Greenheck 453905 TAUD/TAUB Mode d'emploi

Marque: Greenheck

Modèle: 453905 TAUD/TAUB

Taper: Mode d'emploi

Document 453905

Models TAUD, TAUB-CA and TAUB

Tube Axial Upblast Fans

Tube Axial Upblast Fans 1

Installation, Operation and Maintenance Manual

Please read and save these instructions for future reference. Read carefully before attempting to assemble,

install, operate or maintain the product described. Protect yourself and others by observing all safety

information. Failure to comply with these instructions will result in voiding of the product warranty and may

result in personal injury and/or property damage.

Only qualiﬁed personnel should install this fan.

Personnel should have a clear understanding of these

instructions and should be aware of general safety

precautions. Improper installation can result in electric

shock, possible injury due to coming in contact with

moving parts, as well as other potential hazards.

Other considerations may be required if seismic

activity is present. If more information is needed,

contact a licensed professional engineer before

moving forward.

1. Follow all local electrical and safety codes, as

well as the National Electrical Code (NEC) and the

National Fire Protection Agency (NFPA), where

applicable. Follow the Canadian Electric Code

(CEC) in Canada.

2. The rotation of the propeller is critical. It must

be free to rotate without striking or rubbing any

stationary objects.

3. Motor must be securely and adequately grounded.

4. Do not spin fan propeller faster than max

cataloged fan RPM. Adjustments to fan speed

with a Variable Frequency Drive (VFD) may affect

motor load. If the fan RPM is changed, the motor

current should be checked to make sure it is not

exceeding the motor nameplate amps.

5. Do not allow the power cable to kink or come in

contact with oil, grease, hot surfaces or chemicals.

Replace cord immediately if damaged.

6. Verify that the power source is compatible with the

equipment.

General Safety Information

TAUB

TAUD

DANGER

Always disconnect, lock and tag power source

before installing or servicing. Failure to disconnect

power source can result in fire, shock or serious

injury.

CAUTION

When servicing the fan, motor may be hot enough

to cause pain or injury. Allow motor to cool before

servicing.

CAUTION

Precaution should be taken in explosive

atmospheres.

DANGER

Pour écarter les risques d’incendie, de choc

électrique ou de blessure grave, veiller à toujours

débrancher, verrouiller et étiqueter la source de

courant avant l’installation ou l’entretien.

ATTENTION

Lors de toute intervention sur la soufflante, le moteur

peut être suffisamment chaud pour provoquer

une douleur voire une blessure. Laisser le moteur

refroidir avant toute maintenance.

ATTENTION

Faire preuve de précaution dans les atmosphères

explosives.

7. Never open access doors to a duct while the fan is

running.

Tube Axial Upblast Fans2

Receiving

Upon receiving the product, check to ensure all

items are accounted for by referencing the delivery

receipt or packing list. Inspect each crate or carton

for shipping damage before accepting delivery. Alert

the carrier of any damage detected. The customer

will make a notation of damage (or shortage of items)

on the delivery receipt and all copies of the bill of

lading which is countersigned by the delivering

carrier. If damaged, immediately contact your local

representative. Any physical damage to the unit after

acceptance is not the responsibility of manufacturer.

Unpacking

Verify that all required parts and the correct quantity

of each item have been received. If any items are

missing, report shortages to your local representative

to arrange for obtaining missing parts. Sometimes it

is not possible that all items for the unit be shipped

together due to availability of transportation and truck

space. Conﬁrmation of shipment(s) must be limited to

only items on the bill of lading.

Handling

Fans are to be rigged and moved by the lifting

brackets provided or by the skid when a forklift is

used. Location of brackets varies by model and size.

Handle in such a manner as to keep from scratching

or chipping the coating. Damaged ﬁnish may reduce

the ability of the fan to resist corrosion. Fans should

never be lifted by the fan housing, motor, motor cover,

windband or accessories.

Storage

• Rotate propeller monthly and purge bearings once

every three months.

• Energize fan motor once every three months.

• Store belts ﬂat to keep them from warping and

stretching.

• Store unit in a location which does not have

vibration.

• After storage period, purge grease before putting

fan into service.

If storage of fan is in a humid, dusty or corrosive

atmosphere, rotate the fan and purge the bearings

once a month. Improper storage which results in

damage to the fan will void the warranty.

Fans are protected against damage during shipment.

If the unit cannot be installed and operated

immediately, precautions need to be taken to prevent

deterioration of the unit during storage. The user

assumes responsibility of the fan and accessories

while in storage. The manufacturer will not be

responsible for damage during storage. These

suggestions are provided solely as a convenience to

the user.

INDOOR -

The ideal environment for the storage of

fans and accessories is indoors, above grade, in a

low humidity atmosphere which is sealed to prevent

the entry of blowing dust, rain or snow. Temperatures

should be evenly maintained between 30° to 110°F

(-1° to 43°C), wide temperature swings may cause

condensation and “sweating” of metal parts. All

accessories must be stored indoors in a clean, dry

atmosphere.

Remove any accumulations of dirt, water, ice, or snow

and wipe dry before moving to indoor storage. To

avoid “sweating” of metal parts allow cold parts to

reach room temperature. To dry parts and packages

use a portable electric heater to remove any moisture

buildup. Leave coverings loose to permit air circulation

and to allow for periodic inspection.

The unit should be stored at least 3½ inches

(89 mm)

off the ﬂoor on wooden blocks covered with moisture

proof paper or polyethylene sheathing. Aisles between

parts and along all walls should be provided to permit

air circulation and space for inspection.

OUTDOOR - Fans designed for outdoor applications

may be stored outdoors, if absolutely necessary.

Roads or aisles for portable cranes and hauling

equipment are needed.

The fan should be placed on a level surface to prevent

water from leaking into the fan. The fan should be

elevated on an adequate number of wooden blocks

so it is above water and snow levels and has enough

blocking to prevent it from settling into soft ground.

Locate parts far enough apart to permit air circulation,

sunlight and space for periodic inspection. To

minimize water accumulation, place all fan parts on

blocking supports so rain water will run off.

Do not cover parts with plastic ﬁlm or tarps as these

cause condensation of moisture from the air passing

through heating and cooling cycles.

Inspection and Maintenance During

Storage

While in storage, inspect fans once per month. Keep a

record of inspection and maintenance performed.

If moisture or dirt accumulations are found on parts,

the source should be located and eliminated. At each

inspection, rotate the fan propeller by hand ten to

ﬁfteen revolutions to distribute lubricant in motor and

bearings. Every three months, the fan motor should be

energized. If paint deterioration begins, consideration

should be given to touch-up or repainting. Fans with

special coatings may require special techniques for

touch-up or repair.

Machined parts coated with rust preventive should be

restored to good condition promptly if signs of rust

occur. Immediately remove the original rust preventive

coating with petroleum solvent and clean with lint-

free cloths. Polish any remaining rust from surface

with crocus cloth or ﬁne emery paper and oil. Do not

destroy the continuity of the surfaces. Thoroughly

Tube Axial Upblast Fans 3

Table of Contents

General Safety Information .................. 1

Receiving, Unpacking, Handling, Storage ....... 2

Inspection and Maintenance During Storage .... 3

Removing from Storage ..................... 3

General Information

Unit and System Identification Tags ........... 4

Pre-Installation Information .................. 4

Electrical Disconnects ...................... 4

Moving Parts ............................. 4

Guards - Motor Cover or Inlet Guard .......... 4

Inspection Door ........................... 4

Air Pressure and Suction .................... 4

Fans - Rigging and Lifting ................... 5

Electrical Connections ...................... 5

UL/cUL Listed Smoke Exhaust ............... 6

Unit Start-Up

Visual Inspection of Equipment ............... 7

Check ................................... 7

Additional Steps for Initial Start-Up ............ 7

Electrical Connections ...................... 7

Routine Maintenance and Operation

Fan Operation ............................ 8

Motors .................................. 8

Fasteners and Set Screws ................... 8

Direct Drive Fans .......................... 8

Belt Drive Fans ...........................8-9

V-Belt Replacement ........................ 9

Alignment of Pulleys and Belts ............... 9

Field Coating Touch-Up Procedure for

Scratched Areas .......................... 10

Variable Frequency Drive Operation .......... 10

Parts List ............................... 11

Maintenance Log ...................Backcover

Our Commitment ...................Backcover

wipe clean with Tectyl

506 (Ashland Inc.) or the

equivalent. For hard to reach internal surfaces or for

occasional use, consider using Tectyl

511M Rust

Preventive, WD-40

® or the equivalent.

Removing from Storage

As fans are removed from storage to be installed

in their ﬁnal location, they should be protected and

maintained in a similar fashion until the fan equipment

goes into operation.

Prior to assembly and installation of the unit and

system components, inspect the fan assembly to

make sure it is in working order.

1. Check all fasteners, set screws on the fan,

propeller, bearings, drive, motor base and

accessories for tightness.

2. Rotate the fan propeller by hand and assure no

parts are rubbing.

3. Fans should not be lifted by the fan housing,

motor, motor cover, windband or accessories.

Tube Axial Upblast Fans4

General Information

Guards – Motor Cover or Inlet Guard

Do not operate fans without proper protective devices

in place. Failure to do so may result in serious bodily

injury and property damage. Check local codes to

ensure compliance for all protective devices.

Inspection Door

Before opening the inspection door, ensure the fan

propeller has stopped moving and that the propeller

has been secured from being able to rotate. Do not

operate fan without inspection door in its fully closed

position.

Air Pressure and Suction

In addition to the usual hazards associated with

rotating machinery, fans also create a dangerous

suction at the inlet. Special caution needs to be used

when moving around a fan, whether it is in operation

or not. Before start-up, make sure the inlet area is

clear of personnel and loose objects.

To ensure a successful installation, the instructions in

this manual should be read and adhered to. Failure to

comply with proper installation procedures may void

the warranty.

Unit and System Identiﬁcation Tags

Each fan has a permanently afﬁxed manufacturer’s

engraved metal nameplate containing the model

number and individual serial number.

The tag shown is an example of an identiﬁcation

nameplate on the fan. The information provides

general details about the fan, as well as containing

speciﬁc information

unique to the unit.

When contacting

your local

manufacturer’s

representative with

future needs or

questions, have the information on this label available.

Tags are mounted in an area which is clearly visible,

usually on the side of the fan housing.

Pre-Installation Information

Before installation, it is important to be certain the

mounting surface will bear the operating weight of the

fan. For proper fan operation, it is also important that

it be operated in a completely level position.

For further details on safety practices involving

industrial and commercial fans, please refer to AMCA

Publication410.

Electrical Disconnects

All fan motors should have disconnects located in

close visual proximity to turn off electrical service.

Service disconnects shall be locked-out when

maintenance is being performed.

Moving Parts

All moving parts must have guards to protect

personnel. Refer to local codes for requirements

as to the number, type and design. Fully secure fan

propeller before performing any maintenance. The fan

propeller may start “free wheeling” even if all electrical

power has been disconnected. Before the initial start-

up or any restart, check the following items to make

sure that they are installed and secure.

• Do not spin fan propeller faster than the maximum

cataloged fan RPM.

• Adjustments to fan speed signiﬁcantly affects

motor load. If the fan RPM is changed, the motor

current should be checked to make sure it is not

exceeding the motor nameplate amps.

Tube Axial Upblast Fans 5

Fans – Rigging and Lifting

IMPORTANT

Fans should never be lifted by the housing, motor,

motor cover, windband or accessories.

1. Before lifting, be sure that all shipping materials

have been removed from the fan.

2. Use standard lifting and rigging practices.

3. ALL lifting brackets on each fan must be utilized at

the same time.

4. Fan to be kept level during lifting and installation.

5. Spreader bars are recommended and must span

the fan to prevent damage to the damper section

of the fan by the lifting cables.

6. Always test-lift the fan to check for proper balance

and rigging before hoisting to desired location.

7. Never lift fan in windy conditions.

8. Preparation of roof opening should be completed

prior to lifting fan to the roof.

9. Carefully lift the fan to the roof curb and install

fasteners in all holes provided in the unit base.

The windband need not be removed for the lifting

operation.

Fans are to be rigged and moved by the lifting

brackets shown in Figure 1 or by the skid when a

forklift is used. Location of brackets varies by model

and size.

Handle in such a manner as to keep from scratching

or chipping the coating. Damaged ﬁnish may reduce

ability of fan to resist corrosion. See coating repair

section of this manual for details regarding touch-up

of damaged surfaces.

The electrical supply must be compatible with the

fan motor voltage, phase and amperage capacity.

The electrical supply line must be properly fused and

conform to local and national electrical codes.

For direct drive units, the electrical supply may

be routed internally and exit through a hole provided

in the fan housing if an optional service disconnect

switch is provided.

For belt drive units, the electrical supply line

may be routed internally and exit the fan housing

through a hole provided below the belt tube opening.

The electrical supply line should then be either: (1)

connected to an optional service disconnect switch,

or (2) wired directly to the motor.

For belt drive units in continuous high

temperature installations, the electrical supply

must be kept out of the airstream. This means

bringing the supply lines off the roof deck not through

the fan. The electrical supply line should then be

either: (1) connected to an optional service disconnect

switch, or (2) wired directly to the motor.

For belt drive units in emergency smoke

removal installations, the electrical supply must

be kept out of the airstream. They may also require

an isolated power supply so that if power is cut to the

building in the event of a fire, the fan will continue to

operate. Check the local and national electrical codes

for emergency smoke removal fans.

Electrical Connections

454975

Power

Ventilator

For Smoke

Control

Systems

76Y9

–Important–

ELECTRICAL –,IIDQPRWRULV127WKHUPDOO\SURWHFWHGUHPRWH

RYHUORDGSURWHFWLRQPXVWEHLQVWDOOHGKDYLQJDGHTXDWHUDWLQJDVWR

YROWDJHIUHTXHQF\KRUVHSRZHUDQGIXOOORDGFXUUHQWSHUSKDVH

:KHUHFRQQHFWHGWRDFLUFXLWSURWHFWHGE\IXVHVXVHWLPHGHOD\IXVHV

)RUVXSSO\FRQQHFWLRQXVHZLUHVUDWHGIRUDWOHDVW&)

INSTALLATION – When connecting electrical power to this fan,

GRQRWUHVWULFWPRWRUPRYHPHQWIRUSRVVLEOHIXWXUHEHOWRUZKHHO

DGMXVWPHQW

CAUTION±0RXQWZLWKWKHORZHVWPRYLQJSDUWDWOHDVWIW

PDERYHÀRRURUJUDGHOHYHO1RWUHTXLUHGRQURRIPRXQWHG

YHQWLODWRUVRUGXFWPRXQWHGYHQWLODWRUVSURYLGHGZLWKEHOWJXDUGV

ATTENTION±0RQWHUODSLqFHPRELOHODSOXVEDVVHjDXPRLQV

PDXGHVVXVGXQLYHDXGXVRO1RQUHTXLVSRXUOHVYHQWLODWHXUV

PRQWpVVXUXQWRLWRXSRXUOHVYHQWLODWHXUVPRQWpVVXUJDLQHDYHF

SURWqJHFRXUURLH

Models TAUB with UL Emergency Smoke

Listing will bear the label shown.

Figure 1

For fan sizes 42, 48, 54 and 60, see additional

warnings related to the damper lifter on page 6.

Lifting Points

(4 places)

Tube Axial Upblast Fans6

Model TAUB (Sizes 42-60)

UL Listed Power Ventilator for Smoke Control Systems

Spring Lifter Tube

Lifter Arm

Spring Bracket

Spring

Lock Plate

Fusible Link

Assembly

Fusible Link

Assembly

Figure 2

WARNING

Disconnect and secure to the “off” position all electrical

power to the fan prior to inspection or service.

Caution must be used when working around the fusible

link damper lifters. They may release the dampers

unexpectedly.

All models may have fusible link damper lifters and all

belt drive models with high temperature options have

fusible link damper lifters under spring tension. Belt drive

fans UL Listed as “Power Ventilators For Smoke Control

Systems” in sizes 42, 48, 54 and 60 have extra heavy duty

fusible link damper lifters under high spring tension that,

for safety reasons, must be pinned to prevent accidental

release. See Figure 2 below for details on how to secure

the lifter arms.

Failure to comply with these safety precautions

may result in serious injury or death!

WARNING

These fans have extra heavy duty fusible link damper

lifters under very high spring tension that must be pinned

so they cannot be accidentally tripped when servicing the

fan. The fusible link damper lifters are located under the

butterfly damper blades.

Figure 2A shows where the two safety pins will be located

when shipped from the factory.

When maintenance is being performed on the fan, the

pins MUST be moved from Figure 2A position to Figure

2B position. Figure 2A shows where the two safety pins

are placed when the fan is in service.

Fan sizes 20, 24, 30 and 36 do not have the ability to be

pinned when servicing due to differences in lifter designs.

In all cases, extreme care must be taken when

working around the damper lifter assemblies or

serious bodily injury or death may result.

DANGER

Débrancher et verrouiller l’alimentation électrique en

position « Arrêt » avant tout contrôle ou entretien.

Faire preuve de précaution pour travailler au voisinage

des lève-registres à liaison fusible. Ils peuvent libérer les

registres de façon intempestive.

Les ventilateurs peuvent comporter des lève-registres à

liaison fusible et tous les modèles à courroie à options

haute température comportent des lève-registres à liaison

fusible sous tension de ressort. Les ventilateurs à courroie

homologués UL en tant que ventilateurs électriques pour

systèmes d’extraction de fumée dans les tailles 42, 48,

54 et 60 comportent de robustes lève-registres à liaison

fusible placés sous une forte tension de ressort qui,

pour des raison de sécurité, doivent être bloqués pour

empêcher tout déclenchement accidentel. Voir comment

fixer les bras de lève-registre à la Figure 2.

Toute infraction à ces mesures de précaution peut

entraîner des blessures graves ou la mort.

DANGER

Ces ventilateurs comportent de robustes lève-registres

à liaison fusible placés sous une très forte tension de

ressort et qui doivent être bloqués pour empêcher tout

déclenchement accidentel durant l’entretien du ventilateur.

Les lève-registres à liaison fusible sont placés sous les

clapets du registre à papillon.

La Figure 2A indique où sont placées les deux goupilles de

sécurité lors de l’expédition de l’usine.

Durant les travaux d’entretien sur le ventilateur, les

goupilles doivent IMPÉRATIVEMENT être déplacées

de leur position à la Figure 2A à celle de la Figure 2B.

La Figure 2A indique où les deux goupilles de sécurité

doivent être placées lorsque le ventilateur est en service.

Les ventilateurs de tailles 20, 24, 30 et 36 ne peuvent pas

être bloqués par une goupille durant l’entretien en raison

de différences de configuration des lève-registres.

Dans tous les cas, veiller à faire preuve d’une très

grande prudence pour travailler au voisinage des lève-

registres, en raison du danger de blessures corporelles

graves, voire de mort.

Figure 2A

Safety pin storage

location

Figure 2B

Install pin here to lockout damper lifters while servicing fan

Tube Axial Upblast Fans 7

Additional Steps for Initial Start-Up

FASTENERS - Check all fasteners and set screws for

tightness. This is especially important for bearings

and propellers. Rotate the propeller by hand to assure

it turns freely and does not rub on the fan tube. Also,

lift the butterfly dampers to check if they open and

close without binding.

PROPELLER ROTATION - Direction of propeller

rotation should be checked by turning the unit on

momentarily. Rotation should be in the same direction

shown on the rotation

decal affixed to the

unit. To reverse

rotation on three

phase installations,

simply interchange

two of the three

electrical leads.

For single phase

installations, follow

the wiring diagram

located on the motor

nameplate.

FAN RPM - For belt drive units, the adjustable

motor pulley is preset at the factory to the customer

specified RPM. Fan speed can be increased or

decreased by the adjusting the pitch diameter of the

motor pulley. Multi-groove variable pitch pulleys must

be adjusted an equal number of turns open. Always

check the motor amperage reading and compare it to

the amperage rating shown on the motor nameplate

when changing fan RPM.

Unit Start-Up

WARNING

Disconnect and secure to the OFF position all

electrical power to the fan prior to inspection

or servicing. Failure to comply with this safety

precaution could result in serious injury or death.

DANGER

Pour écarter les risques de blessure grave ou

de mort, débrancher et verrouiller l’alimentation

électrique en position « Arrêt » avant tout contrôle

ou entretien.

Visual Inspection of Equipment

The equipment type and arrangement should be

veriﬁed as ordered at once when it arrives at the

jobsite. When a discrepancy is found, the local

representative must be notiﬁed immediately so

that corrective action may be investigated. Verify

electrical conformance to speciﬁcations. Unauthorized

alterations and unauthorized backcharges will not be

recognized by manufacturer.

After the fan has been installed and all utilities have

been hooked up, the unit is ready for operation.

Check

Before starting the fan, check the following:

1. Conﬁrm that building supply voltage matches the

voltage for which the unit is wired.

2. Check all piping and wiring penetrations made by

contractors for water tightness. All penetrations

must be made watertight to prevent water

damage to the unit and building.

3. Rotate the fan propeller manually to be sure that

it is free to operate. Remove any dirt or debris

that may have accumulated during installation.

4. Check the fan bearing setscrews for tightness.

5. Check alignment of sheaves and V-belts. See

Belt Drive Maintenance section.

6. Inspect all fasteners to ensure that none have

loosened during shipment.

7. Check ﬂex coupling for proper alignment and

connect between motor shaft and fan shaft

(direct drive).

8. Check all guarding to ensure that it is securely

attached and not interfering with rotating parts.

9. Check all electrical connections for proper

attachment.

10. Check housing and ductwork, if accessible,

for obstructions and foreign material that may

damage the fan propeller.

Rotation

Actual direction of rotation

will vary by model

Electrical Connections

Before electrical connections are made, the supply

voltage, phase and ampere capacity must be checked

for compatibility with the fan motor. In addition, the

supply wiring must be properly fused and conform

to local and national electrical codes. If the unit is

supplied with a safety disconnect switch, ensure

proper wiring to the fan motor. Be sure the disconnect

is switched to the “OFF” position before connecting

supply wires. If no disconnect is supplied, ensure the

supply wire is not live before connection. Supply wires

are then connected to the optional safety disconnect

switch (if supplied) or motor.

Tube Axial Upblast Fans8

Routine Maintenance and Operation

WARNING

Disconnect and secure to the “OFF” position

all electrical power to the fan prior to inspection

or servicing. Failure to comply with this safety

precaution could result in serious injury or death.

DANGER

Pour écarter les risques de blessure grave ou

de mort, débrancher et verrouiller l’alimentation

électrique en position « Arrêt » avant tout contrôle

ou entretien.

Once the fan has been put into operation, periodic

maintenance should be scheduled to assure reliability

and performance. The following items should be

checked as a part of this maintenance schedule:

Motors

Motor maintenance is generally limited to cleaning

and lubrication. Cleaning should be limited to exterior

surfaces only. Removing dust and grease buildup

on the motor housing assists proper motor cooling.

Never wash down motor with high pressure spray.

Greasing of motors is only intended when ﬁttings are

provided. Many fractional motors are permanently

lubricated for life and require no further lubrication.

Motors supplied with grease ﬁttings should be

greased in accordance with the manufacturer’s

recommendations. When motor temperature does not

exceed 104ºF (40ºC), the grease should be replaced

after 2000 hours of running time.

Direct drive systems have extended grease lines to

lubricate the motor without removal of any guarding.

Fasteners and Set Screws

Normal fan vibration has a tendency to loosen

mechanical fasteners. Periodic inspection should

include checking all fasteners and set screws,

including the propeller fasteners, for tightness.

Direct Drive Fans

LUBRICATION - Lubrication of motors is intended

only when fittings are provided. Many fractional

horsepower motors are permanently lubricated and

require no further lubrication. Motors supplied with

grease fittings should be greased in accordance with

the manufacturers directions on the motor nameplate.

Belt Drive Fans

BEARINGS - Bearings are one of the most critical parts

of a fan and should be inspected at regular intervals.

Locking collars, set screws and fasteners attaching

the bearings to the fan should also be checked.

LUBRICATION - Bearings operating in a clean

environment and temperatures between 32°F and

200°F should be lubricated semiannually using a

high quality lithium based grease. Those operating

outside these temperatures require special high or low

temperature grease. If contamination or high moisture

conditions exist, more frequent lubrication is required.

Models TAUB-CA and TAUB are equipped with

extended lubrication lines as standard. The grease

fittings are located on the exterior of the fan housing

next to the motor cover and should be wiped clean

before adding grease.

When adding grease to the fan bearings, rotate the

fan shaft while slowly operating the manual grease

gun. Be careful not to unseat the bearing seals by

over lubricating or using excessive pressure. Stop

pumping when a very slight resistance is felt at the

grease gun.

Lubrication of motors is intended only when fittings

are provided. Many fractional horsepower motors

are permanently lubricated for life and require no

further lubrication. Motors supplied with grease

fittings should be greased in accordance with the

manufacturer’s directions on the motor nameplate.

BELTS - V-belt drives must be checked on a

regular basis for wear, tension, alignment and dirt

accumulation. Premature or frequent belt failures can

be caused by improper belt tension (either too loose

or too tight), misaligned pulleys or by prying belts on

and off pulleys. Abnormally high belt tension or drive

misalignment will cause excessive bearing loads and

may result in failure of the fan and/or motor bearings.

Conversely, loose belts will cause squealing on start-

up, excessive belt flutter, slippage and overheated

sheaves. Either excessively loose or tight belts may

cause fan vibration.

When replacing V-belts on multiple groove drives,

all belts should be changed to provide uniform drive

loading. Do not pry belts on or off the sheave. Loosen

belt tension until belts can be removed by simply

lifting the belts off the sheaves. After replacing belts,

ensure that slack in each belt is on the same side of

the drive. Belt dressing should never be used.

Fan Operation

All fans should be run every thirty (30) days, or at least

“bumped” every thirty days. It is preferred that each

fan is run as this causes all electrical and mechanical

components to get up to temperature, displacing any

formed condensation, redistributes load on bearings,

and redistributes grease in the motor and shaft

bearings.

IMPORTANT

When operating conditions of the fan are to be

changed (speed, pressure, temperature, etc.),

consult manufacturer to determine if the unit can

operate safely at the new condition.

Tube Axial Upblast Fans 9

Do not install new belts on worn sheaves. If the

sheaves have grooves worn in them, they must be

replaced before new belts are installed.

The proper tension for operating a V-belt is the lowest

tension at which the belts will not slip at peak load

conditions. Belts are adjusted by raising or lowering

the motor pivot plate. For initial tensioning, the proper

belt deflection is 1/64in. for each inch of belt span,

measured half

way between the

pulley centers.

For example, if

the belt span is

64inches, the belt

deflection should

be 1inch using

moderate thumb

pressure at mid-

point of the drive.

Check belt tension two times during the first

24hours of operation and periodically thereafter.

REMOVAL OF DUST AND DIRT - Model TAUD,

TAUB-CA and TAUB fans require very little

attention when moving clean air. If exhausting dirty

or contaminated air, the propeller and butterfly

damper assembly should be cleaned periodically.

Accumulations of dirt and debris on the propeller

blades may cause an unbalanced condition resulting

in excessive vibration and premature failure of the

propeller and bearings. Excessive buildup of dirt on

the damper blades may cause binding and sticking

blade hinges resulting in loss of fan performance.

Periodically, the motor cover on TAUB-CA and TAUB

fans should be removed and the motor cleaned of dirt

and debris. Cleaning of the motor on all fans should

be limited to the exterior. Removal of dust and dirt

from the motor will assist in motor cooling. Motors

should never be sprayed directly with water, steam or

solvents.

V-Belt Replacement

The V-belt drive components, when supplied by

Greenheck, have been carefully selected for this

unit’s speciﬁc operating condition. Changing V-belt

drive components could result in unsafe operating

conditions which may cause personal injury or failure

of fan components.

1. Remove the protective coating from the end of the

fan shaft using mineral spirits or another similar

solvent. Check to ensure that the shaft is free of

nicks and burrs.

2. Slide sheaves on shafts. Do not drive sheaves on

as this may result in bearing damage.

3. Align fan and motor sheaves with

a laser, straight-edge or string

and tighten.

4. Place belts over sheaves.

Do not pry or force

belts, as this could

result in damage to the

cords in the belts.

5. Adjust the tension until

the belts appear snug.

Run the unit for a few

minutes (refer to unit start-up section) and allow

the belts to “set” properly.

6. With the fan off, adjust the belt tension by moving

the adjustable motor plate. (Belts are adjusted

by raising or lowering the motor plate). When in

operation, the tight side of the belts should be in

a straight line from sheave to sheave with a slight

bow on the slack side.

CORRECT WRONG WRONG WRONG

Belt Span

Deﬂection =

Belt Span

Aligning Sheaves

with a Straight Edge

The adjustable motor pulley is set at the factory for

the fan RPM speciﬁed by the customer. Fan RPM can

be increased by closing or decreased by opening the

adjustable motor pulley. Multi-groove variable pitch

pulleys must be adjusted an equal number of turns

open or closed. Any increase in fan speed represents

a substantial increase in load on the motor.

To avoid motor overheating and possible burnout,

motor load amperes should always be checked and

compared to nameplate rating when fan speed is

increased.

Alignment of Pulleys and Belts

Check pulleys and belts for proper alignment to avoid

unnecessary belt wear, noise, vibration and power

loss. Motor and drive shafts must be parallel and

pulleys in line as shown.

NOTE

Model TAUB may require high temperature belts.

Tube Axial Upblast Fans10

Variable Frequency Drive

Operation

For operation with a variable frequency drive (VFD)

always check motor amps when adjusting the

operating frequency. Motor may be sized for the

original selected operating speed under 60 Hz.

Bypassing the VFD or increasing the speed from this

original selection, even if less than 60 Hz, may cause

motor to overload or fail. Consult factory with fan

serial number before increasing the upper limiting

frequency.

Always check the fan RPM when adjusting the

operating frequency. Do not exceed maximum class

fan RPM of the propeller.

NOTE

It is the responsibility of the installing body to

perform coast-down tests and identify any resonant

frequencies after the equipment is fully installed.

These resonant frequencies are to be removed

from the operating range of the fan by using the

“skip frequency” function in the VFD programming.

Failure to remove resonant frequencies from the

operating range will decrease the operating life of

the fan and void the warranty.

Field Coating Touch-Up Procedure

for Scratched Areas

Standard coating and color is RAL 7023 Concrete

Grey. This procedure outlines the correct method for

repairing minor scratches in the coating.

1. Scuff affected area to be repaired using medium

sandpaper (provided) or medium Scotch Brite™

pad. Feather the edges.

2. Clean affected area to be touched up using an

alkaline based cleaner and rinse.

3. Apply Kem Kromik

primer using 1 inch foam

brush (provided). Follow technical data sheet

instructions.

4. Allow primer to dry a minimum of 2-1/2 hours

before top coating.

5. Apply topcoat with industrial enamel using 1 inch

foam brush (provided). Follow technical data

sheets instructions. Allow painted units to air-dry

and cure before putting into service. See Technical

Data sheets (included with kit) for detailed drying

and cure schedules at different temperatures.

To order coating repair kits please reference part

number HAZ2597 PNT FIELD REPAIR KIT, RAL7023

CONCRETE GREY. Please contact factory with your

fan’s serial number for colors other than our standard.

TOUCH-UP PAINT REPAIR KIT CONTENTS

• One pint of Kem Kromik

primer

- including a technical data sheet

• One pint of industrial enamel

- including a technical data sheet

• Four disposable foam brushes

• One sheet sandpaper

• Repair procedure details

NOTE

While the manufacturer provides heavy-duty, quality

products for marine environments, routine paint

touch-ups may be required in coastal regions where

salt or marine air could damage the coating. The

severe environment will accelerate the damage from

any scratches or chips and it is recommended that

those be repaired immediately.

Tube Axial Upblast Fans 11

Parts List

CAUTION

A fan manufactured with an explosion resistant

motor does not certify the entire unit to be explosion

proof. Refer to ULListing Mark for the fans

approved usage.

Each fan bears a manufacturer’s nameplate with model number and serial number embossed. This information

will assist the local manufacturer’s representative and the factory in providing service and replacement parts.

Before taking any corrective action, make certain unit is not capable of operation during repairs.

Outlet Screen

(optional)

Propeller

Shaft Pulley

Shaft Bearings

Bearing Cover

Fan Shaft

Windband

Fusible Link Damper

Lifters (optional)

Tie Down Points

(optional)

Inspection Door

(optional)

Butterfly Dampers

Damper Hinge Rod

Windband Bracket

Motor Pulley

Belt(s)

Motor Cover

Inlet Guard

(optional)

Motor

Adjustable Motor Plate

Curb Cap

CAUTION

La présence d’un moteur antidéflagrant sur un

ventilateur ne garantit pas que tout l’appareil est

antidéflagrant. Pour connaître les emplois autorisés

de l’appareil, voir son marquage de conformité UL.

As a result of our commitment to continuous improvement, Greenheck reserves the right to change speciﬁcations

without notice.

Product warranties can be found online at Greenheck.com, either on the speciﬁc product page or in the

literature section of the website at Greenheck.com/Resources/Library/Literature.

Greenheck Tube Axial Roof Upblast catalogs provides

additional information describing the equipment, fan

performance, available accessories, and speciﬁcation data.

Phone: 715.359.6171 • Fax: 715.355.2399 • Parts: 800.355.5354 • E-mail: [email protected] • Website: www.greenheck.com

Our Commitment

AMCA Publication 410-96, Safety Practices for Users and

Installers of Industrial and Commercial Fans, provides

additional safety information. This publication can be

obtained from AMCA International, Inc. at www.amca.org.

Maintenance Log

Date _______________ Time _______________ AM/PM