Power Fist 8474983 Le manuel du propriétaire

V0.1 8474983

Please read and understand all instructions before use. Retain this manual for

future reference.

8474983 20 Gallon Portable Air Compressor V0.1

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Air Delivery 3.5 CFM @ 90 PSI

4.8 CFM @ 40 PSI

Air Tank Capacity 20 Gallons (76 litres)

Max. Air Pressure 125 PSI

Cut-In Pressure 95 PSI

Cut-Out Pressure 125 PSI

Compressor Type Direct Drive, Single Stage

Pump Style Oil Free

Current Rating 15A

Voltage Rating 120V, 60Hz

Duty Cycle 50%

Noise Rating 82 dB

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A

notice is an alert that there is a possibility of property damage, injury or

death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that

will result in severe personal injury or death if the proper

precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may

result in minor or moderate injury if proper practices are not

taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice

will result in equipment or property damage, but not personal

injury.

V0.1 20 Gallon Portable Air Compressor 8474983

Visit www.princessauto.com for more information 3

INTRODUCTION

The 20 Gallon Portable Air Compressor is ideal for light duty pneumatic tool

applications and general household use. The compressor is low maintenance

with a direct drive motor and oil free pump. The 20 gallon ASME vertical

portable tank comes with a cushioned handle grip. Fully enclosed plastic

shroud covers working components. The compressor plugs into a standard

120 volt outlet for quick and easy use.

The compressor is equipped with pressure regulator, pressure gauges, quick

connect air outlet and ON/OFF switch.

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personal injury

and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection

and maintenance instructions.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well lit

and free of distractions.

2. Keep anyone not wearing the appropriate safety equipment away from

the work area.

3. Store the device properly in a safe and dry location. Keep out of the

reach of children.

4. Do not install or use in the presence of flammable gases or liquids. Always

operate compressor in a well ventilated area. Locate the compressor at

least 20 feet away from work area if spraying flammable materials.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Wear personal protection equipment such as ANSI Z87.1 approved safety

goggles, respirator, gloves, steel toe footwear or a hard hat as

warranted by the work environment.

a. This device can cause hearing damage. Wear hearing protection

with an appropriate Noise Reduction Rating, especially if using it

for extended periods.

8474983 20 Gallon Portable Air Compressor V0.1

4 For technical questions call 1-800-665-8685

2. Control the device, personal movement and the work environment to

avoid personal injury or damage to the device.

3. Do not operate any device when tired or under the influence of drugs,

alcohol or medications.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and balance

enables better control in unexpected situations.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a specific function.

Do not modify or alter this tool or use it for an unintended purpose.

2. Do not use the tool if any parts are damage broken or misplaced. Repair

or replace the parts.

3. Risk of Bursting

a. Serious injury or death may occur from an air tank explosion if the air

tank is not properly maintained or if modifications, alterations or

repairs are attempted. Drain air tank daily or after each use. Never

drill into, weld, patch or modify the air tank. Replace the tank

immediately or replace the entire compressor, if a leak develops.

b. Serious injury or death may occur if modifications are made to the

pressure switch, safety relief valve or other components that

control the tank pressure. Never make adjustments to the

components that control tank pressure. Do not make alterations to

the factory operating pressure settings. Check operation of the

pressure relief valve on a regular basis and never operate without a

factory approved pressure relief valve.

c. Check the manufacturer’s maximum pressure rating for air tools

and accessories. Compressor outlet pressure must be regulated so

as to never exceed the maximum pressure rating of the tool.

V0.1 20 Gallon Portable Air Compressor 8474983

Visit www.princessauto.com for more information 5

4. Risk of Explosion or Fire

Serious injury may occur if a fire is caused by overheating due to

inadequate ventilation or restrictions to any of the compressor’s ventilation

openings. Never place objects against or on top of an air compressor.

Always operate air compressor at least 12 in. away from any wall or

obstruction. Always operate in a clean, dry and well-ventilated area.

5. Risk of Burn

Serious burn injuries could occur from touching exposed metal parts such

as the compressor head or motor during operation and even after the

compressor is shut down for some time. Never touch any of the exposed

metal parts during operation and for an extended period of time after the

air compressor has shut down. Do not attempt maintenance on the unit

until it has been allowed to completely cool.

6. Risk from Moving Parts

a. Serious injury may occur if repairs are attempted with damaged,

missing or removed protective guards, shrouds or missing covers.

All repairs to the air compressor should be made only by authorized

or trained service personnel.

b. This unit starts automatically. Always shut off the compressor and

bleed all pressure from the system before servicing the compressor

and when the compressor is not in use.

7. Flying Objects

a. Serious injury may occur from loose debris being propelled at high

speeds from the compressed air stream. Always wear OSHA

approved safety glasses to protect the eyes during operation of the

air compressor.

b. Never point the air stream or tools at any point of your body, other

people or animals. Debris and dust may be ejected without warning.

Always turn off the air compressor and drain tank pressure

completely before attempting maintenance or attaching air tools.

Release pressure slowly from the system.

8. Risk of Damage to Air Compressor or Property

a. Failure to transport or operate the air compressor properly may result

in major repair expenses. Always run the compressor in a level, secure

position that keeps it from tipping or falling during use.

b. Do not operate without an air filter or in a corrosive environment.

8474983 20 Gallon Portable Air Compressor V0.1

6 For technical questions call 1-800-665-8685

c. Always transport in a level position and use protective mats to keep

truck beds clean, etc. Fasten the compressor down securely. Pressure

must be released from the tank before transporting.

d. In cold climates, drain the tank after each use to avoid ice build up.

GENERAL SAFETY PRECAUTIONS

ELECTRICAL SAFETY

WARNING! To reduce risk of electric shock, be certain that the plug is

connected to a properly grounded receptacle.

1. Disconnect device from power source before cleaning, servicing,

changing parts/accessories or when not in use.

2. Protect yourself against electric shocks when working on electrical

equipment. Avoid body contact with grounded surfaces. There is an

increased chance of electrical shock if your body is grounded.

3. Do not disconnect the power cord in place of using the AUTO/OFF

switch on the device. This will prevent an accidental start up when the

power cord is plugged into the power supply.

4. Do not alter any parts of the device or accessories. All parts and

accessories are designed with built-in safety features that may be

compromised if altered.

5. Make certain the power source conforms to requirements of your

equipment.

6. To reduce the risk of electric shock, do not expose to rain or use on a

wet surface. Store the compressor indoors.

7. Use time delay fuses with this product when the circuit is connected to

a fuse box.

8. When wiring an electrically driven device, follow all electrical and

safety codes, as well as the most recent Canadian Electrical Code (CE)

and Canadian Centre for Occupational Health and Safety (CCOHS).

9. DO NOT use this device with a 2-prong wall receptacle.

a. Choose an available 3-prong power outlet.

b. Replace 2 prong outlet with a grounded 3-prong receptacle,

installed in accordance with the CE Code and local codes and

ordinances.

V0.1 20 Gallon Portable Air Compressor 8474983

Visit www.princessauto.com for more information 7

POWER CORD

1. Insert the power cord plug directly to the power supply whenever

possible. Use extension cords or surge protectors only when the

device's power cord cannot reach a power supply from the work area

(see below).

a. If an extension cord must be used, ensure it is at most 50 ft long

and at least 12 gauge wire thickness.

2. Do not operate this device if the power cord is frayed or damaged as an

electric shock may occur, resulting in personal injury or property

damage.

a. Inspect the device's power cord for cracks, fraying or other faults in

the insulation or plug before each use.

b. Discontinue use if a power cord feels more than comfortably warm

while operating the device.

c. Have the power cord replaced by a qualified service technician

3. Keep all connections dry and off the ground to reduce the risk of

electric shock. Do not touch plug with wet hands.

4. Prevent damage to the power cord by observing the following:

a. Do not pull on the cord to disconnect the plug from an outlet.

b. Keep cord away from heat, oil, sharp edges or moving parts.

5. Do not allow people, mobile equipment or vehicles to pass over

unprotected power cords.

a. Position power cords away from traffic areas.

b. Place cords in reinforced conduits.

c. Place planks on either side of the power cord to create a protective

trench.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a malfunction

and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Make sure that all items in the contents are included.

8474983 20 Gallon Portable Air Compressor V0.1

8 For technical questions call 1-800-665-8685

Contents:

• Air compressor

• 25 ft PE coil hose

• Blow gun with safety nozzle

• Inflation needle and adapter fitting

• Dual head tire chuck

• 1/4 in. female Quick coupler

• 1/4 in. NPT male and female QC

plugs

• Thread sealant

BASIC AIR COMPRESSOR COMPONENTS

Oil free air compressors are factory lubricated for life and do not require any oil.

The basic components of the air compressor are the electric motor, pump,

pressure switch and tank.

The electric motor (A) powers the pump. The electric

motor is equipped with an overload protector and an

automatic reset. If the motor becomes overheated,

the overload protector will shut it down to prevent

damage to the motor. When the motor sufficiently

cools, it will automatically reset.

The pump (A) compresses the air and discharges it

into the tank.

The tank (B) stores the compressed air.

The pressure switch (C) shuts down the motor when the

air pressure in the tank reaches the cut-out pressure. As

compressed air is used and the pressure level in the tank

drops to the cut-in pressure, the pressure switch restarts

the motor automatically, without warning and the pump

resumes compressing air.

COMPRESSOR CONTROLS

A. AUTO/OFF SWITCH

This switch turns on the compressor. It is operated manually, but when in

the AUTO position, it allows the compressor to start up or shut down

automatically, without warning, upon air demand. ALWAYS set this switch to

OFF when the compressor is not being used, and before unplugging the

compressor.

B. PRESSURE RELIEF VALVE

The air compressor is equipped with a pressure relief valve that is designed to

discharge tank pressure at a predetermined setting when a systems failure

occurs. Check the pressure valve periodically by pulling on the ring only when

Fig. 1

V0.1 20 Gallon Portable Air Compressor 8474983

Visit www.princessauto.com for more information 9

the tank pressure is completely drained. The spring

loaded valve should move freely within the

pressure valve body. An inoperable pressure valve

could allow an excessive amount of tank pressure

to build causing the air tank to catastrophically

rupture or explode.

Do not tamper with or attempt to eliminate the

pressure relief valve.

C. TANK PRESSURE GAUGE

This gauge measures the pressure level of the air

stored in the tank. It is not adjustable by the

operator, and does not indicate line pressure.

D. AIR PRESSURE REGULATOR

This air pressure regulator enables you to adjust line pressure to the tool

you are using. Turn the knob clockwise to increase pressure, and

counterclockwise to decrease pressure.

E. REGULATED PRESSURE GAUGE

This gauge measures the regulated outlet pressure.

F. AIR LINE OUTLET

Connect an air hose to this outlet.

ASSEMBLY & INSTALLATION

Letter references in parenthesis (A) refer to the

included Identification Key.

1. Remove the compressor from the carton and

place it on the floor or a hard, level surface.

The compressor must be level to ensure

proper drainage of the moisture in the tank.

2. The wheels are disassembled. Remove 2

wheels (D), 2 bolts (E), washers (F) and 2 nuts

(G) from the bag and install them on the foot

section of the tank as shown in (see Fig. 4).

3. Install the handle by placing the handle ends

(B) onto the base and secure with the bolts

(C) provided (see Fig. 4). Tighten bolts using a

13 mm socket or wrench (not included).

Fig. 2

Fig. 3

8474983 20 Gallon Portable Air Compressor V0.1

10 For technical questions call 1-800-665-8685

OPERATION

PRE-START CHECKLIST

1. Always operate the compressor in a level position to allow the tank to drain.

2. Inspect/clean/change intake elements on a regular basis. The ingestion

of dirt into the pump is the primary cause of premature wear. Check

intake filters daily.

3. Check tension of bolts and hardware on a regular basis. Operation of

any equipment with loose bolts and/or fittings will lead to excessive

vibration and the premature failure of the compressor system control

components.

4. Drain moisture from the air tank daily. Water is a natural by-product of

compressed air. Drain the air tank after each use to combat internal

tank corrosion. Keep drain valves open if storing compressor for any

length of time.

DAILY START UP

WARNING! High temperatures are generated by the electric motor and the

pump. To prevent burns or other injuries, DO NOT touch the compressor

while it is running. Allow it to cool before handling or servicing. Keep

children away from the compressor at all times.

WARNING! When adjusting from a higher to a lower pressure, turn the knob

anticlockwise past the desired setting, then turn clockwise to reach the desired

pressure. Do not exceed operating pressure of the tool or accessory being used.

1. Turn the pressure switch to the OFF position (A). (Fig. 2)

2. Close the tank drain valve (D). (Fig. 4)

3. Plug in the power cord.

4. Turn the pressure switch to the AUTO position (A). (Fig. 2)

5. Adjust the air pressure regulator to the working pressure of the tool

being used.

SHUTDOWN

1. Turn the pressure switch to the OFF position (A).

2. Unplug the power cord.

3. Reduce pressure in the tank by slowly opening the drain valve at the

bottom of the tank (B). The escaping air will also blow condensation out.

Leave the drain valve open until the next use.

V0.1 20 Gallon Portable Air Compressor 8474983

Visit www.princessauto.com for more information 11

CARE & MAINTENANCE

WARNING! Only qualified service personnel should repair the tool. An

improperly repaired tool may present a hazard to the user and/or others.

CAUTION! Always unplug or shut down your compressor and drain the air

tank completely before attempting any type of maintenance. Wait for

compressor to cool before servicing.

1. Maintain the device with care. A device in

good condition is efficient, easier to control

and will have fewer problems.

2. Inspect the device components

periodically. Repair or replace damaged or

worn components.

3. Follow instructions for lubricating and

changing accessories.

4. Drain tank of moisture after each day’s use.

If unit will not be used for a while, it is best

to leave drain valve open until such time as

it is to be used. This will allow moisture to

completely drain out and help prevent

corrosion on the inside of tank (Fig. 4).

5. Inspect the device fittings, alignment and

hoses periodically. Have damaged or worn

components repaired or replaced by an authorized technician.

a. Pull the pressure relief valve daily to ensure that it is operating

properly and to clear the valve of any possible obstructions.

b. Check that all connections are tight and don’t leak.

6. Maintain the device’s label and nameplate. These carry important

information. If unreadable or missing, contact Princess Auto Ltd. for

replacements.

Fig. 4

8474983 20 Gallon Portable Air Compressor V0.1

12 For technical questions call 1-800-665-8685

MAINTENANCE SCHEDULE

Recommendation Daily Weekly

Monthly

Quarterly Annually

Drain Moisture from Tank(s) X

Inspect Filter(s) X

Check for Unusual Noise or

Vibration

X

Check for Air Leaks X

Clean Exterior of Air Compressor

X

Tighten/Retorque Bolts

X

Check Operation of Pressure Relief

Valve

X

Clean/Change Filter

X

Perform Pump Up Time Test

X

Check Operation of System Controls

X

Check Air Tank(s) for Dents/Leaks

X

Inspect Tank for Rust, Pinholes, or

other Imperfections.

X

LUBRICATION

The oil free air compressor is factory lubricated for life and does not require

any oil for the pump.

STORAGE

Before storing the compressor for a prolonged period, use an air blowgun to

clean all dust and debris from the compressor. Disconnect the power cord

and coil it up on the handle. Open the drain valve to release all pressure

from the tank. This will also drain all moisture from the tank. Clean the filter

element and filter housing; replace the element if necessary. Drain the oil

from the pump crankcase and replace it with new oil. Cover the entire unit

to protect it from moisture and dust.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

V0.1 20 Gallon Portable Air Compressor 8474983

Visit www.princessauto.com for more information 13

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualified technician

service the tool.

Problem(s) Possible Cause(s) Suggested Solution(s)

Low pressure or

not enough air or

compressor does

not stop.

1. Tank drain valve is

open.

2. Fittings leak.

3. Restricted air intake.

4. Prolonged excessive

use of air.

5. Compressor not large

enough.

6. Hole in air hose.

7. Tank leaks.

8. Blown seals.

9. Valve leaks.

10. Leaking or worn

piston.

1. Close drain valve.

2.

Check fittings with soapy water.

Tighten or reseal leaking

fittings. DO NOT OVERTIGHTEN.

3. Clean or replace intake filter

element.

4. Decrease amount of air used.

5. Check air requirement of

accessory. If it is higher than

CFM and pressure supplied by

compressor, you need a larger

compressor. Most accessories

are rated at 25% of actual CFM

while running continuously.

6. Check and replace if necessary.

7. Immediately replace tank. DO

NOT attempt to repair.

8. Replace seals.

9. Replace valve.

10. Replace piston.

Air leaks from

regulator or

regulator does not

regulate pressure.

Dirty or damaged

regulator internal parts.

Dirty or damaged regulator internal

parts.

Regulated pressure

gauge reading drops

when air accessory

is being used.

1. This is normal.

2. Compressor not large

enough.

1. If pressure drops too low, adjust

regulator while accessory is

used.

2. Check air requirement of

accessory. If it is higher than

CFM and pressure supplied by

compressor, you need a larger

compressor. Most accessories

are rated at 25% of actual CFM

while running continuously.

8474983 20 Gallon Portable Air Compressor V0.1

14 For technical questions call 1-800-665-8685

Pressure relief valve

opens.

1. Tank pressure

exceeded normal

operating pressure.

2. Pressure switch

stuck.

1. Replace pressure switch.

2. Replace pressure switch.

Motor will not run. 1. Tank pressure

exceeds preset

pressure switch limit.

2. Fuse blown or circuit

breaker tripped

(make sure the

thermal overload

switch has not

tripped. The motor

has a built-in thermal

cut-out that trips to

protect the motor

from damage due to

overheating).

3. Check valve stuck

open.

4. Extension cord is too

long, too light gauge

or damaged.

5. Loose electrical

connections.

6. Paint spray on

internal motor parts.

7. Possible defective

motor.

1. Motor will start automatically

when tank pressure drops

below the cut-in pressure of

pressure tank.

2. Replace blown fuse or reset

circuit breaker. Do not use fuse

or circuit breaker with higher

rating than specified for your

branch circuit. To reset the

motor overload, turn the

pressure switch AUTO/OFF lever

to the OFF position and unplug

the unit from the power outlet.

Allow 10 minutes minimum for

motor overload cut-out to cool

and reset. Unit can then be

plugged in and re-started.

2a. Check for proper fuse. A

fuse type T, such as a

Fusetron, is acceptable.

2b. Check for low voltage and

proper extension cord size.

2c. Disconnect other

applications from circuit.

Operate compressor on a

dedicated circuit.

3. Remove and clean or replace.

4. Replace extension cord with

another one that is at most 50

ft long and at least 12 gauge.

5. Contact Princess Auto Ltd. for a

solution.

6. Do not operate compressor in

the paint spray area. Contact

Princess Auto Ltd. for a solution.

7. Contact Princess Auto Ltd. for a

solution.

V0.1 20 Gallon Portable Air Compressor 8474983

Visit www.princessauto.com for more information 15

PARTS BREAKDOWN

PARTS LIST - MOTOR

# DESCRIPTION QTY KIT PART ID

1

Screw, SHC M6 X 1.0 X 35 mm 4 7

2

Washer, Lock M6

6

4 & 7

3

Head, Cylinder 1 7

E100284

4

Screw, HFH M3 X 0.4 X 5 mm

2

1 & 7

5

Washer, Lock M3 1 1 & 7

6

Retainer, Outlet Valve

1

1 & 7

7

Valve, Outlet 1 1 & 7

8

Gasket, O-ring, Head

1

1, 7 & 10

8474983 20 Gallon Portable Air Compressor V0.1

16 For technical questions call 1-800-665-8685

9

Valve Plate

1

1 & 7

10

Gasket, O-ring, Cylinder

1

1, 7 & 10

11

Valve, Inlet

1

1 & 7

12

Retainer, Inlet Valve

1

1 & 7

13

Cylinder

1

2 & 7

14

Screw, Pan Head M6 x 1.0 x 10 mm

4

7

15

Shroud, Motor End Cap

1

7

E104779

16

Motor/Pump F2

1

7

17

Assy, Eccentric & Bearing 6203ZC3

1

3 & 7

18

Screw, SHCS M6 X 1 X 35 mm

1

3 & 7

19

Nut, M5 X 0.8

1

2 & 7

20

Screw, SHCS M5 X 0.8 X 25 mm

1

2 & 7

21

Rod, Connector

1

2 & 7

22

Ring, Piston

1

2 & 7

23

Cap, Piston

1

2 & 7

24

Screw, SHC M5 X 0.8 X 15 mm

1

2 & 7

25

Fan, Cooling

1

4

26

Washer, Flat M6

1

4

27

Screw, SHC M6 x 1.0 x 16 mm (Left Hand Thread)

1

4

28

Capacitor, Running (Motor-50μF/250VAC) Bkt Mt

1

7

E104273

29

Capacitor, Starting (Motor-250μF/125VAC) Bkt

Mt.

1

7

E104272

30

Nut, M8 x 1.25

2

7

31

---

V0.1 20 Gallon Portable Air Compressor 8474983

Visit www.princessauto.com for more information 17

PARTS LIST - COMPRESSOR

# DESCRIPTION QTY KIT PART ID

32

Shroud, Full Rear 1 E100300

33

Grip, Slide On, 20 mm

1

E101490

34

Handle 1 E103967

35

---

8474983 20 Gallon Portable Air Compressor V0.1

18 For technical questions call 1-800-665-8685

36

Gauge, Pressure 1.5 in. (Blk Hsn/White Face)

2

E103339

37

---

38

Coupling, Quick Connect

1

E100307

39

Cord, Power, 14/3 AWG, Length 6 ft Type ST

1

E101073

40

Restraint, Power Cord - 14/3 ST

1

E101800

41

Regulator, 3-Port, Left Flow 1/4 in. NPT

1

E100971

42

Nipple, 1/4 in. MNPT x 35 mm

2

E100853

43

Switch, Pressure Assy 125 PSIG 4 X 1/4 in. NPT Base

1

E104555

44

Valve, Safety

1

E102595

45

Weldment, Assembly Tank, 20 Gallon Vertical

1

46

Nut, Hex Lock Nylon Inserted M10 x 1.5 (Bright Zinc)

2

5

47

Washer, Flat M10

2

5

48

Wheel, 7 x 1.5 in. Diamond Tread

2

5

49

Bolt, Shoulder M10 x 1.5 x 55 (Shoulder To 39 mm)

2

5

50

Valve, Drain, 1/4 Turn

1

E101717

51

Screw, HH M8 X 1.25 Self Tap

2

52

Washer, Flat M8 X 22 mm

2

53

Isolator, Foot (60 mm Dia. x 28 mm Tall)

2

E100240

54

Washer, Flat M6 X 12 mm OD

2

55

Screw, HH M6 X 1.0 X 20 mm

2

56

Ferrule, 3/8 in.

1

6

57

Nut, Comp, 3/8 in.

1

6

58

Assy, 3/8 in. Finned Outlet Tube

1

6

59

Shroud, F2, Full, Front

1

E100296

60

Screw, HFH M6 x1.0 x 12 mm

6

61

Elbow, Exhaust 90 deg. 13 mm Male Flr X 1/2 in. MNPT

1

E100283

62

Motor/Pump Assembly F2B2 (Right Hand Exhaust)

7

63

Screw, SHC M8 x 1.25 x 16 mm (ZDC Plate)

4

64

Washer, Lock 8 mm

8

65

Washer, Flat 8 mm X 19 mm

8

66

Nut, M8 x 1.25

4

67

Valve, Check, 90 Degree Left

1

E101362

68

Tube, Relief, 1/4 in. Copper Formed (F2 On 400 mm Vert)

1

8

69

Nut, Comp, 1/4 in.

2

8

70

Ferrule, Comp 1/4 in.

2

8

71

Screw, HH M8 X 1.25 X 25 mm

4

V0.1 20 Gallon Portable Air Compressor 8474983

Visit www.princessauto.com for more information 19

72

Base, Air Filter

1

9

73

Element, Air Filter

1

9

E100435

74

Cap, Air Filter

1

9

PARTS LIST - KIT

KIT # KIT NAME PART # ORDER #

1 Kit, Valve Plate 4-12 E103497

2 Kit, Piston 13, 19-24 E103495

3 Kit, Eccentric 17-18 E104441

4 Kit, F2 Pump Fan 2, 25-27 E104280

5 Kit, Wheel (Replaces One Wheel Assy.) 46-49 E104442

6 Kit, Finned Aluminum 3/8 in. Outlet Tube 56-58 E103286

7 Kit, F2B2 Motor/Pump Assy (Right Hand Exhaust) 1 - 30, 62 E104279

8 Kit, Pressure Relief Tube 1/4 in. Copper 68-70 E104834

9 Kit, Air Filter 72-74 E100794

10 Kit, O-ring 8, 10 E105845

8474983 20 Gallon Portable Air Compressor V0.1

20 For technical questions call 1-800-665-8685

La page charge ...

Power Fist 8474983 Le manuel du propriétaire

Power Fist 8474983 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents