Breville the All in One Manuel utilisateur

Catégorie
Robots culinaires
Taper
Manuel utilisateur
the All In One
Instruction Book - BSB530XL
BSB530XL_IB_C16.indd 1 7/11/2016 1:45 PM
2
BREVILLE
RECOMMENDS
SAFETY FIRST
At Breville we are very safety
conscious. We design and
manufacture consumer
products with the safety of you,
our valued customer, foremost
in mind. In addition we ask
that you exercise a degree of
care when using any electrical
appliance and adhere to the
following precautions.
IMPORTANT
SAFEGUARDS
READ ALL
INSTRUCTIONS BEFORE
USE AND SAVE FOR
FUTURE REFERENCE
Remove any packaging
material and promotional
stickers before using the
immersion blender for the
first time.
Do not place the
immersion blender near
the edge of a counter-top
or table during operation.
Ensure the surface is level,
clean and free of water,
flour, etc.
When mixing liquids,
especially hot liquids with
the immersion blender
use a tall container or
blend small quantities at a
time to reduce spillage.
Do not place the
immersion blender on or
near a hot gas or electric
burner, or where it could
touch a heated oven.
2 Breville recommends safety first
8 Components
9 Functions
18 Care & Cleaning
20 Troubleshooting
21 Food preparation guide
23 French
Contents
BSB530XL_IB_C16.indd 2 7/11/2016 1:45 PM
3
If using the immersion
blender to blend hot food
in a saucepan over heat,
remove the saucepan
from the heat source and
ensure the power cord and
body of appliance are also
kept away from any heat
source.
Blades are sharp. Handle
carefully.
Take care when handling
the immersion blender,
attachments and sharp
cutting blades, when
emptying the bowl
and during cleaning.
Remember the blades
and attachments are
very sharp and should be
kept out of the reach of
children.
Always make sure the
immersion blender is
completely and properly
assembled before
operating.
Ensure the immersion
blender is turned off and
the cord is unplugged
from the power outlet
before attempting
to attach any of the
accessories.
Do not use attachments
other than those provided
with the immersion
blender.
Do not use the whisk
attachment for anything
other than its intended
use.
Do not attempt to operate
the immersion blender
by any method other than
those described in this
booklet.
Do not process hot or
boiling liquids in food
processor bowl – allow
liquids to cool before
placing into the food
processor bowl.
Do not operate the
appliance continuously for
more than 1 minute. Allow
the motor to rest for 1
minute between each use.
BSB530XL_IB_C16.indd 3 7/11/2016 1:45 PM
4
Never mix dry, thick or
heavy mixtures for more
than 30 seconds. Stop
the operation and stir
the ingredients before
continuing. Allow the
motor to rest for
1 minute between each
use.
When using heavy loads,
the appliance should not
be operated for more than
30 seconds.
Keep hands and utensils
out of the container while
blending to prevent the
possibility of severe injury
to persons or damage to
the unit. A spatula may
be used but must be used
only when the unit is not
running.
Always ensure the
immersion blender is
turned off and the cord
is unplugged from the
power outlet before
attempting to move the
appliance, when not in
use, if left unattended and
before disassembling,
cleaning or storing.
Always assemble
processing bowl
lid and insure it is locked
into place before use.
If food becomes lodged
around the processing
blades or in the blade
guard, release the trigger
switch and unplug the
cord. Use a spatula to
dislodge the food. Do not
use fingers as the blades
are sharp.
Do not remove the
immersion blender
from ingredients during
operation. Ensure the
appliance is off and has
stopped before removing,
to avoid contact with
moving blades or whisk.
While processing food to
reduce the risk of severe
injury to persons or
damage to the appliance a
spatula may be used, but
must be used only when
the food processor is not
running.
BSB530XL_IB_C16.indd 4 7/11/2016 1:45 PM
5
Do not leave the
immersion blender
unattended when in use.
To protect against electric
shock do not immerse the
motor body, cord or power
plug in water or any other
liquid.
Keep the appliance clean.
Follow the cleaning
instructions provided in
this book.
Do not use the immersion
blender with wet hands.
Do not push food into
the feed chute with your
fingers or other utensils.
Always use the food
pusher provided.
Keep fingers, hands,
knives and other utensils
away from moving blade
and discs.
Do not place hands or
fingers in the processing
bowl of the food
processor unless the
motor, processing blades
or disc have come to a
complete stop. Ensure
the trigger switch has
been released to turn the
motor off and the power
cord is unplugged from
the power outlet before
removing the lid from the
processing bowl.
The BSB530XL includes
several attachments. The
rating for this appliance is
based on the immersion
blending leg and food
processor attachments
which draw the greatest
load. Other included
attachments may draw
significantly less load
during their use.
BSB530XL_IB_C16.indd 5 7/11/2016 1:45 PM
6
The appliance is also
fitted with a polarised
plug (one blade is wider
than the other). To reduce
the risk of electric shock
this plug will fit in a
polarised outlet only one
way. If the plug does not
fit, contact a qualified
electrician. Do not modify
the plug in any way.
IMPORTANT
SAFEGUARDS
FOR ALL
ELECTRICAL
APPLIANCES
Unwind the cord fully
before use.
This appliance has a
polarized plug (one blade
is wider than the other).
To reduce the risk of
electric shock, this plug
will fit in a polarized outlet
only one way. If the plug
does not fit fully in the
outlet, reverse the plug. If
it still does not fit, contact
a qualified electrician.
Do not modify the plug in
any way.
Do not let the cord
hang over the edge of a
table or counter, touch
hot surfaces or become
knotted.
This appliance is not
intended for use by young
children or infirm persons
without supervision.
Young children should be
supervised
to ensure that they do not
play with
the appliance.
It is recommended to
regularly inspect the
appliance. Do not use the
appliance if power supply
cord, plug or appliance
becomes damaged in
any way. Call Breville
Consumer Support for
examination, adjustment
and/or repair.
For any maintenance
other than cleaning,
call Breville Consumer
Support.
BSB530XL_IB_C16.indd 6 7/11/2016 1:45 PM
7
This appliance is for
household use only. Do
not use this appliance
for anything other than
its intended use. Do not
use in moving vehicles
or boats. Do not use
outdoors.
BREVILLE ASSIST
®
PLUG
Your Breville appliance
comes with a unique
Assist
®
Plug, conveniently
designed with a finger hole
to ease removal from the
power outlet.
SHORT CORD
INSTRUCTIONS
Your Breville appliance
is fitted with a short
power supply cord to
reduce personal injury or
property damage resulting
from pulling, tripping or
becoming entangled with a
longer cord.
If an extension cord is
used, (1) the marked
electrical rating of the
cord set or extension cord
should be at least as great
as the electrical rating of
the appliance, (2) the cord
should be arranged so
that it will not drape over
the countertop or table-
top where it can be pulled
on by children or tripped
over unintentionally and
(3) the extension cord
must include a 3-prong
grounding plug.
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
BSB530XL_IB_C16.indd 7 7/11/2016 1:45 PM
8
Components
A. Speed Control Dial
B. Easy Grip Trigger Switch
C. Motor Body
D. Processing Gear Box
E. Processing Bowl Lid
F. 6 Cup (1.6L) Processing Bowl
G. Food Pusher & Feed Chute
H. Whisk
I. Stainless Steel Blending Leg
J. Variable Mashing Leg
K. Micro-serrated S Blade™
L. Adjustable Slicing Disc
M. Reversible Shredding Disc
N. Storage Base
O. Spindle
NOT SHOWN
Blade Covers
C
E
D
F
IJ
H
K
G
B
A
L
N
M
O
BSB530XL_IB_C16.indd 8 7/11/2016 1:45 PM
9
Functions
BEFORE FIRST USE
Remove any packaging material and
promotional labels. Remove the blending
leg and wash it in warm soapy water (refer to
assembly instructions in this booklet). Rinse
and dry thoroughly.
Ensure no water remains inside the blending
leg to avoid water running into the motor body
when reattached. Disassemble and wash the
food processor bowl, bowl lid (ensure that the
removable gear box has been removed from
the lid prior to washing), whisk, S Blade™,
variable mashing leg and adjustable slicing
disc in warm soapy water, rinse and dry
thoroughly. Ensure no water remains on
the chopper bowl lid or whisk attachment to
avoid water running into the motor body
when reattached.
NOTE
The detachable blending leg, processing
bowl (without the gearbox), S Blade™, variable
mashing leg and whisk can also be washed in
the dishwasher (top shelf only). The whisk gear
box, processor gear box and motor body are
not dishwasher safe – see the care and cleaning
section of this booklet for cleaning instructions
of these parts.
This immersion blender is a versatile
appliance that can be attached to:
The stainless steel blending leg – for use as
an immersion blender.
The food processor bowl with S Blade™,
adjustable slicing disc, reversible shredding
disc - for use as a mini food processor.
The variable mashing leg – for use in
mashing fruits and vegetables.
The whisk attachment – for use as a
hand whisk.
TO ATTACH THE BLENDING LEG
Hold the blending leg with the blades down,
and align the top end of the blending leg with
the corresponding end of the motor body and
push until the blending leg clicks and locks
onto the motor body.
Always ensure blending leg is dry, and no
water left inside, before reattaching.
USING AS AN IMMERSION BLENDER
Ensure the blending leg is assembled to the
motor body as detailed above.
1. Place food to be processed into a jug (or a
sufficiently large mixing bowl or saucepan).
The jug should be only be ½ full or less
when blending liquids or when making a
puree of fruit and/or vegetables.
2. Insert the plug into a 110/120V power
outlet and turn the power on.
3. By turning the dial at the top of motor body,
select a speed from 1 to 15.
NOTE
If selecting a higher speed, it is recommended
that you start on a slow speed and then
increase to high speed to avoid splattering and
over-processing.
4. Place the blending leg as deeply as possible
into the jug and press the trigger switch
to turn the immersion blender on. The
button must be held for the required
duration of operation.
5. Work through the ingredients in the jug
with a gentle raising and lowering motion.
BSB530XL_IB_C16.indd 9 7/11/2016 1:45 PM
10
6. Turn the motor off by releasing the trigger
switch.
7. Ensure the motor has completely stopped
before lifting the blender out of the jug.
8. When processing has finished remove the
power plug.
TO DETACH THE BLENDING LEG
Ensure the trigger switch is released and the
appliance is unplugged. Hold the motor body
with one hand, and using thumb and finger
of the other hand, press on the two EJECT
buttons on either side of the motor body.
Pull the motor body away from the blending
leg to detach.
RECOMMENDATIONS WHEN USING
AS AN IMMERSION BLENDER
The immersion blender blends foods and
liquids rapidly, therefore it is easy to over
process. Remember when using the blending
leg to stop the immersion blender and check
food throughout the operation.
Allow food to cool before blending.
The stainless steel blending leg allows for hot
food to be processed directly in the saucepan.
This makes blending soups and sauces very
easy.
For safety reasons remove saucepan away
from the heat before processing.
Ensure the body of the appliance and power
cord are kept away from any
heat source.
When puréeing and blending, cut food into
uniform sizes. This will ensure smooth and
consistent results.
Warm all liquids to be added to soups and
purées, this will ensure even blending.
Do not operate the appliance continuously
for more than 1 minute. Allow the motor to
rest for 1 minute between each use.
If food becomes lodged around the processing
blade or in the blade guard, follow the
following safety instructions:
1. Release the trigger switch to power off and
unplug the cord.
2. Use a spatula to carefully dislodge the food.
Do not use fingers as the blades are sharp.
3. After the food has been removed and blades
are clear, plug the appliance back into the
power supply and continue blending.
USING THE FOOD
PROCESSOR BOWL
Attaching gearbox to food processing
bowl lid
1. Place the gearbox into the food processor
lid, it will click into place.
BSB530XL_IB_C16.indd 10 7/11/2016 1:45 PM
11
2. To attach the motor click it into place on
the gearbox.
To attach the food processing bowl, food
processor attachments and lid
1. Remove the food processing bowl from the
storage unit and place onto a counter-top
or table ensuring that the surface is clean
and level.
2. Choose one of the following food processor
attachments:
- S Blade™
- Adjustable slicer
- Reversible shredder
3. There is a common spindle that is used
across all of the three food processor
attachments.
When using the reversible shredder
1. Place the spindle into the center of the food
processing bowl.
CAUTION
Caution should be taken when handling the
shredding disc.
2. Holding the reversible shredding disc,
notice that there is a side for coarse
shredding and a side for fine shredding.
Place the side you require up. Align the hole
in the center of the disc with the spindle and
ensure that it is pushed down firmly.
3. Place the processing bowl lid into position
and ensure that it is on correctly aligned
and locked into place.
When using the adjustable slicer
1. Place the spindle into the center of the food
processing bowl.
CAUTION
Caution should be taken when handling the
adjustable slicing disc.
BSB530XL_IB_C16.indd 11 7/11/2016 1:45 PM
12
2. The adjustable slicing disc has 19 precise
settings. To adjust the settings hold the
adjustable slicing disc by the edge (on the
opposite side of the cutting blade) with one
hand and turn the rotating collar on the
bottom of the disc to the desired setting
with the other hand.
3. Place the adjustable slicing disc onto the
spindle. Ensure that it is pushed down
into place.
4. Place the processing bowl lid into position
and ensure that it is on correctly aligned
and locked into place.
When using the S Blade™
1. Using care, hold the S Blade™ in one hand,
with the other hand, place the spindle
through the center of the S Blade™ from
underneath. The blade should self-locate
at the base of the spindle. The blade will
sit loosely on the spindle but will lock into
place during processing.
CAUTION
Caution should be taken when handling the
S Blade™ as the blades are extremely sharp.
2. Place the S Blade™ and spindle into the
center of the food processing bowl.
3. Align and lock the processing bowl lid
into place.
BSB530XL_IB_C16.indd 12 7/11/2016 1:45 PM
13
Once the blade or disc has been selected for
the food processor and you have assembled as
listed in the previous instructions, you can now
process food.
Place the ingredients inside the processing
bowl or in the feed chute (depending on the
task). Do not exceed the maximum (MAX)
marking. Insert the gear box into the lid of the
food processor.
NOTE
Always place the S Blade™ into the food
processor prior to placing the food into the
food processor. If using the adjustable slicer
or the reversible shredding disc, you are able
to assemble the processor before adding
ingredients to the bowl. Ingredients used with
these discs will need to be added through the
small or large feed chute. Some foods, such as
nuts, can stop the S Blade™ from engaging the
built in safety mechanism. If you have difficulty
closing the lid with ingredients such as these
we advise to load them through the feed chute
after the processor has been fully assembled.
TO USE THE FOOD PROCESSOR
1. Insert the plug into a 110/120V outlet.
2. Select a speed between 1–15 on the speed
control dial.
3. Press the trigger switch to turn the
appliance on and start the processing
action.
4. Feed the food through the feed chute of the
food processor, using the food pusher to
push it down.
BSB530XL_IB_C16.indd 13 7/11/2016 1:45 PM
14
5. When processing has finished turn the
motor off by releasing the trigger switch
and remove the power plug.
6. Detach the motor from the gear box and
remove the lid from the bowl (refer to
instructions). Carefully remove the food
processing disc or S Blade™ and use a
spatula to remove any excess food from the
discs or blades and to remove processed
food from the bowl.
NOTE
When processing food through the feed
chute(s) you must keep pressing the trigger
switch in order to keep the motor on.
TO DETACH THE FOOD PROCESSING
BOWL AND LID
Ensure the trigger switch is released and the
appliance is unplugged.
Hold the motor body with one hand and using
thumb and finger of the other hand, press on
the two EJECT buttons on either side of the
motor body. Pull the motor body away from the
processing bowl gearbox to detach.
TO DETACH THE GEARBOX
FROM THE LID
Lift the gear box up from the processing
bowl lid.
RECOMMENDATIONS WHEN USING
THE IMMERSION BLENDER WITH
THE PROCESSING BOWL
Do not operate the immersion blender when
the processing bowl is empty.
The bottom of the processing bowl features
a anti-slip rubber rim around the bottom of
the bowl. This keeps the processing bowl
stable, however it is recommended during
processing to hold the motor body with one
hand and the processing bowl and lid with
the other.
When processing, cut food into uniform sizes
to ensure quicker, even and more consistent
results.
The immersion blender blends foods and
liquids rapidly, therefore it is easy to over
process. Remember to check food throughout
the operation.
CAUTION
DO NOT process hard foods such as ice,
coffee, cereal or chocolate in lumps in the
processing bowl, as damage to the blades
may result.
DO NOT process boiling or hot foods in the
processing bowl.
NEVER remove the blades from the bowl
before processing is completed.
BSB530XL_IB_C16.indd 14 7/11/2016 1:45 PM
15
BEFORE FIRST USE
Remove any packaging material and
promotional labels. Wash blade and two
parts of the mashing leg before use.
CAUTION
Never immerse the motor body or gearbox
in water or any other liquid.
ASSEMBLY OF THE MASHING LEG
1. Hold the outer leg and insert the gearbox
making sure ALIGN arrows are aligned.
2. Hold both outer leg and gearbox firmly with
one hand and insert inner leg until it clicks
into place.
3. Holding gearbox twist outer leg to lock.
4. Align the mashing leg with the motor
body and push the two parts together until
it clicks.
5. Place blade on underside of the mashing
head. To lock the blade rotate in a counter-
clockwise direction. Blade will not attach if
the leg is not attached to the motor body.
BSB530XL_IB_C16.indd 15 7/11/2016 1:45 PM
16
TO USE THE VARIABLE
MASHING LEG
For food preparation tips and recipes refer
to the recipes section. Ensure the variable
mashing leg is completely and properly
assembled.
1. Place food to be mashed into a blending jug
or a sufficiently large mixing bowl
or container.
2. Insert the plug into a 110/120V power
outlet.
3. Select the desired setting on the variable
mashing leg.
4. Select a high speed on the speed control
dial of the motor.
5. Place the variable mashing leg into
ingredients and press the trigger switch to
turn the mashing leg on.
6. Move the mashing leg through the
ingredients with a gentle raising and
lowering action until desired texture is
achieved.
7. Turn the motor off by releasing the trigger
switch before lifting the mashing leg out of
the bowl and remove the power plug.
TO DETACH THE VARIABLE
MASHING LEG
Ensure the trigger switch is released and the
appliance is unplugged.
Hold the motor body with one hand, and, using
thumb and finger of the other hand, press on
the two EJECT buttons on either side of the
motor body. Pull the motor body away from the
mashing leg to detach.
RECOMMENDATIONS WHEN USING
WITH THE VARIABLE MASHING LEG
Release the trigger switch and ensure the
mashing leg has completely stopped turning
before removing the mashing leg from the
food during operation.
Place the mixing bowl on a damp cloth
during mashing. This will keep the mixing
bowl stable.
USING AS A WHISK
Remove blending leg from motor body (follow
the instructions “To detach the blending leg”).
Align the top end of the whisk gearbox with
the corresponding end of the motor body and
push until the gearbox clicks into place. Align
the shaft of the whisk with the hole in the
gearbox and push until the whisk clicks and
locks into place.
BSB530XL_IB_C16.indd 16 7/11/2016 1:45 PM
17
TO USE THE WHISK
For food preparation tips and recipes refer
to the recipes section. Ensure the whisk is
completely and properly assembled.
1. Place food to be processed into a blending
jug or a sufficiently large mixing bowl or
container.
2. Insert the plug into a 110/120V power
outlet.
3. Select a speed between 1–15 on the speed
control dial.
4. Place the whisk into ingredients and press
the trigger switch to start whisking.
5. Move the whisk through the ingredients
with a gentle raising and lowering action
until desired texture is achieved.
6. Turn the motor off by releasing the trigger
switch before lifting the whisk out of the
bowl remove the power plug.
TO DETACH THE WHISK
Ensure the trigger switch is released and the
appliance is unplugged. Hold the motor body
with one hand, and, using thumb and finger
of the other hand, press on the two EJECT
buttons on either side of the motor body. Pull
the motor body away from the whisk to detach.
RECOMMENDATIONS WHEN USING
THE WHISK ATTACHMENT
Do not allow the whisk to touch the bottom or
sides of mixing bowl while the appliance is in
operation, as this may damage the whisk.
To incorporate air into the ingredients when
whisking, use a deep and wide enough
container for the amount of ingredients and
move the whisk with a gentle raising and
lowering action.
Release the trigger switch and ensure the
whisk has completely stopped turning before
removing the whisk from the food during
operation.
Place the mixing bowl on a damp cloth
during whisking. This will keep the mixing
bowl stable.
Always use fresh chilled cream and
fresh eggs at room temperature to achieve
greater and more stable volume when
whisking.
Always ensure the whisk and mixing bowl
are completely clean and free of fat before
whisking egg whites.
It is recommended to use the highest speed
when whisking egg whites and cream.
BSB530XL_IB_C16.indd 17 7/11/2016 1:45 PM
18
Care & Cleaning
MOTOR BODY
To remove any food residue wipe the motor
body and cord with a damp cloth only.
Do not use abrasive cleaners or steel wool.
Never immerse the motor body in water or any
other liquid. Do not place motor body
in dishwasher.
BLENDING LEG
Before cleaning remove the plug from the
power outlet. Remove the motor body from
the stainless steel blending leg. The stainless
steel blending leg can be hand washed in hot
soapy water, rinsed and dried thoroughly after
each use. Alternatively, the blending leg can
also be washed in the dishwasher. (TOP SHELF
ONLY) Do not use abrasive cleaners or steel
wool.
QUICK WASH: Between each processing
task, with the motor body attached place the
stainless steel blending leg and blade assembly
only in to a jug of water and press the trigger
switch to turn on for 5 seconds.
This will remove any food on the blade and
leg and allow you to continue onto the next
processing task.
FOOD PROCESSING BOWL, FOOD
PROCESSING BOWL LID, S BLADE™,
ADJUSTABLE SLICING DISC &
REVERSIBLE SHREDDER
Before cleaning remove the plug from the
power outlet. Remove the motor body from the
food processing bowl lid and gear box. Remove
the food processing bowl lid and S Blade™ or
processing disc from the food processing bowl.
NOTE
The processing bowl lid is dishwasher safe.
Simply remove the removable gear box from
the lid prior to placing in the dishwasher.
The food processing bowl, bowl lid,
S Blade™ and processing discs should be
hand washed in hot soapy water, rinsed and
dried thoroughly after each use. Alternatively,
the food processing bowl, bowl lid, S Blade™,
adjustable slicing disc and reversible shredder
can also be washed in the dishwasher (TOP
SHELF ONLY). The S Blade™ comes with a
cover for your safety. This cover can be used
on the blade in the dishwasher. Do not use
abrasive cleaners or steel wool.
CARE & CLEANING OF THE GEARBOX
The gearbox should always be removed from
the lid prior to any cleaning.
The gearbox simply lifts out of the lid by
pulling it up.
NOTE
The gear box is not dishwasher safe and should
never be immersed in liquid at all.
To clean the gearbox, remove from the lid and
wipe down with a damp cloth only. Do not use
abrasive cleansers or steel wool.
VARIABLE MASHING LEG
Before cleaning remove the plug from the
power outlet. Remove the motor body and
mashing leg gearbox from the mashing leg.
The mashing leg can be hand washed in hot
soapy water, rinsed and dried thoroughly after
each use.
BSB530XL_IB_C16.indd 18 7/11/2016 1:45 PM
19
TO DISASSEMBLE THE
VARIABLE MASHING LEG
1. Ensure the motor is unplugged and
attached to the mashing leg. Remove the
mashing blade that is found under the base
of the leg by turning it clockwise.
2. Disassemble the gear box from motor body,
then turn the mashing leg to align and
remove the inner and outer legs from the
gear box together.
3. Lift the outer leg up to separate from the
inner leg.
Both of the legs can now be washed in hot
soapy water, then rinsed and dried thoroughly.
Alternatively, the mashing leg can be washed
in the dishwasher (TOP SHELF ONLY).
CAUTION
Do not use abrasive cleaners or steel wool.
NOTE
Mashing leg gear box is not dishwasher safe.
WHISK
Before cleaning remove the plug from the
power outlet. Remove the motor body from
the whisk and the gearbox from the whisk. The
whisk can be hand washed in hot soapy water,
rinsed and dried thoroughly after each use.
Alternatively, the whisk can also be washed in
the dishwasher. (TOP SHELF ONLY)
Do not use abrasive cleaners or steel wool.
Whisk gear box is not dishwasher safe.
STORAGE
Before storage remove the plug from the
power outlet. Ensure the appliance is clean and
completely dry.
Insert assembled S Blade™ and spindle into
the processing bowl, then place the reversible
shredder on the spindle. Align and lock the
processing bowl lid to the processing bowl
and place processing bowl onto the storage
unit with all of the accessories on the built in
accessory holders.
NOTE
The adjustable slicing disc is stored under
the food processing bowl, make sure that
the adjustable blade is set to STORAGE
POSITION.
BSB530XL_IB_C16.indd 19 7/11/2016 1:45 PM
20
Troubleshooting
PROBLEM SOLUTION
Blades don’t turn when
processing.
May be too much food in bowl; reduce quantity.
Pieces of food, such as meat are too large, reduce size.
Unable to lock lid into place.
Spindle may be out of position. Remove lid, straighten spindle as
vertical as possible and reposition lid.
Food may stuck underneath the S Blade™ preventing the lid from being
locked into place. Food such as nuts can be loaded through the feed
chute.
Gear box in lid jumps out of
lid when processing.
Replace gear box and ensure that the control grip is held vertically and
firmly.
Mashing leg won’t attach onto
mashing leg gear box.
Ensure mashing leg and gear box arrow graphics are vertically aligned.
Twist mashing leg counter-clockwise to lock for use.
Blades won’t remove from
mashing leg.
Mashing leg should still be assembled to the gear box assembly and to
the unplugged motor body. Rotate blades clockwise.
Shredding disc slows down
when in use.
Shredding has exceeded Max level. Empty bowl and continue to shred.
Too much force is being used when shredding. Reduce force when
pushing.
Processing bowl does not sit
flat on storage base.
Ensure adjustable slicing disc is set to ‘Storage Position’.
Motor sounds like it is not able
to process load.
Speed may not be correct. Refer to processing guide for correct speeds.
BSB530XL_IB_C16.indd 20 7/11/2016 1:45 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Breville the All in One Manuel utilisateur

Catégorie
Robots culinaires
Taper
Manuel utilisateur

dans d''autres langues