Power Fist 8843732 Le manuel du propriétaire

V1.0 8843732

Please read and understand all instructions before use. Retain this manual for

future reference.

1/

4 IN.

8843732 1/4 in. Air Riveter V1.0

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Air Inlet 1/4 in.

Rivet Size 1/4, 3/16, 5/32, 1/8 in.

Air Consumption 0.03 CFM

Pressure Rating 90 PSI

Pulling Force 3,083 lb

Material Aluminum and Steel Housing

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A

notice is an alert that there is a possibility of property damage, injury or

death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that

will result in severe personal injury or death if the proper

precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may

result in minor or moderate injury if proper practices are not

taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice

will result in equipment or property damage, but not personal

injury.

V1.0 1/4 in. Air Riveter 8843732

Visit www.princessauto.com for more information 3

INTRODUCTION

The 1/4 in. Air Riveter is ideal for installing 1/8 to 1/4 in. long blind rivets. The

air riveter can use either steel or aluminum rivets. The air riveter holds the

ejected pins into a clear safety cap for later disposal.

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personal injury

and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection

and maintenance instructions.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-

lit and free of distractions. Place lights so you are not working in a

shadow.

2. Keep anyone not wearing the appropriate safety equipment away from

the work area.

3. Store unused tools properly in a safe and dry location to prevent rust

or damage. Lock tools away and keep out of the reach of children.

4. Do not install or use in the presence of flammable gases, dust or

liquids.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side

protection for the eyes. Eye protection equipment should comply with

CSA Z94.3-07 or ANSI Z87.1 standards based on the type of work

performed.

2. Wear gloves that provide protection based on the work materials or to

reduce the effects of tool vibration.

3. Wear protective clothing designed for the work environment and tool.

4. Non-skid footwear is recommended to maintain footing and balance in

the work environment.

8843732 1/4 in. Air Riveter V1.0

4 For technical questions call 1-800-665-8685

5. Wear steel toe footwear or steel toe caps to prevent a foot injury from

falling objects.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and balance

enables better control in unexpected situations.

4. Support the workpiece or clamp it to a stable platform. Holding the

workpiece by hand or against your body may lead to personal injury.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a specific

function. Do not modify or alter this tool or use it for an unintended

purpose.

2. Do not use the tool if any parts are damage broken or misplaced.

Repair or replace the parts.

3. Never point the tool towards yourself. It could inflict an injury.

4. Never use the riveter without the safety cap (D) in place. The ejected

pin may cause an injury to yourself or a bystander.

AIR TOOL PRECAUTIONS

1. Use only clean and dry compressed air as a power source. Contaminated

or moist air will gradually damage the tool.

2. Install an in-line shutoff valve or regulator to allow immediate control

over the air supply in an emergency, even if a hose is ruptured.

3. Discontinue tool use if it does not work properly or air is leaking. Tag

or mark the tool as ‘defective’ or ‘out of service’ until repaired.

4. Check the manufacturer’s maximum pressure rating for air tools and

accessories. Compressor outlet pressure must be regulated to never

V1.0 1/4 in. Air Riveter 8843732

Visit www.princessauto.com for more information 5

exceed the maximum pressure rating of the tool (see Specifications).

Exceeding the maximum PSI rating can create a bursting hazard,

causing injury and property damage.

5. Never use oxygen, combustible gas or any other bottled gas as a

power source. Any power source other than an air compressor could

cause an explosion and serious personal injury.

6. Turn OFF the valve and discharge any remaining air pressure after each

use or before adjusting the tool.

7. Do not leave the air tool unattended with its compressed air supply on.

Turn off the compressed air supply and bleed the air tool of any

remaining compressed air before leaving the air tool unattended.

8. Serious injury may occur from loose debris being propelled at high speeds

from the compressed air stream. Always wear OSHA approved safety

glasses to protect the eyes during operation of the air compressor.

9. Always turn off the air compressor and drain tank pressure completely

before attempting maintenance or attaching air tools. Release pressure

slowly from the system.

10. Serious injury or death may occur from inhaling compressed air. The air

stream may contain carbon monoxide, toxic vapors or solid particles.

Never inhale compressed air directly from the pump or air tool.

POWER TOOL PRECAUTIONS

1. Do not use any power tool with a malfunctioning power switch or

control. A power tool that fails to respond to the controls is dangerous

and can cause an injury. A qualified technician must repair and verify

the power tool is operating correctly, before it can be used.

2. Disconnect the power source before installing or servicing the tool.

3. Keep hands and fingers away from the work area. Any part of body

contacting the tool’s working parts could cause an injury.

4. Never touch the tool or workpiece during or immediately after use. They

may be hot and could inflict a burn injury.

AIR HOSE PRECAUTIONS

1. Inspect the tool's air hose for cracks, fraying or other faults before

each use. Discontinue use if the air hose is damaged or hissing is heard

from the air hose or connectors. Replace the defective air hose.

8843732 1/4 in. Air Riveter V1.0

6 For technical questions call 1-800-665-8685

2. Do not allow people, mobile equipment or vehicles to pass over the

unprotected air hose. Position the air hose away from high traffic

areas, in a reinforced conduit or place planks on both sides of the air

hose to create a protective trench.

3. Prevent damage to the air hose by observing the following:

a. Never carry the tool by the air hose.

b. Keep the air hose behind the tool and out of the tool's work path.

c. Keep the air hose away from heat, oil, sharp edges or moving parts.

d. Do not wrap the air hose around the tool as sharp edges may pierce

or crack the air hose. Gently coil the hose and either hang on a hook

or fasten with a device to keep hose together when storing.

4. A damaged or disconnected air hose under pressure may whip around

and inflict personal injury or damage the work area. Secure the

compressor's air hose to a fixed or permanent structure with clamps or

cable ties.

COMPRESSOR/TANK PRECAUTIONS

DANGER! Do not use an air tank beyond its expiration date. A tank rupture

or explosion may kill or cause a serious injury to yourself or a bystander.

Disable and discard the air tank according to the your municipality by-laws.

1. Never drill into, weld, patch or modify the air tank. Immediately

replace the tank or compressor if an air leak develops. The leak may

lead to a rupture.

2. Never make adjustments to the components that control tank pressure.

Serious injury or death may occur if modifications are made to the

pressure switch, safety relief valve or other components that control

the tank pressure.

3. Check operation of the pressure relief valve on a regular basis and

never operate without a factory approved pressure relief valve. Do not

make alterations to the factory operating pressure settings.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a malfunction

and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Make sure that all items in the contents are included.

V1.0 1/4 in. Air Riveter 8843732

Visit www.princessauto.com for more information 7

Contents: • Air Riveter • Wrench x 2 • Nosepiece x 4

• Jaw • O-ring x 4 (#B02 and B12)

IDENTIFICATION KEY

A Nosepiece

B Outer Sleeve

C Hanging Hook

D Safety Cap

E Trigger

F Air Filter

G Air Cylinder

H 1/4 in. Air Inlet

ASSEMBLY & INSTALLATION

Numbered references in parenthesis (#1) refer to the included Parts List.

Letter references in parenthesis (A) refer to the included Identification Key.

Dashed numbers in parenthesis (Fig. 1-1) refer to a specific point in an

illustration or image.

INSTALL AIR CONNECTOR

Prepare a standard 1/4 in. NPT male air connector (sold separately) for use

with your tool.

1. Wrap the external threads of the male connector with sealant tape.

a. Wrap tape in a clockwise direction so it will not unravel.

b. Do not tape all the threads. Leave several leading threads

unwrapped for easier alignment.

2. Screw the connector into the tool's air inlet (D) and tighten with a

wrench until snug.

3. Run the compressor at a low volume and check the connection for air

leaks. Do not use the tool until all air leaks are repaired or the faulty

component is replaced.

IMPORTANT! Vibration may cause failure if a quick coupler is connected directly

to the air tool. To overcome this, connect a leader hose to the tool. A quick

coupler may then be used to connect the leader hose to the air line hose.

Fig. 1

8843732 1/4 in. Air Riveter V1.0

8 For technical questions call 1-800-665-8685

NOSEPIECES

1. Remove the base cover (#34) from the air cylinder (Fig. 2)

2. Select the appropriate sized nosepiece (A) for your task from the four

nosepieces stored in the bottom (Fig. 3).

3. Fit the wrench’s center hex (#C02) over the nosepiece and twist

counterclockwise to free it (Fig. 3)

4. Insert the nosepiece into the jaws (#4) within the outer sleeve (B) and twist

clockwise (view from front) to lock it in place (Fig. 4). Remove the wrench.

.

OPERATION

WARNING! Always fit the safety cap (#15) to the rear of the air riveter before

use to prevent a penetrating injury from an ejected rivet mandrel.

CAUTION! Keep fingers away from the trigger while inserting the rivet into

the air riveter. Accidental activation may cause a cut or pinching injury.

One or more holes of the same diameter as the rivet must be drilled into the

workpiece before installing the rivets.

1. Check the hydraulic oil level before each use (See Adding Hydraulic Oil).

2. Select the correct nosepiece based on the rivet diameter and install per

Nosepieces section.

3. Attached the air riveter to the air source and start the compressor.

4. Push the rivet mandrel (stem) through the nosepiece until the rivet

head touches the nosepiece.

5. Insert the mandrel head and rivet pin into the pre-drilled hole. Push the

nosepiece against the workpiece.

6. Squeeze the trigger. The mandrel head will compress the rivet pin

while the mandrel is pulled through the air riveter. The force will snap

Fig. 2

Fig. 3

Fig. 4

V1.0 1/4 in. Air Riveter 8843732

Visit www.princessauto.com for more information 9

the mandrel at the rivet head and eject the scrap mandrel into the

safety cap.

7. Repeat Steps 3 to 5 until all rivets are installed.

8. Shut the compressor down and discharge all air from the system

before changing the nosepiece for a different diameter rivet.

9. Empty the safety cap when necessary. Make sure a rivet is not inserted

into the nosepiece when emptying the cap as an ejected mandrel may

cause a penetrating injury.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient, easier

to control and will have fewer problems.

2. Inspect the tool fittings, alignment, hoses and power supply cord

periodically. Have damaged or worn components repaired or replaced by

an authorized technician. Only use identical replacement parts when

servicing.

3. Follow instructions for lubricating and changing accessories.

4. Only use accessories intended for use with this tool.

5. Keep the tool handles clean, dry and free from oil/grease at all times.

6. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd. for

replacements.

WARNING! Only qualified service personnel should

repair the tool. An improperly repaired tool may

present a hazard to the user and/or others.

ADDING HYDRAULIC OIL

NOTICE! Do not overfill the air cylinder with hydraulic

oil. This can impair the tool’s function.

1. Disconnect the air hose from the riveter.

2. Invert the tool and remove the base cover.

a. Place the tool in a vise to free up both

hands.

3. Remove the nosepiece storage.

Fig.

5

8843732 1/4 in. Air Riveter V1.0

10 For technical questions call 1-800-665-8685

4. Unscrew the air cylinder cover (#24) by turning the nut

counterclockwise and then lifting the cover and piston assembly away

from the cylinder (Fig. 5).

5. The hydraulic oil level should barely cover the lock nut (#18)

connecting the air cylinder to the handle (#11).

Add hydraulic oil until the level is just above

the connection (fig. 6-1).

6. Lightly lubricate the inner wall of the air

cylinder.

7. Press the piston and air cylinder cover

assembly back into place as far as possible.

Tighten the nut.

8. Refit the nosepiece storage and base cover onto the air cylinder.

ADJUSTING THE STROKE LENGTH

1. Remove the outer sleeve using the box end of

wrench (#C02).

2. Confirm the piston stroke is set to 70 mm length.

The wrench shaft (#C03) is designed for this

measurement. The piston fits into the front

notch. The wrench’s butt will touch the threads

for the outer sleeve if the piston is properly

adjusted. (Fig. 7). Otherwise adjust the piston.

3. Slide the small wrench’s (#C02) open end onto

the flats of the socket (#7).

4. Slide the large wrench’s (#C03) open end onto

the clamp nut (#08).

5. Hold the socket in place while loosening the nut.

Spin the nut backwards a bit (Fig. 8).

6. Rotate the piston forward or backwards until it

is the correct distance as measured with the

wrench.

7. Hold the socket in place again and tighten the

clamp nut.

8. Fit the outer sleeve cylinder back onto the air riveter and tighten.

Fig. 6

Fig. 7

Fig. 8

V1.0 1/4 in. Air Riveter 8843732

Visit www.princessauto.com for more information 11

CLEANING AND CHANGING THE JAWS

1. Remove the outer sleeve with the small wrench’s

(#C02) box end.

2. Slide the small wrench’s (#C02) open end onto

the flats of the socket (#7).

3. Slide the large wrench’s (#C03) open end onto

the jaw carrier’s (#3) flats.

4. Hold the socket still while unscrewing the jaw

carrier (Fig. 9).

5. Remove the jaw assembly (#04) carefully to

prevent the spring from ejecting one or more jaws.

6. Clean the jaws with mild solvent and a brush. Dry and inspect for

damage. Replace the jaws if they are blunt.

7. Lightly oil the jaws and place the jaw assembly back into position.

Screw the jaw carrier into place. Tighten with both wrenches

8. Check and adjust the stroke length (see Adjusting the Stroke Length).

9. Fit the outer sleeve cylinder back onto the air riveter and tighten.

O-RING REPLACEMENTS

Replacement O-rings for #B02 and B12 are included for the connections

between the front and rear sections of the riveter and between the handle

and air cylinder. Refer to the Parts Breakdown for the exact location.

CLEANING

1. Clean with a soft cloth and mild detergent. Do not use solvents for

general cleaning.

2. Deposits may accumulate in the tool’s air inlet. Clean the air inlet and

flush the tool with a suitable gum solvent. You may need to

disassemble the tool for cleaning. Dry thoroughly before reassembly.

3. Continuing tool impairment after cleaning may indicate worn or

damage components. Repair the tool or have a certified technician

repair it for you.

AIR TOOL LUBRICATION

NOTICE! Only use air tool oil to lubricate the tool. Other lubricants are not

suitable and will damage the tool or cause a malfunction during use.

Fig. 9

8843732 1/4 in. Air Riveter V1.0

12 For technical questions call 1-800-665-8685

NOTICE! Never use a penetrating oil to lubricate an air tool. Penetrating oil

acts as a solvent that will dissolve the tool’s grease packing and may

damage the o-rings, causing the tool to seize or malfunction.

1. All air tools have an internal coating of grease to prevent corrosion

during shipping and storage. Remove this grease by adding a generous

amount of air tool oil in the air inlet and then run the tool under no

load until the exhaust is clear.

2. Manually add a drop or two of air tool oil into the tool’s male connector

before each use and after every hour of continuous use. The tool will

not work properly without lubrication and parts will wear prematurely.

3. Avoid adding too much air tool oil as this can cause premature power

loss and eventual tool failure. A qualified technician will need to take

the tool apart and clean out the excess oil.

4. Apply a generous amount of air tool oil to the tool before storing it for

an extended period of time (overnight, weekend, etc.). Run the tool for

approximately 30 seconds to ensure the oil is evenly distributed

throughout the tool. Store it in a clean and dry location.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or by-laws for

electronic devices, batteries, oil or other toxic liquids.

IMPORTANT! DO NOT pollute the environment by allowing uncontrolled

discharge of waste oil.

DISPOSAL OF HYDRAULIC FLUID

Do not drain hydraulic oil into the sewer system or dispose in an

uncontrolled location. Hydraulic fluid may take up to a year to breakdown in

the environment and the ingredients may still be toxic. Contact your local

municipality for proper disposal instructions or locations.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualified technician

service the tool.

V1.0 1/4 in. Air Riveter 8843732

Visit www.princessauto.com for more information 13

Problem(s) Possible Cause(s) Suggested Solution(s)

Tool runs at

normal speed, but

loses power

under load.

Motor parts worn.

1. Have a qualified technician

service the tool.

2. Replace tool or parts.

Tool runs slowly.

Air flows slightly

from exhaust.

Motor parts jammed with

dirt particles.

OR

Airflow blocked by dirt.

1. Check air inlet filter for

blockage.

2. Pour air tool lubricating oil

into air inlet as per

lubrication instructions for

clearing shipping grease.

3. Operate tool in short bursts

to clear debris.

4. If tool still jammed, clean tool

and lubricate per lubrication

instructions.

Tool runs slowly.

Air flows slightly

from exhaust.

1. Air regulator in closed

position.

2. Damage or excessive

wearing of internal parts.

1. Open the air regulator to

desired airflow.

2a. Have a qualified technician

service the tool.

2b. Replace tool or parts.

Tool will not shut

off.

1. Throttle valve o-ring

dislodged from inlet

valve seat.

2. Trigger mechanism

jammed or dirty.

1. Replace throttle valve

o-rings.

2. Clean trigger mechanism and

lubricate.

Loss of power or

erratic

performance.

1. Excessive drain on the

air hose. Incorrect size or

type of hose connectors.

2. Moisture or restriction in

the air hose/tank

3. Air compressor has

insufficient flow.

1. Check the air hose and

confirm the hose fitting is

correct for the inlet bushing.

2. Depressurize system and

drain tank and air hose of

water.

3. Ensure tool is connected to a

compressor with a rate flow

that matches the tool.

The jaws will not

open.

1. The nosepiece is loose.

2. The jaws are dirty.

1. Tighten the nosepiece.

2. Remove and clean the jaws.

8843732 1/4 in. Air Riveter V1.0

14 For technical questions call 1-800-665-8685

Problem(s) Possible Cause(s) Suggested Solution(s)

The stroke is too

short.

1. The rivet pin is not

properly inserted into

the riveter.

2. The riveter is low on

hydraulic oil.

3. The rivet is the wrong

size

4. Piston stroke is

misadjusted.

1. Fully insert the rivet pin.

2. Top up the hydraulic oil

reservoir and prime the

riveter.

3. Use the proper rivet length.

4. Adjust the piston stroke.

The riveter has

weak pulling

action.

1. Low air pressure.

2. Inadequately sized

compressor.

3. Damaged air compressor.

4. The riveter is low on

hydraulic oil.

1. Check the regulator to verify

that it is set to 90 PSI.

2. Upgrade to a suitable

compressor of adequate

capability.

3.

Have the compressor serviced

by a qualified service centre.

4. Top up the hydraulic oil

reservoir and prime the

riveter.

Leaking air.

1. There are poor hose

connections in the

system.

2. Damaged O-ring.

3. Dirty air valve or air

inlet.

1. Reconnect the air system

using thread sealant tape on

the fittings.

2. Replace the O-ring.

3. Clean and lubricate with

pneumatic tool oil.

V1.0 1/4 in. Air Riveter 8843732

Visit www.princessauto.com for more information 15

PARTS BREAKDOWN

8843732 1/4 in. Air Riveter V1.0

16 For technical questions call 1-800-665-8685

PARTS LIST

# DESCRIPTION QTY

1

Nosepiece 4

2

Outer sleeve 1

3

Jaw carrier 1

4

Jaw assembly 3

5

Riveter pusher 1

6

Spring 1

7

Socket 1

8

Clamp nut 1

9

Principal axis 1

10

Plastic ring 2

11

Handle 1

12

Lead axis 1

13

Plastic ring 1

14

Restore spring 1

15

Safety Cap 1

16

Airproof lid 1

17

Silencer 1

18

Lock nut 1

19

Air cylinder 1

20

Pole 1

21

Cushion 1

22

Piston 1

23

Nut 1

24

Air cylinder cover 1

25

Trigger 1

26

Linker 1

27

Press plank 1

28

Air valve 1

29

Valve spring 1

30

Copper washer 1

31

Plastic seal 1

32

Spring 1

33

Nut 1

34

Base cover 1

B01

O-ring 2

B02

O-ring 1

B03

O-ring 1

B04

O-ring 2

B05

O-ring 1

B06

Bolt 1

B07

Bolt 1

B08

Bolt 1

B09

Bolt 1

B10

O-ring 1

B11

O-ring 1

B12

O-ring 1

B13

O-ring 1

B14

O-ring 1

C01

Air inlet 1

C02

Wrench 1

C03

Wrench 1

V1.0 1/4 in. Air Riveter 8843732

Visit www.princessauto.com for more information 17

8843732 1/4 in. Air Riveter V1.0

18 For technical questions call 1-800-665-8685

V1,0 8843732

Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.

Conservez ce manuel afin de pouvoir le consulter plus tard.

DE 1/4 PO

8843732 Riveteuse pneumatique de 1/4 po V1,0

2 En cas de questions techniques, appelez le 1-800-665-8685

SPÉCIFICATIONS

Entrée d’air 1/4 po

Taille de rivet 1/4, 3/16, 5/32, 1/8 po

Consommation d’air 0,03 pi cubes/min

Pression nominale 90 lb/po carré

Force de tirage 3,083 lb

Matériau Boîtier en aluminium et acier

DÉFINITIONS DE DANGER

Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce

manuel. Un avis est une alerte indiquant qu'il existe un risque de dommage

à la propriété, de blessure ou de décès si on ne respecte pas certaines

instructions.

DANGER ! Cet avis indique un risque immédiat et particulier qui

entraînera des blessures corporelles graves ou même la

mort si on omet de prendre les précautions nécessaires.

AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique non

sécuritaire qui

pourrait entraîner des blessures

corporelles graves ou même la mort si on omet de

prendre les précautions nécessaires.

ATTENTION ! Cet avis indique une situation possiblement dangereuse qui

peut entraîner des blessures mineures ou modérées si on

ne procède pas de la façon recommandée.

AVIS ! Cet avis indique un risque particulier ou une pratique non

sécuritaire qui entraînera des dommages au niveau de

l'équipement ou des biens, mais non des blessures

corporelles.

La page charge ...

Power Fist 8843732 Le manuel du propriétaire

Power Fist 8843732 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents