Lifetime 90698 Le manuel du propriétaire

Taper
Le manuel du propriétaire
Lifetime’s assembly experts offer quick responses and great customer service.
POWER LIFT
®
BASKETBALL SYSTEM
Icon Legend................................2
Notices....................................3
Ground Preparation.....................4
Pole Assembly.............................9
Backboard to Rim Assembly.......14
Backboard to Pole Assembly......20
Parts Identifi er..........................i-iv
Handle Assembly.......................29
Final Assembly..........................36
Maintenance Instructions..........43
Registration...........................43
Warning Sticker........................44
Warranty................................47
Call: 1-800-225-3865
7:00 am–5:00 pm (Monday–Friday) MST
and 9:00 am–1:00 pm Saturday MST
Web: www.lifetime.com/instructions
Live Chat: www.lifetime.com/instructions
NEED HELP? TALK TO US!
MODEL# AND PRODUCT ID (you will need both when contacting us)
Model Number: Product ID:
Lifetime basketball systems are designed to be
strong and durable. We strive to make assembly as
easy as possible without compromising quality. If
you get stuck, we have tools to help:
Prepare the Area
Before you start, you will need at least six 80-lb.
bags of concrete mix. Before digging, call to locate
any buried utility lines.
Recruit Friends and Family
Assembly should take 3 people about 3–4
hours to complete.
Save this instruction in the event that the manufacturer
has to be contacted for replacement parts.
TOOLS REQUIRED TABLE OF CONTENTS
90698
(2) (2) (2)
(1)
(1)
(1)
(1)
3/4” (19 mm) 11/16” (18 mm) 9/16” (14 mm)
(1)
(1)
(1)
(2)
1/2” (13 mm)
(1)
Cement
6-90-lb. bags
(1)
30” (762 mm)
Rebar
(1)
(1)
COPY
2
1172647_D
7/22/2016
COPY
3
WARNINGS & NOTICES
4
1
GROUND PREPARATION
Metal Parts
TOOLS REQUIRED
PARTS REQUIRED
HARDWARE REQUIRED
(1)
(1)
ALE (x1)
30” Rebar
Cement Mix
Level
BGW (x1)
Paper Parts
(1)
5
TOOLS AND HARDWARE REQUIRED
X SECTION 1 (CONTINUED)
1.1
A Ground Sleeve is available as an
alternative to cementing the Pole into the
ground. Please contact Customer Service for
more information.
!
Dig a round hole 24” deep and 21” in diameter. If you live in an area where frost heaves may pose a problem,
consult your local building inspector to determine the proper hole depth. The edge of the hole should be fl ush
with the edge of the playing surface.
6
TOOLS AND HARDWARE REQUIRED
X SECTION 1 (CONTINUED)
Make a mark 16 inches from the dimpled end of the Bottom Pole (ALE) (do not scratch the powder coating). Slide
the Alignment Frame (BGW) over the Bottom Pole.
Mix 5 1/2 bags of concrete. Save 1/2 bag of concrete mix to use later in the assembly. Pour the mixed
concrete into the hole until it is fi lled to the level of the playing surface.
1.2
1.3
(9 Bags, 80 lb each)
ALE
16”
ALE
BGW
7
TOOLS AND HARDWARE REQUIRED
X SECTION 1 (CONTINUED)
Slide the dimpled end of the Bottom Pole (ALE) into the cement up to the 16-inch mark. Position the pole next to
the playing surface. For regulation courts, the Alignment Frame (BGW) should cross the playing surface at the middle
of the scored measurements.
1.4
Use a Level to make sure the Bottom Pole is standing vertical. Form
the cement into a downward slope away from the pole to allow water
runoff. Failure to do so may result in premature rusting of the Pole.
If the pole is buried too deep or too shallow,
the rim will not to be at the correct height.
Do not continue the assembly until the concrete
has been allowed to set for 1-4 hours.
!
!
!
30” Rebar
Playing
Surface
ALE
TOP VIEW
BGW
ALE
Rebar
Insert the 30” rebar (not included) inside the Bottom Pole (ALE) so it is about 15” from the top of the pole. Check
the pole several times within the fi rst hour to make sure that all sides are vertical and that the 16-inch mark remains level with the
surface.
1.5
8
TOOLS AND HARDWARE REQUIRED
X SECTION 1 (CONTINUED)
Mix the remaining 1/2 bag of concrete. Fill the Bottom Pole (ALE) with concrete until it reaches the top of the
rebar (about 15” from the top of the pole). Tamp the concrete down in the Bottom Pole with a broom handle to
remove air pockets. Clean all concrete off the outside of the pole. You may now remove the Alignment Frame (BGW).
1.6
15”
Stop assembly now. Do not continue the assembly until the concrete has been allowed
to set for at least 72 hours (3 days). In humid climates or wet weather, allow more time
for the concrete to cure. Do not proceed until the curing process is complete.
!
9
2
POLE ASSEMBLY
Metal Parts
Hardware Bag
TOOLS REQUIRED
PARTS REQUIRED
HARDWARE REQUIRED
ALF (x1)
CMV (x2)
AAA (x2)
AAF (x2)
ANF (x2)
ANE (x2)
5”
(Not actual length)
ALL (x1)
ALH (x1)
ALM (x1)
BCO
10
TOOLS AND HARDWARE REQUIRED
X SECTION 2 (CONTINUED)
AAF (x2)
ANF (x2)
ANE (x2)
5”
(Not actual length)
2.1
ANF
AAF
ANE
Large holes
Small holes
ALH
After allowing the concrete to cure for at least 72 hours, insert the Hex Bolts (ANF) with the Washers (AAF) into
the Top Pole (ALH) as shown. Then slide the Spacers (ANE) onto the Hex Bolts.
11
TOOLS AND HARDWARE REQUIRED
X SECTION 2 (CONTINUED)
AAA (x2)
9/16" (x2)
2.2
• Place the Pole Bracket (ALL) onto the Hex
Bolts (ANF), and attach it to the Top Pole
(ALH) with the hardware shown.
ALH
ALL
AAA
ANF
Insert the slotted end of the Middle Pole (ALF) into
the fl ared end of the Top Pole (ALH). Make sure the
poles are oriented as shown.
ALF
ALH
2.3
• Make sure the Warning Sticker and the Pole Bracket face
opposite directions.
!
12
TOOLS AND HARDWARE REQUIRED
X SECTION 2 (CONTINUED)
2.4
If the Top Pole (ALH) does not completely cover the slots on the Middle Pole (ALF)
after seating, DO NOT COMPLETE ASSEMBLY. Call our Customer Service Department.
In order to seat the Poles, strike each end of the Pole very hard fi ve to six times on a piece of scrap wood or cardboard.
This must be done even if the Poles cover the slot before seating has occurred.
!
ALF
ALH
Do not hit your feet with the Pole sections, as serious injury could occur.
!
WARNING
The Poles must be seated together! Even if the Poles cover
the slots before seating, they must be struck on a hard
surface fi ve to six times! Failure to seat the Poles correctly
could allow the Poles to separate during use, which could
lead to serious personal injuries or property damage.
13
TOOLS AND HARDWARE REQUIRED
X SECTION 2 (CONTINUED)
2.5
CMV (x1)
After the Poles have been seated, measure up one inch from the bottom center of the Top Pole (ALH) and insert
one Self-Drilling Screw (CMV) into the back of the Pole as shown. Then insert the Pole Cap (ALM) into the Top Pole.
Save the remaining Screw for use in Section 5.
ALH
ALF
CMV
1” up from
bottom of
Top Pole
CMV
Chuck the Self-Tapping Screw directly into an Electric Drill for easy installation, or
use a 3/8” Hex Driver.
!
ALH
ALM
14
15
16
17
18
19
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50

Lifetime 90698 Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues