Fantech SHR6905R Guide d'installation

Light commercial models

Commercial Heat Recovery Ventilators

Installation Manual

Item #: 427685

Rev Date: 2018-02-02

SHR6904 • SHR6905R • SHR8004 • SHR11004 • SHR11005R • SHR14104

Your ventilation system should be installed in conformance with the appropriate provincial requirements or, in the absence of

such requirements, with the current edition of the National Building Code, and / or ASHRAE’s “Good Engineering Practices”.

Fantech reserves the right to modify, at any time and without notice, any or all of its products’ features, designs,

components and specifications to maintain their technological leadership position.

Please visit our website www.fantech.net for more detailed technical information.

United States

10048 Industrial Blvd., Lenexa, KS, 66215

Tel.: 800.747.1762 • Fax: 800.487.9915

Canada

50 Kanalflakt Way, Bouctouche, NB, E4S 3M5

Tel.: 800.565.3548 • Fax: 877.747.8116

2

Note Warning/

Important

note

Information Technical

information

Practical tip

PLEASE READ THIS MANUAL BEFORE INSTALLING UNIT

Before installation, careful consideration must be given to how this system will operate if connected to any other

piece of mechanical equipment, i.e. a forced air furnace or air handler, operating at a higher static pressure. After

installation, the compatibility of the two pieces of equipment must be confirmed by measuring the airflows of the

Heat / Energy Recovery Ventilator. It is always important to assess how the operation of any HRV/ERV may inter-

act with vented combustion equipment (i.e. Gas Furnaces, Oil Furnaces, Wood Stoves, etc.).

Never install a ventilator in a situation where its normal operation, lack of operation or partial failure may result

in the backdrafting or improper functioning of vented combustion equipment!!!

Products are designed and manufactured to provide reliable performance, but they are not guaranteed to be 100%

free of defects. Even reliable products will experience occasional failures, and this possibility should be recognized

by the user. If these products are used in a life support ventilation system where failure could result in loss or injury,

the user should provide adequate back-up ventilation, supplementary natural ventilation or failure alarm system, or

acknowledge willingness to accept the risk of such loss or injury.

Your ventilation system should be installed in accordance with the local building code that is in effect. In absence

of such requirements, it is recommenced to check with local authorities having jurisdiction in your area prior to

installing this product.

3

Understanding Fantech Product Numbers

SHR 6904

S = Side Ducting

H = Heat Recovery

R = Remote Control Option

690 = 690cfm @0.4 W.G

4 = Four Ports

5 = Five ports

R = Recirculation

Table of content

INSTALLATION

Location ...........................................................................4

Port Configuration .....................................................................5

Installing Drain Line ....................................................................5

Installing Duct Connections...............................................................6

AIRFLOW BALANCING ........................................................................7

Bypass Module (BPM)

Installing the BPM .....................................................................8

INSTALLATION EXAMPLES

Fully Dedicated Systems.................................................................9

Partially Dedicated Systems (direct connections) ...............................................9

Partially Dedicated Systems (indirect connections) .............................................10

Simplified Installation ..................................................................10

MODES OF OPERATION .......................................................................11

Speed Setting .......................................................................12

LOW VOLTAGE CONTROL SYSTEMS ..............................................................13

MAINTENANCE .............................................................................14

ELECTRICAL CONNECTIONS

SHR 6904 / SHR8004 / SHR11004 / SHR14104 .............................................15

SHR6905R / SHR11005R ..............................................................16

INSTALLATION VERIFICATION TEST

SHR 6904 / SHR8004 / SHR11004 / SHR14104 .............................................18

SHR6905R / SHR11005R ..............................................................19

PARTS LISTS

SHR6904 ..........................................................................41

SHR6905R.........................................................................42

SHR8004 ..........................................................................43

SHR11004 .........................................................................44

SHR11005R........................................................................45

SHR14104R........................................................................46

4

Installation

Location

The HRV must be located in a heated space where it will be possible to conveniently service the unit. Typically the HRV would be located in the

mechanical room, above a drop ceiling or an area close to the outside wall where the weatherhoods will be mounted. Attic installations are not normally

recommended due to extreme temperatures, and difficulty in performing required service & maintenance. If an attic is selected, special care should be

taken in ensuring the unit will perform as intended. Unit may need to be protected with insulated shelter, built on site.

Connecting appliances to the HRV It is not recommended, including:

• clothes dryer

• kitchen exhaust hoods

• combustion venting

• central vacuum system

These appliances may cause lint, dust or grease to collect in the HRV , damaging the unit.

Connecting any of these type of appliances to the HRV will invalidate your warranty

A

B

C

D

E

F

G

Model A B C D E F G

Kg lbs Kg lbs in. mm. Kg lbs Kg lbs Kg lbs in. mm.

SHR 6904/6905R 23.8 22.5 22.5 49.6 15.4 390 85 187 20 44 18.8 41.3 17.6 448

SHR 8004 20 44 17 37.5 15.9 404 71.5 158 19 41.9 16.5 36.4 11 282

SHR 11004/11005R 30.4 67 27 60 21.4 544 109 241 27.7 61 24.3 53.5 18 455

SHR 14104 29.2 64.4 24.5 54 19 483 116 255 30 66.2 34.7 76.5 10 254

5

Installing Drain Line

Through normal operation and including defrost mode, the HRV may produce some condensation. This water should flow into a nearby drain, or be taken

away by a condensate pump. The HRV and all condensate lines must be installed in a space where the temperature is maintained above the freezing

point. A “P” trap should be made in the drain line. This will prevent odors from being drawn back up into the unit.

Install the drain hose, making a “P” trap

Port configuration

The unit has access doors on the front and back. Also, the main control panel may be moved from front to back allowing for ducting layout.

SHR 6904, SHR 6905R, SHR 11004, SHR 11005R

COLD SIDE

WARM SIDE

SHR 8004, SHR 14104

WARM SIDE

WARM SIDE COLD SIDE

COLD SIDE

Factory Setting. Unit may be easily reversed

in eld.

Factory Setting. Unit may be easily reversed

in eld.

6

Installing ducts going to / from outside

Installing the ducting to the weatherhoods

Outside weatherhoods

The weatherhoods must have built-in "bird" screens with 1/4 inch (6.35 mm) minimum mesh to prevent birds and rodents from entering into the

ductwork. Do not use smaller mesh as it will be very susceptible to plugging up. The preferred location of the weatherhoods is:

• No less than 10 ft. (3 m) apart from each other.

• At least 18 inches (457.2 mm) above snow line or ground level.

• Supply hood must be kept away from sources of contaminants, such as automobile exhaust fumes, gas meters, garbage cans, containers,

cooling towers, tar roofs, etc.

• Avoid prevailing winds, whenever reasonably possible.

The outside perimeter of the weatherhood must be sealed to prevent leakage into the building.

The design and size of the weatherhoods or louvers chosen by the installer must allow for adequate free area. Water and snow penetration of the system

is minimized when the airflow does not exceed 1000 FPM (5.08 m/s) free area velocity.

Ducting from the weatherhoods –To and From the hrv

Galvanized sheet metal ducting with sufficient cross section with an integral single piece of insulated wrap with vapor barrier should be used to connect

the HRV to the weatherhoods. The R-value of the insulation should be adequate for condensation control. Insulated flex duct may be used in moderation,

if sized and installed properly. (Consult local codes)

All ducts should be sealed using a good bead of high quality caulking (preferably acoustical sealant) and a high quality aluminum foil tape, or other

approved duct sealant.

7

Exhaust air ducting

The stale air exhaust system is used to draw air from the points in the building where the worst air quality problems occur. ( See installation

examples in the manual.)

Installing ducts to / from inside

Direct connection to furnace/ air handler return duct

• Should you wish to hard duct the supply air directly into the cold air return of the HVAC systems, remember to check the airflow balance of the HRV

with the HVAC systems fan both “on”and “off” to determine that it does not imbalance the HRV more than 10%. Make sure you respect the minimum

distance from the supply air in of the HRV and the HVAC systems.

• It may be necessary to install a separate fresh air supply ductwork system if the heating is other than forced air.

When installing an HRV, the designer and installer should be aware of local codes that may require smoke detectors and/or firestats in the HVAC

or HRV ductwork.

Because an HRV is designed to bring fresh air into the building, structures may require supply voltage interrupt when smoke or flame sensors are

triggered, or when a central fire alarm system is activated.

To maximize airflow in the ductwork system, all ducts should be kept short and have as few bends or elbows as possible. Forty-five degree are

preferred to 90 elbows. Use “Y” tees instead of 90 elbows whenever possible.

All duct joints must be fastened with screws or duct sealant and wrapped with a quality duct tape to prevent leakage. Aluminum foil duct tape is

recommended.

Supply air ducting

In buildings without a forced air HVAC systems, fresh air should be supplied to all habitable areas. It should be supplied from high wall or ceiling

locations. Grilles that diffuse the air comfortably such as grille {MGE (metal) or CG (plastic)} grilles with "coanda effect" are recommended.

Optional inline duct heaters may be used to add heat if required.

A The duct’s airflow velocity

is generally measured

with a magnehelic gauge

and a pitot tube.

• To avoid airflow turbulence

and incorrect readings, the

airflow velocity should be

measured on steel ducting

a minimum of 3 duct

cross-sections from the

unit or elbow and before

any transition.

• The balancing procedure consists of measuring the exhaust air leaving the system and the supply air entering the system and ensuring that these

two are equal. A deviation of 10% or less is acceptable.

Airflow balancing

A*

Pitot tube and gauge

A professional air balancer should be contacted to commission the system properly. A skilled HVAC Tech may complete the balance

of air providing they possess the proper equipment. Call Fantech Technical support for assistance.

8

Installing BYPASS Module (BPM) - SHR6905R/SHR11005R

Kit content

• 1x BPM assembly

• 1x bracket "A"

• 2x bracket "B"

• 10x Screws

• 1x black extension wire*

• 1x red extentson wire*

* Only used when electrical box is

reversed

Bracket "A"

Bracket "B"

Figure 1

Bracket "B" Installed

Figure 2

Bracket "A Installed

Figure 3

BPM Tilted

Figure 4

BPM Fastening

Figure 5

Bracket "B" tightened

1. Loosely fasten both

brackets “B” to cabinet

using screws in the pilot

holes (Fig. 1). Don’t drive

the screw all the way;

leave about ¼” of thread

for the step 4.

2. Using the same screw

already on the unit,

assemble bracket “A” on

the cabinet (Fig. 2).

3. Install BPM by tilting it

(Fig. 3) so that the hole

on the mounting bracket

“A” lines up with the

pilot hole on top of the

BPM. Secure it with the

fastener and release

the BPM. The tilting

will enable the hole to

line up properly and will

compress the gasket

once released.

4. Assemble the remaining fasteners to secure the BPM

(Fig. 4). Continue to tighten the fasteners holding the

bracket “B” to cabinet in order to compress the gasket

between the BPM and the cabinet (Fig. 5).

Figure 6

Insert damper motor wires

through bushing

Figure 7

HCE Controller, showing "N.O."

terminal location and "C" terminal

location

5. Next route the damper motor wires through the plastic bushing (Fig.6) of

the electrical box and run the wires to the HCE controller on the terminal

marked “N.O.” in the eld marked “DAMPER” and on the terminal marked “C”

in the eld marked “24VAC”. (Fig. 7)

9

Installation examples

* Drawings are illustrations only and actual port locations and airflow directions may vary, consult unit spec sheets.

It is the responsibility of the installer to ensure all ductwork is sized and installed as designed to ensure the system will perform as intended.

The amount of air (CFM) that an HRV will deliver is directly related to the total external static pressure (E.S.P.) of the system. Static pressure

is a measure of resistance imposed on the blower by length of duct work/number of fittings used in duct work, duct heater etc.

Fully Dedicated System

• Stale air drawn from areas of contamination

• Fresh air supplied to main areas

• HRV airflow should be balanced

• External heating or cooling coil may be needed if air is not able to mix comfortably.

SUPPLY IN

EXHAUST OUT

HRV UNIT

SUPPLY DUCT

RETURN AIR DUCT

EXHAUST AIR TO HRV UNIT

AIR HANDLER UNIT

SUPPLY IN

BALANCING DAMPERS

SUPPLY IN

EXHAUST OUT

HRV UNIT

SUPPLY IN

BALANCING DAMPERS

Partially Dedicated System (Direct Connection)

• Stale air drawn from areas of contamination

• Fresh air supplied to return of air handler

• Air Handler blower may need to operate when call for ventilation

• HRV airflow should be balanced

10

Installation examples (Cont'd)

* Drawings are illustrations only and actual port locations and airflow directions may vary, consult unit spec sheets.

It is the responsibility of the installer to ensure all ductwork is sized and installed as designed to ensure the system will perform as intended.

The amount of air (CFM) that an HRV will deliver is directly related to the total external static pressure (E.S.P.) of the system. Static pressure

is a measure of resistance imposed on the blower by length of duct work/number of fittings used in duct work, duct heater etc.

SUPPLY IN

EXHAUST OUT

HRV UNIT

RETURN AIR DUCT

AIR HANDLER UNIT

SUPPLY IN

BALANCING DAMPERS

SUPPLY IN

EXHAUST OUT

HRV UNIT

SUPPLY DUCT

EXHAUST AIR TO HRV UNIT

12" BREATHER SPACE

CEILING RETURN AIR PLENUM

AIR HANDLER UNIT

SUPPLY IN

BALANCING DAMPERS

Simplified Installation

• Stale air drawn from return of air handler

• Fresh air supplied to return of air handler, further down

stream of HRV exhaust

• Air Handler blower must operate when HRV is providing

ventilation

• HRV airflow should be balanced

Partially Dedicated System (Indirect Connections)

• Stale air drawn from areas of contamination

• Fresh air supplied into ceiling return air plenum or grille

• HRV airflow should be balanced

11

1. Continuous / Ventilation Mode

In this mode of operation both fans are operating and exchanging air with the outside. The

heat recovery ventilator (HRV) constantly exchanges the air at the rate you select, either

at low or medium speed, and switches to high speed when activated by an optional remote

control. The "Low (reduced)" and "High (Normal)" fan speed selection will cause the unit

to operate in continuous exchange mode at a reduced exchange rate. Continuous mode

is recommended, since pollutants are slowly but constantly being generated in a building.

2. Intermittent / Standby Mode

The system is always on standby and operates at high speed when activated by an

optional remote control (required): "Standby" should be selected if the user wishes to

stop the unit from continuous exchange.

3a. Defrost (SHRXX04 Model) by evacuation

A preset defrost sequence is activated at an outdoor air temperature of 23ºF (-5ºC) and

lower.

During the defrost sequence, the supply blower shuts down & the exhaust blower continues

to ventilate for a preset time. The unit then returns to normal operation, and continues the

cycle.

3b. Defrost (SHRXX05R Model)

A preset defrost sequence is activated at an outdoor air temperature of -5ºC (23ºF)

and lower.

During the defrost sequence, the motorized damper in the bypass module (BPM)

temporarily blocks the incoming fresh air stream so that the warm air from the room can

circulate through the HRV. The exhaust blower shuts down and the supply blower

switches into high speed to maximize the effectiveness of the defrost strategy. During

this cycle, the unit will not create a negative pressure. Please note that these systems

are configured to defrost with the BPM devices installed on the fresh air from outside

port. Alternate configuration are available by contacting our technical support department.

Modes of operation

Stale Air

to Outside

Stale Air

from Inside

Recirculate Air from Inside

Supply air

to building

12

The HRV is shipped from the factory on low speed, intermittent operation can be obtained by toggling switch located on outside of cabinet.

The voltage selection for low (reduced) speed of the unit is done via jumpers shown in the illustration below. The default setting 75V.

Setting speed

Low: 75V

(Factory Default)

Low: 90V

Configurable speed control for low (reduced) speed

CAUTION MAKE SURE THE POWER TO THE UNIT IS DISCONNECTED BEFORE MAKING ANY CHANGES

13

AUXILIARY CONTROL – These controls can be paired

RTS2*

• 20- minute timer with LED light

• Boosts system to high speed with the touch of a button

• Up to 5 can be used in one system

• Use in bathroom, kitchen, laundry room

RTS5 • 20/40/60 minute timer with LED light

• Boosts system to high speed with the touch of a button

• Up to 5 can be used in one system

• Use in bathroom, kitchen, laundry room

MDEH1 • Rotary dial Dehumidistat

• Multiple units can be used

• We recommend setting the relative humidity above 80% during the summer

Low Voltage Control Systems

* Please see instruction manuals for individual controls for proper wiring and set up of control systems.

CENTRAL CONTROLS

These control options can only be used individually

CONTROLS FEATURES CONNECT TO

ECO-Touch® • Our most complete, yet easy to use control system

• Sleek design with backlight touchscreen LCD

• ECO mode selects the best operating mode and speed for the season,

minimizing energy use associated with ventilation

• Set preferred indoor relative humidity range and ventilation mode for day

and night conditions

• No battery to replace, all programmed settings are retained during power

outage

• Maintenance reminder indicator

• Error code messages reduce troubleshooting time

EDF7

• MODE button provides 3 modes of operations: Ventilation , Recircula-

tion and Standby

• User selected fan speed: Reduced, Medium, Normal and 20 minutes

per hour

• AUTO setting allows the homeowner to deactivate the dehumidistat

• When the humidity exceeds the desired setpoint, the ventilation sys-

tem operates at Normal speed.

• Once the desired humidity level is achieved, your ventilation system

resumes to its previous mode of operation

EDF1 / EDF1R • Press button once for continuous Reduced speed

• Press button twice and the unit will cycle 20 minutes ON/ 40 minutes

OFF and repeat

• EDF1 – Press button a third time and the system will run continuously

on HIGH speed

• EDF1R –Press button a third time and the system will run recirculation

on HIGH speed

1. Ensure that unit is not

plugged when connecting

the control

2. Recirculation mode is only

available with the “R” sufx

at the end of the model

number.

The wiring connectors

can be removed for

easier connection.

*Maintain polarity

between control

and HRV

(+ → + ; - → -)

W

+T

-T

D

+T

-T

14

Maintenance

The filters need to be checked and cleaned once a month or when they appear dirty.

filters

The motor - The motors are

factory balanced and lubricat-

ed for life. They require no

maintenance.

The unit - The inside of the

unit should be wiped clean

as needed.

Condensation Pan - Units with

drain hoses should have their

line and connection checked

regularly.

Outside hoods - The outside

hoods need to be checked

every season to make sure

there are no leaves or insects

blocking the airflow. Check

regularly that there are no

pollutants near the intake

hood. Make sure they are

clear of any snow accumula-

tion during the winter months.

Clean core on a average every 3-6 months or as needed.

a) Open access door & remove filters.

b) Carefully grip ends of core and pull evenly outward. Core may be snug, but will slide out of the

channel.

c) Wash the core in warm soapy water or light coil solution.

d) Install clean core

e) Install the clean filters

f) Replace access door

Core installation label on the outer end of the core.

To install the clean Core and Filters.

a) First mount the bottom flange of the core guide into the bottom channel approximately 1/4" (6mm)

b) Mount the left or right side flange of the core guide approximately 1/4" (6mm) followed by the other

side

c) Mount the top flange of the core guide into the top channel approximately 1/4" (6mm)

d) With all four corners in place and the core straight and even, push hard in the centre of the core

until the core stops on the back of the cabinet.

CAUTION MAKE SURE UNIT IS UNPLUGGED BEFORE ATTEMPTING ANY MAINTENANCE WORK

The following components should also be inspected regularly and well maintained.

Fixed plate

15

Wiring Diagram SHR6904/SHR8004/SHR11004/SHR14104

Supply

Voltage

ONONON

HIGH

SPEEDS

LOW

5

V

JP5 JP3

7

5

V

1

2

0

V

9

0

V

LOW

JP3JP5

HIGH

120V

90V

75V

55V

SPEEDS

16

Wiring Diagram SHR6905R/SHR11005R

Supply

Voltage

ONONON

HIGH

SPEEDS

LOW

5

V

JP5 JP3

7

5

V

1

2

0

V

9

0

V

LOW

JP3JP5

HIGH

120V

90V

75V

55V

SPEEDS

ON

17

W

R

G

C

Y

W

R G

Y

Standard Furnace Interlock Wiring

THERMOSTAT

TERMINALS

FURNACE

24-VOLT

TERMINAL BLOCK

FOUR

WIRE

TWO WIRE

heating only

TWO

WIRE

COOLING SYSTEM

W

R

G

C

Y

W

R G

Y

Alternate Furnace Interlock Wiring

THERMOSTAT

TERMINALS

FURNACE

24-VOLT

TERMINAL BLOCK

FOUR

WIRE

TWO WIRE

heating only

TWO

WIRE

COOLING SYSTEM

WIRE JOINT

WIRING DIAGRAM (CONT'D)

WIRING DIAGRAM TO

FURNACE

FOR A FURNACE

CONNECTION TO

A COOLING SYSTEM:

On some newer furnaces and older

thermostats, energizing the R and

G terminal at the furnace has the

effect of energizing the Y at the

thermostat and thereby turning on

the cooling system. If you identify this

type of thermostat, you must use the

“Alternate Furnace Interlock Wiring”

As per building codes and installation requirements for combustion appliances:

Air return ducts, or openings for air return, should not be placed in enclosed spaces containing combustion

appliances that are subject to spillage.

18

Installation Verification Test

SHR 6904, SHR 8004, SHR 11004, SHR 14104 Models

Without external control

1. Fan speed selector switch

• Set fan Speed selector switch to Standby.

2. Start-up

• Apply power to unit

• Unit should enter Exhaust only defrost mode for a 10 second duration and the following should occur:

Exhaust fan runs in HIGH (Normal) speed

Supply fan remains off

3. Standby

• Following the start-up unit should enter Standby mode. The following should occur:

Exhaust fan shuts off

Supply fan remains off

4. LOW (reduced) speed

• Set fans speed selector switch LOW (Reduced) speed. The following should occur.

Exhaust fan runs in LOW (Reduced) speed

Supply fan runs in LOW (Reduced) speed

5. HIGH (normal) speed

• Set fans speed selector switch HIGH (normal) speed. The following should occur.

Exhaust fan ramps up to HIGH (normal) speed

Supply fan ramps up to HIGH (normal) speed

6. Test completion

• Set fan speed selector switch to desired setting

• Installation Verification test is complete

With external control

1. Start-up

• Apply power to unit

• Unit should enter Exhaust only defrost mode for a 10 second duration and the following should occur:

Exhaust fan runs in HIGH (normal) speed

Supply fan remains off

2. External control

• Following start-up unit will respond to external control

• Consult user manual/instruction provided with external controller and ensure unit responds appropriately.

3. Test completion

• Installation Verification test is complete

19

SHR 6905R, SHR 11005R Models

Without External Control

1. Fan speed selector switch

• Set fan Speed selector switch to Standby.

2. Start-up

• Apply power to unit

• Unit should enter Recirculation mode for a 10 second duration and the following should occur:

Supply fan runs in HIGH (Normal) speed

Exhaust fan remains off

3. Standby

• Following the start-up unit should enter Standby mode. The following should occur:

Supply fan shuts off

Exhaust fan remains off

4. LOW (Reduce) speed

• Set fans speed selector switch LOW (Reduce) speed. The following should occur.

Supply fan runs in LOW (Reduce) speed

Exhaust fan runs in LOW (REDUCED) speed

5. HIGH (Normal) speed

• Set fans speed selector switch HIGH (Normal) speed. The following should occur.

Supply fan ramps up to HIGH (Normal)speed

Exhaust fan ramps up to HIGH (Normal) speed

6. Test completion

• Set fan speed selector switch to desired setting

• Installation Verification test is complete

With external control

1. Start-up

• Apply power to unit

• Unit should enter Recirculation mode for a 10 second duration and the following should occur:

Supply fan runs in HIGH (Normal) speed

Exhaust fan remains off

2. External control

• Following start-up unit will respond to external control

• Consult user manual/instruction provided with external controller and ensure unit responds appropriately.

3. Test completion

• Installation Verification test is complete

Installation Verification Test

20

Manuel d'installation

Limited Warranty

• The heat recovery aluminum core has a lifetime warranty.

• Fantech HRV's have a warranty that is limited to 3 years on all parts from the date of purchase, including parts replaced during this time period.

If there is no proof of purchase available, the date associated with the serial number will be used for the beginning of the warranty period.

• The motors found in all Fantech HRVs require no lubrication, and are factory balanced to prevent vibration and promote silent operation.

• The limited warranty covers normal use. It does not apply to any defects, malfunctions or failures as a result of improper installation, abuse,

mishandling, misapplication, fortuitous occurrence or any other circumstances outside Fantech’s control.

• Inappropriate installation or maintenance may result in the cancellation of the warranty.

• Any unauthorized work will result in the cancellation of the warranty.

• Fantech is not responsible for any incidental or consequential damages incurred in the use of the ventilation system.

• Fantech is not responsible for providing an authorized service centre near the purchaser or in the general area.

• Fantech reserves the right to supply refurbished parts as replacements.

• Transportation, removal and installation fees are the responsibility of the purchaser.

• The purchaser is responsible for adhering to all codes in effect in his area.

* This warranty is the exclusive and only warranty in effect relative to the ventilation system and all other warranties either expressed or implied are

invalid.

La page est en cours de chargement...