Hatco CSUR, CSBFR, CSSBR, CSSBFR, CSUX, CSBFX, CSSBX, CSSBFX Series Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
P/N 07.04.835.00 © 2020 Hatco Corporation
hatcocorp.com
Register Online!
(see page 2)
S’inscrire en ligne!
(voir page 28)
Do not operate this equipment unless you
have read and understood the contents
of this manual! Failure to follow the
instructions contained in this manual
may result in serious injury or death.
This manual contains important safety
information concerning the maintenance,
use, and operation of this product. If
you’re unable to understand the contents
of this manual, please bring it to the
attention of your supervisor. Keep this
manual in a safe location for future
reference.
English = p 2
WARNING
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en
este manual puede resultar en un serio
lesión o muerte. Este manual contiene
importante información sobre seguridad
concerniente al mantenimiento, uso y
operación de este producto. Si usted
no puede entender el contenido de
este manual por favor pregunte a su
supervisor. Almacenar este manual en
una localización segura para la referencia
futura.
ADVERTENCIA
Ne pas utiliser cet équipement sans avoir
lu et compris le contenu de ce manuel ! Le
non-respect des instructions contenues
dans ce manuel peut entraîner de
graves blessures ou la mort. Ce manuel
contient des informations importantes
concernant l’entretien, l’utilisation et le
fonctionnement de ce produit. Si vous ne
comprenez pas le contenu de ce manuel,
veuillez le signaler à votre supérieur.
Conservez ce manuel dans un endroit
sûr pour pouvoir vous y référer plus tard.
Français = p 28
AVERTISSEMENT
Remote Built-In Cold Shelves
Plaques réfrigérantes encastrables
contrôlées à distance
CSUR, CSBFR, CSSBR, CSSBFR, CSUX,
CSBFX, CSSBX, and CSSBFX Series/Série
Installation and Operating Manual
Manuel d’installation et d’utilisation
2
Form No. CSRM-0220
English
INTRODUCTION
Important Owner Information ..............................................2
Introduction ...........................................................................2
Important Safety Information ..............................................3
Model Designation ...............................................................4
Model Description ................................................................5
Specifications .......................................................................6
Refrigerant Information ........................................................6
Electrical Rating Charts ....................................................... 6
Dimensions ........................................................................ 10
Installation ...........................................................................13
General .............................................................................. 13
Preparing the Installation Site ...........................................13
Installing a Top Mounted Unit ............................................ 14
Countertop Cutout Dimensions—Top Mounted Units .......14
Countertop Cutout and Mounting Bolt Dimensions—
Bottom Mounted Units .....................................................15
Installing a Bottom Mounted Unit ......................................16
Installing an Under Mounted Unit ...................................... 17
Mounting Bolt Dimensions .................................................19
Connecting the Components ............................................. 20
Installing the Remote Control Box .....................................21
Operation .............................................................................22
General .............................................................................. 22
Changing the Setpoint Temperature ..................................23
Setting the Auto-Defrost Cycle ..........................................23
Changing Fahrenheit and Celsius Setting .........................23
Maintenance ........................................................................24
General .............................................................................. 24
Daily Cleaning ...................................................................24
Cleaning the Stone Surface
(CSSB and CSSBF Models) ...........................................25
Monthly Cleaning ...............................................................25
Troubleshooting Guide ......................................................26
Options and Accessories ..................................................27
Limited Warranty ................................................................27
Authorized Parts Distributors ...........................Back Cover
IMPORTANT OWNER INFORMATION
Record the model number, serial number, voltage, and
purchase date of the unit in the spaces below (specification
label located on the side of the control box). Please have this
information available when calling Hatco for service assistance.
Model No. ________________________________________
Serial No. _________________________________________
Voltage ___________________________________________
Date of Purchase ___________________________________
Register your unit!
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the Hatco website at
www.hatcocorp.com, select the Support pull-down menu,
and click on “Warranty”.
Business
Hours: 7:00 to 5:00 Monday–Friday,
Central Time (CT)
(Summer Hours — June to September:
7:00 to 5:00 Monday–Thursday
7:00 to 4:00 Friday)
Telephone: 800-558-0607; 414-671-6350
E-mail: [email protected]
24 Hour 7 Day Parts and Service
Assistance available in the United States
and Canada by calling 800-558-0607.
Additional information can be found by visiting our web site at
www.hatcocorp.com.
Hatco Remote Built-In Cold Shelves are specially designed to
hold chilled foods at safe serving temperatures. The insulated,
top mount or bottom mount units are available in several sizes.
The components of the Remote Cold Shelves are shipped as
separate pieces that require field installation and connection.
This provides the end user greater installation flexibility than
self-contained units. The components include a cold shelf, a
control panel, and a condensing unit. One year parts and on-
site labor warranty is standard.
Hatco Remote Built-In Cold Shelves are products of extensive
research and field testing. The materials used were selected
for maximum durability, attractive appearance, and optimum
performance. Every unit is inspected and tested thoroughly
prior to shipment.
This manual provides the installation, safety, and operating
instructions for Remote Built-In Cold Shelves. Hatco
recommends all installation, operating, and safety instructions
appearing in this manual be read prior to installation or
operation of the unit.
Safety information that appears in this manual is identified by
the following signal word panels:
WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to
personal injury.
CONTENTS
Form No. CSRM-0220
3
English
IMPORTANT SAFETY INFORMATION
WARNING
ELECTRIC SHOCK HAZARD:
• Units supplied without an electrical cord and plug
require a hardwired connection to on-site electrical
system. Connection must be properly grounded and
of correct voltage, size, and configuration for electrical
specifications of unit. Contact a qualified electrician to
determine and install proper electrical connection.
• Unit must be installed by qualified, trained installers.
Installation must conform to all local electrical and
plumbing codes. Installation by unqualified personnel
will void the unit warranty and may lead to electric
shock or burn, as well as damage to unit and/or its
surroundings. Check with local plumbing and electrical
inspectors for proper procedures and codes.
• Turn OFF power switch and disconnect unit from power
source before performing any cleaning, adjustments,
or maintenance.
• Unit is not weatherproof. Locate unit indoors.
• Control box must be mounted in a vertical surface.
Mounting control box in a horizontal surface may result
in the collection of liquids and lead to electric shock.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• This unit is not “jet-proof” construction. Do not use
jet-clean spray to clean this unit.
• Do not steam clean or use excessive water on unit.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAZARD:
• Installcondensingunitwithaminimumof2″(51mm)
of space between all sides of unit and any combustible
surfaces.
• Do not use flammable cleaning solutions to clean this
unit.
EXPLOSION HAZARD: Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or
any other appliance.
Make sure food product and food pans have been chilled
to the proper food-safe temperature before placing on
unit. Failure to chill food product properly may result in
serious health risks. This unit is for holding pre-chilled
food product only.
WARNING
This unit is for holding food for short periods of time.
Never hold food longer than 4 hours.
Hatco Corporation is not responsible for actual food
product serving temperature. It is the responsibility of the
user to ensure that food product is held and served at a
safe temperature.
Maintain proper cleanliness of unit. Proper cleanliness and
sanitation is critical for food-safe operation. Refer to the
MAINTENANCE section for cleaning procedures.
Do not place food product directly onto hardcoat or
simulated stone surface. Food product must be wrapped,
boxed, or on a food pan.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them
away from the unit.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
CAUTION
Locate the unit at proper counter height in an area that is
convenient for use. The location should be level and strong
enough to support the weight of the unit and contents.
DO NOT tip unit/mounting surface after final installation.
Unit is free-floating and could fall out if tipped—for
permanent, horizontal installations only.
Make sure to clean and sanitize stone surface properly
after deep cleaning the surface using abrasives and before
placing food product on unit.
NOTICE
This unit is designed for use in environments where
ambient temperature is between 65°F (18°C) and 86°F
(30°C).
When shipped during cold weather months, store unit
for at least 10 hours in an environment where ambient
temperature is between 65°F (18°C) and 86°F (30°C) to
prevent compressor and/or refrigerant line damage. If unit
is turned on and there is excessive noise and vibration,
turn off immediately and allow additional warmup time.
Provide louvered or grill-style openings with a minimum
size of 12″ x 12″/144 square inches (31 x 31 cm/
961 square cm) in the cabinetry in front of and behind the
condensing unit for proper ventilation. Failure to provide
adequate air flow through the condensing unit may cause
unit failure and will void the unit warranty.
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
4
Form No. CSRM-0220
English
IMPORTANT SAFETY INFORMATION
MODEL DESIGNATION
C S B R - x x - x
Cold Shelf
B = Hardcoat Surface, Built-In, Bottom-Mount
SBF = Stone Surface, Built-In, Top-Mount
U = Under Counter-Mount
Cooled Width of Shelf (inches)
Cooled Depth of Shelf:
F = 15-1/2" (394 mm)
I = 19-1/2" (495 mm)
S = 24" (610 mm)
C S S B R - x x x x
Cold Shelf
Stone Surface, Built-In, Bottom-Mount
Width of Shelf (inches)
Depth of Shelf (inches)
R = w/ Remote Condensing Unit
X = Shelf Only
R = w/ Remote Condensing Unit
X = Shelf Only
NOTICE
Do not recirculate exhaust air inside cabinet when multiple
condensing units are installed together. Intake air should
enter from outside of cabinet.
Transport and install unit in upright position only. Failure
to do so may result in damage to the refrigeration system.
Use caution and avoid hitting condensing unit hoses/lines
when installing unit. Damage caused during installation is
not covered under warranty.
Do not locate unit in area with excessive air movement
around unit. Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods, air
conditioning ducts, and exterior doors).
Do not locate unit in an area subject to excessive
temperatures or grease from grills, fryers, etc. Excessive
temperatures could cause damage to the unit.
NOTICE
Damage to any countertop material caused by heat or cold
generated from Hatco equipment is not covered under
the Hatco warranty. Contact manufacturer of countertop
material for application information.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch the finish of the unit,
marring its appearance and making it susceptible to soil
accumulation.
Do not use steel wool for cleaning. Steel wool will scratch
the finish.
Do not use harsh chemicals such as bleach, cleaners
containing bleach, or oven cleaners to clean the unit.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
This unit is intended for commercial use only—NOT for
household use.
Form No. CSRM-0220
5
English
MODEL DESCRIPTION
All Models
Hatco Remote Built-In Cold Shelves are reliable and versatile.
Each unit has an insulated, stainless steel and aluminized
steel housing. A copper evaporator coil wound under the entire
hardcoat aluminum or stone surface provides even chilling
from edge to edge. Hatco Remote Cold Shelves are designed,
manufactured, and tested to maintain safe food holding
temperatures.
Controls for the Built-In Cold Shelves are housed in a single,
remote-mountable control box. They include a Power I/O (on/
off) Switch and a digital temperature controller. The control box
is field connected to the shelf and the condensing unit (remote
condensing unit models only).
Depending on the model, Built-In Cold Shelves are designed to
be mounted to the top side, bottom side, or underneath various
types of countertop material including stainless steel, wood,
Corian, and Swanstone.
The ecoization logo identifies products designed to reflect
Hatco’s commitment to improving, protecting, and preserving
the global environment. Hatco Remote Built-In Cold Shelves
qualify for the ecoization logo through the use of eco-friendly
insulation as well as a highly efficient condensing unit.
NOTE: Stone surfaces are a simulated stone solid surface.
CSBFR Models
CSBFR models have a hardcoat aluminum surface and are
top mounted.
CSSBR and CSSBFR Models
CSSBR and CSSBFR models have a decorative stone surface
and are bottom mounted.
CSUR Models
CSUR models have an aluminum surface and are mounted
directly against the underside of a granite or quartz countertop
(no cutout required). Cooling transfers through the countertop
to the top side for a true, seamless installation.
NOTE: For CSBFR, CSSBR, CSSBFR, and CSUR models,
all plumbing and electrical connections between the
components as well as to the electrical supply are the
responsibility of the end user and a qualified installer.
CSBFX Models
CSBFX models have a hardcoat aluminum surface and are top
mounted. They are not supplied with a condensing unit.
CSSBX and CSSBFX Models
CSSBX and CSSBFX models have a decorative stone
surface and are bottom mounted. They are not supplied with a
condensing unit.
CSUX Models
CSUX models are similar to CSUR models, but are not supplied
with a condensing unit.
NOTE: CSBFX, CSSBX, CSSBFX, and CSUX models must
be connected to an end user-supplied condensing unit.
All plumbing and electrical connections between the
components as well as to the electrical supply are the
responsibility of the end user and a qualified installer.
Condensing Unit
(CSBFR, CSSBR, CSSBFR,
and CSUR Models only)
CSBFR-48-S/CSBFX-48-S
CSUR-48-S/CSUX-48-S
CSSBR-4818/CSSBX-4818
Control Panel
(All Models)
6
Form No. CSRM-0220
English
Model
Compressor
Size Volts Hertz Watts Amps
Shipping
Weight
CSSBR-2418 1/5 hp 120 60 300 3.8
105 lbs. (48 kg)
1/3 hp 220/230/240
50 1089/1190/1296 5.0/5.2/5.4
60 1129/1234/1344 5.1/5.4/5.6
CSSBR-3018 1/5 hp 120 60 300 3.8
131 lbs. (59 kg)
1/3 hp 220/230/240
50 1089/1190/1296 5.0/5.2/5.4
60 1129/1234/1344 5.1/5.4/5.6
CSSBR-3618 1/5 hp 120 60 300 3.8
149 lbs. (68 kg)
1/3 hp 220/230/240
50 1089/1190/1296 5.0/5.2/5.4
60 1129/1234/1344 5.1/5.4/5.6
CSSBR-4818 1/3 hp 120 60 450 5.9
171 lbs. (78 kg)3/8 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
1/3 hp 60 1129/1234/1344 5.1/5.4/5.6
Electrical Rating Chart — CSSBR Models
NOTE: Shipping weights include packaging and are estimated.
The shaded areas contain electrical information for International models only.
SPECIFICATIONS
Models Fill Weights
CSBFR / CSSBFR / CSUR
-24-F, -24-I, -36-I, -36-S,
-48-F, -48-I
1 lb 13 oz
CSBFR / CSSBFR / CSUR
-24-S, -36-F
1 lb 15 oz
CSBFR / CSSBFR / CSUR
-48-S
2 lbs 8 oz
Discharge
Pressure
Suction
Pressure Superheat Subcooling
115 to 125 psig
(7.9 to 8.6 bar)
6 to 9 psig
(0.4 to 0.6 bar)
4° to 10°F
(2.2° to 5.6°C)
5° to 10°F
(2.8° to 5.6°C)
Remote Unit Fill Weights
NOTE: The Operating Specifications are accurate for units in an ambient
air temperature of 75°F (24°C).
High Side Low Side
186 psig
(12.8 bar)
88 psig
(6.07 bar)
Design Pressure
Operating Specifications
Refrigerant Information
All Hatco Remote Cold Shelves use R513A refrigerant in the
condensing unit.
Volts Hertz Watts Amps
120 60 12 0.1
220/230/240 50 17
0.1
60 12
Electrical Rating Chart — Solenoid Valve
(CSBFX, CSSBX, CSSBFX, and CSUX Models)
Form No. CSRM-0220
7
English
NOTE: Shipping weights include packaging and are estimated.
The shaded areas contain electrical information for International models only.
Electrical Rating Chart — CSBFR Models
SPECIFICATIONS
Model
Compressor
Size Volts Hertz Watts Amps
Shipping
Weight
CSBFR-24-F 1/5 hp 120 60 300 3.8
96 lbs. (44 kg)
1/3 hp 220/230/240
50 1089/1190/1296 5.0/5.2/5.4
60 1129/1234/1344 5.1/5.4/5.6
CSBFR-24-I 1/5 hp 120 60 300 3.8
109 lbs. (49 kg)
1/3 hp 220/230/240
50 1089/1190/1296 5.0/5.2/5.4
60 1129/1234/1344 5.1/5.4/5.6
CSBFR-24-S 1/5 hp 120 60 300 3.8
124 lbs. (56 kg)
1/3 hp 220/230/240
50 1089/1190/1296 5.0/5.2/5.4
60 1129/1234/1344 5.1/5.4/5.6
CSBFR-36-F 1/5 hp 120 60 300 3.8
121 lbs. (55 kg)
1/3 hp 220/230/240
50 1089/1190/1296 5.0/5.2/5.4
60 1129/1234/1344 5.1/5.4/5.6
CSBFR-36-I 1/3 hp 120 60 450 5.9
137 lbs. (62 kg)
3/8 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
1/3 hp 60 1129/1234/1344 5.1/5.4/5.6
CSBFR-36-S 1/3 hp 120 60 450 5.9
163 lbs. (74 kg)3/8 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
1/3 hp 60 1129/1234/1344 5.1/5.4/5.6
CSBFR-48-F 1/3 hp 120 60 450 5.9
144 lbs. (65 kg)3/8 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
1/3 hp 60 1129/1234/1344 5.1/5.4/5.6
CSBFR-48-I 1/3 hp 120 60 450 5.9
173 lbs. (78 kg)3/8 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
1/3 hp 60 1129/1234/1344 5.1/5.4/5.6
CSBFR-48-S 5/8 hp 120 60 800 8.7
176 lbs. (80 kg)1/2 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
5/8 hp 60 1956/2138/2328 8.9/9.3/9.7
8
Form No. CSRM-0220
English
Electrical Rating Chart — CSSBFR Models
SPECIFICATIONS
The shaded areas contain electrical information for International models only.
NOTE: Shipping weight includes packaging and is estimated.
Model
Compressor
Size Volts Hertz Watts Amps
Shipping
Weight
CSSBFR-24-F 1/5 hp 120 60 300 3.8
101 lbs. (46 kg)
1/3 hp 220/230/240
50 1089/1190/1296 5.0/5.2/5.4
60 1129/1234/1344 5.1/5.4/5.6
CSSBFR-24-I 1/5 hp 120 60 300 3.8
115 lbs.(52 kg)
1/3 hp 220/230/240
50 1089/1190/1296 5.0/5.2/5.4
60 1129/1234/1344 5.1/5.4/5.6
CSSBFR-24-S 1/5 hp 120 60 300 3.8
131 lbs. (59 kg)
1/3 hp 220/230/240
50 1089/1190/1296 5.0/5.2/5.4
60 1129/1234/1344 5.1/5.4/5.6
CSSBFR-36-F 1/5 hp 120 60 300 3.8
130 lbs. (59 kg)
1/3 hp 220/230/240
50 1089/1190/1296 5.0/5.2/5.4
60 1129/1234/1344 5.1/5.4/5.6
CSSBFR-36-I 1/3 hp 120 60 450 5.9
146 lbs. (66 kg)3/8 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
1/3 hp 60 1129/1234/1344 5.1/5.4/5.6
CSSBFR-36-S 1/3 hp 120 60 450 5.9
173 lbs. (78 kg)3/8 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
1/3 hp 60 1129/1234/1344 5.1/5.4/5.6
CSSBFR-48-F 1/3 hp 120 60 450 5.9
153 lbs. (69 kg)3/8 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
1/3 hp 60 1129/1234/1344 5.1/5.4/5.6
CSSBFR-48-I 1/3 hp 120 60 450 5.9
187 lbs. (85 kg)
3/8 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
1/3 hp 60 1129/1234/1344 5.1/5.4/5.6
CSSBFR-48-S 5/8 hp 120 60 800 8.7
195 lbs. (89 kg)1/2 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
5/8 hp 60 1956/2138/2328 8.9/9.3/9.7
Form No. CSRM-0220
9
English
Electrical Rating Chart — CSUR Models
SPECIFICATIONS
The shaded areas contain electrical information for International models only.
NOTE: Shipping weight includes packaging and is estimated.
Model
Compressor
Size Volts Hertz Watts Amps
Shipping
Weight
CSUR-24-F 1/5 hp 120 60 300 3.8
101 lbs. (46 kg)
1/3 hp 220/230/240
50 1089/1190/1296 5.0/5.2/5.4
60 1129/1234/1344 5.1/5.4/5.6
CSUR-24-I 1/5 hp 120 60 300 3.8
115 lbs. (52 kg)
1/3 hp 220/230/240
50 1089/1190/1296 5.0/5.2/5.4
60 1129/1234/1344 5.1/5.4/5.6
CSUR-24-S 1/5 hp 120 60 300 3.8
131 lbs. (59 kg)
1/3 hp 220/230/240
50 1089/1190/1296 5.0/5.2/5.4
60 1129/1234/1344 5.1/5.4/5.6
CSUR-36-F 1/5 hp 120 60 300 3.8
130 lbs. (59 kg)
1/3 hp 220/230/240
50 1089/1190/1296 5.0/5.2/5.4
60 1129/1234/1344 5.1/5.4/5.6
CSUR-36-I 1/3 hp 120 60 450 5.9
146 lbs. (66 kg)3/8 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
1/3 hp 60 1129/1234/1344 5.1/5.4/5.6
CSUR-36-S 1/3 hp 120 60 450 5.9
173 lbs. (78 kg)3/8 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
1/3 hp 60 1129/1234/1344 5.1/5.4/5.6
CSUR-48-F 1/3 hp 120 60 450 5.9
153 lbs. (69 kg)3/8 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
1/3 hp 60 1129/1234/1344 5.1/5.4/5.6
CSUR-48-I 1/3 hp 120 60 450 5.9
187 lbs. (85 kg)
3/8 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
1/3 hp 60 1129/1234/1344 5.1/5.4/5.6
CSUR-48-S 5/8 hp 120 60 800 8.7
195 lbs. (89 kg)1/2 hp
220/230/240
50 826/904/984 3.8/3.9/4.1
5/8 hp 60 1956/2138/2328 8.9/9.3/9.7
10
Form No. CSRM-0220
English
Model
Width
(A)
Depth
(B)
Height
(C)
Cooled
Width (D)
Cooled
Depth (E)
CSBFR-24-F
CSBFX-24-F
25-1/2
(648 mm)
17
(432 mm)
2-1/8
(53 mm)
24
(610 mm)
15-1/2
(394 mm)
CSBFR-24-I
CSBFX-24-I
21
(533 mm)
19-1/2
(495 mm)
CSBFR-24-S
CSBFX-24-S
25-1/2
(648 mm)
24
(610 mm)
CSBFR-36-F
CSBFX-36-F
37-1/2
(953 mm)
17
(432 mm)
36
(914 mm)
15-1/2
(394 mm)
CSBFR-36-I
CSBFX-36-I
21
(533 mm)
19-1/2
(495 mm)
CSBFR-36-S
CSBFX-36-S
25-1/2
(648 mm)
24
(610 mm)
CSBFR-48-F
CSBFX-48-F
49-1/2
(1257 mm)
17
(432 mm)
48
(1219 mm)
15-1/2
(394 mm)
CSBFR-48-I
CSBFX-48-I
21
(533 mm)
19-1/2
(495 mm)
CSBFR-48-S
CSBFX-48-S
25-1/2
(648 mm)
24
(610 mm)
SPECIFICATIONS
Dimensions — CSBFR and CSBFX Models
E
D
A
C
B
Front View Side View
Top View
Form No. CSRM-0220
11
English
Model Width (A) Depth (B) Height (C) Cooled Width (D) Cooled Depth (E)
CSSBR-2418
CSSBX-2418
27
(686 mm)
21
(533 mm)
2-3/8
(60 mm)
24
(610 mm)
18
(457 mm)
CSSBR-3018
CSSBX-3018
33
(838 mm)
30
(762 mm)
CSSBR-3618
CSSBX-3618
39
(991 mm)
36
(914 mm)
CSSBR-4818
CSSBX-4818
51
(1295 mm)
48
(1219 mm)
CSSBFR-24-F
CSSBFX-24-F
27
(686 mm)
18-1/2
(470 mm)
2-3/8
(60 mm)
24
(610 mm)
15-1/2
(394 mm)
CSSBFR-24-I
CSSBFX-24-I
22-1/2
(572 mm)
19-1/2
(495 mm)
CSSBFR-24-S
CSSBFX-24-S
27
(686 mm)
24
(610 mm)
CSSBFR-36-F
CSSBFX-36-F
39
(991 mm)
18-1/2
(470 mm)
36
(914 mm)
15-1/2
(394 mm)
CSSBFR-36-I
CSSBFX-36-I
22-1/2
(572 mm)
19-1/2
(495 mm)
CSSBFR-36-S
CSSBFX-36-S
27
(686 mm)
24
(610 mm)
CSSBFR-48-F
CSSBFX-48-F
51
(1295 mm)
18-1/2
(470 mm)
48
(1219 mm)
15-1/2
(394 mm)
CSSBFR-48-I
CSSBFX-48-I
22-1/2
(572 mm)
19-1/2
(495 mm)
CSSBFR-48-S
CSSBFX-48-S
27
(686 mm)
24
(610 mm)
SPECIFICATIONS
Dimensions — CSSBR, CSSBFR, CSSBX, CSSBFX Models
Front View Side View
Top View
E
D
A
C
B
12
Form No. CSRM-0220
English
Model
Width
(A)
Depth
(B)
Height
(C)
Cooled
Width (D)
Cooled
Depth (E)
CSUR-24-F
CSUX-24-F
27-5/16
(694 mm)
18-13/16
(478 mm)
2-1/8
(54 mm)
24
(610 mm)
15-1/2
(394 mm)
CSUR-24-I
CSUX-24-I
22-13/16
(579 mm)
19-1/2
(495 mm)
CSUR-24-S
CSUX-24-S
27-5/16
(694 mm)
24
(610 mm)
CSUR-36-F
CSUX-36-F
39-5/16
(998 mm)
18-13/16
(478 mm)
36
(914 mm)
15-1/2
(394 mm)
CSUR-36-I
CSUX-36-I
22-13/16
(579 mm)
19-1/2
(495 mm)
CSUR-36-S
CSUX-36-S
27-5/16
(694 mm)
24
(610 mm)
CSUR-48-F
CSUX-48-F
51-5/16
(1303 mm)
18-13/16
(478 mm)
48
(1219 mm)
15-1/2
(394 mm)
CSUR-48-I
CSUX-48-I
22-13/16
(579 mm)
19-1/2
(495 mm)
CSUR-48-S
CSUX-48-S
27-5/16
(694 mm)
24
(610 mm)
SPECIFICATIONS
Dimensions — Condensing Unit
Top ViewFront View Side View
C
A
B
3X Ø 0.375
(10 mm)
D
E
Air Flow
Dimensions — CSUR and CSUX Models
NOTE: See dimension illustration for CSSBR and CSSBFR models on previous page for reference.
Models
Width
(A)
Depth
(B)
Height
(C)
Mounting Hole
Width (D)
Mounting Hole
Depth (E)
CSBFR, CSBR, CSUR, CSSBFR
-24-F, -24-I, -24-S, -36F
CSSBR-2418, -3018, -3618
14-5/8
(371 mm)
12-1/4
(312 mm)
11-3/8
(289 mm)
6-1/2
(165 mm)
9-1/2
(242 mm)
CSBFR, CSBR, CSUR, CSSBFR
-36-I, -36-S, -48-F, -48-I
CSSBR-4818
14-1/2
(369 mm)
12-1/4
(312 mm)
11-3/8
(289 mm)
6-1/2
(165 mm)
9-1/2
(242 mm)
120 V, 60 Hz
CSBFR-48-S, CSBR-48-S,
CSUR-48-S, CSSBFR-48-S
17-1/2
(444 mm)
16-3/8
(415 mm)
12-1/8
(306 mm)
9-1/4
(235 mm)
11-1/4
(286 mm)
220-230-240 V, 50 Hz
CSBFR-48-S, CSBR-48-S,
CSUR-48-S, CSSBFR-48-S
16-1/2
(420 mm)
13
(331 mm)
12-1/8
(306 mm)
9-1/4
(235 mm)
11-1/4
(286 mm)
Form No. CSRM-0220
13
English
INSTALLATION
General
Remote Built-In Cold Shelves are shipped from the factory as
components that require installation and connection. Use the
following information and procedures to prepare the unit and
the installation site.
NOTE: Make sure the installation location provides enough
room for the condensing unit and the remote mounted
control box.
WARNING
ELECTRIC SHOCK HAZARD:
• Units supplied without an electrical cord and plug
require a hardwired connection to on-site electrical
system. Connection must be properly grounded and
of correct voltage, size, and configuration for electrical
specifications of unit. Contact a qualified electrician to
determine and install proper electrical connection.
• Unit must be installed by qualified, trained installers.
Installation must conform to all local electrical and
plumbing codes. Installation by unqualified personnel
will void the unit warranty and may lead to electric
shock or burn, as well as damage to unit and/or its
surroundings. Check with local plumbing and electrical
inspectors for proper procedures and codes.
• Unit is not weatherproof. Locate unit indoors.
• Remote control box must be mounted on vertical wall
and installed in vertical position. Mounting remote
control box in horizontal position may result in
collection of liquids and lead to electric shock.
FIRE HAZARD: Install condensing unit with a minimum
of2″(51mm)ofspacebetweenallsidesofunitandany
combustible surfaces.
CAUTION
Locate the unit at the proper counter height in an area that is
convenient for use. The location should be level and strong
enough to support the weight of the unit and contents.
NOTICE
Transport and install unit in upright position only. Failure
to do so may result in damage to refrigeration system.
This unit is designed for use in environments where
ambient temperature is between 65°F (18°C) and 86°F
(30°C).
When shipped during cold weather months, store unit
for at least 10 hours in an environment where ambient
temperature is between 65°F (18°C) and 86°F (30°C) to
prevent compressor and/or refrigerant line damage. If unit
is turned on and there is excessive noise and vibration,
turn off immediately and allow additional warmup time.
Provide louvered or grill-style openings with a minimum
size of 12″ x 12″/144 square inches (31 x 31 cm/
961 square cm) in the cabinetry in front of and behind the
condensing unit for proper ventilation. Failure to provide
adequate air flow through the condensing unit may cause
unit failure and will void the unit warranty.
Do not recirculate exhaust air inside cabinet when multiple
condensing units are installed together. Intake air should
enter from outside of cabinet.
NOTICE
Do not locate unit in area with excessive air movement
around unit. Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods, air
conditioning ducts, and exterior doors).
Do not locate unit in an area subject to excessive
temperatures or grease from grills, fryers, etc. Excessive
temperatures could cause damage to the unit.
Damage to any countertop material caused by heat or cold
generated from Hatco equipment is not covered under
the Hatco warranty. Contact manufacturer of countertop
material for application information.
All cold shelves are shipped in a shipping frame for protection
and stability. Keep the unit in the shipping frame until the unit
and the installation site are completely prepared for the unit to
be installed.
Survey the installation site. Take into account the need for
louvered or grill-style openings in the cabinetry to provide
proper ventilation for the condensing unit as well as access to
the control panel. One of these ventilation openings must be in
front of the condensing coils with the other on the opposite side.
If multiple condensing units are installed in the same counter,
each unit should intake cool air and expel hot air.
1. Remove all external packaging from the unit.
NOTE: To prevent delay in obtaining warranty coverage, complete
online warranty registration. See the IMPORTANT
OWNER INFORMATION section for details.
2. Remove tape, protective packaging, and literature from all
surfaces of the unit.
Preparing the Installation Site
1. Prepare the appropriate opening and mounting bolt holes
in the countertop for the unit being installed.
• For top mounted CSBFR and CSBFX models, refer to
“Countertop Cutout Dimensions — Top Mounted Units,”
in this section.
• For bottom mounted CSSBR, CSSBFR, CSSBX, and
CSSBFX models, refer to “Countertop Cutout and
Mounting Bolt Dimensions — Bottom Mounted Units,”
in this section.
• For underside, surface mounted CSUR and CSUX
models, refer to “Mounting Bolt Dimensions—CSUR
and CSUX Models” in this section. Make sure the
countertop is a solid surface material with good heat
transfer characteristics, such as stainless steel, granite,
quartz, Corian
®
, etc... The thickness of the countertop
NOTE: The performance of each type of solid surface material
will vary dependant upon the material’s characteristics.
2. Cut and drill the appropriate holes in the vertical surface
where the control box will be installed. Refer to the
“Installing the Remote Control Box” procedure for cutout
dimensions.
• The installation depth required for the control box is
3. Make structural modifications or add bracing underneath
the countertop to ensure the countertop will support the
weight of the unit and its contents.
4. Install the unit. Refer to the appropriate procedure in this
section for the model being installed.
14
Form No. CSRM-0220
English
Model Width (A) Depth (B)
CSBFR-24-F
CSBFX-24-F
24-5/825
(625635 mm)
(409419 mm)
CSBFR-24-I
CSBFX-24-I
24-5/825
(625635 mm)
(511521 mm)
CSBFR-24-S
CSBFX-24-S
24-5/825
(625635 mm)
24-5/825
(625635 mm)
CSBFR-36-F
CSBFX-36-F
36-5/837
(930940 mm)
(409419 mm)
CSBFR-36-I
CSBFX-36-I
36-5/837
(930940 mm)
(511521 mm)
CSBFR-36-S
CSBFX-36-S
36-5/837
(930940 mm)
24-5/825
(625635 mm)
CSBFR-48-F
CSBFX-48-F
48-5/849
(12341245 mm)
(409419 mm)
CSBFR-48-I
CSBFX-48-I
48-5/849
(12341245 mm)
(511521 mm)
CSBFR-48-S
CSBFX-48-S
48-5/849
(12341245 mm)
24-5/825
(625635 mm)
INSTALLATION
B
A
Countertop Cutout Dimensions — Top Mounted Units
Installing a Top Mounted Unit (CSBFR and
CSBFX Models)
NOTICE
Use caution and avoid hitting condensing unit hoses/lines
when installing unit. Damage caused during installation is
not covered under warranty.
1. Apply a bead of National Sanitation Foundation (NSF)-
approved silicone sealant on the top edge of the countertop
cutout and the underside of the trim mounting ring. The
sealant must be rated for use at temperatures between
-10°F (-23°C) and 250°F (121°C).
2. Lift the cold shelf out of the shipping frame and carefully
lower it into the countertop cutout. This step requires two or
more people.
NOTE: If excessive condensation appears underneath the
countertop during operation, apply polyurethane-based
foam sealant in the gap between the underside of the
countertop and the shelf.
3. Install the control box in the desired location.
(1829 mm) of the shelf. Refer to the “Installing the
Remote Control Box” procedure in this section.
CAUTION
DO NOT tip unit/mounting surface after final installation.
Unit is free-floating and could fall out if tipped—for
permanent, horizontal installations only.
4. For CSBFR models, install the condensing unit in the
desired location. Refer to the SPECIFICATION section for
installation dimensions.
• Make sure the installation site provides a level, stable
surface for mounting the condensing unit.
• Make sure the installation site offers continuous air flow
ventilation to the condensing unit.
between all sides of the condensing unit and any
combustible surface.
5. Have qualified installers perform the “Connecting the
Components” procedure in this section.
6. Clean the cold surface thoroughly in preparation for initial
operation. Refer to the MAINTENANCE section for proper
cleaning procedures.
Countertop
Cutout
Installing a CSBFR Model Cold Shelf
Form No. CSRM-0220
15
English
Model
Cutout
Width (A)
Cutout
Depth (B)
Bolt Hole
Location (C)
Bolt Hole
Location (D)
Bolt Hole
Location (E)
Bolt Hole
Location (F)
CSSBR-2418
CSSBX-2418
24-3/8
(619 mm)
18-3/8
(467 mm)
(670 mm)
21
(533 mm)
(517 mm)
(380 mm)
CSSBR-3018
CSSBX-3018
30-3/8
(772 mm)
18-3/8
(467 mm)
(822 mm)
27
(685 mm)
(517 mm)
(380 mm)
CSSBR-3618
CSSBX-3618
36-3/8
(924 mm)
18-3/8
(467 mm)
(974 mm)
33
(837 mm)
(517 mm)
(380 mm)
CSSBR-4818
CSSBX-4818
48-3/8
(1229 mm)
18-3/8
(467 mm)
(1279 mm)
45
(1142 mm)
(517 mm)
(380 mm)
CSSBFR-24-F
CSSBFX-24-F
24-3/8
(619 mm)
15-7/8
(403 mm)
(670 mm)
21
(533 mm)
(454 mm)
(317 mm)
CSSBFR-24-I
CSSBFX-24-I
24-3/8
(619 mm)
19-7/8
(505 mm)
(670 mm)
21
(533 mm)
(555 mm)
(418 mm)
CSSBFR-24-S
CSSBFX-24-S
24-3/8
(619 mm)
24-3/8”
(619 mm)
(670 mm)
21
(533 mm)
(670 mm)
(533 mm)
CSSBFR-36-F
CSSBFX-36-F
36-3/8
(924 mm)
15-7/8
(403 mm)
(974 mm)
33
(837 mm)
(454 mm)
(317 mm)
CSSBFR-36-I
CSSBFX-36-I
36-3/8
(924 mm)
19-7/8
(505 mm)
(974 mm)
33
(837 mm)
(555 mm)
(418 mm)
CSSBFR-36-S
CSSBFX-36-S
36-3/8
(924 mm)
24-3/8”
(619 mm)
(974 mm)
33
(837 mm)
(670 mm)
(533 mm)
CSSBFR-48-F
CSSBFX-48-F
48-3/8
(1229 mm)
15-7/8
(403 mm)
(1279 mm)
45
(1142 mm)
(454 mm)
(317 mm)
CSSBFR-48-I
CSSBFX-48-I
48-3/8
(1229 mm)
19-7/8
(505 mm)
(1279 mm)
45
(1142 mm)
(555 mm)
(418 mm)
CSSBFR-48-S
CSSBFX-48-S
48-3/8
(1229 mm)
24-3/8
(619 mm)
(1279 mm)
45
(1142 mm)
(670 mm)
(533 mm)
INSTALLATION
BE F
A
C
D
R = 0.375" (9.5 mm) x 4
Mounting brackets shown for hole location reference. Holes must be pre-drilled
on underside of countertop where brackets will be mounted.
Countertop Cutout and Mounting Bolt Dimensions — Bottom Mounted Units
16
Form No. CSRM-0220
English
Installing a Bottom Mounted Unit (CSSBR,
CSSBFR, CSSBX, and CSSBFX Models)
NOTICE
Use caution and avoid hitting condensing unit hoses/lines
when installing unit. Damage caused during installation is
not covered under warranty.
Bottom
of unit.
Washer
Shipping
Screw
Mounting
Bracket
A
ssembly
1. Remove the mounting
bracket assembly from
each corner of the cold
shelf. To remove:
a. Remove the two shipping
screws and washers that
attach each mounting
bracket assembly to the
bottom of the unit.
b. Carefully lift the cold
shelf above the shipping
frame, and rotate it far enough to allow the unit to be set
back down on top of the frame (the mounting brackets
will stay on the frame or fall out the bottom). This step
requires two or more people, depending on the unit.
c. Remove the mounting bracket assemblies from the
frame, if necessary.
Shipping
Bracket
Shipping
Screw
2. On each mounting bracket
assembly, remove the
shipping screws and the
triangular shipping bracket
that was used to attach the
mounting bracket assembly
to the bottom of the cold
shelf, and discard.
3. Attach a mounting bracket
assembly to the underside
of the prepared countertop
at each corner of the cutout.
a. Align the u-shaped mounting holes on the mounting
bracket with the two pre-drilled mounting holes on the
underside of the countertop. The inside surface of the
mounting bracket should be vertically flush with the inner
surface of the countertop cutout.
b. Insert appropriate fasteners through the mounting
bracket and into appropriate anchoring devices in the
mounting holes on the underside of the countertop.
Tighten securely.
4. Install the included self-adhesive gasket around the inner,
vertical surface of the countertop cutout.
top surface of the countertop.
NOTE: If the accessory, self-adhesive gasket is not available,
provide a caulk backing around the inner, vertical
surface of the countertop cutout 1/4″ (6 mm) below
the top surface of the countertop. This will prevent the
silicone sealant applied later in this procedure from
falling through the gap between the countertop and the
cold shelf.
Countertop
Cutout
Accessory
Gasket
Inside surface of
mounting bracket
assembly flush with
inside of cutout.
Inside surface of
mounting bracket
assembly flush with
inside of cutout.
Lock Nut
Leveling Bolt
Installing a CSSBFR Model Cold Shelf
INSTALLATION
Form No. CSRM-0220
17
English
5. Carefully lower the condensing unit followed by the cold
shelf into the countertop cutout. This step requires two or
more people.
• The condensing unit must go into the cutout first and be
fastened to a level, stable surface within 6′ (1829 mm) of
the connections on the bottom of the cold shelf. Refer to
the SPECIFICATIONS section for installation dimensions.
• The cold shelf rests on top of the four leveling bolts,
which are part of the mounting bracket assembly
installed at each corner of the countertop cutout.
6. Adjust the leveling bolts underneath each corner of the unit
so that the shelf is flush or slightly below the countertop
surface.
7. Tighten the lock nut on each leveling bolt to secure the position.
8. Apply a bead of NSF-approved silicone sealant in the gap
above the countertop and the cold shelf. To apply a clean,
consistent sealant bead:
a. Make sure the shelf is centered in the countertop cutout.
b. Install masking tape on each side of the gap to define
the edge of the sealant.
c. Carefully apply sealant into the gap.
d. Quickly smooth the sealant surface.
e. Carefully remove the masking tape before the sealant dries.
NOTE: The silicone sealant must be rated for use at temperatures
between -10°F (-23°C) and 250°F (121°C).
9. Apply polyurethane-based foam sealant in the gap
underneath the countertop and the cold shelf.
Seal this gap with foam sealant
underneath the entire unit.
Foam Sealant Gap
CAUTION
DO NOT tip unit/mounting surface after final installation.
Unit is free-floating and could fall out if tipped—for
permanent, horizontal installations only.
10. Install the control box in the desired location.
• The control box can be installed remotely within
6′ (1829 mm) of the shelf. Refer to the “Installing the
Remote Control Box” procedure in this section.
11. For CSSBR and CSSBFR models, install the condensing
unit in the desired location. Refer to the SPECIFICATION
section for installation dimensions.
• Make sure the installation site offers continuous air flow
ventilation to the condensing unit.
between all sides of the condensing unit and any
combustible surface.
11. Have qualified installers perform the “Connecting the
Components” procedure in this section.
12. Clean the shelf surface thoroughly in preparation for initial
operation. Refer to the MAINTENANCE section for proper
cleaning procedures.
Installing an Under Mounted Unit
(CSUR and CSUX Models)
CSUR and CSUX models are surface mounted directly against
the underside of a solid surface countertop (no cutout is
required). Cooling transfers through the countertop to the top
side for a true, seamless installation.
Bottom
of unit.
Washer
Shipping
Screw
Mounting
Bracket
A
ssembly
1. Remove the mounting
bracket assembly from
each corner of the cold
shelf. To remove:
a. Remove the two shipping
screws and washers that
attach each mounting
bracket assembly to the
bottom of the unit.
b. Carefully lift the cold
shelf above the wooden shipping frame, and rotate it far
enough to allow the unit to be set back down on top of
the frame (the mounting brackets will stay on the frame
or fall out the bottom). Make sure the flexible tubes from
the condensing unit are not strained or damaged. This
step requires two or more people, depending on the unit.
c. Remove the mounting bracket assemblies from the
frame, if necessary.
Shipping
Bracket
Shipping
Screw
2. On each mounting bracket
assembly, remove the
shipping screws and the
triangular shipping bracket
that was used to attach the
mounting bracket assembly
to the bottom of the cold
shelf, and discard.
3. Attach three of the mounting
bracket assemblies to the
underside of the prepared
countertop at the pre-drilled locations. To attach each:
NOTE: See installation illustration on the following page.
a. Align the u-shaped mounting holes on the mounting
bracket with the two pre-drilled mounting holes on the
underside of the countertop. The inside surface of the
mounting bracket should be facing the unit.
b. Insert appropriate fasteners through the mounting
bracket and into appropriate anchoring devices in the
mounting holes on the underside of the countertop.
Tighten securely.
4. Apply a layer of thermal mastic to the top of the shelf using
continued...
INSTALLATION
18
Form No. CSRM-0220
English
INSTALLATION
5. Carefully lift the cold shelf up and into the three mounting
brackets on the underside of the countertop. This step
requires two or more people.
• The cold shelf rests on top of the leveling bolts, which
are part of the mounting bracket assembly installed at
each corner of the cold shelf.
• Slide one end of the cold shelf into the two brackets on
one end while rotating it into the single bracket on the
opposite end.
6. Attach the fourth mounting bracket assembly to the
underside of the countertop at the open corner of the cold
shelf.
7. Adjust the leveling bolts underneath each corner of the
unit so that the shelf is flush against the underside of the
countertop.
8. Tighten the lock nut on each leveling bolt to secure the
position.
9. Apply polyurethane-based foam sealant in the gap
between the countertop and the cold shelf.
Seal this gap with foam sealant
underneath the entire unit.
Foam Sealant Gap
10. Install the control box in the desired location.
• The control box can be installed remotely within 6′
(1829 mm) of the shelf. Refer to the “Installing the
Remote Control Box” procedure in this section.
11. For CSUR models, install the condensing unit in the
desired location. Refer to the SPECIFICATION section for
installation dimensions.
• Make sure the installation site provides a level, stable
surface for mounting the condensing unit.
• Make sure the installation site offers continuous air flow
ventilation to the condensing unit.
between all sides of the condensing unit and any
combustible surface.
12. Have qualified installers perform the “Connecting the
Components” procedure in this section.
Underside of
Countertop
Lock Nut
Leveling Bolt
Mounting
Bracket
Assembly
Installing a CSUR Model Cold Shelf
Form No. CSRM-0220
19
English
INSTALLATION
Model
Bolt Hole
Location (A)
Bolt Hole
Location (B)
Bolt Hole
Location (C)
Bolt Hole
Location (D)
CSUR-24-F
CSUX-24-F
(677 mm)
(541 mm)
(462 mm)
(325 mm)
CSUR-24-I
CSUX-24-I
(677 mm)
(541 mm)
(563 mm)
(426 mm)
CSUR-24-S
CSUX-24-S
(677 mm)
(541 mm)
(677 mm)
(541 mm)
CSUR-36-F
CSUX-36-F
(982 mm)
(845 mm)
(462 mm)
(325 mm)
CSUR-36-I
CSUX-36-I
(982 mm)
(845 mm)
(563 mm)
(426 mm)
CSUR-36-S
CSUX-36-S
(982 mm)
(845 mm)
(677 mm)
(541 mm)
CSUR-48-F
CSUX-48-F
(1287 mm)
(1150 mm)
(462 mm)
(325 mm)
CSUR-48-I
CSUX-48-I
(1287 mm)
(1150 mm)
(563 mm)
(426 mm)
CSUR-48-S
CSUX-48-S
(1287 mm)
(1150 mm)
(677 mm)
(541 mm)
C D
A
B
Mounting brackets shown for hole location reference. Holes must be pre-drilled
on underside of countertop where brackets will be mounted.
Unit Outline
Mounting Bolt Dimensions — CSUR and CSUX Models
20
Form No. CSRM-0220
English
Connecting the Components
Use the following procedure as a guideline for making
the connections between the components of the remote
refrigerated system. These connections must be made by
trained and qualified installers and must comply with all local
plumbing and electrical codes. Refer to the SPECIFICATIONS
section and the wiring diagram included with the unit for details
regarding the plumbing and electrical connections.
1. Connect the liquid and suction refrigerant lines between
the condensing unit, the TXV valve, and the refrigerated
evaporator coil. Refer to the appropriate illustration below
and the SPECIFICATIONS section for connection details.
NOTE: The maximum refrigerant line length between the
condensing unit and the evaporator coil is 50 feet (15 m).
NOTE: For refrigerant line connections, use a self-fluxing
brazing compound (example = Sil-Fos 5
®
) at a brazing
temperature range of 1300–1500°F (704–816°C).
Liquid
Connection
(1/4″ O.D. tube)
Condensing
Unit
TXV Valve
Suction Connection
(3/8″ O.D. tube)
TXV Bulb
Liquid Connection
(3/8″ O.D. tube)
Suction Connection
(3/8″ O.D. tube)
Suction Connection
(3/8″ O.D. tube)
Shelf
Fasten TXV bulb to
the suction side of
evaporator coil here.
Remote Refrigerant Connections
(CSUR, CSBFR, CSSBR, CSSBFR Models)
Shelf
Suction Connection
(3/8″ O.D. tube)
Suction Connection
(3/8″ O.D. tube)
TXV Valve
Solenoid
Valve
To Condensing
Unit
From
Condensing
Unit
Remote Refrigerant Connections
(CSUX, CSBFX, CSSBX, CSSBFX Models)
2. Have a qualified electrician make the appropriate electrical
connections to the control box. Refer to the wiring diagram
for details.
For CSUR, CSBFR, CSSBR, and CSSBFR Models:
a. Connect the on-site power supply through the power
input cord grip to the POWER IN terminal block.
b. Connect power from the POWER OUT terminal block,
through the power output cord grip, to the power input
on the condensing unit.
c. Connect the temperature probe wire from the refrigerated
shelf to the probe wire from the digital temperature
controller.
Power Input
Power Output
(to condensing unit on
“R” Models or solenoid
valve on “X” Models)
Temperature Probe
Wire Inlet
Terminal Blocks
Digital Temperature
Controller
Access Cover
Remote Refrigerant Connections
For CSUX, CSBFX, CSSBX, and CSSBFX Models:
a. Connect the on-site power supply through the power
input cord grip to the POWER IN terminal block.
b. Connect power from the POWER OUT terminal block,
through the power output cord grip, to the solenoid valve
on the refrigerated shelf.
c. Connect the temperature probe wire from the refrigerated
shelf to the probe wire from the digital temperature
controller.
INSTALLATION
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
Hatco CSUR, CSBFR, CSSBR, CSSBFR, CSUX, CSBFX, CSSBX, CSSBFX Series Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
Documents connexes
-
Hatco CSBF, CSU, CSSB, CSSBF Series Le manuel du propriétaire
-
-
-
-
-
-
-
-
-
