Comtrend WAP-5903 Guide d'installation

Taper
Guide d'installation
! ! ! ! !Page 1
Quick Install Guide
WAP-5903 AC1200 Dual Band WiFi Mesh-Enhanced Extender
Understanding the WAP-5903 WiFi Mesh-Enhanced Extender
LED Color
LED Status
Description
Green
On
The device is connected via Ethernet cable
Blinking
The mesh system is processing
Blue
On
The device is connected to WiFi, and the connection quality is good
Blinking
The mesh system is processing
Red
On
The device is connected to WiFi, and the connection quality is weak
Blinking
The mesh system is processing
Green & Blue
Blinking
1. The device is booting up and on stand-by
2. The device has lost the uplink connection
Green & Blue &
Red
Blinking
1. The device is upgrading the firmware
2. The device is under reset to default process
Port/Button
Description
Reset
Factory Reset Function: Press and hold this button for over 10 seconds
UPLINK
Connect this port to the LAN port of the Comtrend Gateway/modem/router.
This port it used for Ethernet Pairing in a Comtrend WiFi mesh scenario.
LAN
Optional: Use this port to connect an Internet- enabled device (e.g. laptop, set-top-box, etc.).
Ethernet Port
A
Front
Back
LAN
UPLINK
Bottom
RESET
LED
! ! ! ! !Page 2
Choose One
Scenario!I:
Setup with a Comtrend Gateway that supports WifiXtend2.0
(Continue to Step B)
Scenario II:
Setup with either a non-Comtrend Gateway or
a Comtrend Gateway that does not support WifiXtend2.0
(Continue to Step E)
WifiXtend2.0is Comtrend’s WiFi Mesh technology for enhanced whole-home WiFi coverage. The WAP-5903 and
select Comtend Gatways support WifiXtend2.0™. When WifiXtend2.0™ technologies are being utilized, the WiFi
network will automatically become a single network with one SSID and Password per band.
Scenario I: Setting up the WiFi Mesh Extender with a Comtrend Gateway that
Supports WifiXtend2.0
1. Use the included Ethernet cable to connect one
end into the LAN port of the Comtrend Gateway
that supports WifiXtend2.0and the other end into
the UPLINK port of the WAP-5903.
2. Power on the WAP-5903 by connecting one end of
the Power Adapter into the Power Port of the WAP-
5903 and the other end into an outlet. The Ethernet
Pairing will automatically start processing and the
WAP-5903’s LED will begin blinking green.
3. Wait until the WAP-5903’s LED is solid green. This
means that the WAP-5903 is paired and grouped in
the same WiFi mesh network as the Comtrend
gateway.
4. If you are setting up more than one WAP-5903, then please follow instructions 1-3 with the additional WAP-
5903 units.
B
Comtrend Gateway
WAP-5903
Power Plug
Ethernet Cable
! ! ! ! !Page 3
Deploy the WiFi Mesh Extender
5. After the WAP-5903 is paired, move it to the nearest outlet where additional WiFi coverage is needed. Once
it is plugged in, wait for the LED to light up solid blue, which means it is ready.
The WiFi Mesh Network is Ready to Use!
6. The WiFi mesh network is automatically using the original WiFi configuration on the Comtrend Gateway. If
you would like to further change the network settings, then please refer to the Comtrend Gateway’s User
Manual to make changes directly to the Gateway.
Scenario II: Setting up the WiFi Mesh Extender with a Non-Comtrend
Gateway/Comtrend Gateway that does not Support WifiXtend2.0™.
Note: This scenario requires at least two WAP-5903 units to create a connection.
1. Optional: Disable the WiFi on the non-Comtrend
modem/router. This will help improve the performance
of the WiFi Mesh Extender and avoid confusing the
Internet-enabled devices.
2. Use the included Ethernet cable to connect one end
into the LAN port of the existing home modem/router
and the other end into the UPLINK port of the first WAP-
5903.
3. Power on this WAP-5903 by connecting one end of the
Power Adapter into the Power Port of the WAP-5903
and the other end into an outlet.
LED
Description
Solid
Blue
The WAP-5903 is placed in an ideal location
and is receiving a good WiFi signal.
Solid
Red
The WAP-5903 is placed too far away from
the Comtrend Gateway, and is receiving a
weak WiFi signal. Action Required: Move
the WAP-5903 closer to the Comtrend
Gateway.
D
C
E
WAP-5903
Power Plug
Ethernet Cable
Existing Modem/Router
! ! ! ! !Page 4
Setup the WiFi Network
4. You can now use your computer’s wireless configuration utility to search for a
Wireless Network name such as: Extender2368 or Extender2368-5G. (The default
SSID of this extender device is ‘Extender2368’, and 2368 is for reference. It is the
last 4 digits of the device’s MAC number.)
5. When you are prompted to input the security key, the WiFi Key (password) can
be found on the label at the back of the WAP-5903 device.
6. Click the OK button to connect to the network.
F
! ! ! ! !Page 5
7. Open your web browser, and input ‘http://extender-setup/in the address bar.
8. The system will prompt you to input the username and password. Default username is ‘rootand password is
12345’. Click the OK button to continue.
9. After logging into the Web page, input the new SSID for both the 2.4GHz and 5GHz fields. The user can
setup a new password by inputting it in both the Key fields. Click the Apply/Save button to complete setup.
10. After applying the wireless setting the WAP-5903 will reboot. When the WAP-5903’s LED is solid green it means
it is ready.
! ! ! ! !Page 6
11. You can now connect the additional WAP-5903. Power on the additional WAP-5903 by connecting one end
of the Power Adapter into the Power Port of the WAP-5903 and the other end into an outlet. The Ethernet
Pairing will automatically start processing and the WAP-5903’s LED will begin blinking green.
12. Wait until the WAP-5903’s LED is solid green. This means that the WAP-5903 is paired and grouped in the
same WiFi mesh network as the first WAP-5903.
13. You can now move the additional WAP-5903 extender to the nearest outlet where more WiFi coverage is
needed. Once plugged in, wait for the LED to light up solid blue, which means it is ready.
14.
Repeat steps 11-13 to add more WAP-5903 extenders to the mesh network.
The WiFi Mesh Network is Ready to Use!
FOR MORE HELP: For instructions on advanced features, FAQ, etc., please visit our online Product Webpage.
For more information:
YouTube: https://www.youtube.com/user/ComtrendConnection
Facebook: https://facebook.com/Comtrend
Website: http://us.comtrend.com/
Support: Visit our website or call (949) 753-9640
LED
Description
Solid
Blue
The WAP-5903 is placed in an ideal location
and is receiving a good WiFi signal.
Solid
Red
The WAP-5903 is placed too far away from
the first WAP-5903 (i.e. the one connected
to the modem/router), and is receiving a
weak WiFi signal. Action Required: Move the
WAP-5903 closer to the first WAP-5903.
G
! ! ! ! !Page 7
Federal Communication Commission Interference Statement
Radio
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and
your body.
Safety
Power Specifications(Alimentation ) :
Input: 12Vdc / 1.5A
Certification :
FCC / IC standard
Part 15B / ICES-003
Part 15C / RSS-247( 2.4GHz )
Part 15E / RSS-247( 5GHz )
1. For indoor user only
2. Do NOT use near water
3. Keep away from the fire
4. For use in ventilated environment / space
5. Do NOT open the casing
1. Cet appareil est conçu pour l'usage intérieur
seulement
2. N'utilisez pas cet appareil près de l'eau
3. N'approchez pas du feu
4. Veuillez utiliser dans un environnement aéré
5. N'ouvrez pas le boîtier
! ! ! ! !Page 8
Supplier’s Declaration of Conformity
We
Company: Comtrend Corporation - North America
Address: 530 Technology, Suite 100, Irvine CA 92618
Certify and declare under our responsibility that the following equipment:
Product Name: AC1200 Dual Band WiFi Mesh Extender
Model Name: WAP-5903
Brand Name: COMTREND
Is tested with the declaration described above, and is in conformity with the relevant FCC (Federal
Communication Commission) standards, and technical specifications have been applied:
Notes:
15.19(a)(3) Regulations :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Class B :
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
EMC:
47 CFR FCC Rules and Regulations Part 15 Subpart B , Class B Digital Device
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Comtrend WAP-5903 Guide d'installation

Taper
Guide d'installation

dans d''autres langues