FEIN 7 112 40 Manuel utilisateur

FEIN Service

USA

FEIN Power Tools Inc.

1030 Alcon Street

Pittsburgh, PA 15220

Telephone: (412) 922-8886

Toll Free: 1-800-441-9878

www.feinus.com

Canada

FEIN Canadian Power Tool

Company

323 Traders Boulevard East

Mississauga, Ontario L4Z 2E5

Telephone.: (905) 8901390

Toll Free: 1-800-265-2581

FEIN Canadian Power Tool

Company

2810 De Miniac

St. Laurent, Quebec H4S 1K9

Telephone: (514) 331-7390

Toll Free: 1-800-789-8181

www.fein.com

Headquarter

C. & E. Fein GmbH

Hans-Fein-Straße 81

D-73529 Schwäbisch Gmünd-Bargau

www.fein.com

ASW14-6 PC 7 112 50

 ASW14-10 PC 7 112 51

 ASW14-14 PC 7 112 52

 ASW14-30 PC 7 112 53

ASW14-6 7 112 40

ASW14-10 7 112 42

ASW14-14 7 112 58

 ASM14-2 PC 7 112 61

 ASM14-6 PC 7 112 54

 ASM14-9 PC 7 112 55

 ASM14-12 PC 7 112 56

 ASM14-2 7 112 60

 ASM14-6 7 112 28

 ASM14-9 7 112 59

 ASM14-12 7 112 57

OBJ_DOKU-0000004035-002.fm Page 1 Tuesday, February 17, 2015 1:53 PM

2

Instruction Manual

Mode d’emploi

Instrucciones de uso

en

3

fr

20

es

38

OBJ_BUCH-0000000157-002.book Page 2 Tuesday, February 17, 2015 1:44 PM

3

en

For your safety.

Read all safety warnings and

all instructions. Failure to fol-

low the warnings and instructions may result

in electric shock, fire and/or serious injury.

Save all warnings and instructions for future-

reference.

Do not use this power tool before you

have thoroughly read and completely

understood this Instruction Manual, including

the figures, specifications, safety regulations

and the signs indicating DANGER, WARN-

ING and CAUTION.

Only carry out such operations with this

power tool as intended for by FEIN. Only use

application tools and accessories that have

been released by FEIN.

Please also observe the relevant national

industrial safety regulations.

Non-observance of the safety instructions in

the said documentation can lead to an electric

shock, burns and/or severe injuries.

This Instruction Manual should be kept for

later use and enclosed with the power tool,

should it be passed on or sold.

SAVE THESE INSTRUCTIONS.

The term “power tool” in the warnings refers

to your mains-operated (corded) power tool

or battery operated (cordless) power tool.

General safety rules.

1) Work area safety

a)Keep work area clean and well lit. Clut-

tered or dark areas invite accidents.

b)Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away

while operating a power tool. Distrac-

tion can cause you to lose control.

2) Electrical safety

a)Power tool plugs must match the outlet.

Never modify the plug in any way. Do not

use any adapter plugs with earthed

(grounded) power tools. Unmodified

plugs and matching outlets will reduce

risk of electric shock.

b)Avoid body contact with earthed or

grounded surfaces such as pipes, radia-

tors, ranges and refrigerators. There is

an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power

tool will increase the risk of electric

shock.

d)Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase

the risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for out-

door use. Use of a cord suitable for out-

door use reduces the risk of electric

shock.

f) If operating a power tool in a damp loca-

tion is unavoidable, use a ground fault

circuit interrupter (GFCI) protected sup-

ply. Use of an GFCI reduces the risk of

electric shock.

3) Personal safety

a)Stay alert, watch what you are doing

and use common sense when operating

a power tool. Do not use a power tool

while you are tired or under the influ-

ence of drugs, alcohol or medication. A

moment of inattention while operating

power tools may result in serious per-

sonal injury.

b)Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing pro-

tection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or bat-

tery pack, picking up or carrying the

tool. Carrying power tools with your

finger on the switch or energising

power tools that have the switch on

invites accidents.

WARNING

OBJ_BUCH-0000000157-002.book Page 3 Tuesday, February 17, 2015 1:44 PM

4

en

d)Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotat-

ing part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose cloth-

ing or jewelery. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewelry or long hair can

be caught in moving parts.

g)If devices are provided for the connec-

tion of dust extraction and collection

facilities, ensure these are connected

and properly used. Use of dust collec-

tion can reduce dust-related hazards.

4) Power tool use and care

a)Do not force the power tool. Use the cor-

rect power tool for your application. The

correct power tool will do the job bet-

ter and safer at the rate for which it was

designed.

b)Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the

switch is dangerous and must be

repaired.

c) Disconnect the plug from the power

source and/or the battery pack from the

power tool before making any adjust-

ments, changing accessories, or storing

power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d)Store idle power tools out of the reach of

children and do not allow persons unfa-

miliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands

of untrained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts,

breakage of parts and any other condi-

tion that may affect the power tool’s

operation. If damaged, have the power

tool repaired before use. Many accidents

are caused by poorly maintained power

tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to

bind and are easier to control.

g)Use the power tool, accessories and tool

bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to be

performed. Use of the power tool for

operations different from those

intended could result in a hazardous sit-

uation.

5) Battery tool use and care

a)Recharge only with the charger speci-

fied by the manufacturer. A charger that

is suitable for one type of battery pack

may create a risk of fire when used with

another battery pack.

b)Use power tools only with specifically

designated battery packs. Use of any

other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep it

away from other metal objects, like

paper clips, coins, keys, nails, screws or

other small metal objects, that can

make a connection from one terminal to

another. Shorting the battery terminals

together may cause burns or a fire.

d)Under abusive conditions, liquid may be

ejected from the battery; avoid contact.

If contact accidentally occurs, flush

with water. If liquid contacts eyes, addi-

tionally seek medical help. Liquid

ejected from the battery may cause irri-

tation or burns.

6) Service

a)Have your power tool serviced by a qual-

ified repair person using only identical

replacement parts. This will ensure that

the safety of the power tool is main-

tained.

OBJ_BUCH-0000000157-002.book Page 4 Tuesday, February 17, 2015 1:44 PM

5

en

Special safety instructions.

Hold power tool by insulated gripping sur-

faces, when performing an operation where

the fastener may contact hidden wiring. Fas-

teners contacting a “live” wire may make

exposed metal parts of the power tool “live”

and could give the operator an electric shock.

Beware of any concealed electric cables, gas

or water conduits. Check the working area

before commencing work, e. g. with a metal

detector.

Secure the work piece firmly. A work piece

that is gripped tightly in a clamping device or

vice, is more secure than if held by hand.

Hold the power tool firmly. High reaction

torque can briefly occur.

Do not machine any material containing

asbestos. Asbestos is cancerogenic.

Do not rivet or screw any name-plates or

signs onto the power tool. If the insulation is

damaged, protection against an electric shock

will be ineffective. Adhesive labels are recom-

mended.

Do not use accessories which are not specifi-

cally designed and recommended by the

power tool manufacturer. Safe operation is

not ensured merely because an accessory fits

your power tool.

Do not direct the power tool against yourself,

other persons or animals. Danger of injury

from sharp or hot application tools.

Never look or stare into the light of the power

tool's lamp from a short distance. Never point

the light of the lamp into the eyes of other

persons in close vicinity. The radiation pro-

duced by the lamp can be harmful for the eye.

Clean the ventilation openings on the power

tool at regular intervals using non-metal

tools. The blower of the motor draws dust

into the housing. An excessive accumulation

of metallic dust can cause an electrical hazard.

Use and handling of the battery

(battery pack)

To avoid hazardous situations such as burns,

fire, explosion, skin injuries, and other inju-

ries when handling the battery, observe the

following instructions:

Batteries must not be disassembled, opened

or reduced in size. Do not subject batteries to

mechanical impact or shock. Hazardous

vapours and fluid can escape in case of dam-

age and improper use of the battery. The

vapours can irritate the respiratory system.

Liquid ejected from the battery may cause

skin irritations or burns.

When battery fluid from a damaged battery

has come into contact with objects close by,

check the respective components, clean them

or replace them as required.

Keep the battery away from heat and fire. Do

not store the battery in direct sunlight.

Do not remove the battery from its original

packaging until it is going to be used.

Before any work on the machine itself,

remove the battery from the power tool. If the

power tool accidentally starts, there is danger

of injury.

Remove the battery only when the power tool

is switched off.

Keep the battery away from children.

Keep the battery clean and protect it against

moisture and water. Clean contaminated bat-

tery terminals and power tool connections

with a dry, clean cloth.

Use only intact original FEIN batteries that are

intended for your power tool. When working

with and charging incorrect, damaged,

repaired or reconditioned batteries, imita-

tions or other brands, there is danger of fire

and/or explosion.

Follow the safety warnings in the operating

instructions of the battery charger.

Hand/arm vibrations.

While working with this power

tool, hand/arm vibrations

occur. These can lead to health impairments.

The vibration emission value

during actual use of the power

tool can differ from the declared value

depending on the ways in which the tool is

used.

WARNING

OBJ_BUCH-0000000157-002.book Page 5 Tuesday, February 17, 2015 1:44 PM

6

en

It is necessary to identify safety

measures to protect the oper-

ator that are based on an estimation of expo-

sure in the actual conditions of use.

The vibration emission level given in this

information sheet has been measured in

accordance with a standardized test given in

EN 60745 and may be used to compare one

tool with another. It may be used for a pre-

liminary assessment of exposure.

The declared vibration emission level repre-

sents the main applications of the tool. How-

ever, if the tool is used for different

applications with different accessories or

poorly maintained, the vibration emission

may differ. This may significantly increase the

exposure level over the total working period.

An estimation of the level of exposure to

vibration should also take into account the

times when the tool is switched off or when

it is running but not actually doing the job.

This may significantly reduce the exposure

level over the total working period.

Identify additional safety measures to protect

the operator from the effects of vibration

such as: maintain the tool and the accessories,

keep the hands warm, organization of work

patterns.

Emission values for sound and vibration (Two-figure – specifications as per ISO 4871)

WARNING

Sound emission ASM

14-2

PC

ASM

14-6

PC

ASM

14-9

PC

ASM

14-12

PC

ASM

14-2

ASM

14-6

ASM

14-9

ASM

14-12

A-weighted emission pres-

sure power level measured

at the workplace

L

pA

(re 20 μPa), in decibels < 67 < 67 < 67 < 67 < 67 < 67 < 67 < 67

Measuring uncertainty

K

pA

,

in decibels 33333333

Measured A-weighted

sound power level

L

wA

(re 1 pW), in decibels < 78 < 78 < 78 < 78 < 78 < 78 < 78 < 78

Measuring uncertainty

K

wA

,

in decibels 33333333

C-weighted peak sound

pressure level measured at

the workplace

L

pCpeak

, in

decibels < 81 < 81 < 81 < 81 < 81 < 81 < 81 < 81

Measuring uncertainty

K

pCpeak

, in decibels 33333333

Vibrations

Weighted acceleration, in

– m/s

2

– ft/s

2

0.3

0.9

0.2

0.7

0.3

0.9

0.3

0.9

0.3

0.9

0.2

0.7

0.3

0.9

0.5

1.5

Measuring uncertainty

K

, in

– m/s

2

– ft/s

2

1.5

4.9

1.5

4.9

1.5

4.9

1.5

4.9

1.5

4.9

1.5

4.9

1.5

4.9

1.5

4.9

REMARK: The sum of the measured emission value and respective measuring inaccuracy rep-

resents the upper limit of the values that can occur during measuring.

Wear hearing protection!

Measured values determined in accordance with the corresponding product standard.

OBJ_BUCH-0000000157-002.book Page 6 Tuesday, February 17, 2015 1:44 PM

7

en

Intended use of the power tool:

Hand-held screwdriver for screwing in and

unscrewing screws and nuts in weather-pro-

tected environments without water supply

using the application tools and accessories

recommended by FEIN.

Sound emission ASW

14-6 PC

ASW

14-10 PC

ASW

14-14 PC

ASW

14-30 PC

ASW

14-6

ASW

14-10

ASW

14-14

A-weighted emission pres-

sure power level measured

at the workplace

L

pA

(re 20 μPa), in decibels < 71 < 71 < 71 < 71 < 71 < 71 < 71

Measuring uncertainty

K

pA

,

in decibels 3 3 3 3 3 3 3

Measured A-weighted

sound power level

L

wA

(re 1 pW), in decibels < 82 < 82 < 82 < 82 < 82 < 82 < 82

Measuring uncertainty

K

wA

, in decibels 3 3 3 3 3 3 3

C-weighted peak sound

pressure level measured at

the workplace

L

pCpeak

, in

decibels < 86 < 86 < 86 < 86 < 86 < 86 < 86

Measuring uncertainty

K

pCpeak

, in decibels 3 3 3 3 3 3 3

Vibrations

Weighted acceleration, in

– m/s

2

– ft/s

2

0.4

1.4

0.4

1.4

0.6

2.1

0.5

1.5

0.4

1.4

0.4

1.4

0.6

2.1

Measuring uncertainty

K

, in

– m/s

2

– ft/s

2

1.5

4.9

1.5

4.9

1.5

4.9

1.5

4.9

1.5

4.9

1.5

4.9

1.5

4.9

REMARK: The sum of the measured emission value and respective measuring inaccuracy rep-

resents the upper limit of the values that can occur during measuring.

Wear hearing protection!

Measured values determined in accordance with the corresponding product standard.

OBJ_BUCH-0000000157-002.book Page 7 Tuesday, February 17, 2015 1:44 PM

8

en

Symbols.

Symbol, character Explanation

Do not touch the rotating parts of the power tool.

Make sure to read the enclosed documents such as the Instruction Man-

ual and the General Safety Instructions.

Observe the instructions in the text or graphic opposite!

Before commencing this working step, remove the battery from the

power tool. Otherwise there may be danger of injury caused by unin-

tentional starting of the power tool.

Use eye protection during operation.

Use ear protection during operation.

Use protective gloves during operation.

Do not charge damaged batteries.

Keep the battery away from fire. Protect the battery against heat, e. g.

against continuous intense sunlight.

Observe the notes in the text aside!

This symbol confirms the certification of this product for the USA and

Canada.

Confirms the conformity of the power tool with the guidelines of the

European Community.

This sign warns of a directly imminent, dangerous situation. A false reac-

tion can cause a severe or fatal injury.

This sign indicates a possible dangerous situation that could cause severe

or fatal injury.

This sign warns of a possible dangerous situation that could cause injury.

Recycling code: identifies recyclable materials

Worn out power tools and other electrotechnical and electrical prod-

ucts should be sorted separately for environmentally-friendly recycling.

Caution: Do not look or stare into the switched-on lamp!

Reduce torque

Increase torque

DANGER

WARNING

CAUTION

OBJ_BUCH-0000000157-002.book Page 8 Tuesday, February 17, 2015 1:44 PM

9

en

Character Unit of measurement,

national

Explanation

n

0

rpm; /min; min

-1

; r/min No-load speed

n

Reset

rpm; /min; min

-1

; r/min Speed (factory-set at delivery)

(ASM..PC/ASW..PC only)

M...

Nm, in/lbs Torque

P

W Electrical power

°Angle width

U V Electric voltage

f Hz Frequency

I

A Electric current intensity

m

kg, lbs Mass

l ft, in Length, width, height, depth, diameter or thread

Ø ft, in Diameter of a round part

m, s, kg, A, mm, V, W,

Hz, N, °C, dB, min, m/s

2

Basic and derived units of measurement from the

international system of units SI.

OBJ_BUCH-0000000157-002.book Page 9 Tuesday, February 17, 2015 1:44 PM

10

en

Technical description and specifications.

Before mounting or replacing application tools or accessories, remove the bat-

tery. This preventive safety measure rules out the danger of injuries through

accidental starting of the power tool.

All accessories described or shown in this instruction manual will not be included with your-

power tool.

WARNING

On/Off switch

Tool holder

Cover

Light

Battery-Unlocking button

Battery

Gripping

surface

LED indication on battery

ASM 14-2 PC/ASM 14-6 PC/ASM14-9 PC/ASM 14-12 PC/

ASM 14-2/ASM 14-6/ASM 14-9/ASM 14-12

LED indication

Fig. 1

Ein-/Ausschalter

Tool holder

Light

Battery-Unlocking button

Battery

LED indication on battery

ASW 14-6 PC/ASW 14-10 PC/ASW 14-14 PC/

ASW 14-6/ASW 14-10/ASW 14-14

Gripping surface

Cover

Fig. 2

LED indication

On/Off switch

OBJ_BUCH-0000000157-002.book Page 10 Tuesday, February 17, 2015 1:44 PM

11

en

On/Off switch

LED indication

Tool holder

Light

Battery-Unlocking button

Battery

LED indication on battery

ASW 14-30 PC

Gripping surface

Cover

Fig. 3

Type ASM

14-2 PC

ASM

14-6 PC

ASM

14-9 PC

ASM

14-12 PC

ASM

14-2

ASM

14-6

ASM

14-9

ASM

14-12

Order number 7 112 61 7 112 54 7 112 55 7 112 56 7 112 60 7 112 28 7 112 59 7 112 57

Rated voltage 14.4 V 14.4 V 14.4 V 14.4 V 14.4 V 14.4 V 14.4 V 14.4 V

Rated speed 50 –

750/min

50 –

1000/min

50 –

750/min

50 –

750/min 350/min 600/min 600/min 500/min

Speed (factory-set at

delivery) 350/min 500/min 500/min 400/min – – – –

Torque 2 Nm

17.7 in/lbs

6 Nm

53.1 in/lbs

9 Nm

79.7 in/lbs

12 Nm

106.2

in/lbs

2 Nm

17.7 in/lbs

6 Nm

53.1 in/lbs

9 Nm

79.7 in/lbs

12 Nm

106.2

in/lbs

Weight according to

EPTA-Procedure

01/2003

2.86 lbs

(1.3 kg)

2.86 lbs

(1.3 kg)

2.86 lbs

(1.3 kg)

2.86 lbs

(1.3 kg)

2.86 lbs

(1.3 kg)

2.86 lbs

(1.3 kg)

2.86 lbs

(1.3 kg)

2.86 lbs

(1.3 kg)

Hexagon socket tool

holder 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4"

Type ASW

14-6 PC

ASW

14-10 PC

ASW

14-14 PC

ASW

14-30 PC

ASW

14-6

ASW

14-10

ASW

14-14

Order number 7 112 50 7 112 51 7 112 52 7 112 53 7 112 40 7 112 42 7 112 58

Rated voltage 14.4 V 14.4 V 14.4 V 14.4 V 14.4 V 14.4 V 14.4 V

Rated speed 50 –

700/min

50 –

700/min

50 –

530/min

20 –

260/min 650/min 500/min 400/min

Speed (factory-set at

delivery) 350/min 400/min 300/min 150/min – – –

Torque 6 Nm

53.1 in/lbs

10 Nm

88.5 in/lbs

14 Nm

123.9 in/lbs

30 Nm

265.5 in/lbs

6 Nm

53.1 in/lbs

10 Nm

88.5 in/lbs

14 Nm

123.9 in/lbs

Weight according to

EPTA-Procedure

01/2003

3.08 lbs

(1.4 kg)

3.08 lbs

(1.4 kg)

3.08 lbs

(1.4 kg)

4.40 lbs

(2.0 kg)

3.08 lbs

(1.4 kg)

3.08 lbs

(1.4 kg)

3.08 lbs

(1.4 kg)

Hexagon socket tool

holder –––3/8"–––

OBJ_BUCH-0000000157-002.book Page 11 Tuesday, February 17, 2015 1:44 PM

12

en

Assembly instructions.

Before mounting or replacing application tools or accessories, remove the bat-

tery. This preventive safety measure rules out the danger of injuries through

accidental starting of the power tool.

Removing and charging the battery

(figure 4).

Prior to the first charging procedure,

read the operating instructions of the

battery charger.

Charge the battery completely before

putting into operation for the first time.

Release the battery by pressing the battery

unlocking button and pull the battery out of

the handle. Do not exert any force when

doing this.

Connect the battery charger to a socket out-

let, slide the battery onto the battery charger

and charge the battery. After the charging

process is over, insert the battery into the

power tool and pull the plug of the battery

charger out of the socket outlet.

A new battery does not reach its full capacity

until after several charging and discharging

procedures.

Mounting the angle head

(ASW 14-6 PC, ASW 14-10 PC,

ASW 14-14 PC , ASW 14-6, ASW 14-10,

ASW 14-14) (figure 5).

Turn the clamping sleeve clockwise almost to

the stop and insert the connector.

Mount the angle head onto the flange and

turn the angle head until the shaft engages

into the connector. After the angle head faces

against the flange, align the angle head and

tighten it sufficiently with the clamping sleeve.

WARNING

Fig. 4

Battery-Unlocking

button

Battery

Fig. 5

1.

2.

Connector

Angle head

OBJ_BUCH-0000000157-002.book Page 12 Tuesday, February 17, 2015 1:44 PM

13

en

Aligning the angle head

(ASW 14-6 PC, ASW 14-10 PC,

ASW 14-14 PC , ASW 14-6, ASW 14-10,

ASW 14-14) (figure 6).

Loosen the clamping sleeve and turn the angle

head to the desired working position.

Retighten the clamping sleeve.

Aligning the angle head

(ASW 14-30 PC) (figure 7).

Counter-hold the angle head and loosen the

lock nut using two open-end wrenches; turn

the angle head to the desired working posi-

tion, hold it in place and tighten the lock nut

again using the open-end wrenches.

Changing the tool (figure 8).

Push the sleeve of the tool holder toward the

front.

Insert the application tool and release the

sleeve.

Fig. 6

2.

3.

1.

Angle head

Fig. 7

Angle head

4.

1.

2.

3.

Fig. 8

Application tool

Sleeve

OBJ_BUCH-0000000157-002.book Page 13 Tuesday, February 17, 2015 1:44 PM

14

en

Adjustments.

Before mounting or replacing application tools or accessories, remove the bat-

tery. This preventive safety measure rules out the danger of injuries through

accidental starting of the power tool.

Setting the torque (figure 9).

Open the cover using a screwdriver.

Turn the tool holder until the hole can be

seen under the cover.

Adjust the desired torque with the torque

setting tool.

Turn in the direction of the “+” to increase

the torque.

Turn in the direction of the “–” to reduce the

torque.

Shut the cover again.

WARNING

Fig. 9

1.

3.

4.

5.

2.

OBJ_BUCH-0000000157-002.book Page 14 Tuesday, February 17, 2015 1:44 PM

15

en

Selecting the rotation direction

(figure 10).

Adjust the rotation selector switch only when

the machine is at a complete stop.

Set the rotation selector switch to right or left

rotation as required.

A short beep sounds when actuating the rota-

tion selector.

In left-hand running mode, both LED indica-

tors (red/green) flash.

The selected rotation direction is maintained

until actuating the rotation selector again.

Changing the battery does not effect a change

of the rotation direction.

Fig. 10

Rotational direction switch

ASM 14-2 PC/ASM 14-6 PC/

ASM14-9 PC/ASM 14-12 PC/

ASM 14-2/ASM 14-6/ASM 14-9/ASM 14-12

ASW 14-6 PC/ASW 14-10 PC/ASW 14-14 PC/

ASW 14-6/ASW 14-10/ASW 14-14/ASW 14-30 PC

OBJ_BUCH-0000000157-002.book Page 15 Tuesday, February 17, 2015 1:44 PM

16

en

Working instructions.

Before mounting or replacing application tools or accessories, remove the bat-

tery. This preventive safety measure rules out the danger of injuries through

accidental starting of the power tool.

Do not use accessories not specifically intended and recommended for this power tool by FEIN.

The use of non-original FEIN accessories can lead to overheating of the power tool and destroy

it.

For each job, use only the FEIN application tool released and intended for the

respective application.

Switching on and off (figure 11).

Always hold the power tool

firmly. Otherwise, you could

lose control over the power tool.

The power tool is equipped with a soft-start-

ing feature.

If the motor switches off after a proper

screwdriving operation, restarting is not pos-

sible until after 0.8 seconds. This prevents

accidental retightening of already tightened

screws.

Switching on:

When pressing the On/Off switch halfway in,

the light goes on.

When pressing the On/Off switch completely

in, the light and the power tool are on.

Switching off:

To switch off the power tool, release the

On/Off switch.

WARNING

CAUTION

Fig. 11

ASM 14-2 PC/ASM 14-6 PC/

ASM14-9 PC/ASM 14-12 PC/

ASM 14-2/ASM 14-6/ASM 14-9/ASM 14-12

ASW 14-6 PC/ASW 14-10 PC/ASW 14-14 PC/

ASW 14-6/ASW 14-10/ASW 14-14/ASW 14-30 PC

2.

1.

OBJ_BUCH-0000000157-002.book Page 16 Tuesday, February 17, 2015 1:44 PM

17

en

Handling the battery.

Operate and charge the battery only within

the battery operating-temperature range of

0°C – 45°C (32°F – 113°F). At the begin-

ning of the charging procedure, the battery

temperature must be within the battery oper-

ating-temperature range.

Battery charge-control indicator

(figure 12).

Press the button to activate the LED indica-

tion.

The real percentage of the battery charge

condition is only indicated when the power

tool motor is stopped.

The electronics automatically switch off the

motor prior to the battery being deep dis-

charged.

Meaning of the LED indicators and the

beeps of the power tool

Green LED indicator lit.

The screwdriving operation has been carried

out properly. The preset torque has been

reached.

Red LED indicator lit and a short beep.

The screwdriving operation has not been car-

ried out properly. The preset torque has not

been reached. The screwdriving operation

must be carried out once more.

Red LED indicator lit and no beep.

The rotational direction switch or the On/Off

switch were pressed while sliding on the bat-

tery. Release the switches again. When the

red LED indicator goes out, the machine is

ready for operation again.

When the red LED indicator does not go out,

either a memory error is given or the On/Off

switch is defective. The electronic system is

defective and must be replaced by the after-

sales service.

LED

indicator

Meaning Activity

1–4

green LED

Percent-

age of

charge

condition

Operation

Continu-

ous red

light

Battery is

almost

empty

Charge battery

Red flash-

ing light

Battery is

not ready

for opera-

tion

Bring the battery

into the battery

operating-temper-

ature range, then

charge

Fig. 12

100 %

75 %

50 %

25 %

0 %

OBJ_BUCH-0000000157-002.book Page 17 Tuesday, February 17, 2015 1:44 PM

18

en

Red LED indicator flashes (1 time per second).

The battery is discharged (empty) and must

be replaced. The machine is blocked and will

not be ready for operation until after being

voltage-free for approx. 10 seconds.

Red LED indicator flashes (2 times per

second).

The machine is overheated, the over-temper-

ature protection has responded. After cooling

down, the machine is ready for operation

again. If the over-temperature protection

responds several times briefly after each

other, have the power tool checked by the

after-sales service.

Brief lighting up of both LEDs.

The cordless screwdriver switches to the

Energy Saving Mode.

Parameter assignment

(ASM..PC/ASW..PC only)

Differing to the existing standard programs,

the parameters of the AccuTec screwdrivers

can be freely assigned in some ranges. To real-

ize these special solutions, an additional PC

program is required for assignment of the

parameters. This program is on the included

USB card of the separately available USB pro-

gramming adapter. Afterwards, the data can

be transferred to the screwdriver with the

programming adapter. The current software

can be downloaded from FEIN via the Inter-

net under www.fein.com. It can be found in

the country-specific AccuTec sector.

Repair and customer service.

Before mounting or replacing application tools or accessories, remove the bat-

tery. This preventive safety measure rules out the danger of injuries through

accidental starting of the power tool.

Exchangeable parts

If required, you can change the following

parts yourself:

Application tools, battery pack

Service.

Have maintenance carried out

only through qualified person-

nel. Incorrectly mounted leads and compo-

nents can cause serious injuries. Have the

required service carried out only through a

FEIN customer service agent.

The current spare parts list for this power

tool can be found in the Internet at

www.fein.com.

Cleaning.

Remove the battery prior to

any maintenance and cleaning.

This preventive safety measure rules out the

danger of injuries through accidental starting

of the power tool.

When using in environments

with conductive dust in the air,

such as when working metals, this dust can

settle in the interior of the power tool. There-

fore, regularly blow out the interior of the

power tool from outside via the ventilation

openings with dry, oil-free compressed air;

always wear eye protection when doing this.

Do not attempt to clean

clogged or dirty ventilation

openings of the power tool with pointed

metal objects; use nonmetal tools or objects

if necessary.

Do not use cleaning agents

and solvents that can cause

damage to plastic parts. These include: Gas-

oline, carbon-tetrachloride, chloric solvents,

ammonia and domestic cleaning agents that

contain ammonia.

WARNING

CAUTION

OBJ_BUCH-0000000157-002.book Page 18 Tuesday, February 17, 2015 1:44 PM

19

en

Warranty and liability.

The warranty for the product is valid in accordance with the legal regulations in the country

where it is marketed. In addition, FEIN also provides a guarantee in accordance with the FEIN

manufacturer’s warranty declaration.

All accessories described or shown in this instruction manual will not be included with your-

power tool.

Environmental protection, disposal.

Packaging, worn out power tools and accessories should be sorted for environmental-friendly

recycling.

For further information, please contact your specialist shop.

Provided accessories (figure 13).

Fig. 13

ASW 14-6 PC

ASW 14-10 PC

ASW 14-14 PC

ASW 14-6

ASW 14-10

ASW 14-14

OBJ_BUCH-0000000157-002.book Page 19 Tuesday, February 17, 2015 1:44 PM

20

fr

Pour votre sécurité.

Lisez tous les avertisse-

ments de sécurité et

toutes les instructions. Ne pas suivre les aver-

tissements et instructions peut donner lieu à

une électrocution, un incendie et/ou une

blessure sérieuse.

Conservez tous les avertissements et toutes

les instructions pour pouvoir vous y reporter

ultérieurement.

Ne pas utiliser cet outil électrique avant

d’avoir soigneusement lu et parfaitement

compris cette notice d’utilisation y compris

les figures, les spécifications, les consignes de

sécurité ainsi que les indications marquées par

DANGER, AVERTISSEMENT et ATTEN-

TION.

N’utiliser cet outil électrique que pour les tra-

vaux pour lesquels il a été conçu par FEIN.

N’utiliser que des outils de travail et accessoi-

res autorisés par FEIN.

De même, respectez les dispositions concer-

nant la prévention des accidents du travail en

vigueur dans le pays en question.

Le non-respect des instructions de sécurité se

trouvant dans la documentation mentionnée

peut entraîner un choc électrique, un incendie

et/ou de graves blessures.

Bien garder cette notice d’utilisation en vue

d’une utilisation ultérieure ; elle doit être

jointe à l’appareil en cas de transmission ou de

vente à une tierce personne.

GARDER SOIGNEUSEMENT CES INSTRUC-

TIONS DE SECURITE.

Le terme « outil électrique » dans les consi-

gnes de sécurité fait référence à votre outil

électrique alimenté par le secteur (avec cor-

don d’alimentation) ou votre outil fonction-

nant sur batterie (sans cordon

d’alimentation).

Instructions générales de

sécurité.

1) Zone de travail

a)Conserver la zone de travail propre et

bien éclairée. Les zones en désordre ou

sombres sont propices aux accidents.

b)Ne pas faire fonctionner les outils élec-

trique en atmosphère explosive, par

exemple en présence de liquides inflam-

mables, de gaz ou de poussières. Les

outils électroportatifs produisent des

étincelles qui peuvent enflammer les

poussières ou les fumées.

c) Maintenir les enfants et les personnes

présentes à l’écart pendant l’utilisation

de l’outil. Les distractions peuvent vous

faire perdre le contrôle de l’outil.

2) Sécurité électrique

a)Il faut que les fiches de l’outil électrique

soient adaptées au socle. Ne jamais

modifier la fiche de quelque façon que

ce soit. Ne pas utiliser d’adaptateurs

avec des outils à branchement de terre.

Des fiches non modifiées et des socles

adaptés réduiront le risque de choc

électrique.

b)Eviter tout contact du corps avec des

surfaces reliées à la terre telles que les

tuyaux, les radiateurs, les cuisinières et

les réfrigérateurs. Il existe un risque

accru de choc électrique si votre corps

est relié à la terre.

c) Ne pas exposer les outils à la pluie ou à

des conditions humides. La pénétration

d’eau à l’intérieur d’un outil augmentera

le risque de choc électrique.

d)Ne pas maltraiter le cordon. Ne jamais

utiliser le cordon pour porter, tirer ou

débrancher l’outil. Maintenir le cordon à

l’écart de la chaleur, du lubrifiant, des

arêtes ou des parties en mouvement.

Des cordons endommagés ou emmêlés

augmentent le risque de choc électrique.

e) Lorsqu’on utilise un outil à l’extérieur,

utiliser un prolongateur adapté à l’utili-

sation extérieure. L’utilisation d’un cor-

don adapté à l’utilisation extérieure

réduit le risque de choc électrique.

f) Si l’usage d’un outil dans un emplace-

ment humide est inévitable, utilisez une

alimentation protégée par un dispositif

à courant différentiel résiduel (RCD).

L’usage d’un RCD réduit le risque de

choc électrique.

AVERTISSEMENT

OBJ_BUCH-0000000157-002.book Page 20 Tuesday, February 17, 2015 1:44 PM

La page charge ...

FEIN 7 112 40 Manuel utilisateur

FEIN 7 112 40 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents