Panasonic PT-L780U Manuel utilisateur

R

Before operating this product, please read the instructions carefully and save this

manual for future use.

LCD Projector

Operating Instructions

Model No. PT-L780NTU

PT-L750U

R

TQBH9003-6

Commercial Use

2

IMPORTANT SAFETY NOTICE

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

Dear Panasonic Customer:

This instruction booklet provides all the necessary operating information that

you might require. We hope it will help you to get the most performance out

of your new product, and that you will be pleased with your Panasonic LCD

projector.

The serial number of your product may be found on its back. You should

note it in the space provided below and retain this booklet in case service is

required.

Model number: PT-L780NTU / PT-L750U

Serial number:

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the product.

Power Supply: This LCD Projector is designed to operate on 100 V – 240 V, 50 Hz/60

Hz AC, house current only.

CAUTION: The AC power cord which is supplied with the projector as an accessory can

only be used for power supplies up to 125 V, 10 A. If you need to use higher

voltages or currents than this, you will need to obtain a separate 250 V

power cord. If you use the accessory cord in such situations, fire may result.

3

Preparation

CAUTION: This equipment is equipped with a

three-pin grounding-type power

plug. Do not remove the grounding

pin on the power plug. This plug will

only fit a grounding-type power

outlet. This is a safety feature. If you

are unable to insert the plug into the

outlet, contact an electrician. Do not

defeat the purpose of the grounding

plug.

WARNING:

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Any unauthorised changes or modifications to this equipment

will void the users authority to operate.

Do not remove

Declaration of Conformity

Model Number: PT-L780NTU / PT-L750U

Trade Name: Panasonic

Responsible party: Matsushita Electric Corporation of America.

Address: One Panasonic Way Secaucus New Jersey 07094

Telephone number: 1-800-528-8601 or 1-800-222-0741

Email: [email protected]

This device complies with Part 15 of the FCC Rules, Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

4
Preparation
IMPORTANT SAFETY NOTICE..........2
Precautions with regard to safety ....6
Accessories......................................11
Precautions on handling.................12
Location and function of each part ...14
Using the remote control unit.........20
Laser beam pointer.........................20
Wireless mouse..............................21
Inserting the batteries.....................22
Operating range..............................22
Setting the projector IDs number for remote control unit 
...23
Connections .....................................24
Notes on connections.....................24
Example of connecting to video
equipment ...................................26
Example of connecting to computer ..27
Setting-up .........................................28
Projection methods.........................28
Projector position............................28
Projection distances .......................29
Basic Operation
Starting to use..................................30
Turning on the power......................30
Turning off the power......................31
On-screen menus.............................32
Menu screens.................................32
Menu operation guide.....................35
Returning to the previous screen....35
Returning a setting to the factory default 
...36
Using the freeze function................36
Using the D.ZOOM (digital zoom) function
...37
Adjusting the picture.......................38
PICTURE MODE............................38
Color Hue Setting ...........................39
COLOR...........................................39
TINT................................................39
BRIGHT..........................................39
CONTRAST....................................39
SHARPNESS .................................39
Noise Reduction(NR)......................39
TV SYSTEM ...................................39
WHITE BALANCE R/G/B ...............40
Projecting sRGB-compatible pictures 
...40
Adjusting the position.....................41
POSITION ......................................42
DOT CLOCK...................................42
CLOCK PHASE..............................42
KEYSTONE....................................42
OSD POSITION..............................43
ASPECT .........................................43
RESIZING.......................................44
AUTO SETUP.................................44
FRAME LOCK ................................44
Audio adjustment.............................45
VOLUME ........................................45
MUTE .............................................45
Changing the display language......45
Advanced Operation
Option settings.................................46
SHUTTER.......................................46
OSD................................................46
AUTO KEYSTONE.........................46
RGB/YPbPr ....................................46
RGB2 SELECT...............................46
BACK COLOR................................47
FRONT/REAR ................................47
DESK/CEILING ..............................47
LAMP POWER ...............................47
LAMP RUN TIME ...........................47
FAN CONTROL..............................47
WEB CONTROL.............................47
WEB STANDBY .............................47
WEB PASSWORD .........................48
CONTROL KEY..............................48
FUNC 1...........................................48
SET ID............................................48
AUTO POWER OFF.......................48
NETWORK SETUP ...........................49
SD CARD SETUP..............................49
Lens adjustment ..............................50
Projection lens replacement...........51
Projection distance for each 
projection lens (sold separately) 
..52
Slot cover replacement ...................54
Putting the power cord and 
remote control unit away.............55
Using the cable cover......................56
Using the remote terminal...............57
Using the SERIAL connector..........58
Others
Indicators..........................................60
About the automatic setup function......
62
List of compatible signals...............63
Cleaning and replacing the air filter...64
Replacing the lamp unit ..................65
Before calling for service................68
Specifications...................................70
Dimensions.......................................72
Trademark acknowledgements ......72
NOTES IMPORTANTES
CONCERNANT LA SÉCURITÉ
...73
Précautions de sécurité
..............74
Précautions de manipulation
.............78
Remplacement du bloc de lampe
...80
Contents

5
Preparation
Contents (Network Functions, SD Card Functions)
Other instructions .................84
Typical applications of SD card
/ network functions ...............88
Examples of use of SD card........... 88
Example of use of network 
functions ...................................... 89
Fitting and removal of SD card
and wireless card ..................90
SD card ............................................ 90
Wireless card/Projector LAN card.. 91
How to use SD card...............92
Replaying from recorded SD card
using the projector only.............. 92
Setting ........................................... 92
Replay ........................................... 93
Recording directly on SD card ...... 94
Compiling on Windows.................. 94
Compilation on Macintosh machine
.... 97
Network setting .....................99
Example of setting for use of the
wireless card................................ 99
To use wireless communication 
for the first time .......................... 99
If wireless communication has 
already been established between
PCs (in ad hoc mode) ............. 100
If wireless communication has 
already been established 
using an access point............... 101
If communication in ad hoc mode is
unavailable............................... 102
Example of setting for use of the
projector LAN card.................... 103
To directly connect a personal
computer to the projector ......... 103
When connecting via a relaying
device....................................... 103 
Setting up the projector ............... 104
Installing a wireless card driver .. 107
Fitting and removal of wireless card
into/from personal computer .... 107
Installing a driver ......................... 108
Settings of wireless card.............. 111
Settings of personal computer.... 112
TCP/IP setting ............................. 112
If two or more network devices 
are existent............................... 114
Web browser control...........116
What you can do with Web 
browser control ......................... 116
Settings of Web browser control
.... 116
Settings of projector..................... 116
Settings of personal computer..... 116
Operation of Web browser 
control ........................................ 117
Starting Web browser control ...... 117
Top screen................................... 117
Projector control .......................... 118
SD control.................................... 119
Changing password..................... 120
When using PDA......................120
Operation of PDA.....................120
Wireless Manager 2.0..........122
What you can do with Wireless
Manager 2.0................................ 122
Installation of Wireless Manager 2.0 
... 122
Before installation........................ 122
Procedure of installation.............. 122
Operation of Wireless Manager 2.0
.... 123
Starting/ending Wireless 
Manager 2.0............................. 123
Registration of projector .............. 123
To capture and transfer the 
image of PC screen.................. 125
Transfer of image stored in the
personal computer ................... 126
Major examples of usage ............. 129
Basic usage................................. 129
Automatic display in predefined
sequence.................................. 129
Quick-changing presentation using
SD card .................................... 129
Conference using multiple personal
computers ................................ 129
Image Creator 1.0 ................130
What you can do with Image 
Creator 1.0.................................. 130
Installation of Image Creator 1.0 
... 131
Before installation........................ 131
Procedure of installation.............. 131
Operation of Image Creator 1.0... 131
DCF standard .............................. 136
Before Placing an repair order .... 137
Explanation of terms .................... 139
Trademark Information................. 142
Consignes de sécurité.................. 143

6

Precautions with regard to safety

WARNING

If a problem occurs (such as no image or no sound) or if you notice

smoke or a strange smell coming from the projector, turn off the power

and disconnect the power cord from the wall outlet.

B Do not continue to use the projector in such cases, otherwise fire or

electric shocks could result.

B Check that no more smoke is coming out, and then contact an Authorised

Service Center for repairs.

B Do not attempt to repair the projector yourself, as this can be dangerous.

Do not install this projector in a place which is not strong enough to

take the full weight of the projector.

B If the installation location is not strong enough, it may fall down or tip over,

and severe injury or damage could result.

Installation work (such as ceiling suspension) should only be carried

out by a qualified technician.

B If installation is not carried out correctly, there is the danger that injury or

electric shocks may occur.

If foreign objects or water get inside the projector, or if the projector is

dropped or the cabinet is broken, turn off the power and disconnect the

power cord from the wall outlet.

B Continued use of the projector in this condition may result in fire or electric

shocks.

B Contact an Authorised Service Center for repairs.

Do not overload the wall outlet.

B If the power supply is overloaded (for example, by using too many

adapters), overheating may occur and fire may result.

Do not remove the cover or modify it in any way.

B High voltages which can cause fire or electric shocks are present inside

the projector.

B For any inspection, adjustment and repair work, please contact an

Authorised Service Center.

Clean the power cord plug regularly to prevent it from becoming

covered in dust.

B If dust builds up on the power cord plug, the resulting humidity can

damage the insulation, which could result in fire. Pull the power cord out

from the wall outlet and wipe it with a dry cloth.

B If not using the projector for an extended period of time, pull the power

cord plug out from the wall outlet.

7

Preparation

Do not do anything that might damage the power cord or the power

cord plug.

B Do not damage the power cord, make any modifications to it, place it near

any hot objects, bend it excessively, twist it, pull it, place heavy objects on

top of it or wrap it into a bundle.

B If the power cord is used while damaged, electric shocks, short-circuits or

fire may result.

B Ask an Authorised Service Center to carry out any repairs to the power

cord that might be necessary.

Do not handle the power cord plug with wet hands.

B Failure to observe this may result in electric shocks.

Insert the power cord plug securely into the wall outlet.

B If the plug is not inserted correctly, electric shocks or overheating could

result.

B Do not use plugs which are damaged or wall outlets which are coming

loose from the wall.

Do not place the projector on top of surfaces which are unstable.

B If the projector is placed on top of a surface which is sloped or unstable, it

may fall down or tip over, and injury or damage could result.

Do not place the projector into water or let it become wet.

B Failure to observe this may result in fire or electric shocks.

Do not place liquid containers on top of the projector.

B If water spills onto the projector or gets inside it, fire or electric shocks

could result.

B If any water gets inside the projector, contact an Authorised Service

Center.

Do not insert any foreign objects into the projector.

B Do not insert any metal objects or flammable objects into the projector or

drop them onto the projector, as doing so can result in fire or electric

shocks.

Keep the remote control unit out of the reach of children, and do not

look into the laser beam or point it towards other people.

B If the laser beam which is emitted by the remote control unit transmitter is

pointed directly into the eyes, it may cause visual ability to be impaired.

Do not allow the + and - terminals of the batteries to come into contact

with metallic objects such as necklaces or hairpins.

B Failure to observe this may cause the batteries to leak, overheat, explode

or catch fire.

B Store the batteries in a plastic bag and keep them away from metallic objects.

During a thunderstorm, do not touch the projector or the cable.

B Electric shocks can result.

Do not use the projector in a bath or shower.

B Fire or electric shocks can result.

8

Do not look into the lens while the projector is being used.

B Strong light is emitted from the projector’s lens. If you look directly into this

light, it can hurt and damage your eyes.

Do not bring your hands or other objects close to the air outlet port.

B Heated air comes out of the air outlet port. Do not bring your hands or

face, or objects which cannot withstand heat close to this port, otherwise

burns or damage could result.

When replacing the lamp, allow it to cool for at least one hour before

handling it.

B The lamp cover gets very hot, and contact with it can cause burns.

Before replacing the lamp, be sure to unplug the power cord from the

power outlet.

B Electric shocks or explosions can result if this is not done.

Keep the SD memory card out of the reach of infants. (PT-L780NTU only)

B If the memory card is swallowed, death by suffocation may result. If you

believe that the memory card may have been swallowed, seek medical

advice immediately.

Caution

Do not cover the air inlet or the air outlet.

B Doing so may cause the projector to overheat, which can cause fire or

damage to the projector.

Do not set up the projector in humid or dusty places or in places where

the projector may come into contact with smoke or steam.

B Using the projector under such conditions may result in fire or electric

shocks.

When disconnecting the power cord, hold the plug, not the cord.

B If the power cord itself is pulled, the cord will become damaged, and fire,

short-circuits or serious electric shocks may result.

Always disconnect all cables before moving the projector.

B Moving the projector with cables still attached can damage the cables,

which could cause fire or electric shocks to occur.

Do not place any heavy objects on top of the projector.

B Failure to observe this may cause the projector to become unbalanced

and fall, which could result in damage or injury.

Do not short-circuit, heat or disassemble the batteries or place them

into water or fire.

B Failure to observe this may cause the batteries to overheat, leak, explode

or catch fire, and burns or other injury may result.

When inserting the batteries, make sure the polarities (+ and -) are

correct.

B If the batteries are inserted incorrectly, they may explode or leak, and fire,

injury or contamination of the battery compartment and surrounding area

may result.

9

Preparation

Use only the specified batteries.

B If incorrect batteries are used, they may explode or leak, and fire, injury or

contamination of the battery compartment and surrounding area may

result.

Do not mix old and new batteries.

B If the batteries are inserted incorrectly, they may explode or leak, and fire,

injury or contamination of the battery compartment and surrounding area

may result.

Do not put your weight on this projector.

B You could fall or the projector could break, and injury may result.

B Be especially careful not to let young children climb onto the projector.

Disconnect the power cord plug from the wall outlet as a safety

precaution before carrying out any cleaning.

B Electric shocks can result if this is not done.

Ask an Authorised Service Center to clean inside the projector at least

once a year.

B If dust is left to build up inside the projector without being cleaned out, it

can result in fire or problems with operation.

B It is a good idea to clean the inside of the projector before the season for

humid weather arrives. Ask your nearest Authorised Service Center to

clean the projector when required. Please discuss with the Authorised

Service Center regarding cleaning costs.

We are constantly making efforts to preserve and maintain a clean

environment. Please take non repairable units back to your dealer or a

recycling company.

10

WARNING

Keep the SD memory card out of the reach of infants.

• If the memory card is swallowed, death by suffocation may result. If you

believe that the memory card may have been swallowed, seek medical

advice immediately.

Caution

Do not insert any foreign objects into the card slot.

• Inserting foreign objects may damage the projector. If the wireless card is

inserted while some foreign object is inside the slot, it may damage the

wireless card.

Notes with regard to the wireless card

and the projector.

Caution

Before touching the wireless card or the projector LAN card,

make sure that you earth your body to dissipate any static

electric charge that might damage the card.

• Static electricity from the human body can damage the wireless card. To

prevent this, you should touch a nearby metallic object such as an

aluminium sash or a door knob to dissipate the static charge from your

body.

Do not install the accessory wireless card or projector LAN card

to any device other than the card slot of the projector.

• If this is not observed, damage to the device may result.

11

Preparation

Slot cover (for projector LAN card)

(TKKL5243 x1)

(PT-L780NTU only)

Remote control unit

(N2QAEA000011 x1)

Power coed

(K2CG3FZ00008 x 1)

AAA batteries for

remote control unit (x2)

RGB signal cable [3.0 m

(9´10˝), K1HB15FA0001

x1]

Video/Audio cable [3.0

m (9´10˝),

K2KA2FA00001 x 1]

Accessories

Check that all of the accessories shown below have been included with your

projector.

CD-ROM (TQBH9003x1)

(PT-L780NTU only)

Protective case for SD memory card

(RP-SDCC0 x1)

(PT-L780NTU only)

Cable cover

(TXFKR01VJN1 x1)

SD memory card (8 MB,

RP-SD008BEZ0 x1)

(PT-L780NTU only)

USB cable

(3.0 m, K1HB04FD0002 x 1)

12

Precautions on handling

Cautions when moving the projector

Be sure to attach the lens cover before moving the projector.

The projection lens is extremely susceptible to vibration and shocks. Be

careful not to subject it to excessive vibration and shock when moving the

projector.

Cautions regarding setting-up

Observe the following at all times when setting up the projector.

Avoid setting up in places which are subject to vibration or shocks.

If the projector is set up in locations with strong vibration, such as near a

motor, or if it is installed inside a vehicle or on board a ship, the projector

may be subjected to vibration or shocks which can damage the internal parts

and cause malfunctions or accidents. Accordingly, set up the projector in a

place which is free from such vibrations and shocks.

Do not set up the projector near high-voltage power lines or near

motors.

The projector may be subject to electromagnetic interference if it is set up

near high-voltage power lines or motors.

If installing the projector to the ceiling, ask a qualified technician to

carry out all installation work.

If the projector is to be suspended from the ceiling, you will need to purchase

the separate installation kit (Model No.: ET-PK780). Furthermore, all

installation work should only be carried out by a qualified technician.

If using this projector at high elevations (above 1 400 m), set the FAN

CONTROL to HIGH. (Refer to page 47.)

Failure to observe this may result in malfunctions.

Notes on use

In order to get the best picture quality

If outside light or light from indoor lamps is shining onto the screen, the

images projected will not have good contrast. Draw curtains or blinds over

any windows and turn off any fluorescent lights near the screen to prevent

reflection.

Do not touch the surfaces of the lens with your bare hands.

If the surface of the lens becomes dirty from fingerprints or anything else, this

will be magnified and projected onto the screen. Moreover, when not using

the projector, retract the lens and then cover it with the accessory lens cover.

13

Preparation

About the screen

If the screen you are using is dirty, damaged or discolored, attractive

projections cannot be obtained. Do not apply any volatile substances to the

screen, and do not let it become dirty or damaged.

About the lamp

The lamp may need to be replaced earlier due to variables such as a

particular lamp’s characteristics, usage conditions and the installation

environment, especially when it is subjected to a continuous use for more

than 10 hours.

About the SD memory card (PT-L780NTU only)

Static electricity from the human body can damage the SD memory card. To

prevent this, you should touch a nearby metallic object such as an aluminium

sash or a door knob to dissipate the static charge from your body.

About the card slot (PT-L780NTU only)

Make sure that there are no foreign objects inside the slot when inserting the

SD memory card or an optional wireless card. Failure to observe it may

damage the card and the slot.

Before carrying out cleaning and maintenance, be

sure to disconnect the power cord plug from the

wall outlet.

Wipe the cabinet with a soft, dry cloth.

If the cabinet is particularly dirty, soak the cloth in water with a small amount

of neutral detergent in it, squeeze the cloth very well, and then wipe the

cabinet. After cleaning, wipe the cabinet dry with a dry cloth.

If using a chemically-treated cloth, read the instructions supplied with

the cloth before use.

Do not wipe the lens with a cloth that is dusty or which produces lint.

If any dust or lint gets onto the lens, such dust or lint will be magnified and

projected onto the screen. Use a blower to clean any dust and lint from the

lens surface, or use a soft cloth to wipe off any dust or lint.

14

Location and function of each part

# Projector control panel

(page 16)

$ Focus ring

(pages 31 and 50)

% Air inlet ports

Do not cover these ports.

& Leg adjuster buttons(L/R)

(page 30)

These buttons are used to unlock

the front adjustable legs. Press to

adjust the angle of tilt of the

projector.

' Front adjustable legs(L/R)

(page 30)

( Lens release button

(page 51)

This button is used when using a

projection lens that is sold

separately.

) Projection lens

* Lens cover

+ Remote control signal receptor

(page 22)

, Air filter

(page 64)

- Connector panel

(page 18)

. Power input socket (AC IN)

(page 30)

The accessory power cord is

connected here.

Do not use any power cord other

than the accessory power cord.

/ MAIN POWER switch

(pages 30 and 31)

0 Speaker

Projector <Top, right and front>

#

$

'

(

)

&

'

+*

,

%

/

0

.

&

-

15

Preparation

# Remote control signal receptor

(page 22)

$ Security lock

This can be used to connect a

commercially-available theft-

prevention cable (manufactured

by Kensington). This security lock

is compatible with the Microsaver

Security System from

Kensington. Contact details for

this company are given below.

Kensington Technology Group

ACCO Brands Inc.

2855 Campus Drive

San Mateo, CA 94403 USA

Tel (650)572-2700

Fax (650)572-9675

http://www.kensington.com/

http://www.gravis.com/

NOTE:

B Information given above may be

changed in future.

% Carrying handle

& Lamp unit holder

(page 65)

' Air outlet port

Do not cover this port.

WARNING

Do not bring your hands or other

objects close to the air outlet

port.

B Heated air comes out of the air

outlet port. Do not bring your

hands or face, or objects which

cannot withstand heat close to

this port, otherwise burns or

damage could result.

NOTE:

B During projection of an image, the

cooling fan will operate, emitting

a small noise as it operates.

Turning the lamp on or off will

cause this noise to increase a

little.

B By using the OPTION menu to

set “LAMP POWER” to

“

LOW

”

,

the operating sound of the fan

can be reduced. (Refer to page

47.)

Projector <Back and bottom>

&

$

%

#

'

16

Remote control unit

# Power indicator

(pages 30, 31 and 47)

This indicator illuminates red when

the MAIN POWER switch is turned

on (standby mode), and illuminates

green when the power is turned on

and a picture starts to be projected.

(PT-L780NTU only)

When the WEB STANDBY is set

to "ON", the cooling fan operates

and the power indicator on the

projector flashes slowly in red.

$ RGB INPUT indicator

This indicator illuminates when a

signal is input into the connector

that is selected with the input

select buttons.

%LAMP indicator (page 61)

This indicator illuminates when it is

time to replace the lamp unit. It flashes

if a circuit abnormality is detected.

& Input select (RGB, VIDEO)

buttons (page 30)

'TEMP indicator (page 60)

This indicator illuminates if an

abnormally high temperature is

detected inside the projector or

around it. If the temperature rises

above a certain level, the power

supply will be turned off

automatically and the indicator

will illuminate or flash.

( POWER button

(pages 30 and 31)

) AUTO SETUP button

(pages 30 and 62)

If this button is pressed while a

picture is being projected, the

projection settings will be

adjusted automatically in

accordance with the signal being

input. In addition, the angle of tilt

of the projector will be

automatically detected and

adjusted in order to correct any

keystone distortion. (“AUTO

SETUP” will appear on the

screen during adjustment.) Set

“AUTO KEYSTONE” in the

OPTION menu to “OFF” to

prevent any deterioration of the

picture as a result of keystone

correction. However, keystone

distortion may not be corrected

RGBVIDEOAUTO SETUP

ON(G)

STANDBY(R)

ENTER

MENU

POWER SHUTTER

INPUT

TEMP

LAMPRGB INPUT

– FOCUS +

–

ZOOM +

POWER

RGB

VIDEO

R-CLICK

LASER

MENU

PA GE

ENTER

FREEZE SHUTTER

FUNC1

Computer Pro jector

SETUP

AUTO

(

&

)

4

5

+

3

,

-

6

*

:

7

8

9

;

0

12

'

&

%

$

+,

-

*

#

(

)

/

.

Projector control panel

17
Preparation
properly when using a lens that is
sold separately. Refer to page 42
for details on correcting keystone
distortion manually.
*SHUTTER button (page 46)
This button is used to
momentarily turn off the picture
and sound. However, keystone
distortion may not be corrected
properly when using a lens that is
sold separately. Refer to page 42
for details on correcting keystone
distortion manually.
+MENU button (pages 32 and 35)
This button is used to display the
menu screens. When a menu
screen is being displayed, this
button can be used to return to a
previous screen or to clear the
screen.
, Arrow (
FFGGII
and 
HH
) buttons
(page 35)
These buttons are used to select
and adjust items in the menu
screens.
*When in computer operating
mode, these buttons on the
remote control unit function
differently. (page 21)
-ENTER button (page 35)
This button is used to accept and
to activate items selected in the
on-screen menus.
*When in computer operating
mode, this button on the remote
control unit operates differently.
(page 21)
.FOCUS +/- buttons (page 31)
These buttons are used to adjust
the projected image focus.
/Zoom +/- buttons (page 31)
These buttons are used to adjust
the projected image size.
0Laser emitter (page 20)
1Infrared emitter (page 22)
2Click button (page 21)
This button can be used when the
operating mode select switch is
moved to the left (Computer).
3PAGE button (page 21)
This button can be used when the
operating mode select switch is
moved to the left (Computer).
4Operation indicator (page 20)
This indicator illuminates while a
laser beam is being emitted
(while the LASER button is being
pressed). It flashes when any
other buttons are being pressed.
5LASER button (page 20)
A beam of laser light is emitted while
this button is being pressed. This
laser beam can be used as a pointer
to point to something on the screen.
6FREEZE button (page 36)
This button is used to
momentarily freeze projection so
that a still picture is displayed.
7D.ZOOM +/- buttons (page 37)
These buttons are used to
enlarge the projected image.
8 VOLUME +/- buttons
These buttons are used to adjust
the volume of the sound output
from the projector’s built-in
speakers. Refer to page 45 for
details on how to adjust the
volume using the buttons on the
projector control panel.
9 FUNCTION (FUNC1) button
(pages 42, 45 and 48)
This button can be used for 1)
switching on and off the sound
volume and 2) entering into the
keystone distortion correction mode.
Use the FUNC1 item in the OPTION
menu to select which you wish to use.
:ID SET button (page 23)
This button is used to set the IDs
into the remote control unit when
using multiple projectors with a
single remote control unit.
; Operating mode (Computer,
Projector) select switch
(page 21)
Move this switch to the left side to
use the remote control unit to
operate a computer, and move it
to the right side to operate the
projector.

18

USB

DVI-D IN

REMOTE

SERIAL

RGB1 IN

RGB2 IN/RGB OUT

AUDIO OUT

RGB AUDIO IN

VIDEO IN

AUDIO IN

S-VIDEO IN

R

L

R/R-Y/P

R VDSYNC/HDB/B-Y/PB

RGB3 IN

G/Y

'

& ( )%$#

, - .+

*

# USB port

(page 21)

The remote control unit can be

used as

a personal computer

mouse by connecting the

projector to

a personal computer

with the supplied USB cable.

(4-pin square connector)

$ SERIAL connector

(pages 26, 27 and 58)

This connector is used to connect

a personal computer to the

projector in order to externally

control the projector. (RS-232C

compatible)

% RGB1 IN connector

(pages 26 and 27)

This connector is used to input

RGB signals and YPBPR signals.

& RGB2 IN/RGB OUT connector

(pages 26 and 27)

This connector is used to input or

output RGB signals and YPBPR

signals. Use the RGB2 SELECT

item in the OPTION menu to

select whether you want input or

output with this connector.

' DVI-D IN connector

(page 27)

This connector is used to input

DVI-D signals.

( AUDIO OUT jack

(pages 26 and 27)

This jack is used to output the

audio signals which are input to

the projector. If audio equipment

is connected to this jack, no

sound will be output from the

built-in speakers.

) S-VIDEO IN connector

(pages 26 and 44)

This connector is used to input

signals from a S-VIDEO-

compatible equipment such as a

video deck. The connector is S1

signal compatible, and it

automatically switches between

16:9 and 4:3 aspect ratios in

accordance with the type of

signal being input.

* AUDIO IN L-R (for VIDEO/S-

VIDEO) jacks

(page 26)

Only one system is provided, so

connect the appropriate

connector when using VIDEO or

S-VIDEO.

+ Remote control connector

(page 57)

This connector is used to control

the projector from the Remote

Control set up in Wired mode.

, RGB3 (YPBPR) IN connector

(pages 26 and 27)

This connector is used to input

LOCK

)

(

19

Preparation

'% &

$

#

Front Back

# Slot cover

Covers the card slots. When

using an optional projector LAN

card, replace the slot cover (refer

to page 54).

$ Card slot

Insert an optional wireless card or

a projector LAN card into here.

% Eject switch

Use to remove an optional

wireless card or projector LAN

card from the card slot.

& Access lamp

Flashes while the projector is

being accessed for reading or

writing the data in the SD

memory card.

' SD memory card slot

Insert the SD memory card into

here.

( Metal terminals

These terminals are for

connecting the SD memory card

to the projector’s card slot. Do not

touch the metal terminals with

hands or metal objects, attach

stickers to them, or allow them to

become contaminated in any

way.

) Write-protect switch

If the write-protect switch on the

SD memory card is moved to the

LOCK position, it will not be

possible to use any file editing

functions such as deleting or

moving image files.

(PT-L780NTU only)

RGB signals and YPBPR signals.

- RGB AUDIO IN jack

(pages 26 and 27)

Only one system is provided, so

connect the appropriate

connector when using RGB1,

RGB2 or RGB3.

. VIDEO IN jack

(page 26)

This jack is used to input video

signals from a video equipment

such as a video deck.

20

Using the remote control unit

PUSH

Laser beam pointer

The laser beam emitted from the remote control can be used as a pointer by

pointing forward to the screen.

While the LASER button is being pressed, the laser beam is being emitted

and the operating indicator illuminates.

Do not look into the laser emitter of the remote control unit or point the laser

beam towards other people, otherwise damage to eyes may occur.

Caution

B Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous

radiation exposure.

B This remote control unit cannot be repaired.

N2QAEA000011

La page charge ...

Panasonic PT-L780U Manuel utilisateur

Panasonic PT-L780U Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents