Honeywell L8130A1005 7-Day Programmable Thermostat Manuel utilisateur

Owner’s Guide

TL8130A1005

7-Day Programmable Thermostat

69-1805EF-07

Overview

Before you start..................................................1

About your thermostat........................................2

Controls..............................................................3

Display ...............................................................4

Installation

Installing the thermostat.....................................5

Wiring diagram ...................................................6

Setting the configuration switches......................7

Setup

Time and day......................................................8

Daylight Saving Time .........................................9

Preset temperatures.........................................10

Default schedule ..............................................11

Modifying the schedule ....................................12

Operation

Running the schedule (Automatic mode) .........13

Temporary override of schedule.......................13

Permanent override (Manual mode) ...............14

Appendices

Error messages................................................15

Technical specifications....................................16

Warranty...........................................................17

Customer assistance........................................18

Table of contents

TL8130A1005

1

Read the entire document

CAUTION:

• Installation must be carried out by a certified electrician and must comply with national and local

electrical codes.

• To prevent severe shock or electrocution, always cut the power at the service panel before working

with wiring.

• Use this thermostat for resistive loads only.

• Do NOT install the thermostat in an area where it can be exposed to water or rain.

• Avoid locations where there are air drafts (top of staircase, air outlet), dead air spots (behind a

door), direct sunlight or concealed chimney or stove pipes.

• For a new installation, choose a location about 1.5 m (5 ft.) above the floor.

• Install the thermostat on an inside wall facing the heating system.

• Install the thermostat onto an electrical box.

• Use special CO/ALR solderless connectors if you connect the thermostat to aluminum wires.

• Keep the thermostat's top and bottom air vents (openings) clean and unobstructed at all times.

Before you start

Owner’s Guide

2

Honeywell Home’s TL8130A1005 thermostat can be connected to an electric

heater to control the room temperature.

Supplied Parts

• One (1) thermostat

• Two (2) mounting screws

• Four (4) solderless connectors for copper wires

About your thermostat

TL8130A1005

3

Controls

On/Standby switch*

Day button

Temperature adjustment buttons**

Program button

Mode selection / program exit

Preset temperature buttons

(see page 10)

Backlight button**

Program clear button

Hour button

Minutes button

*

Place at Standby to cut power to the heater (e.g., in the summer). This will not affect the time and temperature settings.

** When the backlight button or either of the buttons is pressed, the display illuminates for 12 seconds.

Owner’s Guide

4

Display

Temperature*

Operation mode icon

(see pages 13 & 14)

Period (see page 11)

Time

Number of flames varies

according to heating intensity

Preset temperature icon (see page 10)

Appears when the setpoint

temperature is displayed*

Indicates this thermostat model is used

to control the ambient temperature

Day

* The thermostat normally displays the actual (measured) temperature. To view the setpoint temperature, briefly press

either of the buttons. The setpoint will appear for 5 seconds. To change the setpoint temperature, press one of the

buttons until the desired temperature is displayed. To scroll faster, press and hold the button.

TL8130A1005

5

1) Turn the heating system off at the main electrical panel.

2) Loosen the bottom screw and remove the thermostat faceplate

from its wallplate. (The screw cannot be completely removed.)

3) Connect the thermostat to the load and to the power supply

(see page 6).

4) Install the wallplate to the electrical box using the provided

screws.

5) If necessary, set the configuration switches on the back of the

faceplate (see page 7).

6) Install the faceplate back on the wallplate and tighten the

screw. If there is a sticker on the screen, peel it off.

7) You can now return power to the heating system at the main

electrical panel.

Installing the thermostat

Wallplate

Faceplate

Owner’s Guide

6

NOTE: Connect the wires using the provided solderless connectors for copper wires.

Wiring diagram

Power

Load

TL8130A1005

7

Configuration switches are on the back of the faceplate.

Set the configuration switches

# Configurations Up Down

1 Display format °F / 12 h °C / 24 h

2Early Start1

1. Early Start is used in Automatic mode only. When Early Start is enabled (on), the thermostat

determines when to start heating so the Comfort temperature is attained at the beginning of

periods 1 and 3. When Early Start is disabled (off), heating starts only at the beginning of

periods 1 and 3; thus there is a delay before the Comfort temperature is reached.

Enable Disable

3 Not used

Owner’s Guide

8

To set the clock and the day:

1) Press the Hour button to set the hour.

2) Press the Min button to set the minutes.

3) Press the Day button to set the day.

4) Press the Mode/Ret button to return the thermostat to normal display.

NOTE: The thermostat will automatically return to normal display if no button is

pressed for 60 seconds.

Time and day

TL8130A1005

9

When the Daylight Saving Time function is enabled (On), the thermostat automatically switches to Daylight

Saving Time on the second Sunday of March and to normal time on the first Sunday of November.

NOTE: The Daylight Saving Time function is disabled (default setting) when the clock loses its setting.

To set the

Daylight Saving Time function and to set the date:

1) Press the Day button (3 seconds) until DLS appears on the screen.

2) Press either of the buttons to toggle between On (enabled) and Off (disabled).

3) Press the Day button briefly. The year setting is displayed.

4) Press either of the buttons to set the current year.

5) Press the Day button briefly. The month setting is displayed.

6) Press either of the buttons to set the current month.

7) Press the Day button briefly. The date setting is displayed.

8) Press either of the buttons to set the current date.

9) Press the Mode/Ret button to return the thermostat to normal display.

NOTE: The thermostat will automatically return to normal display if no button is pressed for 60 seconds.

Daylight Saving Time

Owner’s Guide

10

The thermostat has 3 preset temperatures. Their default settings are shown in the following table.

To use a preset temperature:

Briefly press the appropriate preset temperature button ( , or ). The preset temperature will

become the current setpoint and its icon will appear on the screen.

To modify a preset temperature:

1) Press one of the buttons to display the desired temperature.

2) Press and hold the appropriate preset temperature button ( , or ) until its icon is displayed.

Preset temperatures

Preset temperature Intended use Icon Default setting

Comfort When at home 21.0°C (70°F)

Economy When asleep or away from home 16.5°C (62°F)

Vacation During prolonged absence 10.0°C (50°F)

TL8130A1005

11

The schedule consists of 4 periods per day, which represents a typical work day. The Comfort ( ) preset

temperature is automatically used in Periods 1 and 3 and the Economy ( ) preset temperature in Periods

2 and 4. You can program the thermostat to skip (cancel) the periods that do not apply to your situation. For

example, you can skip periods 2 and 3 for the weekend.

NOTE: If you wish to use only 2 periods, use the following combinations: “1 and 4” or “2 and 3”. Early Start

(see page 9) will not work with any other combinations.

You can have a different program every day; i.e., each period can start at a different time every day. The

thermostat has been programmed with the following schedule.

Default schedule

Period Description Setting MO TU WE TH FR SA SU

Wake Comfort 6:00 AM 6:00 AM 6:00 AM 6:00 AM 6:00 AM 6:00 AM 6:00 AM

Leave Economy 8:00 AM 8:00 AM 8:00 AM 8:00 AM 8:00 AM --:-- --:--

Return Comfort 6:00 PM 6:00 PM 6:00 PM 6:00 PM 6:00 PM --:-- --:--

Sleep Economy 10:00 PM 10:00 PM 10:00 PM 10:00 PM 10:00 PM 10:00 PM 10:00 PM

Owner’s Guide

12

1) Press Pgm. Period 1 for Monday is displayed.

2) To program another period, press Pgm to display that period.

3) To program another day, press Day to display that day (hold for 3 seconds to

select the entire week).

4) Press Hour and Min to set the period start time, or press Clear to skip

(cancel) the period (--:-- will be displayed).

5) Repeat steps 2 to 4 to program another period.

6) Press Mode/Ret to return the thermostat to normal display.

NOTE: The thermostat will automatically return to normal display if no button is

pressed for 60 seconds.

Modifying the schedule

TL8130A1005

13

In Automatic mode, the thermostat follows the programmed schedule (see

page 11). To place the thermostat in this mode, press Mode/Ret until is

displayed.

If you modify the setpoint temperature (by pressing the , or button) when

the thermostat is in Automatic mode, the new temperature will be used until the

beginning of the next period. flashes during the temporary override. You can

cancel the temporary override by pressing Mode/Ret.

Running the schedule (Automatic mode)

Temporary override of schedule

Owner’s Guide

14

To place the thermostat in Manual mode, press Mode/Ret to display on the

screen. In this mode, the thermostat does not follow the programmed schedule.

Press the , or button to set the temperature.

Permanent override of schedule (Manual mode)

TL8130A1005

15

The measured temperature is below the display range. Heating is

activated.

The measured temperature is above the display range. Heating is

deactivated.

Verify the thermostat connection and sensor connection.

Error Messages

Owner’s Guide

16

Power supply: 240/208 VAC, 50/60 Hz

Maximum load: 16.7 A (4000 W @ 240 VAC)

(3470 W @ 208 VAC)

Heating cycle: 15 minutes

Setpoint range: 5 °C to 30 °C (40 °F to 86 °F)

Display range: 0 °C to 70 °C (32 °F to 158 °F)

Resolution: 0.5 °C (1 °F)

Data protection: In the event of a power failure, most settings are saved.

However the time and Daylight Saving Time must be set if the power failure lasts

more than 6 hours. The thermostat will return to the mode that was active prior to

the power failure.

Technical Specifications

Energy Verified

Only

TL8130A1005

17

Resideo warrants this product, excluding battery, to be free from defects in workmanship or materials, under normal use and service, for a period of

five (5) years from the date of first purchase by the original purchaser. If at any time during the warranty period the product is determined to be

defective due to workmanship or materials, Resideo shall repair or replace it (at Resideo’s option).

If the product is defective,

(i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or

(ii) call Resideo Customer Care at 1-800-468-1502. Customer Care will make the determination whether the product should be returned to the

following address: Resideo Return Goods, 1985 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Resideo that the defect was caused by

damage which occurred while the product was in the possession of a consumer.

Resideo’s sole responsibility shall be to repair or replace the product within the terms stated above. RESIDEO SHALL NOT BE LIABLE FOR ANY

LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR

INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY RESIDEO MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED

WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY

LIMITED TO THE FIVE YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so

the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you have any questions concerning this

warranty, please write Resideo Customer Care, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502.

Warranty

Owner’s Guide

18

If you have any questions about the operation of your thermostat, please go to

www.honeywellhome.com.

Customer assistance

The Honeywell Home trademark is used under license from Honeywell International, Inc.

This product is manufactured by Resideo Technologies, Inc. and its affiliates.

Resideo Technologies, Inc. et ses sociétés affiliées.

www.resideo.com

Resideo Technologies, Inc.

1985 Douglas Drive North, Golden Valley, MN 55422

69-1805EF—07 M.S. Rev. 10-21 | Printed in United States | Imprimé aux États-Unis

La page charge ...

Honeywell L8130A1005 7-Day Programmable Thermostat Manuel utilisateur

Honeywell L8130A1005 7-Day Programmable Thermostat Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents