Samsung DVD-V6700 Manuel utilisateur

User’s Manual

DVD-V6700

DVD-V6700S

Benutzerhanbuch

Manuel d’utilisation

Manuale dell’utente

Gebruiksaanwijzing

XEB ENG 1 5/15/07 3:48 PM Page 1

2 -

English

The lightning bolt is a warning sign alerting you to dangerous voltage inside the product.

DO NOT OPEN THE DVD-VCR. Refer to service personnel.

DO NOT expose the DVD-VCR to

extreme temperature conditions

(below 5°C and above 40°C) or to

extreme humidity conditions (less

than 10% and more than 75%).

THIS DEVICE IS NOT FOR USE IN INDUSTRIAL ENVIRONMENTS

Safety Instructions

DO NOT expose the DVD-VCR to

direct sunlight.

DO NOT expose the DVD-VCR

to any liquids.

If the remote control is not used

for a long period of time, remove

the batteries and store it in a

cool, dry place.

During a storm and/or lightning,

unplug the DVD-VCR from the

mains jack and aerial.

This product incorporates copyright protection technology that is protected by method claims of certain U.S.

patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.

Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for

home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engi-

neering or disassembling is prohibited.

The following illustrations represent precautions.

DO NOT place any objects on the

DVD-VCR or remote control.

1. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be

placed on the apparatus.

2. The Mains plug is used as a disconnect device and shall stay readily operable at any time

.

XEB ENG 1 3/24/07 11:28 AM Page 2

English

- 3

Disc Type and Characteristics

Disc Markings

• CD is recorded as a Digital Signal

with better audio quality, less distor-

tion and less deterioration of audio

quality over time.

- DO NOT play CD-ROM, CD-I and DVD-ROM in this player! (CDGs play audio only, not graphics).

- It may not play CD-R,CD-RW and DVD-R, -RW, DVD+R, +RW in all cases due to the type of disc

or condition of the recording.

- The recorded disc may not run as playback depends on the recording speed.

- Do not run the player with two discs loaded at the same time.

~

PAL

DIGITAL

SOUND

STEREO

NTSC

Play Region Number

Both the DVD-VCR and the discs are coded by

region. These regional codes must match in

order for the disc to play. If the codes do not

match, the disc will not be played.

The Region Number for this player is

described on the rear panel of the player.

Disc Types (Logos)

Recording Types

Disc Size Max. Playing Time Characteristics

Single-sided 240 min.

Double-sided 480 min.

Audio

+

Video

AUDIO-CD

DVD

• DVD contains excellent sound and

video due to Dolby Digital and

MPEG-2 system.

• Various screen and audio functions

can be easily selected through the

on-screen menu.

Audio

This DVD-VCR is capable of playing the following types of discs with the corresponding logos :

Play Region Number.

Stereo disc.

Dolby Digital disc.

Digital Audio disc.

NTSC broadcast system in U.S.A,

Canada, Korea, Japan, etc.

PAL colour system in Europe, Australia,

New Zealand, etc.

DTS disc.

Disc contains a Divx software product.

74 min.

20 min.

Single-sided 80 min.

Double-sided 160 min.

12 Cm

8 Cm

12 Cm

8 Cm

XEB ENG 1 3/24/07 11:28 AM Page 3

4 -

English

Getting Started

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Disc Type and Characteristics . . . . . . . . . . . . . . . . . . . . . . .3

Overviews . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Front View of the DVD-VCR (DVD-V6700) . . . . . . . . . . .5

Rear View of the DVD-VCR (DVD-V6700) . . . . . . . . . . . .6

Display Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Inserting Batteries in the Remote Control . . . . . . . . . . . . . . .7

Tour of the Remote Control . . . . . . . . . . . . . . . . . . . . . . . .7

Connections

Connecting DVD-VCR to the TV using the RF Cable . . . . 9

Connecting DVD-VCR to the TV using the

SCART Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting DVD-VCR to a Satellite Receiver or

Other Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting DVD-VCR to the TV using the

Audio/Video Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting DVD-VCR to the TV using the

S-Video Cable (DVD Only) . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting DVD-VCR to the TV using the

Component Video Cable (DVD Only) . . . . . . . . . . . . . . . . 11

AV Receiver Connections . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting an Audio/Video Input Cable . . . . . . . . . . . . . . 13

Plug & Auto Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Settings

Setting the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . .15

Setting the Clock Automatically . . . . . . . . . . . . . . . . . . . .15

Setting the Menu Language . . . . . . . . . . . . . . . . . . . . . . . .15

Presetting the Stations Automatically . . . . . . . . . . . . . . . . .16

Presetting the Stations Manually . . . . . . . . . . . . . . . . . . . . .17

Clearing a Preset Station . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Changing the Preset Station Table . . . . . . . . . . . . . . . . . . .18

VCR Functions

Selecting the Colour Mode . . . . . . . . . . . . . . . . . . . . . . . . .20

NICAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Intelligent Picture Control . . . . . . . . . . . . . . . . . . . . . . . . . .21

Auto Power off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Screen Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Selecting the Cassette Type . . . . . . . . . . . . . . . . . . . . . . . .22

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Selecting the Recording Speed . . . . . . . . . . . . . . . . . . . . . .23

Protecting a Recorded Cassette . . . . . . . . . . . . . . . . . . . . .23

Recording a Programme Immediately . . . . . . . . . . . . . . . . .23

Recording a Programme with Automatic Stop . . . . . . . . . .24

Recording from Another VCR or Camcorder . . . . . . . . . . . . . .24

Using the Assemble Edit Function . . . . . . . . . . . . . . . . . . .25

Using the Timer Programming Feature . . . . . . . . . . . . . . . .25

Checking a Preset Recording . . . . . . . . . . . . . . . . . . . . . . .27

Cancelling a Preset Recording . . . . . . . . . . . . . . . . . . . . . .27

Playing Back

Playing a Cassette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Adjusting Picture Alignment Manually . . . . . . . . . . . . . . . . .28

Selecting the Audio Output Mode . . . . . . . . . . . . . . . . . . . .28

Playing a Cassette in Slow Motion . . . . . . . . . . . . . . . . . . .28

Playing a Sequence Frame by Frame . . . . . . . . . . . . . . . .29

Playing a Sequence at Variable Speeds . . . . . . . . . . . . . . .29

Searching for a Specific Sequence . . . . . . . . . . . . . . . . . . .29

Using the Tape Counter . . . . . . . . . . . . . . . . . . . . . . . . . . .31

DVD Functions

Setting Up the Language Features . . . . . . . . . . . . . . . . . . .32

Setting Up the Audio Options . . . . . . . . . . . . . . . . . . . . . . .33

Setting Up the Display Options . . . . . . . . . . . . . . . . . . . . . .34

Setting Up the Parental Control . . . . . . . . . . . . . . . . . . . . . .35

DivX(R) Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Special Playback Features . . . . . . . . . . . . . . . . . . . . . . . . .38

Using the Display Function . . . . . . . . . . . . . . . . . . . . . . . . .39

Adjusting the Aspect Ratio (EZ View) . . . . . . . . . . . . . . . . .40

Selecting the Subtitle Language . . . . . . . . . . . . . . . . . . . . .41

Selecting the Audio Language . . . . . . . . . . . . . . . . . . . . . . .42

Changing the Camera Angle . . . . . . . . . . . . . . . . . . . . . . . .42

Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Marks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Repeat Chapter/Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

A to B Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

MP3/WMA Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Program & Random Play (CD/MP3/WMA) . . . . . . . . . . . . . . . .46

Picture CD Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

DivX/MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

DivX/MPEG4 Special Playback Features . . . . . . . . . . . . .49

Reference

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Troubleshooting Guide (VCR) . . . . . . . . . . . . . . . . . . . . . . .51

Troubleshooting Guide (DVD) . . . . . . . . . . . . . . . . . . . . . . .52

Contents

XEB ENG 1 3/24/07 11:28 AM Page 4

English

- 5

Overviews

1. DVD DECK.

2. OPEN/CLOSE BUTTON.

3. VIDEO CASSETE COMPARTMENT.

4. EJECT BUTTON.

5. STANDBY/ON BUTTON.

6. AUX VIDEO INPUT JACK.

7. AUX AUDIO L/R INPUT JACK.

8. PROGRESSIVE SCAN MODE BUTTON.

9. FRONT PANEL DISPLAY.

10. PROGRAMME SELECTION BUTTON.

11. DVD/VCR SELECTION BUTTON.

12. EZ VIEW BUTTON.

13. RECORD BUTTON.

14. REWIND/SKIP BACK BUTTON.

15. STOP BUTTON.

16. PLAY/STILL BUTTON.

17. FAST FORWARD/SKIP NEXT BUTTON.

Front View of the DVD-VCR (DVD-V6700)

5 6 7 8 9 10 11 12 13 14 15 16 17

1 2 3 4

XEB ENG 1 3/24/07 11:28 AM Page 5

6 -

English

1. AUDIO L, R OUT JACKS.

2. AERIAL IN CONNECTOR.

3. AV2 (DEC./EXT.) IN/OUT SCART

(EURO-21) JACK.

4. AUDIO L, R OUT JACKS (DVD only).

5. VIDEO OUT JACK.

6. OUT TO TV CONNECTOR.

7. AV1 (EURO AV) IN/OUT SCART.

(EURO-21) JACK.

8. DIGITAL AUDIO OUT JACKS (COAXIAL).

9. COMPONENT VIDEO OUT JACKS.

10. S-VIDEO OUT JACK.

1. The DVD Deck is active.

2. Disc is loaded.

3. The time, counter position, current deck

status is displayed.

4. VHS tape is inserted.

5. The VCR Deck is active.

6. A Timer Recording is programmed or in

progress.

6

1 2 3 4 5

Rear View of the DVD-VCR (DVD-V6700)

Display Indicators

5 6 7 8 9 10

1 2 3 4

XEB ENG 1 3/24/07 11:28 AM Page 6

English

- 7

Make sure that the following basic accessories

are supplied with your DVD-VCR.

You must insert or replace the batteries in the

remote control when you:

• Purchase the DVD-VCR

• Find that the remote control is no longer

working correctly

1 To release the battery compartment cover,

push the tab in the direction of the arrow and

lift up.

2 Insert two AAA, RO3 or equivalent batteries,

taking care to respect the polarities:

• + on the battery with + on the remote

control.

• – on the battery with – on the remote

control.

Do not mix different battery types (manganese

and alkaline for example).

3 Replace the cover by aligning it with the base

of the remote control and push it down.

Batteries for

remote controls

Remote Control

Audio & Video

Cable

RF-Cable

Owner’s

Instructions

Accessories

Inserting Batteries in the Remote

Control

Tour of the Remote Control

1

21

5

19

18

17

16

4

23

22

24

6

26

25

10

9

7

8

29

14

28

27

13

12

11

30

15

20

2

3

XEB ENG 1 3/24/07 11:28 AM Page 7

8 -

English

1. DVD,VCR

Used to operate DVD, VCR.

2. STANDBY/ON

Used to turn the power on or off.

3. Number buttons

4. TIMER

Used to activate the timer recording of

a programme.

5. REC ( ● )

Used to make a recording on cassette.

6. SKIP ( / )

Use to skip a title, chapter or track.

7. STOP ( ■ )

Used to stop during playback.

8. AUDIO

Used to access various audio functions.

9. TRK ( / )

Used to adjust picture alignment manually to

obtain the best possible picture during play-

back.

10. MENU

Used to display the on-screen menu.

11. OK



/



,

¦¦

/



Used to control the cursor in the on-screen

menu and confirm your choice.

12. EZ VIEW

Used to adjust the aspect ratio on a disc.

13. DISC MENU

Used to display a disc menu.

14. SUBTITLE

Used to change the DVD’s subtitle language.

15. ANGLE

Used to access various camera angles on a

DVD.

IPC (Intelligent Picture Control).

Used to adjust the sharpness of the picture.

16. INPUT SEL.

Used to select a external input signal.

17. TV/VCR

Used to select TV or VCR.

18. INFO.

Used to display the current setting or disc

status.

19. OPEN/CLOSE

Used to open and close the disc and video

cassette tray.

20. SHUTTLE

Used to play a sequence at variable speeds.

21. F.ADV/STEP

Used to advance a sequence frame by

frame.

22. SPEED

Used to select the recording speed.

23. PLAY/PAUSE ( )

Used to play or pause during playback.

24. SEARCH ( / )

Used to search forward or backward through

a disc.

25. PROG

Used to select a TV programme.

26. RETURN

Used to return to a previous menu.

27. ZOOM

Used to enlarges picture .

28. CLEAR

Used to clear a preset TV station.

Used to cancel a preset recording.

Used to cancel a preset mark.

Used to set the tape counter to zero.

Used to resume normal play during repeat

play.

29. MARK

Used to mark a position during playback a

disc.

SEARCH

Used to search for a specific sequence.

30. MODE

Used to select the programme or random

play.

REPEAT

Used to allow the repeat play a title, chapter,

track, disc or A-B.

XEB ENG 1 3/24/07 11:28 AM Page 8

English

- 9

TV

RF cable

Aerial

5

TV

RF cable

Aerial

2

3

4

1

2

3

Connecting DVD-VCR to the TV

using the RF Cable

To receive television programmes a signal must

be received from one of the following sources:

• An outdoor aerial.

• An indoor aerial.

• A cable television network.

• A satellite receiver.

1 Remove the aerial or network input cable

from the television.

2 Connect this cable to the 75Ω coaxial jack

marked on the rear of your DVD-VCR.

3 Plug the RF Cable supplied into the jack

on your DVD-VCR.

4 Plug the other end of the RF Cable into the

connector previously used for the aerial on

the television.

TV

• Make sure that both the television and the

DVD-VCR are switched off before connect-

ing the cables.

Note

C

onnections

Connecting DVD-VCR to the TV

using the SCART Cable

You thus:

• Obtain better quality sound and pictures.

• Simplify the setting up procedure of your

DVD-VCR.

1 Connect the Aerial Cable.

2 Connect one end of the SCART cable to the

AV1 (EURO AV) jack on the rear of the DVD-

VCR.

3 Plug the other end into the appropriate

connector on the television.

Connecting the Audio Output

Cable

You can connect your DVD-VCR to a Hi-Fi

system. Example: You wish to take advantage of

the quality of your Hi-Fi stereo system when

watching a disc play.

4 Plug the audio output cable into the audio

connectors on the rear of your DVD-VCR.

5 Plug the other end of the audio cable into the

appropriate input connectors on your Hi-Fi

stereo system.

•

Regardless of the type of connection chosen,

you must always connect the RF Cable supplied.

Otherwise, no picture will be visible on the

screen when the DVD-VCR is switched off.

• Make sure that both the television and the DVD-

VCR are switched off before connecting the

cables.

Note

You can connect your DVD-VCR to the television

using the SCART cable if the appropriate input is

available on the television.

XEB ENG 2 4/21/07 4:16 PM Page 9

10 -

English

Connecting DVD-VCR to the TV

using the Audio/Video Cable

You can connect your DVD-VCR to the televi-

sion using the audio/video cable if the appropri-

ate input is available on the television.

1 Connect one end of the video cable into the

VIDEO output jack on the rear of the DVD-

VCR.

2 Plug the other end of the video cable into the

appropriate input connector on the television.

3 Connect one end of the audio cables supplied

into the AUDIO output jacks on the rear of the

DVD-VCR.

• Take care to respect the colour coding of

the left and right channels.

4 Plug the other end of the audio cables into

the appropriate input connectors on the televi-

sion.

You can connect your DVD-VCR to a Satellite

receiver or other DVD-VCR using the SCART

cable if the appropriate outputs are available on

the equipment chosen. The following illustra-

tions give a few examples of the connection

possibilities.

1

AV2(EURO AV): By means of 21-pin Scart

Cable

Plug the SCART Cable with satellite receiver

or other equipment into the AV2 (EURO AV)

jack on the rear of the DVD-VCR.

After making this connection, select the

source by pressing the INPUT SEL. button

for the AV2 input sources.

2 By means of RF Cable

After making this connection, you must preset

the station received through the satellite

tuner.

3 AV1 (EURO AV) : By means of 21-pin Scart

Cable

Connect the end of the SCART cable to the

AV1(EURO AV) jack on the rear of the DVD-

VCR. Plug the other end into the appropriate

connector on the television.

Connecting DVD-VCR to a Satellite

Receiver or Other Equipment

SCART cable

RF cable

Aerial

1

2

3

Satellite Receiver or other Equipment

AV (TV)

Aerial Connector

TV

3

1

4

2

XEB ENG 2 3/24/07 11:47 AM Page 10

English

- 11

Connecting DVD-VCR to the TV

using the S-Video Cable (DVD only)

You will enjoy high quality images. S-Video

seperates the picture element into black and

white(Y) and colour(C) signals to present clearer

images than regular video input mode.

1 Connect one end of the S-Video cable into

the S-VIDEO output jack on the rear of the

DVD-VCR.

2 Plug the other end of the S-Video cable into

the appropriate input connector on the televi-

sion.

3 Connect one end of the audio cables supplied

into the AUDIO LINE output jacks on the rear

of the DVD-VCR.

• Take care to respect the colour coding of

the left and right channels.

4 Plug the other end of the audio cables into

the appropriate input connectors on the televi-

sion.

• Use the S-Video connection method only for

the DVD.

Connecting DVD-VCR to the TV

using the Component Video Cable

(DVD only)

Your TV must support progressive scan input to

allow you to watch component video output.

You will enjoy high quality accurate colour repro-

duction images. Component video seperates the

picture element into black and white (Y), blue

(Pb), red (Pr) signals to present most clear and

clean images.

1 Connect Component video cables between

the COMPONENT VIDEO OUT jacks on the

rear of the DVD-VCR and COMPONENT

VIDEO IN jacks on the rear of the TV.

2 Connect audio cables between the AUDIO

LINE OUT jacks on the rear of the DVD-VCR

and AUDIO IN jacks on the rear of the TV.

• Take care to respect the colour coding of

the left and right channels.

3

2

4

1

COMPONENT VIDEO OUT

COMPONENT INPUT

COMPONENT VIDEO IN

1

2

Note

XEB ENG 2 3/24/07 11:47 AM Page 11

12 -

English

AV Receiver Connections

Digital Audio out Jack

To take full advantage of the movie theater

experience that DVD offers, you may want to

connect your DVD-VCR to a complete Surround

Sound system, including an A/V Receiver and

six Surround Sound speakers. If your A/V

receiver is equipped with a Dolby Digital

Decoder, you have the option to bypass the

DVD-VCR’s built-in Dolby Digital Decoder. Use

the Digital Audio Out connection below.

1 Connect a Digital Audio coaxial cable from the

Digital Audio Out jacks on the panel of the DVD-

VCR to their corresponding Digital Audio Input

jacks on your A/V Receiver:

To Digital Audio Input of an A/V Receiver

with a Dolby, MPEG2, DTS, Digital Decoder

Progressive Scan (DVD only)

If the TV connected supports Progressive Scan,

press the P.SCAN button on the front panel in

stop mode.

• The message “Press OK to confirm

Progressive scan mode. Otherwise press

RETURN.” will be displayed. If you want

Progressive scan mode, select OK. Make sure

that the disc has stopped completely before

changing the mode.

• To cancel the progressive scan mode, press

the P.SCAN button in stop mode.

• Do not press the P.SCAN button if you are

using a TV that does not support Progressive

mode. Nothing will be displayed on the screen

if pressed. To release the Progressive mode,

press the P.SCAN button in stop mode.

• See your TV User’s Manual to find out if your

TV supports Progressive Scan. If Progressive

Scan is supported, follow the TV User’s

instructions regarding Progressive Scan set-

tings in the TV’s menu system.

• Depending on your TV, the method of connec-

tion may differ from the illustration above.

• What is "Progressive Scan"? Progressive scan

has twice as many scanning lines as the inter-

lace output method has. Progressive scanning

method can provide better and clearer picture

quality.

• You must connect the player to the compo-

nent(s) before using the Progressive Scan fea-

ture.

• Make sure that the colour coded connections

match. That is, the Y, Pb and Pr component

output jacks of your DVD -VCR should be con-

nected to the exact corresponding component

input jacks on your TV. Otherwise, red or blue

images will be displayed on the TV screen.

• NTSC DVD disc is not supported.

Note

XEB ENG 2 3/24/07 11:47 AM Page 12

English

- 13

Connecting an Audio/Video Input

Cable

You can connect other audio/video equipment to

your DVD-VCR using audio/video cables if the

appropriate outputs are available on the equip-

ment chosen.

Examples :

• You wish to copy a video cassette with the

help of a second VCR.

• You wish to play and/or copy pictures taken

with a camcorder.

• Make sure that both the external devices and

the DVD-VCR are switched off before connect-

ing the cables.

1 Connect one end of the video cable into the

VIDEO input jack on the front of the DVD-

VCR.

2 Plug the other end of the video cable into the

appropriate output connector on the other

system (VCR or Camcorder, etc).

3 Connect one end of the audio cable supplied

into the AUDIO input jacks on the front of the

DVD-VCR.

• Take care to respect the colour coding of

the left and right channels.

4 Plug the other end of the audio cable into the

appropriate output connectors on the other

system (VCR, camcorder, etc).

2

3

1

4

Plug & Auto Setup

Your DVD-VCR will automatically set itself up

when it is plugged into the mains for the first

time. TV stations will be stored in memory. The

process takes a few minutes. Your DVD-VCR

will then be ready for use.

1 Connect the RF Cable as indicated on page

9. (Connecting Your DVD-VCR to the TV

using the RF Cable).

2 Plug the DVD-VCR into the mains.

• “AUTO” in the front panel display flickers.

3 The Language Set menu is displayed.

4 Press the  or  button to select the desired

language, then press OK button.

Start the auto setup.

OK RETURN MENU



English

Français

Deutsch

Español

Italiano

Nederlands

Language Set

Auto Setup will be

started.

Check antenna and TV

cable connection.

OK RETURN MENU

XEB ENG 2 3/24/07 11:47 AM Page 13

14 -

English

5 Press the //¦ / buttons to select your

Country.

The Country Selection menu is displayed.

• Refer to following abbreviation table when

selecting “Country”.

• The DVD-VCR searches for the station

according to a preset preference list

corresponding to the country that you have

selected.

6 Press the OK button.

Start the auto scanning.

The number of stations automatically stored

by the DVD-VCR depends on the number of

stations that it has found.

Please Wait

10%



RETURN MENU

Auto Setup

MENU

RETURN

OK

Country Selection

ANLS PL

BI CHCZ

DK N TR Others

FIN P GR

DE HU

7 The current time and date are displayed

automatically.

Check the Date and Time if it is :

• Incorrect, refer to “Setting the Date and

Time”. (See page 15)

• Correct, press the RETURN button twice to

exit the menu.

SETUP

VCR

PROG

FUNC

DVD

OK RETURN MENU

Clock Set

Time Date Year

12 : 00 01 / JAN / 2007 MON

Auto Clock : On

A(Austria) NL(Netherlands) S(Sweden) PL(Poland)

B(Belgium) I(Italy) CH(Swiss) CZ(Czech)

DK(Denmark) N(Norway) TR(Turkey) Others

FIN(Finland) P(Portugal) GR(Greece)

D(Deuthland) E(Spain) HU(Hungary)

• Now, you only have to switch the DVD-VCR

on and it is ready for use.

• Function for “Plug & Auto Set Up” is fixed already.

So if you want to change this fixed one, you can

change. (refer to “Presetting the Stations Manually”

page 17).

Note

XEB ENG 2 3/24/07 11:47 AM Page 14

English

- 15

Your DVD-VCR contains a 24-hour clock and

calendar used to:

• Automatically stop programme recording.

• Preset your DVD-VCR to record a programme

automatically.

You must set the date and time when:

• You purchase the DVD-VCR.

• Do not forget to reset the time when you

change clocks from winter to summer time

and vice versa.

1 Press the MENU button, then press the OK or

 button.

2 Press the  or  button to select Clock,

then press the OK or  button.

The Clock Set menu is displayed.

3 Press the ¦ or  button to select the hour,

minutes, day, month, and year. The selected

option is highlighted. Press the  or  button

to set them. The day of the week is displayed

automatically. Press the OK button.

• You can hold down the  or button to

scroll more quickly through the values.

• Press the MENU button to exit the menu.

Setting the Date and Time

OK

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

MENU

RETURN

OK

Clock Set

SETUP

VCR

PROG

FUNC

DVD

Time Date Year

12 : 00 01 / JAN / 2007 MON

Auto Clock : On

S

ettings

Setting the Menu Language

1 Press the MENU button, then press the OK or

 button.

2 Press the OK or  button again.

The Language Set menu is displayed.

3 Press the  or  button to select desired

language, then press the OK or  button.

• Press the MENU button to exit the menu.

OK RETURN MENU



English

Français

Deutsch

Español

Italiano

Nederlands

Language Set

Setting the Clock Automatically

4 Press the ¦ or  button to select Auto

Clock. Press the  or  button to select On.

OK

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

SETUP

VCR

PROG

FUNC

DVD

OK RETURN MENU

Clock Set

Time Date Year

12 : 00 01 / JAN / 2007 MON

Auto Clock : On

XEB ENG 3 3/24/07 1:12 PM Page 15

4 Press the OK button. A message is displayed,

indicating that any channels already preset on

your DVD-VCR will be deleted.

16 -

English

5 Press the OK button to start the auto scan-

ning. The message Please Wait is displayed.

• The first frequency band is scanned and

stored, then the DVD-VCR searches for the

second station and so on.

When the automatic scanning procedure

has finished, the DVD-VCR switches

automatically to programme 1.

• If you wish to cancel the auto scanning

before the end, press the MENU button.

• The number of stations automatically stored by the

DVD-VCR depends on the number of stations that

it has found.

• The time and date are set automatically from the

broadcast signal. If the signal is weak or ghosting

occurs, the time and date may not be set automati-

cally. In this case, they should be set manually

(refer to page 15).

• Once the auto scanning procedure has finished,

some stations may have been stored more than

once; select the stations with the best reception

and delete the ones no longer required (refer to

page 18).

Presetting the Stations

Automatically

You do not need to preset the stations if you

have already set them automatically (refer to

“Plug & Auto Set Up” on page 13).

Your DVD-VCR contains a built-in tuner used to

receive television broadcasts.

You must preset the stations received through

the tuner. This can be done:

• Plug & Auto Set up (refer to page 13).

• Automatically.

• Manually (refer to page 17).

You can store up to 80 stations.

1 Press the MENU button, then press the

OK or  button.

2 Press the  or  button to select Install,

then press the OK or  button.

The Install menu is displayed.

3 Press the OK or  button. The Country

Selection menu is displayed. Press the  or

,¦ or  buttons to select your country.

OK RETURN MENU

Your data will be lost

Press OK to continue

MENU to exit

Auto Setup

OK

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

Please Wait

10%



RETURN MENU

Auto Setup

Note

OK

SETUP

VCR

PROG

FUNC

DVD

Install

RETURN MENU

Auto Setup



Manual Setup



Country Selection

ANLS PL

BI CHCZ

DK N TR Other

FIN P GR

DE HU

OK RETURN MENU

XEB ENG 3 3/30/07 10:31 AM Page 16

English

- 17

You do not need to preset the stations manually

if you have already set them automatically.

1 Press the MENU button, then press the OK or

 button.

2 Press the  or  button to select Install,

then press the OK or  button.

The Install menu is displayed.

3 Press the  or  button to select Manual

Setup, then press the OK or  button.

The TV STATION TABLE menu is displayed.

4 Press the  or  button to select the

required programme number.

5 Press the  button to preset the station.

The MANUAL TUNING menu will be dis-

played.

Press the ¦ or  button to start scanning the

channels. The frequency band is scanned and

the first station found is displayed.

Presetting the Stations Manually

OK

SETUP

VCR

PROG

FUNC

DVD

Install

RETURN MENU

Auto Setup



Manual Setup



OK

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

Select a character

in the name.

Move to the next

previous or

character

Press the  or button until the

required character is displayed

(letters, numbers or “-” character).

Press the ¦ or  button

respectively.

To... Then...

6 If necessary, press the  or  button to

select MFT, then press the ¦ or  button to

adjust the picture.

7 Press the  or  button to select

DECODER.

Then press the ¦ or  button to select

decoder ON or OFF .

8 Press the  or  button to select NAME.

The station name is set automatically from the

broadcast signal.

• To change the programme’s name, press

the  button. The first letter of the name

flashes.

9

If you... Then...

Wish to store the

station displayed

Do not wish to

store the station

displayed

•

Press OK to store the

station.

•

Press the  or button until

the CH is selected.

•

Press the ¦ or  button to

go on scanning the

frequency band and display

the next station.

¦¦

MEMORY : OK

RETURN

❉ ❉ MANUAL TUNING. ❉ ❉

SYSTEM : L/L’

PR : 1

CH : 021

MFT : -

DECODER : OFF

NAME : - - - -



SWAPPING : OK

DELETE : CLEAR RETURN

❉ ❉ TV STATION TABLE ❉ ❉

PR CH NAME DEC SYSTEM

1 021

- - - - OFF L/L’

2

3

4

5

¦¦

MEMORY : OK

RETURN

❉ ❉ MANUAL TUNING. ❉ ❉

SYSTEM : L/L’

PR : 1

CH : 021

MFT : -

DECODER : OFF

NAME : - - - -

XEB ENG 3 3/30/07 3:44 PM Page 17

18 -

English

If you have stored a TV station:

• That you do not require

• At the wrong programme position, you can

cancel it.

1 Press the MENU button, then press the OK or

 button.

2 Press the  or  button to select Install,

then press the OK or  button.

The Install menu is displayed.

3 Press the  or button to select Manual

Setup, then press the OK or  button.

The TV STATION TABLE menu is displayed.

4 Press the  or  button to select required

preset TV station.

Press the CLEAR button to delete.

5 Repeat the same procedure from step 4

onwards until all the required stations have

been cleared.

Clearing a Preset Station

OK

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

10 Repeat this procedure from step 4 onwards,

until all the required stations have been

stored.

11 Press the MENU button to exit the menu.

Changing the Preset Station Table

You can rearrange the station table and give

different programme numbers to the stations

listed according to your own preferences.

1 Press the MENU button, then press the OK or

 button.

2 Press the  or  button to select Install,

then press the OK or  button. The Install

menu is displayed.

3 Press the  or button to Select Manual

Setup, then press the OK or  button.

The TV STATION TABLE menu is displayed.

4 Press the  or  button to select required

preset TV station. The selected station is dis-

played at the same time on the television

screen.

5 Press the OK button to change the

programme number assigned to a station.

OK

SETUP

VCR

PROG

FUNC

DVD

Install

RETURN MENU

Auto Setup



Manual Setup



OK

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU



SWAPPING : OK

DELETE : CLEAR RETURN

❉ ❉ TV STATION TABLE ❉ ❉

PR CH NAME DEC SYSTEM

1 021

- - - - OFF L/L’

2

3

4

5



SWAPPING : OK

DELETE : CLEAR RETURN

❉ ❉ TV STATION TABLE ❉ ❉

PR CH NAME DEC SYSTEM

1 021

- - - - OFF L/L’

2

3

4

5

XEB ENG 3 3/30/07 9:02 AM Page 18

English

- 19

6 Press the  or  button to select required

position, then press the OK button to swap

the position.

For example to move a TV station in

programme 1 to programme 3.

• Press the MENU button to exit the menu.



SWAPPING : OK

DELETE : CLEAR RETURN

❉ ❉ TV STATION TABLE ❉ ❉

PR CH NAME DEC SYSTEM

1

2

3 021

- - - - OFF L/L’

4

5

XEB ENG 3 3/30/07 3:44 PM Page 19

20 -

English

Before recording or playing back a cassette,

you can select the required system standard.

Otherwise, the system automatically selects the

reception standard when you select AUTO.

• When playing back a cassette, the standard is

automatically selected by the DVD-VCR.

• When you playback an NTSC-recorded tape

on this DVD-VCR make a setting on the colour

system according to your TV. If your TV is a

PAL system only TV, set NTPB. If your TV is

multi system TV (NTSC 4.43 compatible), set

NT4.43 and you can record NT4.43.

1 Press the MENU button, then press the OK

or  button.

2 Press the  or  button to select User Set,

then press the OK or  button.

The User Set menu is displayed.

3 Press the OK or button to select required

colour system. Auto ➝ PAL ➝ B/W

• Auto: When playing back a cassette,

the system standard is automatically

selected by the DVD-VCR.

• B/W: Black and White.

Selecting the Colour Mode

V

CR

F

unctions

OK

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

NICAM programmes are divided into 3 types.

NICAM Stereo, NICAM Mono and Bilingual (trans-

mission in another language).

NICAM programmes are always accompanied by a

standard mono sound broadcast and you can

select the desired sound. Please refer to page 29.

1 Press the MENU button, then press the OK or

 button.

2 Press the  or  button to select User Set,

then Press the OK or  button.

The User Set menu is displayed.

3 Press the  or  button to select NICAM, then

press the OK or  button to select On or Off.

• On (for NICAM mode):

Normally set at this position

• Off (for MONO mode):

Only set at this position to record the standard

mono sound during a NICAM broadcast if the

stereo sound is distorted due to inferior

reception conditions.

NICAM

OK

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

OK

SETUP

VCR

PROG

FUNC

DVD

RETURN MENU

User Set

Colour System : Auto



NICAM : On



IPC : On



OK

SETUP

VCR

PROG

FUNC

DVD

RETURN MENU

User Set

Colour System : Auto



NICAM : On



IPC : On



XEB ENG 3 3/24/07 1:12 PM Page 20

La page charge ...

Samsung DVD-V6700 Manuel utilisateur

Ce manuel convient également à

Samsung DVD-V6700 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents