GE IM-4A Mode d'emploi

Icemaker Accessory Kit
GEAppliances.com
IM-4A
162D4614P011     49-60191-1     11-02 JR   
Safety Information  . . . . . . . . . 2
Operating Instructions  . . . . . .3
Before You Call For Service . .4–6
Normal Sounds You May Hear . .3
Preparing for Vacation  . . . . . . .3
When You Should Set the 
Icemaker Power Switch 
to O (Off)  . . . . . . . . . . . . . . . . .3
Installation Instructions
Cold Water Line . . . . . . . . .34–37
Fill Tube Templates  . . . . . . . . .38
Fill Tube Extension 
Templates  . . . . . . . . . . . . . . . .38
Icemaker   . . . . . . . . . . .10–13
Icemaker   . . . . . . . . . . .14–17
Icemaker   . . . . . . . . . . .18–21
Icemaker   . . . . . . . . . . .22–25
Icemaker   . . . . . . . . . . .26–29
Icemaker   . . . . . . . . . . .30–33
Parts List  . . . . . . . . . . . . . . . .8, 9
Consumer Support
Consumer Support . . Back Cover
Warranty  . . . . . . . . . . . . . . . . . 39
R
Q
P
N
M
L
Which instructions should
you follow?
Look for a label on the back of the
refrigerator that will tell you which
instructions to use:
or 
RQPNML
Machine à glaçons
Trousse
Máquina de Hielos
Equipo de Accesorios
Manuel d’utilisation 
et d’installation
Owner’s Manual and
Installation Instructions
Manual del propietario 
e instalación
La section française commence à la page 40
La sección en español empieza en la página 84

2

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

READ AND SAVE THESE INSTRUCTIONS

SAFETY PRECAUTIONS

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

FOR YOUR SAFETY:

Do not place fingers or hands in the automatic

icemaking mechanism while the refrigerator is

plugged in. This will help protect you from

possible injury.

It will also prevent interference with moving

parts of the ejector mechanism and the heating

element that releases the cubes, located on the

bottom of the icemaker.

3

■ The icemaker water valve will buzz when

the icemaker fills with water. If the power

switch is in the I (on) position, it will buzz

even if it has not yet been hooked up to

water. Keeping the power switch in the

I (on) position before it is hooked up to

water can damage the icemaker. To

prevent this, move the power switch to

the O (off) position. This will stop

the buzzing.

■ The sound of cubes dropping into the bin

and water running in the pipes as the

icemaker refills.

About the automatic icemaker. GEAppliances.com

A newly-installed refrigerator may take 12 to 24 hours to begin making ice.

Icemaker

Feeler Arm

Power

Switch

Automatic Icemaker

The icemaker will produce seven cubes

per cycle---approximately 100–130 cubes

in a 24-hour period, depending on

freezer compartment temperature, room

temperature, number of door openings

and other use conditions.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch to O (off).

When the refrigerator has been connected

to the water supply, set the power switch to

I (on). The green light will come on.

The icemaker will fill with water when

it cools to freezing. A newly-installed

refrigerator may take 12 to 24 hours

to begin making ice cubes.

You will hear a buzzing sound each time

the icemaker fills with water.

Throw away the first few batches of ice to

allow the water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler

arm, the icemaker will stop producing ice.

It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes

will become cloudy, taste stale and shrink.

If ice cubes get stuck in the icemaker, the

green power light will blink. To correct

this, set the power switch to O (off) and

remove the cubes. Set the power switch to

I (on) to restart the icemaker.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

Green Power Light

Preparing for Vacation

Set the icemaker power switch to O (off)

and shut off the water supply to the

refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water

supply system (on some models) to prevent

serious property damage due to flooding.

When you should set the icemaker power switch to O (off)

■ When the ice storage bin is removed for

more than a minute or two.

■ When the water supply will be shut off for

several hours.

■ When the refrigerator will not be used for

several days.

Normal sounds you may hear

4

Problem Possible Causes What To Do

Automatic icemaker Freezer compartment • After installing the kit, allow the refrigerator to completely

does not work/’not too warm. cool down for 24 hours. Once the compartment is cool, the

icemaker will begin ice production.

Icemaker is not turned on. • Move the icemaker

power switch to the

I (on) position.

The indicator light

below the switch

will turn green.

Icemaker is not plugged • If using a power cord adapter, make sure that it is fully

in correctly. connected. Also check that the icemaker cord plug is fully

inserted into the socket. See Plug in the icemaker. When the

icemaker is turned on, the green power indicator light

below the switch will turn on.

Water line kinked. • Check that the plastic water

line running from the valve

to the water tube inlet is not

kinked. See Connect the

water line. A kink in the

water line will restrict flow

to the water line.

Water supply turned off or • After installing the kit, make sure the house water supply

not connected. to the refrigerator has been turned on.

Piled up cubes in the storage bin • Level cubes by hand.

cause the icemaker to shut off.

Water valve is not plugged in • Check that the valve wire

correctly. adapter is completely

plugged onto the male

connector plug and the

terminals on the water valve.

See Attach the water valve.

Before you call for service…

Troubleshooting Tips

Save time and money! Review the following chart first

and you may not need to call for service.

Power

Switch

Green

Indicator

Light

Feeler Arm

Icemaker

Clip

Restraints

onto

Locking

Tabs

Locking

Tabs

Hook

Adhesive-backed

Fasteners for

Water Tube

Male

Connector

Plug

Valve

Terminals

Problem Possible Causes What To Do

Leaking water around Foam in the fill cup from • If the fill tube was installed by sliding it through the back

the fill cup installing the fill tube. of the refrigerator, it may have picked up pieces of foam as

it was pushed through. This foam can interfere with the

water flow in the fill cup. Check the cup and make sure

there are no foam pieces.

Fill tube not correctly seated • Check that the fill tube is

in the fill cup. correctly inserted in the

fill cup opening.

See Mount the icemaker.

Leaking water behind House supply not properly • Check that the house supply is firmly attached to the

the refrigerator connected to the water valve. water valve. See Water line installation instructions.

Water line not connected to the • Check that the plastic

water tube inlet. water line running from

the valve to the water tube

inlet is firmly attached with

the hose clamp. See Connect

the water line.

Slow ice/freezer not Door left open. • Check to see if package is holding door open.

cold enough

Temperature control not •See About the Temperature Control.

set cold enough.

Ice cubes too small/ Water shutoff valve connecting •We recommend drilling a 1/4″ hole

slow ice refrigerator to house water line in the water pipe to connect the water

may be clogged. shut-off valve. Failure to drill a 1/4″

hole may result in reduced ice

production or smaller cubes.

See Installing the water line.

Water line kinked. •Check that the plastic water

line running from the valve

to the water tube inlet is not

kinked. See Connect the

water line. A kink in the

water line will restrict flow

to the icemaker.

5

Fill Tube

Fill

Tube

Fill

Cup

Water Tube

Inlet

Hose Clamp

Water Line

Adhesive-backed

Fasteners for

Water Tube

Drill 1/4″ hole

in water pipe

Problem Possible Causes What To Do

Ice cubes have Ice storage bin needs cleaning. •Empty and wash bin. Discard old cubes.

odor/taste

Food transmitting odor/taste •Wrap foods well.

to ice cubes.

Interior of refrigerator •See Care and cleaning.

needs cleaning.

Frequent “buzzing” Normal operation. •During normal operation, the water valve will “buzz”

sound when the icemaker fills with water.

Before you call for service…

Troubleshooting Tips

Save time and money! Review the following chart first

and you may not need to call for service.

6

7

BEFORE YOU BEGIN

Installation IM-4A

Instructions Icemaker Kit

Read these instructions completely and carefully.

•

IMPORTANT – Save these

instructions for local inspector’s use.

•

IMPORTANT – Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions

for future reference.

• Skill level – Installation of this appliance requires

basic mechanical and electrical skills.

• Completion time – 20–60 minutes

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is

not covered under the Warranty.

It’s important that you use the water valve and fill tube

extension that come with this kit, even though your

refrigerator may already have them installed.

The old valve will not allow enough water through

to fill the icemaker properly and will cause damage.

The fill tube extension needs to be a different length

than the original tube for proper water flow. Cut the

tube to the length indicated for your model of

refrigerator.

ARE YOU REPLACING AN

ICEMAKER WITH THIS KIT?

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com

In Canada, call 1.800.361.3400

or Visit our Website at: geappliances.ca

There is a label on the back of the refrigerator

that will tell you whether to use Instructions:

or

Pages 8–31 contain six different Installation Instructions.

The actual installation of the icemaker will depend on

which model refrigerator you have.

RQPNML

WHICH INSTRUCTIONS SHOULD

YOU FOLLOW?

• If the unit is damaged in shipment, return the unit

to the store in which it was bought for repair or

replacement.

• If the unit is damaged by the customer, repair or

replacement is the responsibility of the customer.

• If the unit is damaged by the installer (if other than

the customer), repair or replacement must be made

by arrangement between customer and installer.

DAMAGE – SHIPMENT/INSTALLATION

8

Installation Instructions

CONTENTS OF KIT IM-4

Owner’s Manual &

Installation Instructions

2

Ice Bucket

9

Water Line Clamp

(strain relief), for

house water line

6

Hex-Head Screw

for Water Line Clamp

5

Water Valve and

Tube Assembly

3

Hex-Head Screw, for

attaching water valve

10

Adhesive-Backed Water Tube

Fasteners, to secure plastic

water tube (4)

4

12

Water Tube Inlet

11

Phillips Head Screws,

for mounting icemaker (2)

Warranty Label

7

ICEMAKER

WARRANTY VERIFICATION

Date Installed

Dealer

Fill Tube Extension

(3/4″ O.D.)

8

15

Fill Tube

(5/8″ O.D.)

13

Fill Tube with Foil

(5/8″ O.D.)

14

Icemaker Fill Cup

(side-mounted)

Icemaker

1

Installation

Instructions

16

Hose Clamp

Water Tube

Inlet Cover

17

Hex-Head Screws, for

attaching water tube

inlet cover

18

9

Installation Instructions

Parts List Use with Installation Instructions:

LMNPQR

1 Icemaker XXXXXX

2 Owner’s Manual and Installation Instructions XXXXXX

3 Water Valve and Tube Assembly XXXXXX

4 Adhesive-Backed Water Tube Fasteners XXXXXX

5 Hex-Head Screw for Water Line Clamp XXXXX

6 Water Line Clamp (strain relief) XXXXXX

7 Warranty Label XXXXXX

8 Fill Tube Extension (3/4″ O.D.) XX

9 Ice Bucket XXXXX

10 Hex-Head Screw XXXXXX

11 Phillips Head Screw (2) XX X

12 Water Tube Inlet XXXXX

13 Fill Tube (5/8″ O.D.) X XXX

14 Fill Tube with Foil (5/8″ O.D.) X

15 Icemaker Fill Cup (side-mounted) XXXXXX

16 Hose Clamp XXXXXX

17 Water Tube Inlet Cover X

18 Hex Head Screw (2) for Water Tube Inlet Cover X

10

2

Installation Instructions

ICEMAKER INSTALLATION INSTRUCTIONS L

Are these the right instructions for your model? Follow the Installation Instructions indicated by

the label on the back of the refrigerator --- or

RQPNML

BEFORE YOU BEGIN

Read each step thoroughly before proceeding.

•

CAUTION – Unplug the

Refrigerator. To eliminate the danger

of electric shock during installation,

you must unplug the refrigerator

from its electrical outlet.

Flat blade and Phillips

screwdrivers

Pliers

TOOLS YOU WILL NEED

Sharp knife

1

REMOVE ICE CUBE TRAY SHELF

• Remove the two screws securing the ice cube tray

to the side wall of the freezer. Remove the tray.

• Replace the screws but do not screw them all the

way in. The screw heads should extend about

1/2″ (13 mm) from the side wall of the freezer.

1/4″ Nutdriver or adjustable wrench

Remove

plug

INSTALL FILL TUBE EXTENSION

• Cut the fill tube extension (8)

to the length (refer to the

template on page 38) with

a sharp knife or a single-edge

razor blade and slide it onto

the fill tube against the stop.

L

3

PREPARE FOR INSTALLATION

• Remove and discard the large white plug from

the rear freezer wall.

• Remove the outlet cover with a flat-blade

screwdriver.

L

8

INSTALL THE ICE BUCKET

Put the ice bucket (9) in

place under the icemaker.

Make sure the icemaker

power switch is set to

O (off).

Installation Instructions

INSTALL THE ICEMAKER FILL CUP

Install the icemaker fill cup (side-mounted) (15)

into the icemaker as shown.

5

PLUG IN THE ICEMAKER

Holding the icemaker in place, insert the icemaker

power cord plug into the socket, making sure that

the prongs and holes are matched. Press the plug

firmly into the socket. Lock the plug in place by

clipping the restraints onto each side of the plug.

Make sure the restraints click into place. Make sure

the power cord is still in the hook on the back of

the icemaker.

6

ATTACH WARRANTY LABEL

A label (7) is provided with this kit to record the

date of installation for warranty purposes. Apply it

to the back of the refrigerator.

9

KEEP THIS MANUAL

The warranty for the icemaker is printed in this

manual. Keep this manual with your Refrigerator

Owner’s Manual.

The icemaker installation inside the freezer is now

complete. Continue to the Water Valve Assembly

section.

10

15

MOUNT THE ICEMAKER

• Lift the icemaker so the fill tube extension (8)

fits in the fill cup opening (C). Hang the

icemaker on the two mounting screws (A).

Make sure:

• The power cord is still firmly in the socket.

• The fill tube extension (8) is still in the fill cup

opening. (Check the rear of the refrigerator to

make sure the fill tube has not been pushed out

of the back of the refrigerator.)

• The icemaker mounting screws are located in

the uppermost position of the mounting slots.

• The icemaker is level.

THEN TIGHTEN THE ICEMAKER

MOUNTING SCREWS SECURELY.

7

8

C

A

8

11

SET POWER SWITCH TO O (off)

Set the icemaker power switch to O (off). Leave

the power switch in the O (off) position until the

refrigerator is connected to the water supply to

prevent premature operation.

4

Power

Switch

9

Hook

12

Installation Instructions

REMOVE THE COVER

At the bottom rear of the refrigerator, remove the

screw(s) holding the access cover.

Bend the cover back for access to the compartment.

Be sure to save the screws as the access cover must

be reinstalled later to ensure your refrigerator will

function properly.

1

BEFORE YOU BEGIN

Read each step thoroughly before proceeding.

•

CAUTION – Unplug the

Refrigerator. To eliminate the danger

of electric shock during installation,

you must unplug the refrigerator from

its electrical outlet.

WATER VALVE ASSEMBLY INSTALLATION INSTRUCTIONS L

Are these the right instructions for your model? Follow the Installation Instructions indicated by

the label on the back of the refrigerator --- or

RQPNML

Flat blade and Phillips

screwdrivers

Pliers

TOOLS YOU WILL NEED

Sharp knife

1/4″ and 5/16″ Nutdrivers

• Fasten the water valve to the

cabinet by driving

the

hex-head screw (10) from the kit into the

hole in the cabinet leg.

ATTACH THE WATER VALVE

• Locate the female connector plug (C), which is

attached to the cabinet by a metal or plastic clip.

Remove the clip by removing the screw.

2

• Plug the female connector (C) onto the male

terminals on the water valve (3). Either wire

can go on either terminal.

Metal or plastic clip

C

3

10

Installation Instructions

ROUTE AND ATTACH

THE WATER TUBE

• Fasten the plastic water tube to the back of the

refrigerator with the remaining adhesive-backed

fasteners (4), spacing the fasteners as shown to

take up slack in the tube.

5

WATER VALVE INSTALLED

Refer to the Water Line Installation Instructions for

connection to the home water supply. After water

line installation is completed, set the icemaker

power switch to I (on).

The icemaking cycle will not begin until the icemaker

and freezer compartment reach operating temperature,

then icemaking will begin automatically.

6

Adhesive-backed

fasteners for

water tube

13

INSTALL WATER LINE CLAMP

• Attach the metal water line clamp (strain relief)

(6) to the refrigerator. Drive one of the screws,

removed in Step 1, into the cabinet edge through

the clamp and hole in compressor cover.

• The metal clamp is for the house water line (see

Water Line Installation Instructions). It is not to

be used for the water tube from the water valve

up to the inlet.

4

6

Screw

CONNECT WATER TUBE

TO EXISTING INLET

• Squeeze the ends of the hose clamp (16) from the

kit with pliers and slide the clamp over the inlet,

located in the top right corner of the refrigerator.

• While still squeezing the clamp, insert the free end

of the water tube (3) into the inlet as far as it will go.

• Then slide the clamp downward to capture the

water tube in place.

• Using one of the adhesive-backed fasteners (4),

secure the water tube to the back of the refrigerator

about 1/2″ below the inlet.

3

16

4

Inlet

3

14

CUT FILL TUBE

• If the refrigerator already has a water tube and

inlet assembly on the back of the refrigerator,

go to Step 5.

• Cut the fill tube (13) to the length (refer to

the templates on page 38) with a sharp knife

or a single-edge razor blade.

M

3

Installation Instructions

ICEMAKER INSTALLATION INSTRUCTIONS M

Are these the right instructions for your model? Follow the Installation Instructions indicated by

the label on the back of the refrigerator --- or

RQPNML

BEFORE YOU BEGIN

Read each step thoroughly before proceeding.

•

CAUTION – Unplug the

Refrigerator. To eliminate the danger

of electric shock during installation,

you must unplug the refrigerator from

its electrical outlet.

Flat blade and Phillips

screwdrivers

Pliers

TOOLS YOU WILL NEED

Sharp knife

REMOVE THE WHITE PLUG

AND OUTLET COVER

• Remove the outlet cover with a flat-blade

screwdriver located either on the left or back

freezer wall near the top.

• Remove and discard the white plug from the

upper left hand corner of the freezer wall.

2

REPOSITION FREEZER SHELF

For models with two temperature controls

(refrigerator and freezer) only:

• Make sure the freezer shelf is in the lowest

position.

1

Remove

plug

13

INSTALL FILL TUBE

• Slide the fill tube (13) onto

the water tube inlet (12).

• Go to the back of the

refrigerator. Find the small

label or plug button

(depending on model) and

remove it. On the tube side of

the water tube inlet (12), there

is an adhesive backing. Remove

the adhesive backing and slide

the tube into the hole near the top at the back of

the refrigerator. Firmly press on the inlet to secure

it to the refrigerator.

4

12

13

PREPARE FOR INSTALLATION

Inside the freezer, loosen the two mounting screws

(B) but do not screw them all the way out. If your

model does not have the screws already in the

freezer wall, look for two plug buttons. Remove the

plug buttons and insert the two Phillips head screws

(11). The screws should extend approximately

1/2″ (13 mm) out from the freezer wall.

5

B

15

Installation Instructions

10

8

INSTALL THE ICE BUCKET

Place the ice bucket (9) under the icemaker.

Make sure the icemaker power switch is in the

O (off) position.

11

9

ATTACH WARRANTY LABEL

A label (7) is provided with this kit to record the

date of installation for warranty purposes. Apply it

to the back of the refrigerator.

12

KEEP THIS MANUAL

The warranty for the icemaker is printed in this

manual. Keep this manual with your Refrigerator

Owner’s Manual.

The icemaker installation inside the freezer is now

complete. Continue to the Water Valve Assembly

section.

13

D

MOUNT THE ICEMAKER

• Lift the icemaker so the fill tube (13) or fill tube

extension (8) (depending on model) fits in the

fill cup opening (D). Hang the icemaker on the

two mounting screws (B).

Make sure:

• The power cord is still firmly in the socket.

• The fill tube (13) or fill tube extension (8)

extends into the fill cup opening at the back of

the icemaker. (Check the rear of the refrigerator

to make sure the fill tube has not been pushed

out of the back of the refrigerator).

• The icemaker mounting screws are located in

the uppermost position of the mounting slots.

• The icemaker is level.

THEN SECURELY TIGHTEN THE ICEMAKER

MOUNTING SCREWS.

B

INSTALL FILL TUBE EXTENSION

For models with one temperature control

(refrigerator) only:

• Cut the fill tube extension (8) to the length

(refer to the template on page 38) with a

sharp knife or a single-edge razor blade and slide

it onto the fill tube against the stop.

M

6

M

8

SET POWER SWITCH TO O (off)

Set the icemaker power switch to O (off). Leave

the power switch in the O (off) position until the

refrigerator is connected to the water supply to

prevent premature operation.

7

Power

Switch

INSTALL THE ICEMAKER FILL CUP

Install the icemaker fill cup (side-mounted) (15)

into the icemaker as shown.

8

15

PLUG IN THE ICEMAKER

Holding the icemaker in place, insert the icemaker

power cord plug into the socket on the side or rear

wall (depending on

model), making sure the

prongs and holes are

matched. Press the plug

firmly into the socket.

Lock the plug in place by

clipping the restraints

onto each side of the

plug. Make sure the

restraints click into place.

Make sure the power cord

is still in the hook on the back of the icemaker.

9

Hook

13

or

16

Installation Instructions

BEFORE YOU BEGIN

Read each step thoroughly before proceeding.

•

CAUTION – Unplug the

Refrigerator. To eliminate the danger

of electric shock during installation,

you must unplug the refrigerator from

its electrical outlet.

WATER VALVE ASSEMBLY INSTALLATION INSTRUCTIONS M

Are these the right instructions for your model? Follow the Installation Instructions indicated by

the label on the back of the refrigerator --- or

RQPNML

Flat blade and Phillips

screwdrivers

Pliers

TOOLS YOU WILL NEED

Sharp knife

1/4″ and 5/16″ Nutdrivers

ATTACH THE WATER VALVE

• Locate the female connector plug. Plug the

female connector (C) onto the male terminals

on the water valve (3). Either wire can go on

either terminal.

2

10

For models with one temperature control

(refrigerator) only:

• Fasten the water valve to the cabinet by driving

the hex-head screw (10) from the kit into the

hole in the cabinet leg.

C

3

REMOVE THE COVER

Remove the compressor compartment access cover.

This requires removing screws which attach the

cover to the back of the refrigerator case.

Be sure to save the screws as the access cover must

be reinstalled later to ensure your refrigerator will

function properly.

1

For models with two temperature controls

(refrigerator and freezer) only:

• Fasten the water valve to the bracket inside the

compressor compartment using the two screws

already in the bracket.

Installation Instructions

ROUTE AND ATTACH

THE WATER TUBE

• Fasten the plastic water tube to the back of the

refrigerator with adhesive-backed fasteners (4),

spacing the fasteners as shown to take up slack

in the tube.

5

WATER VALVE INSTALLED

Refer to the Water Line Installation Instructions for

connection to the home water supply. After water

line installation is completed, set the icemaker

power switch to I (on).

The icemaking cycle will not begin until the icemaker

and freezer compartment reach operating temperature,

then icemaking will begin automatically.

6

Adhesive-backed fasteners

for water tube

17

INSTALL WATER LINE CLAMP

• Attach the metal water line clamp (strain relief)

(6) to the refrigerator. Drive the screw (5) from

the kit through the clamp (6) at the indent into

the back of the cabinet.

• The metal clamp is for the house water line (see

the Water Line Installation Instructions). It is not

to be used for the water tube from the water valve

up to the inlet.

4

5

6

CONNECT WATER TUBE

TO INLET

• Squeeze the ends of the hose clamp (16) from the

kit with pliers and slide the clamp over the inlet,

located in the top right corner of the refrigerator.

• While still squeezing the clamp, insert the free end

of the water tube (3) into the inlet as far as it will go.

• Then slide the clamp downward to capture the

water tube in place.

• Using one of the adhesive-backed fasteners (4),

secure the water tube to the back of the refrigerator

about 1/2″ below the inlet.

3

16

4

Inlet

3

For models with one

temperature control

(refrigerator) only.

For models with two

temperature control

(refrigerator and

freezer) only.

REMOVE ICE CUBE TRAY SHELF

• Remove the two screws securing the ice cube tray

to the side wall of the freezer. Remove the tray.

• There are two white plug buttons above the screw

holes. Remove these plug buttons and install

them in the two screw holes that were used to

hold the ice cube tray shelf.

• Install two Phillips head screws (11) in the holes

that the plug buttons were in, but do not screw

them all the way in. The screw heads should

extend about 1/2″ (13 mm) from the side wall

of the freezer.

18

Installation Instructions

ICEMAKER INSTALLATION INSTRUCTIONS N

Are these the right instructions for your model? Follow the Installation Instructions indicated by

the label on the back of the refrigerator --- or

RQPNML

BEFORE YOU BEGIN

Read each step thoroughly before proceeding.

•

CAUTION – Unplug the

Refrigerator. To eliminate the danger

of electric shock during installation,

you must unplug the refrigerator from

its electrical outlet.

Flat blade and Phillips

screwdrivers

Pliers

TOOLS YOU WILL NEED

Sharp knife

2

PREPARE FOR INSTALLATION

• Remove and discard the large white plug from

the rear freezer wall. Pull out the gray insulation

plug and remove any debris.

• Remove the outlet cover with a flat-blade

screwdriver.

1

Plug

Buttons

11

INSTALL FILL TUBE

• Slide the fill tube with foil (14)

onto the water tube inlet (12),

making sure that the open side

of the fill tube faces up.

• Go to the back of the

refrigerator. On the tube side

of the water tube inlet (12),

there is an adhesive backing.

Remove the adhesive backing

and slide the tube into the hole

near the top at the back of the

refrigerator. Firmly press on the

inlet to secure it to the refrigerator.

• Install the water tube

inlet cover (17) over

the water tube inlet.

Secure the cover

using two hex-head

screws (18).

3

12

14

19

Installation Instructions

SET POWER SWITCH TO O (off)

Set the icemaker power switch to O (off). Leave

the power switch in the O (off) position until the

refrigerator is connected to the water supply to

prevent premature operation.

4

Power

Switch

INSTALL THE ICEMAKER FILL CUP

Install the icemaker fill cup (side-mounted) (15)

into the icemaker as shown.

5

15

PLUG IN THE ICEMAKER

Holding the icemaker in place, insert the icemaker

power cord plug into the socket on the rear wall,

making sure the prongs and holes are matched.

Press the plug firmly into the socket. Lock the plug

in place by clipping the restraints onto each side of

the plug. Make sure the restraints click into place.

Make sure the power cord is still in the hook on the

back of the icemaker.

6

MOUNT THE ICEMAKER

• Lift the icemaker so the fill tube (14) goes into the

fill cup opening (15). Hang the icemaker on the

two mounting screws (11).

Make sure:

• The power cord is still firmly in the socket.

• The fill tube (14) extends into the fill cup

opening at the back of the icemaker. (Check

the rear of the refrigerator to make sure the fill

tube has not been pushed out of the back of

the refrigerator).

• The icemaker mounting screws are located in

the uppermost position of the mounting slots.

• The icemaker is level.

THEN SECURELY TIGHTEN THE ICEMAKER

MOUNTING SCREWS.

7

14

15

INSTALL THE ICE BUCKET

Place the ice bucket (9) under the icemaker.

Make sure the icemaker power switch is set to O (off).

8

9

ATTACH WARRANTY LABEL

A label (7) is provided with this kit to record the

date of installation for warranty purposes. Apply it

to the back of the refrigerator.

9

KEEP THIS MANUAL

The warranty for the icemaker is printed in this

manual. Keep this manual with your Refrigerator

Owner’s Manual.

The icemaker installation inside the freezer is now

complete. Continue to the Water Valve Assembly

section.

10

11

Hook

20

Installation Instructions

BEFORE YOU BEGIN

Read each step thoroughly before proceeding.

•

CAUTION – Unplug the

Refrigerator. To eliminate the danger

of electric shock during installation,

you must unplug the refrigerator

from its electrical outlet.

WATER VALVE ASSEMBLY INSTALLATION INSTRUCTIONS N

Are these the right instructions for your model? Follow the Installation Instructions indicated by

the label on the back of the refrigerator --- or

RQPNML

Flat blade and Phillips

screwdrivers

Pliers

TOOLS YOU WILL NEED

Sharp knife

1/4″ and 5/16″ Nutdrivers

ATTACH THE WATER VALVE

• Locate the female connector plug. Plug the

female connector (C) onto the male terminals

on the water valve (3). Either wire can go on

either terminal.

2

10

• Fasten the water valve to the cabinet by driving

the hex-head screw (10) from the kit into the

hole in the cabinet leg.

C

3

REMOVE THE COVER

Use a 5/16″ nutdriver or an adjustable wrench to

remove the compressor compartment access cover.

This requires removing six screws which attach the

cover to the back of the refrigerator case.

Be sure to save the screws as the access cover must

be reinstalled later to ensure your refrigerator will

function properly.

1

La page charge ...

GE IM-4A Mode d'emploi

Ce manuel convient également à

GE IM-4A Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents