Honeywell RTH9585WF1004/W Manuel utilisateur

Marque: Honeywell

Modèle: RTH9585WF1004/W

Catégorie: Thermostats

Taper: Manuel utilisateur

Ce manuel convient également à

Wi-Fi Smart Color 7 Day Programmable Thermostat

User Guide

Read and save these

instructions.

For help please visit

yourhome.honeywell.com

RTH9585

Wi-Fi Series

Wi-Fi Color

Touchscreen

Programmable

Thermostat

In the box you will find

• Thermostat

• Wallplate

• Screws and anchors

• Quick Start Guide

Features of your Wi-Fi thermostat

With your new thermostat, you can:

• Connect to the Internet to monitor and control your heating/cooling system.

• View and change your heating/cooling system settings.

• View and set temperature and schedules.

• Receive alerts via email and get automatic upgrades.

• View outdoor temperature and humidity (requires Wi-Fi set up and registration).

• Thermostat ID Card

• Wire labels

• User Guide

69-2715EF—07 ii

Welcome

Congratulations on your purchase of a Honeywell

Wi-Fi color touchscreen programmable thermostat.

When registered to Honeywell’s Total Connect

Comfort Solutions, you can remotely monitor and

control the heating and cooling system in your home

or business—you can stay connected to your comfort

system wherever you go.

Honeywell’s Total Connect Comfort is the perfect

solution if you travel frequently, own a vacation home,

a business, or manage an investment property or if

you are simply looking for peace of mind.

This thermostat works with common 24 volt systems such as forced air, hydronic,

heat pump, oil, gas, and electric. It will not work with millivolt systems, such as a

gas fireplace, or with 120/240 volt systems such as baseboard electric heat.

MERCURY NOTICE: Do not place your old thermostat in the trash if it contains

mercury in a sealed tube. Contact the Thermostat Recycling Corporation at

www.thermostat-recycle.org or 1-800-238-8192 for information on how and

where to properly and safely dispose of your old thermostat.

NOTICE: To avoid possible compressor damage, do not run air conditioner if the

outside temperature drops below 50°F (10°C).

Need help?

Visit wifithermostat.com or call 1-855-733-5465 for assistance before returning the

thermostat to the store.

1 69-2715EF—07

About your new thermostat

Home screen quick reference ..............1

Business screen quick reference .........2

Installation

Installing your thermostat ..................... 3

Connecting to your Wi-Fi network ...... 10

Registering your thermostat online ....13

Operation

Setting the time/date ..........................15

Setting the fan ....................................15

Selecting system mode ......................16

Preset energy-saving schedules ........16

Adjusting program schedules ............. 17

Overriding schedules–home ...............18

Overriding schedules–business .........18

Viewing equipment status ..................19

Setting vacation hold–home ...............19

Setting holiday/event schedules–

business ..........................................20

Setting custom events–business ........ 20

Setting holiday schedule–business ....21

Setting holiday override–business ......22

Initiating occupancy mode–business ..22

Customizing screen color ................... 23

Setting preferences ............................23

Cleaning the thermostat screen ......... 24

Adjusting security settings ..................24

Software updates ...............................25

Unregistering your thermostat ............25

Smart Response Technology .............25

Pre-occupancy purge .........................26

Compressor protection ....................... 26

Auto changeover ................................26

Setting advanced preferences ............27

Changing system setup ......................28

Appendices

Frequently asked questions................30

Getting help and responding to

alerts ...............................................31

Troubleshooting ..................................32

Limited warranty .................................34

Table of contents

Quick reference: home use

FAN. Select fan mode.

HOME. Touch to

display Home screen.

Current time.

Outdoor conditions.

Outdoor temperature

and humidity appear

after registration.

Current status. Shows

system mode (heat/

cool).

MODE. Select system

mode (heat, cool, auto,

em heat).

SETTINGS. Touch to

display options. Start

here to set a program

schedule.

Current setting.

Change temperature

setting and select

temporary or

permanent hold.

Indoor conditions.

Shows indoor

temperature and

humidity.

69-2715EF—07 2

Quick reference: business use

Setting up your thermostat

Setting up your Wi-Fi programmable touchscreen thermostat is easy. It is

preprogrammed and ready to go as soon as it is installed and registered.

Install your thermostat.

Connect it to your home wireless network.

Before you begin, you may want to watch a brief installation video.

Use the QR Code

at the front of this guide, or go to

wifithermostat.com/support

FAN. Select fan mode.

HOME. Touch to

display Home screen.

Current time.

Outdoor conditions.

Outdoor temperature

and humidity appear

after registration.

Current status. Shows

system mode (heat/

cool).

Override. Touch to

temporarily override the

program schedule.

MODE. Select system

mode (heat, cool, auto,

em heat).

SETTINGS. Touch to

display options. Start

here to set a program

schedule.

Thermostat location.

Quickly identify which

thermostat is in control

of a specific area.

Current setting.

Change temperature

setting and select

temporary or

permanent hold.

Indoor conditions.

Shows indoor

temperature and

humidity.

3 69-2715EF—07

Installing your thermostat

You might need the following tools to install this thermostat:

• No. 2 Phillips screwdriver

• Pen

• Pencil

• Level (optional)

• Drill and bits (3/16” for drywall,

7/32” for plaster) (optional)

• Hammer (optional)

• Electrical tape (optional)

1 Switch OFF power to your

heating/cooling system.

Important! To protect your

equipment, switch OFF the power

to your heating/cooling system

at the breaker box or the system

switch.

M31535

Circuit

breaker

box

Heating/cooling

system power

switch

M33823A

If you have an older thermostat

with a sealed mercury tube, turn

to page ii for proper disposal

instructions.

Terminal

designation

2 Remove old thermostat faceplate

and leave wires connected.

2a Take a picture of the

wire connections for later

reference.

2b If no wire is connected to

a terminal labeled C or no

C terminal exists on the

old thermostat, view the

Alternate Wiring videos at

wifithermostat.com/videos

or reference the C-wire

addendum in the box.

Important! C wire is required

and is the power source for your

thermostat. Without a C wire, your

thermostat will not power up.

Note: You will need a

picture of your wire

connections to wire the

new thermostat.

69-2715EF—07 4

Installing your thermostat

3 Label the wires.

Use the supplied sticky tags

to label each wire as you

disconnect it. Label wires

according to the old thermostat

terminal designations, not by

wire color.

Note: If no tag matches a

terminal designation, write the

appropriate letter on a blank

sticky tag.

4 Remove wallplate.

Remove the old wallplate from

the wall after all wires have been

labeled and disconnected.

Blank tags

Sticky tag

Terminal

designation

MCR31537

Note: Wrap the wires around

a pencil to prevent them from

falling back into the wall.

LEVEL

HERE

MCR34499

W-

O/B

W2-

Aux/E

5 Mount wallplate for Wi-Fi

thermostat.

Mount your new wallplate

using screws and anchors

included with the thermostat.

If necessary:

Drill 3/16-in holes for drywall.

Drill 7/32-in holes for plaster.

Note: You may be able to use

your existing wall anchors. Hold

the wallplate up to the existing

anchors to check for alignment.

Wallplate

5 69-2715EF—07

Important! This thermostat requires a C, or common, wire for power. The C, or common,

wire brings 24 VAC power to the thermostat. If you are replacing an existing thermostat,

it might not have a C wire connected to it. Many older mechanical or battery operated

thermostats do not require a C wire. See the C Wire Addendum document included in

this package for more information. If you don’t have a C wire, try:

Note: Not all heating/cooling systems label the 24 VAC common C. Check your system

manual or contact the manufacturer to find out which terminal is the 24 VAC common.

View the Alternate Wiring videos at wifithermostat.com/videos

Wiring

For conventional heating/cooling systems (natural gas, oil or electric furnace, air

conditioner), see page 5. See “Glossary” on page 33 for further definition.

For a heat pump system, see page 6. See “Glossary” on page 33 for further

definition.

Installing your thermostat

MCR34540

W-

O/B

W2-

Aux/E

Wiring (Conventional System)

6A Wire the Wi-Fi thermostat to your

conventional system.

a Starting with the C Wire, match the

sticky tag on the wire to the terminal

labels.

You must have a C wire.

Straighten wire and gently slide

into

terminal hole until it clicks into place.

(If you need to remove a wire, use a

pen tip to press the terminal release

and then pull wire out.)

Note: Refer to the wiring picture you took

in Step 2.

Tip: To make it easier to slide the wire

into place, use a pen tip to hold down the

terminal release.

Note: The wiring for your

application might be different than

the wiring shown below.

Labels don’t match?

See alternate wiring keys

on pages 7-8.

Terminal release

Remove jumper loop ONLY if

you have both R and Rc wires.

EXAMPLE WIRING

Yours may look different

69-2715EF—07 6

Installing your thermostat

Wiring (Conventional System

continued)

c In the image on the right, check the

box next to each connection. You will

use this checklist in Step 9.

d Verify wire is firmly secured by gently

pulling on wire.

e Repeat steps a–d for all other wires.

f Push any excess wire back into the

wall opening after all wires are

installed.

g Continue to page 8.

Labels don’t match?

See alternate wiring keys

on pages 7-8.

Important!

Check the box for each wire

you connect. You will need

this information in Step 9.

W-O/B

W2-

Aux/E

Wiring (Heat Pump System)

6B Wire Wi-Fi thermostat to your heat pump.

a Starting with the C Wire, match the

sticky tag on the wire to the terminal

labels.

You must have a C wire. See page 5.

b Slide wire gently into terminal hole

until it clicks into place. (If you need

to remove a wire, use a pen tip to

press the terminal release and then

pull the wire out.)

Note: Refer to the wiring picture you took

in Step 2.

Tip: To make it easier to slide the wire

into place, use a pen tip to hold down the

terminal release.

Note: The wiring for your

application might be different than

the wiring shown below.

MCR34566

W-

O/B

W2-

Aux/E

AUX

Labels don’t match?

See alternate wiring keys

on pages 7-8.

Terminal release

Remove jumper loop ONLY if

you have both R and Rc wires.

EXAMPLE WIRING

Yours may look different

7 69-2715EF—07

Installing your thermostat

Wiring (Heat Pump System

continued)

c In the image on the right, check the

box next to each connection. You will

use this checklist in Step 9.

d Verify wire is firmly secured by gently

pulling on wire.

e Repeat steps a–d for all other wires.

Note: If old thermostat has separate

wires on AUX and E, use a wire nut to

attach both wires to a separate wire.

Slide this third wire into the W2-Aux/E

terminal.

f Push any excess wire back into the

wall opening after all wires are

installed.

g Continue to page 8.

Labels don’t match?

See alternate wiring keys

on pages 7-8.

Important!

Check the box for each wire

you connect. You will need

this information in Step 9.

W-O/B

W2-

Aux/E

Alternate wiring (Conventional System)

Use this if your wire labels

don’t match the terminal labels.

Note: You must have a C wire

or equivalent. See page 5.

Alternate wiring key (Conventional System)

• If you have both an R and Rc wire, unplug the jumper loop by pulling on the wire

loop.

• If your old thermostat had both R and RH wires, connect the R wire to the Rc

terminal, the RH wire to the R terminal, and unplug the jumper loop.

MCR36751

W-

O/B

W2-

Aux/E

69-2715EF—07 8

Installing your thermostat

Alternate wiring (Heat Pump System)

Use this if your wire labels

don’t match the terminal labels.

Note: You must have a C wire

or equivalent. See page 5.

Alternate wiring key (Heat Pump System)

7 Attach thermostat to wallplate.

Align the thermostat with the

wallplate and then snap into place.

Thermostat

Wallplate

LEVEL

HERE

M34498

If you have both an R and Rc wire, unplug the jumper loop by pulling on the wire

loop.

If your old thermostat had both R and RH wires, connect the R wire to the Rc

terminal, the RH wire to the R terminal, and unplug the jumper loop.

If your old thermostat had both V and VR wires, check wifithermostat.com for help.

If your old thermostat had separate O and B wires, and is controlling a single zone

heat pump system, attach the B wire to the C. If there is more than one thermostat

controlling the system, call Honeywell zoning at 800-828-8367 for wiring assistance.

If your old thermostat had separate Y1, W1, and W2 wires, check

wifithermostat.com for help.

If the old thermostat has separate wires on Aux and E, use a wire nut to attach both

wires to a separate wire. Slide this third wire into the W2-Aux/E terminal.

This is the system monitor. If the monitor finds a problem, you will see an orange alert

button on the thermostat home screen.

MCR36752

W-

O/B

W2-

Aux/E

AUX

XX2

WW1

9 69-2715EF—07

Installing your thermostat

8 Switch heating/cooling system ON.

Important!

8a Verify that the C wire is

connected at the thermostat and

at the heating/cooling system.

8b Make sure the heating/cooling

system door is firmly secured.

8c Switch power back ON for your

heating/cooling system at the

breaker box or its power switch.

M31544

Circuit

breaker

box

Heating/cooling

system power

switch

Before connecting to your Wi-Fi network,

you need to set initial thermostat options

to define your heating/cooling system:

• Language

• Home or business

You can customize other options later.

9 Follow prompts on the screen to select

appropriate options.

9a Touch the language you want the

thermostat to display, then touch

Next.

9b Select Home or Business

installation, then touch Next.

9c Touch Next, or name the thermostat

location—touch THERMOSTAT and

follow the rest of the instructions.

9d Select what type of heating and

cooling equipment your thermostat

will control and touch Next.

Note: Touch the orange Help button on any

screen for more information.

69-2715EF—07 10

Installing your thermostat

9e Select your system type and touch

Next. The system type determines

other selections for completing initial

setup. Use the checklist from Step

6A-d when making selections.

9f Touch Next after making selections

on each screen.

9g Touch Done on the last screen. The

thermostat displays an option to

connect to your Wi-Fi network.

Note: Touch the orange Help button on

any screen for more information.

Connecting to your Wi-Fi network

After touching

Done

on the final screen of the

initial set up, the thermostat displays an option to

connect to your Wi-Fi network.

1 Connect the Wi-Fi network.

Touch Yes to connect the thermostat to your

Wi-Fi network. The screen displays the

message “Searching for wireless networks.

Please wait...” after which it displays a list of

all Wi-Fi networks it can find.

Note: If you cannot complete this step now,

touch

I’ll do it later

. The thermostat will display

the home screen. Complete this process by

selecting

SETTINGS

Wi-Fi Setup

. Continue with

Step 2.

2 Select the network.

2a Touch the name of the network you

want to use. The thermostat displays a

password page.

Yes

Your Network

Note: If your home network is not

shown on the list, touch

Rescan

11 69-2715EF—07

2b Using the keyboard, touch the

characters that spell out your home

network password.

2c Touch Done. The thermostat displays

“Connecting to your network. Please

wait...” then shows a “Connection

Successful” screen.

2d Touch OK to display the registration

information screen.

2e Note your Thermostat MAC and

Thermostat CRC. You need these

numbers to complete online

registration.

Done

Connecting to your Wi-Fi network

To register your thermostat, follow the

instructions beginning on page 13.

Note: The Register Online screen remains

active until you complete registration and/or

touch Done.

Note: If you touch Done before you register

online, your home screen displays an

orange alert button telling you to register.

Touching that button displays registration

information and an option to snooze the

task.

Done

for remote

access

69-2715EF—07 12

Reconnecting your Wi-Fi network

1 Touch SETTINGS.

2 Select Wi-Fi Setup.

3 Touch the name of the network you want

to use. The thermostat may display a

password page.

4 To enter a password, touch characters to

spell out your home network password,

then touch Done.

5 The thermostat displays “Connecting

to your network. Please wait...” then a

“Connection Successful” screen.

6 Touch Next.

• If your thermostat is registered, you

will see your signal strength and other

status information. Touch Done.

• If the screen displays “Register

Online for Remote Access,” follow

instructions on page 13.

SETTINGS

Wi-Fi Setup

Disconnecting your Wi-Fi network

1 Touch SETTINGS.

2 Select Wi-Fi Setup.

3 Touch Disconnect from Network. The

thermostat will display a question to

confirm your selection.

4 Touch Yes to confirm that you want

to disconnect from the network. The

thermostat will display the Wi-Fi Setup

screen.

5 Touch OK to display the menu.

SETTINGS

Wi-Fi Setup

Disconnect from Network

13 69-2715EF—07

M31570

To view and set your Wi-Fi thermostat

remotely, you must have a Total Connect

Comfort account. Use the following steps.

1 Open the Total Connect Comfort web

site.

Go to mytotalconnectcomfort.com

View the Wi-Fi Thermostat

Registration video at

wifithermostat.com/videos

Registering your thermostat online

2 Login or create an account.

If you have an account,

click Login

– or –

click Create An Account

2a Follow the instructions on the screen.

2b Check your email for an activation

message from My Total Connect

Comfort. This may take several

minutes.

Note: If you do not receive a response,

check your junk mailbox or use an alternate

e-mail address.

2c Follow activation instructions in

the email.

2d Log in.

69-2715EF—07 14

Registering your thermostat online

3 Register your Wi-Fi thermostat.

After you are logged in to your Total

Connect Comfort account, register

your thermostat.

3a Follow the instructions on

the screen. After adding your

thermostat location, you must

enter the thermostat’s unique

identifiers:

• MAC ID

• MAC CRC

Note: These IDs are listed on the

Thermostat ID Card included in the

thermostat package. The IDs are not

case sensitive.

® U.S. Registered Trademark.

69-2723EFS—01 M.S. 04-12

Printed in U.S.A.

HONEYWELL MODEL: RTH8580WF

MAC ID: MAC CRC:

69-2723EFS-01

Thermostat ID Card

Use the MAC ID and CRC ID to register

this product at mytotalconnectcomfort.com

Carte d’identification de thermostat

enregistrer ce produit à mytotalconnectcomfort.com

Tarjeta de identificación del termostato

inscribir este producto en mytotalconnectcomfort.com

MAC ID MAC CRC

When the thermostat is

successfully registered, the Total

Connect Comfort registration

screen will display a SUCCESS

message.

You can now control your

thermostat from anywhere

through your laptop, tablet, or

smartphone.

GET IT ON

Download on

iTunes

Total Connect Comfort free

app is available for Apple

iPhone

, iPad

and iPod

touch

devices at iTunes

or at Google Play

for all

Android™ devices.

15 69-2715EF—07

Setting the time/date

1 Touch the current time. The screen displays

Set Time/Set Date.

2 Touch Set Time or Set Date.

3 Touch p or q until the proper time/date is

displayed.

4 Touch Done to save or Cancel to ignore

changes.

Note: This thermostat will automatically update

for daylight saving time (if observed in your

area) and all date/time information is stored.

If the thermostat is connected to Wi-Fi and

registered to Total Connect Comfort, the current

time is updated from the internet.

Done

Setting the fan

1 Touch FAN to display fan settings.

2 Touch On, Automatic, Circulate, or Follow

Schedule.

Note: Follow Schedule option only appears if

the fan is set for On or Circulate for one or more

program periods.

3 Touch Done to save and exit.

On: Fan is always on.

Automatic: Fan runs only when the heating or cooling system is

on.

Circulate: Fan runs randomly about 35% of the time (home use

only).

Follow Schedule: Follow Schedule is not an option if all programs

are set to fan auto (see pages

-18).

Note: Touch On, Automatic, or Circulate to temporarily override the

programmed fan schedule.

FAN

Done

12:12 am

69-2715EF—07 16

Preset energy-saving schedules

This thermostat uses default Energy Saver settings that can reduce your heating/

cooling expenses. To customize settings, see next page.

Wake 6:00 am 70° 78° 70° 78°

Leave 8:00 am 62° 85° 62° 85°

Return 6:00 pm 70° 78° 70° 78°

Sleep 10:00 pm 62° 82° 62° 82°

Cool

(Mon-Fri)Start time

Heat

(Mon-Fri)Period

Heat

(Sat-Sun)

Cool

(Sat-Sun)

Home Use

Occupied 1 8:00 am 70° 75° On

Unoccupied 1 10:00 pm 55° 85° Auto

Occupied 2* 12:00 am 70° 75° On

Unoccupied 2* 12:00 am 55° 85° Auto

CoolStart time HeatPeriod Fan

Business Use

* Period 2 is cancelled by default. If you activate it, the values shown above are

default settings.

Setting system mode

1 Touch MODE to display system settings.

2 Touch desired option:

Heat: Thermostat controls only the heating

system.

Cool: Thermostat controls only the cooling

system.

Off: Heating/cooling systems are off.

Automatic: Thermostat selects heating or

cooling as needed depending on the indoor temperature.

Emergency Heat (heat pumps with aux. heat): Controls

auxiliary/emergency heat. Compressor is locked out.

3 Touch Done to save and exit.

Note: The Automatic and Emergency Heat system settings may not

appear, depending on how your thermostat was installed. See “Auto

changeover” on page 26.

MODE

Done

17 69-2715EF—07

Adjusting program schedules

1 Touch SETTINGS.

2 Select Create/Edit Schedule.

• Touch View/Edit to view the full

schedule and make a quick

adjustment.

• Touch Guide Me to create a schedule

by answering simple questions.

• Touch I’ll do it myself to manually

create a program schedule.

Note: To reduce costs, use the pre-set

Energy Saver settings described on

page 16.

SETTINGS

Create / Edit Schedule

If you selected I’ll do it myself on the Create/

Edit Schedule screen follow these steps:

1 Select the days to schedule, touch Next.

2 Touch Wake to set your Wake time for

selected days.

6:00 am

Heat: 70°

Cool: 78°

Fan: Auto

WAKE

3 Touch p or q to set Heat and Cool

temperatures for the Wake period, then

touch Done.

4 Touch other time periods (Leave, Return,

Sleep) to set time and temperatures for

each.

5 Touch Done to save and exit.

Note: Touch Delete Period to eliminate any

unwanted time period.

Note: Touch Fan Settings to customize fan

settings for any time period.

Done

69-2715EF—07 18

Overriding schedules: home use

1 Touch p or q to adjust the

temperature (right side of screen)

and the Hold Until time. The schedule

will resume when the Hold Until time

expires.

2 Touch Permanent to keep the same

temperature until you change it or

resume the program schedule.

3 Touch Cancel Hold at any time to

resume the program schedule.

PERMANENT

Overriding schedules: business use

Touch p or q to adjust the temperature.

It will be maintained until the hold time

you set.

• To change the hold time, touch the

Hold Until arrow buttons. This time can

be adjusted up to the maximum time

set on the Override Duration screen in

Advanced Preferences (page 27).

• Touch Override to use a pre-set occupied

temperature if a person uses the room

during an unoccupied period. The new

temperature will be maintained for 1 hour

and can be adjusted up to the maximum

time set on the Override Duration screen

in Advanced Preferences (page 27).

The programmed schedule will resume when

the override timer expires. Touch Cancel Hold

at any time to resume the program schedule.

OVERRIDE

La page charge ...

Honeywell RTH9585WF1004/W Manuel utilisateur

Marque: Honeywell

Modèle: RTH9585WF1004/W

Catégorie: Thermostats

Taper: Manuel utilisateur

Ce manuel convient également à

Wi-Fi Smart Color 7 Day Programmable Thermostat

Télécharger le PDF

rapport

dans d''autres langues

English: Honeywell RTH9585WF1004/W User manual

Honeywell RTH9585WF1004/W Manuel utilisateur

Ce manuel convient également à

Honeywell RTH9585WF1004/W Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents