAY OR CHIMNEY FIRE 23
7.4 CHIMNEY CLEANING 23
7.5 DOOR REMOVAL 24
7.6 GLASS REPLACEMENT 24
7.7 CARE OF GLASS 25
7.8 CARE OF PLATED PARTS 25
7.9 BLOWER SERVICE OR REPLACEMENT 25
7.10 GASKET AND SHIELD REPLACEMENT 26
7.11 WOOD 27
8.0 REPLACEMENTS 28
9.0 TROUBLESHOOTING 30
10.0 WARRANTY 31
W415-1466 / B / 08.20.18
EN
3
1.0 INSTALLATION OVERVIEW
Rating plate, see
“RATING PLATE
INFORMATION”
section.
Blower, see “BLOWER INSTALLATION”
section.
Door, see “DOOR
AND HANDLE
INSTALLATION”
section.
Flashing, see “FLASHING
INSTALLATION” section.
Draft, see “AIR
CONTROL” section.
W415-1466 / B
/ 08.20.18
EN
4
2.0 INTRODUCTION
3.17G
!
WARNING
THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.
ANY CHANGES OR ALTERATIONS TO THIS APPLIANCE OR ITS CONTROLS CAN BE DANGEROUS AND
IS PROHIBITED.
Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance
according to operating instructions could cause fi re or injury.
Before installing this appliance, contact the local building or fi re authority and follow their guidelines.
This appliance must be installed by a qualifi ed installer.
Risk of burns. The appliance should be turned off and cooled before servicing.
Do not operate without fully assembling all components.
Do not let the appliance become hot enough for any part to glow red.
Do not install damaged, incomplete or substitute components.
Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges may
be sharp.
Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid
burns or clothing ignition.
Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young
children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there
are at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to
keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.
Clothing or other fl ammable material should not be placed on or near the appliance. Objects placed in front of the
appliance must be kept a minimum of 4 feet (1.2m) away from the front face of the appliance.
Due to high temperatures, the appliance should be located out of traffi c and away from furniture and draperies.
Ensure you have incorporated adequate safety measures to protect infants/toddlers from touching hot surfaces.
Even after the appliance is out, the glass and / or screen will remain hot for an extended period of time.
Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot
surfaces. These screens and guards must be fastened to the fl oor.
Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
Under no circumstances should this appliance be modifi ed.
This appliance must not be connected to a chimney fl ue pipe servicing a separate solid fuel burning appliance.
Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should
be done by a licensed or qualifi ed service person.
Do not strike or slam shut the appliance glass door.
Only doors / optional fronts certifi ed with the appliance are to be installed on the appliance.
Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all
plastic bags, these are not toys and should be kept away from children and infants.
If the appliance is not properly installed, a house fi re may result. Do not expose the appliance to the elements (ex.
rain, etc.) and keep the appliance dry at all times. Wet insulation will produce an odour when the appliance is used.
The chimney must be sound and free of cracks. Clean your chimney a minimum of twice a year and as required.
Do not start a fi re with chemicals or fl uids such as gasoline, engine oil, etc.
Your appliance requires periodic maintenance and cleaning. Failure to maintain your appliance may lead to smoke
spillage in your home.
Lower emissions generally result when burning air dried seasoned hardwoods, as compared to softwoods or too
green or freshly cut hardwoods. Burning wet unseasoned wood can cause excessive creosote accumulation.
When this is ignited it can cause a chimney fi re that may result in a serious house fi re.
This appliance is designed to burn natural wood only. Do not burn trash or garbage, lawn clippings / waste,
rubber, waste petroleum products, paints or paint thinners / solvents, plastic, materials containing asbestos,
construction debris, railroad ties or treated wood, manure or animal remains, salt water driftwood or salted
materials, unseasoned wood, coal, charcoal, coloured paper, gift wrapping, cardboard, plywood or particleboard.
Burning these materials may result in release of toxic fumes or render the appliance ineffective and cause smoke.
Burn wood directly on the fi rebricks. Do not elevate grate or otherwise raise the fi re.
Do not store wood within appliance installation clearances or within the space required for re-fueling and ash removal.
Ashes must be disposed in a metal container with a tight lid and placed on a non-combustible surface well away
from the home or structure until completely cool.
Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.
Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to
decorations, a T.V. or other electronic components.
If equipped, the catalyst must be installed and in good working order. It is recommended that the catalyst is
inspected at least 3 times per heating season.
W415-1466 / B / 08.20.18
EN
5
* As tested using the test method 28.
** Figures will vary considerably with individual conditions.
*** Wolf Steel Ltd. estimated realistic BTU/hr with hardwood logs and regular refueling.
Specications EPI22
CHAMBER (D.W.H) 14 5/8" (371mm) x 20 7/8" (530mm) x 11 5/8" (295mm)
CAPACITY 1.9 ft
3
(0.05m
3
)
APPROX. AREA HEATED** 800-1800 ft
2
(74m
2
-167m
2
)
MAXIMUM HEAT OUTPUT *** 65,000 BTU/Hr
HEAT OUTPUT* 12,084 -36,976 BTU/Hr
DURATION LOW FIRE* 8 Hours
WEIGHT w/o BRICKS 225 lbs (102kg)
WEIGHT OF BRICKS 60 lbs (27kg)
A B
MIN DEPTH 4" (102mm) 14" (356mm)
MAX DEPTH 7 1/2" (191mm) 17 1/2" (445mm)
2.1 DIMENSIONS (COMPLETE WITH FLASHING)
2.2 SPECIFICATIONS
31"
787mm
20"
508mm
43"
1092mm
21 3/4"
522mm
10 1/2"
267mm
14"
356mm
17 1/2"
445mm
4"
102mm
7 1/2"
191mm
25 3/8"
645mm
FRONT VIEW SIDE VIEW TOP VIEW
A
B
2.3 GENERAL INSTRUCTIONS
4.7
ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE WITH
LOCAL CODES. IN THE ABSENCE OF LOCAL CODES, USE THE CURRENT CSA22.1 CANADIAN
ELECTRIC CODE IN CANADA OR THE CURRENT NATIONAL ELECTRIC CODE ANSI/NFPA NO. 70 IN
THE UNITED STATES.
THIS APPLIANCE HAS NOT BEEN TESTED WITH ANY VENTED OR UNVENTED GAS LOG SET. TO
REDUCE RISK OF FIRE OR PREVENT INJURY, DO NOT INSTALL A VENTED OR UNVENTED GAS LOG
SET INTO THE APPLIANCE.
BURNING YOUR UNIT WITH THE ASH DUMP DOOR OPEN OR AJAR CREATES A FIRE HAZARD THAT
MAY RESULT IN DISCOLOURATION TO THE GOLD PLATED DOOR, INTERNAL DAMAGE TO THE
APPLIANCE OR A HOUSE CHIMNEY FIRE.
DO NOT CONNECT THIS APPLIANCE TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
THIS APPLIANCE AND IT’S COMPONENTS ARE DESIGNED TO BE INSTALLED AND OPERATED AS A
SYSTEM. ANY ALTERATION TO OR SUBSTITUTION FOR ITEMS IN THIS SYSTEM, UNLESS ALLOWED
BY THESE INSTALLATION INSTRUCTIONS, WILL VOID THE LISTING AND MAY VOID THE PRODUCT
WARRANTY. IT MAY ALSO CREATE A HAZARDOUS INSTALLATION. READ THROUGH THESE
INSTRUCTIONS THOROUGHLY BEFORE STARTING YOUR INSTALLATION AND FOLLOW THEM
CAREFULLY THROUGHOUT YOUR PROJECT.
!
WARNING
* A and B are adjustable in 3/8" (9.5mm) increments (see min max below).
[552mm]
W415-1466 / B
/ 08.20.18
EN
6
2.4 GENERAL INFORMATION
Before beginning your installation, consult with your local building code agency or re ofcials and
insurance representative to ensure compliance.
Non-toxic smoke will be emitted during the paint curing process, to help dissipate the smoke open a
window near the appliance.
Remove any dust or debris off the top of the appliance before ring the appliance as the paint will
become soft as the appliance heats up and will harden as the appliance cures. To cure the paint on
your appliance burn your appliance moderately hot during the rst few res.
To keep the gasket from sticking to the appliance as the paint is curing, periodically open the door
every 5-10 minutes.
For the rst two weeks use generous amounts of fuel and burn the appliance with the damper wide
open for an hour as the appliance goes through a process of eliminating moisture in the steel and
rebricks. The initial heat output will be reduced while the moisture is bring drawn from the appliance
and it will be necessary to build several hot res to remove this moisture. DURING THIS PROCESS
DO NOT OVERFIRE THE APPLIANCE. REDUCE THE AMOUNT OF AIR COMING INTO THE
APPLIANCE IF THE APPLIANCE OR CHIMNEY BECOMES RED.
Your appliance was specically designed to meet the 2015 U.S.A. EPA particulate emission standards and
have been extensively tested in Canadian and American laboratories. This system is the most efcient, simple
and trouble free we know and works as follows:
Your appliance is the exact duplication of the clean-burning technology found in all Timberwolf® EPA certied
freestanding stoves. External modications have been made to allow its installation as a “functional insert” with a heat
circulating blower system and a means of enclosing the solid fuel burning replace cavity for greater heating efciency.
Your appliance must be installed only into a solid fuel burning replace that is at least 14” (356mm) deep 25 7/8”
(657mm) wide and 22” (559mm) high with an approved lined chimney at least 15 feet high (4.6m) and a hearth of 18”
(457mm). This minimum recess can only be achieved if the opening height is sufcient enough to allow the connector
to t under the noncombustible facing. The appliance and chimney must be constructed in accordance with all national
and local building code standards.
The chimney vent system used on your wood burning appliance should be designed with the least amount of
restriction possible to enable the exhaust products to easily ow through it. Chimney vent systems that are too
short or too long can also have an adverse affect on the ow of exhaust through it. The wood burning appliance
and chimney vent system also require a sufcient supply of combustion air not only to support the combustion in the
combustion chamber but to replace the exhaust leaving it so it can ow freely
up through the vent system and out into the atmosphere. It is the correct
balance of combustion air and the chimney vent system that will ensure the
appliance provides you with its optimum performance.
Secondary air from the rear intake opening travels up the back in the
secondary air housing to the manifold located across the top and ows out
laterally to oxidize the gases below the smoke exit.
The lower combustion chamber is lined with high temperature rebricks on
2 sides, the back and across the bottom, with a layer of bre bafes at the
top to maintain a high temperature in the combustion chamber so that gases
mixing with the preheated air from the secondary air manifold tube are easily
ignited and burned. The appliance sides and back are shielded to direct the
heat upwards and forwards into the room.
Be sure to provide sufcient combustion air. There are many other
appliances in your home competing for air such as: a kitchen range hood,
forced air heating devices or a bathroom exhaust fan.
AIR INLET PATH
EXHAUST PATH
W415-1466 / B / 08.20.18
EN
7
We suggest that our woodburning hearth products
be installed and serviced by professionals who are
certified in the U.S. by the National Fireplace
Institute® (NFI) as NFI Woodburning Specialists or
who are certified in Canada by
Wood Energy Technical
Training (WETT).
Expansion / contraction noises during heating up and cooling down cycles are normal and to be expected.
After extended periods of non-operation such as following a vacation or a warm weather season, the appliance
may emit a slight odour for a few hours. This is caused by dust particles on the rebox burning off. Open a
window to sufciently ventilate the room.
2.5 E.P.A. COMPLIANCE
If you experience smoking problems, you may need to open a door, a window or otherwise provide some
method of supplying combustion air to the appliance.
W415-1466 / B
/ 08.20.18
EN
8
2.6 RATING PLATE LOCATION
For rating plate location, see “INSTALLATION
OVERVIEW” section.
NOTE: The rating plate must remain with
the appliance at all times. It must not be
removed.
This illustration is for reference only. Refer to the
rating plate on the appliance for accurate information
This wood appliance needs periodic inspection and repair for proper operation.
Consult the owner’s manual for further information. it is against federal
regulations to operate this wood appliance in a manner inconsistent with the
operating instructions in the owner’s manual. / Cet appareil au bois doit faire
l'objet d'une inspection et d'un entretien périodiques pour un fonctionnement
adéquat. Consultez le manuel d'instructions pour plus d'information. Les
règlements fédéraux interdisent d'utiliser cet appareil de chauffage d'une
manière allant à l'encontre des instructions de fonctionnement contenues dans
ce manuel.
U.S. ENVIRONMENTAL PROTECTION AGENCY Certified to comply with
2015 particulate emissions standards. Not approved for sale after May 15,2020.
Certifié conforme à la norme d’ émanation de particles de 2015. Non approuvé
pour la vente après le 15 mai, 2020. 40 CFR Part 60, Subpart AAA. 3.6 Grams
Per Hour / 2015 Crib Wood / 3.6 Grammes par heure / Crib Wood 2015.
W385-2050
MODEL / MODÈLE: EPI22
WOLF STEEL LTD
TITLE: RATING PLATE LABEL 2201
REVISION:
D: Added Dates to Standards II 05.16.12_JFK
DWG#: W385-0504
DATE:
02.17.10
MAXIMUM SIZE: 5” x 10.5”
BLACK ON WHITE BACKGROUND
MATERIAL: CLASS III A-2 PERMANENT LABEL WATERPROOF
SPECIFICATIONS: 10 MIL VELVET GLOSS LEXAN
SERIAL NUMBER TO BE ASCENDING FROM TI-2201 004810
CAUTION MINIMUM LETTER SIZE (18 POINT TYPE) AND 0.12” (8.64 POINT TYPE) FOR THE REMAINDER OF
THAT WARNING WITH VERTICAL SPACING BETWEEN LINES OF 0.046” (3.312 POINT TYPE).
LOG / FIRE WARNING SYMBOL TO BE RED
DATE CODE TO BE STAMPED IN HOUSE. EXAMPLE: January 2008 0108
HOLE TO BE Ø 0.250”
INSTALL AND USE ONLY IN ACCORDANCE WITH THE
MANUFACTURER’S INSTRUCTIONS AND LOCAL BUILDING CODES.
MINIMUM CEILING HEIGHT: 7FT (2.13m)
HEARTH EXTENSION / FLOOR PROTECTION: MUST BE
NON-COMBUSTIBLE AND EXTEND 22" IN FRONT OF THE
INSERT AND 8" ON BOTH SIDES WITH A MINIMUM
THICKNESS OF .500" (K=0.84)
CHIMNEY TYPE: MINIMUM 6” (152mm) DIAMETER APPROVED
RESIDENTIAL TYPE FOR MOBILE HOME USE A CHIMNEY
LISTED TO ULC S629 IN CANADA OR UL 103HT IN THE USA.
DO NOT OBSTRUCT SPACE UNDER HEATER.
SPECIAL METHODS ARE REQUIRED WHEN PASSING A
CHIMNEY THROUGH A WALL OR CEILING. SEE INSTRUC-
TIONS AND BUILDING CODES.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING
ANOTHER APPLIANCE.
FUEL: FOR USE WITH SOLID WOOD FUEL ONLY. DO NOT
USE GRATE OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY
ON HEARTH.
WARNING: RISK OF SMOKE SPILLAGE. OPERATE ONLY WITH
DOOR FULLY CLOSED.
REPLACE GLASS ONLY WITH CERAMIC GLASS.
DO NOT OVERFIRE. IF HEATER OR CHIMNEY CONNECTORS
GLOW, YOU ARE OVERFIRING. INSPECT AND CLEAN
CHIMNEY FREQUENTLY. UNDER CERTAIN CONDITIONS OF
USE CREOSOTE BUILD-UP MAY OCCUR RAPIDLY.
DANGER: RISK OF ELECTRICAL SHOCK. DISCONNECT
POWER BEFORE SERVICING UNIT.
INSERT: INSTALL AND USE ONLY IN SOLID FUEL BURNING
FIREPLACES. DO NOT REMOVE BRICKS OR MORTAR FROM
SOLID FUEL BURNING FIREPLACE. INSTALL WITH A
POSITIVE FLUE CONNECTOR AND FACEPLATE.
CONTACT LOCAL BUILDING FIRE OFFICIALS ABOUT RESTRIC-
TIONS AND INSTALLATION INSPECTION IN YOUR AREA.
A MINIMUM CLEARANCE OF 18” (457mm) TO THE CHIMNEY
CONNECTOR MAY BE REQUIRED BY THE AUTHORITY
HAVING JURISDICTION.
POUR INSTALLATION ET UTILISATION CONFORM
ÉMENT
AUX INSTRUCTIONS DU FABRICANT ET AUX CODES
LOCAUX DU BÂTIMENT.
HAUTEUR DE PLAFOND MINIMAL: 7PI (2,13m).
BASE DE PROTECTION/PROTECTION DE PLANCHER :
DOIT ÊTRE DE NATURE INCOMBUSTIBLE ET SE
PROLONGER DE 22" À L’AVANT DE L’ENCASTRÉ ET 8"
SUR LES CÔTÉS, ET AVOIR UNE ÉPAISSEUR MINIMALE
DE 0,500" (K = 0,84).
TYPE DE CHIMNÉE: DIAMÈTRE MINIMAL DE 6” (152mm)
APPROUVÉE POUR USAGE RÉSIDENTIEL. MAISON
MOBILE EMPLOYEZ UNE CHEMINÉE HOMOLOGUÉE ULC
S629 AU CANADA OU UL 103HT AUX ÉTATS-UNIS.
NE RIEN ENTREPOSER SOUS L’APPAREIL.
DES MÉTHODES SPÉCIALES SONT REQUISES
LORSQU’UNE CHEMINÉE TRAVERSE UN MUR OU UN
PLAFOND. VOIR LES INSTRUCTIONS ET LES CODES DU
BÂTIMENT.
NE PAS RACCORDER À LA CHEMINÉE D’UN AUTRE
APPAREIL.
COMBUSTIBLE: POUR USAGE AVEC LE BOIS
SEULEMENT. N’UTILISEZ PAS DE CHENET OU NE
SURÉLEVEZ PAS LE BOIS. PRÉPAREZ LE FEU DIRECTE-
MENT SUR L’ÂTRE.
AVERTISSEMENT: RISQUE D’ÉCHAPPEMENT DE FUMÉE.
TENIR LA PORTE FERMÉE LORSQUE LE POÊLE
FONCTIONNE. REMPLACEZ LA VITRE PAR UNE VITRE EN
CÉRAMIQUE SEULEMENT.
NE SURCHAUFFEZ PAS L’APPAREIL. SI L’APPAREIL OU
LES RACCORDS ROUGEOIENT, L’APPAREIL
SURCHAUFEE. INSPECTEZ ET NETTOYEZ LA CHEMINÉE
FRÉQUEMMENT. DANS CERTAINES CONDITIONS, DES
DÉPÔTS DE CRÉOSOTE PEUVENT SE FORMER
RAPIDEMENT.
DANGER: RISQUE DE SECOUSSE ÉLECTRIQUE.
DÉBRANCHEZ AVANT DE PROCÉDER À L’ENTRETIEN.
ENCASTRÉ: INSTALLEZ ET UTILISEZ SEULEMENT DANS
UN FOYER À COMBUSTIBLE SOLIDE. NE RETIREZ PAS DE
MORTIER, NI BRIQUES DU FOYER À COMBUSTIBLE
SOLIDE.
INSTALLEZ AVEC UNE GAINE CONFORME ET UNE
PLAQUE DE RECOUVREMENT.
RENSEIGNEZ-VOUS AUPRÈS DES AUTORITÉS LOCALES
DU BÂTIMENT ET DU SERVICE DES INCENDIES AU SUJET
DES RESTRICTIONS ET DES INSPECTIONS
D’INSTALLATION DANS VOTRE RÉGION.
UN DÉGAGEMENT MINIMAL DE 18” (457mm) JUSQU’AU
RACCORD DE LA CHEMINÉE PEUT ÊTRE EXIGÉ PAR
L’AUTORITÉ AYANT JURIDICTION.
CAUTION:
ATTENTION:
U.S. ENVIRONMENTAL PROTECTION AGENCY
Certifié
conforme à la norme d’émanation de particules de juillet 1992.
W385-0504 / D
DATE CODE / DE DATE
TI-2201
LISTED SOLID FUEL BURNING FIREPLACE INSERT
TESTED TO: / TESTÉ SELON :
UL1482 - 1996 / ULC S628 - 1993
MODEL / MODÈLE: 2201
ENCASTRÉ À COMBUSTIBLE SOLIDE HOMOLOGUÉ
HOT WHILE IN OPERATION. DO NOT
TOUCH. KEEP CHILDREN CLOTHING AND
FURNITURE AWAY. CONTACT MAY CAUSE
SKIN BURNS.
QUAND L’APPAREIL FONCTIONNE, LA
SURFACE DEVIENT CHAUDE. NE PAS
TOUCHER. TENIR LES ENFANTS, LES
VÊTEMENTS ET LES MEUBLES À
L’ÉCART. LE CONTACT PEUT CAUSER
DES BRÛLURES À LA PEAU.
A
B
C
D
E
F
G
WOLF STEEL LTD.
24 NAPOLEON ROAD,
BARRIE, ON, L4M 0G8 CANADA
NAC GUANGZHOU P.R.C.
NO.69 HEFENG ROAD,
GUANGZHOU,CHINA
CLEARANCE TO COMBUSTIBLE CONSTRUCTION / DÉGAGEMENTS AUX MATÉRIAUX COMBUSTIBLES:
(MEASURED TO UNIT / À PARTIR DE L’APPAREIL)
UNIT /
APPAREIL
ADJACENT
SIDE WALL
(TO SIDE) /
MUR LATÉRAL
ADJACENT (AU
CÔTÉ)
A
MANTLE
(TO TOP) /
MANTEAU
(JUSQU’AU
DESSUS)
B
TOP FACING
(TO TOP) /
HAUT DE LA
FAÇADE
(JUSQU’AU
DESSUS)
C
SIDE FACING
(TO SIDE) /
CÔTÉ DE LA
FAÇADE (AU
COTÉ)
D
MINIMUM
HEARTH
EXTENSION /
BASE DE
PROTECTION
MINIMALE
E
MINIMUM
HEARTH
THICKNESS /
ÉPAISSEUR
MINIMALE DE LA
BASE DE
PROTECTION
F
MINIMUM
HEARTH SIDE
EXTENSION /
BADE DE
PROTECTION
LATÉRALE
MINIMALE
G
2201 8”1”22”10”22”30”16”
REPORT NO. 415-S-08-2
B
D
SAMPLE
W415-1466 / B / 08.20.18
EN
9
3.0 PRE-INSTALLATION PREPARATION
Clean all ashes out of the inside of the existing replace opening. Make sure that the chimney and replace are
free of cracks, loose mortar, creosote deposits, blockage or other signs of deterioration. If necessary, have any
repair work done by a qualied professional before installing the insert.
Do NOT remove bricks or mortar from the replace. In case of an outside air inlet or ash dump, ll with ber-
glass insulation. Adhere to minimum clearances as illustrated.
Combustible material must not protrude more than 1" (25mm) to the side of the insert or between the mantel
and the top of the insert.
MINIMUM CLEARANCES
A Sidewall 16" (406mm)
B Mantel 30" (762mm)
C Top facing 22" (559mm)
D Side facing 10" (254mm)
E Hearth (front) 22" (559mm)
F Hearth (side) 8" (203mm)
G In front of
insert
48" (1219mm)
MINIMUM APPLIANCE SIZE
H Width (rear) 25 7/8" (657mm)
I Width (front) 25 7/8" (657mm)
J Height (front) 22" (559mm)
K Height (rear) 22" (559mm)
L Depth 14" (356mm)
M Hearth depth 22" (559mm)
N Hearth width 41 3/8" (1051mm)
O Facing width 45 3/8" (1153mm)
P Facing height 42 5/8" (1083mm)
Q Mantel 50 5/8" (1286mm)
A
D
C
B
E
G
F
P
M
Q
N
J
K
L
H
I
O
3.1 MINIMUM CLEARANCE TO COMBUSTIBLES
HEARTH EXTENSION / FLOOR
PROTECTION:
Must be non-combustible and extend
18" (457mm) in front of the insert and 8"
(203mm) on both sides with a minimum
thickness of 1" (25mm) and a thermal
conductivity factor (K) 0.84.
W415-1466 / B
/ 08.20.18
EN
10
4.0 INSTALLATION
68.3C
!
WARNING
WEAR GLOVES AND SAFETY GLASSES FOR PROTECTION.
CAREFULLY FOLLOW THE INSTRUCTIONS FOR ASSEMBLY OF THE PIPE AND OTHER PARTS
NEEDED TO INSTALL THE APPLIANCE. FAILURE TO DO SO MAY RESULT IN A FIRE, ESPECIALLY IF
COMBUSTIBLES ARE TOO CLOSE TO THE APPLIANCE OR CHIMNEY AND AIR SPACES ARE
BLOCKED, PREVENTING THE FREE MOVEMENT OF COOLING AIR.
DO NOT DRAW OUTSIDE AIR FROM GARAGE SPACES. EXHAUST PRODUCTS OF GASOLINE ENGINES
ARE HAZARDOUS. DO NOT INSTALL OUTSIDE AIR DUCTS SUCH THAT THE AIR MAY BE DRAWN
FROM ATTIC SPACES, BASEMENTS OR ABOVE THE ROOFING WHERE OTHER HEATING APPLIANCES
OR FANS AND CHIMNEYS EXHAUST OR UTILIZE AIR. THESE PRECAUTIONS WILL REDUCE THE
POSSIBILITY OF APPLIANCE SMOKING OR AIR FLOW REVERSAL. THE OUTSIDE AIR INLET MUST
REMAIN CLEAR OF LEAVES, DEBRIS ICE AND/OR SNOW. IT MUST BE UNRESTRICTED WHILE
APPLIANCE IS IN USE TO PREVENT ROOM AIR STARVATION WHICH CAN CAUSE SMOKE SPILLAGE
AND AN INABILITY TO MAINTAIN A FIRE. SMOKE SPILLAGE CAN ALSO SET OFF SMOKE ALARMS.
NEGATIVE PRESSURE WITHIN YOUR HOME MAY INADVERTENTLY AFFECT YOUR APPLIANCE.
TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE APPLIANCE MUST NOT BE
INSTALLED AGAINST VAPOUR BARRIERS OR EXPOSED INSULATION. LOCALIZED OVERHEATING
COULD OCCUR AND A FIRE COULD RESULT.
DO NOT USE MAKESHIFT COMPROMISES DURING INSTALLATION. DO NOT BLOCK OR RESTRICT
AIR, GRILLE OR LOUVRE OPENINGS. DO NOT ADD A HOOD.
TO PREVENT PERSONAL INJURY KEEP HAND TOOLS IN GOOD CONDITION, SHARPEN CUTTING
EDGES AND MAKE SURE TOOL HANDLES ARE SECURE.
ALWAYS MAINTAIN THE MINIMUM AIR SPACE REQUIRED TO THE ENCLOSURE TO PREVENT FIRES.
It is extremely important that your appliance be installed according to the manufacturer's specications. The
manufacturer's installation instructions and specied clearances should always be followed in accordance with
local and national codes. In Canada the CSA B365 and the CSA C22.1 installation codes are to be followed. In
the USA the ANSI NFPA 70 and ANSI NFPA 211 installation codes are to be followed.
Chimney and liner must be in good condition and kept clean.
W415-1466 / B / 08.20.18
EN
11
4.1 TYPICAL EXISTING MASONRY
You can install your appliance using your existing masonry chimney. To do
so, follow the guidelines below. If you are using a masonry chimney, it
is important that it be built in compliance with the speci cations of the
Building Code in your region. It must normally be lined with  re clay
bricks, metal or clay tiles sealed together with  re cement. (Round
ues are the most ef cient).
62.2
FOLLOW MANUFACTURER’S
INSTRUCTIONS FOR
MAXIMUM LINER EXTENSION
ABOVE CHIMNEY
FLOOR
PROTECTOR
DAMPER PLATE
REMOVED OR
FASTENED IN OPEN
POSITION
SEAL WITH NON-
COMBUSTIBLE
MATERIAL
MASONRY
CHIMNEY MUST
HAVE
STRUCTURAL
INTEGRITY
LISTED
CHIMNEY
LINER
A. Remove the replace damper or fasten it permanently open.
* We recommend the following method of sealing off the damper area around the liner.
B. * Measure the throat of the replace and mark this shape on a piece of 24 gauge sheet metal (ue
cover); cut a six-inch (6.75" / 171mm) hole to lie directly below the replace ue opening. Allow two
inches of material for a ange on all sides and cut to these measurements. Bend down the anges. If you
have never done this before, it might be a good idea to make a cardboard pattern and test it rst. Fasten
this ue cover in position as high as possible with two masonry screws per side through the anges into
the replace.
In Canada: Install a listed 6" (152mm) diameter exible stainless steel liner from the top of the chimney to the
insert ue collar. Attach a stainless steel liner connector or elbow to the liner and insert onto the ue collar. Fasten
with three screws. Secure the top of the liner to the chimney cap using a liner support and chimney ashing. Cap
the top of the chimney liner assembly using an approved rain cap.
In the United States: While it is not required, it is recommended that a chimney liner be installed that is
continuous from the insert to the top of the chimney, particularly when the insert is installed in a basement. For
this type of connection, use the “In Canada” installation instructions above.
If a continuous liner is not installed, a “direct ue connection” must be made. The direct ue connection requires a
non-combustible connector that extends from the insert into the chimney ue liner and also that the installed ue
cover be sealed below the entry point of the connector to prevent dilution of combustion products in the chimney
ue with air from inside the house. Cap the top of the chimney using an approved rain cap.
The following installation requirements must be observed when installing solid fuel burning inserts into factory
built replaces.
W415-1466 / B
/ 08.20.18
EN
12
4.2 FACTORY BUILT FIREPLACE
The following installation requirements must be observed when installing solid fuel burning inserts into factory
built  replaces.
A.
The factory built  replace must be listed per UL 127 or ULC S610.
B.
Clearances to any combustible material surrounding this insert as identi ed must be followed. These
clearance requirements supersede any pre-existing facing material clearances listed for the factory
built  replace.
C.
Installation must include a full height listed chimney liner meeting HT requirements (2100°F/1149°C)
as required in UL 1777 (U.S.) or ULC S635 (Canada). The liner must be securely attached to the insert
ue collar and the chimney top.
D.
Means must be provided to prevent room air passage to the chimney cavity of the  replace. This may
be accomplished by sealing the damper area around the chimney liner, or sealing the appliance front.
E.
The air  ow within and around the appliance shall not be altered by the installation of the insert (i.e.
no louvres or cooling air inlet or outlet ports are blocked), unless speci cally tested as such for each
factory built  replace manufacturer and model line. NOTE: Using a louvered face plate (surround)
complies with this requirement.
F.
Alteration of the appliance in any manner is not permitted with the following exceptions;
A. External trim pieces which do not affect the operation of the appliance may be removed providing
they can be stored on or within the  replace for reassembly if the insert is removed.
B. The chimney damper may be removed to install the chimney liner.
G.
Circulating air chambers (i.e. in a steel  replace liner or metal heat circulator) shall not be blocked.
H.
Means must be provided for removal of the insert to clean the chimney  ue.
I.
Inserts that project in front of the  replace must be supplied with appropriate support means.
J.
A permanent metal warning label must be attached to the back of the  replace stating that the  replace
must be restored to its original condition for safe use without the insert.
80.2B
W415-1466 / B / 08.20.18
EN
13
5.0 FINISHING
5.1 SECONDARY AIR TUBES
A. Start at the back working forwards, install the
secondary air tube by inserting the tube
into the hole, as illustrated in “A”.
B. Slide the tube into the opposite hole.
With the holes on the secondary air
tube pointing forward, align the
tube with the tube retainer
and insert the cotter
pin, as illustrated
in“B”.
C. Spread the cotter pin
to retain.
NOTE: There are 4
secondary air tubes. One
of the tubes has larger
holes. This tube is to be
located closest to the
front of the appliance, as
illustrated in “C”.
B
COTTER PIN
TUBE
RETAINER
C
A
HOLE
W415-1466 / B
/ 08.20.18
EN
14
5.2 DOOR INSTALLATION
Hang the door using the hinge pins supplied.
5.3 DOOR HANDLE INSTALLATION
DOOR
HANDLE
DOOR HANDLE
LATCH
LOCK
NUT
DOOR
SPACER
FRONT VIEW
NOTE: Position of
door handle latch.
98.1
NOTE: DOOR MAY NOT BE AS
ILLUSTRATED
SPRING
WASHER
Twist the large wire handle over the end of the handle rod. Twist the smaller wire handle over the end of the air control rod
above the door.
W415-1466 / B / 08.20.18
EN
15
!
WARNING
5.4 BRICKS AND BAFFLES INSTALLATION
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
E
C
B
A
D
D
E
With the appliance and chimney installation completed, move the bricks into place as illustrated below.
A. Install the bottom nine (A) bricks and one (B) brick, working from the back of the appliance forward as
illustrated.
B. Install four (A) bricks along both sides of the appliance.
C. Install the four (A) bricks and one (C) brick along the back wall by pivoting the bricks up under the brick
retainer. NOTE: Place narrow (C) brick in centre.
D. Install two (D) bricks along the front of the appliance below the ledge at the bottom of the door
opening.
E. Carefully pivot two (E) bre bafes up onto the secondary air tubes as illustrated. Ensure that the top
bafes are pushed all the way to the rear of the rebox, leaving a minimum of a 1 inch gap along the
front. This will allow the ue gases to escape the rebox. Ensure overlap joint is tight.
BAFFLE
SECONDARY
AIR TUBES
OVERLAP
JOINT
OPERATION OF THE APPLIANCE WITHOUT THE BAFFLES CAN RESULT IN EXCESSIVE TEMPERA-
TURES THAT COULD DAMAGE THE APPLIANCE, CHIMNEY AND THE SURROUNDING ENCLO-
SURE.
W415-1466 / B
/ 08.20.18
EN
16
5.5 FLASHING INSTALLATION
A. With the ashing close to its nal position, assemble sides as illustrated using the supplied fasteners.
B. The ashing position on the insert is adjustable, allowing for varying replace cavity and/or hearth
depths. Engage the tabs on the assembled side ashings into the appropriate slots on the insert for
the desired nal location.
C. Adjust the blower chute tightly against the ashing and secure it in place.
D. Insert the top piece as illustrated, then bolt together using the screws, lock washers and weldnuts
provided.
E. Slide the appliance back into position.
BLOWER
CHUTE
W415-1466 / B / 08.20.18
EN
17
!
WARNING
5.6 BLOWER INSTALLATION
Drywall dust will penetrate into the blower bearings, causing irreparable damage. Care must be taken to
prevent drywall dust from coming into contact with the blower or its compartment. Any damage resulting from
this condition is not covered by the warranty policy. Use of the blower increases the output of heat.
This blower is thermally activated. Depending on the intensity of the re, the blower will start 15-30 minutes
after lighting. The thermal switch for the appliance is afxed to an adjustable bracket, which should be
positioned so it is in contact with the blower housing as illustrated.
For shipping purposes the blower housing has
been stored within the rebox. We recommend
removing the door prior to installing the blower.
A. Remove the two screws securing the
cover and set aside.
B. Engage the clips onto the retainer
bracket and secure using the screw
supplied.
C. Reattach the cover with the two screws
previously removed.
BLOWER
HOUSING
COVER
CLIPS
RETAINER
BRACKET
ADJUSTABLE
RISK OF FIRE AND ELECTRICAL SHOCK.
TURN OFF THE ELECTRICAL POWER BEFORE SERVICING THIS APPLIANCE.
USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH
THIS APPLIANCE. USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS,
ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICA-
TION.
ENSURE THAT THE BLOWER’S POWER CORD IS NOT IN CONTACT WITH ANY SURFACE OF THE
APPLIANCE TO PREVENT ELECTRICAL SHOCK OR FIRE DAMAGE. DO NOT RUN THE POWER
CORD BENEATH THE APPLIANCE.
W415-1466 / B
/ 08.20.18
EN
18
6.0 OPERATION
Your Timberwolf EPA listed product is designed with the most advanced technology. The appliance is extremely
airtight.
The rst re(s) in your appliance will be difcult to get going and keep going with little amount of heat being generated.
This is a result of the moisture being driven out of the re brick. During the break-in period (the rst 2 or 3 res) create
only small, res using kindling; this will allow the rebrick to cure. Do not be alarmed if small hairline cracks develop in
the rebrick. This is a normal occurrence and does not pose a safety hazard. The paint may also smell a little for the
rst few res as it cures and you may wish to open a door or window to alleviate the smell.
To start, a brisk re is required. Place loosely crumpled paper on the oor of the appliance and cover with dry kindling.
Open the air control fully by sliding control all the way to the right. Light the paper and leave the door slightly ajar (one
inch) until all kindling is burning. To maintain a brisk re, a hot coal bed must be established and sustained.
Slowly add larger wood (2x4 size pieces). Lay the pieces lengthwise from side to side in the hot coal bed with a
shallow trench between, so that the primary air can ow directly into this trench and ignite the fuel above. When the re
seems to be at its peak, medium sized logs may be added. Once these logs have caught re, carefully close the door.
(Closing the door too quickly after refueling will reduce the rebox temperature and result in an unsatisfactory burn.)
Remember it is more efcient to burn medium sized wood, briskly, and refuel frequently than to load the appliance with
large logs that result in a smouldering, inefcient re and dirty glass.
As soon as the door is closed, you will observe a change in the ame pattern. The ames will get smaller and lazier
because less oxygen is getting into the combustion chamber. The ames, however, are more efcient. The ames will
remain lazy but become larger again as soon as the rebricks have been heated thoroughly and the chimney becomes
heated and provides a good draft. At this point, the roaring re that you see when the door is opened is wastefully
drawing heated room air up the chimney, certainly not desirable. Always operate with the door fully closed once the
medium sized logs have caught re.
!
WARNING
ALWAYS OPERATE THIS APPLIANCE WITH THE DOOR CLOSED AND LATCHED EXCEPT DURING
START UP AND RE-FUELING. ALWAYS WEAR GLOVES TO PREVENT INJURY. DO NOT LEAVE THE
FIRE UNATTENDED WHEN THE DOOR IS UNLATCHED AS UNSTABLE WOOD COULD FALL OUT OF
THE FIRE CHAMBER CREATING A FIRE HAZARD TO YOUR HOME.
NEVER LEAVE CHILDREN UNATTENDED WHEN THERE IS A FIRE BURNING IN THE APPLIANCE.
NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER
FLUID, OR SIMILAR LIQUIDS TO START OR ‘FRESHEN UP’ A FIRE IN THIS APPLIANCE. KEEP ALL
SUCH LIQUIDS WELL AWAY FROM THE APPLIANCE WHILE IT IS IN USE.
OBJECTS PLACED IN FRONT OF THE APPLIANCE SHOULD BE KEPT A MINIMUM OF 48”
FROM THE FRONT FACE.
ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN APPROVED IN WRITING BY THE
TESTING AUTHORITY IS CONSIDERED BREACHING CSA B365 (CANADA) AND ANSI NFPA 211
(USA).
OPEN AIR CONTROL (AND DAMPER WHEN FITTED) BEFORE OPENING FIRING DOOR.
HOT WHILE IN OPERATION, KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY
CAUSE SKIN BURNS. WEAR GLOVES TO OPERATE YOUR APPLIANCE.
BURNING YOUR APPLIANCE WITH THE DOORS OPEN OR AJAR CREATES A FIRE HAZARD
THAT MAY RESULT IN A HOUSE AND OR CHIMNEY FIRE.
THIS WOOD APPLIANCE HAS A MANUFACTURER-SET MINIMUM LOW BURN RATE THAT MUST
NOT BE ALTERED. IT IS AGAINST FEDERAL REGULATIONS IN THE UNITED STATES TO ALTER THIS
SETTING OR OTHERWISE OPERATE THIS WOOD APPLIANCE IN A MANNER INCONSISTENT WITH
OPERATING INSTRUCTIONS IN THIS MANUAL.
W415-1466 / B / 08.20.18
EN
19
You can now add larger pieces of wood and operate the appliance normally. Once the appliance is entirely hot,
it will burn very efciently with little smoke from the chimney. There will be a bed of orange coals in the rebox
and secondary ames ickering just below the top bafes. You can safely ll the rebox with wood to the top of
the door and will get best burns if you keep the appliance pipe temperatures between 250°F (120°C) and 450°F
(270°C). A surface thermometer will help regulate this.
Without an appliance thermometer, you are working blindly and have no idea of how the appliance is operating!
An appliance thermometer offers a guide to performance.
Can’t get the re going? Use more kindling and paper. Assuming the chimney and vent are sized correctly and
there is sufcient combustion air, the lack of sufciently dry quantities of small kindling is the problem. Thumb
size is a good gauge for small kindling diameter.
Can’t get heat out of the appliance? One of two things may have happened. The appliance door may have
been closed prematurely and the appliance itself has not reached optimum temperature. Reopen the door and/
or draft control to re-establish a brisk re. The other problem may have been wet wood. The typical symptom is
sizzling wood and moisture being driven from the wood.
6.1 OPTIMUM BURN METHOD
For optimal emissions performance and efciency follow these simple guidelines when using your appliance:
A. Maintain a 2" (51mm) deep, hot, glowing red coal bed.
B. Burn dry seasoned wood with less than 20% moisture content and burn so that the glass door remains
clean.
C. A stove thermometer should indicate 350°F (176°C) as an average temperature.
D. Maintain a minimal trace of smoke coming from the chimney when the appliance is burning as
intended.
E. Inspect and replace all necessary components such as gaskets, manifolds, glass and other
components which may affect the overall appliance performance.
F. Ensure an adequate draft to control burn rate and temperature.
Refer to “OPERATION” and “MAINTENANCE” sections for detailed information.
W415-1466 / B
/ 08.20.18
EN
20
6.2 AIR CONTROL
Draft is the force which moves air from the rebox up through the chimney.
The amount of draft in your chimney depends on the length and diameter of
chimney, local geography, nearby obstructions and other factors. Adjusting
the air control all the way to the left reduces the temperature. The draft can be
adjusted from low to high by moving the handle from left to right. Inadequate
draft may cause back-pufng into the room through the appliance and chimney
connector points and may cause plugging of the chimney. Too much draft may
cause an excessive temperature in the appliance, glowing red appliance parts
or chimney connectors or an uncontrollable burn which can lead to a chimney
re or permanent damage to the appliance. Do not operate your appliance for
longer than 30 minutes with the air control on “HIGH” (fully open).
When loading the appliance, ensure that the two upper bre bafes are not lifted up and off their ledge. For
maximum efciency, when the appliance is thoroughly hot, load it fully to the top of the door opening and burn
at a medium low setting. Maximum heat for minimum fuel (optimum burn) occurs when the appliance top
temperature is between 500°F (260°C) and 600°F (315°C). The bricks will be nearly all white and the glass
mostly clear. The whiteness of the bricks and the cleanliness of the glass are good indicators of your operating
efciency. Not enough heat is produced when only one or two pieces of wood are burned or the wood may not
burn completely. A minimum of three pieces are needed to encase a bed of coals that sustains the re.
NOTE: When loading the appliance, ensure to keep fuel back from the glass. If coals are to accumulate
on the front lip, there is a chance they will fall out when the door is opened.
Loosely stacked wood burns quicker than a tightly packed load. Wood burns in cycles rather than giving a steady
output of heat. It is best to plan these cycles around your household routine so that only enough coals are left to
start the next load. In the evening, load your appliance, at least, a half-hour before bed to ensure a good re, hot
enough to close the draft control for an overnight burn.
Burn only dry seasoned wood with 20% moisture content .It produces more heat and less soot or creosote. Do
not burn ocean beach wood. Its salt content can produce a metal eating acid. When refueling open the door
slowly to prevent smoke spillage. Use a pair of long gloves (barbecue gloves) when feeding the re. Because
these appliances burn at the front, they are clean and efcient, but they are also very hot and gloves are useful.
Keep a small steel shovel nearby to use as a poker and to remove ashes. Do not store the wood within 3 feet
(1m) of the appliance.
AIR CONTROL
6.3 FIRE EXTINGUISHERS / SMOKE DETECTORS
!
WARNING
DO NOT STORE FUEL WITHIN THE CLEARANCE TO COMBUSTIBLES, OR IN THE SPACE REQUIRED
FOR RE-FUELING AND ASH REMOVAL.
BURNING WET, UNSEASONED WOOD CAN CAUSE EXCESSIVE CREOSOTE ACCUMULATION. WHEN
IGNITED IT CAN CAUSE A CHIMNEY FIRE THAT MAY RESULT IN A SERIOUS HOUSE FIRE.
91.1A
All homes with a solid fuel burning appliance should have at least one  re extinguisher in a central location,
known to all and at least one smoke detector and carbon monoxide (CO) detector in the room containing the
appliance. If the smoke detector sounds an alarm, correct the cause but do not de-activate or relocate the
smoke detector. If the carbon monoxide detector sounds an alarm, immediately vent the area, evacuate and
call your local  re department.
6.4 FUEL
!
WARNING
THIS WOOD APPLIANCE HAS A MANUFACTURER-SET MINIMUM LOW BURN RATE THAT MUST
NOT BE ALTERED. IT IS AGAINST FEDERAL REGULATIONS IN THE UNITED STATES TO ALTER THIS
SETTING OR OTHERWISE OPERATE THIS WOOD APPLIANCE IN A MANNER INCONSISTENT WITH
OPERATING INSTRUCTIONS IN THIS MANUAL.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

NAPOLEON EPI22 Manuel utilisateur

Catégorie
Poêles
Taper
Manuel utilisateur

dans d''autres langues