Omega HH-2100 Series Manuel utilisateur
- Catégorie
- Mesure, test
- Taper
- Manuel utilisateur
Ce manuel convient également à
La page charge ...
Il se peut que certaines options décrites ne s’appliquent
pas à votre appareil. Veuillez vérifier les fonctions de votre
appareil avant de continuer.
ATTENTION: Ne pas mettre la sonde en contact avec une
surface connectée à un voltage hasardeux (un voltage de
plus de 30V RMS ou 42.4V charge maximum). Assurez-
vous que la sonde corresponde à ce que vous voulez
mesurer, en faisant attention à la gamme de mesures et au
type de thermocouple. Insérer la prise de la sonde dans la
fiche qui se trouve sur l’appareil.
REMARQUE: seules les sondes figurant sur la liste doivent
être utilisées avec la gamme de thermomètres de série
HH2100.
(Excepté le HH2146T)
Appuyez continuellement sur la touche .
ÉCLAIRAGE
ON
X
Y
l’appareil a été réglé sur °C ou °F en usine
Fonction disponible
Veuillez vous référer au verso de l’appareil pour la gamme
de mesures.
UTILISATION DE L’APPAREIL
PILES
NIVEAU IP67
METTRE EN MARCHE
ON
OFF
2 piles AA ou équivalent. Veuillez vous référer au verso de
l’appareil pour changer/remplacer les piles.
Quand s’allume les piles ont besoin d’être changées.
Le niveau d’étanchéité de ce produit ne sera pas conservé à
moins que les vis du compartiment batterie soient fortement
serrées quand on insère ou remplace les batteries.
Appuyez sur le bouton pour mettre l’appareil en marche
et sur le bouton pour l’arrêter. L’appareil s’arrête
automatiquement après 12 minutes. Si vous appuyez
continuellement sur la touche quand l’appareil est mis en
marche l’arrêt automatique sera immobilisé jusqu’à ce que
l’appareil soit arrêté.
CONNECTER LA SONDE
Les sondes suivantes doivent être utilisées avec les
thermomètres de série HH2100.
F
Alcune delle opzioni descritte potrebbero non essere
valide nell’ambito di questo strumento. Prima di
procedere, controllare le funzioni dello strumento che
avete acquistato.
INTERRUZIONE DISPLAY
Premendo il tasto si ferma il display ed il simbolo
appare sul display. Premere il tasto di nuovo per ritornare
al display normale.
X
Y
Lo strumento viene venduto predisposto a °C oppure °F
Funzione disponibile
Riferirsi alla parte posteriore per i campi di temperatura.
FUNZIONAMENTO DELLO STRUMENTO
BATTERIE
VALUTAZIONE IP67
ON - OFF
ON OFF
Due batterie di tipo AA o elementi equivaleneti. Per
montaggio e sostituzione seguire le istruzioni sul retro dello
strumento. Quando il simbolo appare sul display,
sostituire le batterie.
La valutazione di impermeabilitá di questo produtio non sará
mantenuta a meno che le vite che mantengono il
compatimento delle batterie sono strette saldamento quando
si inseriscono o si sostituiscono le batterie.
Premere il tasto per attivare ed il tasto per
disattivare. Disinserimento automatico dopo 12 minuti. Il
tasto viene conservato quando l’apparecchio è acceso,
la funzione di disinserimento automatico viene disattivata
quando l’apparecchio viene spento.
SONDE
Con i Termometri di Serie HH2100 sono da usare le sonde
seguenti.
AVVERTENZA - Evitare il contatto della sonda con qualsiasi
servizio collegato a voltaggi pericolosi (per esempio un
voltaggio superiore ai 30 volt RMS o 42,4 volt di cresta con
riferimento sia a collegamenti terra che di massa.
Assicuratevi che la sonda sia idonea all’applicazione,
prestando particolare attenzione alla portata della
temperatura ed il tipo di termocoppia. Collegare la spina di
attacco alla presa sulla parte superiore dello strumento.
NOTA: Con la gamma di Termometri Serie HH2100
andrebbero usate solo le sonde elencate.
(eccetto per il modello HH2146T)
Premere il tasto mantenendolo premuto.
RETROILLUMINAZIONE
ON
DISPLAY
BATTERIA
VELOCE
SI
SELEZIONE CANALE
CENTI-
GRADO
CAL
FAHRENHEIT
REGIST-
RAZIONE
ORARIO HH:MM
INCONVENIENTE
NUMERICO
IMMISSIONE
PORTATA
INCONVENIENTE
INCONVENIENTE
INSERIRE
NS
NE NS
Cal
OK? A-B
A/R
°°CF
I
AFFICHAGE
MAINTIEN DE L’AFFICHAGE
Pour maintenir l’affichage appuyez sur le bouton . est
affiché. Appuyez à nouveau sur le bouton pour retourner
en mode normal.
PILE ENTRER
LE SÉLECTEUR
DE CANAUX
CELCIUS
CAL
FAHRENHEIT
ENREGISTRER
L’HEURE
LES MULTIFONCTIONS LES MULTIFONCTIONS
LES MULTIFONCTIONS
L’ENTRÉE
NUMÉRIQUE
LA GAMME
DE MESURES
FAST
NS
NE NS
Cal
OK? A-B
A/R
°°CF
INDICATION RUPTURE DE CIRCUIT CAPTEUR OU AU-
DESSUS/AU- DESSOUS DE L’AUTONOMIE
O-C
HH2106T
HH2146T
SPECIFICATIONS COMMUNES
CALIBRAGE DE L’INSTRUMENT
Si le capteur a une rupture de circuit est visualisé sur
l’afficheur. Si la température est au-dessus/au-dessous de
l’autonomie clignote sur l’afficheur.
Dimensions: 155 x 67 x 40mm
Poids: 180g
Veuillez remarquer que la gamme de thermomètres de série
HH2100 ne peut être calibrée que par un centre de services
Omega. Pour des précisions concernant le centre le plus
proche de chez vous, veuillez vous reporter à la finde ces
consignes d’utilisation.
PRÉCISION
Modèles
Modèles
La précision pour chaque appareil est de ±1 digit.
±0.2°C/0.4°F de -20°C to +70°C/-4°F à +158°F
±0.1% de la lecture ±0.2°C/0.4°F autrement
±0.2% de la lecture ±0.1°C/0.2°F de -150°C à +800°C/
-238°F à +1472°F
SENSORE A CIRCUITO APERTO O INDICAZIONE DI
ECCESSIVA O INSUFFICIENTE PORTATA
O-C
HH2106T
HH2146T
SPECIFICA TECNICA
CALIBRATURA STRUMENTO
Se il sensore è circuito aperto, sul display apparirà fino
a che la condizione sussiste.
Dimensioni: 155 x 67 x 40mm
Peso: 180g
Nota: La gamma di termometri di serie HH2100 può essere
calibrata solo da Centri di Servizio omega. Per dettagli sul
centro più vicino, confrontare la parte finale di queste
istruzioni di funzionamento.
QUESTO STRUMENTE SOMO APPROVATI
Dotato
Dotato
All ±1 digit.
±0.2°C/0.4°F over range -20°C to +70°C/-4°F to +158°F
±0.1% rdg ±0.2°C/0.4°F elsewhere
±0.2% rdg ±0.1°C/0.2°F over range -150°C to +800°C/
-238°F to +1472°F
Il rendimento complessivo dello strumento é ottenuto dalla combinazione dell'indubbia
precisione e dell'assenza di inaccuratezza nel procedimento di misurazione.
La performance générale de l'instrument peut être vérifiée en combinant les mesures de
précision ci-dessus et les incertitudes liées à l'opération de mesure.
®
®
omega.com
OMEGAnet On-Line Service
http://www.omega.com
®
Internet e-mail
Servicing North America:
For immediate technical or application assistance:
Servicing Europe:
USA:
ISO 9001 Certified
Canada:
USA and Canada:
Mexico and
Latin America:
Benelux: Postbus 8034, 1180 LA Amstelveen, The Netherlands
Tel: (31) 20 6418405
Toll Free in benelux: 0 800 0993344
e-mail: [email protected]
Czech Republic:
France:
Germany/Austria:
United Kingdom:
ISO 9002 Certified
One Omega Drive, River Bend Technology Centre,
Northbank, Irlam, Manchester M44 5EX, England
Tel: 44 (161) 777-7711
Toll Free in England: 0800-488-488
e-mail: [email protected]
Daimlerstrasse 26, D-85392 Deckenpfronn, Germany
Tel: 49 (07056) 3017
Toll Free in German: 0130 11 21 66
e-mail: [email protected]
9 rue Denis Papin, 78190 Trappes
Tel: (33) 130-621-400
Toll Free in France: 0800-4-06342
e-mail: [email protected]
ul. Rude armady 1868, 73301 Karvina-Hranice
Tel: 420 (69) 6311899
Toll Free: 0800-1-66342
Sales Service:1-800-826-6342 / 1-800-TC-OMEGA
Customer Service: 1-800-622-2378 / 1-800-622-BEST
Engineering Service: 1-800-872-9436/1-800-USA-WHEN
TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA
SM
SM
SM
Tel: (95) 800-826-6342
En Español: (95) 203-359-7803
FAX: (95) 203-359-89-8
Email: [email protected]
FAX: (31) 20 6434643
FAX: 420 (69) 6311114
Email: [email protected]
FAX: (33) 130-699-120
FAX: 49 (07056) 8540
FAX: 44 (161) 777-6622
976 Bergar
Laval (Quebec) H7L 5A2
Tel: (514) 856-6928
e-mail: [email protected]
One Omega Drive, Box 4047
Stamford, CT 06907-0047
Tel: (203) 359-1660
e-mail: [email protected]
FAX: (203) 359-7700
FAX: (514) 856 6886
WARRANTY / DISCLAIMER
RETURN REQUESTS / INQUIRIES
OMEGA ENGINEERING, INC warrants this unit to be free of defects in materials and
workmanship for a period of 25 months from the date of purchase. OMEGA Warranty
adds an additional one (1) month grace period to the normal one (1) year product
warranty to cover handling and shipping time. This ensures that OMEGA’S customers
receive maximum coverage on each product. If the unit malfunctions, it must be returned
to the factory for evaluation. OMEGA’s Customer Service Depart-ment will issue an
Authorized Return (AR) number immediately upon phone or written request. Upon
examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced
at no charge. OMEGA’S WARRANTY does not apply to defects resulting from any action
of the purchaser, including but not limited to mishandling, improper interfacing, operation
outside of design limits, improper repair, or unauthorized modification. This WARRANTY
is VOID if the unit shows evidence of having been tampered with or shows evidence of
having been damaged as a result of excessive corrosion; or current, heat, moisture or
vibration; improper specification; misapplication; misuse or other operating conditions
outside of OMEGA’s control. Components which wear are not warranted, including but
not limited to contact points, fuses, and triacs. OMEGA is pleased to offer suggestions
on the use of its various products. However, OMEGA neither assumes responsibility for
any omissions or errors nor assumes liability for any damages that result from the use if
its products in accordance with information provided by OMEGA, either verbal or written.
OMEGA warrants only that the parts manufactured by it will be as specified and free of
defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF
ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, EXCEPT THAT OF TITLE, AND
ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANT-ABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DIS-CLAIMED.
LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive,
and the total liability of OMEGA with respect to this order, whether based on contract,
warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the
purchase price of the component upon which liability is based. In no event shall OMEGA
be liable for consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be
used: (1) as a “Basic Component” under 10 CFR 21 (NRC), used in or with any nuclear
installation or activity; or (2) in medical applications or used on humans. Should any
Product(s) be used in or with any nuclear installation or activity, medical application, used
on humans, or misused in any way, OMEGA assumes no responsibility as set forth in our
basic WARRANTY / DISCLAIMER language, and, additionally, purchaser will indemnify
OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out
of the use of the Product(s) in such a manner.
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service
Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER
MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S
CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS).
The assigned AR number should then be marked on the outside of the return package an
on any correspondence.
FOR WARRANTY RETURNS For NON-WARRANTY REPAIRS,
please have the following information consult OMEGA for current repair
available BEFORE contacting OMEGA: charges. Have the following information
1. Purchase Order number under which available BEFORE contacting OMEGA:
the product was PURCHASED, 1. Purchase Order number to cover the
2. Model and serial number of the COST of the repair/calibration
product under warranty, and 2. Model and serial number of the
3. Repair instructions and/or specific product, and
problems relative to the product. 3. Repair instructions and/or specific
problems relative to the product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible.
This affords our customers the latest in technology and engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 1998 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied,
photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form, in
whole or in part, without the prior written consent of OMEGA ENGINEERING, INC. It is the policy of
OMEGA to comply with all worldwide safety and EMC / EMI regulations that apply. OMEGA is constantly
pursuing certification of its products to the European New Approach Directive. OMEGA will add the CE
mark to every appropriate device upon certification. The information contained in this document is believed
to be correct, but OMEGA Engineering, Inc. accepts no liability for any errors it contains, and reserves the
right to alter the specifications without notice. WARNING: These products are not designed for use in, and
should not be used for, patient connected applications.
Y
ThermistanceT
X
Y
Modèle
HH2106T HH2146T
Capteur
C/F
Hold
X
Y
ThemistorT
X
Y
Modello
HH2106T HH2146T
Capteur
C/F
Arresto
X
Code de sonde THX-HH2146T THX-HH2106T
Type de capteur Thermistence T
Dimensions des extrémités 120mm x 3.3mm 90mm x 3.3mm
Longueur de manche 143mm 143mm
Unités utilisées avec HH2146T HH2106T
Codice Sonda THX-HH2146T THX-HH2106T
Tipo di Sensore Termistore T
Dimensioni della Punta 120mm x 3.3mm 90mm x 3.3mm
Lunghezza Impugnatura 143mm 143mm
Unità usata con HH2146T HH2106T
BROWN +VE
THERMISTOR
FANWAL PART No. 194-22-LNS-CO1
R.T. CURVE 2252 0Hms @ 25°C
TYPE ‘T’ THERMOCOUPLE
CONNECTION POINTS
WHITE -VE
THERMISTOR
THX-HH2106T
THX-HH2146T
THERMISTOR PROBE
CONNECTION POINTS
(NO POLARITY)
BROWN +VE
THERMISTOR
FANWAL PART No. 194-22-LNS-CO1
R.T. CURVE 2252 0Hms @ 25°C
TYPE ‘T’ THERMOCOUPLE
CONNECTION POINTS
WHITE -VE
THERMISTOR
THX-HH2106T
THX-HH2146T
THERMISTOR PROBE
CONNECTION POINTS
(NO POLARITY)
-
1
-
2
Omega HH-2100 Series Manuel utilisateur
- Catégorie
- Mesure, test
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Omega HH-2100 Series User manual
- español: Omega HH-2100 Series Manual de usuario
- Deutsch: Omega HH-2100 Series Benutzerhandbuch
Documents connexes
-
Omega HH-2000 Series Le manuel du propriétaire
-
-
-
-
-
-
-
Omega Engineering HCTB-3040 Manuel utilisateur
-
-
Omega Vehicle Security HHP-2000 Series Manuel utilisateur