Eaton Power Xpert 9395P Guide d'installation
- Taper
- Guide d'installation
®
Eaton Power Xpert™ 9395 High Performance* Field Installed UPM
Mechanical Installation Manual
*Referenced throughout as 9395P
®
Eaton Power Xpert™ 9395 High Performance* Field Installed UPM
Mechanical Installation Manual
*Referenced throughout as 9395P
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and maintenance of the UPS and batteries. Please
read all instructions before operating the equipment and save this manual for future reference.
CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSERVER CES INSTRUCTIONS
Ce manuel comporte des instructions importantes que vous êtes invité à suivre lors de toute procédure d'installation et de maintenance
des batteries et de l'onduleur. Veuillez consulter entièrement ces instructions avant de faire fonctionner l'équipement et conserver ce
manuel afin de pouvoir vous y reporter ultérieurement.
W A R N I N G
This is a product for restricted sales distribution to informed partners (EN/IEC 62040-2). Installation restrictions or additional measures
may be needed to prevent electromagnetic disturbances.
AVERTISSMENT
Les ventes et la distribution de ce produit sont limitées aux partenaires avisés (EN/CEI 62040-2). Des restrictions en matière d’installation
ou des mesures supplémentaires sont parfois nécessaires pour éviter les perturbations électromagnétiques.
Eaton is a registered trademark of Eaton Corporation or its subsidiaries and affiliates.
ECopyright 2015 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be reproduced in any way without the
express written approval of Eaton Corporation.
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
i
Table of Contents
1 Introduction 1-1............................................................................
1.1 Using This Manual 1-1....................................................................................
1.2 Conventions Used in This Manual 1-1..........................................................................
1.3 Symbols, Controls, and Indicators 1-3..........................................................................
1.4 For More Information 1-3...................................................................................
1.5 Getting Help 1-4.........................................................................................
2 Safety Warnings 2-1........................................................................
3 Field Installed UPM Installation Plan and Unpacking 3-1...........................................
3.1 Creating an Installation Plan 3-1.............................................................................
3.2 Preparing the Site 3-1.....................................................................................
3.3 Inspecting and Unpacking the FI-UPM Cabinet 3-6.................................................................
4 Field Installed UPM Installation 4-1............................................................
4.1 Preliminary Installation Information 4-1........................................................................
4.2 Unloading the FI-UPM Cabinet from the Pallet 4-1.................................................................
4.3 Mechanical Installation 4-3.................................................................................
4.4 Electrical Installation 4-5...................................................................................
4.5 Initial Startup 4-5........................................................................................
4.6 Completing the Installation Checklist 4-5.......................................................................
5 Warranty W-1..............................................................................
TABLE OF CONTENTS
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
ii
List of Figures
Figure 1-1. Power Xpert 9395P Field Installed UPM 1-2.............................................................
Figure 3‐1. FI-UPM Cabinet Dimensions (Front View) 3-3............................................................
Figure 3‐2. FI-UPM Cabinet Dimensions (Right Side View) 3-4........................................................
Figure 3‐3. FI-UPM Cabinet Dimensions (Top View) 3-4.............................................................
Figure 3‐4. FI-UPM Cabinet Dimensions (Bottom View) 3-5..........................................................
Figure 3‐5. FI-UPM Cabinet Dimensions (Bottom View with Mounting Brackets) 3-5........................................
Figure 3‐6. FI-UPM Cabinet Center of Gravity 3-6.................................................................
Figure 3‐7. Power Xpert 9395P FI-UPM Cabinet as Shipped on Pallet 3-8................................................
Figure 4-1. Removing the Left Side Shipping Bracket 4-2............................................................
Figure 4-2. Removing the Right Side Shipping Bracket 4-3...........................................................
Figure 4-3. UPS Cabinet Wire Entry Plate and Knockout Locations 4-4..................................................
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
1-1
Chapter 1 Introduction
The Power Xpert
®
9395P Field Installed UPM (FI-UPM) provides increased capacity or
N+1 redundancy for Power Xpert 9395P UPS systems. Capacity increase depends on
the capabilities of the originally installed system. The FI-UPM may be installed at any
time when power needs change. The module cabinet installs on the left side of the
UPS cabinet and wires directly to the UPS. No input or output wiring changes are
needed for a capacity increase if the original installation was wired with increased
capacity in mind. Operation remains the same as the original UPS.
The FI-UPM is housed in a single, free‐standing cabinet with safety shields behind the
front panel for hazardous voltage protection. The cabinet matches the UPS cabinet in
style and color. Figure 1‐1 shows the Power Xpert 9395P FI-UPM.
NOTE Wiring, startup, and operational checks must be performed by an authorized Eaton Customer Service
Engineer, or the warranty terms specified on page W-1 become void. This service is offered as part of the
sales contract for the FI-UPM. Contact an Eaton service representative in advance (usually a two-week notice
is required) to request service.
1.1 Using This Manual
This manual describes how to mechanically install the Power Xpert 9395P FI-UPM
cabinet. Electrical installation will be performed by an Eaton Customer Service
Engineer. Read and understand the procedures described in this manual to ensure
trouble-free installation.
1.2 Conventions Used in This Manual
This manual uses these type conventions:
S Bold type highlights important concepts in discussions, key terms in procedures,
and menu options, or represents a command or option that you type or enter at a
prompt.
S Italic type highlights notes and new terms where they are defined.
S Screen type represents information that appears on the screen or LCD.
Icon Description
Information notes call attention to important features or instructions.
[Keys] Brackets are used when referring to a specific key, such as [Enter] or [Ctrl].
In this manual, the term UPS refers only to the UPS cabinet and its internal elements.
The term UPS system refers to the entire power protection system – the UPS
cabinet, the battery cabinet, and options or accessories installed.
Figure
INTRODUCTION
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
1-2
Figure 1‐1. Power Xpert 9395P Field Installed UPM
INTRODUCTION
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
1-3
1.3 Symbols, Controls, and Indicators
The following are examples of symbols used on the UPS or accessories to alert you
to important information:
RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric
shock symbol.
CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's manual for
additional information, such as important operating and maintenance instructions.
This symbol indicates that you should not discard the UPS or the UPS batteries in the
trash. This product contains sealed, lead‐acid batteries and must be disposed of
properly. For more information, contact your local recycling/reuse or hazardous waste
center.
This symbol indicates that you should not discard waste electrical or electronic
equipment (WEEE) in the trash. For proper disposal, contact your local recycling/reuse
or hazardous waste center.
1.4 For More Information
Refer to the following manuals for additional information:
S Eaton Power Xpert 9395P UPS (650 900 kVA) Installation and Operation Manual
S Eaton Power Xpert 9395P UPS (1000-1200 kVA) Installation and Operation Manual
These manuals describe:
S UPS cabinet, optional components, and accessory installation instructions,
including site preparation, planning for installation, and wiring and safety
information. Detailed illustrations of cabinets and optional accessories with
dimensional and connection point drawings are provided.
S UPS operation, including UPS cabinet controls, functions of the UPS, standard
features and optional accessories, procedures for starting and stopping the UPS,
and information about maintenance and responding to system events.
S Communication capabilities of the UPS system.
Visit www.eaton.com/powerquality or contact Eaton service representative for
information on how to obtain copies of these manuals.
INTRODUCTION
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
1-4
1.5 Getting Help
If help is needed with any of the following:
S Scheduling initial startup
S Regional locations and telephone numbers
S A question about any of the information in this manual
S A question this manual does not answer
Please call the Eaton Help Desk at:
United States:
1-800-843-9433 or 1-919-870-3028
Canada: 1-800-461-9166 ext 260
All other countries: Call your local service representative
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
2-1
Chapter 2 Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that should be followed during installation of the Field Installed
UPM (FI-UPM ). Read all instructions before operating the equipment and save this manual for future
reference.
The FI-UPM cabinet is designed for industrial or computer room applications, and contains safety shields
behind the panel. However, the FI-UPM is a sophisticated power system and should be handled with
appropriate care.
D A N G E R
The FI-UPM contains LETHAL VOLTAGES. All repairs and service should be performed by AUTHORIZED
SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS inside the FI-UPM.
D A N G E R !
Cet FI-UPM peut générer des TENSIONS MORTELLES. L’installation et l’entretien ne doivent être effectués
que par le PERSONNEL AUTORISÉ. Ne contient AUCUNE PIÈCE REMPLAÇABLE.
W A R N I N G
S The UPS system contains its own energy source (batteries). The output terminals may carry live voltage
even when the UPS is disconnected from an AC source.
S To reduce the risk of fire or electric shock, install this UPS and FI-UPM in a temperature and humidity
controlled, indoor environment, free of conductive contaminants. Ambient temperature must not exceed
40C (104F). Do not operate near water or excessive humidity (95% maximum). The system is not
intended for outdoor use.
S Ensure all power is disconnected before performing installation or service.
S ELECTRIC ENERGY HAZARD. Do not attempt to alter any battery wiring or connectors. Attempting to alter
wiring can cause injury.
A V E R T I S S E M E N T !
S L’onduleur est alimenté par sa propre source d’énergie (batteries). Les bornes de sortie peuvent être sous
tension, même lorsque l’onduleur est débranché d’une source de courant alternatif.
S Pour réduire les risques d’incendie et de décharge électrique, installer l’onduleur à l’intérieur, dans un
endroit exempt d’éléments conducteurs et où la température et l’humidité sont régulées. La température
ambiante ne doit pas dépasser 40C (104F). Ne pas faire fonctionner près d’une source d’eau ou dans
un endroit très humide (95 % maximum). Le système n’est pas conçu pour une utilisation extérieure.
S Toutes les sources d’alimentation doivent être débranchées avant de procéder à l’installation et à
l’entretien.
S DANGERS ÉLECTRIQUES. Ne pas tenter de modifier le câblage et les connecteurs de l’onduleur ou des
batteries. Toute tentative de modification peut provoquer des blessures.
C A U T I O N
S Keep the FI-UPM front panel installed to ensure proper cooling airflow and to protect personnel from
dangerous voltages inside the unit.
S Do not install or operate the UPS system or FI-UPM close to gas or electric heat sources.
Figure
SAFETY WARNINGS
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
2-2
S The operating environment should be maintained within the parameters stated in this manual.
S Keep surroundings uncluttered, clean, and free from excess moisture.
S Observe all DANGER, CAUTION, and WARNING notices affixed to the inside and outside of the
equipment.
A T T E N T I O N !
S Garder les portes de l’onduleur fermées et les panneaux avant en place pour garantir une circulation
adéquate de l’air de refroidissement et pour protéger le personnel des tensions dangereuses dans
l’unité.
S Ne pas installer ni faire fonctionner l’onduleur près d’une source de chaleur au gaz ou à l’électricité.
S Le milieu de fonctionnement doit toujours correspondre aux paramètres établis dans ce manuel.
S Maintenir les lieux rangés, propres et exempts d’une humidité excessive.
S Respecter les étiquettes DANGER, MISE EN GARDE et AVERTISSEMENT se trouvant à l’intérieur et à
l’extérieur de l’équipement.
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
3-1
Chapter 3 Field Installed UPM Installation Plan and Unpacking
Use the following basic sequence of steps to install the Field Installed UPM (FI-UPM):
1. Create an installation plan for the FI-UPM (Chapter 3).
2. Prepare your site for the FI-UPM (Chapter 3).
3. Inspect and unpack the FI-UPM cabinet (Chapter 3).
4. Unload and install the FI-UPM cabinet (Chapter 4).
5. Complete the Installation Checklist (Chapter 4).
6. Have authorized service personnel install wiring, perform preliminary operational
checks, and start up the system.
NOTE Wiring, startup, and operational checks must be performed by an authorized Eaton Customer Service
Engineer, or the warranty terms specified on page W-1 become void. This service is offered as part of the
sales contract for the FI-UPM. Contact an Eaton service representative in advance (usually a two-week notice
is required) to request service.
3.1 Creating an Installation Plan
Before installing the FI-UPM, read and understand how this manual applies to the
system being installed. Use the procedures and illustrations in paragraph 3.2 and
Chapter 4 to create a logical plan for installing the system.
3.2 Preparing the Site
For the FI-UPM to operate at peak efficiency, the installation site should meet the
environmental parameters outlined in this manual. If the FI-UPM is to be operated at
an altitude higher than 1000m (3330 ft), contact an Eaton service representative for
important information about high altitude operation. The operating environment must
meet the weight, clearance, and environmental requirements specified.
The FI-UPM installation must meet the following guidelines:
S The system must be installed on a level floor suitable for computer or electronic
equipment.
S The system must be installed in a temperature and humidity controlled indoor area
free of conductive contaminants.
S The cabinet must be installed in line‐up‐and‐match configuration.
Failure to follow guidelines may void your warranty.
The FI-UPM operating environment must meet the maximum weight requirements
shown in Table 3‐1 and the size requirements shown in Figure 3‐1 through Figure 3‐6.
Dimensions are in millimeters (inches).
Table 3‐1 includes the weights of the heaviest cabinet configuration. Actual weights
may be less due to the installed configuration. Weights are in kilograms (pounds).
Figure
FIELD INSTALLED UPM INSTALLATION PLAN AND UNPACKING
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
3-2
Table 3‐1. FI-UPM Cabinet Maximum Weight
Model
Maximum Weight
kg (lb)
Shipping Installed
Power Xpert 9395P FI-UPM 496 (1094) 471 (1037)
The FI-UPM cabinet uses forced air cooling to regulate internal component
temperature. Air inlets are in the front of the cabinet and outlets are in the top. Allow
clearance in front of and above each cabinet for proper air circulation. The clearances
required around the FI-UPM cabinet are shown in Table 3‐2. Dimensions are in
millimeters (inches).
Table 3‐2. FI-UPM Cabinet Clearances
From Top of Cabinet 457.2 mm (18”) minimum clearance for ventilation
From Front of Cabinet 914.4 mm (36”) working space
From Back of Cabinet None Required
From Right Side of Cabinet None Required
From Left Side of Cabinet None Required
The basic environmental requirements for operation of the FI-UPM are:
S Ambient Temperature Range: 0–40°C (32–104°F)
S Recommended Operating Range: 20–25°C (68–77°F)
S Maximum Relative Humidity: 95%, non-condensing
The FI-UPM ventilation requirements are shown in Table 3‐3.
Table 3‐3. FI-UPM Air Conditioning or Ventilation Requirements During Full Load Operation
Rating Input/Output Voltage
Heat Rejection
kW (1000 BTU/hr)
Ventilation Required for
Cooling Air Exhaust
225 kVA
480/480 7.9 (27.1)
Approximately
950 liter/sec
(2000 CFM)
250 kVA
480/480 9.3 (31.9)
275 kVA
480/480 10.6 (36.1)
300 kVA
480/480 10.6 (36.1)
FIELD INSTALLED UPM INSTALLATION PLAN AND UNPACKING
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
3-3
Dimensions are in millimeters [inches].
1880
[74.0]
735.9
[29.0]
Figure 3‐1. FI-UPM Cabinet Dimensions (Front View)
FIELD INSTALLED UPM INSTALLATION PLAN AND UNPACKING
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
3-4
871
[34.3]
831.5
[32.7]
39.5
[1.6]
192.4
[7.6]
149.2
[5.9]
Dimensions are in millimeters [inches].
Figure 3‐2. FI-UPM Cabinet Dimensions (Right Side View)
Front
Dimensions are in millimeters [inches].
510.1
[20.1]
758.83
[29.9]
Figure 3‐3. FI-UPM Cabinet Dimensions (Top View)
FIELD INSTALLED UPM INSTALLATION PLAN AND UNPACKING
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
3-5
Front
602.8
[23.7]
213
[8.4]
Dimensions are in millimeters [inches].
Figure 3‐4. FI-UPM Cabinet Dimensions (Bottom View)
Front
12.7 [0.5] X 15.8 [0.62] Slot (6X)
830
[32.7]
346
[13.6]
346
[13.6]
69
[2.7]
39.2
[1.54]
59.2
[2.4]
848
[33.4]
730
[28.7]
808
[31.8]
Dimensions are in millimeters [inches].
Figure 3‐5. FI-UPM Cabinet Dimensions (Bottom View with Mounting Brackets)
FIELD INSTALLED UPM INSTALLATION PLAN AND UNPACKING
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
3-6
468
[18.4]
830
[32.7]
1800
[74.0]
918
[36.1]
736
[29.0]
290
[11.4]
CG
CG
Dimensions are in millimeters [inches].
Figure 3‐6. FI-UPM Cabinet Center of Gravity
3.3 Inspecting and Unpacking the FI-UPM Cabinet
The FI-UPM cabinet is palleted separately for shipping. The cabinet is shipped bolted
to a wooden pallet and protected with outer protective packaging material (see
Figure 3‐7).
W A R N I N G
The FI-UPM cabinet is heavy (see Table 3‐1 on page 3-2). If unpacking and unloading instructions are not
closely followed, the cabinet may tip and cause serious injury.
A V E R T I S S E M E N T !
Les sections de l’onduleur sont lourdes (voir le Table 3‐1). Suivre attentivement les instructions de
déchargement et de déballage pour éviter de renverser les armoires, ce qui pourrait causer de graves
blessures.
1. Carefully inspect the outer packaging for evidence of damage during transit.
C A U T I O N
Do not install a damaged cabinet. Report any damage to the carrier and contact an Eaton service
representative immediately.
A T T E N T I O N !
Ne pas installer une armoire endommagée. Signaler les dommages au transporteur et communiquer avec un
représentant du service Eaton immédiatement.
FIELD INSTALLED UPM INSTALLATION PLAN AND UNPACKING
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
3-7
NOTE For the following step, verify that the forklift or pallet jack is rated to handle the weight of the
cabinet (see Table 3‐1 on page 3-2 for cabinet weight).
2. Use a forklift or pallet jack to move the packaged cabinet to the installation site,
or as close as possible, before unpacking. If possible, move the cabinet using the
pallet. Insert the forklift or pallet jack forks from the right side of the pallet (facing
the cabinet), between the supports on the bottom of the pallet (see Figure 3‐6
for the FI-UPM cabinet center of gravity measurements).
C A U T I O N
Do not tilt the FI-UPM cabinet more than 10° from vertical or the cabinet may tip over.
A T T E N T I O N !
Ne pas incliner les armoires FI-UPM à plus de 10 degrés de la verticale puisqu’elles pourraient se renverser.
3. Set the pallet on a firm, level surface, allowing a minimum clearance of 3m (10 ft)
on each side for removing the cabinet from the pallet.
NOTE The FI-UPM cabinet is shipped with a debris shield covering the ventilation grill on top of the unit.
Do not remove the debris shield until installation is complete.
4. Remove the protective covering from the cabinet.
5. Remove the packing material, and discard or recycle in a responsible manner.
6. Inspect the contents for any evidence of physical damage, and compare each
item with the Bill of Lading. If damage has occurred or shortages are evident,
contact an Eaton service representative immediately to determine the extent of
the damage and its impact on further installation.
NOTE While waiting for installation, protect the unpacked cabinet from moisture, dust, and other harmful
contaminants. Failure to store and protect the FI-UPM properly may void your warranty.
FIELD INSTALLED UPM INSTALLATION PLAN AND UNPACKING
Power Xpert 9395P Field Installed UPM Mechanical Installation Manual S P-164000503 Rev 1
3-8
Figure 3‐7. Power Xpert 9395P FI-UPM Cabinet as Shipped on Pallet
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
