Bolens 31AH5ZLH565 Le manuel du propriétaire

Marque: Bolens

Modèle: 31AH5ZLH565

Catégorie: Souffleuses à neige

Taper: Le manuel du propriétaire

Ce manuel convient également à

31AH5WLF565

Safety • Assembly • Operation • Adjustments • Maintenance • Troubleshooting • Parts Lists • Warranty

MTD Products Ltd., P. O. Box 1386, KITCHENER, ONTARIO N2G 4J1

PRINTED IN U.S.A.

IMPORTANT:

READ SAFETY RULES AND

INSTRUCTIONS CAREFULLY

BEFORE OPERATION

OPERATOR’S MANUAL

Two-Stage Snow Thrower

769-04188

06/30/08

Finding and Recording Model Number

Please do

NOT

return the unit to the retailer from which it was purchased,

without rst contacting Customer Support.

Table of Contents

BEFORE YOU START ASSEMBLING

YOUR NEW EQUIPMENT,

please locate the model plate on the equipment and copy the

model number and the serial number to the sample model

plate provided to the right. You can locate the model plate by

standing at the operating position and looking down at the

frame.

This Operator’s Manual is an important part of your new snow thrower. It will help you assemble,

prepare and maintain the unit for best performance. Please read and understand what it says.

Customer Support

If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this unit,

you can seek help from the experts. Choose from the options below:

1. Visit www.bolens.ca/bolens for many useful suggestions, click on Customer Support button.

2. Call a Customer Support Representative at 1-800-668-1238

3. The engine manufacturer is responsible for all engine-related issues with regards to performance, power-rating, specifica-

tions, warranty and service. Please refer to the engine manufacturer’s Owner’s/Operator’s Manual, packed separately with

your unit, for more information.

Please have your unit’s model number and serial number ready when you call. See previous section to locate this information.

You will be asked to enter the serial number in order to process your call.

-4$02/$5#43,)-)4%$

+)4#(%.%2/..'*



8888888888

88888888888

-ODEL.UMBER

.UM£RODEMODÞLE

3ERIAL.UMBER

.UM£RODES£RIE

WWWMTDCANADACOM

Safety Symbols ................................................... 3

Safe Operation Practices ................................... 4

Setting Up Your Snow Thrower .......................... 6

Operating Your Snow Thrower ........................... 8

MakingAdjustments ......................................... 12

Maintaining Your Snow Thrower ...................... 14

Off-Season Storage .......................................... 16

Trouble Shooting .............................................. 17

Warranty ............................................................ 18

Illustrated Parts Lists ....................................... 19

Symbol Description

READ THE OPERATOR’S MANUAL(S)

Read, understand, and follow all instructions in the manual(s) before

attempting to assemble and operate.

WARNING— ROTATING BLADES

Keep hands out of inlet and discharge openings while machine is running.

There are rotating blades inside.

WARNING— ROTATING BLADES

Keep hands out of inlet and discharge openings while machine is running.

There are rotating blades inside.

WARNING— ROTATING AUGER

Do not put hands or feet near rotating parts, in the auger/impeller housing

or chute assembly. Contact with the rotating parts can amputate hands and

feet.

WARNING—THROWN OBJECTS

This machine may pick up and throw objects which can cause serious

personal injury.

WARNING—GASOLINE IS FLAMMABLE

Allow the engine to cool at least two minutes before refueling.

WARNING— CARBON MONOXIDE

Never run an engine indoors or in a poorly ventilated area. Engine exhaust

contains carbon monoxide, an odorless and deadly gas.

WARNING— ELECTRICAL SHOCK

Do not use the engine’s electric starter in the rain.

Safety

Symbols

This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all

instructions on the machine before attempting to assemble and operate.

WARNING

This symbol points

out important safety

instructions which,

if not followed, could

endanger the per-

sonal safety and/or

property of yourself

and others. Read and

follow all instructions

in this manual before

attempting to operate

this machine. Failure

to comply with these

instructions may

result in personal

injury. When you see

this symbol, HEED

ITS WARNING!

Your Responsibility

Restrict the use

of this power machine

to persons who read,

understand

and follow the warnings

and instructions

in this manual

and on the machine.

Safe

Operation

Practices

Training

1. Read, understand, and follow all instructions on the

machine and in the manual(s) before attempting to

assemble and operate. Keep this manual in a safe place for

future and regular reference and for ordering replacement

parts.

2. Be familiar with all controls and their proper operation.

Know how to stop the machine and disengage them quickly.

3. Never allow children under 14 years old to operate this

machine. Children 14 years old and over should read and

understand the instructions and safe operation practices

in this manual and on the machine and be trained and

supervised by an adult.

4. Never allow adults to operate this machine without proper

instruction.

5. Thrown objects can cause serious personal injury. Plan

your snow-throwing pattern to avoid discharge of material

toward roads, bystanders and the like.

6. Keep bystanders, helpers, pets and children at least 75 feet

from the machine while it is in operation. Stop machine if

anyone enters the area.

7. Exercise caution to avoid slipping or falling, especially

when operating in reverse.

Preparation

Thoroughly inspect the area where the equipment is to be

used. Remove all doormats, newspapers, sleds, boards, wires

and other foreign objects, which could be tripped over or

thrown by the auger/impeller.

1. Always wear safety glasses or eye shields during

operation and while performing an adjustment or repair

to protect your eyes. Thrown objects which ricochet can

cause serious injury to the eyes.

2. Do not operate without wearing adequate winter outer gar-

ments. Do not wear jewelry, long scarves or other loose

clothing, which could become entangled in moving parts.

Wear footwear which will improve footing on slippery

surfaces.

3. Use a grounded three-wire extension cord and receptacle

for all units with electric start engines.

4. Adjust collector housing height to clear gravel or crushed

rock surfaces.

5. Disengage all control levers before starting the engine.

6. Never attempt to make any adjustments while engine is

running, except where specifically recommended in the

operator’s manual.

7. Let engine and machine adjust to outdoor temperature

before starting to clear snow.

Safe Handling of Gasoline

To avoid personal injury or property damage use extreme care

in handling gasoline. Gasoline is extremely flammable and the

vapors are explosive. Serious personal injury can occur when

gasoline is spilled on yourself or your clothes, which can ignite.

Wash your skin and change clothes immediately.

a. Use only an approved gasoline container.

b. Extinguish all cigarettes, cigars, pipes and other sources

of ignition.

c. Never fuel machine indoors.

d. Never remove gas cap or add fuel while the engine is hot

or running.

e. Allow engine to cool at least two minutes before refuel-

ing.

f. Never over fill fuel tank. Fill tank to no more than ½ inch

below bottom of filler neck to provide space for fuel

expansion.

g. Replace gasoline cap and tighten securely.

h. If gasoline is spilled, wipe it off the engine and equip-

ment. Move machine to another area. Wait 5 minutes

before starting the engine.

i. Never store the machine or fuel container inside where

there is an open flame, spark or pilot light (e.g. furnace,

water heater, space heater, clothes dryer etc.).

j. Allow machine to cool at least 5 minutes before storing

k. Never fill containers inside a vehicle or on a truck or

trailer bed with a plastic liner. Always place containers on

the ground away from your vehicle before filling.

l. If possible, remove gas-powered equipment from the

truck or trailer and refuel it on the ground. If this is not

possible, then refuel such equipment on a trailer with a

portable container, rather than from a gasoline dispenser

nozzle.

m. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete.

Do not use a nozzle lock-open device.

WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo-

nents contain or emit chemicals known to State of California to cause cancer and

birth defects or other reproductive harm.

WARNING

This symbol points

out important safety

instructions which,

if not followed, could

endanger the per-

sonal safety and/or

property of yourself

and others. Read and

follow all instructions

in this manual before

attempting to operate

this machine. Failure

to comply with these

instructions may

result in personal

injury. When you see

this symbol,

HEED

ITS WARNING!

Your Responsibility

Restrict the use

of this power machine

to persons who read,

understand

and follow the warnings

and instructions

in this manual

and on the machine.

DANGER: This machine was built to be operated according to the safe operation practices in this

manual. As with any type of power equipment, carelessness or error on the part of the operator can

result in serious injury. This machine is capable of amputating hands and feet and throwing objects.

Failure to observe the following safety instructions could result in serious injury or death.

Operation

1. Do not put hands or feet near rotating parts, in the auger/

impeller housing or chute assembly. Contact with the

rotating parts can amputate hands and feet.

2. The auger/impeller control lever is a safety device. Never

bypass its operation. Doing so makes the machine unsafe

and may cause personal injury.

3. The control levers must operate easily in both directions

and automatically return to the disengaged position when

released.

4. Never operate with a missing or damaged chute assembly.

Keep all safety devices in place and working.

5. Never run an engine indoors or in a poorly ventilated area.

Engine exhaust contains carbon monoxide, an odorless and

deadly gas.

6. Do not operate machine while under the influence of alcohol

or drugs.

7. Muffler and engine become hot and can cause a burn. Do

not touch.

8. Exercise extreme caution when operating on or crossing

gravel surfaces. Stay alert for hidden hazards or traffic.

9. Exercise caution when changing direction and while operat-

ing on slopes.

10. Plan your snow-throwing pattern to avoid discharge towards

windows, walls, cars etc. Thus, avoiding possible property

damage or personal injury caused by a ricochet.

11. Never direct discharge at children, bystanders and pets or

allow anyone in front of the machine.

12. Do not overload machine capacity by attempting to clear

snow at too fast of a rate.

13. Never operate this machine without good visibility or light.

Always be sure of your footing and keep a firm hold on the

handles. Walk, never run.

14. Disengage power to the auger/impeller when transporting or

not in use.

15. Never operate machine at high transport speeds on slippery

surfaces. Look down and behind and use care when

backing up.

16. If the machine should start to vibrate abnormally, stop the

engine, disconnect the spark plug wire and ground it against

the engine. Inspect thoroughly for damage. Repair any

damage before starting and operating.

17. Disengage all control levers and stop engine before you

leave the operating position (behind the handles). Wait

until the auger/impeller comes to a complete stop before

unclogging the chute assembly, making any adjustments, or

inspections.

18. Never put your hand in the discharge or collector openings.

Always use the clean-out tool provided to unclog the dis-

charge opening. Do not unclog chute assembly while engine

is running. Shut off engine and remain behind handles until

all moving parts have stopped before unclogging.

19. Use only attachments and accessories approved by the

manufacturer (e.g. wheel weights, tire chains, cabs etc.).

20. When starting engine, pull cord slowly until resistance is felt,

then pull rapidly. Rapid retraction of starter cord (kickback)

will pull hand and arm toward engine faster than you can let

go. Broken bones, fractures, bruises or sprains could result.

21. If situations occur which are not covered in this manual, use

care and good judgment. Call customer assistance for the

name of your nearest servicing dealer.

Maintenance & Storage

1. Never tamper with safety devices. Check their proper

operation regularly. Refer to the maintenance and adjust-

ment sections of this manual.

2. Before cleaning, repairing, or inspecting machine disengage

all control levers and stop the engine. Wait until the auger/

impeller come to a complete stop. Disconnect the spark plug

wire and ground against the engine to prevent unintended

starting.

3. Check bolts and screws for proper tightness at frequent

intervals to keep the machine in safe working condition.

Also, visually inspect machine for any damage.

4. Do not change the engine governor setting or over-speed

the engine. The governor controls the maximum safe

operating speed of the engine.

5. Snow thrower shave plates and skid shoes are subject to

wear and damage. For your safety protection, frequently

check all components and replace with original equipment

manufacturer’s (OEM) parts only. “Use of parts which do

not meet the original equipment specifications may lead to

improper performance and compromise safety!”

6. Check controls periodically to verify they engage and

disengage properly and adjust, if necessary. Refer to the

adjustment section in this operator’s manual for instructions.

7. Maintain or replace safety and instruction labels, as neces-

sary.

8. Observe proper disposal laws and regulations for gas, oil,

etc. to protect the environment.

9. Prior to storing, run machine a few minutes to clear snow

from machine and prevent freeze up of auger/impeller.

10. Never store the machine or fuel container inside where

there is an open flame, spark or pilot light such as a water

heater, furnace, clothes dryer etc.

11. Always refer to the operator’s manual for proper instructions

on off-season storage.

12. Check fuel line, tank, cap, and fittings frequently for cracks

or leaks. Replace if necessary.

13. Do not crank engine with spark plug removed.

Do not modify engine

To avoid serious injury or death, do not modify engine in any

way. Tampering with the governor setting can lead to a runaway

engine and cause it to operate at unsafe speeds. Never tamper

with factory setting of engine governor.

Notice regarding Emissions

Engines which are certiﬁed to comply with California and federal

EPA emission regulations for SORE (Small Off Road Equipment)

are certiﬁed to operate on regular unleaded gasoline, and may

include the following emission control systems: Engine Modiﬁca-

tion (EM) Oxidizing Catalyst (OC), Secondary Air Injection (SAI)

and Three Way Catalyst (TWC) if so equipped.

Average Useful Life

According to the Consumer Products Safety Commission

(CPSC) and the U.S. Environmental Protection Agency (EPA),

this product has an Average Useful Life of seven (7) years, or

60 hours of operation. At the end of the Average Useful Life,

have the machine inspected annually by an authorized service

dealer to ensure that all mechanical and safety systems are

working properly and not worn excessively. Failure to do so can

result in accidents, injuries or death.

Safe

Operation

Practices

WARNING

This symbol points

out important safety

instructions, which

if not followed, could

endanger the per-

sonal safety and/or

property of yourself

and others. Read and

follow all instructions

in this manual before

attempting to operate

this machine. Failure

to comply with these

instructions may

result in personal

injury. When you see

this symbol, HEED

IT’S WARNING!

Your Responsibility

Restrict the use

of this power machine

to persons who read,

understand

and follow the warnings

and instructions

in this manual

and on the machine.

05.08.08

Setting Up

Your Snow

Thrower

IMPORTANT: The snow thrower is shipped with oil

and WITHOUT GASOLINE. After assembly, refer to

separate engine manual for proper fuel and engine oil

recommendations.

1. Observe the lower area of the snow thrower to be sure

both cables are aligned with roller guides.

a. Pull up and back on upper handle as shown in

Figure 3-1. Align upper handle with the lower

handle.

b. Tighten hand knobs securing upper handle to

lower handle.

2. Remove wing nut and hex screw from chute control

assembly and clevis pin and cotter pin from chute

support bracket. See Figure 3-2. Position the chute

assembly (forward-facing) over the chute base.

3. Place chute assembly onto chute base and secure

chute control assembly to chute support bracket with

clevis pin and cotter pin removed earlier. See Figure

3-3.

4. Finish securing chute control assembly to chute

support bracket with wing nut and hex screw removed

earlier. See Figure 3-4.

5. Check that all cables are properly routed through the

cable guide. See Figure 3-5.

Figure 3-3

Figure 3-2

Figure 3-1

Figure 3-5

NOTE: References to

right or left side of the

snow thrower are deter-

mined from behind the

unit in the operating

position.

NOTE: Two replace-

ment auger shear pins

are included with this

manual (or stowed

in the plastic handle

panel). Refer to Augers

in the Maintainance

Section for more

information regarding

shear pin replacement.

NOTE: This Operator’s

Manual covers several

models, handle panels,

lights and chute cranks

are some features that

may vary by model.

Not all features refer-

enced in this manual

are applicable to all

snow thrower models.

Figure 3-4

CAUTION

Prior to operating

your snow thrower,

refer to Auger Control

Test on page 11.

Read and follow all

instructions care-

fully and perform all

adjustments to verify

your unit is operating

safely and properly.

Setting Up

Your Snow

Thrower

The extension cord is fastened with a cable tie to the rear

of the auger housing for shipping purposes. Cut the cable

tie and remove it before operating the snow thrower.

CAUTION: Prior to operating your snow thrower, refer

to Auger Control Test on page 11. Read and follow all

instructions carefully, and perform all adjustments

to verify your snow thrower is operating safely and

properly.

Shear Pin Storage (optional)

An area for convenient shear pin storage is located at the

rear of the dash panel.

Drift Cutters (If Equipped)

Drift cutters should be used when operating the snow

thrower in heavy drift conditions.

• Onmodelssoequipped,driftcuttersandhardware

are assembled to the auger housing inverted.

• Removethecarriageboltsandwingnutssecuringthe

drift cutters to the housing.

• Repositiondriftcutterssotheyfaceforwardasshown

in Figure 3-6. Secure with hardware previously

removed, wingnuts should be fastened on the outside

of the housing as shown.

If your unit is not equipped with drift cutters, you may

contact Customer Support as instructed on page 2 for

information regarding price and availability.

Clean-Out Tool

The clean-out tool is mounted to the rear of the auger

housing and is designed to clear a clogged chute. Refer

to page 9 for instructions on how to properly use it.

NOTE: This item is fastened with a cable tie to the rear of

the auger housing at the factory. Cut the cable tie before

operating the snow thrower.

WARNING: Never use your hands to

clean snow and ice from the chute

assembly or auger housing.

Lamp Wiring Harness (If equipped)

The post on the cable tie attaching the lamp wiring har-

ness to the lower handle should be plugged into the hole

in the lower handle. Pull the slack portion of the wiring

harness through the cable tie to prevent interference with

the recoil starter handle. See Figure 3-7.

Skid Shoes

Position the skid shoes based on surface conditions.

Adjust upward for hard-packed snow. Adjust downward

when operating on gravel or crushed rock surfaces. See

“Making Adjustment” Section.

Fig-

ure

Figure 3-6

Figure 3-7

Tire Pressure

The tires are over-inflated for shipping purposes.

Check the tire pressure before operating the snow

thrower. Refer to the tire side wall for tire manufacturer’s

recommended psi and deflate (or inflate) the tires as

necessary.

NOTE: If the tire pressure is not equal in both tires, the

unit may not travel in a straight path and the shave plate

may wear unevenly.

Operating

Your Snow

Thrower

Now that you have set up your snow thrower for opera-

tion, get acquainted with its controls and features. These

are described below and illustrated in Figure 4-1. This

knowledge will allow you to use your new equipment to

its fullest potential.

NOTE: For detailed starting instructions and more

information on all engine controls, refer to the engine

manual packed with your unit.

Shift Lever

The shift lever is located on the right

side of the handle panel. Place the

shift lever into any of eight positions to

control the direction of travel and ground

speed.

Forward

Your snow thrower has six forward (F)

speeds, with position number one (1)

being the slowest speed.

Reverse

Your snow thrower has two reverse (R)

speeds, with position number one (1)

being the slower speed.

Know Your Snow Thrower

Choke Control

The choke control is found on top of the engine and is acti-

vated by rotating the knob counter clockwise. Activating

the choke control closes the choke plate on the carburetor

and aids in starting the engine.

Primer

Depressing the primer forces fuel directly into the engine’s

carburetor to aid in cold-weather starting.

Oil Fill

Engine oil level can be checked and oil added through the

oil fill.

Safety Key

The safety key must be pushed in place in order for the

engine to start. Pull the safety key out to prevent unauthor-

ized use of equipment.

Rocker Switch

The rocker switch is used to stop the engine. The switch

must be in the “ON” position in order to start the engine.

WARNING

Read, understand,

and follow all instruc-

tions and warnings

on the machine and

in this manual before

operating.

Use extreme care

when handling

gasoline. Gasoline is

extremely flammable

and the vapors are

explosive. Never fuel

the machine indoors

or while the engine

is hot or running.

Extinguish cigarettes,

cigars, pipes and

other sources of

ignition.

Figure 4-1

Engine Controls

Recoil Starter

Handle

Choke

Control

Electric Starter

Outlet

Electric Start

Button

Primer

Safety

Key

Rocker

Switch

Oil Fill

Gas Cap

Chute

Assembly

Clean-Out

Tool

Skid Shoe

Augers

Drive Control

Headlight

Auger Control

Shift Lever

Four-Way Chute Control™

Heated Grips (optional)

Wheel Steering

Control

Operating

Your Snow

Thrower

WARNING

The operation of

any snow thrower

can result in foreign

objects being thrown

into the eyes, which

can damage your

eyes severely. Always

wear safety glasses

while operating the

snow thrower, or while

performing any adjust-

ments or repairs on it.

Be sure no one other

than the operator is

standing near the snow

thrower while starting

engine or operating

snow thrower. Never

run engine indoors or

in enclosed, poorly

ventilated areas. En-

gine exhaust contains

carbon monoxide, an

odorless and deadly

gas. Keep hands, feet,

hair and loose clothing

away from any moving

parts on engine and

snow thrower.

Auger Control

The auger control is located on the left handle. Squeeze

the control grip against the handle to engage the augers

and start snow throwing action. Release to stop.

Drive Control/ Auger Control Lock

The drive control is located on the right handle. Squeeze

the control grip against the handle to engage the wheel

drive. Release to stop.

The drive control also locks the auger control so you can

operate the chute directional control without interrupting

the snow throwing process. If the auger control is en-

gaged simultaneously with the drive control, the operator

can release the auger control (on the left handle) and

the augers will remain engaged. Release both controls to

stop the augers and wheel drive.

IMPORTANT: Always release the drive control before

changing speeds.

Heated Handles Switch (If Equipped)

This switch is located on the rear of the snow thrower

dash panel. To activate the heated handles, toggle the

switch to the “ON” position to generate heat within the

handle grips. Toggle the switch to the “OFF” position

after using the snow thrower.

NOTE: The heated handles grips are a compliment to,

not a substitute for, proper cold weather outerwear for

the operator’s hands. It is recommended that the snow

thrower operator wear gloves/mittens to avoid extremities

of winter while operating this equipment.

Augers

When engaged, the augers rotate and draw snow into

the auger housing.

Skid Shoes

Position the skid shoes based on surface conditions.

Adjust upward for hard-packed snow. Adjust downward

when operating on gravel or crushed rock surfaces. See

“Making Adjustment” Section.

Wheel Steering Controls

The left and right wheel steering controls are located on

the underside of the handles. Squeeze the right control to

turn right; squeeze the left control to turn left.

NOTE: Operate the snow thrower in open areas until you

are familiar with these controls.

Chute Clean-Out Tool

The clean-out tool is conveniently fastened to the rear of

the auger housing with a mounting clip.

1. Release both the auger control and the drive/auger

control lock.

2. Stop the engine by pushing the rocker switch to the

“OFF” position, pull out the safety key.

3. Remove the clean-out tool from the mounting clip.

4. Use the shovel-shaped end of the clean-out tool to

remove any snow and ice in the chute assembly.

5. Re-fasten the clean-out tool to the mounting clip on

the rear of the auger housing and restart engine.

6. While standing in the operator’s position (behind the

snow thrower), engage the auger control for a few

seconds to clear any remaining snow or ice from the

chute assembly before continuing to clear snow.

WARNING: Never use your hands to

clean snow and ice from the chute

assembly or auger housing.

Headlight

The headlight is on whenever the engine is running.

!5'%2

#/.42/,

$2)6%

#/.42/,

#(54%$)2%#4)/.!,#/.42/,

#(54%4),4$/7.

#(54%4),450

053("544/.

#(54%2/4!4%

,%&4

053("544/.

#(54%2/4!4%

2)'(4

Four-Way Chute Control™

The chute directional control is located on the left side of

the dash panel.

• Tochangethedirectioninwhichsnowisthrown,

squeeze the button on the joy-stick and pivot the

joy-stick to the right or to the left.

• Tochangetheangle/distancewhichsnowisthrown,

pivot the joy-stick forward or backward.

Gas & Oil Fill-Up

Service the engine with gasoline and oil as instructed in

the separate engine manual packed with your unit. Read

instructions carefully.

Starting The Engine

1. Make certain both the auger control and drive control

are in the disengaged (released) position.

2. Open fuel shut-off valve (If equipped) and make sure

the Rocker switch is in the On position (if equipped).

3. Push in the safety key.

4. Rotate choke control to FULL choke position

(for a cold engine start).

NOTE: If the engine is already warm, place choke control

in the OFF position instead of FULL.

5. Push the primer two times if temperature is above

F (-9

C), four times if temperature is below 15

(-9

C) for cold engine start, making sure to cover vent

hole in the center of the primer when pushing.

NOTE: DO NOT use primer to restart a warm engine

after a short shutdown.

Electric Starter (If Equipped)

1. Determine that your home’s wiring is a three-wire

grounded system. Ask a licensed electrician if you are

not certain.

WARNING: The optional electric starter

is equipped with a grounded three-wire

power cord and plug, and is designed

to operate on 120 volt AC household

current. It must be used with a properly

grounded three-prong receptacle at all

times to avoid the possibility of electric

shock. Follow all instructions carefully

prior to operating the electric starter.

If you have a grounded three-prong receptacle, proceed

as follows:

1. Plug the extension cord into the outlet located on the

engine’s surface. Plug the other end of extension cord

into a three-prong 120-volt, grounded, AC outlet in a

well-ventilated area.

2. Push starter button to start engine.

3. Once the engine starts, immediately release starter

button.

4. As the engine warms, slowly rotate the choke control

to the OFF position . If the engine falters,

quickly rotate the choke control back to FULL and

then slowly into the OFF position again.

5. When disconnecting the extension cord, always unplug

the end at the three-prong wall outlet before unplugging

the opposite end from the snow thrower.

Recoil Starter

1. Grasp the recoil starter handle and slowly pull the rope

out. At the point where it becomes slightly harder to pull

the rope, slowly allow the rope to recoil.

2. Pull the starter handle with a firm, rapid stroke. Do not

release the handle and allow it to snap back. Keep a firm

hold on the starter handle and allow it to slowly recoil.

3. As the engine warms, slowly rotate the choke control to

the OFF position. If the engine falters, quickly rotate the

choke control back to the FULL position and then slowly

into the OFF position again.

NOTE: Allow the engine to warm up for a few minutes

after starting. The engine will not develop full power until it

reaches operating temperatures.

Stopping The Engine

Run engine for a few minutes before stopping to help dry off

any moisture on the engine.

• Pushtherockerswitchtothe“OFF”position.

• Pulloutthesafetykey.

• Closefuelshut-offvalve(Ifequipped).

• Wipeallsnowandmoisturefromtheareaaroundthe

engine as well as the area in and around the drive

control and auger control. Also, engage and release

both controls several times.

To Engage Drive

1. With the engine running near top speed, move

shift lever to one of six FORWARD positions or two

REVERSE positions. Select a speed appropriate for

the snow conditions that exist. Do not shift speeds

while the drive is engaged.

2. Squeeze drive control against the right handle and

the snow thrower will move. Release it and the drive

motion will stop.

3. To turn the unit left or right, squeeze the respective

wheel steering control. See Figure 4-1.

To Engage Augers

1. To engage augers and start snow throwing, squeeze

the left hand auger control against the left handle.

Release to stop augers.

2. While the auger control is engaged, squeeze the drive

control to move, release to stop.Do not shift speeds

while the drive is engaged.

NOTE: This drive lever also locks auger control so you

can turn the chute control without interrupting the snow

throwing process.

3. Release the auger control; the interlock mechanism

should keep the auger control engaged until the drive

control is released.

4. Release the drive control to stop both the augers and

the wheel drive. To stop the auger, both levers must be

released.

WARNING

Read, understand,

and follow all instruc-

tions and warnings

on the machine and

in this manual before

operating.

Use extreme care

when handling

gasoline. Gasoline is

extremely flammable

and the vapors are

explosive. Never fuel

the machine indoors

or while the engine

is hot or running.

Extinguish cigarettes,

cigars, pipes and

other sources of

ignition.

If your home’s wir-

ing system is not a

three-wire grounded

system, do not use

this electric starter

under any conditions.

If your home

electrical system

is grounded, but a

three-hole receptacle

is not available, do

not use your snow

thrower’s electric

starter.

Auger Control Test

Perform the following test before operating your snow

thrower for the first time and at the start of each winter.

Check the adjustment of the auger control as follows:

1. When the auger control is released and in the

disengaged “up” position, the cable should have very

little slack. It should NOT be tight.

2. In a well-ventilated area, start the snow thrower

engine as instructed on the previous page.

3. While standing in the operator’s position (behind the

snow thrower), engage the auger.

4. Allow the auger to remain engaged for approximately

ten (10) seconds before releasing the auger control.

Repeat this several times.

5. With the auger control in the disengaged “up” posi-

tion, walk to the front of the machine.

6. Confirm that the auger has completely stopped

rotating and shows NO signs of motion. If the auger

shows ANY signs of rotating, immediately return to

the operator’s position and shut off the engine. Wait

for ALL moving parts to stop before re-adjusting the

auger control.

7. To readjust the control cable, loosen the upper hex

nut on the auger cable bracket. See Figure 4-2.

8. Position the bracket upward to provide more slack (or

downward to increase cable tension).

9. Retighten the upper hex nut.

10. Repeat Auger Control Test to verify proper adjustment

has been achieved.

General Recommendations

1. Always observe safety rules when performing

any maintenance.

2. The warranty on this snow thrower does not cover

items that have been subjected to operator abuse

or negligence. To receive full value from warranty,

operator must maintain the snow thrower as

instructed here.

3. Some adjustments will have to be made periodically

to maintain your unit properly.

4. Periodically check all fasteners and make sure these

are tight.

When selecting a

Drive Speed, use the

slower speeds until

you are comfortable

and familiar with the

operation of the snow

thrower.

NEVER reposition the

shift lever (change

speeds or direction

of travel) without first

releasing the drive

control and bringing

the snow thrower

to a complete stop.

Doing so will result in

premature wear to the

snow thrower’s drive

system.

WARNING

The muffler, engine

and surrounding

areas become hot

and can cause a burn

150°F (65°C). Do not

touch.

Figure 4-2

Shift Cable

If the full range of speeds (forward and reverse) cannot

be achieved, refer to the figure to the left and adjust the

shift cable as follows:

1. Place the shift lever in the fastest forward speed

position.

2. Loosen the hex nut on the shift cable index bracket.

See Figure 5-1.

3. Pivot the bracket downward to take up slack in the

cable.

4. Retighten the hex nut.

5. Check for correct adjustment before operating the

snow thrower.

Chute Control

Once a season or every 25 hours of operation, whichever

is earlier, check whether the four-way chute control™

cables have slackened. If the chute does not rotate fully,

the chute control cables will have to be adjusted.

To adjust these cables, proceed as follows:

1. To tighten cable, loosen the top nut and tighten the

bottom nut on the cable.

2. Adjust equally on both sides by working on both

cables. See Figure 5-2.

Drive Control & Shift Lever

When the drive control is released and in the disengaged

“up” position, the cable should have very little slack. It

should NOT be tight.

Check the adjustment of the drive control as follows:

1. With the drive control released, push the snow thrower

gently forward. The unit should roll freely.

2. Engage the drive control and gently attempt to push

the snow thrower forward. The wheels should not turn.

The unit should not roll freely.

3. With the drive control released, move the shift lever

back and forth between the R2 position and the F6

position several times. There should be no resistance

in the shift lever.

4. If any of the above tests failed, the drive cable is in

need of adjustment. Proceed as follows:

5. Loosen the lower hex nut on the drive cable bracket.

See Figure 5-3.

6. Position the bracket upward to provide more slack (or

downward to increase cable tension).

7. Retighten the lower hex nut.

WARNING: Run the engine com-

pletely dry of gasoline before tipping

snowthrower.

Making

Adjustments

Figure 5-1

Figure 5-2

WARNING

Read, understand,

and follow all instruc-

tions and warnings

on the machine and

in this manual before

operating.

Never attempt to

make any adjust-

ments while the

engine is running,

except where speci-

fied in operator’s

manual.

Figure 5-3

You can also check the adjustment as follows:

1. With the snow thrower tipped forward, remove the

frame cover underneath the snow thrower by removing

the self-tapping screws. See Figure 6-5 on page 15.

2. With the drive control released, there must be 1/8”

clearance between the friction wheel and the drive

pulley in all positions of the shift lever.

3. With the drive control engaged, the friction wheel must

contact the drive pulley. See Figure 6-8.

4. If adjustment is necessary, loosen the lower hex nut

on the drive cable index bracket and pivot the bracket

upward or downward as necessary. Refer to Figure

5-3. Tighten the lower hex nut to secure the bracket

when correct adjustment is reached.

5. Reassemble the frame cover and return the unit back

to its operating position.

Making

Adjustments

IMPORTANT

It is not recommended

that you operate this

snow thrower on gravel

as loose gravel can be

easily picked up and

thrown by the auger

causing personal injury

or damage to the snow

thrower.

If for some reason,

you have to operate

the snow thrower on

gravel, keep the skid

shoe in the highest

position for maximum

clearance between the

ground and the shave

plate.

Figure 5-4 - Standard Skid Shoe Figure 5-5 - Steel Reversible

Figure 5-6 - Plastic Reversible

Skid Shoes

The space between the skid shoes and the ground can

be adjusted.

• Forclosesnowremovalonasmoothsurface,raise

skid shoes higher on the auger housing.

• Useamiddleorlowerpositionwhentheareatobe

cleared is uneven, such as a gravel driveway.

To adjust the skid shoes:

1. Loosen the four hex nuts (two on each side) and

carriage bolts. Move skid shoes to desired position.

2. Make certain the entire bottom surface of skid shoe

is against the ground to avoid uneven wear on the

skid shoes.

3. Retighten nuts and bolts securely.

NOTE: Some models are equipped with reversible skid

shoes and may be turned over to increase their lifespan.

See Figure 5-6 and 5-7.

Auger Control

To adjust the auger control, refer to page 11.

Maintaining

Your Snow

Thrower

WARNING

Before lubricating,

repairing, or inspect-

ing, disengage all

controls and stop

engine. Wait until all

moving parts have

come to a complete

stop.

Keep all grease and oil

off of the rubber friction

wheel and aluminum

drive plate.

Engine

Refer to the separate engine manual packed with your

unit for all engine maintenance.

Lubrication

Engine

Refer to the separate engine manual packed with your

unit for all engine lubrication instructions.

Gear Shaft

The gear (hex) shaft should be lubricated at least once

a season or after every 25 hours of operation.

WARNING: Run the engine com-

pletely dry of gasoline before tipping

snowthrower.

1. Carefully pivot the snow thrower up and forward so

that it rests on the auger housing.

2. Remove the lower frame cover by removing the

screws which secure it.

3. Apply a light coating of an all-weather multi-purpose

oil to the hex shaft. See Figure 6-1.

NOTE: Avoid getting oil on rubber friction wheel and

aluminum drive plate.

Wheels

At least once a season, remove both wheels. Clean and

coat the axles with a multipurpose automotive grease

before reinstalling wheels.

Auger Shaft

At least once a season, remove the shear pins on auger

shaft. Spray lubricant inside shaft, around the spacers.

Also lubricate the flange bearings found at either end of

the shaft. See Figure 6-2.

Augers

• Theaugersaresecuredtothespiralshaftwith

shear pins and cotter pins. If the auger should strike

a foreign object or ice jam, the snow thrower is

designed so that the pins may shear. Refer to Figure

6-2.

• Iftheaugerswillnotturn,checktoseeifthepins

have sheared. One set of replacement shear pins

has been provided with the snow thrower. When

replacing pins, spray an oil lubricant into shaft before

inserting new pins.

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom of the

snow thrower are subject to wear. They should be

checked periodically and replaced when necessary.

To remove skid shoes:

1. Remove the four carriage bolts and hex flange nuts

which secure them to the snow thrower.

2. Reassemble new skid shoes with the four carriage

bolts (two on each side) and hex flange nuts. Refer

to Figure 6-3.

Figure 6-2

3HEAR0IN

"EARING

3PACERS

Figure 6-3

To remove shave plate:

1. Remove the carriage bolts and hex nuts which attach

it and the skid shoes to the snow thrower housing.

2. Reassemble new shave plate, making sure heads of

carriage bolts are to the inside of housing. Tighten

securely.

Figure 6-1

Maintaining

Your Snow

Thrower

2. Carefully pivot the snow thrower up and forward so

that it rests on the auger housing. Remove the frame

cover from the underside of the snow thrower by

removing four self-tapping screws which secure it.

See Figure 6-5.

3. Roll the auger belt off the engine pulley. See Figure

6-6.

4. a. Loosen and remove the shoulder screw which

acts as a belt keeper. See Figure 6-7.

b. Unhook the support bracket spring from the

frame.

5. Remove the belt from around the auger pulley, and

slip the belt between the support bracket and the

auger pulley. Reassemble auger belt by following

instructions in reverse order. See Figure 6-8.

NOTE: Repeat the auger control test on page 11 before

operating the snowthrower.

NOTE: Do NOT forget to reinstall the shoulder screw

and reconnect the spring to the frame after installing a

replacement auger belt.

NOTE: Although multi-

viscosity oils (5W30,

10W30 etc.) improve

starting in cold weather,

these multi-viscosity

oils also result in higher

oil consumption when

used above 32ºF (0ºC).

Check your snow

thrower’s engine oil

level more frequently to

avoid possible engine

damage from running

low on oil.

IMPORTANT

NEVER replace the

auger shear pins with

standard pins. Any

damage to the auger

gearbox or other com-

ponents, as a result of

doing so, will NOT be

covered by your snow

thrower’s warranty.

Auger Belt Replacement

WARNING: Run the engine com-

pletely dry of gasoline before tipping

snowthrower.

To remove and replace your snow thrower’s auger belt,

proceed as follows:

1. Remove the plastic belt cover on the front of the

engine by removing the two self-tapping screws. See

Figure 6-4.

Figure 6-7

Figure 6-8

Figure 6-4

Figure 6-6

Figure 6-5

Drive Belt Replacement

WARNING: Run the engine com-

pletely dry of gasoline before tipping

snowthrower.

To remove and replace your snow thrower’s auger belt,

proceed as follows:

1. Remove the plastic belt cover on the front of the

engine by removing the two self-tapping screws. See

Figure 6-4.

2 Carefully pivot the snow thrower up and forward so

that it rests on the auger housing. See Figure 6-5.

3. Remove the frame cover from the underside of the

snow thrower by removing four self-tapping screws

which secure it.

4. a. Roll the auger belt off the engine pulley.

b. Use a wrench to pivot the idler pulley toward the

right. See Figure 6-9.

c. Lift the drive belt off engine pulley.

5. Back out the stop screw until the support bracket

rests on the auger pulley. See Figure 6-10.

6. Slip the drive belt off the pulley and between friction

wheel and drive plate. See Figure 6-10.

7. Remove and replace belt in the reverse order.

NOTE: Repeat the drive control adjustment on page 12

before operating the snowthrower.

Friction Wheel Inspection

If the snow thrower fails to drive with the drive control

engaged, and performing the drive control cable adjust-

ment fails to correct the problem, the friction wheel may

need to be replaced.

NOTE: Special tools are required and several com-

ponents must be removed and in order to replace the

snow thrower’s friction wheel rubber. See an authorized

Service Dealer to have the friction wheel rubber

replaced or phone Customer Support as instructed on

page 2 for information on ordering a Service Manual.

To inspect the friction wheel, proceed as follows:

1. Carefully pivot the snow thrower up and forward so

that it rests on the auger housing. See Figure 6-5.

2. Remove the frame cover from the underside of the

snow thrower by removing four self-tapping screws

which secure it. See Figure 6-5.

3. Examine the friction wheel for signs of wear or

cracking. See Figure 6-11.

Off-Season Storage

If unit is to be stored over 30 days, prepare for storage

as instructed in the separate engine manual packed with

your snow thrower.

Clean snow thrower thoroughly.•

Lubricate as instructed in the Maintenance section •

of this manual.

Maintaining

Your Snow

Thrower

NEVER replace the

auger shear pins with

standard hex pins.

Any damage to the

auger gearbox or

other components

as a result of failing

to do so will NOT be

covered by your snow

thrower’s warranty.

Figure 6-9

Figure 6-10

Figure 6-11

Refer to engine manual for correct engine storage •

instructions.

Store the snow thrower in a clean, dry area.•

When storing any type of power equipment in a •

poorly ventilated or metal storage shed, care should

be taken to rustproof the equipment, especially

springs, cables and all moving parts.

NOTE: This section

addresses minor

service issues. For

further details,

contact customer

assistance.

Trouble-

Shooting

CauseProblem Remedy

Engine fails to start

1. Choke not in ON position.

2. Spark plug wire disconnected.

3. Fuel tank empty or stale fuel.

4. Engine not primed.

5. Faulty spark plug.

6. Blocked fuel line.

7. Safety key not in ignition on engine.

8. Fuel shut-ff valve closed. (If Equipped)

1. Move choke to ON position.

2. Connect wire to spark plug.

3. Fill tank with clean, fresh gasoline.

4. Prime engine as instructed in

“Operating Your Snow Thrower”.

5. Clean, adjust gap, or replace.

6. Clean fuel line.

7. Insert key fully into the switch.

8. Open fuel shut-off valve.

Engine runs erratic

1. Move choke lever to OFF position.

2. Clean fuel line; fill tank with clean,

fresh gasoline.

3. Drain fuel tank. Refill with

fresh fuel.

4. Contact Service Center.

1. Unit running on CHOKE.

2. Blocked fuel line or stale fuel.

3. Water or dirt in fuel system.

4. Carburetor out of adjustment.

Engine overheats

1. Contact Service Center.1. Carburetor not adjusted properly.

Loss of power

1. Connect and tighten spark plug

wire.

2. Remove ice and snow from gas

cap. Be certain vent is clear.

3. Contact Service Center.

1. Spark plug wire loose.

2. Gas cap vent plugged.

3. Exhaust port plugged.

Unit fails

to propel itself

1. Adjust drive control cable. Refer to

“Adjustments”.

2. Replace drive belt.

3. Replace friciton wheel.

1. Drive control cable in need of adjust-

ment.

2. Drive belt loose or damaged.

3. Friction wheel worn.

Excessive

Vibration

1. Loose parts or damaged auger.

1. Stop engine immediately and

disconnect spark plug wire. Tighten

all bolts and nuts. If vibration

continues, have unit serviced by a

Service Center.

Unit fails

to discharge snow

1. Stop engine immediately and

disconnect spark plug wire. Clean

chute assembly and inside of

auger housing with clean-out tool

or a stick.

2. Stop engine immediately and

disconnect spark plug wire.

Remove object from auger with

clean-out tool or a stick.

3. Refer to “Auger Control Test” .

4. Refer to Maintenance section.

5. Replace with new shear pin(s).

1. Chute assembly clogged.

2. Foreign object lodged in auger.

3. Auger control cable in need of adjust-

ment.

4. Auger belt loose or damaged.

5. Shear pin(s) sheared.

Warranty

Failure to comply

with suggested

maintenance

and lubrication

specifications will

void warranty.

4 YEAR LIMITED WARRANTY

For FOUR YEARS from the date of retail purchase within Canada, MTD PRODUCTS LIMITED will, at its option, repair

or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship.

This warranty does not cover:

1. Any part which has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper mainte-

nance or alteration; or

2. The unit if it has not been operated and/or maintained in accordance with the owner’s instructions furnished with the

unit; or

3. The engine or motor or component parts thereof which carry separate warranties from their manufacturers. Please

refer to the applicable manufacturer’s warranty on these items; and read engine warranty statement below, or

4. Batteries and normal wear parts except as noted below. Log splitter pumps, valves and cylinders or component parts

thereof are covered by a one year warranty; or

5. Routine maintenance items such as lubricants, filters, blade sharpening and tune-ups, or adjustments such as brake,

clutch or deck; or

6. Normal deterioration of the exterior finish due to use or exposure.

Full Ninety Day Warranty on Battery (if equipped): For ninety (90) days from the date of retail purchase, if any

battery included with this unit proves defective in material or workmanship and our testing determines the battery will

not hold a charge, MTD PRODUCTS LIMITED will replace the battery at no charge to the original purchaser.

Additional Limited Thirty Day Warranty on Battery (if equipped): After ninety (90) days but within one hundred

twenty (120) days from the date of purchase, MTD PRODUCTS LIMITED will replace the defective battery, for the

original purchaser, for a cost of one-half (½) of the current retail price of the battery in effect at the date of return.

Full Ninety Days Warranty on Normal Wear Parts: Normal wear parts are defined as belts, blade adaptors, blades,

grass bags, seats, tires, rider deck wheels and clutch parts (friction wheels). These parts are warranted to the original

purchaser to be free from defects in material and workmanship for a period of ninety (90) days from the date of retail

purchase.

How to Obtain Service: Warranty service is available, with proof of purchase, through your local authorized service

dealer or distributor. If you do not know the dealer or distributor in your area, please call, toll free 1-800-668-1238. The

return of a complete unit will not be accepted by the factory unless prior written permission has been extended by MTD

PRODUCTS LIMITED.

Transportation Charges: Transportation charges for the movement of any power equipment unit or attachment are

the responsibility of the purchaser. Transportation charges for any part submitted for replacement under this warranty

must be paid by the purchaser unless such return is requested in writing by MTD PRODUCTS LIMITED.

Other Warranties: All other warranties, express or implied, including any implied warranty of merchantability is limited

in its duration to that set forth in this express limited warranty. The provisions as set forth in this warranty provide the

sole and exclusive remedy of MTD PRODUCTS LIMITED obligations arising from the sale of its products.

MTD PRODUCTS LIMITED will not be liable for incidental or consequential loss or damage.

4 YEAR LIMITED WARRANTY ENGINES

This limited warranty doubles the time periods of the engine manufacturer’s limited warranty which is enclosed in the

owner’s information package.

12.08.06

Model Wheel As sem bly De scrip tion Tire Rim Axle

Modèle En sem ble de roue De scrip tion Roue Jante Essieu

31AH6WK3 634-04145 16 x 4.8 x 8 LH X-Trac 734-2038 634-04173 738-04168

634-04146 16 x 4.8 x 8 RH X-Trac 734-2038 634-04173

31AH5WLF 634-04145 16 x 4.8 x 8 LH X-Trac 734-2038 634-04173 738-04180

31AH5WL3 634-04146 16 x 4.8 x 8 RH X-Trac 734-2038 634-04173

31AH6ZK4 634-04136 16 x 6.5 x 8 LH X-Trac 734-2031 634-04174 738-04168

634-04137 16 x 6.5 x 8 RH X-Trac 734-2031 634-04174 738-04168

31AH5ZL4 634-04136 16 x 6.5 x 8 LH X-Trac 734-2031 634-04174 738-04180

31AH5ZLG 634-04137 16 x 6.5 x 8 RH X-Trac 734-2031 634-04174 738-04180

31AH5ZQ4

31AH5ZK5

31AM63ED 634-04144A 13 x 4 Snow Hog 734-1732 634-04172A 738-04181

31AH65CG 634-04141 16 x 4.8 Snow Hog 734-1530 634-04173 738-04168

31AH6WKF

31AH6WFF529

31AH6ZFH

31AH6WFF500 634-04142A 15 X 5 Snow Hog 734-1859 634-04172A 738-04168

31AH6ZKG 634-04135 16 X 6.5 Snow Hog 734-1525 634-04174 738-04168

31AH6ZKH

31AM63K2 634-04147A 15 X 5 X 6 LH X-Trac 734-04012 634-04172A 738-04168

634-04148A 15 X 5 X 6 RH X-Trac 634-04172A

31AH5WLE 634-04167A 13 X 4 X 6 LH X-Trac 734-04128 634-04172A 738-04180

31AM53Q2 634-04168A 13 X 4 X 6 RH X-Trac 634-04172A

31AM53L2

5.1.08

AU GER HOUS ING COM PO NENTS/COMPOSANTS DU LOGEMENT DES TARIÈRES

SIZE

TAILLE

AU GER HOUS ING/

LOGEMENT DES

TARIÈRES

AU GER AXLE/

ESSIEU DES

TARIÈRES

SHAVE PLATE

LAME

PLATE

GEAR BOX ASS’Y/

EN SEM BLE DE LA

VIS SANS FIN

SPAC ERS/

ENTRETOISE

WORM GEAR/

ENGRENAGE

684-04266 711-04286 790-00117 618-04170A --- 717-04449

684-04265 711-04285 790-00120 618-04171A 731-04870 (1) 717-04449

684-04264 711-04284 790-00121 618-04172A 731-04870 (2) 717-04449

684-04268 711-04283 790-00118 618-04173A 731-04870 (3) 717-0528A

684-04267 711-04282 790-00119 618-04165A 731-04871 (2) 717-0528A

32 71

18B

669

26 27

18A

42A

42E

42B

42C

42F

42D

42H

42G

43A

43B

Optional/en option

La page charge ...

Bolens 31AH5ZLH565 Le manuel du propriétaire

Marque: Bolens

Modèle: 31AH5ZLH565

Catégorie: Souffleuses à neige

Taper: Le manuel du propriétaire

Ce manuel convient également à

31AH5WLF565

Télécharger le PDF

rapport

dans d''autres langues

English: Bolens 31AH5ZLH565 Owner's manual

Bolens 31AH5ZLH565 Le manuel du propriétaire

Ce manuel convient également à

Bolens 31AH5ZLH565 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents