Inglis IPT184301 Le manuel du propriétaire

Marque: Inglis

Modèle: IPT184301

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

TOP.MOUNT

REFRIGERATOR

In Canada, call for assistance 1-800-461-5681, for installation

and service, call: 1-800-807-6777 or visit our website at...

www.whirlpoolcanada.com

P P

REFRIGERATEUR

SUPERPOSE

Au Canada, pour assistance, composez le 1-800-461-5681, pour

installation ou service le 1-800-807-6777 ou visitez notre site web &

www.whirlpoolcanada.com

Table of Contents/Table des matieres .................. 2

2263433

TABLEOFCON[ENTS

REFRIGERATOR SAFETY ............................................................. 3

Proper Disposal of Your Old Refrigerator .................................... 3

INSTALLATION INSTRUCTIONS .................................................. 4

Unpack the Refrigerator ............................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 5

Water Supply Requirements ........................................................ 5

Connect the Water Supply ........................................................... 5

Refrigerator Doors ....................................................................... 6

Door Closing ............................................................................... 10

Normal Sounds .......................................................................... 10

REFRIGERATOR USE .................................................................. 10

Ensuring Proper Air Circulation .................................................. 10

Using the Controls ..................................................................... 11

Ice Maker .................................................................................... 11

REFRIGERATOR FEATURES ...................................................... 12

Refrigerator Shelves ................................................................... 12

Meat Drawer and Cover ............................................................. 12

Crisper and Crisper Cover ......................................................... 12

Crisper Humidity Control ........................................................... 13

Utility or Egg Bin......................................................................... 13

FREEZER FEATURES .................................................................. 13

Freezer Shelf .............................................................................. 13

DOOR FEATURES ........................................................................ 14

Drop-in Door Rails...................................................................... 14

Can Racks and Door Bins .......................................................... 14

REFRIGERATOR CARE ............................................................... 14

Cleaning ...................................................................................... 14

Changing the Light Bulbs ........................................................... 15

Power Interruptions .................................................................... 15

Vacation and Moving Care ......................................................... 15

TROUBLESHOOTING .................................................................. 16

ASSISTANCE OR SERVICE ......................................................... 17

WAR RANTY .................................................................................. 18

TABLEDESMATIERES

SI:!:CURIT¢:DU RI:!:FRIGC:RATEUR.............................................. 19

Mise au rebut de votre vieux refrig6rateur ................................. 19

INSTRUCTIONS D'INSTALLATION ............................................. 20

Deballage du refrigerateur .......................................................... 20

Emplacement d'installation ........................................................ 20

Specifications electriques .......................................................... 21

Specifications de I'alimentation en eau ..................................... 21

Raccordement de la canalisation d'eau .................................... 22

Portes du refrigerateur ............................................................... 23

Fermeture des portes ................................................................. 26

Sons normaux ............................................................................ 27

UTILISATION DU RCFRIGC:RATEUR .......................................... 27

Pour s'assurer d'une circulation d'air appropriee ...................... 27

Utilisation des commandes ........................................................ 28

Machine a gla9ons ..................................................................... 28

CARACTI:!:RISTIQUES DU RI:!:FRIGI:!:RATEUR.......................... 29

Tablettes du refrigerateur ........................................................... 29

Bac a viande et couvercle .......................................................... 29

Bac a legumes et couvercle ....................................................... 30

Reglage de I'humidite darts le bac a legumes ........................... 30

Casier utilitaire ou oeufrier .......................................................... 30

CARACTI:!:RISTIQUES DU CONGC:LATEUR ............................... 31

Clayette du congelateur ............................................................. 31

CARACTI:!:RISTIQUES DE LA PORTE ......................................... 31

Tringles dans la porte ................................................................. 31

Porte-cannettes et balconnets ................................................... 31

ENTRETIEN DU RC:FRIGI:!:RATEUR............................................ 32

Nettoyage ................................................................................... 32

Remplacement de I'ampoule d'Gclairage .................................. 32

Pannes de courant ..................................................................... 33

Entretien avant les vacances ou Iors d'un dem6nagement .......33

DI_PANNAGE ................................................................................. 33

ASSISTANCE OU SERVICE ......................................................... 35

GARANTIE ................................................................................. 36

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

• Use a sturdy glass when dispensing ice or water (on some

models).

SAVE THESE INSTRUCTIONS

ProperDisposal ofYour OldRefrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:.

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging Materials

Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

On some models, shelves, bins, door shelf rails, and other

feature parts may be packaged in the Interior FeaturePak.

Follow the instructions contained in the package for proper

assembly.

Depending on your model, to remove the protective

(transparent) film that is on the nameplate, which is located

on the freezer handle, use your fingernail and peel off the film,

starting from one side and peeling to the other.

There are 4 bolts that secure the refrigerator to the shipping

case. Keep these bolts because they are the refrigerator's

leveling legs.

• Properly dispose of packaging.

IMPORTANT: Do not remove the white foam air return insert that

is located behind the control panel on the ceiling of the

refrigerator (on some models). The insert is part of the refrigerator

and not part of the packing material. If the insert is removed, ice

may migrate down from the freezer and cause icicles to form.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pull the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

Clean Before Using

After you remove all of the package materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

"Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a 1/2"

(12.70 mm) space on each side. Allow 3" (7.5 cm) of space

between overhead cabinets and refrigerator top. Allow at least 1"

(25.40 mm) between back of cabinet and the wall. If your

refrigerator has an ice maker, make sure you leave some extra

space at the back for the water line connections.

• If you are installing your refrigerator next to a fixed wall, leave

2" (5.08 cm) minimum on the hinge side (depending on your

model) to allow for the door to swing open.

• Level the refrigerator. See "Door Closing."

NOTE:Donotinstalltherefrigeratornearanoven,radiator,or

otherheatsource,norinalocationwherethetemperaturewillfall

below55°F(13°C).

,, I lr--I

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15 or 20 amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator

or Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source

and reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

Read all directions carefully before you begin.

IMPORTANT:

• If you turn the refrigerator on before the water line is

connected, turn the ice maker OFE

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

TOOLS NEEDED: Flat-blade screwdriver, 7_6"and 1/2"open-end

wrenches or two adjustable wrenches, 1/4"nut driver and drill bit,

hand drill or electric drill (properly grounded).

NOTE: Your refrigerator dealer has a kit available with a 1/4"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3/16"

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 - 827 kPa) is required to operate the water dispenser

and ice maker. If you have questions about your water pressure,

call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 - 827 kPa)

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 - 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If you have questions about your water pressure, call a licensed,

qualified plumber.

Read all directions carefully before you begin.

IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFE

Connecting to Water Line:

Unplug refrigerator or disconnect power.

Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

Find a 1/2"(1.27 cm) to 11/4'' (3.18 cm) vertical COLD water

pipe near the refrigerator.

NOTE: Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

4. To determine the length of copper tubing you will need,

measure from connection on lower left rear of refrigerator to

water pipe. Add 7 ft (2.1 m) to allow for moving refrigerator for

cleaning. Use 1/4"(6.35 mm) O.D. (outside diameter) copper

tubing. Be sure both ends of copper tubing are cut square.

Using a grounded drill, drill a 1/4"(6.35 mm) hole in the cold

water pipe you have selected.

B ...........C

F E D v

A. Cold Water Pipe E.Compression Sleeve

B.Pipe Clamp F.Shutoff Valve

C. Copper Tubing G.Packing Nut

D. CompressionNut

6. Fasten shutoff valve to cold water pipe with pipe clamp. Be

sure outlet end is solidly in the 1/4"(6.35 mm) drilled hole in the

water pipe and that washer is under the pipe clamp. Tighten

packing nut. Tighten the pipe clamp screws carefully and

evenly so washer makes a watertight seal. Do not overtighten

or you may crush the copper tubing, especially if soft (coiled)

copper tubing is used. Now you are ready to connect the

copper tubing.

7. Slip compression sleeve and compression nut on copper

tubing as shown. Insert end of tubing into outlet end squarely

as far as it will go. Screw compression nut onto outlet end

with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing into a container or sink, and

turn ON main water supply and flush out tubing until water is

clear. Turn OFF shutoff valve on the water pipe. Coil copper

tubing.

Connecting to Refrigerator:

NOTE: The first step for connecting the water line to your

refrigerator is different depending on the type of water valve

provided with your refrigerator. See the diagrams below to

determine the style of valve you have. (On kit models, assemble

water valve to refrigerator per kit instructions.)

1. For Style 1, disconnect the tube clamp on the back of the

product and insert the copper tubing through the clamp, as

shown. Remove the tape label from the valve inlet and insert

copper tubing until it bottoms out (approximately %"

[1.9 cm]). Tighten nut by hand as much as possible; then turn

the nut an additional 1/2turn using a wrench. Do not

overtighten. Reattach the tube clamp and tube to the back of

the cabinet. Skip to Step 2.

For Style 2, disconnect the tube clamp on the back of the

product and insert copper tubing through the clamp as

shown. Attach the copper tube to the valve inlet using a

compression nut and sleeve as shown. Tighten the

compression nut. Do not overtighten. Reattach the tube

clamp and tube to the back of the cabinet. Move to Step 2.

Style I

A. Tube Clamp

B. Copper Tubing

C. Compression Nut

D. Valve Inlet

Style 2

J 1

..._O

A. Tube Clamp

B, Copper Tubing

C. Compression Nut

2. Turn shutoff valve ON. Check for leaks. Tighten any

connections (including connections at the valve) or nuts that

leak.

3. The ice maker is equipped with a built-in water strainer. If

local water conditions require periodic cleaning or a well is

your source of water supply, a second water strainer should

be installed in the 1/4"(6.35 mm) water line. Obtain a water

strainer from your nearest appliance dealer. Install at either

tube connection.

4. Plug in refrigerator or reconnect power.

TOOLS NEEDED: 5/16"hex-head socket wrench, No 2 Phillips

screwdriver, flat-head screwdriver, 5/16"open-end wrench, flat

2" putty knife.

IMPORTANT:

• Before you begin, turn the refrigerator control OFE Unplug

refrigerator or disconnect power.

• Remove food and any adjustable door or utility bins from

doors.

• If you are only removing and replacing the doors, see the

"Door and Hinge Removal" and "Door and Hinge

Replacement" sections.

Depending on your model, you may have standard (Style 1)

or contour (Style 2) doors. If you are also going to reverse the

door swing, follow the instructions for the appropriate door

style.

Door and Hinge Removal

5/16"Hex-Head Hinge Screw

Unplug refrigerator or disconnect power.

Close the refrigerator door and keep both doors closed until

you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Remove the parts for the top hinge as shown in Top Hinge

graphic.

4. Lift the freezer door free from the cabinet.

5. Remove the parts for the center hinge as shown in the Center

Hinge graphic.

6. Lift the refrigerator door free from the cabinet.

7. Removethepartsforthebottomhingeasshowninthe

BottomHingegraphic.

IMPORTANT:Ifyouwanttoreverseyourdoorssothattheyopen

intheoppositedirection,followthesesteps.Ifyouarenot

reversingthedoors,see"DoorandHingeReplacement."

Door Reversal (optional)

Style I - Standard

(Graphics follow these instructions.)

Door StopScrew

Door HandleSealing Screw

Flat-Head Handle Screw

Door Handle Seal Screw Front

DoorHinge Hole Plug

Cabinet Hinge Hole Plug

Door Handle Screw Cover

Round-Head Handle Screw

Cabinet

1. Remove %6" hex-head hinge screws from handle side and

move them to opposite side. See Graphic 1-1.

2. Remove cabinet hinge hole plugs from cabinet top and

move them to opposite side hinge holes as shown.

See Graphic 1-2.

Freezer door

1. Remove freezer handle assembly as shown. Keep all parts

together. See Graphic 2.

2. Remove door hinge hole plug. Move to opposite side as

shown. See Graphic 3.

3. Remove door handle sealing screws. Move to opposite side

of freezer door as shown. See Graphic 4.

4. Remove door stop. Move to opposite side of freezer door as

shown. See Graphic 5.

5. Position freezer handle on opposite side of freezer door.

Assemble handle on door as shown. See Graphic 2.

6. Tighten all screws. Set aside door until hinges and

refrigerator compartment door are in place.

Refrigerator door

1. Remove the screw cover. See Graphic 6.

2. Remove refrigerator handle assembly as shown. Keep all

parts together. See Graphic 6.

3. Remove door hinge hole plug from refrigerator door. Move to

opposite side hinge hole as shown. See Graphic 3.

4. Remove door handle sealing screws. Move to opposite side

of refrigerator door as shown. See Graphic 4.

5. Remove door handle seal screw front. Move to opposite side

of refrigerator door as shown. See Graphic 7.

6. Remove door stop. Move to opposite side of refrigerator door

as shown. See Graphic 5.

7. Position refrigerator handle on opposite side of the

refrigerator door as shown. See Graphic 6. Drive top two

screws in handle first. Align lower portion of handle and drive

bottom screw.

8. Replace screw cover. See Graphic 6.

9. Tighten all screws. Set aside refrigerator door until bottom

hinge is installed on refrigerator.

Style 2 - Contour

(Graphicsfollow these instructions.)

Round-Head Door Handle

Handle Screw Screw Hole Plug

Cabinet

Door Hinge

Hole Plug

NOTE: Graphic may be reversed if door swing is reversed.

1. Replace the parts for the bottom hinge as shown. Tighten

screws. Replace the refrigerator door.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

2. Assemble the parts for the center hinge as shown and tighten

all screws. See Center Hinge graphic. Replace the freezer

door.

3. Assemble the parts for the top hinge as shown. See Top

Hinge graphic. Do not tighten screws completely.

4. Line up the doors so that the bottom of the freezer door

aligns evenly with the top of the refrigerator door. Tighten all

screws.

Final Steps

1. Check all holes to make sure that hole plugs and screws are

in place. Reinstall top hinge cover. See Top Hinge graphic.

2. Plug in refrigerator or reconnect power.

3. Reset the controls. See "Using the Control(s)" section,

depending on your model.

4. Return all removable door parts to doors and food to

refrigerator.

1. Remove 5/16"hex-head hinge screws from handle side and

move them to opposite side. See Graphic 1-1.

2. Remove cabinet hinge hole plugs from the cabinet top and

move them to opposite side hinge holes as shown. See

Graphic 1-2.

Doors

1. Remove door hinge hole plug from top of freezer door. Move

to opposite side as shown. See Graphic 2.

2. Remove door stop from both the freezer and refrigerator

doors and move to the other side. See Graphic 3.

Door and Hinge Replacement

Style I - Standard

Top Hinge

A. 5/_8"Hex-Head Hinge Screws

B. Top Hinge

C. Spacer

Center Hinge

C ...............

A. Door Stop

B. Door Stop Screw

C. Spacer

D. Center Hinge

E. 5A6"Hex-Head Hinge Screws

K Spacer

Bottom Hinge

iiiiiiiiiiiiiiiiiE

iiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiii A. Door Stop

iiiiiiiiiiiiiiiii B. Spacer

iiiiiiiiiiiiiiiii C. Door Stop Screw

iiiiiiiiiiiiiiiii D. BottomHinge

iiiiiiiiiiiiiiiiiE J, 'HexHeadHingeScrews

A. Cabinet Hinge Hole Plugs

A. Door Hinge Hole Plug

A. Flat-Head Handle Screws

B. Freezer Handle

A. Door Handle Sealing Screws

Front View Side View

A. Door Stop Screw A B

B. Door Stop

o.i? _ o,

A. 5h_"Hex-Head Hinge

Screws and Washers

A. Door Handle

Seal Screw Front

Style 2 - Contour

Top Hinge

A. Top Hinge Cover

B. %J Hex-Head Hinge Screws

C. Top Hinge

D. Spacer

Center Hinge

A. Door Stop

B. Door Stop Screw

C. Spacer

D. Center Hinge

E. 5A6"Hex-Head Hinge Screws

K Spacer

Bottom Hinge

A. Door Stop

B. Spacer

C. Door Stop Screw

D. Bottom Hinge

E. b/_,, Hex-Head Hinge Screws

[]

A. Cabinet Hinge Hole Plugs

A. Door Hinge Hole Plug

Removal of Door Stops

A. Door Stop

B. Door Stop Screw

Reinstallation of Door Stops

A. Door Step

B. Door Stop Screw

Your refrigerator has two front adjustable rollers - one on the right

and one on the left. Ifyour refrigerator seems unsteady or you

want the doors to close easier, adjust the refrigerator's tilt using

the instructions below:

Roll out the refrigerator and use a level to check the floor at

the back from side to side. If needed, use shims to level the

back of the refrigerator if it is uneven. Roll the refrigerator

back into place with the rear rollers on top of any shim(s)

used so that the rear of the refrigerator is level.

With the rear already level and the refrigerator in place, use

the bottom leveling screws to level the refrigerator from side

to side. They are part of the front roller assemblies, which are

found at the base of the refrigerator on either side.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws and

rollers. This makes it easier to adjust the screws.

Depending on your model, to level your refrigerator you may

either turn the screw clockwise to raise that side of the

refrigerator or turn the screw counterclockwise to lower that

side. Place a level on top of the refrigerator to check

adjustments.

Style I

Style 2

Your new refrigerator may make sounds that your old one didn't

make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard

surfaces, such as the floor, walls, and cabinets, can make the

sounds seem louder. The following describes the kinds of sounds

and what may be making them.

• If your product is equipped with an ice maker, you will hear a

buzzing sound when the water valve opens to fill the ice

maker for each cycle.

Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperatures and to minimize

energy usage. The high efficiency compressor and fans may

cause your refrigerator to run longer than your old one. You

may also hear a pulsating or high-pitched sound from the

compressor or fans adjusting to optimize performance.

You may hear the evaporator fan motor circulating air through

the refrigerator and freezer compartments. The fan speed

may increase as you open the doors or add warm food.

Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.

As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your refrigerator.

Contraction and expansion of the inside walls may cause a

popping noise.

You may hear air being forced over the condenser by the

condenser fan.

You may hear water running into the drain pan during the

defrost cycle.

REFRIGERATORUSE

In order to ensure proper temperatures, you need to permit

airflow between the refrigerator and freezer sections. As shown in

the illustration, cool air enters through the bottom of the freezer

section and moves up. Most of the air then flows through the

freezer section vents and recirculates under the freezer floor. The

rest of the air enters the refrigerator section through the top vent.

In some models, cool air enters through the backwall of

refrigerator section and moves to the front of the refrigerator and

up into the freezer.

If the doors do not close on their own, you will need to raise

the front of the refrigerator so it is slightly higher than the

back. To do this, turn both leveling screws clockwise 1/2turn.

IMPORTANT: Be sure to turn both screws an equal amount

or the refrigerator will no longer be level side to side.

5. Open both doors again and check to make sure that they

close as easily as you like. If not, repeat steps 3 and 4.

6. Using a level, check to see that the refrigerator is still level

side to side. Readjust if necessary.

Do not block any of these vents with food packages. If the vents

are blocked, airflow will be prevented and temperature and

moisture problems may occur.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent

odor transfer and drying out of food, wrap or cover foods tightly.

See the "Refrigerator Features" section for details.

For your convenience, your refrigerator controls are preset at the

factory. When you first install your refrigerator, make sure that the

controls are still preset to the mid-settings as shown.

NOTE: To turn your refrigerator off, turn the refrigerator control to

the word OFF or until the word OFF appears. Your product will

not cool when the refrigerator control is set to OFR

Mid-setting "3"

OFF

COLDES0

5 1

NORMAL

IMPORTANT:

Give your refrigerator time to cool down completely before

adding food. It is best to wait 24 hours before you put food

into the refrigerator.

If you add food before the refrigerator has cooled completely,

your food may spoil. Adjusting the Refrigerator and Freezer

Controls to a higher (colder) than recommended setting will

not cool the compartments any faster.

Adjusting Controls

The mid-settings indicated in the previous section should be

correct for normal household usage. The controls are set

correctly when milk or juice is as cold as you like and when ice

cream is firm.

If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not blocked.

If you need to adjust temperatures, use the settings listed in the

chart below as a guide. On models with two controls, adjust the

refrigerator temperature first. Wait at least 24 hours between

adjustments and then recheck the temperatures.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR section too warm Adjust REFRIGERATOR

- Door opened often, large amount or TEMPERATURE

of food added or room Control one setting

temperature very warm higher

FREEZER section too warm/ice

not made fast enough

- Door opened often, or large

amount of food added or very cold

room temperature (can't cycle

often enough)

- Heavy ice usage

Adjust FREEZER or

TEMPERATURE Control

one setting higher

REFRIGERATOR section too cold

- Controls not set correctly for

your conditions

Adjust REFRIGERATOR

or TEMPERATURE

Control one setting

lower

FREEZER section too cold

- Controls not set correctly for

your conditions

Adjust FREEZER or

TEMPERATURE Control

one setting lower

Turning the Ice Maker On/Off

NOTE: Do not force the wire shutoff arm up or down.

• To turn the ice maker on, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice

cubes will raise the wire shutoff arm to the OFF (arm up)

position.

To manually turn the ice maker off, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click to make sure

the ice maker will not continue to operate.

Ice Production Rate

NORMAL Ice Production: In Normal ice production mode, the

ice maker should produce approximately 8 to 12 batches of

ice in a 24-hour period. If ice is not being made fast enough,

turn the Freezer Control toward a higher (colder) number in

half number steps. (For example, if the control is at 3, move it

to between 3 and 4.) Wait 24 hours and, if necessary,

gradually turn the Freezer Control to the highest setting,

waiting 24 hours between each increase.

MAXIMUM Ice Production (on some models): In Maximum ice

production, the ice maker should produce approximately

16 to 20 batches of ice in a 24-hour period. If your refrigerator

has the maximum ice production feature, push the switch to

MAX.

Remember

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

The quality of your ice will be only as good as the quality of

the water supplied to your ice maker. Avoid connecting the

ice maker to a softened water supply. Water softener

chemicals (such as salt) can damage parts of the ice maker

and lead to poor quality ice. If a softened water supply cannot

be avoided, make sure the water softener is operating

properly and is well maintained.

• Do not store anything on top of the ice maker or in the ice

storage bin.

REFRIGERATORFEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

See the "Assistance or Service" section if you are interested in

purchasing one of the accessories.

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

The shelves in your refrigerator are adjustable to match your

individual storage needs.

Storing similar food items together in your refrigerator and

adjusting the shelves to fit different heights of items will make

finding the exact item you want easier. It will also reduce the

amount of time the refrigerator door is open, and save energy.

Remove and replace a shelf:

1. Remove items from the shelf.

2. Slide the shelf straight out to the stop.

3. Depending on your model, lift back or front of the shelf past

the stop. Slide shelf out the rest of the way.

4. Replace the shelf by sliding the back of the shelf into the

track in the wall of the cabinet.

5. Guide the front of the shelf into the shelf track. Be sure to

slide the shelf in all the way.

Remove and replace the meat drawer:

1. Slide meat drawer out to the stop.

2. Lift front of meat drawer with one hand while supporting

bottom of drawer with other hand. Slide drawer out the rest of

the way.

3. Replace the drawer by sliding it back in fully past the drawer

stop.

Remove and replace the meat drawer cover

(Glass meat drawer cover on some models):

1. Remove the meat drawer.

2. Push the cover back to release the rear clips from the shelf.

Tilt the cover up at the front, and pull it forward.

3. Replace the meat drawer cover by fitting the notches and

clips on the cover over the rear and center crossbars on the

shelf.

4. Lower cover into place and pull the cover forward to secure

the rear clips onto the shelf.

5. Replace the meat drawer.

NOTE: In some models the meat pan moves sideways on the

shelf to allow for flexible positioning.

Meat storage guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish ......................... use same day as purchased

Chicken, ground beef, variety meats (liver) ...................... 1-2 days

Cold cuts, steaks/roasts .................................................. 3-5 days

Cured meats ................................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

Remove and replace the crisper(s):

1. Slide crisper(s) straight out to the stop. Lift the front and slide

the crisper(s) out the rest of the way.

2. Replace the crisper(s) by sliding the crisper(s) in fully past the

stop.

Style I - Remove and replace the plastic cover

(Glass insert on some models)

1. Remove the crisper(s).

2. Lift the front of the cover to remove the cover support. Then

lift the cover up and slide it out.

• Vegetables with skins: Place in plastic bag or plastic

container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or tear

off bruised and discolored areas. Place in plastic bag or

plastic container and store in crisper.

3. Replace the cover by fitting the cover tabs into lowest cabinet

slots and pushing them in. Lower the front retainers into

place.

4. Insert cover support (with the long tab toward the front) into

the groove on the underside of the cover.

NOTE: If the support needs adjustment, turn base clockwise

to raise or counterclockwise to lower.

Style 2 - Remove and replace the glass cover:

1. Pull the glass straight out.

2. Replace the glass by pushing it straight in.

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and

HIGH.

\ Humidity Control

LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

• Fruit: Wash, let dry and store in refrigerator in plastic bag or

crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper, or store

in a loosely closed paper bag on a refrigerator shelf.

Depending on your model, you may have a one, two or three

piece bin. Eggs may be stored in the egg tray or loose in the bin.

NOTE: Store eggs in a covered container for long-term storage. If

your model does not have an egg storage bin, store eggs in their

original container on an interior shelf.

FREEZER FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

See the "Assistance or Service" section if you are interested in

)urchasing one of the accessories.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

Remove and replace the freezer shelf

1. Remove items from the shelf.

2. Lift back of shelf over stop and slide shelf straight out.

3. Replace the shelf by sliding the back of the shelf into the

tracks on walls of cabinet.

4. Be sure to slide the shelf in all the way.

Frozenfoodstorageguide

Storage times will vary according to the quality and type of food,

the type of packaging or wrap used (should be airtight and

moisture-proof), and the storage temperature. Seal the package

or container securely to prevent taste and odor transfer

throughout the product. Ice crystals inside a sealed package are

normal. This simply means that moisture in the food and air

inside the package have condensed, creating ice crystals.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2-3 Ibs of food per cubic foot [907-

1,350 g per L] of freezer space). Leave enough space in the

freezer for air to circulate around packages. Be careful to leave

enough room for the door to close tightly.

NOTE: For more information on preparing food for freezing,

check afreezer guide or reliable cookbook.

DOORFEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

See the "Assistance or Service" section if you are interested in

purchasing one of the accessories.

The door rails may be removed for easier cleaning.

Remove and replace the rails

1. Remove all items from the shelf and pull straight up on each

end of the rails.

2. Locate each end of the rail above the rail's pocket opening,

and push the rail straight down until it stops.

NOTE: Can racks may be purchased as an Accessory for some

models.

Remove and replace the racks/bins

1. Remove the racWbin by lifting it and pulling it straight out.

2. Replace the racWbin by sliding it in above the desired

support and pushing it down until it stops.

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

Cleaning your refrigerator

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves,

crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning

waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts, interior

and door liners or gaskets. Do not use paper towels,

scouring pads, or other harsh cleaning tools. These can

scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs. to 1 qt.

[26 g to 0.95 L] of water).

4. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water. Do

not use abrasive or harsh cleaners. Dry thoroughly with a soft

cloth. For additional protection against damage to painted

metal exteriors, apply appliance wax (or auto paste wax) with

a clean, soft cloth. Do not wax plastic parts.

NOTE: To keep your stainless steel refrigerator looking like

new and to remove minor scuffs or marks, it is suggested that

you use the manufacturer's approved Stainless Steel Cleaner

& Polish.

IMPORTANT: This cleaner is for stainless steel parts only!

Do not allow the Stainless Steel Cleaner & Polish to come into

contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If accidental contact does

occur, clean plastic part with a sponge and mild detergent in

warm water. Dry thoroughly with a soft cloth. To order the

cleaner, see the "Accessories" section.

Clean the condenser coils regularly. Coils may need to be

cleaned as often as every other month. This may help save

energy.

• Pull refrigerator out away from the wall. See "Unpacking

the Refrigerator."

• Vacuum coils when they are dusty or dirty.

• Roll refrigerator back into place. Make sure to leave 1"

(2.5 cm) between the cabinet back and the wall.

• Check to see that the refrigerator is level.

Plug in refrigerator or reconnect power.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with one of the same size, shape, and wattage.

Refrigerator Light

1. Unplug refrigerator or disconnect power.

2. Reach behind the control panel and unscrew the bulb.

3. Replace the bulb with a 40-watt appliance bulb.

4. Plug in refrigerator or reconnect power.

Freezer Light (on some models)

1. Unplug refrigerator or disconnect power.

2. Remove the freezer shelf.

3. Remove the freezer light shield by pushing down.

4. Remove the light bulb and replace with one of the same size,

shape and wattage.

5. Replace the light shield.

6. Plug in refrigerator or reconnect power.

If the power will be out for 24 hours or less, keep the door or

doors closed (depending on your model) to help food stay cold

and frozen.

If the power will be out for more than 24 hours, do one of the

following:

• Remove all frozen food and store it in a frozen food locker.

• Place 2 Ibs (907 g) of dry ice in the freezer for every cubic foot

(28 L) of freezer space. This will keep the food frozen for 2 to

4 days.

• If neither a food locker nor dry ice is available, consume or

can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled

one. A freezer full of meat stays cold longer than a freezer full of

baked goods. If you see that food contains ice crystals, it may be

refrozen, although the quality and flavor may be affected. If the

condition of the food is poor, dispose of it.

Vacations

If You Choose to Leave the Refrigerator On While You're

Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Raise wire shutoff arm to OFF (up) position or move the

switch to the OFF (right) setting.

• Shut off water supply to the ice maker.

3. Empty the ice bin.

If You Choose to Turn the Refrigerator Off Before You

Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

3. Depending on the model, turn the Thermostat Control or

Refrigerator Control to OFR See "Using the Controls."

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• Disconnect the water line from the back of the

refrigerator.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Depending on the model, turn the Thermostat Control or

Refrigerator Control to OFR See "Using the Controls."

5. Unplug refrigerator.

6. Empty water from the defrost pan.

7. Clean, wipe, and dry thoroughly.

8. Take out all removable parts, wrap them well, and tape them

together so they don't shift and rattle during the move.

9. Depending on the model, raise the front of the refrigerator so

it rolls more easily OR screw in the leveling legs so they don't

scrape the floor. See "Adjust the Doors."

10. Tape the doors closed and tape the power cord to the

refrigerator cabinet.

When you get to your new home, put everything back and refer to

the "Installation Instructions" section for preparation instructions.

Also, if your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

TROUBLESHOOTING

Trythe solutions suggested here first in order to avoid the cost of an unnecessary service call.

Your refrigerator will not operate

• Is the power supply cord unplugged? Plug into a grounded

3 prong outlet.

Has a household fuse blown or circuit breaker tripped?

Replace the fuse or reset the circuit.

Is the Refrigerator Control turned to the OFF position?

See "Using the Control(s)," depending on the model.

msthe refrigerator defrosting? Recheck to see whether the

refrigerator is operating in 30 minutes. Your refrigerator will

regularly run an automatic defrost cycle.

The lights do not work

• is the power supply cord unplugged? Plug into a grounded

3 prong outlet.

msa light bulb loose in the socket? Turn the refrigerator

control to OFE Disconnect the refrigerator from the electrical

supply. Gently remove the bulb and reinsert. Then reconnect •

the refrigerator to the electrical supply and reset the

refrigerator control. •

• Has a light bulb burned out? Replace with an appliance

bulb of the same wattage, size, and shape. See "Changing

the Light Bulb(s)," depending on the model

There is water in the defrost drain pan

• is the refrigerator defrosting? The water will evaporate. It is

normal for water to drip into the defrost pan.

• Is it more humid than normal? Expect that the water in the

defrost pan will take longer to evaporate. This is normal when

it is hot or humid.

The motor seems to runtoo much

Is the room temperature hotter than normal? Expect the

motor to run longer under warm conditions. At normal room

temperatures, expect your motor to run about 40% to 80% of

the time. Under warmer conditions, expect it to run even

more of the time.

Has a large amount of food just been added to the

refrigerator? Adding a large amount of food warms the

refrigerator. It is normal for the motor to run longer in order to

cool the refrigerator back down. See "Refrigerator Features."

Are the doors opened often? Expect the motor to run longer

when this occurs. In order to conserve energy, try to get

everything you need out of the refrigerator at once, keep food

organized so it is easy to find, and close the door as soon as

the food is removed.

Is the control set correctly for the surrounding

conditions? See "Using the Control(s)," depending on the

model.

Are the doors closed completely? Push the doors firmly

shut. Ifthey will not shut all the way. See "The doors will not

close completely" later in this section.

Are the condenser coils dirty? This prevents air transfer and

makes the motor work harder. Clean the condenser coils. See

"Cleaning."

NOTE: Your new refrigerator will run longer than your old one due

to its high-efficiency motor.

The refrigerator seems to make too much noise

• The sounds may be normal for your refrigerator. See

"Normal Sounds."

The ice maker is not producing ice (on some models)

• Is the freezer temperature cold enough to produce ice?

Wait 24 hours after hookup for ice production. See "Using the

Control(s)," depending on the model.

Is the wire shutoff arm in the OFF (arm up) position?

Lower the wire shutoff arm to the ON (arm down) position.

See "Ice Maker."

Is the water line shutoff valve to the refrigerator turned

on? Turn on the water valve. See "Connect the Water

Supply."

Is an ice cube jammed in the ejector arm? Remove the ice

from the ejector arm with a plastic utensil. See "Ice Maker."

Does the ice maker mold have water in it or has no ice

been produced? Check to see that your refrigerator has

been connected to your home water supply and the supply

shutoff valve is turned on. See "Connect the Water Supply."

NOTE: If not due to any of the above, there may be a problem

with the water line. Call for service.

The ice maker is producing too little ice (on some

models)

Has the ice maker just been installed? Wait 72 hours for full

ice production to begin. Once your refrigerator is cooled

down, the ice maker should begin producing 70 to 120 cubes

every 24 hours.

• Has a large amount of ice just been removed? Allow

24 hours for ice maker to produce more ice.

• Is the control set correctly? See "Using the Control(s),"

depending on the model.

• is the water shutoff valve turned completely on? Turn

valve on fully. See "Connect the Water Supply."

Is there a water filter installed on the refrigerator? This

filter may be clogged or installed incorrectly. First, check the

filter installation instructions to ensure that the filter was

installed correctly and is not clogged. If installation or

clogging is not a problem, call a technician or other qualified

person.

• msa reverse osmosis water filtration system connected to

your cold water supply? See "Water Supply Requirements."

Off-taste or gray color in the ice (on some models)

• Are the plumbing connections new, causing discolored or

off-flavored ice? Discard the first few batches of ice.

• Have the ice cubes been stored for too long? Throw away

old ice and make a new supply.

• Has food in the refrigerator been wrapped properly? See

"Refrigerator Features."

• Do the freezer and ice bin need to be cleaned? See

"Cleaning."

• Does the water contain minerals (such as sulfur)? A filter

may need to be installed to remove the minerals.

The divider between the two compartments iswarm

The warmth is probably due to normal operation of the automatic

exterior moisture control. If still concerned, call for service.

Temperature is too warm

Are the air vents blocked in either compartment? This

prevents the movement of cold air from the freezer to the

refrigerator. Remove any objects from in front of the air vents.

See "Ensuring Proper Air Circulation" for the location of air

vents.

Are the door(s) opened often? Be aware that the refrigerator

will warm when this occurs. In order to keep the refrigerator

cool, try to get everything you need out of the refrigerator at

once, keep food organized so it is easy to find, and close the

door as soon as the food is removed.

Has a large amount of food just been added to the

refrigerator or freezer? Adding a large amount of food

warms the refrigerator. It can take several hours for the

refrigerator to return to the normal temperature.

Are the controls set correctly for the surrounding

conditions? See "Using the Control(s)," depending on the

model.

There is interior moisture buildup

• Are the air vents blocked in the refrigerator? Remove any

objects from in front of the air vents. See "Ensuring Proper Air

Circulation" for the location of air vents.

Are the door(s) opened often? To avoid humidity buildup,

try to get everything you need out of the refrigerator at once

keep food organized so it is easy to find, and close the door

as soon as the food is removed. When the door is opened,

humidity from the room air enters the refrigerator. The more

often the door is opened, the faster humidity builds up,

especially when the room itself is very humid.

Is the room humid? It is normal for moisture to build up

inside the refrigerator when the room air is humid.

Is the food packaged correctly? Check that all food is

securely wrapped. Wipe off damp food containers before

placing in the refrigerator.

Are the controls set correctly for the surrounding

conditions? See "Using the Control(s)," depending on the

model.

Was a self-defrost cycle completed? It is normal for

droplets to form on the back wall after the refrigerator self-

defrosts.

The doors are difficultto open

• Are the gaskets dirty or sticky? Clean gaskets and the

surface that they touch. Rub a thin coat of paraffin wax on the

gaskets following cleaning.

The doors will not close completely

• Are food packages blocking the door open? Rearrange

containers so that they fit more tightly and take up less

space.

Is the ice bin out of position? Push the ice bin in all the way.

Are the crisper cover, pans, shelves, bins, or baskets out

of position? Put the crisper cover and all pans, shelves, bins,

and baskets back into their correct positions. See

"Refrigerator Features."

Are the gaskets sticking? Clean gaskets and the surface

that they touch. Rub a thin coat of paraffin wax on the

gaskets following cleaning.

Does the refrigerator wobble or seem unstable? Level the

refrigerator. See "Door Closing."

Were the doors removed during product installation and

not properly replaced? Remove and replace the doors

according to "Refrigerator Doors," or call a qualified service

technician.

ASSISTANCEORSERVICE

Before calling for assistance or service, please check

"Troubleshooting." It may save you the cost of a service call. If

you still need help, follow the instructions below.

When calling, please know the purchase date and the complete

model and serial number of your appliance. This information will

help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

only use factory specified replacement parts. Factory specified

replacement parts will fit right and work right, because they are

made with the same precision used to build every new INGLIS ®

appliance.

To locate factory specified replacement parts in your area, call

our Customer Interaction Center telephone number or your

nearest designated service center.

Call the Whirlpool Canada Inc. Customer Interaction Center toll

free: 1-800-481-5681 Monday to Friday 8:00 a.m. - 6:00 p.m.

(EST). Saturday 8:30 a.m. - 4:30 p.m. (EST).

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Referrals to local dealers.

For service in Canada

Call 1-800-807-6777. Whirlpool Canada Inc. designated service

technicians are trained to fulfill the product warranty and provide

after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to Whirlpool Canada

Inc. with any questions or concerns at:

Whirlpool Canada Inc.

Customer Interaction Center

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

INGLIS®REFRIGERATORWARRANTY

ONE-YEAR FULL WARRANTY ON REFRIGERATOR

For one year from the date of purchase, when this refrigerator (excluding the water filter) is operated and maintained according to

instructions attached to or furnished with the product, Whirlpool Canada Inc. will pay for replacement parts and repair labor costs to

correct defects in materials or workmanship. Service must be provided by a Whirlpool Canada Inc. designated service company.

On models with a water filter: 30 day limited warranty on water filter. For 30 days from the date of purchase, when this filter is operated

and maintained according to instructions attached to or furnished with the product, Whirlpool Canada Inc. will pay for replacement

parts to correct defects in materials and workmanship.

SECOND THROUGH FIFTH YEAR FULL WARRANTY ON SEALED REFRIGERATION SYSTEM PARTS AS LISTED

In the second through fifth years from the date of purchase, when this refrigerator is operated and maintained according to instructions

attached to or furnished with the product, Whirlpool Canada Inc. will pay for replacement parts and repair labor costs to correct defects

in materials or workmanship in the sealed refrigeration system. These parts are: compressor, evaporator, condenser, dryer, and

connecting tubing. Service must be provided by a Whirlpool Canada Inc. designated service company.

Whirlpool Canada Inc. will not pay for:

1. Service calls to correct the installation of your refrigerator, to instruct you how to use your refrigerator, to replace house fuses or

correct house wiring or plumbing, to replace light bulbs, or for replacement water filters other than as noted above.

2. Repairs when your refrigerator is used in other than normal, single-family household use.

3. Pickup and delivery. Your refrigerator is designed to be repaired in the home.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, improper installation, acts of God, or use of products not

approved by Whirlpool Canada Inc.

5. Any food loss due to product failure.

6. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

7. Replacement parts or repair labor costs for units operated outside Canada.

8. Travel or transportation expenses for customers who reside in remote areas.

WHIRLPOOL CANADA INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some provinces do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation may not

apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from province to province.

Outside Canada, this warranty does not apply. Contact your authorized Whirlpool Canada Inc. dealer to determine if another

warranty applies.

If you need service, first see the "Troubleshooting" section of this book. After checking "Troubleshooting," additional help can be found

by checking the "Assistance or Service" section or contact your Whirlpool Canada Inc. designated service company or call

1-800-807-6777. 8/02

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your refrigerator to

better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the inside wall of the refrigerator

compartment.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

SECURITEDURl FRIGERATEUR

Votre s6curit6 et celle des autres est tres importante.

Nous donnons de nombreux messages de s6curite importants dans ce manuel et sur votre appareil menager. Assurez-vous de

toujours lire tous les messages de securite et de vous y conformer.

Voici le symbole d'alerte de securite.

Ce symbole d'alerte de securite vous signale les dangers potentiels de deces et de blessures graves & vous

eta d'autres.

Tousles messages de securite suivront le symbele d'alerte de securit6 et le mot "DANGER" ou

"AVERTISSEMENT". Ces roots signifient :

Risque possible de deces ou de blessure grave si vous ne

suivez pas immediatement lee instructions.

Risque possible de deces ou de blessure grave si vous

ne euivez pas lee instructions.

Tousles messages de securite vous diront quel est le danger potentiel et vous disent comment reduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

IMPORTANTES iNSTRUCTiONS DE S#:CURITE

AVERTISSEMENT : Pour reduire les risques d'incendie, de choc electrique ou des blessures lots de I'utilisation du

refrigerateur, prendre quelques precautions fondamentales, y compris les suivantes •

• Brancher I'appareil sur une prise & 3 alveoles reliee & la terre.

• Ne pas enlever la broche de liaison a la terre.

• Ne pas utiliser un adaptateur.

• Ne pas utiliser un c&ble de rallonge.

• Utiliser deux ou plus de personnes pour deplacer et installer

le refrig6rateur.

• Debrancher la source de courant electrique avant I'entretien.

• Replacer tousles panneaux avant de faire la remise en

marche.

• Utiliser un produit de nettoyage ininflammable.

• Garder les mat@iaux et les vapeurs inflammables, telle que

I'essence, loin du refrig@ateur.

• Debrancher le refrig6rateur avant I'installation de la machine

& glagons (seulement pour modeles pr6ts a recevoir une

machine a glagons).

• Utiliser un verre robuste pour prendre des gla(_ons ou de

I'eau (sur certains modeles).

• Enlever les portes de votre vieux refrig@ateur.

CONSERVEZ CES iNSTRUCTiONS

Mise au rebut de votre vieux r frig6rateur

Risque de suffoquer

Enlever lee portee de votre vieu× refrigerateur.

Le non-respect de cette instruction peut causer

un deces ou des lesions cerebrales.

Avant de jeter votre vieux r6frig6rateur ou cong61ateur :

Enlever les portes.

Laisser les tablettes en place de sorte que les enfants ne

peuvent pas y penetrer facilement.

IMPORTANT : L'emprisonnement et I'etouffement des enfants ne

sont pas un probleme du passe. Les refrig@ateurs jetes eu

abandennes sent encore dangereux, m6me s'ils sent laisses

abandennes pendant "quelques jours seulement". Si veus vous

debarrassez de votre vieux refrigerateur, veuillez suivre les

instructions suivantes pour aider a eviter les accidents.

INSTRUCTIONSD'INSTALLATION

Risque du poids excessif

Utiliser deux ou plus de personnes pour d_placer et

installer le r_frigerateur.

Le non-respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

Enl_vement des mat_riaux d'emballage

Enlever le ruban adhesif et la colle des surfaces du

refrig@ateur avant de le mettre en marche. Frotter une petite

quantite de savon liquide pour la vaisselle sur I'adhesif avec

les doigts. Rincer h I'eau tiede et essuyer.

Ne pas utiliser d'instruments coupants, d'alcool afriction, de

liquides inflammables ou de nettoyants abrasifs pour enlever

le ruban adh_sif ou la colle. Ces produits peuvent

endommager la surface de votre refrig6rateur. Pour plus de

renseignements, voir "Securite du refrig@ateur".

Sur certains modeles, des tablettes, bacs, glissieres de

tablettes dans la porte et autres pieces peuvent _tre emballes

dans la trousse FeaturePak. Suivre les instructions contenues

dans I'emballage pour le montage approprie.

Selon le modele que vous avez, pour enlever la pellicule

protectrice (transparente) qui recouvre la plaque signaletique

situee sur la poignee du congelateur, utiliser votre ongle,

enlever la pellicule en la decollant d'un c6te a I'autre.

• II y a 4 boulons qui arriment le refrigerateur h la boite

d'expedition. Conserver ces boulons; ils servent de pieds de

nivellement pour le refrig@ateur.

• 121iminerles materiaux d'emballage de la maniere appropriee.

IMPORTANT: Ne pas enlever I'encart en mousse blanche du

retour d'air situe derriere le panneau de reglage au plafond du

rdrigerateur (sur certains modeles). L'encart fait partie du

refrig6rateur et n'est pas un materiau d'emballage. Si I'encart est

enleve, de la glace peut se former en provenance du congelateur

et causer la formation de glagons.

D_placement de votre refrig_rateur :

Votre refrig6rateur est Iourd. Lots du d@lacement du

refrig@ateur pour le nettoyage ou le service, veiller & proteger

le plancher. Toujours tirer le refrig@ateur tout droit lots du

deplacement. Ne pas incliner le refrig@ateur d'un c6te ou de

I'autre nile "faire marcher" en essayant de le d@lacer car le

plancher pourrait 6tre endommage.

Nettoyage avant rutilisation

Apres avoir enleve tousles materiaux d'emballage, nettoyer

I'interieur du refrigerateur avant de I'utiliser. Voir les instructions

de nettoyage dans "Entretien du refrigerateur".

Importants renseignements a savoir au sujet des tablettes

et des couvercles en verre :

Ne pas nettoyer les tablettes ou couvercles en verre avec de

I'eau tiede quand ils sent froids. Les tablettes et les

couvercles peuvent se briser s'ils sent exposes & des

changements soudains de temperature ou & un impact tel

que coup brusque. Pour votre protection, le verre trempe est

con(_u pour eclater en d'innombrables pieces minuscules.

Ceci est normal. Les tablettes et les couvercles en verre sent

Iourds. Un soin special s'impose Iors de leur deplacement

pour eviter I'impact d'une chute.

Risque d'explosion

Garder les mat_riaux et les vapeurs inflammables, telle

que I'essence, loin du refrigerateur.

Le non-respect de cette instruction peut causer

un deces, une explosion ou un incendie.

Pour obtenir une aeration appropriee pour votre refrigerateur,

laisser un espace de 1/2"(12,70 mm) de chaque c6te. Laisser un

espace de 3" (7,5 cm) entre le dessus du refrig@ateur et le

dessous des armoires. Laisser au moins 1" (25,40 mm) entre

I'arriere du refrigerateur et lemur. Si votre refrig@ateur comporte

une machine a glagons, s'assurer qu'un espace additionnel est

prevu a I'arriere pour permettre les connexions des conduits

d'eau.

• Si vous installez votre refrig@ateur pres d'un mur fixe, laisser

un minimum de 2" (5,08 cm) du c6te des charnieres (selon le

modele) pour permettre a la porte de s'ouvrir sans

obstruction.

• Ctablir I'aplomb du refrigerateur. Voir "Fermeture des portes".

La page est en cours de chargement...

Inglis IPT184301 Le manuel du propriétaire

Marque: Inglis

Modèle: IPT184301

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Inglis IPT184301 Owner's manual

Inglis IPT184301 Le manuel du propriétaire

Ce manuel convient également à

Inglis IPT184301 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents