Slendertone Abs7 Manuel utilisateur

Marque: Slendertone

Modèle: Abs7

Taper: Manuel utilisateur

www.slendertone.com

Instruction Manual

Mode D’emploi

Instrucciones de Uso

CONTRA-INDICATIONS, WARNINGS & PRECAUTIONS

Your SLENDERTONE product is indicated for the improvement of abdominal muscle tone, for strengthening of

abdominal muscles, and for the development of a firmer abdomen. Your

SLENDERTONE product is suitable for

use by all healthy adults; however, as with other forms of exercise, some care is needed when using it.

Always follow the guidelines below and read the instruction manual before use. Some of the points below

are gender-specific.

CONTRA-INDICATIONS:

Do not use if:

• You have an electronic implant (e.g. cardiac pacemaker or defibrillator - as your product may interfere

with the proper functioning of the implanted stimulator) or suffer from any other heart problem.

• You have any other form of abdominal implant. The safety has not been established for the use of

electronic muscle stimulators over abdominal implants.

• You are pregnant. The safety of electronic muscle stimulation (EMS) over the pregnant uterus has not

been established.

• You suffer from cancer. The effects of electronic stimulation on cancerous tissue are unknown.

• You are under medical supervision for cognitive dysfunction as you may not be able to comply with

safety instructions.

• The controller is in close proximity (e.g., 1 yard) to shortwave or microwave therapy equipment or you

are connected to high-frequency surgical equipment (e.g. diathermy), because of the risk of device

malfunction due to electronic interference.

• Wearing the product necessitates placement over areas at which drugs/medicines are administered

(short-term or long-term) by injection (e.g., hormone treatments).

WARNINGS:

• The long-term effects of chronic electronic stimulation are unknown.

• The product should not be used while sleeping, because you cannot react to safety information.

Wait before using your

SLENDERTONE product until:

• At least 6 weeks after the birth of your baby. You must consult your doctor before use.

• At least 3 months after having a Caesarean section. You must consult your doctor before use.

• One month after an IUD contraceptive device (e.g., coil) has been fitted. You must consult your doctor

before use.

• The heavy days of your period have finished because vigorous abdominal exercise is not recommended

at this time.

When applying the GelPads™ and belt, always remember to:

• Place the GelPads and belt ONLY on the abdomen as indicated in this manual.

• Avoid placing the GelPads or belt on the front or sides of the neck, across or through the heart (i.e. one

GelPad on the front of the chest and one on the back), in the genital region nor on the head, because

of the risk of stimulating inappropriate muscles and organs.

• Avoid application of GelPads near the thorax may increase the risk of cardiac fibrillation.

• Avoid any recent scars, broken or inflamed skin, areas of infection or susceptibility to acne, thrombosis

or other vascular problems (e.g. varicose veins), or any parts of the body where feeling is limited.

• Avoid areas of injury or restricted movement (e.g. fractures or sprains).

• Avoid placing the GelPads over metal implants. They may be placed on the nearest muscles.

PRECAUTIONS:

• Caution should be used for patients with suspected or diagnosed epilepsy.

• Caution should be used in the following:

- When there is a tendency to bleed internally following an injury or fracture.

- Following recent surgical procedures when electronic stimulation may disrupt the healing process

- Over areas of skin which lack normal sensation

• Your product is not intended for medical use, for the treatment of any medical condition, nor for any

permanent physical changes.

Get your doctor’s permission before using your SLENDERTONE product if:

• You wish to use the product and have a bad back. You should also ensure the intensity is kept low.

• You have any serious illness or injury not mentioned in this guide.

• You have recently undergone a surgical procedure.

• You take insulin for diabetes.

• You want to use it on a young child.

• You suffer from muscle or joint problems.

• You use the product as part of a rehabilitation program.

Adverse reactions:

• Skin irritations and burns have been reported with the use of powered muscle stimulators.

• On very rare occasions, first-time users of EMS have reported feeling light-headed or faint. We

recommend that you use the product while seated until you become accustomed to the sensation.

To reposition GelPads during a session:

• Always pause the program currently running, unfasten the belt and then refasten it behind your back

after the GelPads’ positions have been adjusted.

After strenuous exercise or exertion:

• Always use a lower intensity to avoid muscle fatigue.

Contact

SLENDERTONE or an authorized dealer if:

• Your product is not working correctly. Do not use in the meantime.

• You experience any irritation, skin reaction, hypersensitivity, or other adverse reaction. You should,

however, note that some reddening of the skin under the belt is quite normal during and for a short

time after an exercise session.

Note:

• An effective session should not cause undue discomfort.

Important:

• For first time users, muscle stimulation can be an unusual sensation. We recommend that you begin in

a seated position with low stimulation intensity settings to familiarize yourself with the sensation before

progressing to higher intensity settings.

• Keep your product out of the reach of children.

• The studs and GelPads must not be connected to other objects.

• Do not use your product at the same time as any other device which transfers an electrical current into

the body (e.g., another muscle stimulator).

• Do not touch the GelPads or metal studs while the controller is switched on.

• Do not use while driving, operating machinery or cycling or during any activity in which involuntary

muscle contractions may put the user at undue risk of injury.

• The belt is for single person use only.

• Cease using your product if you are feeling light headed or faint. Consult your doctor if this happens.

• Do not over exert yourself when using muscle stimulation. Any workout should be at a level

comfortable for you.

• Do not use your product if you are wearing a belly-button ring. Remove the ring before you begin a

session.

•

SLENDERTONE will not accept responsibility if the guidelines and instructions supplied with this product

are not followed.

• Although compliant with applicable EMC requirements, this product may still interfere with more

sensitive equipment, please move away or switch off.

Note: If you are in any doubt about using your

SLENDERTONE product for any reason, please consult

your doctor before use.

English

WELCOME

Congratulations on purchasing your SLENDERTONE ABS7. Please read your user manual fully

before using this product.

SLENDERTONE ABS7 is the future of body toning and wellness, giving you the body shape you

desire.

SLENDERTONE ABS7 uses clinically proven EMS technology to exercise all of the muscles of

your abdomen, not just those under the belt. A signal is sent to the abdominal muscles and as

the signal strength increases, the muscles contract. You can use your

SLENDERTONE ABS7 almost

anywhere - while relaxing at home, or even working at the office.

Use your

SLENDERTONE ABS7 five times a week and in just 6-8 weeks, you can expect to achieve

stronger, firmer, more toned abdominal muscles.

For best results we recommend that you use your

SLENDERTONE ABS7 in conjunction with a normal,

healthy diet and exercise.

If you have any difficulty setting up your product or have any other questions or concerns, please

send us an email or call

SLENDERTONE Customer Care on:

1-800-551-2443

Email: [email protected]

www.slendertone.com

USER MANUAL CONTENTS

Your user manual is divided into sections to make it easy to use.

Section 1 Contra-Indications, Warnings & Precautions

Section 2 Introducing the

SLENDERTONE ABS7

Section 3 How does muscle stimulation work?

Section 4 Setting up your

SLENDERTONE ABS7

Section 5 Your first

SLENDERTONE ABS7 session

Section 6 Program details

Section 7 Additional functions

Section 8 Help guide

Section 9 Technical specifcations

Section 10 Product warranty

INTRODUCING YOUR SLENDERTONE ABS7

English

1. Belt:

Your belt has been ergonomically

designed and is fastened around your

waist, under your clothes, during use.

Designed for both men & women, fits

waist sizes 27”- 47” The belt has a

pocket for holding your controller

during use.

2. Controller:

The controller generates signals which

are sent, via the belt and GelPads, to

your muscles to make them contract.

Your controller is rechargeable and

takes approximately 3 hours to charge

fully.

3. Controller Connector:

This connects the controller to the toning belt. Make sure the controller is fully connected to the belt.

IMPORTANT: Do not disconnect the controller from the toning belt until it has been switched off.

4. Pack of three adhesive GelPads:

These adhesive GelPads are placed onto your belt before use. When you wrap the belt around

your waist, these GelPads must be in contact with your skin so that signals can be sent to your

muscles.

SLENDERTONE Battery Charger:

Plug the charger into an electrical outlet and then connect your controller to the charger to charge

your controller’s battery. Please ensure you only use the charger supplied by

SLENDERTONE.

6. Instruction Literature:

This is a detailed guide to using your

SLENDERTONE ABS7.

7. Quick Start Guide:

This is an additional quick start guide to help you get started.

1. On/Off Button ( )

Press and hold this button for 2 seconds to turn your controller

on or off. You may also pause the exercise by briefly pressing

this button.

2. Increase Toning Intensity ( )

Press and hold these buttons to increase the intensity of

the exercise. The right-hand button controls the right-hand

side of your belt. The left-hand button controls the left-hand

side.

3. Decrease Toning Intensity ( )

Press and hold these buttons to decrease the intensity of the

exercise on either side of the belt.

NOTE: To increase or decrease the intensity quicker hold both

intensity up or down buttons and the ( i ) button simultaneously.

4. Program Button ( P )

Press this button to select the toning program you wish to use. There are 10 programs in

total, which are explained later in this manual (page 10).

5. Information Button ( i )

Press this button to see your training information, such as the maximum intensity for your current

or last session and the number of sessions you have completed (see page 12).

HOW DOES THE CONTROLLER WORK?

CONTROLLER DISPLAY

Toning intensity from the left-hand side of the belt.

Toning intensity from the right-hand side of the belt.

Counts down the time left in the current session. Also displays error messages (see page 13).

Appears when the exercise has been paused.

Indicates that the sound is off.

Keylock is active - you cannot change the intensity levels or the program accidentally.

This symbol indicates a poor contact between the controller and the belt or between the

GelPads and the skin (see page 14 for more details).

Shows the battery power remaining.

Number of sessions completed.

Shows the program currently running (1 - 10).

This symbol appears during each contraction phase.

Maximum intensity for the current/ last session.

DISPLAY

SLENDERTONE ABS7 uses electronic muscle stimulation (EMS). This technology has been used in

hospitals and by physical therapists for over 60 years. Here is a summary of how EMS

technology works. The special

SLENDERTONE 3-pad design ensures that all of the abdominal

muscles contract and not only those directly under the GelPads.

EXCLUSIVE PATENTED TECHNOLOGY

Step 1

Signals are sent

between the GelPads

Step 2

The signals switch on the

nerves which control the

abdominal muscles.

Step 3

The nerves, in turn, cause

your muscles to contract

and relax rhythmically.

SETTING UP YOUR SLENDERTONE ABS7

Step 1 - Charge the battery. Insert your charger into an electrical outlet and

then connect it to your controller (Fig. a). It’ll take approximately 2-3 hours to

fully charge the battery. Your controller is fully charged when all three sections

of the battery icon are full. The battery icon will flash when the battery is low

and needs to be recharged.

NOTE: Please ensure you only use the SLENDERTONE ABS7 charger when charging

your controller. Do not leave your controller connected to the charger when

the battery is fully charged.

Step 2 - Connect the controller to the belt. The controller and belt must be

connected for your

SLENDERTONE ABS7 to work. ‘Click’ the controller connector

into the belt connector as shown in Fig. b.

Step 3 - Place the gel pads on the belt.

(i) Turn the belt over so that the 3 silver studs are facing upwards.

(ii) Remove the three adhesive GelPads from their pack. There is 1 large

square GelPad and 2 smaller oval GelPads. One side of each GelPad has

a grid pattern on it while the other side is black.

(iii) Remove the covers from the patterned side of the large GelPad (Fig. c)

and place the patterned side of this GelPad inside the white square over the

middle silver stud.

(iv) Now remove the covers from the patterned side of the two smaller

GelPads and place them either side of the large GelPad (Fig. d).

Fig. a

Fig. b

Fig. c

Fig. d

English

NOTE: The location of the smaller GelPads depends on your waist size. In the example below, the

smaller GelPads are placed nearest to the large, central GelPad. This is for a user whose waist

size is 27"-34". Use the sizing guidelines below to help you choose your correct GelPad location.

BELT SIZES

For waist sizes 40"-47"

For waist sizes 33"-41"

For waist sizes 27"-34"

IMPORTANT:

Before you progress, make sure that all three silver studs are

completely covered by the GelPads. Press the edges of all

three GelPads firmly onto the belt before use.

Step 4 - Remove the covers from the black side of all three

GelPads (Fig. a). Do not throw these covers away as you will need

to put them back onto the GelPads at the end of your session.

NOTE: You should only use SLENDERTONE GelPads with your

SLENDERTONE ABS7 belt.

Step 5 - Position the belt on your body.

Wrap the belt around your waist so that the GelPads are pressed

firmly against your skin, positioning the large square GelPad over

your navel (belly button). Stretch the ends of the belt around your

waist (Fig. b) until the small GelPads are between your hip bone

and ribs on either side of your body (Fig. c). Fasten the belt tightly

around your waist, but not so tight as to cause discomfort. The

GelPads are water-based, so you may find they are cool when

placed on your skin.

NOTE: Use your SLENDERTONE ABS7 whenever it suits you. Very discreet

under your clothes, you can use it almost any time and any place.

For the best results, we recommend that you do five training

sessions per week. You should, however, only do one session

per day, as this allows your muscles to recuperate.

Fig. a

Fig. b

Fig. c

English

YOUR FIRST TONING SESSION

Muscle toning can be an unusual sensation, but a pleasant one. It may tickle to begin with. We

recommend that you use the product while seated until you become accustomed to the sensation.

As you increase the intensity, the sensation goes from a mild tingly feel, to a distinct muscle

contraction. The abs contract and relax like in natural muscle movements. To get started, follow

these simple steps:

Step 1: Press and hold the on/off button ( - Fig. a) for two seconds to

switch your controller on.

Step 2: Select the program you wish to use by pressing the program

button ( P - Fig. b). Then, to start the program, press and hold the increase

intensity buttons ( - Fig. c) until you feel your muscles contracting. Always

choose an intensity level at which you feel a strong but comfortable

contraction. This will vary from person to person. You should try to reach an

intensity level of 15 or higher in your first session. The increasing intensity level

is displayed on the screen.

Step 3: Continue increasing the intensity throughout the session if possible.

You will feel the muscle contractions getting stronger as the intensity increases.

Remember the harder you work your muscles the better the results you will

see, but always reduce the intensity if you feel any discomfort. Your unit’s

intensity range is 0-150.

PAUSING A SESSION

If you wish to pause a session before it is finished, simply press the on/off

button briefly. The display will show that the controller is paused ( ). To

resume the session, briefly press the on/off button again. The display will

return to its normal mode.

Step 4: SESSION OVER

At the end of the training session your

SLENDERTONE ABS7 will stop automatically. However, to switch

off your controller at any time during a session, press and hold the on/off button for two seconds.

You should see the display turn off.

Step 5: Remove the belt and put the covers back on the black side of the GelPads. Store it safely

until your next session.

NOTE: Do not disconnect the controller from the belt without first switching the controller off, as this

may result in an error on your display.

Congratulations on completing your first training session!

Fig. a

Fig. b

Fig. c

PROGAM DETAILS

Your SLENDERTONE ABS7 has 10 toning programs which are listed in the table below. There are

7 Passive Programs (no physical activity required) and 3 Active Programs (while doing a physical

activity). Program 1 is set when you switch your controller on for the first time. The controller will

then automatically progress through each program up to program 6. Programs 7 to 10 must be

selected manually using the program button. The display will show the program currently selected.

1. Passive Programs: without any physical activity

Program 8 is lower in intensity and is useful when you want to combine the stimulation with a

moderate cardio activity such as active walk, jogging, stepper or exercise bike.

CRUNCH PROGRAMS 9 and 10:

What shall I do?

NOTE: Those unfamiliar with Ab Crunch exercises should start with program 9 before progressing

to program 10. Begin both Crunch Programs 9 and 10 in the starting position (Fig. a, page 11).

Wearing your belt, lie on your back. Bend your knees to approx. 90°. Position your hands either

side of your head. Your feet should be flat on the floor, shoulder width apart and your abdominal

muscles fully relaxed. Switch your controller on and increase the intensity.

2. Active Programs: while doing a physical activity

Passive

Programs

Duration in

minutes

Level

Number of

session

1 : Initiation

2 : Beginner

3 : Intermediate

4 : Advanced

5 : Expert

6 : Pro

7 : Ab Power

Easy

Moderate

Advanced

Indefinite

Active

Programs

Duration in

minutes

Level

Physical

exercise

8: Endurance

9: Beginner Crunch

10: Advanced Crunch

Easy

Moderate

Low cardio

Abs front

Abs side

English

Program 9

Beginner Crunch (Fig. a) :

1(a). When the stimulation starts, gently press your lower back into the floor and contract your

abdominal muscles as hard as is comfortable. Do not raise your head off the floor and keep your

neck muscles as relaxed as possible.

Standard Crunch (Fig. b) :

1(b). When the stimulation starts, slowly curl your shoulders forward, making sure that your lower

back stays on the floor. Ensure you do not jerk your head forward. When raising your head, avoid

neck strain by keeping a space approximately the size of your fist between your chin and your chest.

Program 10

Side Crunch (Fig. c) :

2. Hold each contraction for three seconds, then return to the starting position and relax fully. The

stimulation will stop.

3. After a three second relaxation period, the stimulation starts again. Repeat step 1(a) or 1(b) and

step 2 depending on the type of crunch you are doing.

1. When the stimulation starts, slowly curl one shoulder upwards and towards the midline/centre of

your body. Your shoulder should finish 8-10cm (3-4") from the ground. Keep your lower back on

the floor.

IMPORTANT:

Curl your right shoulder upwards and inwards when the stimulation is on the left side of your abdomen.

Curl your left shoulder upwards and inwards when the stimulation is on the right side of your abdomen.

Always keep your lower back on the floor and never twist your upper body excessively.

2. Hold each contraction for two seconds, then return to the starting position and relax fully - the

stimulation will stop.

3. After a two-second relaxation period, the stimulation will start again.

4. Repeat steps 1-3.

Fig. a

Fig. b

Fig. c

Fig. a

Fig. b

Information Button ( i )

Your

SLENDERTONE ABS7 controller stores information about current and previous

sessions which can be accessed by using the information button. You can

access this information while a program is running.

1. Current Intensity Levels

Press the information button (Fig. a) once to display the intensity of the current program

2. Average Intensity Levels

Press the information button twice to see the average intensity reached in the last session.

3. Highest Intensity Levels

Press the information button three times to display the highest intensity reached in the last session.

4. Number of Sessions of the Current Program

Press the information button four times to see how many sessions performed at the current

program level. Please note that this resets to zero when a new program is selected or

when more than 99 sessions are performed.

5. Total Number of Sessions

Press the information button five times to display the total number of sessions you have

completed to date. Please note that this resets to zero if more than 1000 sessions are performed.

6. Garment type

Press the information button six times to display the garment type you are using.

7. Press the information button seven times and the controller will return to normal.

Mute Function ( )

If you want to switch off your unit’s sound effects, press and hold the

program button for two seconds (Fig. b). The mute function remains

active indefinitely unless manually changed. Deactivate the mute function

by again pressing the program button for two seconds.

ADDITIONAL FUNCTIONS

Fig. c

Keylock Function ( )

If you find a comfortable exercise intensity, press and hold the information

button for two seconds to lock that intensity (Fig. c). This function only

remains active during the session in which it is activated. If you wish to

increase the intensity further, deactivate the keylock function by again pressing

the information button for two seconds.

Fig. d

Fig. e

Fig. f

Error Messages

In the unlikely event of your product developing a problem, “Err” will appear

on your controller display (Fig. d). If this occurs you should switch the controller

off and then switch it back on again. It should now operate properly. If the

problem persists, please call

SLENDERTONE Customer Care for further assistance

(see page 4).

Battery Power / Replacing the battery

The battery icon on the display will flash when the battery is low and needs

to be recharged. After a period of time, you may find that your battery will

only power your controller for a limited number of sessions, requiring you

to charge the battery more frequently. This is because rechargeable batteries

have a limited number of charge cycles and may eventually need to be

replaced.

Should you need to replace the rechargeable battery, remove the small

rubber plug from the back cover of your controller (Fig. e), unscrew the

back cover and remove it. Replace the existing battery pack with a new

battery pack (Fig. f ) and replace the battery cover. You can purchase a

new battery pack by contacting

SLENDERTONE Customer Care.

BATTERY CHARGING AND DISCHARGING

Your device is powered by a rechargeble battery. The full performance of a new battery is achieved

only after two or three complete charge cycles (fully charged and discharged).

The battery can be charged and discharged hundreds of times, but it will eventually wear out. To

ensure optimum battery performance you should use your product regularly e.g. perform 1 session

a day, 5 days per week. Use the battery only for its intended purpose. Never use any charger or

battery that is damaged.

If a replacement battery is being used for the first time or if the battery has not been used for a

prolonged period, it may be necessary to connect the charger and then disconnect and reconnect

it to start the charging. If the battery is completely discharged, it may take a few minutes before the

charging indicator apperas on the display.

Unplug the charger from the electrical socket and the controller when it is not in use. Do not leave

a fully charged battery connected to a charger, since overcharging may shorten its lifetime. If left

unused, a fully charged battery will lose its charge over time.

Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions,

will reduce the capacity and lifetime of the battery. Always try to keep the battery between 59°F

and 77°F. A device with a hot or cold battery may not work temporarily, even when the battery is

fully charged. Battery performance is particularly limited in tempertaures well below freezing. Do

not dispose of batteries in a fire as they may explode. Batteries may also explode if damaged.

Dispose of batteries according to local regulations. Please recycle when possible. Do not dispose

as household waste.

English

* The symbol always appears in conjunction with the left/right intensity indicators. If the left indicator

appears, there is a problem with the left

GelPad, the right indicator acknowledges a problem with the right

GelPad and if both indicators appear there is a problem with either the middle GelPad or all three GelPads.

Display doesn’t come

on / no signal from

the controller

The display is on but

there is no signal.

The battery symbol is

flashing

The symbol has

appeared on the

display* and/ or the

controller is beeping

Unpleasant feeling

beneath the gel pads

The contractions are

very weak even when

the toning intensity is

high

“Err” appears on the

display

QUICK GUIDE TO SOLVING PROBLEMS

Problem Possible Cause Solution

The battery is low

Controller not properly connected to

the belt

The GelPads are on the wrong way

around

The covers are still on the GelPads

The GelPads are worn

The GelPads are not covering the

studs

Build up of gel on the metal studs

Poor GelPad contact with the skin

The GelPads are worn

Build up of gel on the metal studs

The GelPads are not covering the

studs

Too many consecutive sessions

The

GelPads are worn

The battery is low

Poor

GelPad positioning

GelPads are not covering the metal

studs

Error message

Recharge the battery

Ensure the controller and belt are properly

connected

Ensure the black surface of the GelPads

are facing you

Remove the covers from the GelPads

Visit www.slendertone.com or contact

Customer care for replacement GelPads

Make sure the GelPads fully cover the

metal studs

Clean the metal studs with a clean, dry cloth

Press the GelPads firmly against the skin.

Smear a few drops of water on the surface

of the GelPads. Make sure the controller is

OFF first

Visit www.slendertone.com or contact

Customer care for replacement GelPads

Clean the metal studs with a clean, dry cloth

Reposition the GelPads so the metal studs

are covered

You should just do one session per day on

any single body area

Visit www.slendertone.com or contact

Customer care for replacement GelPads

Recharge the battery

See page 8 for correct gel pad positioning

Reposition the

GelPads so the metal studs

are covered.

Switch the controller off and on. The

controller should work without any problem.

If the error message persists call Customer

Care for advice.

English

FREQUENTLY ASKED QUESTIONS

Can I use SLENDERTONE ABS7 for post natal exercise?

• Yes, but you must wait a minimum of 6 weeks after childbirth before you begin using it and you

must consult your doctor first.

• If you’ve had a Caesarean in the past 3 months, consult your doctor for approval before using

the belt.

The stimulation is uncomfortable. How can I improve this?

• Make sure the GelPads are positioned correctly and that they are pressed firmly against your

skin - see page 7 & 8. Switch off your controller and reposition the belt if necessary.

• You can also smear a few drops of water on the black surface of the GelPads. This can improve

the comfort of the muscle stimulation, but be careful not to get water on the controller. Ensure

the controller is switched OFF before you do this!

• Ensure the metal studs are fully covered by the GelPads.

My skin is red after the exercise. Is this a problem?

• Some redness of the skin after a toning session is normal. It is partly due to an increase in the

blood flow under the skin and should fade after a while. You may also experience some reddening

of the skin due to the pressure of the belt. This is the same as the pressure marks you get from

tight clothing. You should not be concerned about this. It should fade soon after you remove the belt.

• If the redness is excessive, you may have the toning intensity too high. This may increase the

reddening in sensitive skin. Try using a lower toning intensity for a few days. If the problem persists,

you should stop using the product.

Will the controller cause muscle soreness?

• As with all exercise some muscle soreness can occur after using the belt. This is normal and

should go away after a day or two. Use a low toning intensity for a few sessions if you are

experiencing muscle soreness.

I can feel a tingling sensation in my legs during an exercise. What should I do?

• This indicates that the GelPads are over your hip-bones. Moving the two smaller GelPads upwards

and inwards on your waist (i.e. towards the centre of your body) should prevent this. Remember

to pause or switch off your

SLENDERTONE ABS7 before adjusting the belt or GelPads.

How do I know when to replace the GelPads?

• With time the GelPads pick up skin debris and may need to be replaced as this makes the

workout less effective and less comfortable.

• You may notice the signal is weakening even if the batteries are OK. This usually indicates that the

GelPads are wearing and will soon need replacing. You can check this by first adjusting the belt to

ensure correct positioning of the GelPads. If the problem persists, try using the controller with a

new battery pack. If the signal is still weak or uncomfortable, you should order new GelPads.

• New GelPads can be purchased online at www.slendertone.com (check for special offers) or from

Customer Care.

I can feel my waist muscles exercising but not my stomach muscles.

• Pause the program and reposition the central GelPad slightly lower on your stomach. If this

doesn’t help, move the 2 small GelPads to a smaller figure setting on the belt (towards the

central GelPad).

CARING FOR YOUR BELT

I can feel my stomach muscles exercising but not my waist muscles.

• Pause the program and reposition the central GelPads slightly higher on your stomach. If this

doesn’t help, move the 2 smaller GelPads to a larger figure setting on the belt (away from the

central GelPad).

What is the difference between

SLENDERTONE’s belts and the other ab belts?

• The technology used by

SLENDERTONE is the only one able to exercise all of your abdominal muscles:

rectus, transversus and obliques.

•

SLENDERTONE’s technology is exclusive, patented and clinically proven.

Battery performance has degraded significantly.

• After an extended period of time you may notice a degradation in the performance of the battery

in your controller. At this point you should purchase a new rechargeable battery pack. New

rechargeable battery packs can be purchased through

SLENDERTONE Customer Care, or by visiting

www.slendertone.com.

Your belt can be washed, but you must first remove the controller and GelPads. Always follow the

instructions on the label when washing the belt.

Never machine wash your belt. Always hand wash in lukewarm water. This protects the

internal wiring from damage in the washing machine. You should take care even when

hand washing and never wring the belt to remove water.

Do not use bleach when washing the belt.

Do not dry clean your belt.

Do not tumble dry your belt. Dry the belt on a flat surface. Do not dry it over anything hot.

(e.g. a radiator) as the belt contains plastic parts. Ensure the belt is completely dry before

using it again.

The belt should not be ironed.

Belt Materials:

Outer material: 100% Nylon; Binding: 82% Nylon, 18% Elastane; Hook & Loop: 100% Nylon;

Foam: 100% Polyurethane.

English

CARING FOR YOUR GELPADS

30-DAY PLAN

• The GelPads are for single person use only.

• You should ensure your skin is clean and free of oils, creams and other lotions before use.

• The durability and effectiveness of the GelPads depends entirely on the proper use, storage and

care on the part of the user, certain skin types and the type, duration, number of sessions,

intensity used and site of stimulation.

• Ensure your hands are clean before handling GelPads. You should avoid touching the skin-side

of the GelPads with your fingers as much as possible when applying or removing the belt, as this

can transfer oils and skin particles to the GelPads’ surface.

• After use, replace the liners on the black side of the GelPads and store your product in a cool,

dry place until the next use.

• The GelPads will need to be replaced periodically as the surface picks up skin debris and

becomes dry over time.

To help you get the most from your

SLENDERTONE ABS7, we recommend that you follow our 30-day

plan. To follow this plan, use your belt 5 times a week for 4 weeks and record your highest intensity

levels in your diary (page 21). Each week you have two rest days to allow your muscles to recover.

The diary below shows one person’s toning intensity, recorded during scientific testing over a

30-day period.

We recommend that you follow a similar plan, trying to push yourself to use higher toning intensity

levels all the time. Try to increase your toning intensity from week to week. But remember, do not

over-exert yourself when using muscle stimulation. Any workout should be at a level comfortable

for you.

Each box shows the average toning intensity from either side of the belt.

Fill-in your diary every time you complete a toning session. Leave this diary somewhere you will

see it regularly. This will help to motivate you to reach your goal. You will soon see and feel that

your ab muscles are firmer and more toned.

NOTE: The intensity level will vary from person to person.

EXAMPLE:

Week

Day 1

(40 40)

rest

Day 2

rest

(70 70)

(95 95)

(110 110)

Day 3

(40 40)

(80 80)

(105 105)

(115 115)

Day 4

rest

Day 5

(50 50)

(80 80)

(105 105)

(115 115)

Day 6

(50 50)

(80 80)

(110 110)

(120 120)

Day 7

(60 60)

(90 90)

(110 110)

(120 120)

TECHNICAL SPECIFICATIONS

Caring for your controller

Your controller should not be allowed to get wet or be left in excessive sunlight. Itv may be cleaned regularly

using a soft cloth, lightly dampened in soapy water. Do not allow the interior of your controller to become wet.

Do not use detergents, alcohol, spray aerosols or strong solvents on your controller.

Access to the interior of the controller is not required for maintenance purposes.

If your controller is damaged, you should not use it but should return it to SLENDERTONE or your local distributor for

replacement or repair. Repairs, service and modifications may not be carried out by anyone other than qualified

service personnel authorised by SLENDERTONE.

IMPORTANT: Under no circumstance should anything other than the correct type of batteries - (rechargeable

batteries 3.6V NiMH) be used with your controller. These can be purchased from the SLENDERTONE careline.

Disposing of the GelPads and batteries

Used GelPads and batteries must never be disposed of in a fire but in accordance with your country’s national

or state laws governing the disposal of such items.

Accessories:

Under no circumstances should anything other than SLENDERTONE accessories be used with your SLENDERTONE

charger or SLENDERTONE controller (Type 390). Any others may not be compatible with your controller and could

degrade the minimum safety levels. You can purchase all accessories at www.slendertone.com.

SLENDERTONE ABS7 GelPads: • 1 large GelPad (Type 732)

• 2 small GelPads (Type 733)

Battery Pack: (3.6V, NiMH)

Battery Charger:

EU: 2504-0321 + 2504-0324 + 2504-0325 US/Japan: 2504-0322

Australia: 2504-0321 + 2504-0329 Korea: 2504-0321 + 2504-0323

Charger complies to EN 60950, Input: nominal voltage 100-240V, frequency 50-60Hz, current 125mA. Do not

use any other chargers or any other power supplies.

Classification: Internally powered equipment, Class II charger, Type BF applied parts.

Product Type: 390

Intended use: Muscle stimulator

Waveform: Symmetrical bi-phasic square waveform when measured into a resistive load.

Attention:

This product can deliver currents in excess of 2mA/cm² if used with incorrect electrodes.

NOTE: The signal gradually increases to a peak intensity level at the start of the contraction phase (i.e. ramp up)

and gradually decreases to nothing at the start of the relaxation phase (i.e. ramp down). When the symbol

is flashing, the stimulus is significantly reduced.

Environmental Specifications:

Operating Range:

Transport & Storage Range:

Temperature: 32 - 95°F

Humidity: 20 - 65 % RH

Temperature: 32 - 131°F

Humidity: 10 - 90 % RH

Description of your controller’s symbols:

There are a number of technical markings on your controller. These can be explained as follows:

The controller and belt are manufactured for Bio-Medical Research Ltd, Parkmore Business Park West,

Galway, Ireland.

The controller requires 1 x 3.6 volt (NiMH) DC battery pack. DC is indicated by the symbol:

The Output Frequency indicates the number of pulses per second transmitted by the controller. This is measured

in hertz, which is indicated by “Hz”.

Output (RMSA) means the maximum output root mean square current for each channel.

Output (RMSV) means the maximum output root mean square voltage for each channel.

This symbol means “Attention, consult the accompanying documents”.

This symbol means type BF applied parts (GelPads).

Conforms to UL STD 60601-1.

Certified to CAN/CSA.

STD C22.2 NO 601.1

SN stands for ‘serial number’. On the label on the back of the controller is the serial number specific to this product.

The letter preceding the number indicates the year of manufacture, where “U” denotes 2015, “V” denotes 2016 etc.

The belt’s batch number is represented on the belt packaging, by the number corresponding with the LOT symbol.

At the end of the product lifecycle, do not throw this product or batteries into the normal household

garbage, but bring it to a collection point for the recycling of electronic equipment.

Some product materials can be re-used if you bring them to a recycling point. By re-using some

parts or raw materials from used products you make an important contribution to the protection of

the environment. Please contact your local authorities if you need more information about collection

points in your area.

Waste Electrical and Electronic Equipment can have potentially harmful effects on the environment.

Incorrect disposal can cause harmful toxins to build up in the air, water and soil and can be harmful

to human health.

Rated Outputs – Voltage/Currents: X:70

Parameter

Output RMSV

Output RMSA

Output Frequency

DC Component: Approx.

Positive Pulse Width:

Negative Pulse Width:

Interphase Interval:

7.35V

14.7mA

50-70Hz

0 C

200-315µs

100µs

13.1V

13.1mA

50-70Hz

0 C

200-315µs

100µs

15.5V

10.3mA

50-70Hz

0 C

200-315µs

100µs

500Ω 1KΩ 1K5Ω

English

PRODUCT WARRANTY

Dear Customer,

Thank you for purchasing your SLENDERTONE product ("Product"). To be covered by this Limited Warranty, the

Product must have been purchased directly from Slendertone Distribution, Inc. ("SDI"), or its authorised retailer

in the United States. This Limited Warranty extends only to the original purchaser and cannot be transferred to

anyone. Please read this carefully before using the Product.

Our Limited Warranty to you

SDI warrants to you, the original purchaser, that under normal use and service, the Product will be free from

defects in material and workmanship for a period of two (2) years from the date of purchase ("Warranty

Period"). If you discover a defect covered by this Limited Warranty during the Warranty Period, and return the

Product to us, we will repair or replace the Product, at our option, using new or remanufactured components.

There is no warranty or condition of any kind as to any defects discovered after the Warranty Period expires.

Certain Product failures not covered

This Limited Warranty covers defects in manufacture that arise from correct use of the Product per the product

manual and instructions. It does not cover damage caused by abuse, misuse, accidents, modification or repair

by any person other than SDI, moisture, extreme heat or cold, corrosive environments, high voltage surges

from external sources or an unsuitable power supply. This Limited Warranty does not cover normal wear and

tear on consumable items (e.g. GelPads, garments, etc.). This Limited Warranty does not apply to any battery

provided with the Product, or if the Product has an altered or defaced serial number.

How to obtain service under this Limited Warranty

To obtain service under this Limited Warranty, please contact SDI’s Customer CareLine at 1-800-551-2443 to

obtain return instructions. You must submit proof of purchase in the form of a bona fide, dated bill of sale,

receipt, or invoice (or copy thereof) evidencing that your request for service is made within the Warranty Period.

Except as may otherwise be required by legislation in your State, SDI will not be responsible for the cost of

returning the Product or for any damage to or loss of the Product while it is in transit to us. We recommend

that you use a carrier that will track your shipment and ensure the Product’s safe delivery. SDI cannot accept

any returns sent C.O.D.

THIS LIMITED WARRANTY IS THE ONLY WARRANTY FOR THE PRODUCT, AND THERE ARE NO OTHER

EXPRESS WARRANTIES, ORAL OR WRITTEN, PROVIDED BY SDI. ANY IMPLIED WARRANTIES APPLICABLE

TO THE PRODUCT, INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICU-

LAR PURPOSE, ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD SET FORTH ABOVE.

Limitation of Remedies

YOUR EXCLUSIVE REMEDY, IN LIEU OF ALL INDIRECT, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY,

SPECIAL OR OTHER DAMAGES OF ANY KIND, INCLUDING FOR NEGLIGENCE, IS LIMITED TO THE

REPAIR OR REPLACEMENT OF THE PRODUCT, IF DEFECTIVE, UNDER THE TERMS AND CONDITIONS

OF THIS LIMITED WARRANTY.

SDI will bear no other expenses.

SDI reserves the right to refuse to repair or replace the Product if it is returned in an unsanitary condition. SDI

reserves the right to substitute a product of equal or better quality if an identical product is not available at the

time of replacement. This Limited Warranty is non-transferable.

Applicability of state law

Some states do not allow limitations on the duration of implied warranties, or the exclusion or limitation of incidental

or consequential damages, and so the related limitations and exclusions stated above may not apply to you.

Governing law

This Limited Warranty is valid in the United States only and is not applicable in other countries. If you acquired

the Product in the United States, the laws of the State of New York will apply to this Limited Warranty.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER

RIGHTS, WHICH VARY FROM STATE TO STATE.

La page charge ...

Slendertone Abs7 Manuel utilisateur

Marque: Slendertone

Modèle: Abs7

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Slendertone Abs7 User manual
español: Slendertone Abs7 Manual de usuario

Slendertone Abs7 Manuel utilisateur

Slendertone Abs7 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents